Trends focused on the Global Innovation Index (GII) as a measure for progress of nanochemistry. This paper provides projections of recent developments in the word in nanochemistry based on the Global Innovation Index as a predictor for certain Arab countries. The GII is an annual ranking of countries by its ability and performance in innovation and is calculated on a basic average from five and two pillars in two sub-indexes, the Innovation Input Index and the Innovation Output Index. Each pillar represents a trait of creativity and consists of up to five measures, with a weighted average formula for measuring their ranking. In 2008, the GII rose to 36.3 in 2016 from 0.5. The GII is smaller than the GII in Arabic countries worldwide. During the years 2013-2016, the worldwide GII was increasing while for the same period, for Arabic countries, this decline could be explained by economic and industrial wars in the Arab region.

NACA 0015 and NACA 4415 aerofoil are most common four digits and broadly used aerodynamic shape. Both of the shapes are extensively used for various kind of applications including turbine blade, aircraft wing and so on. NACA 0015 is symmetrical and NACA 4415 is unsymmetrical in shape. Consequently, they have big one-of-a-kind in aerodynamic traits at the side of widespread differences of their utility and performance. Both of them undergo the same fluid principle while applied in any fluid medium giving dissimilar outcomes in aerodynamics behavior. On this work, experimental and numerical investigation of each NACA 0015 and NACA 4415 is done to decide their performance. For this purpose, aerofoil section is tested for a prevalence range attack of angle (AOA). The study addresses the performance of NACA 0015 and NACA 4415 and evaluates the dynamics of flow separation, lift, drag, pressure and velocity contour and so on. This additionally enables to layout new optimistic aerofoil, which is critical to enhance the efficiency and performance of an aircraft in terms of lift enhancement and drag reduction.

In this paper we develop a forecasting algorithm for recurrent patterns in consumer demand. We study this problem in two different settings: pull and push models. We discuss several features of the algorithm concerning sampling, periodic approximation, denoising and forecasting.

Multiple sensor nodes known as detection stations make the sensor networks; each node is light and portable. Every sensor node contains power source, microcomputer, transducer and transceiver. Power source provides power to each node. Micro-computer is used for storing and processing the output coming from the sensors. The transducer is used to generate the signals and the transceiver is used to receive and transmit data to the central computer. Eavesdropping gets facilitated with wireless communication, and it has many useful applications in military, homeland, hostile and uncontrolled environments. So it is prone to the high level of security. The process in which information is gathered to form a summarized type for analysis is known as data aggregation, as it is used to reduce the energy consumption in wireless sensor networks. The security issues have become crucial in data aggregation, especially when gets deployed in hostile and remote environment. In wireless sensor networks many secure aggregations have been proposed. It still faces some resource constrained that’s why new techniques are needed. In our survey we will discuss those approaches and their pros and cons.

This paper draws an earlier book (with Evans and Higgins) entitled Bad Call: Technology’s Attack on Referees and Umpires and How to Fix It (hereafter Bad Call) and its various precursor papers. These show why it is that current match officiating aids are unable to provide the kind of accuracy that is often claimed for them and that sports aficianados have been led to expect from them. Accuracy is improving all the time but the notion of perfect accuracy is a myth because, for example, lines drawn on sports fields and the edges of balls are not perfectly defined. The devices meant to report the exact position of a ball – for instance ‘in’ or ‘out’ at tennis – work with the mathematically perfect world of virtual reality, not the actuality of an imperfect physical world. Even if ball-trackers could overcome the sort of inaccuracies related to fast ball speeds and slow camera frame-rates the goal of complete accuracy will always be beyond reach. Here it is suggested that the purpose of technological aids to umpires and referees be looked at in a new way that takes the viewers into account.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

Recently considered modifications to public policy and trends in technology transfer practices have underscored the need for validated instruments to assess the maturity of technologies. This paper details a study that aimed to develop and present a generalized technology readiness level (GTRL) scale that a variety of professionals and researchers could use to assess the maturity of technologies in a range of contexts. Of particular interest is developing and validating an instrument that technology transfer professionals in federal laboratories, universities, and the private sector in the United States of America can use to assess the maturity of technologies to facilitate their technology transfer efforts. The primary goal of the research study was to highlight the need for validated measurement instruments for assessing the maturity of technologies in these contexts, test methods for validating the GTRL scale and other readiness level scales, and fill the knowledge gap regarding methods for properly validating such instruments. This included producing insights to inform future efforts to validate the GTRL scale as well as efforts to develop and validate other instruments to measure technology maturity. The study provides specific recommendations relevant to determining the face validity, content validity, inter-rater reliability, and intra-rater reliability of the GTRL scale and other such instruments for assessing technology maturity.

Research into health, particularly social and psychological health, is crucial. Ultimately, an in-depth understanding of social and psychological health will more than promote well-being. Technology research is indispensable, particularly concerning health and the built environment, given the need to create holistic and supportive frameworks for well-being. Moreover, because literature reviews establish the foundation for academic inquiries, they provide valuable overviews for foresight into grey research areas, particularly multi-disciplinary research like health technology and the built environment. Hence, this study aims to discover the existing themes on health, technology, and built-environment nexus subjects while revealing the grey areas and suggesting proactive areas for future research. The objectives drove this aim to: 1. investigate the implications of technology for the social and psychological dimensions of health; 2. uncover the likelihood of a nexus between health, technology, and the built environment; and 3. highlight new research perspectives for the concluding seven years of the SDGs (2024–2030). The review results highlighted ten themes around which a nexus exists between health, technology, and the built environment; they also pointed out new research perspectives for the next seven years (up to 2023).

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in the rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments of Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reducing surface runoff during rainy season.

This study aims to unravel the paradox of perceptions and knowledge of the flood victims towards the causes of the disaster in both internal and external context. Internal context comprises of a comparison of perceptions and knowledge based on individual characteristics (age, gender, education and income). Whereas, the external context includes the factors of the awareness of the victims towards the amount of rainfall, the impact of land use changes as well as the negligence of the responsible parties. The main objective of this study is to determine the differences of perception and knowledge of December 2014 flood victims in Kelantan towards the factors that lead to the flood. This disaster had resulted in huge amount of money loss as well as traumatize the victims in which can be felt to this day. Since that incident, there were various points of view and different perceptions in finding the cause of the disaster occurred. Besides that, the study found that the level of perception and knowledge as to the cause of the disaster is different in the internal context (individual characteristics). This difference has a significant influence on the awareness of the causes of the floods that occurred in the external context. Significant relationships at the level of p <0.05 has existed between perception and knowledge of the causes of the disaster victims affected by environmental changes in the last 10 years. This indicates that although the victim is aware of the physical environment changes happening around them, but all that is seen as not a major contributing factor to the cause of the floods in Kelantan in 2014.

The Silk Road pattern (SRP) and Circumglobal teleconnection pattern (CGT) are two well-known teleconnection patterns along the Eurasian westerly jet during boreal summer, which are often regarded as one teleconnection pattern. In view of the distinct features of the SRP/CGT on the interannual (IA) and interdecadal (ID) timescales, the present study investigates the linkages and differences between the SRP and CGT on the two timescales. On the IA timescale, the SRP and CGT feature a similar circumglobal wave train structure with strong and significant centers over Eurasia, but show clear independences. Specifically, the SRP and CGT illustrates largely the mid-/high-latitude-related and tropics-related parts of the Northern Hemisphere upper-tropospheric circulation variations, respectively. Also, the CGT shows a stronger connection to the Indian summer monsoon (ISM) heating and El Niño–Southern Oscillation than the SRP, which makes the CGT more like a tropical-forcing-driven atmospheric mode but the SRP more like an internal atmospheric mode. The linkages and differences between them are associated with their asymmetry relationship during their positive and negative phases, which are attributed mainly to the asymmetry impact of the ISM heating/cooling on the Eurasian circulations. On the ID timescale, the SRP and CGT are characterized by a coherent two-wave train structure over Eurasia, and feature more like the same teleconnection pattern, which are associated with the Pacific Decadal Oscillation and Atlantic Multidecadal Oscillation. The present findings on the linkages and differences between the SRP and CGT are helpful to understand the variability and prediction of the SRP and CGT.

Microarray gene expression analysis is a powerful technique used in cancer classification and research to identify and understand gene expression patterns that can differentiate between different cancer types, subtypes, and stages. However, microarray databases are highly redundant, inherently nonlinear, and noisy. Therefore, extracting meaningful information from such a huge database is a challenging one. The paper adopts the Fast Fourier Transform (FFT) and Mixture Model (MM) for dimensionality reduction and utilizes the Dragonfly optimization algorithm as the feature selection technique. The classifiers employed in this research are Nonlinear Regression, Naïve Bayes, Decision Tree, Random Forest and SVM (RBF). The classifiers' performances are analyzed with and without feature selection methods. Finally, Adaptive Moment Estimation (Adam) and Random Adaptive Moment Estimation (RanAdam) hyper-parameter tuning techniques are used as improvisation techniques for classifiers. The SVM (RBF) classifier with the Fast Fourier Transform Dimensionality Reduction method and Dragonfly feature selection achieved the highest accuracy of 98.343% with RanAdam hyperparameter tuning compared to other classifiers.

The economic development and infrastructure of a nation are closely interrelated. In addition, public trust in national infrastructure facilities is closely linked to the preservation of the advantages provided by these facilities to the public. Since the 1970s, Korea has achieved exponential economic growth over a short period of time and the number of infrastructure facilities has increased correspondingly. This compressed economic development has been underpinned by the national infrastructure, whose safety and usability have been excluded from the scope of the development. However, after around 30 years, structural deterioration coupled with general insensitivity to safety in today’s society has considerably reduced public trust in using the infrastructure. Realistically, policies that mainly focus on developing new technologies related to infrastructure construction have led to practical limitations that discourage the development of technologies for maintenance or inspection. Furthermore, current maintenance works face certain limitations caused by various reasons: insufficient budget, increasing number of infrastructure facilities requiring maintenance, shortage of manpower, and rapidly increasing number of aging infrastructure facilities. To overcome these limitations, a new approach is required that is different from general inspection methods under the existing rules and regulations. In this context, this study aimed to explore the efficiency of bridge inspection and maintenance by unmanned aerial vehicles (UAVs) that could observe inaccessible areas, could be conveniently and easily controlled, and could offer high economic benefits. To this end, various tests were performed on elevated bridges, and suitable UAV images were obtained. The obtained UAV images were inspected by using machine vision technology, thereby excluding subjective evaluations by humans. Methods for enhancing the objectivity of the inspection were also discussed. The test results showed that both the efficiency and objectivity of the proposed method were better than those of the existing bridge maintenance and inspection methods.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

The research paper investigates the synthesis of metal matrix composites (MMCs) through the amalgamation of aluminum and silicon carbide particles, employing a two-step mixing methodology called the stir casting method. Metal matrix composites are materials that enhance the capabilities of a metallic matrix by incorporating another material. This leads to better characteristics such as tensile and shear moduli, fatigue and fracture properties, thermal expansion coefficient, and more. Aluminum-matrix composites are a class of materials that possess distinct characteristics that may be modified by altering factors such as the type of reinforcing material, the amount of reinforcement, and the fabrication technique employed to produce the composite. The concept aims to combine the desirable properties of metals and ceramics by incorporating durable refractory particles into a malleable metal structure. The fabrication process employs the stir casting technique, where reinforcing phases are mechanically stirred into a molten matrix to create cast composites with reinforcement volume percentages of up to 30%. The study utilizes Response Surface Methodology to enhance the mechanical properties of the composites through the optimization of manufacturing parameters, including stirring temperature, time, and speed. The study entails analyzing the correlation between different casting conditions and the resulting changes in hardness and tensile strength.

