Alkali Silica Reaction (ASR) is known to be a serious problem for concrete worldwide, especially in high humidity and high temperature regions. ASR is a slow process that develops over years to decades and it is influenced by changes in environmental and loading conditions of the structure. The problem becomes even more complicated if one recognizes that other phenomena like creep and shrinkage are coupled with ASR. This results in synergistic mechanisms that can not be easily understood without a comprehensive computational model. In this paper, coupling between creep, shrinkage and ASR is modeled within the Lattice Discrete Particle Model (LDPM) framework. In order to achieve this, a multi-physics formulation is used to compute the evolution of temperature, humidity, cement hydration, and ASR in both space and time, which is then used within physics-based formulations of cracking, creep and shrinkage. The overall model is calibrated and validated on the basis of experimental data available in the literature. Results show that even during free expansions (zero macroscopic stress), a significant degree of coupling exists because ASR induced expansions are relaxed by meso-scale creep driven by self-equilibriated stresses at the meso-scale. This explains and highlights the importance of considering ASR and other time dependent aging and deterioration phenomena at an appropriate length scale in coupled modeling approaches.

Benign design of alkali-activated slag/FA geopolymer paste has intriguing increasing attention for optimizing its service performance. Therefore, the replacement of fly ash (FA) with 10 wt% silica fume (SF) is investigated by mechanical strength after freeze-thawing cycles and microstructure characterization. The results show that an appropriate dosage (30 wt%) of slag is necessary to attain alkali-activated slag/FA geopolymer paste with excellent mechanical performance, and the SF/slag/FA (SF: slag: FA= 10:30:60, wt%) geopolymer paste exerts the compressive and flexural strength of 95.2 and 3.2 MPa, respectively. Meanwhile, the doped 10 wt% SF facilitates the propagation of (N, C)-A–S–H chains, rather than the formation of C-S-H gels, evidenced by the absent exothermic peak at about 861oC from the differential scanning calorimetry (DSC) curves, leading to the increases in the pores volume with a pore diameter<20 nm and tortuosity by mercury intrusion porosimeter (MIP) results, corresponding to an improved freezing-thawing resistance with the residual compressive strength of 52.8 MPa and the weight loss of 10.5% after 300 freeze-thawing cycles. It explores a cost-effective and benign facile approach to designing heating curing-free alkali-activated slag/FA geopolymer paste with good freezing-thawing resistance.

The fireproof design of geopolymer has intriguing increasing attention by adjusting multi-component metallurgical solid wastes, due to its low-carbon emission, cost-effectiveness, and environmental conservation. Herein, the effects of silica fume (SF) on the microstructure and mechanical properties of alkali-activated slag/FA (fly ash) pastes subjected to elevated temperatures (150, 500, 850, and 1200℃) are investigated, to clarify the fact that whether or not the SF generates positive roles in mechanical strength of slag/FA (slag: FA=30:70, wt.%) geopolymers during building fires. The results show that the replacement of FA with 10 wt% SF (silica fume) promotes the increasing pore volume with a diameter of 0.2~3 μm, leading to an increase in the compressive or flexural strength below 850℃, “right shifts” of the endothermic peak, appearing uniform and compact fracture surfaces. Meanwhile, the gehlenite and labradorite generate after exposure above 850℃. While the bloating effect of the SF-containing sample occurs at 1200℃, leading to a greater deformation, due to the further restructuring of the amorphous geopolymer chain N-A-S-H or N-(Ca)-A-S-H composed from the [SiO4]4− and [AlO4]5−. It explores an effective approach for improving geopolymer’s fireproof performance by adjusting the solid-waste formulation.

Recycling of metallurgical solid waste has intriguing increasing attention for fabricating cementitious materials, due to its low-carbon emission, cost-effectiveness, and environmental conservation. Herein, the effects of silica fume (SF) on the microstructure and mechanical properties of alkali-activated slag/FA (fly ash) pastes subjected to elevated temperatures (150, 500, 850, and 1200℃) are investigated, to clarify the fact that whether or not the SF generates positive roles in mechanical properties of slag/FA geopolymers. The results show that the replacement with 10 wt% SF (silica fume) promotes the increasing pore volume with a diameter of 0.2~3 μm at room temperature, leading to an increase in the compressive or flexural strength, “right shifts” of endothermic peak and the initial-final temperature of mass loss, presenting a denser and compact fracture surface. Meanwhile, the mineral phase of gehlenite and labradorite emerges after exposure above 850℃ from the XRD results. Furthermore, the bloating effect of the incorporated SF occurs due to the formation of a liquid phase altogether with the amorphous silicates after exposure to 1200℃, leading to a greater deformation and enhancement of restructuring involved in the [SiO4]4− and [AlO4]5−. It explores an effective recycling approach for fabricating paste binders using metallurgical solid wastes.

This article deals with the possibility of partial replacement of blast furnace slag with fly ash after denitrification by the Selective Non-Catalytic Reduction (SNCR) method in alkali-activated materials. In the experiment, the basic physical-mechanical properties and durability properties were tested, the hydration reaction was monitored in a calorimeter and infrared spectroscopy was performed. Results were compared between mixtures prepared with fly ash without denitrification and also with reference mixture based only on alkali-activated blast furnace slag. The basic result is the finding, that hybrid alkali-systems with fly ash after denitrification show similar trends as hybrid alkali-systems with fly ash without denitrification. The significant effect of fly ash is manifested especially in terms of resistance to freeze-thaw. The reactions in the calorimeter show a slower development of reactions with increasing replacement of slag by fly ash. In the case of testing resistance to leaching in demineralised water, a decrease of flexural strength was found, which corresponds to the conclusions of strength testing, that long-term deposition of bodies in water causes deterioration of mechanical properties.

The present work aims to explain the aluminum hydrolysis reaction kinetics based on properly chosen theoretical model with machined aluminum waste chips and alkali solutions up to 1M as a promoter, and to estimate overall reaction profit. In order to obtain results of better accuracy, we work with flat Al waste chips because a flat surface is preferable to maximally increase the time for created hydrogen bubbles to reach the critical gas pressure. At describing the reaction kinetics, flat shape allows using a planar one-dimensional shrinking core model instead of much complicated polydisperse spheric shrinking core model. We analyze the surface chemical reaction and mass transfer rate steps to obtain the first order rate constant for surface reaction and the diffusion coefficient of aqueous reactant in the byproduct layer, respectively. With our reactor we achieved H2 yield of 1145 mL per 1 g Al with 1M NaOH, which is 92% of the theoretical maximum. At estimation of the profit, we pay much attention to the loss of alkaline and find a crucial dependence on its price. Nevertheless, in terms of consumed and originated materials for sale, conversion of the aluminum waste material into green hydrogen by properly chosen reaction parameters has a positive profit even by consuming alkali of chemical grade.

Alkali-activated materials are alternative building binders, where secondary raw materials are processed. Possibility to use landfilled waste materials in their preparation, increases their potential application in construction practice, and therefore they are subject to extensive research, especially in recent years. This paper briefly summarizes interesting results of an experiment aimed at verifying the possibility of applying cement by-pass dust (CBPD) in the preparation of alkali-activated materials. The research work was focused on the possibilities of using these wastes for the preparation of small elements of garden architecture. The paper briefly evaluates in particular the results of X-ray diffraction, which were subjected to three types of binder pastes differing in the amount of used activator. In the experiment, a mixture of blast furnace granulated slag, fly ash and cement by-pass dust was alkali activated with sodium metasilicate.

This study is focused on the experimental investigation of compressive strength and durability properties of lightweight concrete mixtures with fine expanded glass and expanded clay aggregates using different microfillers. The paper proposes the relationships between the compressive strength and density of concrete mixtures with different proportions of lightweight aggregates mentioned above. The performed experimental studies have revealed the tendencies of possible usage of different amount of fine lightweight aggregates and their combinations in the production of concrete mixtures depending on the demands of practical application. Following the requirements for structural concrete subjected to environmental effects, durability properties (alkaline corrosion and freeze–thaw resistance) of the selected concrete mixtures with expanded glass aggregate were studied. The results of the experimental investigations have shown that durability of tested concrete specimens was sufficient. The study has concluded that the mixtures under consideration can be applied for the production of structural elements to which durability requirements are significant.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Concrete is the most commonly used construction material due to its various advantages, such as versatility, familiarity, strength and durability and it will continue to be in demand far into the future. However, with today’s sensitivity to the environmental protection, this material is facing unprecedented challenges due to its high greenhouse gas emission mainly during cement production. This paper investigates one of the promising cement replacement materials, alkali activated cement (AAC) concrete. Being produced mainly from byproduct materials and having a comparable structural performance to conventional concrete, AAC concrete has a potential to transform the construction industry. Mechanical properties such as compressive and flexural strength and the relationship between them are studied. Different source materials such as fly ash (FA), ground granulated blast furnace slag (GGBS), silica fume (SF) and Metakaolin (MK) are used. The effect of the source materials and the activator solutions on the concrete performance is studied. Furthermore, the freeze-thaw resistance of the concrete is studied. The results of the study showed that the behavior of AAC depends highly on the source material combinations as well as type used. The effect of the alkaline solution is also dependent on the source material used. Mixes with higher GGBS content in general showed the highest strength while mixes with MK showed the highest flexural strength. The results from the freeze-thaw test showed that proper design of AAC concrete with a lower water content is critical to achieve a good resistance.

