In tissue engineering scaffolds take the place of the natural extra cellular matrix (ECM). The natural ECM is the extracellular part of animal tissue that usually provides structural support to the animal cells in addition to performing various other important functions. The design aspect along with the choice of the material for the artificial scaffold is very crucial to cell differentiation, adhesion, proliferation, and the transport of the growth factors or other bio molecular signals. In addition to the material and design of the scaffolds, it is necessary to replicate the normal physiological situation if the scaffold has to function as an implant. The cells have to be located in the porous scaffold to form a three dimensional assembly. The article discusses the important factors to be considered while designing a scaffold for tissue engineering and regenerative medicine.

The healing of osteochondral defects (OCD) resulting from injury, osteochondritis, or osteoarthritis in middle- and old-age individuals, bearing lesions in the cartilage and bone, pain, and loss of joint function, presents challenges to the clinical practitioners because of non-regenerative cartilage and the limitations of current therapies. Bioactive peptide-based osteochondral (OC) tissue regeneration is becoming more popular because it does not have the immunogenicity, misfolding, or denaturation problems associated with original proteins. Periodically, reviews are published on the regeneration of bone and cartilage; however, none of them address the simultaneous healing of these tissues in the complicated heterogeneous environment of the OC interface. As regulators of cell adhesion, proliferation, differentiation, angiogenesis, immunomodulation, and antibacterial activity, potential therapeutic strategies for OC defects utilizing bone and cartilage-specific peptides should be examined and investigated. Therefore, the main goal of this review is to study how they contribute to the healing of OC defects, either alone or in conjunction with other peptides and biomaterials.

In order to overcome the disadvantages of existing treatments in heart valve tissue engineering, decellularization studies are carried out. The main purpose of decellularization is to eliminate the immunogenicity of biologically derived grafts and to obtain a scaffold that allows recellularization while preserving the natural tissue architecture. SD and SDS are detergent derivatives frequently used in decellularization studies. The aim of our study is to decellularize the pulmonary heart valves of young Merino sheep by using low-density SDS and SD detergents together, and then to perform their detailed characterization to determine whether they are suitable for clinical studies. Pulmonary heart valves of 4-6 month old sheep were decellularized in detergent solution for 24 hours. The amount of residual DNA was measured to determine the efficiency of decellularization. Then, the effect of decellularization on the ECM by histological staining was examined. In addition, the samples were visualized by SEM to determine the surface morphologies of the scaffolds. Uniaxial tensile test was performed to examine the effect of decellularization on biomechanical properties. The results showed DNA removal of 94% and 98% from the decellularized leaflet and artery portions after decellularization relative to the control group. No cell nuclei were found in histological staining and it was observed that the 3-layer leaflet structure was preserved. As a result of the tensile test, it was determined that there was no statistically significant difference between the control and decellularized groups in the UTS and elasticity modulus, and the biomechanical properties did not change. In conclusion, we suggest that the pulmonary valves of decellularized young Merino sheep can be used as a initial matrix in heart valve tissue engineering studies.

Green electrospun materials are gaining popularity in the quest for a more sustainable environment for human life. Bee pollen (BP) is a valuable apitherapeutic product, and has many beneficial features such as, antioxidant and antibacterial properties. Alginate is a natural and low-cost polymer. Both natural materials show good compatibility with human tissues for biomedical applications and have no toxic effect on the environment. In this study, bee pollen-loaded sodium alginate and polyvinyl alcohol (SA/PVA) nanofibrous mats were fabricated by the electrospinning technique. The green electrospun nanofibrous mats were analyzed by scanning electron microscopy (SEM), Fourier transforms infrared spectroscopy (FTIR), and differential scanning calorimeter (DSC). According to the findings of the study, the toxin-free electrospinning method is suitable for producing green nanomaterial. Because of the useful properties of the bee pollen and the favorable biocompatibility of the alginate fibers, the bee pollen-loaded SA/PVA electrospun mats have the potential for use in a variety of biomedical applications