The adoption of health information technology (HIT) has increased considerably, contributing to better communication between physicians and patients and providing technological bases for learning and institutional improvement. This type of technology brings many challenges; therefore, understanding its adoption and assimilation is important to assess its potential for engendering desirable outcomes in health management. The assimilation of health information systems should be highlighted as their importance in health organisations is now recognised as a key facilitator assisting in providing better health outcomes. Thus, this study aimed to analyse HIT adoption based on models such as Technology, Organisation and Environment (TOE), which analyses at the organisational level, with other models, such as the Technology Acceptance Model (TAM), which analyses at the individual level, and the assimilation of the adopted technologies.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

CO2 has characteristic properties and reactions at converter smelting temperature, and the chemical reaction between CO2 and elements such as C and Si in the molten pool has bubble proliferation and cooling effects, which can effectively improve the kinetic and thermodynamic conditions of converter smelting. Here, an experimental study and industrial test on the application of CO2 in converter smelting were carried out. The smelting effects of Mode-1 and Mode-2 with total CO₂ injection amounts of 229 Nm³ and 196 Nm³, respectively, were compared, and the changes in molten steel and slag compositions, dust removal, and gas are analyzed. The test results show that converter top and bottom blowing CO₂ technology (COMI-B)technology had significant metallurgical advantages over the N-Mode; the dephosphorization rate increased by 4.2%, slag (FeO) content was reduced by 2.04%, end point nitrogen content of molten steel was reduced by 20%, gas recovery increased by 8.29 Nm³/t, and soot production reduced by 14.7%. The results of the study provide reference for the application of COMI-B technology in converters in the iron and steel industry and develop a new path for resource utilization of CO₂.

This study explores the elements that influence consumer vegetarian diet choices in parts of South Korean provinces. The study examines these explanatory variables: ethical-animal-welfare, health, environment, social issues , mood-emotion, and religious-beliefs with vegetarianism serving as the dependent variable. The Likert scale data from 264 respondents were analyzed using logistic regression analysis. Results show that health, ethical-animal-welfare ideals as well as environmental concerns emerge as significant variables influencing the decision to embrace a vegetarian diet. This shows that consumers (international students) in Korea are becoming more aware of and concerned about health, ethical and sustainable dietary choices. Secondly, health plays a crucial role in the vegetarian diet selection, indicating that health-conscious people are more inclined to choose a vegetarian lifestyle. Religious belief and mood have various degrees of influence on the vegetarian diet decision. The findings of this study have consequences for consumer behavior, marketing managers, and decision-makers. Businesses in the food industry, in particular, can gain from catering to the needs and tastes of consumers that prioritize ethical-animal welfare ideals, as well as those that value health and environmental sustainability. Creating and advertising vegetarian and vegan choices in local restaurants can effectively attract and serve this specific target demographic.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Technological advancements in the Internet of Things (IoT), unmanned aerial vehicles (UAVs), and novel technological tools have transformed disaster management practices from localized approaches to a global framework. These innovations necessitate a unified understanding and application of diverse methodologies at an international level, ensuring they are accessible and operational across different sectors. This integration is crucial not only for technical personnel but also for medical teams, who play a pivotal role in disaster response and management. By fostering a comprehensive grasp of these methods, we can enhance coordination, efficiency, and effectiveness in addressing disasters on a global scale. The authors aimed to provide a comprehensive overview of emerging techniques that are driving shifts in strategic approaches and treatment technologies. Recognized as a domain of continuous research and development, this overview, by necessity, remains an incomplete snapshot of an evolving field. It highlights the dynamic nature of technological and strategic advancements, underscoring the importance of ongoing investigation and innovation to stay abreast of current trends and future directions. The article also highlights the importance of international collaboration beyond societal and national boundaries A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

The bioindicator potential of seagrass ecosystems in coastal trace metal monitoring is low for tropical island ecosystems. This study evaluated the bioindicator potential of six seagrass species exposed to anthropogenic trace metal pollution in the Andaman and Nicobar Islands (ANI) of India. Sediment and seagrass biomass, samples were analyzed for trace metals (Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb, Zn) from four locations of ANI exposed to anthropogenic contamination. Geo accumulation Index values indicated moderate trace metal contamination in seagrass sediment. Seagrass trace metal accumulation from sediment was both species-specific and location- specific for ANI. Small seagrass species such as H. ovalis, H. beccarii and H. uninervis accumulated the maximum concentration of six trace metals (Cr, Cu, Fe, Ni, Pb, Zn) in their tissues compared to big seagrass species like T. hemprichii and E. acoroides of ANI. This study indicates leaves of small seagrass and roots of big seagrass species can serve as short- and long-term bioindicators respectively, of coastal trace metal contamination in tropical islands of ANI.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

Malaria is one of the leading causes of illnesses and deaths in Africa at large and Nigeria in particular, especially amongst pregnant women and children under the age of five years. Our research revealed that though the government has deployed so many intervention systems to contend with this death-causing vector—the mosquitoes, malaria related deaths (MRDs) have continued to increase. This is because people have not sufficiently adopted those intervention systems to protect themselves. Further enquiries into the ineffective compliance of the people to the intervention systems revealed that the interventions are passive in nature. Based on these, we set up three measurable research outcomes to enable us to determine the appropriateness of persuasive technology in solving the malaria problem. We technically avoided a one-size-fits-all design approach and adopted Participatory System Design (PSD) and User-Centered Design (UCD) approaches in our system design methodologies. Well-structured questionnaires were used to extract information from the participants. The data obtained from the research survey was used in modeling the intervention system. The research was conducted in three phases: baseline, development and deployment of an intervention system—the Malaria Prevention and Control Support System (MPCSS), and an evaluation study to determine the performance of the intervention system. The research led to the following achievements: (1) encouraged an increase in the number of people who participated in malaria prevention and control activities by lowering the rate of malaria cases from 96.9% to 68.5% and increasing ownership of mosquito nets from 54% to 85.5%; (2) demonstrated that persuasive technology could be used to increase public awareness and knowledge of a given subject as noted in our evaluation result; and (3) demonstrated that persuasive technology is a veritable active intervention to combat malaria.

Agriculture is an industry that heavily relies on the environment. The increasing frequency of ex-treme disasters attributable to climate change has adversely affected agricultural land and dis-rupted the stability of the supply of agricultural products. Therefore, we implemented a research program focused on current strategies for adapting to agricultural meteorological disasters. The primary goal was to actively promote disaster prevention information and techniques through information platforms and applications and to provide refined forecasting and an early warning system to enhance preparedness for and recovery from agricultural disasters. This initiative can transform passive mitigation into dynamic action by disseminating crucial information to farmers. We integrated meteorological data and crop characteristics to develop disaster prevention strate-gies for the predisaster, during-disaster, and postdisaster stages to empower farmers to implement autonomous disaster prevention, ensuring their profitability and minimizing the impact of disas-ters. This paper presents an agricultural disaster prevention system involving cross-disciplinary collaboration to establish an early warning system for crop disasters. However, the effectiveness of the early warning system relies on the availability of complete meteorological and crop infor-mation, necessitating high-density agricultural meteorological stations, refined weather forecast services, historical crop damage data, and ongoing research and development on disaster preven-tion technology. In the system, a diversified social media interface is used to provide local farmers with weather forecast information. When impending disasters are identified, the platform acti-vates disaster prevention measures to reduce agricultural losses. This article paper introduces Taiwan’s agricultural disaster prevention system as a complete disaster prevention strategy.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

Medical data flows in streams as the data related to clinical tests and administered drugs by the doctors flows continuously. The doctors must be immediately alerted if negative associations are found among the drugs they prescribe. Data streams are to be processed in single scans as it is not possible to re-scan the data for any iterative processing. To detect negative drug connections, regular and frequent drug patterns must be processed. Negative correlations between disease-curing medications might create adverse responses that kill patients. This paper proposes an algorithm that finds the negative associations among regular and frequent patterns mined from medical data streams. The negative associations mined are the most effective and reduce the negative associations, which are more critical by 50%.

{Background}: to develop a technology for hydrothermal processing of oilseeds and primary pressed cake in order to obtain functional vegetable oils from non-traditional oilseeds (melon and watermelon seeds). {Methods:} Analyses of mint, pulp, oils and cakes obtained from them were carried out in accordance with the methodology described in the "Manual on research Methods, technochemical control and accounting of production in the fat and oil industry". {Results:} Technological parameters of hydrothermal treatment of crushed oilseeds from melon and watermelon seeds before primary and final pressing are investigated. {Conclusions:} An advanced double pressing technology has been developed, which provides grinding of seeds without separating the husk up to 60% when passing through a sieve with a diameter of 1 mm, humidification with steam condensate up to 11% and heat treatment at a temperature of 80℃ for 50 minutes before pre-pressing and grinding up to 60% of the patency of the pre-pressed cake, moistening the material to a humidity of 12% steam at a temperature of 120 ° C and a pressure of 0.5 MPa for 30 minutes before distillation.

In light of the urgency raised by the COVID-19 pandemic, global investment in wildlife virology is likely to increase, and new surveillance programs will identify hundreds of novel viruses that might someday pose a threat to humans. Our capacity to identify which viruses are capable of zoonotic emergence depends on the existence of a technology—a machine learning model or other informatic system—that leverages available data on known zoonoses to identify which animal pathogens could someday pose a threat to global health. We synthesize the findings of an interdisciplinary workshop on zoonotic risk technologies to answer the following questions: What are the prerequisites, in terms of open data, equity, and interdisciplinary collaboration, to the development and application of those tools? What effect could the technology have on global health? Who would control that technology, who would have access to it, and who would benefit from it? Would it improve pandemic prevention? Could it create new challenges?

The rapid growth of the Information and Communications Technology (ICT) sector requires additional infrastructure, such as more micro-datacenters and telecom stations, to support the higher internet speeds and low latency requirements of 5G net-works. The increased power requirements of the new ICT technologies necessitate the proposal of new power supplies in an attempt to retain the increase in energy demand and running costs. This work provides an in-depth theoretical analysis on the losses of the individual stages of commercially available PSU and proposes a new multicell PSU, Buck-PFC converter, which offers a higher overall efficiency at varying load levels. The theoretical results are verified using simulation results, via PSIM Thermal Module, and using experimental data. The results indicate that multi-cell structures can improve the overall PSU ef-ficiency by 1.2% at 50% rated power and more than 2.1% at full power. Finally, taking into consideration the economic implica-tions of this study, it is shown that the proposed multicell structure may increase the PSU costs by 10.78% but the payback pe-riod is in the order of just 3.3 years.

With the rapid development of global offshore wind power, the demand for offshore wind power operation and maintenance is also increasing. Wisdomization of offshore wind farms is a practical need to improve the operation level and benefit of offshore wind farms. This paper first introduces the current development situation and characteristics of global offshore wind power, and expounds the current situation and main challenges of offshore wind power operation and maintenance market. Therefore, our paper discusses the innovation of offshore wind power operation and maintenance from the aspects of operation and maintenance management of offshore wind power, monitoring and analysis technology of units, far-reaching wind field monitoring and operation and maintenance risks. Then, combined with information technology and lean management concept, a smart operation and maintenance management platform for wind farms in far-reaching sea areas is built to explore centralized and intelligent operation and maintenance management mode, improve operation and maintenance efficiency of wind farms in far-reaching sea areas, and minimize operation and maintenance costs. Finally, through the research on the characteristics of 5G technology, combined with the practical experience of operation and maintenance, and in view of the characteristics of offshore wind farms, we analyze and propose several typical application scenarios of 5G technology in the intelligent operation and maintenance of offshore wind farms, which provides a new solution for the efficient operation and maintenance of offshore wind farms.