In the study, ground granulated blast furnace slag was activated with a wide variety of sodium salts to compare the effect of their pH and anion size on the hydration progress and compressive strength development of GGBFS pastes. Research was carried out on samples activated with twelve different sodium salts, cured for one year. Changes in their phase composition (XRD), loss on ignition at different temperatures, expansion and microstructure (SEM+EDS) were examined over the entire curing period. Studies have shown that the presence of sodium ions is more important than the pH of the system, as activation took place even in the case of compounds whose solutions are characterized by low pH, such as sodium tartrate or phosphate. The compressive strength of the pastes ranged from approximately 8 to 65 MPa after one year of curing.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Chemical flooding is one of the effective methods to recover large volumes of oil from sandstone formations after primary depletion. However, silica dissolution often occurs during Alkaline-Surfactant-Polymer (ASP) flooding, affecting the petro-physical properties of the formation. To address this issue, samples from Berea sandstone formations were treated with various brine solutions, through static tube tests and core flooding experiments. Analytical tests such as DR/2800 spectrophotometer and scanning electron microscope were used to evaluate the silica solubility and the alteration in mineral content. The results indicated that the silicate contents decreased after the saturation due to silica solubility in the solution. Increasing brine salinity to 40,000ppm and introducing Magnesium and Calcium ions to the solution, reduces the silicate contents by 5.03 % and 7.32 %. Moreover, saturating the samples with ASP solution, further reduced the silicate contents by 14.86 %. This reduction is associated with a relative increase in silica solubility and pH of the solution. Silica dissolution affects the pore microstructure, which resulted in increasing the porosity and pore volume after the core flooding. The injection of the ASP solution increased the porosity by 5.83%, thus the pore volume increased from 17.72 to 18.76cc. This is associated with the high silica solubility and the increase of solution pH in the ASP solution. The permeability of the samples generally reduced after the core flooding, due to the silica solubility. However, injecting the ASP solution, resulted in a major reduction of the permeability by more than 75%. These changes in the petro-physical properties can lead to severe formation damage, and affect hydrocarbon production. This study assists in understanding the impact of silica dissolution during ASP treatment and addresses the factors involved. Efficient utilization of chemical flooding can help mitigating silicate scaling within the formation, and extend field productivity.

Fish oil rich in docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA), vitamin D₃ and natural astaxanthin sustainably extracted from anchovy fillet leftovers using biobased limonene only, can be conveniently stabilized by adsorption on periodic mesoporous silicas. The simplicity of the process, the high load of entrapped fish oil, and the biocompatible nature of silica support numerous forthcoming applications of this new class of “Omeg@Silica” materials.

The recycling of common soda-lime glass (SLG) is far from being complete, since the material may contain small polymeric, metallic and ceramic contaminations. This has a negative impact on the quality of new glass articles prepared via re-melting. Alternatively, the full reuse of contaminated cullets could be achieved by low-temperature consolidation into geopolymer-like materials. SLG powders, used either as received or pre-washed in acid solution, were added to a sodium aluminate solution at the room temperature for 3 h, under low-speed mechanical stirring. Microporous semi-crystalline monoliths were formed by the casting of suspensions in plastic molds and cured at 75°C overnight. The monoliths featured hydrosodalite as the main crystalline phase for as received SLG and LTA zeolite in the case of pre-washed SLG. The mechanical properties compared well with those of cementitious materials. Moreover, by addition of coarse glass particles as fillers, the methodology successfully yielded Venetian terrazzo-like samples, which could lead to significant material and energy savings in their manufacture. The proposed approach could also be extended to other difficult-to-reuse glass formulations and provide attractive and versatile up-cycled materials.

As the major greenhouse gas, CO2 gas emission has been noticeably increased over the past decades resulting in global warming and climate change. As a result, it is imperative to reduce the excess CO2 in the atmosphere to hold “the increase in the global average temperature to well below 2°C (ideally 1.5°C) above pre-industrial levels set by the Paris Agreement on climate change. Among many ways, CO2 capture technology is considered as the most promising technology among the available technologies. Porous materials such as carbons, silica, zeolites, hollow fibers, and alumina are widely used as CO2 sorbents. However, among the available porous sloid sorbents, porous silica-based materials grabbed a significant attention due to their unique properties including high surface area, pore volume, good thermal and mechanical stability, and low cost. Therefore, development of porous silica materials as a promising CO2 absorbent is a continuously expanding research area in the current moment. Herein, we aim to visualize a full picture of the porous silica-based materials for CO2 capture. This review presents a comprehensive study of existing CO2 capture techniques and highlights the recent progress of different porous silica materials and synthesis processes. CO2 adsorption capacities of unmodified porous silica materials are less effective as compared with functionalized silica materials. Various research activities have been reported about functionalization of pours silica using amine groups. Therefore, in this review, different synthesis routes of amine-functionalized porous silica materials, CO2 adsorption capacities, gas selectivity and reusability were discussed. Moreover, the research challenges associated with the porous silica materials and future research directions are summarized.

It remains unclear in the literature what is the cause of the so-called alkali-carbonate reaction (ACR) damage to concrete yet, a consensus is reached when considering dedolimitization as non-expansive. However, expansion and cracks as distress features are often attributed to alkali-silica reaction (ASR) when evidence of a reactive mineral is found in the aggregate. Evidently, different types of aggregates may produce different types and degrees of damage. Therefore, this work aims to assess the damage to concrete generated and propagated by the so-called ACR susceptible reactive Kingston coarse aggregate through mechanical testing (i.e., direct shear test), microscopy (the damage rating index – DRI), and other techniques. Distinct induced expansion levels (i.e., 0%, 0.05%, 0.12%, and 0.20%) were selected to compare the distress caused by ACR to concrete affected by ASR. Result show that the behaviour of ACR, namely as captured through the DRI, is inconsistent with that of ASR thus attesting to ACR being a distinct distress mechanism.

The composites of heteropolyacids (H3PW12, H3PMo12) incorporated into amine-functionalized silica materials, were used for the first time as heterogeneous catalysts in the valorisation of glycerol (a large waste from biodiesel industry) by acetalization reaction with acetone. The polyoxotungstate catalyst H3PW12@AptesSBA-15 presented higher catalytic efficiency than the phosphomolybdate, with 97% of conversion with 97% of solketal selectivity, after 60 min at 25 °C, or 91% of glycerol conversion and the same selectivity, after 5 min, performing the reaction at 60 ºC. A relation of catalytic performance and acidity of the catalyst is here presented. Furthermore, the stability of the solid catalyst was investigated and discussed.

Mineral surfaces have been demonstrated to play a central role in prebiotic reaction, which are supposed to be at the basis of the origin of life. Among the various molecules proposed as precursors for these reactions, one of the most interesting is formamide. Formamide has been shown to be a pluripotent molecule, generating a wide distribution of relevant pre-biotic products. In particular, the outcomes of its reactivity are strongly related to the presence of mineral phases, acting as catalysts toward specific reaction pathways. Even if the mineral-products relationship has been deeply studied for a large pool of materials, the fundamental description of the formamide reactivity over the mineral surface at a microscopic level is missing in the literature. In particular, a key step of formamide chemistry at surfaces is its adsorption on the available interaction sites. This report aims to investigate the adsorption of formamide over a well-defined amorphous silica, chosen as model mineral surface. An experimental IR investigation of formamide adsorption has been carried out and its outcomes have been interpreted on the basis of first principles simulation of the process adopting a realistic model of the amorphous silica.

Nowadays, the study of preparing silica/rubber composites, which can be used in “green tire”, in energy saving method is fast-growing. In our work, silica modified by using alcohol polyoxyethylene ether (AEO) and 3-Mercaptopropyltriethoxysilane (K-MEPTS) together were investigated. Thermal gravimetric analyzer (TGA) result indicated that both AEO and K-MEPTS could be grafted on the silica surface. Raman spectroscopy confirmed that the AEO could generate a certain steric hindrance for the mercaptopropyl group on K-MEPTS. Silica modified by using AEO and K-MEPTS together can be completely co-coagulated with the rubber in preparing silica/natural rubber (NR) composites by latex compounding method. AEO can form a physical interface between silica and rubber; meanwhile, K-MEPTS can form a chemical interface between silica and rubber. The effects of chemical and physical interface between silica and rubber on dynamic and mechanical performances of silica/NR composites were also given in this research. A proper combination of physical and chemical interface between silica and NR can improve performances of silica/NR composites.

An attempt to investigate the effect of binary composite activators on the microstructure of fly ash-based geopolymers is conducted through the comparison of 24 experiments, which consisted of Na2SiO3•9H2O, Na2CO3, K2CO3, NaOH, and KOH through a facile preparation technique. The results show that the activator of Na2SiO3•9H2O+KOH presents the highest mechanical strength, due to the synergy activation between the inherent ≡Si-O-Si≡ chains derived from Na2SiO3 and K+’s catalysis. It reveals that the K+ plays a crucial role in Na2SiO3-activated fly ash geopolymer, which is the rate-determining step of the enhanced crosslinking and propagation of N-(C)-A-S-H chains, leading to an increase in weight loss temperatures of specimens from TG/DTG results. Furthermore, the adding silica fume facilitates as-formed amorphous silicates, which also could fill into the pores of N-(C)-A-S-H amorphous gels and present a uniform and compact morphology, leading to an increase in the pore volume of the pore diameter less than 100 nm. It explores an efficient and cost-effective preparation of fly ash-based geopolymer for developing solid-waste recycling techniques.

Steel slag is a co-product of the steelmaking industry, this material is rarely used as a binder due to its low cementitious properties. Thus, it´s believed that the alkaline activation of steel slag can enable its use as a cementitious material. This work has the objective of making a systematic bibliographic review on the theme "slag melt as a precursor in activated alkali binders". To this end, the ProKnow-C method was used for the selection and analysis of relevant research on the topic. The portfolio resulted in 71 texts, mostly journals paper. Bibliometrics showed that the country with the most publications is China and the journal with the most publications is Construction and Building Materials. The critical analysis concluded that the XRD, XRF, and compressive strength tests are the most used for the characterization of the material. It is possible to establish that there are some knowledge gaps on the subject, such as better mechanical characterization and greater production of works with dosing by the one-part method.

