The electrical, mechanical and thermal conductivity of ethylene butene copolymer (EBC) composites with carbon fibers were studied. EBC/carbon-fiber composites can be utilized as an electro-mechanical material which is capable of changing it electric resistance with mechanical strain. Carbon fibers were introduced to EBC with different concentrations (5-25 wt%). The results showed that the addition of carbon fibers to EBC could increase the electric resistance up to 10 times. Increasing the load to 2.9 MPa could increase the electric resistance change by 4500% compared 25% fiber sample with pure EBC. It is also noted that the electric resistance of the EBC/CF composites underwent a dramatic increase with raising the strain, for example, the resistance change was around 13 times more at 15% strain in comparison to 5% of strain; The thermal conductivity tests showed that the addition of carbon fibers could increase the thermal conductivity by 40%, from 0.19 to 0.27 (Wm-1K-1). It was also observed that the addition of carbon fibers to EBC could increase the thermal conductivity.

The development of cost-effective methods for estimating hydraulic conductivity profiles has been an ongoing effort in the field of engineering practice, which can be used to increase availability to clarify the hydrogeological complexity of fractured rock aquifers for the aid of solving groundwater-related problems. A methodology is presented, which combines electrical well logs, fluid conductivity logs, double packer hydraulic tests, Archie’s law, and the Kozeny-Carman-Bear equation to investigate relations between formation factor and hydraulic conductivity. This method was applied to develop hydraulic conductivity profiles based on the data collected from 88 boreholes in Taiwan's mountainous areas. The investigation results include: (1) Well logging signals were suggested to be categorized by rock types to establish effective relationships with hydraulic conductivity. (2) Removing the mud-bearing section data with two proposed data clustering techniques could effectively enhance the correlation between the formation factor and hydraulic conductivity. (3) The predictive models for estimating hydraulic conductivity have been developed for sandstone, schist, and slate. (4) The prevalence of clay content in most of Taiwan's mountainous rock formations has been found, which implies that careful consideration of clay-related issues in complex geologic formations is essential while applying Archie's law theory.

This paper has experimentally measured volcanic tufa electrical conductance. The calculations are carried out in accordance with the potential of cyclic voltammetry in a constant state. The cyclic voltammograms nanoelectrode platinum prepared electrochemically were examined in the range -0.2 to 1.2 V vs. AgCl [Cl^-]:1.0 M in the presence and absence of volcanic tuff in the aqueous solution of 1.0 M HCl. The cyclic voltammetry studies show that the Nano platinum film suffers degradation when the potential exceeds +0.85 V, and below this potential, it is quite stable. The redox reaction of the electrode is reversible. The nanoparticle platinum synthesized at low temperature and high acid concentration exhibits higher electronic conductivities. It has been observed that, relative to area under the peak aggregate tests, the use of volcanic concrete was showing a large increase in electrical conductivity. It was shown that with cyclic voltammetry, three well-defined anode peak could be achieved at a power of 0.0, 0.4 and 0.6 V versus Ag/AgCl.

Previously, a conductivity invariance phenomena (CIP) has been discovered – at a certain lift-off, the inductance change of the sensor due to a test sample is immune to conductivity variations, i.e. the inductance – lift-off curve passes through a common point at a certain lift-off, termed as conductivity invariance lift-off. However, this conductivity invariance lift-off is fixed for a particular sensor setup, which is not convenient for various sample conditions. In this paper, we propose using two parameters in the coil design – the horizontal and vertical distances between the transmitter and the receiver to control the conductivity invariance lift-off. The relationship between these two parameters and the conductivity invariance lift-off is investigated by simulation and experiments and it has been found that there is an approximate linear relationship between these two parameters and the conductivity invariance lift-off. This is useful for applications where the measurements have restrictions on lift-off, e.g. uneven coating thickness which limits the range of the lift-off of probe during the measurements. Therefore, based on this relationship, it can be easier to adjust the configuration of the probe for a better inspection of the test samples.

Herein, we report on a giant thermoelectric figure of merit of a non-degenerate fluorine-doped single-walled carbon nanotube (FSWCNT) using a tractable analytical approach and the phonon lattice Boltzmann model (LBM). We investigate the influence of the doping concentration, and the overlapping integrals on the ZT. The ZT and the temperature range of operation can be tuned using the doping (impurity) concentration and the overlapping integrals, respectively. The lattice thermal conductivity obtained using the phonon LBM was calculated to be 107.2 W/mK which yielded a ZT greater than 20. Interestingly, the ZT obtained is higher than what has been reported in superlattices, (ZT~1.4) and superlattice nanowire, (ZT~ 4) at 300 K, making FSWCNT a potential candidate for thermoelectric applications.

Had magnetic monopoles been ubiquitous as electrons do, we would have probably had a different form of matter, and power plants based on currents of these magnetic charges would have been a familiar scene of modern technology. Magnetic dipoles do exist however, and in principle one could wonder if we can use them to generate magnetic currents. In the present work, we discuss the issue of generating magnetic currents and magnetic thermal currents in electrically-insulating low-dimensional Heisenberg antiferromagnets by invoking the (broken) electricity-magnetism duality symmetry. The ground state of these materials is a spin-liquid state that can be described well via the Jordan-Wigner fermions, which permit an easy definition of the magnetic particle and thermal currents. The spin-liquid states in these antiferromagnets are either gapless or gapped liquids of spinless fermions whose flow defines a current just as the one defined for electrons in a Fermi liquid. The driving force for the magnetic current is a magnetic field with a gradient along the magnetic conductor. The present work is about claiming that what the experiments in spintronics attempt to do is trying to treat the magnetic degrees of freedoms on the same footing as the electronic ones.

Soil water loss by evaporation influences the sodium adsorption ratio (SAR) of irrigation drainage water. Evaporation concentrates sodium and magnesium but calcite precipitation has a more complicated effect on soluble calcium and alkalinity. Here we propose a revised sodicity hazard assessment that quantifies the impact of evaporative water loss and calcite precipitation on drainage water SAR. This paper shows sodicity hazard is determined by the initial composition of irrigation water as originally suggested by previous researchers, and provide a simple, accurate way to identify the potential sodicity hazard of any irrigation water. In particular, the initial equivalent concentration of alkalinity and calcium determine the salinization pathway followed during evaporation. If the irrigation water alkalinity exceeds soluble calcium expressed as equivalent concentrations, drainage water SAR approaches an upper limit determined by the initial relative concentration of sodium and magnesium. If irrigation water alkalinity is less than soluble calcium, drainage water SAR approaches a lower limit determined by the initial calcium, magnesium and sodium. In both cases the SAR is scaled by the square root of the concentration factor √Fc quantifying soil water loss. To assess the impact of evaporation and calcite precipitation on the SAR and test the accuracy of the new sodicity hazard assessment, we evaluated data from previously published lysimeter studies. We plotted water composition boundaries for each source water, comparing these boundaries to the drainage water composition recorded in the lysimeter studies. As salinity increased by evaporation, each drainage water followed a distinct salinization path.

Background: Electrical conductivity of trabecular bone at 100 kHz was recently reported as a good predictor of bone volume fraction. However, to quantify its relationship with the free water (or physiological solution) content and between the conductivities of its constituents, is still unclear. Methods: In this contribution, in silico models inspired by microCT images of trabecular bovine samples were used to build realistic geometries. Finite Element Method was applied to solve the electrical problem and to robustly fit the conductivity of the constituents with literature data. The obtained effective electrical conductivity was compared to Bruggeman three media mixture model: physiological solution, bone marrow and bone matrix. Results: The values for physiological solution plus bone marrow and bone matrix that captured better the bone volume fraction in the two media Finite Element model were: σps+bm = 298.4 mS/m and σb = 21.0 mS/m, respectively. Additionally, relative good results were obtained by a three media Bruggeman mixture model with σbm= 103 mS/m, σb= 21.0 mS/m, and σps= 1200 mS/m. Simple linear relationships between the proportions of constituents depending on bone volume fraction were tested. Degree of anisotropy and fractal dimension do not show detectable changes in effective conductivity. Conclusions: These results provided some useful findings for simulation purposes: first, a higher value of electrical conductivity of bone marrow has to be used in order to obtain similar values to those experimental published data. Second, anisotropy is not detectable by conductivity measurements for small trabecular samples (cube 5 mm). Finally, the simulations presented here showed a relatively good fitting of the mixture Bruggeman model which potentially would allow both, accounting for the free water content and re-scaling the model for whole bone electrical simulations.

Sr2FeMoO6-δ (SFMO) double perovskite is a promising candidate for room-temperature spintronic applications since it possesses a half-metallic character (with theoretically 100% spin polarization), a high Curie temperature of about 415 K, and a low-field magnetoresistance (LFMR). However, due to different synthesis conditions of ceramics as well as thin films, different mechanisms of electrical conductivity and magnetoresistance prevail. In this work, we consider the weak localization effect in SFMO occurring in disordered metallic or semiconducting systems at very low temperatures due to quantum interference of back-scattered electrons. We calculate the quantum corrections to conductivity and the contribution of electron scattering to the resistivity of SFMO. We attribute the temperature dependence of SFMO ceramics resistivity in the absence of a magnetic field to the fluctuation induced tunneling model. Also, we attribute the decreasing resistivity in the temperature range from 409 K up to 590 K to adiabatic small polaron hopping and not to localization effects. Both fluctuation induced tunneling and adiabatic small polaron hopping do not favor quantum interference. Additionally, we demonstrate that the resistivity upturn behavior of SFMO cannot be explained by weak localization. Consequently, to the best of our knowledge, there is still no convincing evidence for the presence of weak localization in SFMO.