The transition to sustainable mobility is a recognized socio-economic and environmental challenge, particularly among young adults in low- and middle-income countries (LMICs). This paper addresses the lack of comprehensive research on mobility patterns for LMICs by examining the travel patterns of students, staff, and lecturers at the National Advanced School of Public Works, Yaoundé (NASPW) to understand transport mode choices and barriers to the use of public and active transport modes. Data was collected through online questionnaires from 425 participants. Findings revealed that most students (27.5%) used multiple modes of transport, with moto-taxis being the most common (21%). Lecturers primarily used private cars (50%), while staff relied on taxis or multiple modes (33%). Accessibility, vehicle speed, and flexibility appeared as the most important reasons for the preferred modes of transport. Barriers included long waiting times and traffic congestion for public transport, and distance and inadequate infrastructure for active mobility. The usage of public transportation was encouraged by its affordability and reduced travel time, whilst active options were preferred due to their cost savings and health benefits. To promote sustainable mobility for campus travel, it is crucial to encourage active modes, develop mass transport systems, and raise awareness through symposiums and conferences among students and staff.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

In today's digital landscape, cybersecurity has become a priority, with attacks becoming increasingly sophisticated. Traditional security approaches are no longer enough, requiring a more dynamic and advanced response. In this context, integrating Artificial Intelligence (AI) and Machine Learning (ML) appears key to addressing this growing threat. However, despite their high effectiveness, there is a developed problem: the integration of various data sources and technologies for comprehensive protection. This article presents an in-depth review of integrating Artificial Intelligence and Machine Learning in cybersecurity, focusing particularly on Open Extended Detection and Response (Open XDR) technology. The literature review in this article was meticulously conducted with specific criteria in mind. It focused on sourcing peer-reviewed journals, authoritative cybersecurity publications, and recent conferences that primarily concentrate on the advancements in AI and ML within the cybersecurity domain, particularly from 2018 to 2023. This timeframe was chosen to ensure the inclusion of the most current and relevant developments in Open XDR technology, Intrusion Detection Systems, Endpoint Detection and Response, and Security Information and Event Management systems. Additionally, the review gave special attention to studies and reports highlighting practical implementations and real-world applications of these technologies, thereby ensuring a comprehensive understanding of their impact and effectiveness in enhancing cybersecurity resilience. The methodology used is a detailed literature review, examining how various cybersecurity components interact and function. These components include Intrusion Detection Systems (IDS), which monitor networks for malicious activities; Endpoint Detection and Response (EDR), which focuses on detecting and investigating security incidents on endpoints; and Security Information and Event Management (SIEM), systems that provide real-time analysis of security alerts. The review also considers the role of Active Directory, a directory service for Windows domain networks, and the process of log forwarding, where log files are transmitted to a central server for analysis, in the context of AI and ML. The paper delves into the development of AI and ML, underscoring their roles in cybersecurity for advanced data processing, pattern recognition, and predicting threats. It explores both supervised (where the model is trained on labeled data) and unsupervised learning (where the model learns from unlabeled data) in ML, and how these techniques bolster cybersecurity measures. The article highlights the significance of Open XDR as a critical innovation that integrates data from multiple sources for comprehensive security analysis. Further, the review discusses how the integration of AI and ML into various cybersecurity tools, such as IDS, EDR, and SIEM, augments capabilities in threat detection and response. It addresses the challenges and opportunities that AI and ML present in the cybersecurity domain, focusing on ethical issues, data privacy concerns, and the necessity for ongoing professional development in this rapidly advancing field. The paper concludes by affirming the effectiveness of merging AI and ML with these cybersecurity tools within the Open XDR framework.

Migraine is one of the leading causes of disability worldwide [1,2]and patients with acute migraine frequently present to emergency departments (ED)[3]. The current literature suggests that ED treatment of migraine headache varies across institutions [4-7]. Considering this, we conducted a scoping review to summarize trends in medication prescribing patterns for acute migraine treatment in the ED setting. Trends were evaluated for factors influencing treatment choices, with particular attention placed on opioids and migraine specific therapy. This scoping review was based on the Arksey and O'Malley methodological framework[8]and included studies published between 1 January 2000 until 31 May 2020. 14 publications met the inclusion criteria. The most common classes of medication prescribed were often anti-emetics or Non-steroidal anti-inflammatory drugs (NSAID), but rates varied between studies. There was a concerning trend towards an underutilization of triptans and overutilization of opiates. The use of specific clinical goals of treatment (e.g. two-hour pain free freedom response) was also not evident. Additionally, 88% (n=8) of the 9 studies commenting on adherence to hospital or evidence-based guidelines stated that practices were non-adherent. Overall, the reviewed literature reveals treatment practices for acute migraine in the ED are heterogeneous and deviate from established international recommendations.

This study investigates the specific factors affecting the usage intention of distributed ledger technology (DLT), such as availability, diversity and economic value from the perspective of a unified theory of technology acceptance. Users of DLT in public and private sectors were surveyed. Availability and economic value affect performance expectancy, while availability, diversity, and profitability have an influence on effort expectancy. Performance expectancy and transparency have a positive effect on the intention to use DLT which in turn exerts a positive effect on usage behavior. This study provides implications for researchers in that it attempts to investigate the factors affecting the usage intention of DLT based on the extended unified theory of acceptance and encompassing diverse industries that adopt DLT, such as the public, financial, medial, and logistics sectors.

This project designed a set of network security mechanisms for cloud applications in VANETs. At present, cloud computing is one of the government’s development priorities in the industry. We divide cloud into public, private, and hybrid clouds in this project. Vehicles or passengers can access road conditions or public transport information through the public cloud; public transportation can access current driving records and users can access relevant enterprise information on the private cloud and hybrid cloud is a combination of public and private clouds. Both cloud computing or VANETs require network and information security. At present, many researches on VANETs security only focus on message communication, and neglect information storage. Researches on cloud computing security only focus on information protection, and neglect user privacy and anonymity. This project designed a set of network and information security mechanisms in line with the requirements of Confidentiality, Authentication, Non-repudiation, Conditional Anonymity, and Conditional Untraceability. This project primarily needs to achieve the following: 1.an authentication mechanism to verify the identity of each other between the passenger and the vehicle and to verify the identity with Single Sign-On; 2. vehicle or user privacy and anonymity, which need to be able to replace the anonymous ID and related parameters for the vehicle or the user; 3. a private communication mechanism, which enables any vehicle or user to communicate privately; and 4. an information security encryption method, which can encrypt the information on a cloud server to avoid unauthorized access by internal personnel or hackers.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

Since the advent of the Internet, there has been a significant shift from wired to wireless communication between devices. The volume of data transmitted has surged, primarily driven by the exponential growth of network services, Internet of Things (IoT) devices, and online users. This trend became especially pronounced with the onset of the COVID-19 pandemic, as the Internet's role and significance expanded dramatically. People began to spend more time online, engaging in activities like e-learning, remote work, and online shopping. Concurrently, concerns about the security of wireless communication channels have escalated. As more data is stored and transmitted over the Internet, cybercriminals are actively seeking unauthorized access to it to further their malicious objectives. Through a comprehensive literature review in the realm of wireless network security and privacy, it has become evident that several factors render these networks susceptible to vulnerabilities. The aim of this paper is to shed light on the major and common security and privacy challenges faced by existing wireless networks. Additionally, it seeks to demonstrate the array of techniques available to mitigate these issues. Ultimately, this paper will culminate in an in-depth analysis of cybersecurity measures to address the issues in wireless networks.

The opportunities and advantages of implementing Artificial Intelligence (AI) and Machine Learning (ML) to optimize the process control of wastewater treatment in the Oil and Gas industry are discussed in this work. Discussion is centered around five major points: 1) Various types of Oil and Gas wastewater (Sour, Oily, Produced) and industry standards/methods for treatment, including specific case studies and challenges when treating certain wastewater. This section aims at the common types of wastewater in the Oil and Gas industry and how they are generally treated. 2) How AI/ML has been implemented in wastewater treatment in various industries; summary of which AI/ML languages were used along with a brief overview of how they work. This article focused on an understanding of the specific case studies and AI explanations to understand the effectiveness of wastewater treatment using AI/ML. 3) AI that is currently implemented in Oil and Gas such as personal protective equipment (PPE), smartwatches radiofrequency identification etc. This showed that AI/ML already plays a successful role in the Oil and Gas industry and has proven to help optimize many processes and components. Many of these AI/ML implementations are now industry standards and have greatly benefitted the industry. This section demonstrates that the implementation and the use of AI/ML have been proven to be a successful endeavor and that expanding the role of AI/ML would be beneficial. 5) Using the established points from the previous sections the paper outlines why AI/ML is ideal for Oil and Gas wastewater treatment; this argument centers around fit-for-purpose treatment, and the possible uses of the treated water. A determination of the best-suited AI languages, possible implementation scenarios, and how this would shift the way Oil and Gas industries treat and approach wastewater is presented to the reader.

Type 1 diabetes (T1D) has shown an increase in the incidence rate of about 3% per year over the last two decades. Continuous Insulin Subcutaneous Therapy (CSII) is widely used in the paediatric population with diabetes; however, it requires more preparation by the treating team and careful selection of potential users. Prescriptive provisions vary from Region to Region and the perspective of health workers still remains an unexplored area. The aim of the research project is to explore the representations of a group of diabetologists and psychologists working in pediatric diabetology on the national territory, regarding roles, functions and activities as part of a multidisciplinary team; their views on the potential benefits of CSII and the types of individuals applying for the use of technology. A socio-anagraphic data sheet was administered and two homogeneous focus groups were conducted by profession; they were audio recorded. The transcripts produced were analysed using the Emotional Text Mining (ETM) methodology. Each of the two corpus generated three clusters and two factors: for diabetologists, a focus on the patient in different levels of care emerged, collaborating both with other health professionals and with the territory, through the proposal of an intervention where the medical aspect is often represented by technology; also for psychologists there was a representation of interdisciplinary networking, with a greater focus on the processes inherent the management of pathology, from acceptance to the elaboration and integration of diabetes in the family narrative. The understanding of the representations of health professionals working in pediatric diabetes about new technologies can contribute to the consolidation of a network of professionals through a targeted work on possible critical issues emerged.

This article is an effort to scrutinize the role of Information Technology development in the chronological transformation of Urban Planning domain using the exploratory research approach. In this research, it is argued that the theoretical and practical understanding of Urban Planning should absorb and integrate the bright outcome of the rise of Information and Technology to foster congruent future urban development. The article addresses the trends of transformation in the urban planning domain through the myopic lens of the expansion of information and communications technology era followed by investigating the key drivers shaping the interaction between modern-day urban planning and information technology considering both the dark and bright sides into account.