Mitigation of Anthropogenic CO2 emissions possess a major global challenge for modern societies. Herein catalytic solutions are meant to play a key role. Among the different catalysts for CO2 conversion Cu supported on molybdenum carbide is receiving increasing attention. Hence, in the present communication we show the activity, selectivity and stability of fresh-prepared -Mo2C catalysts and compare the results with those of Cu/Mo2C, Cs/Mo2C and Cu/Cs/Mo2C in CO2 hydrogenation reactions. The results showed that all the catalysts were active and the main reaction product was methanol. The results showed that copper-cesium and molybdenum effectively interact and that cesium promoted the formation of metallic Mo. While, the incorporation of copper is positive to improve the activity and selectivity to methanol, the presence of Mo0 phase was detrimental for the conversion and selectivity. Moreover, the catalysts promoted by cesium underwent redox surface transformations during the reaction that diminished their catalytic performance. The molybdenum phase in Cu/Mo2C changes during reaction leading to metallic molybdenum and tuning the catalytic activity.

Elevated antimony concentrations in aqueous environments from anthropogenic sources is becoming of global concern, here iron oxides are known to strongly adsorb aqueous antimony species with different oxidation states, but the effect of silica on the removal characteristics is not well understood despite being a common component in the environment. In this study, ferrihydrite was synthesized at various Si/Fe molar ratios to investigate its adsorption and co-precipitation behaviors with aqueous antimony anionic species, Sb(III) and Sb(V). The XRD analyses of the precipitates showed two broad diffraction features at approximately 35° and 62° 2θ, which are characteristic of 2-line ferrihydrite, no significant shifts in peak positions in the ferrihydrite regardless of the Si/Fe ratios. The infrared spectra showed a sharp band at ~990 cm⁻¹, corresponding to asymmetric stretching vibrations of Si-O-Fe bonds which increased in intensity with increasing Si/Fe molar ratios. Further, the surface charge on the precipitates became more negative with increasing Si/Fe molar ratios. The adsorption experiments indicated that Sb(V) was preferentially adsorbed at acidic conditions and decreased dramatically with increasing pH while the adsorption rate of Sb(III) ions was independent of pH, however, the presence of silica suppressed the adsorption of both Sb(III) and Sb(V) ions. The results showed that Sb(III) and Sb(V) ions were significantly inhibited by co-precipitation with ferrihydrite even in the presence of silica by isomorphous substitution in the ferrihydrite crystal structure.

Antimicrobial peptides (AMPs) have emerged as a promising solution to tackle bacterial infections and combat antibiotic resistance. However, their clinical application has been hindered by their vulnerability to protease degradation and toxicity towards mammalian cells. To overcome these challenges, our study aims to develop a method to enhance the stability and safety of AMPs, applicable to effective drug-device combination products. KR12 antimicrobial peptide was chosen and in order to further enhance its delivery and efficacy, HIV TAT protein-derived cell-penetrating peptide (CPP) was fused to form CPP-KR12. A new product, CPP-KR12@Si, was developed by forming silica nanoparticles with self-entrapped CPP-KR12 peptide using the biomimetic silica precipitability due to its cationic nature. Peptide delivery from CPP-KR12@Si to bacteria and cells was delivered at a slightly delayed rate with improved stability against trypsin treatment and a reduction in cytotoxicity over CPP-KR12. Finally, the antimicrobial potential of CPP-KR12@Si/bone graft substitute (BGS) combination product was demonstrated, which is coated with CPP-KR12 in the form of nanoparticles on the surface of BGS. Self-entrapped AMP in silica nanoparticles is a safe and effective AMP delivery method that will be useful for developing a drug/device combination product for tissue regeneration.

Alkali-activated materials, sometimes called geopolymers, can be used as alternative cementitious materials to conventional Portland cement. There is a significant current interest in these materials due to their low CO2 footprint. Typical applications of alkali-activated materials are within civil engineering, however, potential applications as well cementing material within oil & gas are also being studied with emerging interest. This paper presents a systematic study of compressive strength development from 1 to 28 days for metakaolin-based alkali-activated cement. The results show that compressive strength is highly dependent upon the initial Si/Al ratio in the mix design, as well as the concentration of the activator solution. Furthermore, due to the relatively low initial reactivity of the used metakaolin material, different types of co-binders were included in the slurry composition to improve early strength development. The two different co-binders tested were another, more reactive metakaolin material and Blast Furnace Slag (GGBFS). It was found that both these co-binders performed as intended, by ensuring early strength development via precipitation of K-A-S-H and C-A-S-H gels, respectively, and also by enabling subsequent strength development due to improved dissolution of the low-reactive metakaolin.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

Lewis acid zeolites play an important role in industrially important green reactions closely related to fine chemicals and biomass conversion. Titanium-doped TS-1 zeolite is a milestone Lewis acid zeolite, which widely uses in industrially significant green oxidation processes with hydrogen peroxide as an oxidant under mild conditions. TS-1 Zeolites are normally synthesized in basic condition under hydrothermal treatment. Up to now, it is still not successful to synthesize active TS-1 Lewis acid zeolite by using inorganic alkali, e.g. NaOH or KOH as base, which are cheaper and more stable compared with quaternary ammonium hydroxide or organic amines used in the traditional synthesis. Here, inorganic base of NaOH was firstly employed in synthesizing active TS-1 zeolites. The crucial factor was the control of adverse effects of sodium cations on the incorporation of active titanium cations. A higher catalytic activity could be achieved by further reducing the size of the TS-1 crystal by seed-added strategy, which could approach the catalytic activity of commercial catalyst while the production cost was much lower than the commercial TS-1 catalysts, indicating great commercial potential and the possibility of preparing other cheap Lewis acid catalysts by using inorganic alkali.

In this work, a novel silane coupled cationic precursor (SAGS) was synthesized by 3-glycidyloxypropyltrimethoxysilane and sodium 2-((2-aminorthyl)amino) ethanesulfonate. A series of cation exchange membranes were prepared with poly(vinyl alcohol) (PVA) and SAGS by sol-gel process. The structure of the prepared membranes were characterized by fourier transform infrared spectrum (FTIR) and scanning electron microscopy (SEM), and its properties were studied by water uptake (WR), cation exchange capacity (CEC), linear expansion ratio (LER), alkali stability, thermogravimetric analysis (TGA), mechanical properties and diffusion dialysis performance. FTIR and X-ray photoelectron spectroscopy (XPS）confirmed the successful preparation of SAGS membranes, and SEM images showed that the prepared membranes were dense and uniform. The WR values of the SAGS membranes were in the range of 91.49-122.39 %, and the LER values were 17.65-28.21 %. In addition, the SAGS membranes had suitable CEC value, good alkali resistance and thermal stability which ensured the application of membranes in the field of diffusion dialysis (DD) for alkali recovery. In DD test, the dialysis coefficients of NaOH (UOH) ranged from 0.012 mm/h to 0.023 mm/h, and the separation factors (S) was in the range of 30.77-16.43. In summary, the prepared membrane had good performance and simple preparation process, which had great application potential in textile industrial wastewater recovery.

Single-particle inductively coupled plasma mass spectrometry (spICP-MS) has been used for particle size measurement of diverse types of individual nanoparticles and micrometer-sized carbon-based particles, such as microplastics. However, its applicability to the measurement of micrometer-sized non-carbon-based particles such as silica (SiO2) is unclear. In this study, the applicability of spICP-MS to particle size measurement of non-porous/mesoporous SiO2 micro-spheres with a nominal diameter of 5.0 µm or smaller was investigated. Particle sizes of these microspheres were measured using both spICP-MS based on a conventional calibration approach using an ion standard solution and scanning electron microscopy (SEM) as a reference technique and the results were compared. The particle size distributions obtained using both techniques were in agreement within analytical uncertainty. The applicability of this technique to the detection of metal-containing protein-binding mesoporous SiO2 microspheres was also investigated. Bound iron (Fe)-containing proteins (i.e., lactoferrin and transferrin) of mesoporous SiO2 microspheres were detected using Fe as a presence marker for the proteins. Thus, spICP-MS is applicable to the particle size measurement of large-sized and non-porous/mesoporous SiO2 microspheres; it has considerable potential for element-based detection and qualification of bound proteins of mes-oporous SiO2 microspheres in a variety of applications.

This study reports the preparation of silica and nano-fructosome encapsulated Candida antarctica lipase B particles (CalB@NF@SiO2) and demonstration of their enzymatic hydrolysis and acylation. CalB@NF@SiO2 particles were prepared as a function of TEOS concentration (3-100 mM). Their mean particle size was 185 nm by TEM. Enzymatic hydrolysis was performed to compare catalytic efficiencies of CalB@NF and CalB@NF@SiO2. Catalytic constants (Km, Vmax, and Kcat) of CalB@NF and CalB@NF@SiO2 were calculated with Michaelis-Menten equation and Line-weaver Burk plot. Optimal stability of CalB@NF@SiO2 was found at pH 8 and temperature of 35 ℃. Moreover, CalB@NF@SiO2 particles were reused for seven cycles to evaluate their reusability. In addition, enzymatic synthesis of benzyl benzoate was demonstrated by an acylation reaction with benzoic anhydride. The efficiency of CalB@NF@SiO2 for converting benzoic anhydride to benzyl benzoate by the acylation reaction was 97%, indicating that benzoic anhydride was almost completely converted to benzyl benzoate. Consequently, CalB@NF@SiO2 particles are better than CalB@NF particles for enzymatic synthesis. In addition, they are reusable with high stability at optimal pH and temperature.