The analysis of high-temperature physicochemical properties of theK₃AlF₆-Na₃AlF₆-AlF₃ molten salt system is crucial for practical production of electrolytic aluminum. In this paper, the physicochemical properties of the K₃AlF₆-Na₃AlF₆-AlF₃ molten salt electrolyte system at 1173 K and standard atmospheric pressure were simulated using molecular dynamics calculations. The effects of Zr、B、C、W、Ti、Hf、Nb、and Ta on the radial distribution function, coordination number, viscosity and conductivity of the electrolyte system are discussed in detail. The simulation results show that the coordination number between Al-F and the conductivity is decreasing as the content of B²- increases. And the coordination number between Al-F and the viscosity is decreasing as the content of Zr⁴⁺ increases. With the addition of impurity elements such as C, W, Ti, Hf, Nb, and Ta, the data show that C has no significant effect on this electrolyte system, while the presence of W will decrease the coordination number between Al-F in the system. The presence of Ti, Hf, Nb, and Ta may intensify the decomposition reaction between one of the Al-F ligands, which increases the coordination number between Al-F and the number of ions in the electrolyte. This work provides theoretical support for the subsequent study of inert anodes containing Zr, B, Ti, Hf, Nb, and Ta.

In the present work freezing and melting characteristics of water seeded with chemically functionalized graphene nano-platelets in a vertical cylindrical capsule was experimentally studied. The volume percentage of functionalized graphene nano-platelets was varied from 0.1% to 0.5% with an interval of 0.1%. The stability of the synthesised samples were carried out by zeta potential distribution. The thermal conductivity of the nanocomposite samples were experimentally measured using transient hot wire method. A maximum enhancement of ~24% in the thermal conductivity was observed for the 0.5% volume percentage in the liquid state while a ~53% enhancement in the solid state. Freezing and melting behaviour of water dispersed with graphene nanoplatelets were carried out using a cylindrical stainless steel capsule in a constant temperature bath. The bath temperatures considered for studying freezing characteristics were considered to be −6 °C and −10 °C, while to study the melting characteristics the bath temperature was set as 31 °C and 36 °C. The freezing and melting time decreased for all the test conditions when the volume percentage of GnP increased. The freezing rate was enhanced by ~ 43% and ~32% for the bath temperatures of −6 °C and −10 °C respectively at 0.5 vol % of graphene loading. The melting rate was enhanced by ~42% and ~63% for the bath temperature of 31 °C and 36 °C respectively at 0.5 vol % of graphene loading.

Bipolar plates significantly contribute in the development of the polymer electrolyte membrane (PEM) fuel cells technology due to their ability to produce high electrical conductivity based on type of materials used. Mismatching of inappropriate materials and manufacture may lead to the inferior performance of PEM fuel cells. Hence, material development was determined crucial to balance the overall performance of PEM fuels including the mechanical properties and electrical conductivity of the materials. Studies on conductive polymer composites (CPCs) offered filler orientation as an alternative method to enhance the overall performance of bipolar plate. Filler orientations permit an excellent conductivity network formation while controlling the filler alignment based on required applications. This paper reviewed various studies of filler orientations including materials used and methods of manufacture of CPC materials for the effective development of bipolar plate.

This study investigated the evolution of density, gas permeability and thermal conductivity of sugar maple wood during the thermo-hygro-mechanical densification process. The results suggested that the oven-dry average density of densified samples was significantly higher than that of the control samples. However, the oven-dry density did not show a linear increase with the decrease of wood samples thickness. The radial intrinsic gas permeability of the control samples was 5 to 40 times higher than that of densified samples, which indicated that the void volume of wood was reduced notably after the densification process. The thermal conductivity increased by 0.5 - 1.5% per percent increase of moisture content for densified samples. The thermal conductivity of densified wood was lower than that of the control samples. The densification time had significant effects on the oven-dry density and gas permeability. Both the densification time and the moisture content had significant effects on thermal conductivity, but their interaction effect was not significant.

In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

Electrically conductive adhesives (ECA’s) are used widely to replace or reinforce lead soldering or conductive metal components in electronic packaging applications such as die attachment, solderless interconnections, component repair, display interconnections, and heat dissipation. Their conductive behavior as well as the associated behaviors such as heat conduction and mechanical behavior (strength, rigidity, deformation and viscoelastic behavior, which may be affected by moisture ingression) are affected by adhesive film thickness, volume fraction, size and shape of the conductive filler, as well as uncured base adhesive viscosity, substrate and filler surface treatment and the applied pressure (during bonding and during conduction). The adhesive resistivity decreases precipitously above a characteristic filler volume fraction called the percolation threshold. In general, micron-sized metal fillers mixed in an adhesive (often an epoxy) resulting with different film thicknesses exhibit thickness thresholds for transition from three-dimensional conductivity to two-dimensional conductivity with considerable increases in thickness-direction (z-axis) resistivity when the film thicknesses are smaller than these threshold values. Recently, the use of conductive nanoparticles allowed decreases in percolation threshold levels as well as increases in mechanical strength and durability of ECA’s. Most ECA’s are supplied in liquid or paste form in varying viscosities and therefore, the method of their application also affects their performance. This work intends to provide an understanding of these effects on conduction behavior in (usually high-priced) equipment in which they are used.

In the present study, hypereutectic Al-Si alloy compacts and Al-Si/B4C composites were produced by conventional, microwave and spark plasma sintering techniques. The effects of sintering techniques and B4C particle addition on microstructural properties, density, hardness and electrical conductivity were investigated. The microstructures were examined with an optical microscope. Densities were measured using the Archimedes technique. Electrical resistance measurements were made with the four-point probe measurement technique. Elemental Al grains, master alloy grains and primary Si particles were determined in the microstructures of all samples. The addition of 15 wt% B4C caused the porosity rate to increase in the samples. Samples produced with SPS technique gave ≈80% higher hardness values than samples produced with CS and MWS. Compared to the samples produced with CS and MWS, the samples produced with SPS gave higher electrical conductivity values. Electrical conductivities were decreased as the weight percentage of B4C increased in all samples.

Struts of a superconducting YBa2Cu3Oy (YBCO) foam prepared by the infiltration growth method on the base of commercial polyurethane foams were extracted from the bulk, and thoroughly characterized concerning the microstructure and the magnetoresistance, measured by the four-point technique. Optical microscopy, electron microscopy, electron backscatter diffraction and atomic force microscopy observations indicate an unique microstructure of the foam struts which shows a large amount of tiny Y2BaCuO5 (Y-211) particles (with diameters between 50–100 nm) being enclosed in channel-like grain boundaries between the YBCO grains and an one-of-a-kind surface of the struts covered with Ba3Cu5Oy-particles. The resistance data obtained at temperatures in the range 4.2 K ≤T≤ 150 K (applied magnetic fields ranging from 0 to 7 T) were analyzed in the framework of the fluctuation-induced conductivity (FIC) approach using the Aslamazov-Larkin model. The resulting FIC curves reveal the presence of five distinct fluctuation regimes, namely, the short-wave (SWF), one-dimensional (1D), two-dimensional (2D), three-dimensional (3D), and critical (CR) fluctuation domains. The analysis of the FIC data enable the coherence length in the direction of the c-axis at zero-temperature (ξc(0)), the lower and upper critical magnetic fields (Bc1, Bc2), the critical current density at T= 0 K (Jc(0)) and several other parameters describing the the material’s superconducting properties to be determined. The present data reveal that the minuscule Y-211 particles found along the YBCO grain boundaries alter the excess conductivity and the fluctuation behavior as compared to conventional YBCO samples, leading to a quite high value for Jc(0) for a sample without added flux pinning centers.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

A study on the dependence of the thermal conductivity of the percolation network of carbon nanotubes (or CNTs) on the type and degree of functionalization has been carried out. The study was focused on the influence of the more commonly used -COOH, -OH and -СОNH2 groups. A non-linear dependence of the conductivity on the number of functional groups has been revealed. A small number of functional groups can improve conductivity, and a large one can impair it. We presuppose the existence of competing processes that increase thermal conductivity (changes in the CNT geometry, improvement of the contact between them) and enhance photon scattering (emergence of defects and scattering centers). The data can be used for controlling the thermophysical properties of the CNTs as well as determining the optimal degree of functionalization during the development of composites and nanodevices.

Hydraulic fracturing is an efficient method to develop oil/gas resources economically. Temporary plugging and diverting fracturing (TPDF) can generate diversion fractures perpendicular to the initial fractures and enhance the stimulated area. The aperture of the diversion fractures determines its conductivity and the oil/gas production. This work established a fluid-solid fully coupled simulation model to investigate the fracture aperture influenced by various factors during TPDF. The factors include the permeability of the tight plug, the length of the tight plug, Young’s modulus, rock tensile strength, in-situ stress contrast, the leak-off coefficient of the fracture surface, and fluid injection rate. Results show that the aperture of the previous fracture can be enlarged, and the aperture of the diversion fracture can be decreased by the tight plug. The aperture at the diversion fracture mouth is much smaller than that along the diversion fracture. Reservoirs with low Young’s modulus and high rock tensile strength can generate the diversion fracture with a wider aperture. Moreover, increasing the fluid injection rate can effectively increase the fracture mouth aperture. In this way, the risk of screenout can be lowered. This work is beneficial for the design of the TPDF and ensures safe construction.

Conversion of electromagnetic energy into magnetohydrodynamic energy occurs when the electric conductivity changes from negligible to finite values. This process is relevant during the epoch of reheating of the early Universe at the end of inflation and before the emergence of the radiation-dominated era. We find that conversion into kinetic and thermal energies is primarily the result of electric energy dissipation and that the magnetic energy plays only a secondary role in this process. This means that, since electric energy dominates over magnetic energy during inflation and reheating, significant amounts of electric energy can be converted into magnetohydrodynamic energy when conductivity emerges early enough, before the relevant length scales become stable.

CSZM compounds were synthesized by dry chemistry route with 5, 10, and 15% dopant of Mg dopants in the Ce 0.8-2x Sm 0.2 Zrx Mgx O2-d, {x = 0.05, 0.1 &0.15}. The newly investigated materials were physically, chemically, and electrochemically studied and have shown promising results. The CSZM was crystalized in a fluorite structure with a pure cubic phase in a space group Fm3m and cell parameter a = 5.401742 °A and theoretical density from 7.6 to 8.9 after firing in the air with a final temperature of 1400 °C. characterization of the structure and indexing of electrolyte materials were made after X-ray diffraction (XRD) testing. A Scanning electron microscope (SEM) morphological analysis was used to examine the microstructure details. Electronic impedance spectroscopy (EIS) measurements were achieved from 400 °C to 700 °C showing the highest value of conductivity of 1.0461 x 10+1 S/cm at 700 °C while the minimum value was 2.7329 x 10-2 S/cm at 400 °C and the total activation energy was found (Ea) 0.6865 eV under 5% H2/Ar.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

The electrokinetics methods have a great potential to characterize hydrogeological processes in geological media, especially in complex hydrosystems such as fractured formations. In this work, we conceptualize fractured media as a bunch of parallel capillary fractures following the fractal size distribution. This conceptualization permits to obtain analytical models for both the electrical conductivity and the electrokinetic coupling in water saturated fractured media. We explore two different approaches to express the electrokinetic coupling. First, we express the streaming potential coupling coefficient as a function of the zeta potential and then we obtain the effective charge density in terms of macroscopic hydraulic and electrokinetic parameters of porous media. We show that when the surface electrical conductivity is negligible, the proposed models reduces to the previously proposed one based on a bundle of cylindrical capillaries. This model opens up a wide range of applications to monitor the water flow in fractured media.

