The experimental results of forces and efforts derived from the opening of incisions in the orbital cavity in a pig’s head are presented in this article. The different areas of the incision openings are related to the needs at the incision procedure for a dacryocystorhinostomy. In terms of the experimental procedure, an origin and a plane are defined so as to allow the location of the opening of the incision. The incisions are retracted along an axis of said origin. This procedure has been based on the mathematical model developed for this work, which consists of a procedure for determining the behavior of an incision when a force is applied to retract the skin. The experimental data obtained, suggests the existence of an almost linear relationship between the increment of resistance in relation to the time obtained for each opening, the same of which is deemed to be consistent with the behavior of an elastic material.

Coccidioides spp are thermally dimorphic fungi found in geographically defined areas of the Western Hemisphere. The primary portal of entry is respiratory, with a symptomatic pneumonic disease as the most common presentation. Subsequent pulmonary complications as well as extrapulmonary metastatic infection may occur, either of which may be the presenting disease manifestation. Cavitary lung disease may be found incidentally or when investigating symptoms such as cough or hemoptysis. This study aims to explore the spectrum of coccidioidal cavities and the evaluation and management in a cohort of patients seen at Kern Medical over the last 12 years.

The ability to control the flow of quantum information deterministically is useful for scaling up quantum computation. In this paper, we demonstrate a controllable quantum switchboard which directs the teleportation protocol to one of two targets, fully dependent on the sender’s choice. The quantum switchboard additionally acts as a optimal quantum cloning machine. We also provide a physical implementation of the proposal using a coupled-cavity array. The proposed switchboard can be utilized for the efficient routing of quantum information in a large quantum network.

Alveolar soft part sarcoma (ASPS) is a rare mesenchymal neoplasm. It affects young adults more and occurs more frequently in the extremities. ASPS is exceedingly rare in the nasal cavity. We report a case of ASPS in the nasal cavity of a 17-year-old female. Its most striking features included organoid and pseudoalveolar arrangement of tumor cells, which were large and polygonal, with vesicular nuclei and abundant eosinophilic cytoplasm rich in granules. There were PAS-positive, diastase-resistant crystalline rods within the cytoplasm. Our case displayed inapparent pseudoalveolar growth pattern and frank pleomorphism. The diagnosis of ASPS, which presents uncommon morphologic findings in unusual sites, is challenging. Recognition of ASPS is greatly assisted by attention to its characteristic cytological features, including intracytoplasmic crystals and immunohistochemistry showing absence of skeletal muscle, epithelial, and neuroendocrine markers.

In birds, unlike mammals, there is no complete separation between the thoracic and abdominal cavities. Instead, they have the coelomic cavity where most main organs are found. Therefore, an adequate knowledge of the anatomy of the coelomic cavity is of great importance for veterinarians, biologists and the scientific community. This study aimed to evaluate the coelomic cavity anatomy in the Atlantic puffins (Fratercula Arctica) using anatomical sections and computed tomography images.

Registration of the flow pattern fine structure and the matter distribution of a free falling liquid drop in a target fluid at rest in the impact mode of coalescence, when the kinetic energy of the drop exceeds its available potential surface energy (APSE), was carried out by photo and video recording. The main attention was paid to the study of the flow structure at the initial stage of the cavity formation. To carry out color registration, the flow pattern was illuminated by several matrix LED and fiber optic sources of constant light. The planning of experiments and interpretation of the results were based on the properties of the complete solutions of the fundamental equations of fluid mechanics system, including the transfer and conversion of energy processes. Complete solutions of the system of equations describe large-scale flow components that are waves or vortices as well as thin jets (ligaments, filaments, fibers, trickles). In experiments, the jets are accelerated by the converted available potential surface energy (APSE) when the free surfaces of merging fluids were eliminated. The experiments were performed with the coalescence of water, solutions of alizarin ink, potassium permanganate, copper sulphate or iron sulphate drops in deep water. In all cases, at the initial contact, the drop begins to lose its continuity and breaks up into a thin veil and jets, the velocity of which exceeds the drop contact velocity. Small droplets, the size of which grows with time, are thrown into the air from spikes at the jet tops. On the surface of the liquid, the fine jets leave colored traces that form linear and reticular structures. Part of the jets penetrating through the bottom and wall of the cavity forms an intermediate covering layer. The forming layer jets are separated by interfaces of the target fluid. The processes of molecular diffusion equalize the density differences and form an intermediate layer with sharp boundaries in the target fluid. All noted structural features of the flow are also visualized when a fresh water drop isothermally spreads in the same tap water. The fast-changing and finely structured diffuse boundary of merging fluids, which at the initial stage has a complex and irregular shape, is gradually smoothed out by molecular diffusion processes. The similar flow patterns were observed in all performed experiments, however the geometric features of the flow depend on the individual thermodynamic and kinetic parameters of the contacting fluids.

The magnetic heating effect for the superconducting quarter-wave resonator (QWR) cavities is investigated, and the Q slopes of the superconducting cavities are measured with an increasing accelerating field. Physical phenomena for zero-temperature limit are introduced. Bardeen–Cooper–Schrieffer (BCS) resistance and Casimir force are calculated for the zero-temperature limit. The vertical test is shown for the performance test of the quarter-wave resonator (QWR) cavities. The parameters for the quarter-wave resonator (QWR) cavity are presented. The Q slopes are measured as a function of an accelerating electric field at 4.2 K. The surface resistance of the superconducting cavity increases with an increasing peak magnetic field. The magnetic defects cause the degradation for the quality factor. From the magnetic degradation, we can find the magnetic moments of the superconducting cavities. All the quarter-wave resonator (QWR) cryomodules are installed in the tunnel, and beam commissioning is performed successfully.