Major progress in the field of regenerative medicine are expected from the design of artificial scaffolds that mimic both the structural and functional properties of the ECM. The bionanocomposites approach is particularly well fitted to meet this challenge as it can combine ECM-based matrices and colloidal carriers of biological cues that regulate cell behavior. Here we have prepared bionanocomposites under high magnetic field from Tilapia fish scale collagen and multifunctional silica nanoparticles (SiNPs). We show that scaffolding cues (collagen), multiple display of signaling peptides (SiNPs) and control over the global structuration (magnetic field) can be combined into a unique bionanocomposite for the engineering of biomaterials with improved cell performances.

Heavy metals are non-biodegradable and have a high toxicity effect to living things which makes their presence in the environment extremely dangerous. The method of handling heavy metals waste by photocatalysis techniques using TiO2/SiO2 composite showed a good performance in reducing harmful pollutants. In this study, SiO2 from Bengkulu beach sand was used as a support material for TiO2 photocatalyst to reduce Cr(VI) and Pb(II) concentrations. SiO2 was obtained through leaching techniques using NaOH as a solvent. The TiO2/SiO2 composite photocatalyst were synthesized using a solvothermal method at 130 °C and then characterized using XRD, FTIR, SEM and PSA. Based on the XRD diffractogram, the synthesized TiO2 showed the anatase structure while the SiO2 showed the amorphous structure. Ti-O-Si bond is defined in the IR spectra, which indicates that the relationship between TiO2 and SiO2 is a chemical interaction. The results of SEM and PSA characterizations show agglomerated spherical (round) particles with a mean particle size of 616.9 nm. The TiO2/SiO2 composite of 7:1 ratio showed the highest photocatalytic activity after 180 minutes of UV irradiation, with a concentration-decrease percentage of 93.77% and 93.55% for for Cr(VI) and Pb(II), respectively.

The present contribution is focused on the relation preparation – structure – optical properties of hybrid silica and zirconia powders containing Eu(III) complexes: [Eu(ntac)₃][pphendcn] and [Eu(phen)₂](NO₃)₃. Methods for functionalization of silica and zirconia microparticles, based on adsorption of 1,10-phenantroline and [Eu(ntac)₃][pphendcn], and doping with [Eu(phen)₂](NO₃)₃ nanoparticles are proposed to obtain of red emitting hybrid composites with quantum efficiency 20 – 50 %. The optical properties of rare earth ions incorporated in silica and zirconia composites are used to explore the site symmetry (D₂, C_2v or lower) of the Eu³⁺ optical centers in the hybrid composites. Quantum yields of the investigated sol-gel micropowders and quantification of their optical spectra are presented.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

This paper summarizes some works exploiting the ate-type addition of electron-withdrawing monomers to hydrogenosiloxane groups so as to generate new silicone materials. Two types of monomers were oligomerized onto silicone backbones, namely unsaturated phosphonate and sulfone monomers. Phosphonated silicones are thermally more resistant than conventional silicones and can be transformed into amphiphilic polymers after selective ester hydrolysis. Sulfoned silicones generate solid supramolecular elastomers thanks to the strong pseudo-ionic interactions in play between sulfone groups. Rheology and modulated DSC show a solid/viscoelastic transition around 175°C, which allows using these thermoplastic materials on a larger scale than conventional silicone urea copolymers. These results open new avenues in the generation of silicone block- and grafted-copolymers with unique functionality and properties.

The practical application of a pH-responsive Nanoparticle Drug Delivery System (NDDS) in cancer treatment is often hampered by several issues such as the protection of therapeutic molecules from external stresses, inefficient targeted delivery, sustained drug release, and poor efficacy. This study presents an effective design strategy for the synthesis of a pH-sensitive controlled hydrophobic drug delivery method based on the formulation of chitosan (CS)-coated mesoporous silica nanoparticles (MSNs) through the sol-gel method, where hydrolysis takes place in the acidic medium followed by polycondensation of the hydrolyzed products. For this purpose, NH2 modified-MSNs were prepared by using tetraethyl orthosilicate (TEOS) as precursor and cetyltrimethylammonium bromide (CTAB) as a template, and 3-aminopropyltriethoxysilane (APTES) for amine modification, followed by hydrophobic drug loading and CS coating of various concentrations. Camptothecin (CPT) was used as a model drug. Fabricated monodispersed functionalized nanoparticles had sizes ranging from 200nm to 245nm with an encapsulation efficiency as high as 90%. The highest encapsulation efficiency was found for 1% CS coating, which released 50% drug in 120h at pH 6.4 and 20% at pH 7.4 respectively. These nanoformulations exhibited pH-responsive release patterns of CPT under two different pH values (pH=7.4 and pH=6.4). These results contribute to the optimization of NDDS, with potential implications for nanoformulations designed for controlled and sustained drug release particularly to tumors without affecting healthy cells owing to differences in the pH of the tumor microenvironment and the normal physiological environment of cells.

This study aims to formulate binary cementitious systems containing silica fume (SF) and micro quartz (MQ) to improve cementitious concrete's durability and mechanical properties. In this investigation, we examined the effects of different essential variables, such as the level of SF and MQ replacement and the ratio of the water-binder (w/b). In this study, the w/b ratios were 0.25, 0.3, 0.35, and 0.4. Replacement levels for SF were 8, 10, and 12%, while replacement levels for MQ were 5, 8, 10, 15, 25, and 35%. The porosity and permeability decreased with an increase in replacement levels, regardless of the type of fine material used or the amount of replacement. Meanwhile, the strength increased markedly with SF replacement, reaching its maximum MQ of 25% at the SF level. The strength of the SF mixing was the highest in all mixes, and it remained the highest until 15% of MQ was replaced. The ultrafine size of MQ particles contributes to the improvement of compressive strength, porosity, and permeability in a similar way to SF particles, despite their high crystalline structure. Furthermore, in this study, analysis of variance (ANOVA) was employed to verify the influence of each variable on the studied response.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

Nanomaterials exhibit novel properties and profound attributes as an additive in asphalt binder modification. However, the application of nano-silica in asphalt binders and mixture modification is still limited and further research is required. Along these lines, in this work, nano-silica with a content from 2% to 8% and an increment of 2% were utilized in modifying the bitumen binder type C320, which is considered the most conventional type of bitumen used in Western Australia road asphalt mixtures. Various tests were performed to assess their properties including dynamic shear rheometer, penetration, softening point, and multiple stress creep recovery (MSCR) test. The extracted results revealed an increase in the strength and stiffness properties by lowering the penetration, improving the softening point, and increasing the complex shear modulus of all nano-silica modified bitumen samples. Interestingly, a relatively big content of nano-silica leads to a higher rutting resistance. Nevertheless, the rutting resistance was affected by the size of the nano-silica coated with the silane coupling agent. The ideal sample of nano-silica modified C320 was determined as NS-15nm (NS-A), which can improve the rutting resistance. Nevertheless, the rutting resistance of the modified asphalt mixtures needs to be further investigated in the future to elaborate on the impact of nano-silica as modified binders on the mechanical properties of Australian asphalt mixtures.

Because of their low cost and easy production silica nanoparticles (NPs) are amply used in multiple manufactures as anti-caking, densifying and hydrophobic agents. However, this has increased the exposure levels of the general population and has raised concerns about possible toxicity of this nanomaterial. NPs are known to affect the function of the airway epithelium, but the biochemical pathways targeted by these particles remain largely unknown. Here we investigated the effects of NPs on the responses of cultured human bronchial epithelial (16HBE) cells to the damage-associated molecular pattern ATP, using fluorometric measurements of intracellular Ca2+ concentration. Upon stimulation with extracellular ATP these cells displayed a concentration-dependent increase in intracellular Ca2+, which was mediated by release from intracellular stores. Silica NPs inhibited the Ca2+ responses to ATP within minutes of application and at low micromolar concentrations, which are significantly faster and more potent than those previously reported for the induction of cellular toxicity and pro-inflammatory responses. NPs-induced inhibition appeared to be independent from the increase in intracellular Ca2+ they produce, and via a non-competitive mechanism. These findings suggest that NPs reduce the ability of airway epithelial cells to mount ATP-dependent protective responses such as the increase in mucociliary clearance and cough.

The article describes synthesis of aminoorgano-functionalized silica as a perspective material for catalysis application. The amino groups have electron donor properties valuable for metal chemical state of palladium. So presence of electron donor groups is important for increasing of catalysts stability. The research is devoted to investigation of silica amino-modified support influence on activity and stability of palladium species in 4-nitroaniline hydrogenation process. A series of catalysts with different supports such as SiO2, SiO2-C3H6-NH2 (amino-functionalized silica), γ-Al2O3 and activated carbon were studied. The catalytic activity was studied in the hydrogenation of 4-nitroaniline to 1,4-phenylenediamine. The catalysts were characterized by scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and pulse chemisorption of hydrogen. The 5 wt. % Pd/SiO2-C3H6-NH2 catalyst exhibited the highest catalytic activity for 4-nitroaniline hydrogenation with 100% conversion and 99% selectivity with respect to 1,4-phenylenediamine.

The studied Khanbogd pluton of peralkaline granite is located in southern Mongolia and occupies an area of ~1000 sq. km. Previously, two ring-shaped bodies were constructed in a flattened shape pluton. However, this shape was not used for the genesis of this pluton. A recent study of Landsat image showed a several elliptical intrusions in two bodies. Chemistry interpretation shows that each intrusion differs in ASI, CIPW norms, 87Sr/86Sri and δ18O isotopes. Elliptical intrusions, uplifted country rocks between them, and roof pendants suggest magma penetration along fractured country rocks. Furthermore, two adjacent intrusive bodies and undeformed host rocks at the front part of the pluton are consistent with underplating magmatic factors during duplex-type thrusting. This magma event is also supported by low of Sr, Ba, Eu and high of Th, U, Pb anomalies and a few amount of garnet crystals in the granites, implying vapor absent melt crystallization associated with underplating. Multiple melt sources, as well as from mantle and recycled sea floor rocks, are identified by ratio of 87Sr /86Sri and δ18O values. The low isotope values, the thrust nature and 295–286 Ma ages of the alkali granites, indicate an underplate magma evidenced during Permian rifting.