The feeling of beauty is one of the positive human feelings. In architecture and design, it is associated with forms appropriate to their purpose. The usefulness of products to meet needs is also important. They are well received by users. The task of designers is to achieve perfection in their work. The rational design and use of artificial living environments are expressions of concern for natural resources (sustainable environment). These issues are addressed, i.e., by an interdisciplinary initiative of the New European Bauhaus. The aim of the paper is to expand knowledge about beauty and utility. They are important when choosing mass-produced goods. The article uses research methods: interpretive research, analyses, comparisons, logical argumentation, etc. Experimental qualitative research using a checklist was used. The results expand the knowledge on the selected topic and research scope of the research of the paper. The survey can be used to rationally evaluate architecture, interiors, and design facilities. It can be helpful for various aesthetic and functional strategies dedicated to different users. The paper demonstrates the role of beauty and functionality in the built environment. They are analyzed in the context of social and technical conditions, as well as contemporary sustainable design

The legume-rhizobia symbiosis is one of the most important plant-microbe interactions in sustainable agriculture due to its ability to provide much needed N to cropping systems. This interaction is mediated by the mutual recognition of signaling molecules from the two partners, namely legumes and rhizobia. With legumes, these molecules are in the form of flavonoids and anthocyanins, which are responsible for the pigmentation of plants parts, such as seeds, flowers, fruits and even leaves. Seed coat pigmentation in legumes is a dominant factor influencing gene expression relating to N2 fixation, and may be responsible for the different N2-fixing abilities observed among legume genotypes under field conditions in African soils. Cowpea, Kersting’s bean and Bambara groundnut landraces with black seed coat color are reported to release higher concentrations of nod-gene-inducing flavonoids and anthocyanins when compared to the Red and Cream landraces, hence the black seed coat pigmentation is considered a biomarker for enhanced nodulation and N2 fixation. Cowpea, Bambara groundnut and Kersting’s bean with differing seed coat colors are known to attract different native soil rhizobia, confirmable by PCR-RFLP analysis of bacterial DNA from root nodules of these legumes. Even when seeds of the same legume with diverse seed coat colors were planted together in one hole, the nodulating bradyrhizobia clustered differently in the PCR-RFLP dendrograms. In one study, Kersting’s groundnut, Bambara groundnut and cowpea with differing seed coat colors were selectively nodulated by different bradyrhizobial species. Multilocus sequence analysis showed that different Bradyrhizobium species nodulated the Kersting's bean based on seed coat color. Phylogenetic analysis also placed the bradyrhizobial isolates in close proximity to different Bradyrhizobium species such as B. vignae 7-2T, B. subterraneum 58 2-1T, B. kavangense 14-3T, B. liaoningense 2281 (USDA 3622)T, B. yuanmingense LMG 21827T, B. huanghuaihaiense CCBAU 23303T, B. pachyrhizi PAC48T, and a reference type strain of B. elkanii according to seed coat color. Using 16S rDNA amplicon sequencing, we also found significant selective influences of seed coat pigmentation on microbial community structure in the rhizosphere of five Kersting’s groundnut landraces. For example, the rhizosphere of Belane Mottled landrace was dominated by Proteobacteria, while Bacteroidetes dominated the rhizospheres of the other landraces. With legumes, seed coat pigmentation therefore plays a dominant role in the selection of the bacterial symbiotic partner.

The aim of this study was to evaluate the challenges basic school tutors face when integrating Information and Communication Technology (ICT) into their instructing and learning activities and to recommend possible strategies for addressing those challenges. This study employed an interpretive paradigm and a qualitative method approach to analyze the challenges basic school teachers face when integrating ICT into teaching in an emerging country, particularly Ghana. The participants of this study were chosen using purposive and snowball sampling techniques. A total of twenty (20) respondents were chosen for this study. The study found that teachers, despite their challenges, had a strong desire to integrate ICT into their instruction and learning activities. These challenges are the limited number of ICT tools and the absence of fully-subscribed software package that runs on them, the lack of electrical outlets in some classrooms, poor internet connectivity and power fluctuation. These teachers also had to deal with challenges like Trojan horses and spam despite the slow internet connectivity. The study suggested that basic school management should procure modern ICT tools and fully-subscribed software package to expand the school's ICT infrastructure giving teachers the choice to choose the ICT tools they will integrate into their teaching and learning activities for the successful integration of ICT into instruction and learning activities. Again, school management should ensure teachers are given basic training regarding ICT and its incorporation into tuition and learning activities to acquire the necessary competencies, understanding, and attitudes that will enhance teaching and learning activities.

Background: We aimed to describe the patterns, management, and outcome of traumatic femoral shaft fractures. Methods: An observational descriptive retrospective study was conducted for all trauma patients admitted with femoral shaft fractures between January 2012 and December 2015 at the only level 1 trauma center and tertiary hospital in the country. Data were analyzed and compared according to the time to intramedullary nailing, mechanisms of injury and age groups. Main outcomes included in-hospital complications and mortality Results: A total of 605 cases were analyzed, with mean age of 30.7±16.2 years. The majority of fractures were unilateral (96.7%) and 91% were closed fractures. Three-fourth of fractures were treated by reamed intramedullary nailing (rIMN); antegrade in 80%. The pyriform fossa nails were used in 71.6% while trochanteric entry nails were used in 28.4%. Forty-five (8.9%) of fractures were treated with external fixator, 37 (6.1%) had conservative management. Traffic-related injuries occurred more in patients aged 14-30 years whereas; injuries related to fall were significantly higher in patients aged 31-59 years. Thirty-one patients (7.8%) had rIMN < 6 h post-injury, 106 (25.5%) had rIMN < 6-12 h and 267 (66.8%) had rIMN > 12 h. The implant type, duration of surgery, DVT prophylaxis, in-hospital complications and mortality were comparable among the three treatment groups. Conclusion: In our center, the frequency of femoral fracture is 11% which mainly affects severely injured young males due to traffic-related collisions or falls. Further multicenter studies are needed to reach a consensus for the appropriate management based on the location and timing of injury

In this paper, a low-power Injection-Locked Clock and Data Recovery (ILCDR) using 28nm FDSOI technology is presented. The back-gate auto-biasing of UTBB-FDSOI transistors allows us to create a QRO (Quadrature Ring Oscillator) reducing both size and power consumption. By injecting a digital signal into this circuit, we realize an Injection-Locked Oscillator (ILO) with low jitter. Thanks to the good performance of this oscillator, we propose a low power ILCDR with fast locking time and low jitter for burst-mode applications. The main novelty consists in the implementation of a complementary QRO based on back-gate control using FDSOI technology to realize a simple and efficient ILCDR circuit. With a Pseudo-Random Binary Sequence (PRBS7) at 868Mbps, the recovered clock jitter is 26.7ps (2.3%UIp-p) and the recovered data jitter is 11.9ps (1%UIp-p). With a 0.6V power supply, the power consumption is 318μW. The estimated Chip area is around 6600μm².

Quantum cell automata (QCA) is a nanotechnology that uses a transistor-free structure to design digital circuits and overcome the limitations listed for CMOS circuits. The computing circuits that make up the bulk of computers can be designed and using this technology. Subtractors are a big part of computational circuits. This research deals with the design of a subtractor that due to the innovation in the design of this circuit and the novel arrangement of quantum cells of its kind has caused the number of cells used in the design of the circuit to reach its lowest value compared to previously designed circuits. The size of the circuit as well as the loss power are minimized compared to the circuits designed by the subtractors. Another trait clears of this circuit compared to many previous designs is its single-layer design, which reduces latency and noise in the output waveform. The circuit designed by the QCADesigner simulator is tested and simulated inadition the results are displayed in the simulated waveform. Also, the results of calculations for power dissipation in each QCA cell were evaluated by QCAPro software, which is a powerful tool for estimating power loss simulation. It has less implementation and level (single layer) than Previous designs.

Diabetes mellitus (DM) has been defined as a group of metabolic diseases characterized by hyperglycemia resulting from defects in insulin secretion, insulin action, or both. This study includes (84) subjects, their age ranged from (40 to 54) years. (20) subjects were healthy chosen as control group and (64) patients with type 2 diabetes mellitus were divided into three groups according to their type of anti diabetic therapy: (23) newly diagnosed group without therapy (Group1), (20) with metformin therapy (Group2) and (21) with metformin plus glibenclamide therapies (Group3). In the study lipid profile level were quantitatively determine by enzymatic methods, in addition to that fasting plasma glucose (FPG), Glycated hemoglobin (HbA1c%) and body mass index (BMI) were identified in the patients. There is significant increase in the level of lipid profile in patients group. Metformin alone produce a non-significant favorable effect on all lipids profile parameters while metformin plus glibenclamide showed a significant reduction in TC and LDL-C.

Technology is in the way to reaching in its climax but the basic understanding of science in many phenomena is still awaited. Scientific research reveals strong analogy between electron and photon. Atoms that execute suitable electronic transitions, on absorbing heat energy at shunt level, excite their electrons. De-excitation of an electron under the gravitational force of its nucleus, where inertia is involved, results depicting energy in the shape like Gaussian distribution. The wavelength of photon remains in inter-state electron’s gap where the source of generating energy in wave-like fashion is due to electronic transitions under confined electron-dynamics; energy configures under electron’s trajectory in the excitation period is due to inertia-levitation-inertia behaviours while energy configures under electron’s trajectory in the de-excitation period is due to inertia-gravitation-inertia behaviours. Silicon atom is a model system of it. Uninterrupted confined inter-state electron-dynamics results into configure energy in a wave-like fashion that can travel immeasurable length and on interruption from the point of generation, it becomes a photon. Such photons increase wavelength on decreasing energy while travelling through inherently built gap of splitted inert gas atoms where they give light (glow) on reaching wavelength in the visible range. Here, I discuss that heat energy is due to merged photons, photons characteristic current are due to photons having wavelength in inter-state electron’s gap and light is due to photons, following the wavelength in the visible range. Force of repulsion or attraction in certain materials engages the phenomenon of levitism or gravitism where inertia is exempted. All structural motifs and dynamics are subjected to characteristic photons as long as atoms are under neutral behavior of field force. A structural design delivers straight-forward application on dealing photons at different wavelengths. Here, materials science explores matter at electronic level while absorbing heat energy and generating photon energy. Thus, devise science to describe.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

This study investigates aspects of job retention and business growth in small- and medium-sized enterprises (SMEs). It examines how employers think about retention policy in relation to business growth, in contrast to previous studies’ main focus on employee motivation, job retention, and turnover. Qualitative semi-structured interviews were conducted face-to-face with Chief Executive Officers (CEOs) of Engineering and Informational Technology SMEs in South Korea. The results show that an important factor influencing job retention policies of SMEs is the motivation of employees to make voluntary effort, rather than offering them additional financial rewards or using other Human Resource Management (HRM) practices to improve individual performances. Interviewees believed that job retention and business growth are closely related and they discussed various ways of eliciting emotional contributions from employees. Unlike research on larger firms, these suggestions did not involve financial rewards. How employers think about the roles played by employees strongly influences their firm’s productivity and competitiveness. The SME CEOs examined in this study considered this issue central to their firm’s survival and growth. This study suggests SME employers adjust their retention policy correspondingly.

This study delves into the critical domain of public procurement, specifically focusing on Sustainable Public Procurement (SPP) and Environmental, Social, and Governance (ESG) considerations within the context of South Korea. The aim of this research is to empirically scrutinize the factors influencing the impact index of SPP, with a particular emphasis on services related to labor standards. The investigation spans three years, from January 1, 2019, to July 31, 2021, encompassing state agency orders and post-implementation legal changes. Leveraging the comprehensive Korea On-line E-Procurement Sys-tem(KONEPS) platform, we meticulously collected data, ultimately culminating in 21,573 services meeting our criteria, from which 250 cases underwent an in-depth analysis. The study sheds light on the influence of social responsibility evaluation cri-teria on overall procurement scores, while also uncovering the moderating effects of various factors. The outcomes of this study offer valuable insights into the impact index of social responsibility evaluation criteria within South Korea's public procurement landscape. Factors including procurement year, classification, service period, and estimated price were identified as significant influencers. Moreover, the number and location of evalu-ation criteria items, inclusion of sincerity elements, and the evaluating agency were deemed pivotal determinants of the influence index. These findings hold profound implications for policymakers, procurement practitioners, and researchers and provide a roadmap for optimizing the utilization of social responsibility evaluation criteria to advance responsible and sustainable procurement practices. Future research avenues include conducting further study of additional moderat-ing variables, expanding datasets to encompass a broader spectrum of procurement contexts, and evaluating the long-term repercussions of social responsibility evaluation on procurement outcomes. These endeavors promise to further refine and advance public procurement practices in South Korea and beyond.