In this work, PMMA(Poly methyl methacrylate) microfluidic system was used as a micro-reactor for urea hydrolysis by urease enzyme with use conductivity principle and utilize sound level meter(SLM) App in smartphone as a novel detector by considering the peak height in the App as an indicate for urea concentration. the advantage of use small volume and how the reaction carried on in the microfluidic system with simple and low cost are discussed, and the results were analyzed and statically determine. The linearity, detection limit (3×noise )and Correlation Coefficient, 62.5-500 ppm, 31.25 ppm and 0.992 respectively also, recovery studied were between(98.5-100.13%).

A novel hybrid material based on Polyvinyl alcohol-Chitosan (PVA-Cs) was made, reinforced with conductive polymer fillers such as polypyrrole (PPy), Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS), carbon black (CB) and multi-wall carbon nanotubes (MW CNT). Our proposal is to use these fillers, which have not been studied in this context before, for obtaining composite materials, and to characterize them for the development of applications in microelectronics. FTIR analysis made evident the different func-tional groups present in the matrix and the fillers used. The use of quaternary mixtures (4 fillers) increased the contact angle, which increased the degree of hydrophobicity of the biocomposite. The Nyquist diagram of the analyzed samples showed a decrease in resistance and energy diffu-sion; the latter due to the transfer of electrons caused by the conductive polymers CB and the MWCNT. In the mechanical tension tests, Young's modulus values of 18.386 MPa were obtained, in contrast with the material matrix of PVA-Cs, which showed values of 11.628 MPa. Further-more, morphological analysis by SEM showed that the materials obtained were homogeneous, with no phase formation. The materials obtained showed higher electrical conductivity in the presence of the OH and NH2 groups, which could have possible applications in biopolymer elec-trodes.

Density Functional Theory (DFT) full potential linearized augmented plane wave (FP-LAPW) method with the Modified Becke-Johnson (mBJ) approximation is used to perform spin polarised calculations of the transition metal perovskites MoScO₃ and WScO₃. Both depict half metallic behaviour with semiconducting and metallic in the minority and majority spins respectively. MoScO₃ and WScO₃ have indirect R− Γ band gaps in the minority spin channels of 3.61 and 3.82eV respectively. Moreover, they both show substantial magnetic moments of 2.99μ_B. In addition, we calculate the dielectric function, optical conductivity and the optical constants, namely, the refractive index, the reflectivity, the extinction and absorption coefficients.

The phase composition design principle is introduced to obtain balanced properties of ionic conductivity and thermo-tolerant for zirconia solid electrolytes used in solid oxide fuel cells (SOFCs). The zirconia ceramic solid electrolytes are fabricated by two-step free sintering. With increasing Y/Mg ionic ratio from 1.78:1 to 1.88:1, the content of monoclinic phase fluctuates little (±3%). The ionic conductivity, including the total electrical resistance; grain electrical resistance and grain boundary electrical resistance at 1223K, are all gradually declining with the increasing of Y/Mg ionic ratio. Furthermore, the enrichment of Mg ion in grain boundary acts as a disincentive to grain boundary ionic conductivity. In addition, the maximum total equivalent conductivity at 1223K in this study reaches to 0.143 Scm-1 which can compare with that of certain YSZ. It will be beneficial to SOFCs application profited from increasing ionic conductivity of ceramic solid electrolytes.

As the interface between human and machine becomes blurred, hydrogel incorporated electronics and devices have emerged to be a new class of flexible/stretchable electronic and ionic devices due to their extraordinary properties, such as soft, mechanically robust and biocompatible. However, heat dissipation in these devices could be a critical issue and remains unexplored. Here, we report the experimental measurements and equilibrium molecular dynamics simulations of thermal conduction in polyacrylamide (PAAm) hydrogels. The thermal conductivity of PAAm hydrogels can be modulated by both the crosslinking density and water content in hydrogels. The crosslinking density dependent thermal conductivity in hydrogels varies from 0.33 to 0.51 Wm^-1K^-1, giving a 54% enhancement. We attribute the crosslinking effect to the competition between the increased conduction pathways and the enhanced phonon scattering effect. Moreover，water content can act as filler in polymers which lead to nearly 40% enhancement in thermal conductivity in PAAm hydrogels with water content vary from 23 to 88 wt%. Furthermore，we find the thermal conductivity of PAAm hydrogel is insensitive to temperature in the range of 25 ^oC – 40 ^oC. Our study offers fundamental understanding of thermal transport in soft materials and provides design guidance for hydrogel-based devices.

The nanocomposites with reversible cross-linking covalent bonds were prepared by reacting furfurylamine (FA)-modified diglycidyl ether of bisphenol A (DGEBA) and furfuryl-functionalized aniline trimer-modified graphene (TFAT-G) with bismaleimide (BMI) via Diels-Alder (DA) reaction. The successful synthesis of the TFAT modifier is confirmed by NMR hydrogen spectroscopy and IR spectroscopy tests. The structure and properties of TFAT-G epoxy nanocomposites are characterized by SEM, DSC, tensile and resistivity CES. The results show that TFAT-G was uniformly dispersed in the resin, and 1wt% TFAT-G composites increase to 233% for tensile strength, 63% for elongation at break, 66.1% for modulus and 7.8℃ for Tg. Overall, the graphene/self-healing resin nanocomposites have both good self-healing function and electrical conductivity by adding 1% modified graphene and still maintain the original 83% strength and 89% electrical conductivity after one cycle of heating repair.

Natural laterite fixed-bed column intercalated with activated carbon prepared from Balanites ae-gyptiaca (BA-AC) was used for As(III) removal from an aqueous solution. Investigations were carried out to solve the problem of column clogging which appears during water percolation through the column. Experimental tests were conducted to evaluate the hydraulic conductivity and the effects of various parameters such as grain size, bed height, and initial As(III) concentra-tion. The breakthrough increased from 15 to 85 h with the increase of the bed height from 20 to 40 cm, and decreased from 247 to 32 h with the increase of initial As(III) concentration from 0.5 to 2 mg/L. The permeability data showed that the fixed-bed column filled with laterites layers intercalated with activated carbon performs much better than the non-intercalated adsorbent col-umn. The Bohart-Adams model showed that increasing the bed height induced a decrease in kAB and N0 values. The critical bed depths determined using the bed depth service time (BDST) mod-el for As(III) removal were 15.23 and 7.98 cm for 1 and 20% breakthrough, respectively. The re-sults showed that the new low-cost filtration system, based on laterite layers alternated with BA-AC layers, could be used for the treatment of arsenic-contaminated water.

Electromagnetic (EM) waves, used for purposes such as geophysical characterization, impact properties to be measured. This paper describes the effects of radio frequency (RF) waves on the hydraulic conductivity of glass beads and natural sand. A series of tests were conducted using a customized, rigid-wall, cylindrical permeameter inside a resonant cavity made of Plexiglas covered with electrically conductive transparent films. Constant head ASTM-D2434 [1] tests were performed to measure the samples’ hydraulic conductivity. RF stimulation was performed using a magnetically coupled loop antenna at a constant frequency of 726 MHz and input power levels of 10, 25, 40, and 50 Watts. The hydraulic conductivity of both natural sand and glass-bead samples increased with RF stimulation. Furthermore, measurement of the electric-field component of RF waves was also performed to illustrate the pattern of the electric field as well as evaluate the RF impact on the hydraulic conductivity tests. The electric field was numerically simulated and validated against experimentally measured electric fields. A finite-difference numerical model was developed in MATLAB to analyze the seepage flow, which was then validated against the experimental results. An optimization scheme was then used to develop a governing equation for the RF impact on hydraulic conductivity.

The CuCrSn alloy is promising as high-strength and high-conductivity Cu alloy due to its relative low smelting requirement, while thus far reports on the CuCrSn alloy is still quite lacked. In this study, the microstructure and properties of Cu-0.20Cr-0.25Sn (wt%) specimens prepared under different rolling and aging combinations were comprehensively characterized, in order to reveal the effects of cold rolling and aging on the CuCrSn alloy. The results show that increasing the aging temperature from 400 ºC to 450 ºC can obviously accelerates the precipitation, and the cold rolling before aging significantly increases the initial microhardness and promotes the precipitation. Whereas, the deformation hardening will be eliminated during the aging process, making the microhardness even decrease monotonically when the aging temperature and the rolling ratio before aging are high. Performing the cold rolling after the aging can maximize the effects of precipitation strengthening and deformation strengthening, and its adverse impact on the conductivity is not serious. A tensile strength of 506.5 MPa and a conductivity of 70.33% IACS were obtained with such a treatment, only the elongation decreases. Different strength-conductivity combinations of the CuCrSn alloy can be achieved through appropriate combinations of the aging and post aging cold rolling conditions.

The current study aimed to evaluate the influence of different sintering temperatures on the properties of copper aluminum oxide (CuAlO₂) pellets synthesized from copper oxide (CuO) and aluminum hydroxide (Al(OH)₃) for application in smart infrastructure systems. The pellets were sintered at 400 K, 1000 K, and 1300 K, in the presence of nitrogen gas flow to reduce the amount of oxygen availability. The CuAlO₂ sintered nanoparticles were chemically analyzed by X-ray diffractometry, and the nanostructure of the materials was studied by scanning electron microscopy. The transmittance of the sintered materials was examined by ultraviolet/visible (UV/Vis) spectrophotometry, and 88% transparency was observed for the pellets sintered at 1300 K. Electrical conductivity was measured at 0.905 mS/cm, indicating a semiconducting behavior.