Background. Restoring large defects with proximal caries extending below the cemento-enamel junction and cavity margins located beneath the gingival tissues represents a very common clinical situation. The aim of this article is to propose a clinical classification of the localization subgingival margins of cavity.Material and methods. Diagnosis is carried out by periodontal probe perpendicular to the long axis of the tooth in the deepest point of the cavity’s margin. To describe the localization subgingival margins of cavity we use exponent which value is equal to the distance (integer number expressed in millimeters) of the level of epithelial attachment to the margin of the cavity. Three periodontal examiners, with >10 years of periodontal practice, were required to attend a calibration session aimed at the validation of the proposed classification. Results. The intrarater and interrater agreement among the localization subgingival margins of cavity: for intrarater agreement ranged from 0.74 to 0.95 (almost perfect agreement), whereas interrater agreement ranged from 0.26 to 0.59 (moderate agreement).Conclusions. The classification the localization subgingival margins of cavity is useful for reaching a more precise diagnosis.

For applications in sensing and cavity-based quantum computing and metrology, open-access Fabry-Perot cavities – with an air or vacuum gap between a pair of high reflectance mirrors – offer important advantages compared to other types of microcavities. For example, they are inherently tunable using MEMS-based actuation strategies, and they enable atomic emitters or target analytes to be located at high field regions of the optical mode. Integration of curved-mirror Fabry-Perot cavities on chips containing electronic, optoelectronic, and optomechanical elements is a topic of emerging importance. Micro-fabrication techniques can be used to create mirrors with small radius-of-curvature, which is a prerequisite for cavities to support stable, small-volume modes. We review recent progress towards chip-based implementation of such cavities, and highlight their potential to address applications in sensing and cavity quantum electrodynamics.

We introduce a model of a passive optical cavity based on the two-dimensional Lugiato-Lefever equation, with a localized pump carrying intrinsic vorticity S, and the cubic or cubic-quintic nonlinearity. Up to S = 5, stable vortex-ring states (vortex pixels) are produced by a variational approximation and in a numerical form. Surprisingly, vast stability areas of the vortex states are found, for both the self-focusing and defocusing signs of the nonlinearity, in the plane of the pump-strength and loss parameters. When the vortex-rings are unstable, they are destroyed by azimuthal perturbations which break the axial symmetry. The results suggest new possibilities for mode manipulations in nonlinear optical media.

Obstructive Sleep Apnea (OSA) surgery is now a viable solution in selected patients and the “remodelling” palatopharyngeal surgery is the most common one. Recently it becomes less in-vasive with the introduction of Barbed Sutures (BS). An optimization of surgical technique is represented by Barbed pharyngoplasty (BP), that requires surgical precision and needs efficient and precise oropharyngeal visualization. Consequently, the lighting system is of pivotal im-portance in BP. The aim of this work is to describe the first experience on the use of a new light-ing system, called KlaroTM in BP for OSA. We evaluated the Klaro™ system in 15 consecutives BP for OSA in comparison with conventional headlamp illumination. The visualization of pala-topharyngeal muscle in the bottom of the tonsillar fossa, entry and exit needle, such as needle tip were statistically better with KlaroTM than headlamp illumination both for surgeon and resi-dent (p<0.05). No significant differences for the visualization of the posterior pharyngeal wall and uvula were reported. The KlaroTM lighting system allows a satisfied illumination of oral cavity and oropharynx in the majority of cases. We encourage to use of KlaroTM not only in BP for OSA, but also in all oral and pharyngeal surgeries, including tonsillectomy and oncological surgery.

The sinking of cavities in urban areas is a very important geological risk to which many towns in Puglia are exposed. The study, mapping, geological and speleological description, classification and cataloging of forms and types of cavities is of fundamental importance for each urban center because it is linked to past local anthropic and natural processes, unique to each site. All this could lead to an enhancement of existing underground cavities in urban areas through conservation and continuous monitoring. Unfortunately in many cases these underground cavities have been used as landfills and subsequently abandoned. One of these cavities at the end of March 2007 collapsed in the inhabited center of Gallipoli causing damage to the structures and fortunately not to human lives. In the area relating to the collapsed cavity, a series of geophysical investigations were undertaken with the use of ground penetrating radar methodology in an attempt to delimit the area of collapse and understand the possible types of interventions for restoring the area. In the same area the measures were repeated 16 years later (December 2022) due to another collapse. The results show a much more widespread danger situation.

The human oral microbiome refers to an ecological community of symbiotic and pathogenic microorganisms found in the oral cavity. The oral cavity is a suitable environment that provides various kinds of biological niches such as teeth, tongue, and oral mucosa. The oral cavity is the gateway between the external environment and the human body, maintaining oral homeostasis, protecting the mouth, and preventing disease. On the flip side, the oral microbiome plays an important role in triggering, development, and progression of oral and systemic diseases. Currently, disease diagnosis through the analysis of the human oral microbiome has been realized with the recent development of innovative detection technology, and is overwhelmingly promising compared to the previous era. It has been found that patients with oral diseases and systemic diseases have variations in the oral microbiome compared to normal subjects. This narrative review provides insight into the pathophysiological role that oral microbiome plays in influencing oral and systemic diseases, and updates the knowledge related to the oral microbiome over the past 30 years. A wide range of updates was provided with the latest knowledge of the oral microbiome to help researchers and clinicians in both academic and clinical aspects. The microbial community information can be utilized in non-invasive diagnosis and help develop a new paradigm in precision medicine, which will benefit human health in the era of post-metagenomics.