Malaysian healthcare institutions still use ineffective paper-based vaccination systems to manage childhood immunization schedules. This may lead to missed appointments, incomplete vaccinations, and outbreaks of preventable diseases among infants. To address this issue, we proposed a text messaging vaccination reminder and recall system named Virtual Health Connect (VHC) to simplify and accelerate the immunization administration for nurses that may result in improving the completion and timeliness of immunizations among infants. Considering the narrow research about the acceptance of these systems in the healthcare sector, we examined factors influencing nurses’ attitude and intention to use VHC using the extended technology acceptance model (TAM). The novelty of the conceptual model is proposing new predictors of attitude, namely, perceived compatibility and perceived privacy and security issues. We conducted a survey among 121 nurses in Malaysian government hospitals and clinics to test the model. We analyzed the collected data using partial least squares-structural equation modeling (PLS-SEM) to examine the significant factors influencing nurses’ attitude and intention to use VHC. Moreover, we applied artificial neural network (ANN) to determine the most significant factors of acceptance with higher accuracy. Therefore, we could offer more accurate insights to decision-makers in the healthcare sector for the advancement of health services. Our results highlighted that the compatibility of VHC with the current work setting of nurses developed their positive perspectives toward the system. Moreover, the nurses felt optimistic about the system when considering it to be useful and easy to use in the workplace. Finally, their attitude toward using VHC played a pivotal role in raising their intention. Based on the ANN models, we also found that perceived compatibility was the most significant factor influencing nurses' attitude towards using VHC, followed by perceived ease of use and perceived usefulness.

Recent years have experienced an increase in construction and demolition waste (C&amp;DW), which is the most significant solid waste stream. C&amp;DW is contributing to exceeding all planetary boundaries and presents a range of other issues. In order to better understand the existing research on C&amp;DW, a global bibliographic analysis was undertaken through seven groups of keyword searches and the results visualised using VOCviewer. The results show that C&amp;DW receives only a modest research attention compared to other areas of waste, and this is despite an exponential increase in C&amp;DW research since 2016. The analyses also show that concrete is the most researched material in terms of C&amp;DW, and that reuse, recycling, and circular economy are so far attracting only proportionally modest research attention. This signals a need for further acceleration of the C&amp;DW research, and specifically for more research on reuse, recycling, and circular economy for materials other than concrete.

Blockchain technology can achieve decentralization, multi-party verification, anti-tampering, anonymity, traceability of transactions, and the application of distributed ledger. Countries around the world continue to seek the blockchain business models, technologies and applications, and have different visions and policies for the development of blockchain. This study conducts a comparative policy framework of theoretical analysis of the blockchain technology between the USA and China. Using the innovative policy tools proposed by Rothwell and Zegveld, the above mentioned governments are analyzed from the viewpoint of twelve policy tools. The results show that the USA and China all prefer to use “Environmental-side” policy. The USA has paid more attention to “Legal and regulatory”, “Public services” and “Procurement”. China has the highest proportion of policies in “Political tools”, followed by “Legal & regulatory”, while “Scientific and technical”, “Education” and “Overseas agent” come in third . The blockchain technology has developed vigorously among industries and its applications have gradually diversified. The results are provided to various stakeholders as a reference for policy planning.

The paper presents the design and the implementation of different advanced control strategies that are applied to a nonlinear model of a thermal unit. A data–driven grey–box identification approach provided the physically meaningful nonlinear continuous–time model, which represents the benchmark exploited in this work. The control problem of this thermal unit is important since it constitutes the key element of passive air conditioning systems. The advanced control schemes analysed in this paper are used to regulate the outflow air temperature of the thermal unit by exploiting the inflow air speed, whilst the inflow air temperature is considered as an external disturbance. The reliability and robustness issues of the suggested control methodologies are verified with a Monte–Carlo analysis for simulating modelling uncertainty, disturbance and measurement errors. The achieved results serve to demonstrate the effectiveness and the viable application the suggested control solutions to air conditioning systems. The benchmark model represents one of the key issues of this study, which is exploited for benchmarking different model–based and data–driven advanced control methodologies through extensive simulations. Moreover, this work highlights the main features of the proposed control schemes, while providing practitioners and heating, ventilating and air conditioning engineers with tools to design robust control strategies for air conditioning systems.

The Industrial Internet of things (IIoT) enabled smart system has entered into a golden era of rapid technology growth. IIoT is a concept to make every system interrelated such that they are able to collect and transfer data over a wireless network without human intervention. In this paper, we discuss the development of an IoT enabled system to monitor the vibration signature of equipment as part of prognosis and availability management system (P&AM) that serves to prevent unplanned operation downtime and catastrophic failure of a whole system. In order to simply the complexity of processing video content and performing inference, the Intel OpenVINO platform was selected because of it’s simplicity, portability across Intel AI processors, performance and comprehensiveness of it’s analytical and diagnostics capabilities that can be tested in Intel’s DevCloud. The IIoT system consists of a High Performance Computing (HPC) platform based on Intel’s Xeon processors and Movidius AI accelerator, Intel’s OpenVINO toolkit for AI, a Regul high performance programmable controller capturing vibration data through sensors and a low-latency network connection. Notifications of anomalies are sent to a smartphone. This paper reveals an approach for the features extraction and selection, known as feature engineering, of the equipment component we want to protect. Feature engineering is the first step for the P&AM of these components and extends to the whole system. The broader aim of this paper is to help technical leaders at the exploring or experimenting stages of their AI framework to learn the concepts of implementing algorithms using datasets that have real value to their companies. Datasets generated and referred to in this paper were generated by simulation under various material failure scenarios.

All types of sports are potential application scenarios for automatic and real-time visual object and event detection. In rink hockey, the popular roller quad skate variant of hockey team sports, it is of great interest to automatically track player’s movements and positions, player’s sticks and, also, making other judgments, such as being able to locate the ball. In this work, we introduce a real-time pipeline composed by an object detection model, created specifically for rink hockey games, followed by a knowledge-based event detection module. Even in the presence of occlusions and quick motions, our deep learning object detection model effectively identifies and tracks, in real-time, important visual elements such as: ball; players; sticks; referees; crowd; goalkeeper; and goal. Using a curated dataset composed by a collection of videos of rink hockey, comprising 2525 annotated frames, we trained and evaluated the algorithm performance and compare it to state of the art object detection techniques. Our object detection model, based on YOLOv7, presents a global accuracy of 80%, and presents a good performance in terms of accuracy and speed, according to our results, making it a good choice for rink hockey applications. In our initial tests, the event detection module successfully detected one important event type in rink hockey games, the occurrence of penalties.

Despite the important role of offshore renewable energies in the energy transition, the economical viability is still unclear. Therefore, an appropriate site selection is crucial. Besides the energy potential, the impact of operation and maintenance (O&M) aspects on the location can be critical. Traditional accessibility assessment metrics do not allow a comprehensive evaluation. Therefore, the present paper suggests a novel, technology-informed metric, incorporating the overall set of most critical aspects, i.e. metocean conditions, visibility due to sunlight and sea fog, system failures, and O&M logistics. Among the different aspects, limited visibility is shown to be highly relevant with a reduction of up to 60% in accessibility. The study assesses accessibility in 5 different locations across Europe. On the one hand, accessibility is shown to be less sensitive to long-term resource variations with a reduction of 5% in the last 6 decades. On the other hand, accessibility is shown to be inversely proportional to the energy potential overall, meaning that as energy potential increases, accessibility is reduced, increasing downtime, reducing final energy generation and increasing the final cost of energy. As a consequence, site selection should combine energy potential and accessibility assessments, which is enabled by the technology-informed metric presented here.

Virtual reality (VR) technology gains theoretical support from rehabilitation and pedagogical theories and offers a variety of capabilities in educational and interventional contexts with affordable products. VR is attracting increasing attention in the medical and healthcare industry as it provides fully interactive three-dimensional simulations of real-world settings and social situations, which are particularly suitable for cognitive and performance training including social and interaction skills. The worldwide rising trend in the prevalence of autism spectrum disorder calls for innovative and efficacious techniques for assessment and treatment. The article offers a summary of current perspectives and evidence-based applications of VR technology as an educational and intervention tool for individuals with autism spectrum disorder, with a primary focus on social communication including social functioning, emotion recognition, and speech and language. Technology- and design-related limitations as well as the disputes over the application of virtual reality to autism research and therapy are discussed and future directions of this emerging field are highlighted with regards to application expansion and improvement, technology enhancement, and the development of brain-based research and theoretical models.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

Organ-on-a-chip (OOC) is an emerging technology that simulates an artificial organ within a microfluidic cell culture chip. Current cell biology research focuses on in vitro cell culture due to various limitations of in vivo testing. Unfortunately, in vitro cell culture fails to provide an accurate microenvironment, and in vivo cell culture is expensive and has historically been a source of ethical controversy. OOC aims to overcome these shortcomings and provide the best of both in vivo and in vitro cell culture research. The key component of the OOC design is utilizing microfluidics to ensure a stable concentration gradient, dynamic mechanical stress modeling, and accurate reconstruction of a cellular microenvironment. OOC also has the advantage of complete observation and control of the system, which is impossible to recreate in in vivo research. Multiple throughputs, channels, membranes, and chambers are constructed in a polydimethylsiloxane (PDMS) array to simulate various organs on a chip. Various experiments can be performed utilizing OOC technology, including drug delivery research and toxicology. Current technological expansions involve multiple organ microenvironments on a single chip, allowing for studying inter-tissue interactions. Other developments in the OOC technology include finding a more suitable material as a replacement for PDMS and minimizing artefactual error and non-translatable differences.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

The burgeoning field of Urban Air Mobility (UAM) promises transformative solutions to urban transportation challenges, with the potential to revolutionize cargo logistics in metropolitan areas. This research investigates the role of tiltrotor technology as a pivotal enabler of seamless UAM integration for efficient cargo transportation within urban environments. The study delves into the existing challenges within UAM, such as infrastructure limitations and the need for adaptable aerial vehicles that can navigate confined spaces while maintaining payload capacity. Tiltrotor Unmanned Aerial Vehicles (UAVs) are examined as a solution to these challenges due to their unique capabilities, combining vertical takeoff and landing (VTOL) with efficient forward flight. This research evaluates the potential of tiltrotor UAVs for urban cargo transportation, focusing on their operational efficiency, safety, and economic viability. Furthermore, the study explores the potential impact of tiltrotor technology on urban cargo logistics, considering factors such as reduced congestion, shorter delivery times, and environmentally sustainable operations. Real-world case studies and practical implementation strategies are discussed, shedding light on the importance of integration of tiltrotor UAVs into existing cargo transportation networks.The findings of this research underscore the transformative potential of tiltrotor technology in enhancing UAM for cargo transportation within urban areas. The study contributes valuable insights to the ongoing discourse on UAM integration and lays the groundwork for future developments in autonomous aerial cargo delivery systems.