The Bayer process is the maim method of alumina production worldwide. The use of low-quality bauxites for alumina production results in the formation of a significant amount of technogenic waste - bauxite residue (BR). The Bayer reductive method is one possible way to eliminate BR stockpiling, but it requires high-pressure leaching at temperatures higher than 220 °C. In this research, the possibility of boehmitic bauxite atmospheric pressure leaching at both the first and second stages or high-pressure leaching at the second stage with the simultaneous reduction of hematite was investigated. Bauxite and solid residue after NaOH leaching were characterized using XRD, SEM-EDS, and Mössbauer spectroscopy methods. The first stage of leaching under atmospheric pressure with the addition of Fe(II) species in a strong alkali solution (330-400 g L–1 Na2O) results in a partial reduction of the iron minerals and an extraction of more than 60% of Si and 5-25% of Al (depending on caustic modulus of solution) after 1 h. The obtained desilicated bauxite was subjected to atmospheric leaching at 120 °C in a strong alkali solution (350 g L-1) or high-pressure leaching at 160-220 °C using the Bayer process mother liquor in order to obtain a concentrate with a magnetite content higher than 83 wt. %.

This work presents the production and incorporation of calcium hydrolyzed nano-solutions at three concentrations (1, 2, and 3 wt.%) in alkali-activated gold mine tailings (MTs) from Arequipa, Perú. A first activator solution of sodium hydroxide (NaOH) at 10M was used. The calcium hy-drolyzed nano-solutions acted as a secondary activator and as additional calcium resource for the alkali-activated materials (AAMs) based on the low-calcium gold MTs. High-resolution trans-mission electron microscopy/energy-dispersive x-ray spectroscopy (HR-TEM/EDS) analyses were carried out to characterize the morphology, size, and structures of the calcium hydrolyzed na-noparticles. Fourier transform infrared (FTIR) analyses then were used to understand the chemical bonding interactions in the calcium hydrolyzed nanoparticles and in the AAMs. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and Quantitative X-ray diffraction (QXRD) were performed to study the structural, chemical, and phase compositions of the AAMs; uniaxial compressive tests evaluated the compressive strength of the reacted AAMs; and Nitrogen adsorption-desorption analyses measured the porosity changes at nanostructure level in the AAMs. The results indicate that each increase in the concentration of the calcium hydrolyzed nano-solution had a direct/proportional effect on the mechanical properties of the AAMs samples. The AAMs with 3 wt.% calcium-hydrolyzed nano-solution had the highest compressive strength value of 15.16 MPa, which represented an increase of 62% compared to the original system without nanoparticles and aged under the same conditions of 70°C for seven days. These results provide useful information about the positive effect of calcium-hydrolyzed nanoparticles on gold MTs and their conversion into sustainable building materials through alkali activation.

This study aims to model grinding of a Polish slag and evaluate the particle size distributions of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e. temperature, curing and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin-Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multi fractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

Fused silica glass is a material with outstanding mechanical, thermal and optical properties. Being a brittle material, it is challenging to shape. In the last decade, the manufacturing of monolithic flexible mechanisms in fused silica has evolved with the femtosecond laser-assisted etching process. However, instrumenting those structures is demanding. To address this obstacle, this article proposes to inscribe a Bragg Grating sensor inside a flexure and interface it with an optical fibre to record the strain using a spectrum analyzer. The strain sensitivity of this Bragg Grating sensor is characterized at 1.2 pm/μϵ (1 μϵ = 1 microstrain). Among other applications, deformation sensing can be used to record a force. Its use as a micro-force sensor is estimated. The sensor resolution is limited by our recording equipment to 30 μN over a measurement range above 10 mN. This technology can offer opportunities for surgery applications or others where precision and stability in harsh environments are required.

In this work, alkylammonium-functionalized hollow mesoporous silica as nonocarrier of drugs was synthesized to realize enhanced cancer therapy by pH stimuli for sustained drug release. First, functionalized hollow mesoporous silica nanoparticles (Hollow MSNs) were synthesized using dodecyl dimethyl(3-sulfopropyl)ammonium hydroxide (DDAPS), sodium dodecyl sulfate (SDS), and triethanolamine as structure-directing agents, and tetraethyl orthosilicate (TEOS) and N-trimethoxysilypropyl-N,N,N-trimethylammonium chloride (TMAPS) as silica sources under basic condition via the sol-gel process. The structure and morphology of the alkylammonium-functionalized hollow mesoporous silica nanoparticles (Hollow MSN-N+CH3) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption-desorption analysis, and Fourier-transform infrared (FT-IR) spectroscopy. The functionalized hollow MSNs had a particle size of about 450 nm and a shell thickness of about 60 nm with uniform size. The nanoparticle had a surface area of 408 m2g-1, pore volume of 0.8 cm3g-1 and a uniform pore diameter of 45.9 Å. In the cancer cell viability test with MCF-7 cell, fludarabine-incorporated and alkylammonium-functionalized hollow mesoporous silica nanoparticles (Flu/Hollow MSN-N+CH3) showed excellent cancer cell death comparable with pure fludarabine drug with the controlled drug release by pH stimuli. It is considered that our current materials have the potential applicability as pH-responsive nanocarriers in the field of cancer therapy.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

Supplementary cementitious materials (SCMs) are increasingly used in precast concrete industry to enhance concrete strength and durability. SCMs of large market share in precast concrete in-dustry include silica fume, also known as micro-silica and class C fly ash. The main objective of this research is to develop non-proprietary high strength concrete mixes for precast/prestressed concrete industry. Two SCMs are used simultaneously in partial replacement of portland cement to develop ternary mixes. Class c fly ash and silica fume incorporation in the mix design, in ad-dition to low water-to-powder ratio resulted in the successful development of high strength mixes with minimum 24-hour strength in excess of 70 MPa and a final compressive strength ex-ceeding 100 MPa at 28 days. Mechanical properties testing of developed concrete mixes showed that SCMs incorporation resulted in increased values for hardened concrete modulus of elasticity (MoE) and modulus of rupture (MoR). The enhanced concrete properties, mainly high early strength, are highly required in precast concrete industry as it allows for increased productivity of precast facilities and the possibility of pouring high strength slender sections for prestressed concrete applications

Expansive soil shows dual swell-shrink which is not suitable for the construction. Several mitigating techniques exist to counteract the problem promulgate by expansive clayey soils. This paper explored the penitential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis is made in three phases which involved the tests on mechanical reinforced expansive soil using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and 12mm length. The second phase of experiments carried out on chemical stabilized expansive soil with different percentages (2%, 4% and 8%) of silica and next phase of the experimental focused in the combination of mecho-chemical stabilization of the expansive soil with different combination of silica (i.e., 2%, 4% and 8%) and polypropylene fibers (i.e., 0.25%, 0.50% and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI) grain size, and constant volume swelling pressure test were performed on unreinforced and reinforced expansive soil to investigate the effect of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber.

Highly colloidal Eu-doped Gd2O3 nanoparticles(core-NPs) were synthesized by thermal decomposition via weak base at low temperature (150oC), subsequently, silica layers were deposited to increased colloidal stability, solubility, biocompatibility and no-toxicity at the environmental condition. XRD results indicate the highly purified, crystalline, single phase cubic phase Gd2O3 nanocrystals. TEM image shows the mesoporous thick silica layer was effectively coated over the core nanocrystals, which have irregular size with nearly spherical shape and a mean grain size is about 10-30 nm. Absorption spectra and zeta potential results in aqueous media revealed that solubility, colloidal stability, and biocompatibility character was enhanced from core to core-shell structure because of silica layer surface encapsulation. The samples demonstrate excellent photoluminescence properties (dominant emission 5D0→7F2 transition in red region at 610 nm) indicated the advantage to use in optical bio-detection and bio-labeling etc. The photoluminescence intensity of the silica shell modified core/shell nanoparticles were suppressed relatively core-nanoparticles, it indicates the multi-photon relaxation pathways arising from the surface coated high vibrational energy molecules of the silanol groups. The core/nSiO2/mSiO2 nanocrystals display strong emission (5D0→7F2) transition along with excellent solubility and biocompatibility, which may find promising applications in photonic based biomedical applications.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Studying the distribution and transport dynamics of cations in plants is crucial for understanding their response mechanisms to saline-alkali stress conditions. However, our current understanding of how restoration measures affect cation distribution and transport in plants is surprisingly limited. To address this gap, we conducted a split-plot experiment using Medicago sativa L. cv. “Zhongmu No. 1” to investigate the combined effects of biological and chemical restoration measures—with bio-fertilizer as the primary zone and flue gas desulfurization (FGD) gypsum with humic acid as the secondary zone—on soil properties, plant growth, and the content, distribution, and transport of cations in plants. The results revealed that different restoration strategies decreased soil alkalinity and enhanced plant growth. Significantly, bio-fertilizer exhibited positive effects on plant growth and yield. On the contrary, FGD gypsum with humic acid reduced the soil's pH level, exchangeable sodium percentage, and sodium adsorption ratio, while increasing the contents of K+, Ca2+, and Mg2+ in the soil. The triple combination of FGD gypsum and humic acid with bio-fertilizer reduced Na+ transport in M. sativa by enhancing the selective absorption of beneficial ions, such as K+, Ca2+, and Mg2+ in leaves, and by facilitating the transport of Ca2+ and Mg2+ from roots and stems to the leaves. Therefore, the application of FGD gypsum and humic acid combined with bio-fertilizer has the potential to decrease soil alkalinity and the proportions of water-soluble ions in the soil, ultimately enhancing the translocation of key ionic components to leaves. This, in turn, increases the salt tolerance of plants and promotes their growth. Our results offer new insights into the interactions among measures, soil, and plants in saline-alkali land restoration, providing practical solutions for the restoration of saline-alkali soil.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