Increasing the quality factor (Q) of an optical resonator device has been a research focus to be utilized in various applications. Higher Q-factor means light is confined in a longer time which will produce a shaper peak and higher transmission. In this paper, we introduce a novel technique to increase further the Q-factor of a one-dimensional photonic crystal (1D PhC) cavity device by using an end loop-mirror (ELM). The technique utilizes and recycles the light transmission from the conventional 1D PhC cavity design. The design has been proved to work by using the 2.5D FDTD simulation with Lumerical FDTD and MODE softwares. By using the ELM technique, the Q- factor of a 1D PhC design has been shown to have increased up to 79.53 % from the initial Q value without the ELM. This novel design technique can be combined with any high Q-factor and very high Q-factor designs to increase more the Q-factor value of a photonic crystal cavity devices or any other suitable optical resonator devices. The experimental result shows that the device is measurable by adding a Y-branch component to the one-port structure and able to get the high-Q result.

Quantum noise limits the sensitivity of laser interferometric gravitational-wave detectors. Given the state-of-the-art optics, the optical losses define the lower bound of best possible quantum-limited detector sensitivity. In this work, we come up with the configuration which allows to saturate this lower bound by converting the signal recycling cavity to be a broadband signal amplifier using an active optomechanical filter. We will show the difference and advantage of such a broadband signal recycling scheme compared with the previous white-light-cavity scheme using the optomechanical filter in [Phys.Rev.Lett.115.211104 (2015)]. The drawback is that the new scheme is more susceptible to the thermal noise of the mechanical oscillator. To suppress the radiation pressure noise which rises along with the signal amplification, squeezing with input/output filter cavities and heavier test mass are used in this work.

The study utilizes the energy-flux-vector method to analyze the heat transfer characteristics of natural convection in a wavy-wall porous square cavity with a partially-heated bottom surface. The effects of the modified Darcy number and modified Rayleigh number on the energy-flux-vector distribution and mean Nusselt number are examined. The results show that when a low modified Darcy number with any value of modified Rayleigh number is given, the recirculation regions are not formed in the energy-flux-vector distribution within the porous cavity. Therefore, a low mean Nusselt number is obtained. The recirculation regions do still not form and thus the mean Nusselt number has a low value when a low modified Darcy number with a high modified Rayleigh number is given. However, when the values of the modified Darcy number and modified Rayleigh number are high, the energy flux vectors generate recirculation regions and thus a high mean Nusselt number is obtained.

Computational Fluid Dynamics (CFD) is utilized to study entropy generation for the rarefied steady state laminar 2-D flow of air-Al2O3 nanofluid in square cavity equipped with two solid fins at the hot wall. Such flows are of great importance in industrial applications, such cooling of the electronic equipment’s and nuclear reactors. In the current study, effects of Knudsen number (Kn), Rayleigh number (Ra) and the nano solid particles volume fraction (ϕ) on the entropy generation are investigated. The values of parameters considered in this work are as follows: 0≤Kn≤0.1, 〖10〗^3≤Ra≤〖10〗^6,0≤ϕ≤0.2. Length of the fins (LF) is considered to be fixed and equals to 0.5 m, whereas the location of the fins with respect to the lower wall (HF) is set to 0.25 and 0.75 m. Simulations demonstrate that there is an inverse direct effect of Kn on the entropy generation. Moreover, it is found that when Ra is less than 104, the entropy generation, due to the flow, increases as ϕ increases. In addition, the entropy generation due to the flow will decrease at Ra greater than 104 as ϕ increases. Moreover, the entropy generation due to heat will increase as both the ϕ and Ra increase. In addition, a correlation model of the total entropy generation as a function of all of the investigated parameters in this study is proposed. Finally, an optimization technique is adapted to find out the conditions at which the total entropy generation is minimized

We describe the effect of the expansion of space on the wavelength of the light beam in a Fabry-Pérot interferometer. For an instrument such as the Laser Interferometer Gravitational-Wave Observatory (LIGO), which has high sensitivity and a long period of light storage, the wavelength ${\lambda }_L$ of laser photons are redshifted due to the expansion of space in each cavity by an amount $\delta \lambda$ given by $\delta \lambda /{\lambda }_L=H_0{\tau }_s\approx 8.8\times {10}^{-21}$ , where $H_0\approx 2.2\times {10}^{-18}{\mathrm{s}}^{-1}$ is the Hubble constant and ${\tau }_s\approx 4\mathrm{ms}$ is the light storage time for the cavity. Since ${\tau }_s$ is based on the cavity finesse $\mathcal{F}$ which depends on the laser beam full width at half maximum (FWHM) $\delta \omega$ of each cavity, we show that a difference in finesses between the LIGO arm cavities produces a signal $h_H\left(t\right)$ at the anti-symmetric output port given by $h_H\left(t\right)=2a_1{H}_0\left(\frac{1}{\delta {\omega }_X\left(t\right)}-\frac{1}{\delta {\omega }_Y\left(t\right)}\right),$ where $\delta {\omega }_X\left(t\right)$ and $\delta {\omega }_Y\left(t\right)$ are the beam FWHM at time t, respectively, for the X and Y arm cavities and $a_1$ is a beam proportionality constant to be determined expermentally. Assuming $a_1\approx 1$ , then for cavity beams FWHM of $\delta \omega \left(t\right)\approx (523.2\pm 31)\mathrm{rad}.{\mathrm{s}}^{-1}$ the output signal has the range $\mid h_H\left(t\right)\mid \le 1\times {10}^{-21}$ , which is detectable by advanced LIGO.