Many wounds are unresponsive to current available treatment techniques and therefore there is an immense need to explore suitable materials including biomaterials, which are being considered as the crucial factor to accelerate the healing cascade. In this study, we fabricated polyhydroxyalkanoate based antibacterial mats via electrospun technique. One-pot green synthesized graphene decorated silver nanoparticles (GAg) were incorporated into the fibres of poly-3 hydroxybutarate-co-12 mol% hydroxyhexanoate (P3HB-co-12mol% HHx), a co-polymer of polyhydroxyalkanoate (PHA) family which is highly biocompatible, biodegradable and flexible in nature. The synthesised PHA/GAg biomaterial was characterized by field emission scanning electron microscopy (FESEM), elemental mapping, thermogravimetric analysis (TGA), UV-visible spectroscopy (UV-vis) and Fourier transform infrared spectroscopy (FTIR). In-vitro antibacterial analysis were performed to investigate the efficacy of PHA/GAg against gram positive Staphylococcus aureus (S.aureus) strain 12600 ATCC and gram negative Escherichia coli (E.coli) strain 8739 ATCC. The results indicated that the PHA/GAg demonstrated significant reduction of Staphylococcus aureus (S.aureus strain 12600 ATCC) and Escherichia coli (E.coli strain 8739 ATCC) as compared to bare PHA or PHA-rGO in 2 hours of time. The P value (P< 0.05) was obtained by using 2 sample T-test distribution.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

Salmon aquaculture generates a substantial volume of waste material, offering potential for biomaterial production. This industry produces significant waste, which can be repurposed for various biological applications, particularly in biomaterial production for tissue engineering with pertinent applications in osteo-conduction, osteo-induction, and clinical/surgical bone regeneration and repair. The process involves a standardized pre-treatment stage aimed at minimizing biological waste content. Subsequently, the treatment stage, contingent on the chosen methodology, facilitates the removal of proteins, lipids, and other compounds, leaving the mineral phase as a valuable substrate. The selection of the optimal method, whether alkaline hydrolysis, calcination, or NaOH hydrolysis, for obtaining this substrate necessitates thorough examination through chemical, physical, and biological assessments, including Raman Spectroscopy and X-Ray Diffraction. This study aims to identify the most efficient approach for hydroxyapatite production derived from salmon waste.

Silk is a globally renowned abundant biopolymer obtained from various sources of the Lepidoptera family, among which the most commonly used and researched are spider silk and silk worm silk. All varieties of silk have beneficial characteristics such as high tensile strength, biocompatibility, producing a reduced immune response in a biological system, biodegradability, and the ability to withstand environmental stresses as well. These features make silk suitable for a number of applications as a biomaterial. The vast potential of silk and its proteins in cosmetics, oncology, tissue engineering, TOC screenings, for preserving food, cosmetic product as a silk gel and bioremediation makes it a well-sought biopolymer among researchers. Experiments over the years have revealed that biomaterials constituting silk are very potent but are yet to be scaled up for commercial uses, but the various advantageous properties of silk biomaterial far overshadows the impeding problems of production.

In horses, there is an increasing interest in developing long-lasting drug formulations, with bi-opolymers as viable carrier alternatives in addition to their use as scaffolds, suture threads, screws, pins, and plates for orthopedic surgeries. This communication focuses on the prolonged biocompatibility and biodegradation of PLA, prepared by hot pressing at 180 ºC. Six samples were implanted subcutaneously on the lateral surface of the neck of one horse. The polymers remained implanted for 24 to 57 weeks. Physical examination, plasma fibrinogen, and the mechanical noci-ceptive threshold (MNT) were performed. After 24, 28, 34, 38, and 57 weeks, the materials were removed for histochemical analysis using hematoxylin-eosin and scanning electron microscopy (SEM). There were no essential clinical changes. MNT decreased after the implantation procedure, returning to normal after 48h. A foreign body response was observed by histopathologic evalua-tion up to 38 weeks. At 57 weeks, no polymer or fibrotic capsules were identified. SEM showed surface roughness suggesting a biodegradation process, with an increase in the average pore di-ameter. As in the histopathological evaluation, it was not possible to detect the polymer 57 weeks after implantation. PLA showed biocompatible degradation and these findings may contribute to future research in the biomedical area.