Hydrogels can offer many opportunities for drug delivery strategies. They can be used on their own or their benefits can be further exploited in combination with other nanocarriers. Intelligent hydrogels that react to changes in the surrounding environment can be utilized as gatekeepers and provide sustained on demand drug release. In this study, a hybrid nanosystem for tempera-ture and pH sensitive delivery was prepared from MCM-41 nanoparticles grafted with newly synthesized thermosensitive hydrogel (MCM-41/AA-g-PnVCL). The initial particles were chemi-cally modified by carboxyl groups attachment. Later, they were grafted with agar (AA) and vi-nylcaprolactam (VCL) by free radical polymerization. Doxorubicin was applied as a model hy-drophilic chemotherapeutic drug. The successful formulation was confirmed by FT-IR and TGA. Transmission electron microscopy and dynamic light scattering analysis showed small particles with negative zeta potential. Their release behaviour was investigated in vitro in different pH media and at different temperatures. At tumor simulating conditions (40ºC and pH 4.0) doxoru-bicin was almost completely released within 72 hours. The biocompatibility of the proposed na-noparticles was demonstrated by in vitro haemolysis assay. These results suggest the possible parenteral application of the newly prepared hydrogel-functionalized mesoporous silica nanopar-ticles for temperature-sensitive and pH-triggered drug delivery at the tumor site.

The risk of lung exposure to silica nanoparticles (SiNPs) and related lung inflammatory injury is increasing with the wide application of SiNPs in a variety of industries. A growing body of research has revealed that cyclooxygenase (COX)-2/ prostaglandin E2 (PGE2) up-regulated by SiNPs toxicity has a role during pulmonary inflammation. The detailed mechanisms underlying SiNPs-induced COX-2 expression and PGE2 synthesis remain unknown. The present study aims to dissect the molecular components involved in COX-2/PGE2 up-regulated by SiNPs in human pulmonary alveolar epithelial cells (HPAEpiCs) which are one of the major targets while SiNPs are inhaled. In the present study, we demonstrated that SiNPs induced COX-2 expression and PGE2 release, which were inhibited by pretreatment with a reactive oxygen species (ROS) scavenger (edaravone) or the inhibitors of proline-rich tyrosine kinase 2 (Pyk2, PF-431396), epidermal growth factor receptor (EGFR, AG1478), phosphatidylinositol 3‑kinase (PI3K, LY294002), protein kinase B (Akt, Akt inhibitor VIII), p38 mitogen-activated protein kinase (MAPK) (p38 MAPK inhibitor VIII), c-Jun N-terminal kinases (JNK)1/2 (SP600125), Forkhead Box O1 (FoxO1, AS1842856), and activator protein 1 (AP-1, Tanshinone IIA). In addition, we also found that SiNPs induced ROS-dependent Pyk2, EGFR, Akt, p38 MAPK, and JNK1/2 activation in these cells. These signaling pathways induced by SiNPs could further cause c-Jun and FoxO1 activation and translocation from the cytosol to the nucleus. AP-1 and FoxO1 activation could increase COX-2 and PGE2 levels induced by SiNPs. Finally, the COX-2/PGE2 axis might promote the inflammatory responses in HPAEpiCs. In conclusion, we suggested that SiNPs induced COX-2 expression accompanied by PGE2 synthesis mediated via ROS/Pyk2/EGFR/PI3K/Akt/p38 MAPK- and JNK1/2-dependent FoxO1 and AP-1 activation in HPAEpiCs.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

In this work, polyacrylic acid-functionalized MCM-41 was synthesized, which was further interacted with calcium ions, to realize enhanced pH-responsive nanocarrier for sustained drug release. First, mesoporous silica nanoparticles (MSNs) were prepared by the sol-gel method. Afterward, (3-trimethoxysilyl)propyl methacrylate (TMSPM) modified surface was prepared by using the post-grafting method, then polymerization of acrylic acid was proceeded. After adding calcium chloride solution, polyacrylic acid-functionalized MSNs with calcium-carboxyl ionic bonds in the polymeric layer, which can prevent the cargo from leaking out of the mesopore, were prepared. The structure and morphology of the modified nanoparticles (PAA-MSNs) were characterized by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM), and N2 adsorption-desorption analysis, etc. The controlled release of guest molecules was studied by using 5-fluorouracil (5-FU). The drug molecules-incorporated nanoparticles showed different releasing rates under different pH conditions. It is considered that our current materials have the potential as pH-responsive targeted nanocarriers in the field of medical treatment.

Background: Work experience is a key factor that influences safety awareness among workers. This study investigated the influence of work experience on the level of awareness on adverse health effects of silica dust exposure among stone quarry workers in Ghana while controlling for theoretically relevant compositional and contextual factors, evaluated the magnitude and order of association between the predictors and the predicted variable. Method: A cross-sectional survey data of 524 randomly selected stone quarry workers were subjected to multivariate statistical analyses. Results: Stone quarry workers who had 6 to10 years and more than 10 years of work experience were 48% (OR = 1.475, P = 0.021) and 82% (OR = 1.816, P = 0.003) respectively more likely to be aware of the adverse health effects of silica dust exposure compared to their counterparts who had 1 to 5 years work experience. Workers who had secondary or higher education were 32% (OR = 1.320, P = 0.036) more likely to be aware of the adverse health effects of silica dust exposure compared to their counterparts who had no education. Conclusion: These findings provide relevant information for managers and policymakers to plan and maximize awareness on silica dust health hazards among silica exposed workers.

Nanoparticles (NPs) have various applications in medicine, cosmetics, optics, catalysis, environmental purification, and other areas nowadays. With an increasing annual production of NPs, the risks of their harmful influence to the environment and human health is rising. Currently, our knowledge about the mechanisms of interaction between NPs and living organisms is limited. Additionally, poor understanding of how physical and chemical characteristic and different conditions influence the toxicity of NPs restrict our attempts to develop the standards and regulations which might allow us to maintain the safe living conditions. The marine species and their habitat environment are under continuous stress due to anthropogenic activities which result in the appearance of NPs in the aquatic environment. Our study aimed to evaluate and compare biochemical effects caused by the influence of different types of carbon nanotubes, carbon nanofibers, and silica nanotubes on four marine microalgae species. We have evaluated the changes in growth-rate, esterase activity, membrane polarization, and size changes of microalgae cells using flow cytometry method. Our results demonstrated that toxic effects caused by the carbon nanotubes strongly correlated with the content of heavy metal impurities in the NPs. More hydrophobic carbon NPs with less ordered structure had a higher impact on the red microalgae P. purpureum because of higher adherence between the particles and mucous covering of the algae; silica NPs caused significant inhibition of microalgae growth-rate predominantly produced by mechanical influence.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

Nowadays the preservation and restoration of historical building needs to be faced in accordance with a novel sensibility regarding environment to preserve the future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques allowing durability and mechanical performances and at the same time compatibility with the existing heritage. Alkali activated materials represent a great challenge to produce new materials starting from the existing ones with reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorization of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, then the geopolymeric samples produced were characterized from physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for historical buildings recovery. Brick waste based geocomposites resulted to be more compact than the tuff-based ones as showed by the higher density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials and to all the traditional repairing products.

Soarinho Alkaline Intrusion, southeastern Brazil, makes part of the Serra do Mar Igneous Province, and it is composed of alkali feldspar syenite, alkali feldspar trachyte, quartz syenite, and mon-zonite. Geochemical and geochronological analysis of the Soarinho were compared with data from its neighbors Rio Bonito and Tanguá. Zircon U-Pb Laser Ablation ages show that Soarinho is youngest than Rio Bonito and Tanguá. Ages obtained from the monzonite (60 ± 2 Ma), alkali feldspar syenite (58 ± 2 Ma), and quartz syenite (58 ± 2 Ma) are indistinguishable within error. Petrographic and geochemical data show a clear contrast among Soarinho, Rio Bonito, Tanguá, and Lu-Hf isotopic data for the three alkaline intrusions (all negative), point to some similarities in their sources. The data suggest an enriched mantle source for Soarinho; however, an older con-tinental crust contribution cannot be discarded.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

Influence of particle size on the mechanical strength of alkali activated material from waste refractory monolithic was investigated in this study. Precursor was chemically and mineralogically analysed, separated on 4 fractions and alkali activated with Na-water glass. Alkali activated materials were thoroughly investigated under SEM and XRD to evaluate the not predicted differences in mechanical strength. Time dependence of curing temperature on mechanical strength was investigated in the sample prepared from a fraction that caused the highest compressive strength.