We confirm that energy dissipation weighting provides the most accurate approach to determining the effective hydraulic conductivity (Keff) of a binary K grid. A deep learning algorithm (UNET) can infer Keff with extremely high accuracy (R2 > 0.99). The UNET architecture could be trained to infer the energy dissipation weighting pattern from an image of the K distribution with high fidelity, although it was less accurate for cases with highly localized structures that controlled flow. Furthermore, the UNET architecture learned to infer the energy dissipation weighting even if it was not trained on this information directly. However, the weights were represented within the UNET in a way that was not immediately interpretable by a human user. This reiterates the idea that even if ML/DL algorithms are trained to make some hydrologic predictions accurately, they must be designed and trained to provide each user-required output if their results are to be used to improve our understanding of hydrologic systems most effectively.

Hydraulic conductivity is the key and one of the most uncertain parameters in groundwater modeling. The grid based numerical simulation require spatial distribution of sampled hydraulic conductivity at un-sampled locations in the study area. This spatial interpolation has been routinely performed using variogram based models (two-point geostatistics methods). These traditional techniques fail to capture the complex geological structures, provides smoothing effects and ignore the higher order moments of subsurface heterogeneities. In this work, a multiple-point geostatistics (MPS) method is applied to interpolate hydraulic conductivity data which will be further used in WASH123D numerical groundwater simulation model for regional smart groundwater management. To do this, MPS need ‘training images (TIs) as a key input. TI is a conceptual model of subsurface geological heterogeneity which was developed by using concept of ages, topographic slope as an index criteria and knowledge of geologist. After considerations of full physics of study area, an example shows the advantages of using multiple-point geostatistics compared with the traditional two-point geostatistics methods (such as Kriging) for the interpolation of hydraulic conductivity data in a complex geological formation.

Recently published structural analysis and galvanomagnetic studies of a large number of different bulk and mesoscopic graphite samples of high quality and purity reveal that the common picture assuming graphite samples as a semimetal with a homogeneous carrier density of conduction electrons is misleading. These new studies indicate that the main electrical conduction path occurs within 2D interfaces embedded in semiconducting Bernal and/or rhombohedral stacking regions. This new knowledge incites us to revise experimentally and theoretically the diamagnetism of graphite samples. We found that the $c$-axis susceptibility of highly pure oriented graphite samples is not really constant but can vary several tens of percent for bulk samples with thickness $t \gtrsim 30~\mu$m, whereas by a much larger factor for samples with smaller thickness. The observed decrease of the susceptibility with sample thickness resembles qualitatively the one reported for the electrical conductivity and indicates that the main part of the $c-$axis diamagnetic signal is not intrinsic of the ideal graphite structure but it is due to the highly conducting 2D interfaces. The interpretation of the main diamagnetic signal of graphite agrees with the reported description of its galvanomagnetic properties and provides a hint to understand some magnetic peculiarities of thin graphite samples.

Accumulative roll bonding (ARB) is one of methods of severe plastic deformation which is relevant for industrial production of sheets. While mechanical properties of several magnesium alloys subjected to ARB process have been studied, the physical properties have been reported only for some magnesium alloys. These properties are influenced by the texture developed during the ARB process and the temperature load. In the presented contribution, we studied thermal diffusivity and thermal conductivity of an AZ31 magnesium alloy after 1 and 2 passes through the rolling mill. Thermal diffusivity was measured with the laser-flash method in the temperature range between 20 and 350 °C. Thermal conductivity depends on the number of rolling passes. The microstructure and texture of sheets are significant factors influencing the thermal properties.

In this paper, the effect of microstructure on the thermal conductivity of plasma-sprayed Y₂O₃ stabilized ZrO₂ (YSZ) thermal barrier coatings (TBCs) is investigated. Nine freestanding samples deposited on aluminum-base superalloy are studied. Cross-section morphology such as pores, cracks, m-phase content, grain boundary density of the coated samples are examined by scanning electron microscopy (SEM) and electron back-scattered diffraction (EBSD). Multiple linear regressions are used to develop quantitative models which describe the relationship between the particle parameters, m-phase content and the microstructure such as porosity, crack-porosity, the length density of small-angle-crack and the length density of big-angle-crack. Moreover, the relationship between microstructure and thermal conductivity is investigated. Results reveal that the thermal conductivity of the coating is mainly determined by the microstructure and grain boundary density at room temperature (25 ℃) and by the length density of big-angle-crack, monoclinic phase content and grain boundary density at high temperature (1200 ℃).

Polymer nanocomposites are composed of polymer materials reinforced with nano fillers. In the present study the effective thermal conductivity of the composites filled with nanofillers has been investigated using commercially available finite element software ABAQUS 6.11. The nanofillers used were alumina particles and multi-walled carbon nanotubes (MWNTs) and the matrix was considered to be made of epoxy. For the analysis 2D and 3D Representative Volume Elements (RVEs) were generated using Random Sequential Adsorption (RSA) algorithm using MATLAB and Python scripts. Thermal conductivity was found out for 2D and 3D RVEs for different area and weight fractions respectively. Two different shapes of the alumina nanoparticles were considered: spherical (circular) and ellipsoidal (elliptical) for 3D (2D) analysis. It was found that the thermal conductivity was increased with the addition of nanofillers. The increase in thermal conductivity was approximately same for both types of inclusions at corresponding area or weight fractions in 2D or 3D analysis. The results showed that addition of MWNTs to the composites lead to a significant increase in thermal conductivity than spherical or ellipsoidal inclusions.

: Kentucky is one of the largest coal producing states and surface coal mining has led to changes in natural land cover, soil loss, and water quality. This study explored relationships between actively mined and reclaimed areas and vegetation change and water quality parameters. The study site evaluated 58 watersheds with Landsat-derived variables (reclamation age, mining percentage, reclaimed forest percentage, and reclaimed woods percentage) as well as topographic variables (such as elevation, slope, drainage density, and infiltration). Water samples were collected in spring (n=9), summer (n=14), and fall (n=58) 2017 to study changes in water quality variables (SO42-, alkalinity, conductivity, Ca2+, Mg2+, Mn2+, Al3+, and Fe2+,Fe3+) in response to changes in land cover. Pearson correlation analyses indicated conductivity has strong to very strong relationships with other variables of water quality variables related to coal mining (except Al3+, Fe2+,Fe3+, Mn2+, elevation, slope, and drainage density) and land cover variables. In addition, separate multivariate regression analyses were performed with conductivity values based on samples collected in the fall. First, conductivity response to mining percentage, reclamation age and topographic variables were examined (adjusted R2=0.818, p < 0.01). Next, vegetation cover change parameters were added to the same model, which yielded slightly improved R2 (adjusted R2 = 0.826, p < 0.01). Finally, reclamation age and mining percentage were used to explain the quantity of reclaimed forested areas as a percentage of watersheds. The model was significant (p < 0.01) with an adjusted R2 value of 0.641. Results suggest that the quantity (area as a percentage) of reclaimed forests may be a predictor of mining percentage and reclamation age. This study indicated that conductivity is a predictable water quality indicator that is highly associated with Coal Mine Related Stream Chemistry in areas where agriculture and urban development are limited. These findings may help the scientific community and key state and federal agencies improve their understanding of water quality attributes in watersheds affected by coal mining as well as refining land reclamation practices.

Hybrid organic/inorganic conducting and magnetic composites of core–shell type have been prepared by in-situ coating of nickel microparticles with polypyrrole. Three series of syntheses have been made. In the first, pyrrole was oxidized with ammonium peroxydisulfate in water in the presence of various amounts of nickel and the composites contained up to 83 wt% of this metal. The similar syntheses in 0.1 M sulfuric acid followed. Finally, the composites with polypyrrole nanotubes were prepared in water in the presence of structure-guiding methyl orange dye. FTIR and Raman spectroscopies confirmed the formation of polypyrrole. The resistivity of composite powders of the order of tens to hundreds Ω cm was monitored as a function of pressure up to 10 MPa. The resistivity of composites slightly increased with increasing content of conducting nickel. This apparent paradox is explained by the coating of nickel particles, which prevents their contacts and generation of metallic conducting pathways. Electrical properties were practically independent of the way of composite preparation or nickel fraction and were controlled by polypyrrole phase. On the contrary, magnetic properties were determined exclusively by nickel content. The composites were used as a solid phase to prepare a magnetorheological fluid. The test showed better performance when compared with a different nickel system.

The possibility of using graphane monolayer crystals as the electrode material is becoming popular. Graphane is stable at room temperature and has large surface area, but its chemical inertness hinders its direct interactions with Li ions. In this study, we performed density functional theory calculations to study the energetic stability, structural and electronic properties of Li on graphane with various CH divacancy configurations (v12, v13 and v14 ). The results show that adsorption of Li atom reduces the formation energy of the CH divacancy configurations. The Li-v12 is most stable with the highest binding energy of 3.25 eV/Li and relaxes to in-plane with other C atoms. Altering the Li charge state to have Li−1-v12 or Li+1 -v12 affects the energetic stability and electronic characters of Li-v12 . The Li−1-v12 (Li +1-v 12 ) enhances (reduces) the binding force between Li and v 12 configuration, and furthermore it improves (deteriorates) the conductivity of the structure. Further investigation of graphane with vacancies is encouraged due to these intriguing observations, as it holds promise for potential utilization as an electrode material.

The development of good conductivity p-type β-Ga2O3 is critical to realize its devices and applications. The nitrogen-doped p-type β-Ga2O3 films with enhanced conductivity characteristics were prepared through the thermal oxidation of GaN in the N2O atmosphere. Further measurements were performed on the oxidized films at 1000, 1050, and 1100 °C to have insight into the underlying mechanism of the thermally activated transformation process. The room temperature photoluminescence (PL) spectra demonstrated a moderate ultraviolet emission peak at 246 nm, confirming the generation of gallium oxide with a band gap of ~5.0 eV. The normalized X-ray diffraction (XRD), the high-resolution transmission electron microscopy (HRTEM), and the selected area electron diffraction (SAED) patterns were used to confirm the characteristic of polycrystalline and anisotropic growth. Then, the effects of the oxidation temperature on the amount of incorporated nitrogen were analyzed using secondary ion mass spectrometry (SIMS). Moreover, the ionization energy of the acceptor of films oxidized at 1000, 1050, and 1100 °C was calculated and analyzed using the temperature-dependent Hall test results. The results showed that nitrogen doping was the main contributor to p-type electrical properties. The activation energy of the polycrystalline β-Ga2O3 prepared through thermal oxidation of GaN in the N2O atmosphere was estimated to be 147.175 kJ·mol-1 using the Arrhenius plot, which was considerably lower than that of both dry and wet oxidations of GaN in O2 ambient, thus confirming the efficiency of thermal oxidation of GaN in N2O.