Abstract: More than 40 hypotheses predict associations between features of nest architecture and at least one measure of reproductive success. However, quantitative studies of reproductive consequences of nest characteristics remain scarce. In addition, most studies were conducted on model species of which nests can be easily monitored with artificial nest-boxes. Here we review the replicability of research protocols and findings in model species with many repeat studies focusing mainly on nest-size components, animal-derived nest material, or fresh greenery in blue tits (Cyanistes caeruleus), great tits (Parus major), tree swallows (Tachycineta bicolor), and starlings (Sturnus spp.). The studies looked for correlations between nest traits and aspects of breeding performance that can be easily quantified in the field, such clutch size, brood size at hatching or fledging, the % of eggs that hatch or fledge, or nestling characteristics assumed to reflect qualities associated with survival probabilities (e.g., morphometry, body condition, blood profiles). We discuss the consequences of poor replicability of research methodologies and provide explanations for why many of these studies reported poor associations between nest design and breeding success at different spatiotemporal scales. We also make suggestions for future research. Keywords: Nest design, Breeding success, Nest-box, Cavity-nesting birds, Replicability

Backgroumd: The feeling of nasal obstruction is one of the most complaints of the Ear Nose and Throats (ENT) patients. The reason of this complaint is variable, such as Nasal Septal Deviation (NSD). NSD is a significant obstacle to normal respiration and the volume of air entering the lungs. Understanding how the deviation causes the obstruction is so important, because it leads to better management of this disease. Rhinomanometry and acoustic rhinometry are methods that are used for objective evaluation of upper airway, but they are semi invasive and the accuracy are not guaranteed. With development of Computed Tomography (CT scan) and Computational Fluid Dynamics (CFD), numerical studies on airflow in different parts of the nasal cavity have been performed. Objectives: The purpose of this study was to compare nasal airflow patterns between patient with NSD and healthy nasal cavity using a computational fluid dynamics (CFD) Methods: A patient with NSD and a healthy human were selected. Using CFD, the maximal airflow velocity, nasal resistance, maximal Wall Shear Stress (WSS), and pressure drop in bilateral nostrils of both cases were assessed. Results: Pressure and velocity profiles are evaluated at a mass flow rate of 17.4 Liters Per Minute (LPM). The velocity profile shows an abnormal flow profile in the septal deviated nasal cavity and the peak velocity is observed at the middle nasal region, whereas this point is at the nasal valve level in a healthy nasal cavity. Wall shear stress (WSS) caused by NSD is lower than in normal nasal cavities. The pressure drop in a nasal cavity with deviated septum is higher than in a healthy nasal cavity. Based on the results of this investigation nasal resistance in NSD was higher than in normal, healthy nasal cavity. Conclusions: NSD plays an important role in nasal airflow regime and it results in the feeling of obstruction comparing to normal nasal cavity. Also there is a promising future for CFD to become a useful tool in understanding airflow physiology and pathology.

Natural convection is intensively explored, especially in a valley-shaped trapezoidal enclosure, because of its broad presence in both technical settings and nature. This study deals with a trapezoidal cavity, which is initially filled with linearly stratified air. Though the side walls remain adiabatic, the bottom wall is heated, and the top wall is cooled. For the stratified fluid (air), the temperature of the fluid adjacent to the top and the bottom walls is the same as that of the walls. Natural convection in the trapezoidal cavity is simulated in two dimensions using numerical simulations, by varying Rayleigh numbers (Ra) from 100 to 108 with constant Prandtl number, Pr = 0.71, and aspect ratio, A = 0.5. According to numerical results, the development of transient flow within the enclosure owing to the predefined conditions for boundary may be categorized into three distinct stages: early, transitional, and steady or unsteady. The flow characteristics at each of the three phases and the impact of the Rayleigh number on the flow’s growth are stated in this study. In addition, heat transfer through the bottom and the top surfaces is described in this study.

Enterococci are commonly found in the environment and humans as a part of the normal micro-biota Among these, Enterococcus faecalis and Enterococcus faecium can convert into opportunistic pathogens, making them a major cause of nosocomial infections. The rapid diffusion of vanco-mycin-resistant strains and their impact on nosocomial settings is of considerable concern. Ap-proximately one-third of the E. faecium infections in Italy are caused by vancomycin-resistant strains. This study explored the hypothesis that the oral cavity could represent a silent reservoir of virulent enterococci. A sample of 862 oral flora specimens collected from healthy human volun-teers in Central Italy was investigated by real-time PCR to detect E. faecalis and E. faecium, as well as the genetic elements that most frequently determine vancomycin resistance. The prevalence of E. faecalis was 19%, a value that was not associated with alcohol consumption, tobacco smoking, or age of the subjects. Less frequently detected, with an overall prevalence of 0.7%, the E. faecium was more common among people older than 49 years of age. The genes conferring vancomycin resistance were detected in only one sample. Results indicate that the oral cavity can be considered a reservoir of clinically relevant enterococci; however, our data suggest that healthy individuals rarely carry vancomycin-resistant strains.

Background: Primary infection has been questioned as the pathogenetic cause of acute appendicitis. We attempted to identify the bacteria involved, and to investigate if their species, types, or combinations affected the severity of acute appendicitis in children. Methods: Samples from both the appendiceal lumen and the peritoneal cavity of 72 children who underwent appendectomy were collected to perform bacterial culture analysis. The outcomes were studied to see if and how they were associated with the severity of the disease. Regression analysis was performed to identify any risk factors associated with complicated appendicitis. Results: Escherichia coli, Pseudomonas aeruginosa and Streptococcus species were the most common pathogens found in the study population. The same microorganisms, either combined or separate, were the most common in the appendiceal lumen and the peritoneal cavity of patients with complicated appendicitis. Gram-negative bacteria, polymicrobial cultures in the peritoneal fluid and in the appendiceal lumen, were associated with complicated appendicitis. Polymicrobial cultures in the peritoneal cavity presented four times higher risk of complicated appendicitis. Conclusion: Polymicrobial presentation and gram-negative bacteria are associated with complicated appendicitis. Antibiotic regimens should target the combinations of the most frequently identified pathogens, speculating the value of early antipseudomonal intervention.