Mesoporous silica nanoparticles (MSNs) can be used as carrier materials for the controlled release of pesticides while reducing their negative environmental impact. In this study, we screened an active ingredient, p-cymene (PC), with an excellent inhibitory effect on rice bacterial blight. Subsequently, the PC was successfully loaded onto MSNs via physisorption(PC@MSNs). PC@MSNs, characterized by a regular spherical shape, smooth surface, and an MSN average size of 262.9 nm, achieved an 8.6 % drug loading capacity. The release kinetics of the PC from the PC@MSNs demonstrated a sustained release (288 h) pattern influenced by drug diffusion. The efficacy of the PC@MSNs against Xanthomonas oryzae pv. Oryzae paralleled those of PC. Acute toxicity assays re-vealed that the PC@MSNs were less toxic to aquatic life (LC50=257.867 mg/L) and that the formu-lation showed no adverse effects on rice seedling growth. In summary, these results suggest that PC@MSNs can broaden PC's application scope in managing rice diseases.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

The present study concerns the application of electrochemical chloride extraction to concrete designed with partial replacements of Ordinary Portland Cement (OPC) from different binders, namely ground granulated blast furnace (GGBS), pulverized fly ash (PFA) and Silica Fume (SF), to attend the need of corrosion repair for modern constructions. Electrochemical Chloride Extraction (ECE) was applied to the specimens at a current density of 2A/m2 for 4 weeks. The chloride types and binding mechanisms appeared to have important implications on the different performance of treatment perceived for all binders. Considering total chlorides, removal was more significant for OPC and GGBS when compared to others. The main difference noted was that for GGBS the removal of bound chlorides was more significant due to a possible release of adsorbed chlorides from the silicate hydrates, present at higher intensities in this case. However, even though GGBS had greater rates of bound chloride removal it had still the same percentage as OPC for total efficiency due to the fact that in OPC the removal of free chlorides is more expressive.

Reinforcement corrosion due to chloride attack is of major economic significance for reinforced concrete structures. Pozzolans are known to inhibit corrosion initiation mainly by reducing concrete permeability. However, there is evidence in the literature that changes in the chemical environment in the concrete due to the pozzolans may be creating improved corrosion resistance, by themselves. In this study, the composition of a pore solution of mature hydrated cement paste containing silica-fume at different ratios was analyzed. The electrochemical behavior of reinforcing steel was studied in simulated pore solutions with silicate concentrations ranging from 0 to 35.6 mM, which are within the concentration range found by pore solution extraction to be up to 49 mM. Polished reinforcing steel specimens were used for cyclic voltammetry in simulated pore solutions with chloride concentrations of 10-20%. Better corrosion protection was found with increasing silicate concentration up to 3.56 mM. This was indicated by lower corrosion currents both in the passive state and after anodic activation. Anodic activation of steel in a 35.6 mM silicate solution with 20% NaCl yielded a higher potential than the anterior potential.

The silanol activity and trace metal detection methods for chemically bonded silica gels were evaluated in silico. Test compounds with large molecular sizes may demonstrate negative results because of the possibility of indirect hydrogen bonding via short alkyl groups or siloxane of the silica gels. This hypothesis was based on the observation of weak hydrogen bonding energy values similar to those observed in the study of the alkyl group effect on the hydrogen bonding of alkanols. Consequently, smaller molecules may be a better choice for the analysis of bonded-phase quality.

This work describes the preparation of mesoporous silica by the green reaction of rice husk ash (RHA) with glycerol, followed by the modification and the potential use as a drug carrier. The reaction was carried out at 215 °C for 2 h. The solution was further hydrolyzed with deionized water and aged for various times (24, 48, 120, 360, 528 and 672 h) before calcinations at 500 oC for 24 h. Further treatment of prepared mesoporous silica was performed using trimethylmethoxysilane (TMMS) to obtain hydrophobic Mesoporous silica. For all synthesized silica, silica contents were as high as 95%wt, whereas organic residues were less than 3%wt. RHA-glycerol showed the highest specific surface area with smallest pore diameter (205.70 m2/g, 7.46 nm) when aged for 48 h. The optimal hydrolysis-ageing period of 120 h resulted in 500.7 m2/g BET surface area, 0.655 cm3/g pore volume and 5.23 nm pore diameter. The surface modification of RHA-glycerol was succeeded through the reaction with TMMS as confirmed by FTIR. Ibuprofen was selected as a model drug for the adsorption experiments. The adsorption under supercritical CO2 was carried out at isothermal temperature of 40 ˚C and 100 bar, % ibuprofen loading of TMMS modified mesoporous silica (TMMS-g-MS) was 6 times less than mesoporous silica aged for 24 h (MS-24h) due to the hydrophobic nature of modified mesoporous silica, not surface and pore characteristics. The release kinetics of ibuprofen-loaded mesoporous silicas were also investigated in vitro. The release rate of ibuprofen-loaded MS-24h was much faster than that of ibuprofen-loaded TMMS-g-MS, but comparable to the crystalline ibuprofen. The slower release rate was attributed to the diffusion control and the stability of hydrophobic nature of modified silica. This would allow the design for the controlled release drug delivery system.

Some peptide-based drugs including oxytocin, vasopressin, ziconotide, pramlintide, nesiritide, and octreotide, contain one intramolecular disulfide bonds. A novel and reusable monodispersed silica nanosphere-supported Pt(IV) complex (SiO2@TPEA@Pt(IV)) was synthesized via a four-step procedure and used for formation of intramolecular disulfide bonds in peptides. TEM and chemical mapping results for the Pt(II) intermediates and for SiO2@TPEA@Pt(IV) show that the silica nanospheres possess a monodisperse spherical structure and contain uniformly distributed Si, O, C, N, Cl, and Pt. The valence state of Pt on the silica nanospheres was characterized by XPS. The Pt(IV) loaded on SiO2@TPEA@Pt(IV) was 0.15 mmol/g, as determined by UV-vis spectrometry. Formation of intramolecular disulfides in six dithiol-containing peptides of variable lengths by use of SiO2@TPEA@Pt(IV) was investigated and the relative oxidation yields were determined by HPLC. In addition, peptide 1 (Ac-CPFC-NH2) was utilized to study the reusability of SiO2@TPEA@Pt(IV). No significant decrease in the relative oxidation yield was observed after ten reaction cycles. Moreover, the structure of SiO2@TPEA@Pt(IV) after being used ten cycles was determined to be similar to its initial one, demonstrating the cycling stability of the complex.

In this study, the changes in mass, compressive strength and length were analyzed to investigate sulfate resistance according to ground granulated blast furnace slag (GGBFS) blending ratio and type of sulfate solution. All alkali activated mortars showed excellent sulfate resistance when immersed in sodium sulfate (Na₂SO₄) solution. However, when immersed in magnesium sulfate (MgSO₄) solution, different sulfate resistance results were obtained depending on the presence of GGBFS. Alkali activated GGBFS blended mortars showed a tendency to increase mass, increase length and decrease compressive strength when immersed in magnesium sulfate solution, but the alkali activated FA mortars did not show any significant difference depending on the types of sulfate solution. The deterioration of alkali activated GGBFS blended mortars in the immersion of magnesium sulfate solution was confirmed by the decomposition of C-S-H which is the reaction product by magnesium ion and the formation of gypsum (CaSO₄·2H₂O) and brucite (Mg(OH)₂).

Gold nanoclusters (AuNCs) with fluorescence in the Near Infrared (NIR) by both one- and two-photon electronic excitation were incorporated in mesoporous silica nanoparticles (MSNs) using a novel one-pot synthesis procedure where the condensation polymerization of alkoxysilane monomers in the presence of the AuNCs and a surfactant produce hybrid MSNs of 49 nm diameter. This method was further developed to prepare 30 nm diameter nanocomposite particles with simultaneous NIR fluorescence and superparamagnetic properties, with a core composed of superparamagnetic manganese ferrite nanoparticles (MnFe2O4) coated with a thin silica layer, and a shell of mesoporous silica decorated with AuNCs. The nanocomposite particles feature NIR-photoluminescence with 0.6% quantum yield and large Stokes shift (290 nm), and superparamagnetic response at 300 K, with a saturation magnetization of 13.4 emu g-1. The conjugation of NIR photoluminescence and superparamagnetic properties in the biocompatible nanocomposite has high potential for application in multimodal bioimaging.

Nanocomposite hydrogels offer remarkable potential for applications in bone tissue engineering. They are synthesized through the chemical or physical crosslinking of polymers and nanomaterials, allowing for the enhancement of their behaviour by modifying the properties and compositions of the nanomaterials involved. However, their mechanical properties require further enhancement to meet the demands of bone tissue engineering. Here, we present an approach to improve the mechanical properties of nanocomposite hydrogels by incorporating polymer grafted silica nanoparticles into a double network inspired hydrogel (gSNP Gels). The gSNP Gels were synthesised via a graft polymerization process using a redox initiator. gSNP Gels were formed by grafting 2-acrylamido-2-methylpropanesulfonic acid (AMPS) as the first network gel followed by a sequential second network acrylamide (AAm) onto amine functionalized silica nanoparticles (ASNPs). We utilized glucose oxidase (GOx), to create an oxygen-free atmosphere during polymerization resulting in higher polymer conversion compared to argon degassing. The gSNP Gels showed excellent compressive strengths of 13.9 ± 5.5 MPa, a strain of 69.6 ± 6.4%, and a water content of 63.4% ± 1.8. The synthesis technique demonstrates a promising approach to enhance the mechanical properties of hydrogels, which can have significant implications for bone tissue engineering and other soft tissue applications.

Insects quickly develop resistance to conventional chemical insecticides. The use of silica nanoparticles (SiO₂NPs) is a promising new approach for managing insect pests. The insects that have been studied are, in most cases, external feeders and internal leaf feeders have not been well studied. Here, we investigate the efficiency of SiO₂NPs in controlling the American serpentine leafminer Liriomyza trifolii (Diptera: Agromyzidae), a devastating insect pest of a wide range of crops. SiO₂NPs at concentrations of 50, 100, 200 and 400 mg/L compared to a control of distilled water were applied to intact Phaseolus vulgaris leaves by spraying to evaluate their effects, via the plant, on the number, survival, developmental/feeding speed, body mass/size and sex ratio of L. trifolii released after spraying. A qRT-PCR analysis was conducted to assess oxidative stress in L. trifolii based on the gene expression level of the two major antioxidant enzymes; catalase and superoxide dismutase. The number of mines, survival rate and puparia weight were lower than the control at the highest concentration of SiO₂NPs, while pupariation was delayed at most of the concentrations studied and puparium weight/size decreased at low concentrations. Sex ratio was not affected by SiO₂NPs. Gene expression levels of the antioxidant enzymes at the pupal stage were not significantly affected by SiO₂NPs at any concentration but some individuals showed up-regulation at low SiO₂NP concentrations, inferring development of resistance. This study demonstrated that a priori application of the highest concentration of SiO₂NPs to plants effectively reduces a leafminer population but that application of even the lowest concentration can decrease the life history trait values of surviving leafminers.