A novel manufacturing process is presented for producing Nano powders and thin films of CuCoO₂ (CCO) material. This process utilizes three cost-effective synthesis methods: hydrothermal, sol-gel, and solid-state reactions. The resulting delafossite CuCoO₂ samples were deposited onto transparent substrates through spray pyrolysis, forming innovative thin films with a Nano crystal powder structure. Prior to the transformation into thin films, CuCoO₂ powder was first produced using a low-cost approach. The precursors for both powders and thin films were deposited onto glass surfaces using a spray pyrolysis process, and their characteristics were examined through X-ray diffraction, scanning electron microscopy, HR-TEM, UV-visible, and Electrochemical impedance spectroscopy (EIS) analyses was conducted to determine the conductivity in transversal direction of this groundbreaking material for solar cell applications. On the other hand, the sheet resistance of the samples was investigated using the four probe-method to obtain the sheet resistivity and them calculate the in plane conductivity of the samples. We also investigated the aging characteristics of different precursors with varying durations. The functional properties of CuCoO2 samples were explored by studying chelating agent and precursor solution aging periods. Resuming, this study thoroughly discusses the synthesis of delafossite powders and their conversion into thin films, which hold potential as hole transport layers in transparent optoelectronic devices.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

We demonstrate that the conductivity of graphene on thin-film polymer substrates can be accurately determined by reflection-mode air-plasma-based THz time-domain spectroscopy (THz-TDS). The phase uncertainty issue associated with reflection measurements is discussed, and our implementation is validated by convincing agreement with graphene electrical properties extracted from more conventional transmission-mode measurements. Both the reflection and transmission THz-TDS measurements reveal strong nonlinear and instantaneous conductivity depletion across an ultra-broad bandwidth under relatively high incident THz electrical field strengths.

The conductor aluminum alloys Al-0.25wt.%Zr doped additionally with Х = Er, Si, Hf, and Nb were the objects of investigations. The fine-grained microstructure in the alloys was formed by Equal Channel Angular Pressing and Rotary Swaging. The thermal stability of the microstructure, specific electrical resistivity, and microhardness of the novel conductor aluminum alloys was investigated. The mechanisms of nucleation of the Al3(Zr,X) secondary particles during annealing the fine-grained aluminum alloys were determined using Jones-Mehl-Avrami-Kolmogorov equation. Using Zener equation, the dependencies of the mean secondary particle sizes on the annealing time were obtained on the base of analysis of the data on the grain growth in the aluminum alloys. The secondary particle nucleation during long-time low-temperature annealing (300 оC, 1000 hrs) was shown to go preferentially at the cores of the lattice dislocations. The Al-0.25%Zr-0.25%Er-0.20%Hf-0.15%Si alloy subjected to long-time annealing at 300 оC has the optimal combination of the microhardness and electrical conductivity (59.8%IACS, Hv = 480 ± 15 MPa).

The optoelectronic properties of free standing monolayer (ML) hexagonal boron nitride (h-BN) is investigated for potential solar energy conversion applications using the Density Functional Theory (DFT) full potential linearized augmented plane wave (FP-LAPW) method. In addition, the bulk optical properties have also been calculated for the sake of comparison. The dielectric functions, optical conductivities and the optical constants are evaluated using the relaxed structures from electronic total energy pseudopotential calculations. The results reinforce previous research on h-BN DUV optoelectronics and demonstrate the suitability of its use as a component in deep ultraviolet (DUV) and energy conversion devices.

Understanding the mechanism for heat tolerance is important for the hot pepper breeding program to develop heat-tolerant cultivars in changing climate. This study was conducted to investigate physiological and biochemical parameters related to heat tolerance and to determine leaf heat damage levels critical for selecting heat-tolerant genotypes. Seedlings of two commercial cultivars, heat-tolerant ‘NW Bigarim’ (NB) and susceptible ‘Chyung Yang’ (CY), were grown in 42 °C for ten days. Photosynthesis, electrolyte conductivity, proline content were measured among seedlings during heat treatment. Photosynthetic rate was significantly reduced in ‘CY’ but not in ‘NB’ seedlings in 42 °C. Stomatal conductivity and transpiration rate was significantly higher in ‘NB’ than ‘CY’. Proline content was also significantly higher in ‘NB’. After heat treatment, leaf heat damages were determined as 0, 25, 50 and 75% and plants with different leaf heat damages were moved to a glasshouse (30–32/22–24 °C in day/night). The growth and developmental parameters were investigated until 70 days. ‘NB’ was significantly affected by leaf heat damages only in fruit yield while ‘CY’ was in fruit set, number and yield. ‘NB’ showed fast recovery after heat stress compared to ‘CY’. These results suggest that constant photosynthetic rate via increased transpiration rate as well as high proline content in heat stress condition confer faster recovery from heat damage of heat-tolerant cultivars in seedlings stages.

Flexibility of polymers defined by an equation in 2019 is related here to thermal conductivity, using reliable data for both properties found in the literature. The resulting equation is simple, it has the form of a quadratic polynomial. The goodness of the fit represented by R² = 0.975, while R² = 1 represents a perfect fit. Thus, knowledge of one of these properties can be used for calculation of the other one. The present results are a part of a larger program enabling obtaining by calculation pertinent properties of polymers from other properties for which data are available.

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

In this paper, an icosahedral non – body centered model to simulate the periodic structure of homogeneous particulate composites, by predicting the particle arrangement, is presented. This model has yielded three different variations which correspond at three different deterministic particle configurations. In addition, the concept of boundary interphase between matrix and inclusions was taken into account. Thus, the influence of particle vicinity was examined in parallel with the interphase concept on the thermomechanical properties of the overall material. Next, by the use of this model the authors derived a closed – form expression to estimate the thermal conductivity of this type of composites. To test the validity of the model, the theoretical values arising from the proposed formula were compared with other theoretical predictions obtained from several accurate formulae found in the literature and an adequate accordance was observed.

Solvent-free, single-ion conducting electrolytes are sought after for use in electrochemical energy storage devices. Here, we investigate the ionic conductivity and how this property is influenced by segmental mobility and conducting ion number in crosslinked single-ion conducting polyether-based electrolytes with varying tethered anion and counter-cation types. Crosslinked electrolytes are prepared by the polymerization of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) methyl ether acrylate, and ionic monomers. The ionic conductivity of the electrolytes is measured and interpreted in the context of differential scanning calorimetry and Raman spectroscopy measurements. A lithiated crosslinked electrolyte prepared with PEG₃₁DA and STFSI monomers is found to have a lithium ion conductivity of 3.2 × 10^-6 and 1.8 × 10⁻⁵ S/cm at 55 and 100 °C, respectively. The percentage of unpaired anions for this electrolyte was estimated at about 23% via Raman spectroscopy. Despite the large variances in metal cation – STFSI binding energies as predicted via DFT and large variations in ionic conductivity, STFSI-based crosslinked electrolytes with the same charge density and varying cations (Li, Na, K, Mg, and Ca) were estimated to all have unpaired anion populations in the range of 19 to 29%.

Nanostructured materials have already become an integral part of our daily life. In many applications ion mobility decisively affects the performance of, e.g., batteries and sensors. Nanocrystalline ceramics often exhibit enhanced transport properties due to their heterogeneous structure showing crystalline (defect-rich) grains and disordered interfacial regions. In particular, anion conductivity in nonstructural binary fluorides easily exceeds that of their coarse-grained counterparts. To further increase ion dynamics aliovalent substitution is a practical method to influence the number of (i) defect sites and (ii) the charge carrier density. Here, we used high energy-ball milling to incorporate Y³⁺ ions into the cubic structure of SrF₂. As compared to pure nanocrystalline SrF2 the ionic conductivity of Sr_1-xYxF_2+x with x = 0.3 increased by 4 orders of magnitude reaching 0.8 x 10 ^-5 S/cm^-1 at 450 K. We discuss the effect of YF₃ incorporation on conductivities isotherms determined by both activation energies and Arrhenius pre-factors. The enhancement seen is explained by size mismatch of the cations involved, which are forced to form a cubic crystal structure with extra F anions if x is kept smaller than 0.5

A simple and effective surface modification of polyester fabrics with sulfuric acid to improve the interfacial deposition of polypyrrole was presented in our work. A range of sulfuric acid concentrations were analyzed by studying water contact angle. Effect of sulfuric acid modification on the deposition of polypyrrole was investigated by sheet resistance and color depth of fabric samples. Polyester fabrics coated with polypyrrole layer were confirmed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-Ray diffraction spectra (XRD), Fourier transform infrared spectroscopy (FTIR). XPS showed that sulphur containing functional groups were obviously appeared on the polyester fiber surface after modification, which were advantageous to promote the deposition of polypyrrole onto polyester fabrics. The improved deposition increased electrical conductivity of fabric samples.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

Magnetic permeability (μ), dielectric permittivity (ε) and electrical conductivity (σ) of the six elastomer samples obtained by mixing silicone rubber (RTV-530) with a kerosene-based ferrofluid in different volume fractions, φ: 1.31%, 2.59% and 3.84%, were determined using the complex impedance measurements, over the frequency range (500 Hz-2 MHz). Three samples (A0, B0 and C0) were manufactured in the absence of a magnetic field and the other three samples (Ah, Bh and Ch) in the presence of the magnetic field, H=43 kA/m. The component μ″ of the complex magnetic permeability of all samples presents a maximum, at a frequency fmax, which moves to higher values by increasing, φ, this maximum being attributed to Brownian relaxation processes. The conductivity spectrum, σ(f) for all samples, follows the Jonscher universal law, which allows both the determination of the static conductivity σDC, and the barrier energy of electrical conduction process, Wm. For the same φ, Wm is lower and σDC is higher in the samples Ah, Bh and Ch than in the samples A0, B0 and C0. The performed study is useful in manufacturing elastomers with predetermined properties and for possible applications, such as magneto-dielectric flexible electronic devices, which can be controlled by the volume fraction of particles or by an external magnetic field.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