To reduce the carbon emissions during heating in the manufacturing process, microwaves have attracted significant attention. Microwave has a lot of advantages rather than traditional heating method such as rapid heating, lower thermal damage and eco-friendly process. In order to apply microwaves to manufacturing process, uniform and efficient heating is required. We have analyzed the effect of various design parameters such as cavity heights, the application of the reflector, and the number and positions of waveguides for uniform and efficient heating by numerical simulation and verified that by experiment. The results showed that a slight change in the cavity height altered the electromagnetic field distribution and heating parameters, such as the coefficient of variance and power absorption efficiency. With reflectors installed, uniform heating was achieved and power absorption was improved, with the spherical reflector showing the maximum efficiency. The use of double waveguides heated the target material in a uniform manner. An increase in the power supply also led to uniform heating. This large-scale analysis will be helpful in applying microwaves to actual industrial sites.

In this study, different configurations based on linear fiber lasers were proposed and experimentally demonstrated to measure the concentration of paracetamol liquid solutions in a range of 52.61 to 201.33 g/kg. The optical gain was provided by a commercial bidirectional Erbium-Doped Fiber Amplifier (EDFA) and the linear cavity was obtained using two commercial Fiber Bragg Gratings (FBGs). The main difference of each configuration was the coupling ratio of the optical coupler used to extract the system signal. The sensing head corresponded to a Single-Mode Fiber (SMF) tip that worked as an intensity sensor. The results reveal that, despite the optical coupler used (50:50, 60:40, 70:30 or 80:20), all the configurations reached the laser condition, however, the concentration sensing was only possible using a laser drive current near to the threshold value. The configurations using a 70:30 and an 80:20 optical coupler allowed to perform paracetamol concentration measurements with a higher sensitivity of (-3.00±0.24) pW/(g/kg). In terms of resolution, the highest value obtained was 1.75 g/kg, when it was extracted 20% of the output power to the linear cavity fiber laser configuration.

Background: The aim was to diagnose Candida in the oral cavity of subjects with type 2 diabetes mellitus (T2DM) using a genotyping technique and to compare the results with those from con-ventional diagnosis by Papanicolau (Pap) staining. Methods: Palatal mucosa smears were per-formed in 18 dental care patients diagnosed with T2DM and grade I, II, and III prosthetic stomatitis who met the inclusion criteria; 18 healthy control subjects were also included in the study. He-moglobin A1c (HbA1c) levels were determined from total blood. Using exfoliative cytology, the Pap staining technique was used to diagnose candidiasis. Exfoliative cytology was also used for molecular diagnosis; DNA was obtained for Candida genotyping and RNA was used for gene ex-pression studies. Results: Clinical patterns indicated that all subjects were positive for Candida; however, Pap analysis revealed only three positive subjects, whereas end-point polymerase chain reaction (PCR) analysis revealed fifteen subjects with some type of Candida. The most common Candida species found were Candida guilliermondii (38.8%), Candida krusei (33.3%), Candida tropicalis, and Candida lusitaniae (22.2%). Interestingly, the coexpression of different species of Candida was found in various patients. In all patients, HbA1c levels were increased. Gene expression analysis showed a significant decrease (p ≤ 0.05) in TLR2 expression in positive subjects, whereas TLR4 expression did not differ significantly among patients. Conclusions: The end-point PCR technique showed better sensitivity for diagnosis of Candida when compared with diagnosis by Pap staining. T2DM subjects showed an increased presence of C. guilliermondii that was correlated with decreased TLR2 expression

Background: Approximately 75% of all head and neck cancer patients are treated with radiotherapy (RT). RT to the oral cavity results in acute and late adverse events which can be severe and detrimental to a patient’s quality of life and function. The purpose of this study was to explore associations between RT dose to a defined oral cavity organ at risk (OAR) avoidance structure, provider and patient reported outcomes (PROs), opioid use, and hospitalization. Methods: This was a retrospective analysis of prospectively obtained outcomes using multivariable modeling. The study included 196 patients treated with RT involving the oral cavity for a head and neck tumor. A defined oral cavity OAR avoidance structure was used in all patients for RT treatment planning. Validated PROs were collected prospectively. Opioid use and hospitalization were abstracted electronically from medical records. Results: Multivariable modeling revealed the mean dose to the oral cavity OAR was significantly associated with opioid use (p=0.0082) and hospitalization (p=0.0356) during and within 30 days of completing RT. Conclusion: The findings of this study may be valuable in RT treatment planning for patients with tumors of the head and neck region to reduce the need for opioid use and hospitalization during treatment.

We report a diode pumped solid state (DPSS) laser used for intracavity pump-enhanced difference frequency generation (DFG) to create a 3.5 micron laser. Using a 50 mm-long periodically poled lithium niobate (PPLN) crystal inside the cavity of an Nd:YVO4 solid state laser at 1064 nm with 4.5 W pump power at 808 nm, and a 310 mW C-band signal at 1529 nm, up to 31 mW of mid-infrared output power at 3499 nm is obtained. The cavity requires no active stabilization and/or locking, and the entire cavity is &lt;8 cm in length. The obtained output power corresponds to a black box efficiency of 2.20 %W-1, which is the highest value reported to date for continuous wave DFG based on a bulk nonlinear optical crystal with no active stabilization. Potential future applications in free space optical communication are discussed as well.