After reviewing the history of the struggle between human beings and plant diseases, insects and weeds, especially reviewing the thoughts of plant protection in ancient Chinese agricultural books, the target recognition of plant pests and the six types of plant protection methods and 36 subdi-vision measures were summarized. Then the development overview of pesticide application technology was focused and reviewed systematically by combining the development timeline of pesticide application and the key technologies including the performance measurement and the simulation and modeling of pesticide spraying system. And three suggestions for further research were proposed from the perspectives of human-being and environmental health, the sustainable and eco-friendly application medium, and the efficiently application equipment system in plant protection.

Good health and well-being is one of the essential SDGs that ensure healthy lives and promote well-being for all ages and further entails providing substantial medical services to the public at low cost and with minimal adverse effects on the environment. Information and communication technologies (ICTs) have taken on an increasingly important function as significant facilitators of healthcare reform, with the goals of enhancing access to health services, the quality of treatment provided, and the overall productivity of the healthcare system. However, the integration of ever-increasing ICT technologies into the healthcare systems, also referred to as digital transformation, is not a straightforward process, but it comes with different types of challenges from integration level to application design level and security level. Although several studies have been proposed to address the integration of ICT technologies into healthcare systems, there is still a need for a comprehensive research study on the integration and design challenges, security and privacy challenges, application areas, and possible positive and negative impacts. Therefore, this paper contributes as the research literature study covering an important SDG, "Good health and well-being," and its digital transformation, along with summarising our research findings in a detailed and taxonomical way. To start with, firstly, we present a detailed comparison of existing studies on healthcare and well-being, mainly focusing on integrating ICT technologies in healthcare in terms of sustainable aspects, security and privacy challenges, design and integration challenges, E-health-related applications, and future directions. We also present an overview and the need for digital transformation in healthcare, discuss its significant components, highlight E-health's importance and benefits, explore its integration and design challenges, and categorise the security and privacy challenges. Next, we present an in-depth discussion on the role of Blockchain technology as today's leading technology in E-health, discussing Blockchain technology and its characteristics, highlighting its benefits, and describing the possible types of Blockchain-based E-health use cases. Furthermore, we discuss the positive and negative impact of ICT integration along with identifying open issues and challenges of integrating ICT technologies into the healthcare systems and discuss future research directions, which provide the strength for researchers to address the issues in future solutions.

Analysis of immediate effects of the COVID-19 pandemic on SMEs in Rwanda aims to assess and quantify the economic and financial impacts of the pandemic during the lockdown and presents options adopted by SMEs to reopen their business opera-tions. It also seeks to recommend options for sustainable and resilient economic recovery from the scars of COVID-19. This analysis used data collected from nearly 220 SMEs located across the country and applied an Exploratory Data Analysis (EDA) and multivariate linear regression models to measure the pandemic effects. The study revealed that firms downsized employment by 36.4 per cent, but data depict significant deviation within SMEs by their size. The COVID-19 pandemic has had a greater magni-tude of negative effects on sales levels among small businesses. Tax amounts were reduced amidst the crisis however, data do not show any significant variations among SMEs. Additionally, SMEs owners applied various coping mechanisms during re-opening. The study used firm-level data, providing detailed and reliable effects of the shocks on business performance. This analysis recommends establishing the medium-term financing and technical support for SMEs to ensure steady and sustainable recovery from pandemic effects as well as strengthening their resilience to any other socio-economics shocks.

The worldwide population is undergoing a fundamental change in its age structure, which challenges the health and social services system. The need to migrate towards a more person-centered and coordinated model of care that supports the optimization of abilities and capacities for older people has to be matched. In this sense, eHealth technologies can play a fundamental role. In this paper, through a questionnaire-based data collection on 30 primary (older people) and 32 secondary (informal caregivers) end-users, we share the sustainable way to develop a product optimizing the user experience and ensuring adoption. Both older adults and caregivers consider the use of smartphone and smartwatch to be very important, but also the use of digital devices for healthcare can be helpful. Seniors care about self-monitoring of health parameters using wearable devices, regardless of their health status, and would like to be included in the process of making good health decisions, because they need to feel in control of their healthcare process. Digital solutions in health and care can support the wellbeing of older adults in many areas of their daily lives at home and in their communities, but only if such innovation is designed around the natural voice of the intended target.

Achieving the dual development of rural revitalization and urbanization is an important strategic goal of China’s current modernization. Rural population and settlements are the main components of the countryside in traditional agricultural areas, and play an important role in the development of the countryside itself in terms of urban and rural land use and in the formation of urban and rural development patterns. This study analyzes the spatial and temporal changes in rural populations and settlements at the township level, as well as the degree and type of coupled development. A framework for urban–rural development relationships based on different types of coupled development is proposed, and a model of urban–rural forces is constructed to derive the spatial pattern of urban–rural development at the township level that may be formed in the future. Our study shows that the rural population and settlements in the study area are characterized by significant spatial and temporal dynamics, indicating that traditional rural areas are in a process of rapid development and change. The results of the township-level coupling measurements present four types of development in terms of the spatial pattern of urban–rural development: A-type is most likely to produce new cities or satellite towns in the Jixi–Harbin–Qiqihar area in the future; B-type is the fastest dying area in the future, located in the Harbin and Qitaihe clusters, with a tendency to merge into Harbin; C-type is the area to be focused on in the future to attract population and strictly control the growth of the rural settlement area to avoid it turning into B-type; D-type may develop regional township centers in the future in the combined area of Jiamusi City, Suihua City and Mudanjiang City. The results of the study provide experience in realizing rural revitalization according to local conditions. The new spatial pattern of urban–rural development provides an important reference for formulating land use policies, optimizing urban–rural land allocation and realizing integrated urban–rural development strategies.

The study evaluated the association between nutrient patterns and body fat and regional adiposity in middle-aged black South African (SA) men and women and determined if this differed by sex. Body fat and regional adiposity (dual-energy x-ray absorptiometry), and dietary intake (7-day quantified food frequency questionnaire) were measured in black SA men (n=414) and women (n=346). Using principal component analysis, nutrient patterns were computed from 25 nutrients in the combined sample. Four nutrient patterns were extracted, explaining 67% of the variance in nutrient intake. Animal and fat, as well as the vitamin C, sugar and potassium driven patterns, were positively associated with total adiposity. In contrast, the retinol and vitamin B12 pattern was associated with the centralisation of fat. Notably, the strength of the association between the animal-driven nutrient pattern and BMI was greater in men (1.14 kg/m2, 95%CI (0.63-1.66)) than women (0.81 kg/m2, 95%CI (0.25-1.36)) (Pint=0.017). In contrast, the plant driven pattern was associated with higher abdominal subcutaneous adipose tissue (SAT) in women (44 cm2, 95%CI (22-67)) but not men (Pint =1.54 x 10-4). These interactions suggest that although men and women have similar nutrient patterns, the associations with the whole body and regional body fat are different.

The contribution of extra-tropical synoptic cyclones to the formation of summer-mean atmospheric circulation patterns in the Arctic is investigated by clustering the dominant Arctic circulation patterns by the self-organizing maps (SOMs) using the daily mean sea level pressure (MSLP) in the Arctic domain (≥ 60°N). Three SOM patterns are identified: one with prevalent low pressure anomalies in the Arctic Circle (SOM1) and two opposite dipoles with primary high pressure anomalies covering the Arctic Ocean (SOM2 and SOM3). The time series of summertime occurrence frequencies demonstrate the largest inter-annual variation in the SOM1, the slight decreasing trend in the SOM2, and the abrupt upswing after 2007 in the SOM3. The relevant analyses with produced cyclone track data confirm that the vital contribution. The Arctic cyclone activity is enhanced in the SOM1 because the meridional temperature gradient increases over the land–Arctic Ocean boundaries co-located with major extra-tropical cyclone pathways. The composite daily synoptic evolutions for each SOM reveal that the persistence of all the three SOMs is less than 5 days on average. These evolutionary short-term weather patterns have substantial variability at inter-annual and longer timescales. Therefore, the synoptic-scale activity is central to forming the seasonal-mean climate of the Arctic.

No research to date has explored the possibility of context-specific, within-relationship fluctuation in attachment security. In this present article, two cross-sectional studies were designed (1) to develop and validate context-specific attachment scales in Traditional-Chinese, and (2) to explore fluctuations in within-parent attachment security between the contexts of sport and academics, in relation to global attachment patterns and indicators of psychological wellbeing. Results indicated that youth can and do perceive within-parent attachment patterns differently depending upon context but that the relationship of such differences to context-specific outcomes is complex. Of particular interest was that the degree of within-parent attachment variability between contexts was clearly and negatively related to indices of psychological wellbeing. This suggests that contextual variation may be a meaningful and useful way to explore within-parent attachment fluctuation.

In the present study, the problem of the sulfuric acid recycling from spent copper plating solution was solved using a hybrid membrane technology, including diffusion dialysis and electrodialysis. A real solution from the production of copper-coated steel wire, containing 1.45 mol/L of sulfuric acid, 0.67 mol/L of ferrous sulfate and 0.176 mol/L of copper sulfate was processed. Diffusion dialysis with anion-exchange membranes was used to separate sulfuric acid and salts of heavy metals. Then purified dilute sulfuric acid was concentrated by electrodialysis. Energy consumption for sulfuric acid electrodialysis concentration at a current density of 400 A/m2 was 162 W·h/mol with current efficiency 16 %. After processing according to the hybrid membrane scheme, the solution contained 1.13 mol/L sulfuric acid, 0.077 mol/L ferrous sulfate and 0.022 mol/L copper sulfate. The resulting acid solution with a small amount of ferrous sulfate and copper sulfate met the established requirements for a copper plating bath solution and can be reused in production.

Background: The use of technology in paediatrics is increasing, and new health technology will change the way in which paediatric care is delivered in the future. This review is part of the Royal College of Paediatrics and Child Health Paediatrics 2040 project, which is developing a credible vision for the future of paediatrics in the UK. Aims: To summarise the impact of health technology on the delivery of paediatric care over the last ten years. To learn from existing technology use and make recommendations for future implementation. Methods: A search strategy was developed and two databases (Cochrane Library and PubMed) were systematically searched in August 2019 for relevant publications in English. Searches were limited to papers published between January 2009 and August 2019 (with further rapid review of papers published between September 2019 and November 2020). We included papers that studied young people up to the age of 24 or on those providing care for this population. A thematic synthesis of the data from the included studies was undertaken using seven domains of paediatric care. Results: 128 studies were included, grouped by domain of care. Most included studies were defined as digital (n=55) or communication (n=37). Studies looked at the different types of health technology used within different domains of care, including secondary and tertiary care (n=39), public health and prevention (n=29), and community (n=20). Studies were assessed on delivery of care outcomes using positive, negative, mixed and no effect. The most common outcomes reported were adherence and satisfaction. Discussion: This review highlights the growing importance of technology in delivering paediatric care. Six themes emerged: the importance of clear guidelines, continuity of care, confidentiality and privacy, digital poverty, using a personalised approach, and using technology to supplement rather than replace. In future, technology development should involve the end user throughout the design process.

This paper used the decolonial theory to analyse provision of Assistive Technology and assistive devices at an institution of higher education in South African. It was an empirical study, in which data were collected through interviews with students with disabilities and the Disability Rights Centre staff members. The paper sought to understand the invisible hidden implications of provision of Assistive Technology and assistive devices. The finding was that it is students with disabilities who were provided with Assistive Technology and assistive devices at the institution. The institution provided them through the Centre, to support their learning. However, this way of provision was found to be stigmatising and segregative. Furthermore, while the provision on one hand enabled students with disabilities’ learning, on the other, it constrained it. The argument of the paper is that when provision of Assistive Technology and assistive devices is for a particular group of students it defeats the whole purpose for it is intended, and could hinder rather than promote learning. It is hoped that the paper will contribute to contemporary debate on provision of Assistive Technology and support services for people with disabilities in low resource settings, from a South African context specifically, and in higher education broadly.