The constant increase in current density in electrical wires leads to increasingly significant heat losses due to Joule effect. Therefore, reducing the electrical resistivity of copper wires becomes necessary. To achieve this goal, the development of a composite material incorporating a more conductive reinforcement, the graphene, is a promising way. The design of a copper/graphene composite using a powder metallurgy-based method is presented. This synthesis method allows for interface control through the growth of CuO(Cu) nanoparticles tightly bonded to the reinforcement. It also involves the dispersion of graphene through ultrasonic treatment and its alignment within the matrix using a uniaxial pressing densification method. The increase in the hardness (+12 HV) demonstrates the effective dispersion and separation of graphene layers. The impact on the electrical properties of dendritic copper (ρe = 2.30 µΩ.cm) remains limited, with a decrease in electrical resistance of approximately 1.4%. However, for copper with higher electrical resistivity, flake copper (at 2.71 µΩ.cm) and brass at (7.66 µΩ.cm), reductions of 2.7% and 10% have been achieved, respectively. With the improvement of graphene quality, there is more room to improve the electrical properties. This work paves the way for the development of composites with improved electrical resistivity.

This study presents an experimental investigation of the convective drying process of ginger rhizomes (Zingiber officinale). It analyses the effect of moisture content on the thermal properties of dried ginger rhizomes. Drying experiments were conducted under controlled conditions to establish the relationship between moisture content and thermal conductivity. The drying kinetics were examined to provide insights into the drying behaviour of ginger rhizomes and the influence of moisture content on their thermal properties. The results demonstrated a significant impact of initial moisture content and convective drying conditions on the drying process. As drying progressed, the moisture content decreased, leading to a reduction in thermal conductivity. It was observed that drying under convective drying takes 24 hours compared to open sun drying at nine days and solar tunnel drying at eight days. The drying temperature of 60°C was considered optimum. The results show that dried ginger at an absolute moisture content of 6.63% (wb) with a thermal conductivity of 0.0553W/m. K for unblanched ginger, 9.04% (wb) with thermal conductivity of 0.0516W/m. K for blanched ginger, 8.56% (wb) moisture content with a thermal conductivity of 0.0483W/m. K for peeled ginger and 5.98% moisture content with a thermal conductivity of 0.0460W/m. K for unpeeled ginger would be ideal for making powdered ginger rhizomes. These findings have practical implications for the food industry, as they can aid in designing and improving drying processes for ginger rhizomes and similar agricultural products. By understanding the relationship between moisture content and thermal properties, more efficient drying strategies can be developed to minimise energy consumption and maintain the quality of the dried product.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

The phenomena of electrical conductivity and electromigration in metallic systems are related, since in both cases the basic physical process is the scattering of conduction electrons by metal ions. Numerous searches have been made for equations connecting the conductivity with electromigration. In the case of a liquid metal, when using the Drude-Sommerfeld (DS) conduc-tivity equation, it was not possible to obtain a quantitative relationship between these phenomena, which would be correct. Attempts to find such a relationship when taking into ac-count the N. Mott correction (g - factor) in the DS equation were unsuccessful. This article proposes a different correction (b - factor) to the DS equation, which takes into account the pos-sibility of varying the momentum transferred by the conduction electron to a metal ion during the scattering. This correction allows to establish a quantitative relationship between conductivity and electromigration, as well as between electromigration in various binary systems with common components, in agreement with experiment. The proposed theory describes well, in particular, two- and multi-component metal systems of any concentration (the consistency rule for triangles A-B, B-C, C-A). The value of b - factor smoothly changes depending on the heat of vaporization of the metal, per unit volume.

The results of experimental studies of ohmic conductivity degradation in the ensembles of nanostructured anatase bridges under long-term effect of direct current are presented. Stochastic sets of interelectrode partially conducting bridges consisting of close-packed anatase nanoparticles were formed by the seeding particles from drying aqueous suspensions on the surfaces of silica substrates with interdigital platinum electrodes. Multiple-run experiments at room temperature have shown that ohmic conductivity degradation in these systems is irreversible. It is presumably due to accumulated capture of conduction electrons by deep traps in anatase nanoparticles. The scaling analysis of voltage drops across the samples at the final stage of degradation gives a critical exponent for ohmic conductivity as 1.597. This value satisfactorily agrees with the reported model data for percolation systems. At an early stage of degradation, the spectral density of conduction current fluctuations wihin the frequency range of 0.01 Hz - 1 Hz decreases approximately as , while near the percolation threshold the decrease trend changes to . This transition is interpreted in terms of an increasing contribution of blockages and subsequent avalanche-like breakdowns of part of the local conduction channels in the bridges into electron transport near the percolation threshold.

Knowing the spatial variability of factors that influence crop yield is essential to carry out a localized treatment. The present study aimed to map the spatial variability of apparent soil electrical conductivity (ECa) in two cultivation areas, delimit management zones (MZ), characterize the soil density (Sd) at two depths, in each MZ, and assess whether the delimitation of MZ, based on the spatial variability of ECa, was able to identify regions of the productive field with different Sd. Spatial variability of ECa was detected. MZ with the highest mean value of ECa also presented the highest mean values of Sd. The highest Sd values were observed for the 0.1 – 0.2 m layer, regardless of the studied area. Regardless of granulometry, the proposed method was able to detect density differences from ECa. The delimitation of MZ, based on the spatial variability of ECa mapping, was able to differentiate the mean values of Sd between MZ 1 (1.53 g cm-3) and MZ 2 (1.67 g cm-3) in the Area A, in the 0.1 – 0.2 m layer. A statistical difference was observed for the mean values of Sd, in MZ 1, layer 0.1 - 0.2 m, when comparing the two study areas: A (1.53 g cm-3) and B (1.64 g cm-3). We suggest that further studies should be carried out, as the mapping of the spatial variability of the apparent soil electrical conductivity showed potential in the differentiation of soil bulk density at different depths.

Over the years, leaked fluids from the aircraft caused severe deterioration of the airfield pavement. The combined effect of hot exhaust from the auxiliary power unit of military aircraft and spilt aviation oils caused rapid pavement spalling. If the disintegrated concreted pieces caused by spalling is sucked into the jet engine, it may cause catastrophic damage to the aircraft engine or physical injury to maintenance crews. This study investigates the effectiveness of incorporating hybrid fibres into ordinary concrete to improve the residual mechanical and thermal properties to prevent spalling damage of pavement. Three fibre reinforced concrete samples made with micro steel fibre and polyvinyl alcohol fibre with a fibre content of zero, 0.3%, 0.5% and 0.7% by volume fraction. These samples were exposed to recurring high temperature and aviation oils. Tests were conducted to measure the effects of repeated exposure on the concrete's mechanical, thermal and chemical characteristics. The results showed that polyvinyl alcohol fibre reinforced concrete suffered a significant loss of thermal properties and residual mechanical strength than the micro steel fibre reinforced concrete. However, hybrid fibre reinforced concrete performed better in retaining higher residual properties, and no spalling of concrete was observed.

Crystallization is a significant procedure in the manufacturing of many pharmaceutical and solid food products. In-situ Electrical Resistance Tomography (ERT) is a novel Process Analytical Tool (PAT) to provide a cheap and quick way to test, visualize, and evaluate the progress of crystallization processes. In this work, the spatial accuracy of the non-conductive phantoms in low conductivity solutions was evaluated. Gauss-Newton, Linear Back Projection, and iterative Total Variation reconstruction algorithms were used to compare the phantom reconstructions for tap water, industrial-grade saturated sucrose solution, and demineralized water. Cylindrical phantom measuring 10 mm in diameter and a cross-section area of 1.5 % of the total beaker area was detected at the center of the beaker. Two phantoms with a 10 mm diameter were visualized separately in non-central locations. The quantitative evaluations were done for the phantoms with radii ranging from 10 mm to 50 mm in demineralized water. Multiple factors such as ERT device and sensor development, FEM mesh density and simulations, image reconstruction algorithms, number of iterations, segmentation methods, and morphological image processing methods were discussed and analyzed to achieve spatial accuracy. The development of ERT imaging modality for the purpose of monitoring crystallization in low conductivity solutions was performed satisfactorily.

Metal oxide based electrodes play a crucial role in various as a transparent conductive oxide (TCO). One of the metal oxides, nickel oxide is a promising electrical conductive material. Here, we display that incorporation of vanadium in NiO lattice significantly improve both electrical conductivity and hole extraction. Also, vanadium doped nickel oxide exhibits a lower crystalline size compared to pristine nickel oxide, which maintains the reduction of surface roughness. These results indicating that the vanadium is an excellent dopant for NiO.

The molecular dynamics simulation has been used to investigate the structural and transport properties of (Ba_0.5-xSr_x)La_0.5InO_3-δ (x=0, 0.1, 0.2) oxygen-ion conductor. The previous studies reported that the ionic conductivity of Ba-doped LaInO3 decreases because Ba dopant forms narrow oxygen path in the lattice, which could hinder the diffusion of oxygen ion. In this study, we reveal the mechanism to improve the ionic conductivity by Ba and Sr co-doping on La site in LaInO3 perovskite oxide. The results show that the ionic conductivity of (Ba_0.5-xSr_x)La_0.5InO_3-δ increases with increasing numbers of Sr ions, which oxygen diffusion paths including Sr ion have larger critical radius than Ba ions. The RDF calculations showed the heights of peak in composition including Sr ions is lower and broaden, so oxygen ions moved easily into other oxygen sites.

Herein, we present preparation of solid polymer electrolyte (SPE) comprising of PEO, NaPF₆ and varying fraction of Succinonitrile (SN) by standard solution cast technique. The morphological features and structural properties were studied by the FESEM, XRD, respectively. FTIR was performed to study the interactions between polymer host, salt, and SN. Impedance spectroscopy, Transference number measurements, LSV and CV were used to examine the electrochemical properties. The complex permittivity/conductivity & modulus were studied to understand the dielectric properties by evaluating the dielectric strength, relaxation time, hopping frequency and dc conductivity. Based on the experimental results an interaction mechanism is presented.