Pump Sizing is the process of dimensional matching an impeller and stator to provide a satisfactory performance test result and good service life during the operation of progressive cavity pumps. In this process, historical data analysis and dimensional monitoring are done manually, consuming a large amount of man-hours and requiring a deep knowledge of progressive cavity pump behavior. This work presents the use of complex networks in the construction of a prototype to recommend interference during the Pump Sizing process in a Progressive Cavity Pump. For this, data from different expert applications were used in addition to individual control Excel spreadsheets to build the database used in the prototype. From the pre-processed data, complex network techniques and the Betweenness Centrality metric were used to calculate the degree of importance of each order confirmation, as well as to calculate the dimensionality of the rotors. The model was evaluated using the mean squared error (MSE), obtaining a MSE of 0.28 for the cases where there were recommendations for order confirmations. Based on the results obtained, it was realized that there is a similarity with the dimensional defined by design engineers during the Pump Sizing process.

Background: Metastatic tumors to the oro-facial tissues are rare, with an incidence ranging between 1% and 8% of all oral malignant tumors. Generally reported with a peak of incidence in the 5th–7th decades, but possibly occurring at any age, metastases may represent the first sign of an occult cancer or manifest in patient with an already known history of a primary carcinoma, mostly from the lungs, kidney, prostate, and colon-rectum in males, or uterus, breast, lung, and ovary in females. In the oro-facial tissues the sites mostly involved are the oral mucosa, gingiva/jawbones, tongue, and the salivary glands. Methods: A systemic Review of the literature on the oro-facial metastases from Renal Cell Carcinoma has been conducted by searching the most used databases, also focusing the attention on the Clear Cell histological variant, representing the most frequent one. Results: Among the 160 analyzed studies, 211 cases of oral metastases of renal cancer were found (148 in males, 70.1%; 63 in females, 29.8%), with an average age of 59.8 years. In almost 40% of cases, metastasis represented the first clinical manifestation of the primary tumor and 122 were histologically diagnosed as ccRCCs (57.8%). The tongue was involved in most of the cases (26% - 55 cases), followed by mandible (18.9% - 40 cases), gingiva (18.4% - 39 cases), maxilla (10.9% - 23 cases), parotid gland (10.4% - 22 cases), buccal mucosa (5.2% - 11 cases), lips (3.3% - 7 cases), hard palate (2.8% - 6 cases), soft palate, masticatory space and submandibular gland (0.9% - 2 cases), lymph nodes, tonsil and oral floor (0.4% - 1 case). Among the 122 ccRCCs (84 were males, 68.8 %; 38 females, 31.1%), with an average age of 60.8 years and representing in 33.6% the first clinical manifestation, the tongue remained the most involved site (25.4% - 31 cases), followed by the gingiva (17.2% - 21 cases), parotid gland (13,1% - 16 cases), mandibular bone (12.2% - 15 cases), maxillary bone (11.4% - 14 cases), buccal mucosa and lips (4.9% - 6 cases), hard palate (4% - 5 cases), submandibular gland and soft palate (1.6% - 2 cases), lymph nodes, tonsil, oral floor and masticatory space (0.8%. 1 case). The clinical presentation in soft tissues was represented by a fast-growing exophytic mass, sometimes accompanied by pain. Instead inn bone appeared as radiolucent lesions, with ill-defined borders and cortical erosion. Conclusions: Our data focus the attention on the incidence of Renal cancer Metastases in the oro-facial tissues. Their early identification surely represents a diagnostic challenge, especially when the clinical work-up is limited to the cervico-facial region. Nevertheless, early diagnosis and recently introduced adjuvant therapies may represent the key for better outcomes. Therefore, general guidelines about clinical and radiological identification of oro-facial potentially malignant lesions should be part of the cultural background of any dentists.

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

The absolute absorption cross section of the ethyl peroxy radical, C2H5O2, in the Ã←X ̃ electronic transition with the peak wavelength at 7596 cm-1, has been determined by the method of dual wavelengths time resolved continuous wave cavity ring down spectroscopy. C2H5O2 radicals were generated from pulsed 351 nm photolysis of C2H6/Cl2 mixture in presence of O2 and detected on one of the CRDS paths. Two methods have been applied for the determination of the C2H5O2 absorption cross section: (i) based on Cl-atoms being converted alternatively to either C2H5O2 by adding C2H6 or to hydro peroxy radicals, HO2, by adding CH3OH to the mixture, whereby HO2 was reliably quantified on the second CRDS path in the 21 vibrational overtone at 6638.2 cm-1 (ii) based on the reaction of C2H5O2 with HO2, measured under either excess HO2 or under excess C2H5O2 concentration. Both methods lead to the same peak absorption cross section of C2H5O2,7596 cm-1 = (1.0±0.2) × 10-20 cm2. The rate constant for the cross reaction between of C2H5O2 and HO2 has been measured to be (6.5±1.6) × 10-12 cm3 molecule-1 s-1.