Three-dimensional matrices are a new strategy used to tackle type I diabetes; a chronic metabolic disease characterized by the destruction of beta pancreatic cells. Type I collagen is an abundant extracellular matrix (ECM), component that has been used to support cell growth. However, pure collagen possesses some difficulties including low stiffness and strength, and high susceptibility to cell-mediated contraction. Therefore, we developed a collagen hydrogel with a poly(ethylene glycol) diacrylate (PEGDA) interpenetrating network (IPN), functionalized with vascular endothelial growth factor (VEGF) to mimic the pancreatic environment for the sustenance of beta-pancreatic cells. We analyzed the physicochemical characteristic of the hydrogels and found that they were successfully synthesized. The mechanical behavior of the hydrogels improved with the addition of VEGF, and the swelling degree and the degradation were stable over time. In addition, it was found that 5 ng/mL VEGF-functionalized collagen/PEGDA IPN hydrogels sustained and enhanced viability, proliferation, respiratory capacity and functionality of beta pancreatic cells. Hence, this is a potential candidate for future preclinical evaluation, which may be favorable for diabetes treatment.

Titanium (Ti-6Al-4V) substrates were functionalized through the covalent binding of fibronectin, and the effect of the presence of this extracellular matrix protein on the surface of the material was assessed employing mesenchymal stem cell (MSC) cultures. The functionalization process com-prised the usage of the activation vapor silanization (AVS) technique to deposit a thin film with a high surface density of amine groups on the material, followed by the covalent binding of fi-bronectin to the amine groups using the N-(3-dimethylaminopropyl)-N′-ethylcarbodiimide hy-drochloride / N-hydroxysuccinimide (EDC/NHS) crosslinking chemistry. The biological effect of the fibronectin on murine MSCs was assessed in vitro. It was found that functionalized samples not only showed enhanced initial cell adhesion compared with bare titanium, but also a three-fold increase in the cell area, reaching values comparable to those found on the polystyrene controls. These results represent a clear indication of the potential of modulating the response of the or-ganism to an implant through the covalent binding of extracellular matrix proteins on the pros-thesis.

Rapeseed meal (RM) is an important agroindustrial by-product produced in large quantities by oil extraction from seeds. However, the efficient utilization of RM as animal feed is limited by its low metabolizable energy, poor palatability, and high levels of fiber and anti-nutritional components. Here, we investigate the potential of enriching RM with single-cell protein by fermentation with conventional and unconventional yeasts, to make a nutritionally improved feed component. The process of simultaneous saccharification and fermentation improved the parameters of the waste biomass, especially the protein content, the amount of crude fiber, and the degree of biotransformation of isoflavone compounds present in the waste material. Fermentation yielded the highest protein gain for the Saccharomyces cerevisiae Ethanol Red strain (ΔN=2.38%) at a biomass load of 12.5 g and for Scheffersomyces stipitis (ΔN=2.34%) at an enzyme dose of 0.125ml/10g DM. Crude fiber content (CF) was reduced by 2.55–7.18%. The SSF process resulted in the conversion of isoflavones to forms with fewer adverse effects and lower estrogenic activity.

Background: Xenogenous bone has been proposed as an alternative to overcome the disadvantages of autogenous grafting. The aim of the present study was to study bone dynamics at inlay and onlay xenografts used for bone augmentation applying a ring technique. Methods: The bone at the lateral surface of the mandibular angle of 12 adult male New Zealand White rabbits was exposed bilaterally. The cortical layer received multiple perforations at one side of the mandible and a xenograft block of collagenated cancellous equine bone, 7 mm in diameter and 3 mm in width, was fixed on the prepared surface using an implant (onlay group). On the opposite side, a defect 7 mm in diameter and 3 mm in depth was prepared, the xenograft block was adapted to the defect and fixed with an implant (inlay group). Results: After ten weeks of healing, in the onlay grafts, new bone was mainly formed on the trabeculae surface, reaching in some specimens the most coronal regions of the block. In the inlay grafts, new bone was found arranged on the trabecular surfaces but also occupying the spaces among the trabeculae. The entrance of the defect was often found close at the top of the block by newly formed bone. A higher percentage of new bone was found in the inlay (19.0 ±9.3%) compared to the onlay (10.4 ±7.4%) groups (p=0.031). The mean gain in osseointegration at the implant in relation to the base of the original 3 mm deep defect was 0.95 ±1.05% at the onlay group and 0.78 ±0.71% at the inlay group (p=0.603). Conclusion: The inlay grafts exhibited a higher new bone percentage than the onlay grafts possibly due to the defect conformation that presented more sources for bone formation. The trabecular conformation and the composition of the grafts made possible the expression of the osteoconductive properties of the material used. This resulted, in several specimens, in growth of bone on the graft trabeculae toward the most superior regions in both groups, and in the closure of the coronal entrance of the defects in the inlay group.