In the last decade Electromagnetic Induction (EMI) measurements have been increasingly used for investigating the soil salinization caused by the use of brackish or saline water as irrigation source. EMI measurements proved to be a powerful tool for providing spatial information of the investigated soil because of the strict correlation between the output geophysical parameter, i.e. the electrical conductivity, to soil moisture and salinity. In addition, their non-invasive nature and their capability to collect a high number of data over broad areas and in relatively short time, makes these measurements attractive for monitoring flow and transport dynamics, otherwise undetectable with conventional measurements. In an experimental field, EMI measurements were collected during the growth season of the tomato, irrigated with three different irrigation strategies. The data were collected over three months in a time-lapse mode in order to visualize changes in electrical conductivity to be associated with soil salinity. A rigorous time-lapse inversion procedure has been set for modeling the soil salinization induced by brackish irrigation water.

Treatment wetlands (TWs) are Nature-Based Solutions increasingly used worldwide for wastewater (WW) treatment able to remove mineral and organic pollutants through both physical and biochemical process. Besides the reusable effluent, the TWs produce as main output plant biomass that need to be harvested and disposed at least once a year with significant management costs and TW temporary out of service. This study aims (i) to evaluate the potential of TWs biomass for local energy production and (ii) to understand TW hydraulic conductivity (Ks) effects on the biomass biomethane yield. Specifically, it was addressed by determining the Biochemical Methane Potential of common reed (CR) (Phragmites australis) samples collected at three harvest times from the 10-years-old horizontal subsurface treatment wetland (HSTW) used as a secondary WW treatment system for the IKEA® store located in Catania (Eastern Sicily, Italy). Furthermore, the falling head test was conducted to assess the hydraulic conductivity (Ks) variation in the HSTW, in order to understand the influence on the CR biomethane production. Average methane content values were 130.57 Nm3CH4/tVS (±24.29), 212.70 Nm3CH4/tVS (±50.62) and 72.83 Nm3CH4/tVS (±23.19) in August, September, October 2022, respectively. Ks was correlated with both dry matter (R2 = 0.58) and fiber content (R2 = 0.74) and, consequently, affected the biomethane yield that increased at the Ks increases (R2 = 0.30 in August, R2 = 0.57 in September). In the framework of a circular economy, results showed the successfully possibility of integrating the bioenergy production into TWs. The research could contribute (i) to encourage plant operators to reuse biomass from TWs for local energy production and (ii) to help plant operators to understand Ks effects on the biomass biomethane yield, in order to increase the sustainability of the system and to reduce the maintenance costs.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

Water is an essential commodity to sustain life. The condition of water in Tiruchirappalli was measured using different Physicochemical parameters like Temperature, pH, TDS, Total Solids, Salinity, Total Hardness, and Electrical Conductivity. Water samples were collected from different places in Tiruchirappalli city, Tamil Nadu. Water samples were examined by different chemical methods. According to the results, Thiruvarambur-1 showed comparatively higher results in the case of every parameter compared to other sampling stations. Obtained results were further interpreted using statistical tools. Considering ECs as a principal component for the regression and correlation analysis with other parameters significant correlation was found. A strong correlation was observed between ECs and TDS, Total Hardness, Turbidity, and Salinity.

Silver iodide (AgI) is a system prototype allowing the flow of ions through its structure and has a phase transition at 420 K, characterized by an abrupt change in conductivity and a high ionic conductivity. Introducing low concentrations of graphite (C) into the AgI structure produces a new material with a mixed conductivity (ionic and electronic) which increases with increasing temperature. The experimental results of the logarithm of the ionic conductivity as a function of the inverse of temperature for the (AgI)x–C(1−x) system for low carbon concentrations 0.97 ≤ x ≤ 0.99 were well fitted using a phenomenological model with a probability distribution for the charge carriers based on the carrier density

The system of non-interacting electrically charged core-massless spring-shell mechanical units, demonstrating negative effective mass, is considered, seen as a Drude-Lorentz gas. When such an ideal gas is exposed to the external harmonic field, it demonstrates as the certain conditions the negative frequency-dependent electrical conductivity. The negative value of the electrical conductivity implies that the electrical current will flow against the direction of the electric field and correspondingly the direction of the electrical force. Low- and high-frequency asymptotic behavior of the electrical conductivity is addressed. The same system demonstrates at low frequencies the negative asymptotic refraction. Experimental realization of the introduced model system, based on the exploitation of plasma oscillations of the free electron gas is suggested.

High temperature (HT) significantly affects the crop physiological traits and reduces the 12 productivity in plants. To increase yields as well as survival of crops under HT, developing heat13 tolerant plants is one of the main targets in crop breeding programs. The present study attempted 14 to investigate the linkage of the heat tolerance between the seedling and the reproductive growth 15 stages of tomato cultivars ’Dafnis‘ and ’Minichal’. This research was undertaken to evaluate heat 16 tolerance under two experimental designs such as screening at seedling stage and screening from 17 reproductive traits in greenhouses. Survival rate and physiological responses in seedlings of 18 tomatoes with 4-5 true leaf were estimated under HT (40 °C, RH 70%, day/night, respectively) and 19 under two control and HT greenhouse conditions (day time 28 °C and 40 °C, respectively). Heat 20 stress significantly affected physiological-chemical (photosynthesis, electrolyte conductivity, 21 proline) and vegetative parameters (plant height, shoot fresh weight, root fresh weight) in all 22 tomatoes seedlings. The finding revealed that regardless of tomato cultivars the photosynthesis, 23 chlorophyll, total proline and electrical conductivity parameters were varied in seedlings during the 24 heat stress period. The heat tolerance rate of tomatoes in the seedling stage might not be associated 25 always with reproductive parameters. HT reduced the fruit parameters likeas fruit weight (31.9%), 26 fruit length (14.1%), fruit diameter (19.1%) and fruit hardness (9.1%) in compared to NT under HT 27 in heat susceptible tomato cultivar ‘Dafnis’, while in heat tolerant cultivar ‘Minichal’ fruit length 28 (7.1%) and fruit diameter (12.1%) was decreased by the affect of HT but on the contrary fruit weight 29 (3.6%) and fruit hardness (8.3%) were increased. In conclusion, screening and selection for tomatoes 30 should be evaluated at the vegetative and reproductive stages with consideration of reproductive 31 parameters.

Soil hydraulic properties are often derived indirectly, i.e. computed from easily available soil properties with pedotransfer functions (PTFs), when those are needed for catchment, regional or continental scale applications. When predicted soil hydraulic parameters are used for the modelling of the state and flux of water in soils, uncertainty of the computed values can provide more detailed information when drawing conclusions. The aim of this study was to update the previously published European PTFs (Tóth et al., 2015, euptf v1.4.0) by providing prediction uncertainty calculation built into the transfer functions. The new set of algorithms was derived for point predictions of soil water content at saturation (0 cm matric potential head), field capacity (both -100 and -330 cm matric potential head), wilting point (-15.000 cm matric potential head), plant available water, and saturated hydraulic conductivity, as well as the Mualem-van Genuchten model parameters of the moisture retention and hydraulic conductivity curve. The minimum set of input properties for the prediction is soil depth and sand, silt and clay content. The effect of including additional information like soil organic carbon content, bulk density, calcium carbonate content, pH and cation exchange capacity were extensively analysed. The PTFs were derived adopting the random forest method. The advantage of the new PTFs is that they i) provide information about prediction uncertainty, ii) are significantly more accurate than the euptfv1, iii) can be applied for more predictor variable combinations than the euptfv1, 32 instead of 5, and iv) are now also derived for the prediction of water content at -100 cm matric potential head and plant available water content.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

Polymer composites with high thermal conductivity have a great potential for applications in modern electronics due to their low cost, easy process, and stable physical and chemical properties. Nevertheless, most polymer composites commonly possess unsatisfactory thermal conductivity, primarily because of the high interfacial thermal resistance between inorganic fillers. Herein, we developed a novel method through silver functionalized graphene nanosheets (GNS) and multiwalled carbon nanotube (MWCNT) composites with excellent thermal properties to meet the requirements of thermal management. The effects of composites on interfacial structure and properties of the composites were identified, and the microstructures and properties of the composites were studied as a function of the volume fraction of fillers. An ultrahigh thermal conductivity of 12.3 W/mK for polymer matrix composites was obtained, which is an approximate enhancement of 69.1 times compared to the polyvinyl alcohol (PVA) matrix. Moreover, these composites showed more competitive thermal conductivities compared to untreated fillers/PVA composites applied to the desktop central processing unit, making these composites a high-performance alternative to be used for thermal management.

This is the second of a two-paper series describing a multi-scale modeling approach developed to simulate crack sensing in polymer fibrous composites by exploiting interruption of electrically conductive carbon nanotube (CNT) networks. The approach is based on the finite element (FE) method. FE models at three different scales, namely the micro-scale, the meso-scale and the macro-scale, have been developed using the ANSYS PDL environment. In the present paper, the meso- and macro-scale analyses are described. In the meso-scale, a two-dimensional model of the CNT/polymer matrix reinforced by carbon fibers is used to develop a crack sensing methodology from a parametric study which relates the crack position and length with the reduction of current flow. In the meso-model, the effective electrical conductivity of the CNT/polymer computed from the micro-scale is used as input. In the macro-scale, the final implementation of the crack sensing methodology is performed on a CNT/polymer/carbon fiber composite volume using as input the electrical response of the cracked CNT/polymer derived at the micro-scale and the crack sensing methodology. Analyses have been performed for cracks of two different lengths. In both cases, the numerical model predicts with good accuracy both the length and position of the crack. These results highlight the prospect of conductive CNT networks to be used as a localized structural health monitoring technique.