PHA synthases (PhaC) are grouped into four classes based on the kinetics and mechanisms of reaction. The grouping of PhaC enzymes into four classes is dependent on substrate specificity, according to the preference in forming short chain length (scl) or medium chain length (mcl) polymers: class I, class III, and class IV produce scl-PHAs depending on propionate, butyrate, valerate and hexanoate precursors, while class II phaC synthesize mcl-PHAs based on the alkane (C6 to C14) precursors. PHA synthases of class I, in particular PhaC_Cs from Chromobacterium USM2 and PhaC_Cn/RePhaC1 from Cupriavidus necator/R. eutropha, have been analysed and the crystal structures of the C-domains have been determined. PhaC_Cn/RePhaC1 was also studied by small angle X-ray scattering (SAXS) analysis. Models have been proposed for dimerization, catalysis mechanism, substrate recognition and affinity, product formation and product egress route. The assays based on amino acid substitution by mutagenesis have been useful to validate the hypothesis on the role of amino acids in catalysis and in accommodation of bulky substrates, for the synthesis of PHB co-polymers and medium chain length-PHA polymers with optimized chemical properties.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

Fabry-Pérto (FP) cavity is the essential component of ultra-stable laser (USL) for gravitational wave detection, which couples multi-physic (Optical/Thermal/Mechanics) fields and requires ultra-high precision. To satisfy the requirements of precise and efficient design, a multi-physic coupling optimization method for fixing cubic FP cavity based on data learning is proposed. A multi-physic model for the cubic FP cavity is established and the performance is obtained by finite element analysis. The key performance indices (V, wF, wF) and key design variables (d, l, F) are determined considering the features of the FP cavity. The 49 sets of data by orthogonal experiment are acquired for the establishment and comparison of different data learning models (NN, RSF, KRG). The result turns out that the neural network has the best performance. Based on NSGA-II, the Pareto optimal front is obtained and the optimal combination of design variables is finally determined as {5,32,250}. The performance after optimization has proven to be a great improvement, of which the displacement under the fixing force and vibration test are decreased by more than 60%. The optimization strategy can not only help the design of the FP cavity but also enlighten other optimization fields.

Smoking has been established as a major risk factor for developing oral squamous cell carcinoma (OSCC), but less attention has been paid to the effects of smokeless tobacco products. Our objective is to identify potential biomarkers to distinguish the biological effects of combustible tobacco products from those of non-combustible using oral cell lines. Normal human gingival epithelial cells (HGEC), non-metastatic (101A) and metastatic (101B) OSCC cell lines were exposed to different tobacco product preparations (TPPs) including cigarette smoke total particulate matter (TPM), whole-smoke conditioned media (WS-CM), smokeless tobacco extract in complete artificial saliva (STE), or nicotine (NIC) alone. We performed microarray-based gene expression profiling and found 3456 probe sets from 101A, 1432 probe sets from 101B, and 2717 probe sets from HGEC to be differentially expressed. Gene Set Enrichment Analysis (GSEA) revealed xenobiotic metabolism and steroid biosynthesis were the top two pathways that were upregulated by combustible but not by non-combustible TPPs. Notably, aldo-keto reductase genes, AKR1C1 and AKR1C2, were the core genes in the top enriched pathways and were statistically upregulated more than 8 fold by combustible TPPs. Our qRT-PCR results statistically support AKR1C1 as a potential biomarker for differentiating the biological effects of combustible from non-combustible tobacco products.

Interaction of an electromagnetic field with matter in a laser cavity without the assumption of a fixed direction of the transverse electric field, described by the two-level Maxwell-Bloch equations, is studied. By using a perturbative nonlinear analysis, performed near the laser threshold, we report on the derivation of the laser (3+1)D vectorial complex cubic-quintic complex Ginzburg-Landau equation. Furthermore, we study the modulational instability of the plane waves both theoretically using the linear stability analysis, and numerically, using direct simulations via the split-step Fourier method. The linear theory predicts instability for any amplitude of the primary waves. Our numerical simulations confirm the theoretical predictions of the linear theory as well as the threshold of the amplitude of perturbations. The system understudy shows a deep dependence on the laser cavity parameters, for which there appear wave patterns in accordance with the predictions from the gain spectrum.

2-Hydroxypropyl-β-cyclodextrin (HPβCD) has unique properties to enhance the stability and the solubility of low water-soluble compounds by inclusion complexation. Understanding of the structural properties of HPβCD and its derivatives based on the number of 2-hydroxypropyl (HP) substituents at the a-D-glucopyranose subunits is rather important. In this work, replica exchange molecular dynamics simulations were performed to investigate the conformational changes of single- and double-sided HP-substitution called as 6-HPβCDs and 2,6-HPβCDs, respectively. The results show that glucose subunits in both 6-HPβCDs and 2,6-HPβCDs have lower chance to flip than in βCD. Also, HP groups are occasionally blocking the hydrophobic cavity of HPβCDs, thus hindering the drug inclusion. We found that HPβCDs with high number of HP-substitutions are more likely to be blocked, while HPβCDs with double-sided HP-substitution are even more probable to be blocked. Overall, 6-HPβCDs with three and four HP-substitutions are highlighted as the most suitable structures for guest encapsulation based on our conformational analyses such as structural distortion, radius of gyration, circularity and cavity self-closure of the HPβCDs.

In this study, the shape and size of a combustion cavity with a fracture zone in the gasified coal seam was determined with use control boreholes and a ground-penetrating radar (BGPR) test. The underground coal gasification (UCG) field-scale experiment was performed in Carboniferous strata in coal seam 501 at a depth of approx. 460 m in the Wieczorek hard-coal mine in the Upper Silesian Coal Basin, Poland. After the termination of the UCG reactor, five coring boreholes were drilled to identify the geometry of the resulting combustion cavity and the impact of the UCG process on the surrounding rock mass. Borehole ground-penetrating radar measurements were performed using a 100 MHz antenna in three boreholes with a length of about 40-50 m. This enabled the identification of the boundaries of the combustion cavity and the fracture zone in the coal seam. The fracture zones of rock layers and lithological borders near the control borehole were also depicted. As a result, the cavity was estimated to have a length of around 32 m, a width of around 7 m and a height of around 5 m. The analyses performed with the control boreholes and the BGPR provided sufficient information to determine the geometry of the combustion cavity and the fracture zone.