Mallard (Anas platyrhynchos) are currently one of the most popular species in rare bird breeding in several southern provinces of China, but there are very few studies on the gut microbial communities of domestic and wild mallards. In this study, 16S rRNA gene high-throughput sequencing technology was used to compare the composition and diversity of gut microbial communities in domestic and wild mallards. Alpha diversity analysis revealed significant differences in the gut microbial communities of domestic and wild mallards. Beta diversity analysis showed that the two groups of stool samples were mostly separated on the principal coordinate analysis (PCOA) plot. In domestic mallards, Firmicutes (67.97%) was the most abundant bacterial phylum, followed by Proteobacteria (24.48%), Bacteroidetes (3.13%), Fusobacteria (2.21%), and Actinobacteria (1.10%). The dominant bacterial phyla in wild mallards were Firmicutes (79.02%), Proteobacteria (12.85%), Fusobacteria (3.37%), and Bacteroidetes (2.79%). At the genus level, a total of 10 dominant genera (Streptococcus, Enterococcus, Clostridium, Lactobacillus, Soilbacillus, Bacillus, Acinetobacter, Comamonas, Shigella, and Cetobacterium) with an average relative abundance greater than 1% were detected in the fecal samples of both groups. The average relative abundance of five potential pathogens (Streptococcus, Enterococcus, Acinetobacter, Comamonas, and Shigella) was higher in domestic mallards than in wild mallards. The enrichment of pathogenic bacteria in the intestinal tract of domestic mallards should be of sufficient concern.

Mallard (Anas platyrhynchos) are currently one of the most popular species in rare bird breeding in several southern provinces of China, but there are very few studies on the gut microbial communities of domestic and wild mallards. In this study, 16S rRNA gene high-throughput sequencing technology was used to compare the composition and diversity of gut microbial communities in domestic and wild mallards. Alpha diversity analysis revealed significant differences in the gut microbial communities of domestic and wild mallards. Beta diversity analysis showed that the two groups of stool samples were mostly separated on the principal coordinate analysis (PCOA) plot. In domestic mallards, Firmicutes (67.97%) was the most abundant bacterial phylum, followed by Proteobacteria (24.48%), Bacteroidetes (3.13%), Fusobacteria (2.21%), and Actinobacteria (1.10%). The dominant bacterial phyla in wild mallards were Firmicutes (79.02%), Proteobacteria (12.85%), Fusobacteria (3.37%), and Bacteroidetes (2.79%). At the genus level, a total of 10 dominant genera (Streptococcus, Enterococcus, Clostridium, Lactobacillus, Soilbacillus, Bacillus, Acinetobacter, Comamonas, Shigella, and Cetobacterium) with an average relative abundance greater than 1% were detected in the fecal samples of both groups. The average relative abundance of five potential pathogens (Streptococcus, Enterococcus, Acinetobacter, Comamonas, and Shigella) was higher in domestic mallards than in wild mallards. The enrichment of pathogenic bacteria in the intestinal tract of domestic mallards should be of sufficient concern.

Mediterranean coastal lagoons and their peripheral areas often provide a collection of habitats for many species, and they often face significant threats from anthropogenic activities. Diverse human activities in such areas directly affect the spatio-temporal dynamic of surface water and its ecological characteristics. Monitoring the surface water dynamic, and understanding the impact of human activities are of great significance for coastal lagoon conservation. The Regional Natural Park of Narbonne includes a typical Mediterranean lagoon complex where surface water dynamic and its potential link with local diverse human activities has not yet been studied. In this context, based on all the available Landsat images covering the study area during 2002-2016, this study identified the water and non-water classes for each satellite observation by comparing three widely used water indices (i.e., NDVI, NDWI and MNDWI) and using the Otsu method. The yearly water frequency index was then computed to present the spatio-temporal dynamic of surface water for each year, and three water dynamic scenarios were also identified for each year: permanent water (PW), non-permanent water (NPW) and non-water (NW). The spatial and inter-annual variation in the patterns of the three water scenarios were characterized by computing the landscape metrics at scenario-level quantifying area/edge, shape, aggregation and fragmentation. Finally, the quantitative link between different land use and land cover (LULC) types derived from the LULC maps of 2003, 2012 and 2015 and the surface water dynamic scenarios was established in each of the 300 m x 300 m grid cells covering the study area to determine the potential impact of human activities on the surface water dynamic. In terms of the inter-annual variation during 2002-2016, PW presented an overall stability, and NPW occupied only a small part of the water surface in each year and presented an inter-annual fluctuation. NPW had a smaller patch size, with lower connectivity degree and higher fragmentation degree. In terms of spatial variation during 2002-2016, NPW often occurred around PW, and its configurational features varied from place to place. Moreover, PW mostly corresponded to natural lagoon, and salt marsh (as a part of lagoons), and NPW had a strong link with arable land (agricultural irrigation) and salt marsh (salt production), sand beach/dune, coastal wetlands and lagoon for the LULC maps of 2003, 2012 and 2015. However, more in-depth analysis is required for understanding the impact of sand beach/dune, coastal wetlands and lagoon on surface water dynamics. This study covers the long-term variations of surface water patterns in a Mediterranean lagoon complex having intense and diverse human activities, and the potential link between LULC types and the water dynamic scenarios was investigated on different dates. The results of the study should be useful for environmental management and protection of coastal lagoons.

Providing data on usage patterns is key to assessing the reduced-risk potential of novel tobacco and nicotine products at a population level. We performed a nationwide cross-sectional survey of the general population in Japan to assess usage patterns after the introduction of tobacco heating products (THPs). Eligible participants were Japanese residents, aged 20 years or older who consented to complete the survey. Individuals living in institutions were excluded. A three-stage probability sampling method was applied that was geographically stratified by street blocks proportionate to population density. Respondents self-reported patterns of product use and reasons for THP use. Complete responses were available from 5,306 individuals, of whom 933.5 (17.6%) were current users, 984.2 (18.5%) were former users and 3388.4 (63.9%) were never users of tobacco products. Cigarettes were used by 14.6% of current tobacco product users and THPs by 5.3%. Cigarettes and THPs were used exclusively by 64.5% and 12.2%, respectively, and both were used by 12.7%. The most common reasons reported for THP use were perceived reduction in harm to self and others compared to cigarettes. While the prevalence of cigarette use in Japan is decreasing, THPs seem to be increasingly used as long-term alternatives to cigarette smoking.

Background: In this study, we aimed to evaluate the effect of s-FLT-1 and PlGF concentrations in women in the first trimester of pregnancy on the pulsatility index of the ductus venosus and the right and left uterine arteries. Methods: A total of 108 pregnant women in their first trimester were included in the study, with 87 assigned to the experimental group and 21 to the control group. Ultrasound examination were performed to measure the uterine artery pulsatility index, resistance index, ductus venosus pulsatility index, and blood sampling levels of biomarkers such as b-HCG; PAPP-A; s-FLT-1 and PlGF. Results: There was a significant negative relationship between PAPP-A concentration and the risk of fetal growth restriction, and a significant negative relationship between PlGF concentration and the risk of preeclampsia and fetal growth restriction in women in their first trimester of pregnancy. There was also a significant positive relationship between sFLT-1/PLGF ratio and the risk of developing preeclampsia. No significant relationships were found between the concentrations of biomarkers beta-HCG, PAPP-A, sFLT-1, PlGF, and any of the parameters PIUARt, PIUALt, Mean uterine arteries, and DVPI. Summary: In conclusion, this study did not find conclusive evidence to support the hypothesis that beta-HCG, PAPP-A, s-FLT-1, and PlGF concentrations in women in the first trimester of pregnancy have a significant effect on the Pulsatility Index of the ductus venosus and the Right and left Uterine Arteries. Further research is needed to investigate these potential associations.

Major (exo)planetary and satellite bodies seem to concentrate at intermediate areas of the radial 1 distributions of all the objects orbiting in each (sub)system. We show that angular-momentum transport during secular evolution of (exo)planets and satellites necessarily results in the observed intermediate accumulation of the massive objects. We quantify the ‘middle’ as the mean of mean motions (orbital angular velocities) when three or more massive objects are involved. Radial evolution of the orbits is expected to be halted when the survivors settle near mean-motion resonances and angular-momentum transfer between them ceases (gravitational Landau damping). This dynamical behavior is opposite in direction to what has been theorized for viscous and magnetized accretion disks, in which gas spreads out and away from either side of any conceivable intermediate area. We present angular momentum transfer simulations in few-body systems, and we calculate the tidal dissipation timescales and the physical properties of the mean tidal field in planetary and satellite (sub)systems.

Abstract: The human race has always innovated, and in a relatively short time went from building fires and making stone-tipped arrows to creating smartphone apps and autonomous robots. Today, technological progress will undoubtedly continue to change the way we work, live, and survive in the coming decades. Since the beginning of the new millennium, the world has witnessed the emergence of social media, smartphones, self-driving cars, and autonomous flying vehicles. There have also been huge leaps in energy storage, artificial intelligence, and medical science. We are facing immense challenges in global warming and food security, among many other issues. While human innovation has contributed to many of the problems we are facing, it is also human innovation and ingenuity that can help humanity deal with these issues “New directions in science are launched by new tools much more often than by new concepts. The effect of a concept-driven revolution is to explain old things in new ways. The effect of a tool-driven revolution is to discover new things that have to be explained”. (F. Dyson, 1997 In this article, we review the impact of technology as evolving at beginning of 21st Century on future prospect of Energy demand either renewable or non-renewable form, Economy, to Ecommerce, Education and any other E-related of Modern Technology.

Duct-dependent lesions are classically divided into duct dependent pulmonary circulation which involves severe right sided obstructive lesions such as pulmonary atresia or critical stenosis, and duct dependent systemic circulation which is characterized by malformation of the left side of the heart, and whose severest spectrum is hypoplastic left heart syndrome. Dextro-transposition of the great arteries remains in gray zone between being included in some old classifications as a duct dependent pulmonary circulation lesion or a new category of duct-dependent or independent mixing lesion. We hypothesize that re-classifying duct dependent congenital defects into duct dependent perfusion and oxygenation offers a model to fit D-TGA into the same category of right sided obstructive lesions and reflects the clinical spectrum in a more comprehensive way.

Waste biogenic materials from seafood exploitation are valuable resources of new compounds exploitation within the blue bioeconomy concept. Here, we describe the effectiveness of Raman technology implementation as an in-line tool for demineralization process control of crustaceans or gastropods. We produced transparent chitin polymer foils from three waste crustacean shells (C. sapidus, S. mantis and M. squinado) using a slow, green chemical approach employing acetic acid, and showed the progressive process of biogenic carbonate dissolution and increasing the Raman characteristic signal of chitin, in a time dependence manner. It turned that chitin foils obtaining is species-specific, and the demineralization bath of waste shell mixture can be effectively tracked by Raman spectroscopy, for solvent control and the recovery of the calcium acetate as valuable by-product. Comparatively, calcium acetate drug, a compound widely used in kidney failure diseases, or as additive in nutraceuticals and food industry, has been obtained here, following a green demineralization path of the sea snail Rapana venosa intact shell, assisted by Raman tech-nology, using 9% acetic acid (vinegar) solution for 14 days. To validate the final products identity and quality, The process of waste shells demineralization and the final products of the treatment were investigated using various Raman techniques and technologies, cross-validating the results with FT-IR, XRD and SEM-EDX techniques. NIR Raman spectroscopy revealed chitin bands in a time-dependent manner, while Resonance Raman spectroscopy showed the preservation of ca-rotenoids after two weeks of acetic acid treatment. A hand-held flexible TacticID Raman system with a 1064 nm excitation demonstrated its effectiveness as a rapid, in-line decision making tool during process control and revealed excellent reproducibility of the lab-based instrument signal, suitable for in situ evaluation of the demineralization status and solvent saturation control. The calcium acetate recovered from residual treatment solutions was assessed regarding its hydration status, purity, and suitability as recrystallized material for further use as pharmaceutical product or ingredient in complex formulations.