We delve into the axion-dilaton model within the supergravity framework, with a specific focus on the intricacies of domain wall construction and stability. Employing holographic vitrification, we unravel the dynamics of domain wall formation in gauge theories featuring periodic vacuum structures. Our model, incorporating a QCD-like axion term and a stabilizing dilaton, undergoes scrutiny for conductivity variations under weak disorder. The investigation reveals the model's resilience, manifesting near-perfect conductivity under mild disorder conditions. However, the rigorous mathematical motivation for the holographic setup demands further elucidation. The scattered nature of our results prompts the necessity for a more systematic interpretation of QCD phenomena and conductivity transitions. This study contributes to the mathematical understanding of the axion-dilaton model's behavior, highlighting the imperative for a refined holographic framework and a more coherent interpretation of observed phenomena.

Due to the complexity of the microstructure of porous media, it is of great significance to explore the heat transport mechanism in porous media in many engineering applications. In this study, an expression for effective thermal conductivity（ETC） of porous media with randomly distributed damaged tree-like bifurcation networks is derived based on the theory of thermodynamics and fractal features of tree-like bifurcation networks. We investigate the effect of heat conduction and heat convection in porous media with randomly distributed damaged tree-like bifurcation networks on the ETC of the porous media. It is found that our fractal model is in good consistency with the existing available experimental data. In addition, the influence of the micro-structural parameters of the model on heat transfer in the porous media have been analyzed in detail. The research results can provide significant theoretical guidance for the development and design of heat transfer systems.

This article addresses the need to know the thermal conductivity in different filaments that this FDM technology uses. Because there are multiple applications that these additive manufacturing products play in the field of thermal insulation. For the study of thermal conductivity, the DTC-25 commercial conductivity measurement bench is used, where the tests will be carried out on a set of seven different materials with 100% fabrication density. From base materials such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA), materials of high mechanical and thermal resistance, polyether ether ketone (PEEK) and high-performance polyetherimide thermoplastic (ULTEM), to materials with metal inclusions (aluminum 6061) that would later be subjected to thermal aftertreatments. The study shows how the parts manufactured with aluminum inclusion have a higher thermal conductivity, 0.40 ±0.05 W/m·K, compared to another material, such as TPU, of high mechanical and thermal resistance, with a conductivity of 0.26 ±0.05 W/m·K.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

Low night temperature (LNT) can be a practical and economical target in tomato breeding programs in terms of energy saving in greenhouses. This study was conducted to investigate the physiological responses to LNT using four tomato accessions of cherry and large fruit types with LNT tolerance and sensitivity grown in two greenhouses with night temperature set-points of 10 and 15°C for heating. LNT significantly reduced plant height regardless of fruit types and LNT tolerance. The number of flowers were significantly reduced in 10°C in cherry but not in large fruit types. Fruit set in 10°C was significantly lower in LNT sensitive accessions than tolerant ones regardless of fruit types, which was due to abnormal flower morphology in 10°C. Proline accumulation patterns between 10 and 15°C significantly differed between fruit types as well as between LNT tolerant and sensitive accessions. Chlorophyll content in 10 °C was significantly higher at later growth stages in LNT tolerant accessions than sensitive ones in both fruit types. No clear difference in photosynthetic parameters was observed between fruit types or tolerance and sensitive accessions except for photosynthetic rate, which was significantly lower in tolerant than sensitive accessions during early growing period. These results suggest that different tomato fruit types may have different mechanisms for LNT tolerance.

Thermal interface material (TIM) that can exist as liquid at the service temperature enables efficient heat transfer across two adjacent surfaces in electronic applications. In this work, the thermal conductivities of different phase regions in the Ga-In system at various compositions and temperatures are measured for the first time. A modified comparative cut bar technique is used for the measurement of the thermal conductivities of In_xGa_1-x (x=0, 0.1, 0.214, 0.3, and 0.9) alloys at 40, 60, 80, and 100^oC that are the temperatures commonly encountered in consumer electronics. The thermal conductivity values for the liquid and semi-liquid (liquid+β) Ga-In alloys are higher than the TIM currently used in consumer electronics. These measured quantities, along with the available experimental data from the literature, served as input for the thermal conductivity parameter optimization using the CALPHAD (CALculation of PHase Diagram) method for the pure elements, solution phase, and two-phase region. A set of self-consistent parameters for the description of the thermal conductivity of the Ga-In system is obtained. There is good agreement between the measured and calculated thermal conductivity values for all the phases. Hence, it can be envisaged that liquid/semi-liquid Ga-In alloys can be considered as a potential TIM in consumer electronics due to its high thermal conductivity.

In the presented paper, a comprehensive study will be done on shape factor analysis of MoS2-GO in H2O-C2H6O2 based hybrid nanoliquids associated with effect and influence of transverse magnetic field and thermal radiation. The effect of variation in different parameters and nanoliquids shapes under temperature and velocity distribution is explored and also non-linear thermal radiation will be analyzed. Algorithms are introduced in proportion to mathematical modeling based on their numerical results and comparative curves for further explanation. In addition, it will be done research for influence and effect of new significant parameters emerged to the model to do sensitivity analysis and also their output results are demonstrated, examined and compared together by presenting graphs and tables. Based on detailed discussions, authentication of attained results designates the high accuracy of applied methods deployed to solve presented model in the paper. Our results satisfy that our used approach is accurate, highly reliable and also effective. All mentioned steps will be described throughout the literature.

The garnet Li₇La₃Zr₂O₁₂ (LLZO) has been widely investigated because of its high conductivity, wide electrochemical window and chemical stability to lithium metal. However, the usual preparation process of LLZO requires a long time of high-temperature sintering and a lot of mother powders against the lithium evaporation. The submicron Li₆.6La₃Zr₁.6Nb₀.4O₁₂ (LLZNO) powders are prepared by conventional solid-state reaction method and attrition milling process, which are stable cubic phase and have high sintering activity, and Li stoichiometric LLZNO ceramics are obtained by sintering at a relative lower temperature or for a short time by using these powders which are difficult to control under high sintering temperature and long sintering time. The particle size distribution, phase structure, microstructure, distribution of element, total ionic conductivity, relative density and activation energy of submicron LLZNO powders and LLZNO ceramics are tested and analyzed by laser diffraction particle size analyzer, XRD, SEM, EIS and Archimedean method. The total ionic conductivity of sample sintered at 1200 °C for 30 min is 5.09 × 10-4 S·cm-1, the activation energy is 0.311 eV, and the relative density is 87.3%, and sintered at 1150 °C for 60 min total ionic conductivity is 3.49 × 10-4 S·cm-1, the activation energy is 0.316 eV, and the relative density is 90.4%. At the same time, all-solid-state batteries are assembled with LiMn₂O₄ as positive electrode and submicron LLZNO powders as solid state electrolyte. After 50 cycles, the discharge specific capacity is 105.5 mAh/g and the columbic efficiency is above 95%.

The objective of this study was to investigate successional changes in water flow as a result of changes in soil hydraulic properties after crop abandonment under drought and non-drought conditions, and under water uptake by co-occurring perennial plant species to clarify the observation that typical perennial grass species are seldom observed in abandoned fields. Soil hydraulic properties were measured in croplands which had been abandoned for different periods (2, 9, and 18 years from abandonment) and in a grazed grassland site. Hydrological processes in the soil profiles were simulated with soil hydraulic properties under drought and non-drought summer conditions with water uptake from perennial grass species Suction in the surface soils increased with the period of abandonment, with this trend being particularly obvious in a drought year. Available water appears to be restricted in the later successional stage of abandoned fields and in grazed grassland for plants that have drought tolerance. Dry soil and climate conditions are important factors determining the intrusion of the typical perennial grass, S. krylovii, into degraded abandoned fields. This abiotic interaction between soil hydraulic properties and climate conditions may play an important role for plant succession in abandoned cropland.

The optical conductivity in the charge order phase is calculated in the extended Hubbard model describing an organic Dirac electron system α-(BEDT-TTF)₂I₃ using the mean field theory and the Nakano-Kubo formula. A peak structure due to interband excitation being characteristic in two-dimensional Dirac electron system is found above the charge order gap. It is shown that the peak structure originates from the Van Hove singularities of the conduction and valence bands, where those singularities are located at a saddle point between two Dirac cones in momentum space. The frequency of the peak structure exhibits drastic change in the vicinity of the charge order transition.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Redox-flow batteries are rechargeable batteries that store energy in two liquid electrolytes, separated by a membrane. During charging and discharging, the electrolytes flow through the membrane and undergo chemical reactions that generate or consume electrical energy. These batteries are known for their scalability and long cycle life and are versatile energy storage technologies developed to enhance efficiency and lower costs. Deep Eutectic Solvents (DES) are eco-friendly alternatives to traditional electrolytes, and their properties have been studied to improve the performance of redox-flow batteries. We investigated choline chloride/ethylene glycol (ChlCl/Eg) mixtures with LiPF6 salt at four concentrations through experimental and MD simulations. The thermophysical and transport properties of the mixture, including density, diffusion coefficient, viscosity, and ionic conductivity, were calculated across a temperature range of 298.15–398.5 K. Our findings indicate that an increase in salt concentration leads to a decrease in diffusion coefficients and ionic conductivity, while increasing the viscosity of the deep eutectic solvent. This research provides valuable insights into the behavior of DES mixtures and can aid in the design and optimization of DES-based processes for use in redox-flow batteries.

The efficiency, durability, and overall performance of a car engine are influenced by several critical factors. The quality and properties of engine oil play a crucial role, and oil is used in internal combustion engines for lubrication and cooling purposes. This research study aimed to compare the impact of fullerene-C60 (99.5%), Fe2O3, and TiO2 nanoparticles on the thermal properties of C.A.L.T.E.X. red engine oil with grades 10W30, 20W40, and 20W50. This study focused on the effect of a nanoparticle concentration of 0.01 wt.% in different engine oil grades at various temperature values of 30-120 ℃. The Nanofluids were prepared using the two-step direct mixing method, employing a magnetic stirrer and an ultrasonicator, ensuring uniform distribution of nanoparticles in the base fluids. The thermal conductivity, thermal diffusivity, and volumetric heat capacity of the base fluids and nanofluids were measured using the FLUCON LAMBDA thermal conductivity meter. Additionally, flash points were measured using the flash point tester. It was concluded that the thermal properties of TiO2 and Fe2O3 showed considerable enhancement; in contrast, Fullerene only showed the 212 ℃ flash point.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.