This work communicates cavity ring-down spectroscopy (CRDS) of methylidyne (CH) in a chemiluminescent plasma that is produced in a microwave cavity. Of interest are the rotational lines of the 0-0 vibrational transition for the A-X band and the 1-0 vibrational transition for the B-X band. The reported investigations originate from CH-radical research in 1996 that constituted the first case of applying CRDS to the CH radical. The report also includes recent analysis that shows excellent agreement of measured and computed data, and it communicates CH line strength data.

Epidemiological data indicate that 5.8% of cancer deaths world-wide are attributable to alcohol consumption. The risk of cancer is higher in tissues in closest contact on ingestion of alcohol, such as the oral cavity, pharynx and esophagus. The risk of these cancers is increased even in people who have only one alcoholic drink per day. However, since ethanol is not mutagenic and the carcinogenic metabolite of ethanol (acetaldehyde) is mostly produced in the liver, it is not clear why alcohol use preferentially exerts a local carcinogenic effect. It is well known that ethanol causes cell death at the concentrations present in alcoholic beverages; however, this effect has been overlooked probably because dead cells cannot give rise to cancer. Here I discuss that the cytotoxic effect of ethanol on the cells lining the oral cavity, pharynx and esophagus activates the division of the stem cells located in deeper layers of the mucosa to replace the dead cells. Every time stem cells divide, they become exposed to unavoidable errors associated with cell division (e.g., mutations arising during DNA replication and chromosomal alterations occurring during mitosis) and also become highly vulnerable to the genotoxic activity of endogenous and exogenous DNA-damaging agents (e.g., reactive oxygen species, acetaldehyde and tobacco carcinogens). Alcohol consumption probably increases the risk of developing cancer of the oral cavity, pharynx and esophagus by promoting the accumulation of cell divisions in the stem cells that maintain these tissues in homeostasis. Because the cytotoxic activity of ethanol is concentration-dependent, the risk of these cancers will not only increase with increasing amounts of ethanol, but also with increasing concentrations; an ounce of whisky is probably more carcinogenic when taken undiluted than when taken mixed with non-alcoholic beverages. The local cytotoxic effect of ethanol can also explain the known synergistic effect of alcohol and tobacco use on the risk of these cancers. Understanding the mechanisms of carcinogenicity of alcohol is important to reinforce the epidemiological evidence and to raise public awareness of the strong link between alcohol consumption and cancer.

We propose a theoretical method for the deterministic shaping of quantum light via photon number state selective interactions. Nonclassical states of light are an essential resource for high precision optical techniques that rely on photon correlations and noise reshaping. Notable techniques include quantum enhanced interferometry, ghost imaging, and generating fault tolerant codes for continuous variable optical quantum computing. We show that a class of nonlinear-optical resonators can transform many-photon wavefunctions to produce structured states of light with nonclassical noise statistics. The devices, based on parametric down conversion, utilize the Kerr effect to tune photon number dependent frequency matching, inducing photon number selective interactions. With a high amplitude coherent pump, the number selective interaction shapes the noise of a two-mode squeezed cavity state with minimal dephasing, illustrated with simulations. We specify the requisite material properties to build the device and highlight the remaining material degrees of freedom which offer flexible material design.

It is known that complexes based on natural polysaccharides are able to eliminate bone defects. Prolonged hyperglycemia means low bone regeneration and a chronic inflammatory response. The purpose of the study was to increase the efficiency of early bone formation in a cavity of critical size in diabetes mellitus in the experiment. The polyelectrolyte complex contains high molecular ascorbate of chitosan, chondroitin sulfate, sodium hyaluronate, heparin, adgelon serum growth factor, sodium alginate and amorphous nanohydroxyapatite (CH-SA-HA). Studies were conducted on 5 groups of white female Wistar rats: group 1 - regeneration of a bone defect in healthy animals under a blood clot; group 2 - regeneration of a bone defect under a blood clot in animals with diabetes mellitus; group 3 - bone regeneration in animals with diabetes mellitus after filling the bone cavity with a collagen sponge; group 4 - filling of a bone defect with a CH-SA-HA construct in healthy animals; Group 5 - filling of a bone defect CH-SA-HA in animals with diabetes mellitus. Implantation of the CH-SA-HA construct into bone cavities in type I diabetic rats can accelerate the rate of bone tissue repair. The inclusion of modifying polysaccharides and apatite agents in the construction may be a prospect for further improvement of the properties of implants.

Silicon-based photonic integrated circuit (PIC) is a research focus in producing high-density photonics. One of the potential applications of silicon PIC is the sensing and measurement system. In this work, we use the one-dimensional photonic crystal (1D-PhC) cavity design which and utilize it at the PIC level design. The 1D PhC design used as the compact model has the same characteristics as experimentally demonstrated in previous works. The compact model is made from the S-parameter extraction of the 1D-PhC device which is done by using Lumerical FDTD software. The PIC design integrates the 1D-PhC device as a sensing component with a PN-phase shifter (PN-PS) to function as a refractive index (RI) sensor calibration or tuning circuit. A custom design of PN-PS device is used by simulating and extracting the bias voltage-effective index (bias-Neff) data by using Lumerical DEVICE and MODE into the circuit simulator. The circuit-level simulation is done by using Lumerical Interconnect software. Finally, we show the GDSII layout design of the 1D-PhC based photonic sensor calibration circuit with an analysis of generic silicon PIC design rules. The designed PIC is applicable for the bio-sensing applications and photonic SOC component. This work also shows the promise of PIC design approach for further PIC development.