The globe and more particularly the economically developed regions of the world are currently in the era of the fourth Industrial revolution (4IR). Conversely; the economically developing regions in the world and more particularly the African continent have not yet even fully passed through the Third Industrial Revolution (3IR) wave and its economy is still heavily dependent on the agricultural field. On the other hand, the state of global food insecurity is worsening on an annual basis thanks to the exponential growth of the global human population which continuously heightens the food demand in both quantity and quality. This justifies the significance of the focus on digitizing agricultural practices to improve the farm yield to meet up with the steep food demand and stabilize the economy of the African continent and countries like India whose economy is mainly dependent on Agriculture. The tools we have at our disposal to utilize in the digitization of farming practices include space technology and Global Navigation and Satellite System (GNSS) in particular, Machine learning (ML), precision agriculture and communication systems such as the Internet of Things (IoT) and Information And Communication Technologies (ICT). The most pressing challenges in the farming field include the monitoring of diseases, pests, weeds and nutrient deficiencies in the crops as early detection translates to swift and timely correction actions and hence more yield at the end of a farming cycle. Vast opportunities in the field of precision agriculture still exist that can amount to further research studies such as the lack of real-time monitoring and real-time corrective action focus.

Cooking is a very decentralized and private way of energy consumption in human activities. The existing investigation and statistical analysis can’t effectively calculate the proportion of population relying on clean cooking fuel and utilization technology in the region. Therefore, based on the big data of the earth, this paper adopts the combination of spatial analysis and statistical analysis to determine the survey sample area, and according to the economic conditions, topographic characteristics, national policies for new energy construction and living habits of the provinces and cities under investigation, the questionnaire survey is conducted for the research area to calculate the proportion of the regional population relying on clean cooking fuels and utilization technologies. Taking the south of the Yangtze River in China as an example, the paper effectively calculates that 88.25% of the population depends on clean cooking fuel and technology in this region, of which 89.81% are in urban areas and 79.87% are in rural areas. Analysis of the survey data shows that the proportion of the population using clean cooking fuels and technologies is related to factors such as economic development, income and resource endowment. There is a large urban–rural gap in terms of energy consumption tendency and structure in the south of the Yangtze River in China and cooking energy consumption in rural households also varies from region to region. The technical ideas and conclusions of the paper have high reference application value, which can help promote the upgrading of clean energy utilization and provide data basis for relevant decision and policy making.

Due to the complexity, high-risk, and conservative character of construction companies, advanced digital technologies do not become widely adopted in the short term, while vendors make determined efforts to overcome this and disseminate their technologies. This paper presents the methods of an investigation addressing the extremely complex issues related to the current practices of digital technology adoption in construction. It discusses how construction companies follow a specific logical process linked to need, project objectives, characteristics of the adopting organization, and the characteristics of the new technology to be adopted. The study aims to demonstrate a novel method of data collection and analysis including data and methodological triangulation techniques including the use of NVivo and AHP to explore how companies make the decision to uptake a new technology (e.g. advanced crane, tunnel boring machine or drones) by focusing on customer and vendor activities, their interactions, contributing factors, and people involved in the process. The major original contribution of this paper is to develop an innovative methodological Cube for investigating the Construction Technology Adoption Process (CTAP) covering technology adoption, acceptance, diffusion and implementation concepts. CTAP is a framework that delineates the phases of the process that customer organizations use when deciding to adopt a new digital technology and the parallel vendor activities. The significance of these contributions is that they enable vendors to understand how to match their strategies with customer expectations in each phase of the CTAP. It also provides a benchmark for new construction companies to use the current best practice of decision making. Future research is warranted to more clearly delineate any differences with developing nations or related industries such as mining and property management.

The Grand Ethiopian Renaissance Dam (GERD), formerly known as the Millennium Dam, is currently under construction and has been filling at a fast rate without sufficient known analysis on possible impacts on the body of the structure. The filling of GERD not only has an impact on the Blue Nile Basin hydrology, water storages and flow but also pose massive risks in case of collapse. Rosaries Dam located in Sudan at only 116 km downstream of GERD, along with the 20 million Sudanese benefiting from that dam, would be seriously threatened in case of the collapse of GERD. In this study, through the analysis of Sentinal-1 satellite imagery we show concerning deformation patterns associated with different sections of the GERD’s Main Dam (structure RCC Dam type) and the Saddle Dam (Embankment Dam type). We processed 109 descending mode scenes from Sentinel-1 SAR imagery, from December 2016 to July 2021, using the Differential Synthetic Aperture Radar Interferometry technique to demonstrate the deformation trends of both - the GERD’s Main and Saddle Dams. The time-series generated from the analysis clearly indicates different displacement trends at various sections of the GERD as well as the Saddle Dam. Results of the multi temporal data analysis on and around the project area show inconsistent subsidence at the extremities of the GERD Main Dam, especially the west side of the dam where we recorded varying displacements in the range of 10 mm to 90 mm at the crest of the dam. We conducted the current analysis after masking the images with a coherence value of 0.9 and hence, the subsequent results are extremely reliable and accurate. Further decomposition of the subsiding rate has revealed higher vertical displacement over the west side of the GERD’s Main Dam as compared to the east side. The local geological structures consisting of weak zones under the GERD’s accompanying Saddle Dam adds further instability to its structure. We identified seven critical nodes on the Saddle Dam that match the tectonic faults lying underneath it, and which display a varying degree of vertical displacements. In fact, the nodes located next to each other displayed varying displacement trends: one or more nodes displayed subsidence since 2017 while the other node in the same section displayed uplift. The geological weak zones underneath and the weight of the Saddle Dam itself may somewhat explain this inconsistency and the non-uniform vertical displacements. For the most affected cells, we observed a total displacement value of ~90 mm during the whole study period (~20 mm/year) for the Main Dam while the value of the total displacement for the Saddle dam is ~380 mm during the same period (~85 mm/year). Analysis through CoastSat tool also suggested a non-uniformity in trends of surface water-edge at the two extremities of the Main Dam.

Objective: To use the ancient and modern medical record cloud platform (V2.3.5) to organize and explore the medication patterns of the "Three Causes, Extremity, and One Disease Syndrome Formula" by Chen Wuxuan, and to summarize its therapeutic ideas. Method: Collect and organize the "San Yin Si Tian Fang" in the "San Yin Ji Yi Zheng Fang Lun", and use the modern medical record cloud platform (V2.3.5) to conduct medication frequency statistical analysis, cluster analysis, and complex network analysis. As a result, a total of 16 Chinese herbal medicines were collected in the "Three Causes, Extreme and One Disease Syndrome Formula", involving 75 traditional Chinese medicines. Statistical analysis showed that roasted licorice was the most commonly used, followed by Pinellia ternata, papaya, ginger, and Poria cocos; Medications mainly include warm drugs, sweet and pungent flavors, as well as drugs that promote lung and spleen meridians. Cluster analysis can divide the above-mentioned traditional Chinese medicine into two groups, with specific grouping as follows. Group 1: ginger, white peony, aconite, papaya, and achyranthes bidentata; Group 2: roasted licorice, poria cocos, dried ginger, pinellia ternata, and green peel. Conclusion: The characteristics of the 16 prescriptions are biased towards Xin Gan Wen, emphasizing the regulation of the spleen and stomach, which may be related to the common use of prescription by doctors in the Song Dynasty and the tendency towards warm and dry medication.

Abstract: The establishment of a circular economy in the mining sector, taking advantage of innovations in the exploration and development of hydrocarbon reserves, [ ], their [ ], transportation [ ] and subsequent processing [ ] are significant concerns. The issues surrounding the employment of technology targeted at enhancing environmental safety to increase the productivity of the reproduction process of the natural gas and oil resource base are equally important. The paper discusses the use of green seismic technology of survey to determine the oil and gas potential of the subsoil. A methodological toolkit is proposed for carrying out technical and economic calculations to determine indicators of the environmental and economic efficiency of using innovative resource-saving technology for geological survey in areas densely planted with forests. The purpose of the work is to establish the viability of employing resource-saving technology known as Green Seismic to search for promising hydrocarbon objects in forested areas and determine the expected environmental and economic benefits of geological exploration using the suggested enhanced methodology for their evaluation. The tasks set to achieve the goal were solved using methods of geological and economic assessment of the hydrocarbon raw material potential of territories and water areas, environmental assessment of the negative influence of anthropogenic environmental impact on the natural environment, economic and statistical methods of performing technical and economic calculations to determine performance indicators for the implementation of innovative projects in the field of geological exploration. The novelty of the results obtained lies in the proposed improved algorithm for conducting an environmental and economic assessment of geological exploration for hydrocarbon raw materials, a conceptual description of the Green Seismic technology, systematization of technical, economic, and environmental risks, justification of new regional directions for geological exploration using resource-saving seismic exploration technology.

Telerehabilitation is an appealing service delivery option for optimising recovering. Internationally, the equity of telerehabilitation services for people from culturally and linguistically diverse (CALD) backgrounds has been questioned. Using a 31-item survey, our study explored the access, readiness, and willingness of 260 patients to use allied health telerehabilitation services for adults receiving interventions from a large tertiary health service located in Sydney, Australia. Overall, 72% patients reported having access to technology, 38% met our readiness criteria, and 53% reported willingness to engage in telerehabilitation. There were no difference in access, readiness and willingness to engage in telerehabilitation between patients from CALD and non-CALD backgrounds. Age was the only factor that influenced access, readiness and willingness to engage in telerehabilitation. Past experience of telerehabilitation was related to willingness, but not access or readiness. Findings highlight the importance of ensuring positive patient experiences to promote ongoing willingness to use telerehabilitation. Efforts are needed to improve patients’ digital health literacy, especially patients from older age groups, to ensure equitable access to telerehabilitation services.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

Viral co-infections, where a host is infected by multiple viruses simultaneously, are common in the human population. Human viral co-infections can lead to complex interactions between viruses and the host immune system, affecting the clinical outcome and posing challenges for treatment. Understanding the types, mechanisms, impacts, and identification methods of human viral co-infections is crucial for the prevention and control of viral diseases. In this review, we first introduce the significance of studying human viral co-infections and summarize the current research progress and gaps in this field. We then classify human viral co-infections into four types based on the pathogenic properties and species of the viruses involved. Next, we discuss the molecular mechanisms of viral co-infections, focusing on virus-virus interactions, host immune responses, and clinical manifestations. We also summarize the experimental and computational methods for identifying viral co-infections, emphasizing the latest advances in high-throughput sequencing and bioinformatics approaches. Finally, we highlight the challenges and future directions in human viral co-infection research, aiming to provide new insights and strategies for the prevention, control, diagnosis, and treatment of viral diseases. This review provides a comprehensive overview of the current knowledge and future perspectives on human viral co-infections, and underscores the need for interdisciplinary collaborations to address this complex and important topic.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.