Background: The conformation of the recipient site for an inlay graft presents an increased contact with the parent bone compared to the onlay graft. This might favor bone growth within the inlay compared to the onlay grafts. Hence, the objective of this study was to compare bone incorporation and remodeling process of xenogeneic en bloc grafts, placed using two bone grafting techniques, i.e., onlay vs. inlay. Methods: In this prospective, randomized, split-mouth study (test and control sides in the same animal), two bone grafting techniques were comparatively evaluated on the lateral aspect of the rabbit mandibles. One side was prepared with perforations (onlay site), whereas the other side was prepared with trephines and drills to obtain a wide (7 mm) standardized recipient site (inlay site). A xenogeneic bone block was fixed in the center with a titanium screw in both sides of the mandible and covered with a collagen membrane. Two healing periods were applied in the study: 2 and 10 weeks of healing. Results: after 2 weeks of healing, the mean percentage of new bone was 10.4% and 23.3% at the onlay and inlay grafts, respectively (p=0.022). After 10 weeks of healing, new bone increased to 13.2% and 25.4%, respectively (p=0.080). In this period of healing, the inlay grafts presented new bone percentage &gt;20% in all regions examined while the onlay graft presented a lower percentage in the most external regions of the graft. Conclusion: The percentage of new bone increased faster and was higher in the inlay compared to the onlay grafts. The composition of the grafts allowed new bone to reach the most peripheral regions in both graft groups, even though it was higher in the inlay group. A marginal closure of the defects by newly formed bone was observed in the inlay group.

The capability of radially polymerized bio-dendrimers and hyperbranched polymers for medical applications is well established. Among them, perhaps the most important are those that involve interactions with the regenerative mechanisms of cells. Dendritic polymers due to their distinctive architecture may play a multitude of roles such as protein biomimicry (collagen, elastin, hydroxy apatite production), gene and drug delivery (cell differentiation, antimicrobial protection), surface chemistry and charge modulation (adhesion to cells and tissues), polymer cross-linking (eye, skin and internal organ wound healing). The review highlights all the different categories of hard and soft tissues that may be remediated with their contribution. The reader will be also exposed to the incorporation methods to established biomaterials such as scaffolds, the functionalization strategies, and the synthetic paths for the assembly from biocompatible building blocks and natural metabolites.

The influence of the hot isostatic pressing (HIP) post-processing step on structural and phase changes, porosity healing and mechanical strength in a powder metallurgy Ti35Nb2Sn alloy was studied. Powders were pressed at room temperature at 750 MPa, and then sintered at 1,350°C in a vacuum for 3 h. The standard HIP process at 1,200°C and 150 MPa for 3 h was performed to study its effect on a Ti35Nb2Sn powder metallurgy alloy. The influence of the HIP process and cold rate on density, microstructure, the quantity of interstitial elements, mechanical strength and Young's modulus was investigated. HIP post-processing for 2 h at 1,200°C and 150 MPa led to greater porosity reduction and a marked retention of the β phase at room temperature. The slow cooling rate during the HIP process affected phase stability, with a large amount of α”-phase precipitate, which decreased the titanium alloy’s yield strength.

Composite materials are widely used in the dental field in clinics as biomaterials. For example, it has been used as a biomaterial to repair caries and restore masticatory function, and as a cement to adhere the restoration to the tooth substrate. In order to demonstrate its function, dental biomaterials are measured their mechanical strength. From such basic research, we explained the potential of dental biomaterials, especially flexural strength and modulus of elasticity. Mechanical properties of dental biomaterials similar to those of the tooth, thermal stimulation, and aesthetic elements in the oral cavity. In this part, we will introduce the commercialized products of composites suitable for the characteristics and tooth quality, and provide the reader with the characteristics from the flexural characteristics of the composite materials used in clinical dentistry. In clinical performance, it might be advisable to delay polishing when composite biomaterials are used for luting materials, filling materials and core build-up materials since improved the flexural strength and the flexural modulus of elasticity were displayed after 1-day storage. And it is thought that flexural strength or characteristics is a significant important mechanical property of oral biomaterials.

Recently, nanotechnologies have become increasingly prominent in the field of bone tissue engineering (BTE), offering substantial potential to advance the field forward. These advancements manifest in two primary ways: the localized application of nanoengineered materials to enhance bone regeneration and their use as nano-vehicles for delivering bioactive compounds. Despite significant progress in the development of bone substitutes over the past few decades, it is worth noting that the quest to identify the optimal biomaterial for bone regeneration remains a subject of intense debate. Ever since its initial discovery, poly(lactic-co-glycolic acid) (PLGA) has found widespread use in BTE due to its favorable biocompatibility and customizable biodegradability. This review provides an overview of contemporary advancements in the development of bone regeneration materials using PLGA polymer. The review covers some of PLGA properties with a special focus on modifications of these properties towards bone regeneration. Furthermore, we delve into the techniques for synthesizing PLGA nanoparticles (NPs), the diverse forms in which these NPs can be fabricated, and the bioactive molecules that exhibit therapeutic potential for promoting bone regeneration. Additionally, we addressed some of the current concerns regarding the safety of PLGA NPs, and PLGA-based products available in the market. Finally, we briefly discussed some of the current challenges and proposed some strategies to functionally enhance the fabrication of PLGA NPs towards BTE. We envisage that the utilization of PLGA NP holds significant potential as a potent tool in advancing therapies for intractable bone diseases.

Renewable resources gain increasing interest as source for environmentally benign biomaterials, such as drug encapsulation/release compounds, and scaffolds for tissue engineering in regenerative medicine. Being the second largest naturally abundant polymer, the interest in lignin valorization for biomedical utilization is rapidly growing. Depending on resource and isolation procedure, lignin shows specific antioxidant and antimicrobial activity. Today, efforts in research and industry are directed toward lignin utilization as renewable macromolecular building block for the preparation of polymeric drug encapsulation and scaffold materials. Within the last five years, remarkable progress has been made in isolation, functionalization and modification of lignin and lignin-derived compounds. However, literature so far mainly focuses lignin-derived fuels, lubricants and resins. The purpose of this review is to summarize the current state of the art and to highlight the most important results in the field of lignin-based materials for potential use in biomedicine (reported in 2014–2018). Special focus is drawn on lignin-derived nanomaterials for drug encapsulation and release as well as lignin hybrid materials used as scaffolds for guided bone regeneration in stem cell-based therapies.

TiNbZrTa alloys are promising for multidisciplinary applications, such as refractory and biomedical purposes due to their high thermal stability and non-toxicity. Hardness and elastic modulus are among the key features for their adequate industrial applications. The influence of porosity and Ti/Ta ratio were investigated on TiNbZrTa alloys produced by three different processing routes, i.e., (i) blend element and posterior press and sintering (BE + P&amp;S), (ii) mechanical alloying with press and sintering (MA + P&amp;S), and (iii) arc melting and casting. Atomic diffusion was improved during processing, resulting in lower porosity in the following order: casting &lt; MA + P&amp;S &lt; BE + P&amp;S. Ta offered limited atomic diffusion due to its high melting point compared to other constituent elements. Thus, the total porosity of alloys increased with increasing the Ta contents, i.e., by lowering the Ti/Ta ratio. However, the Ti/Ta ratio did not considerably affect the bonding energy or the elastic modulus. Hardness was increased significantly in dense alloys compared to the porous ones. However, porosity and Ti/Ta ratio did not show a clear trend in hardness among the porous alloys.