This study's objective was to propose the use of textile braiding manufacturing methods, thus facilitating the application of the high precision and accurate measurability of optical fiber Bragg grating sensors to various structures. The purpose of this study was to Combine 3d braid processing with the optical Bragg grating sensor's accurate metrology. Out of limits of the sensor's epoxy attachment methods, the textile braiding method can make applicable scope diversify. The braiding processing is capable of designing a 3D fabric module processing, multiple objective mechanical fiber arrangement, and material characteristics. Optical stress-strain response conditions were explored through the optimization of design elements between the Bragg grating sensor and braiding. For this study, Bragg grating sensors were located 75% apart from the fiber center. The sensor core structure is helical of 1.54 pitch. A polyurethane synthetic yarn was braided together with the sensor on the Weaving machine core part in a braiding. Prototyping results, a negative Poisson's ratio makes curled the braided Bragg grating sensor. The number of polyurethane string yarns has been conducted the role of wrap angle in braiding. The 12 strands condition showed an increase in double stress-strain response rate at a Poisson ratio of 1.3%, and 16 strands condition was found to affect the sensor with noise at a Poisson ratio of 1.5%. This study can suggest applying braid processing of the Bragg grating sensor, which is expected to create and develop a new monitoring sensor.

This study's objective was to propose the use of textile braiding manufacturing methods, thus facilitating the application of the high precision and accurate measurability of optical fiber Bragg grating sensors to various structures.The purpose of this study was to Combine 3d braid processing with the optical Bragg grating sensor's accurate metrology. Out of limits of the sensor's epoxy attachment methods, the textile braiding method can make applicable scope diversify. The braiding processing is capable of designing a 3D fabric module processing, multiple objective mechanical fiber arrangement, and material characteristics. Optical stress-strain response conditions were explored through the optimization of design elements between the Bragg grating sensor and braiding. For this study, Bragg grating sensors were located 75% apart from the fiber center. The sensor core structure is helical of 1.54 pitch. A polyurethane synthetic yarn was braided together with the sensor on the Weaving machine core part in a braiding.Prototyping results, a negative Poisson's ratio makes curled the braided Bragg grating sensor. The number of polyurethan string yarns has been conducted the role of wrap angle in braiding. The 12 strands condition showed an increase in double stress-strain response rate at a Poisson ratio of 1.3%, and 16 strands condition was found to affect the sensor with noise at a Poisson ratio of 1.5%. This study can suggest applying braid processing of the Bragg grating sensor, which is expected to create and develop a new monitoring sensor.

The adsorption of carbon dioxide on amino silanes-functionalized MCM-41 and SBA-15 materials is reported. The functionalization of mesoporous silicas was made by post-synthesis method, by impregnation of 3-aminopropyltriethoxysilane. The obtained materials were characterized by X-ray diffraction, scanning and transmission electron microscopies, nitrogen adsorption-desorption and X-ray photoelectron spectroscopy measurements. The carbon dioxide adsorption capacities for the samples were carried out under ambient pressures. The obtained results evidenced that amino-silanes with a terminal amine (–NH₂) were functionalized through covalent coupling of this group on the surface of the channels in the ordered mesoporous silica, meaning that the amine is anchored on the surface of the bigger pores of the MCM-41 and SBA-15 support. For functionalized materials, the CO₂ adsorption capacity of the AMCM-41 increased from 0.18 to 1.1 mmol·g⁻¹, whereas for ASBA-15, it was from 0.6 to 1.8 mmol·g⁻¹. The Lagergren kinetic algorithms were applied in order to validate the obtained results, evidencing the enhanced carbon dioxide adsorption capacity and stability of the functionalized ordered mesoporous molecular sieves.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

The annual construction and demolition waste (CDW) generated from EU construction sector was 850 million tons, which represented 31% of the total waste generation and about 28% of CDW was ceramics (bricks and tiles). In this study, the feasibility of using CDW brick powder as the precursor of alkali activated mortar (AAM) and extruded polystyrene (XPS) as the lightweight aggregates to form lightweight brick powder AAM (LW-BP-AAM) for non-structural applications was investigated. The thermal conductivity of LP-BPAAM was 0.112 W/m·K with density of about 1,135 kg/m³ which was lower than the counterparts with similar density in literature. The acid resistance of LW-BP-AAM is comparable to conventional fly ash based AAM and superior than ordinary Portland cement. From the scanning electron microscopy with energy dispersive X-ray spectroscopy, there was no severe damage on the surface of LW-BP-AAM but aluminate was removed from the matrix which was further verified in Fourier transform infrared spectroscopy. The mass and strength loss of LP-BP-AAM was 1.5% and 33%, respectively. Although the compressive strength of the LP-BP-AAM was low (about 1.8 MPa), it can be improved by optimising the particle size of the XPS aggregates.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

In tire tread applications, achieving enhanced abrasion resistance, wet grip, and rolling resistance is crucial for optimizing overall performance. To realize improvements in these attributes for silica-filled tire tread compound, it becomes imperative to improve dispersity of silica filler with investigating the effect of each component in tire tread compound. In this work, we study the effect of styrene content within solution styrene butadiene rubber (SSBR) on the properties of tire tread compounds. A higher styrene segment within SSBR contributes to increased silica dispersion and crosslink density. Thus, tire tread compounds featuring SSBR with increased styrene content not only improve physical and mechanical properties but also enhance major characteristics tailored for tire tread applications. These findings provide valuable insights into advancing the reinforced performance of tire tread compounds through the strategic utilization of SSBR enriched in styrene content.

Polyhedral Oligomeric Silsesquioxanes (POSS) are one of the smallest silica nano particles. The presence of ordered ladder-like or cage conformation in their structure leads to remarkable thermal stability far greater than that for a linear polysiloxane. Reinforcement with nano particles is one of the recently favored strategy used to enhance the performance of polymers materials. The cyclic silica structure present in POSS ensures excellent thermal and mechanical stability. As a reinforcing filler, POSS can enhance the resistance of polymer matrix against pyrolysis and corrosion. In this paper, amine-terminated POSS with ladder like structure was synthesized by condensation of hydrolyzed aminosilane coupling agent. The ladder-like structure of POSS severely limits the motion of the chain backbone. The absence of phase transition for the synthesized POSS was confirmed by differential scanning calorimetry (DSC). Thermogravimetric analysis (TGA) was utilized to evaluate the thermal stability of POSS. TGA data show that the ladder-like POSS reported here has high char yield of about 75 % in nitrogen atmosphere and 54% in air atmosphere at 800℃. The TGA derivative curves show that the degradation of ladder-like POSS involves multiple stages and that the degradation rate is directly proportional to the heating rate. With the aid of Fourier Transform Infrared Spectroscopy (FT-IR), the cyclic structure of Si-O-Si bonding was determined to be the predominant structure. By analyzing the FTIR spectra of the cured POSS residue obtained at the specified temperatures, the detailed degradation mechanism of POSS was inferred. From the FTIR spectra of the low temperature cured samples, it was shown that the terminal silanol group was eliminated below 400℃. Some intermediate polymeric siloxane structures were observed by means of FT-IR and they eventually transitioned into silica which is the final product of pyrolysis of POSS. The presence of the FTIR transmission peaks at 1000 and 1100 cm-1, due to asymmetrical vertical and horizontal stretching of Si-O-Si, were the key evidence for the inferred ladder-like structure of POSS.

Several lime mortars for the repair of painted plasters of the rock cut church of Ss. Pietro and Paolo in Matera were studied. They were designed taking into account both aesthetic criteria that need to be fulfilled in the field of paintings restoration, and physical-mechanical compatibility with the original materials on site, i.e. the pre-existing plasters and the supporting rock. Mixes with calcareous and silica aggregates, based on different grain size proportions, were prepared for filling missing portions of the original painted plaster. The effects of the mineralogical nature and size of the aggregates on the characteristics and properties of the mixes were investigated in relation to the microstructure, physical-mechanical features and resistance to salt ageing. At the end of the experimental campaign, the overall performances were evaluated.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

As the field of nanoscience is rapidly evolving, interest for novel, upgraded nanomaterials with combinatory features is also inevitably increasing. Hybrid composites, offer simple, budget-conscious and environmental-friendly solutions that can cater multiple needs at the same time and be applicable in many nanotechnology-related and interdisciplinary studies. The physicochemical idiocrasies of dendritic polymers have inspired their implementation as sorbents, active ingredient carriers and templates for complex composites. Ceramics are distinguished for their mechanical superiority and absorption potential that render them ideal substrates for separation and catalysis technologies. The integration of dendritic compounds to these inorganic hosts can be achieved through chemical attachment of the organic moiety onto functionalized surfaces, impregnation and absorption inside the pores, conventional sol-gel reactions or via biomimetic mediation of dendritic matrices, inducing the formation of usually spherical hybrid nanoparticles. Alternatively, dendritic polymers can propagate from ceramic scaffolds. All these variants are covered in detail. Optimization techniques as well as established and prospected applications are also presented.

Conventional radiation therapy uses white X-rays that consist of a mixture of X-ray waves with various energy levels. In contrast, a monochromatic X-ray (monoenergetic X-ray) has a single energy level. Irradiation of high Z elements with a synchrotron generated monochromatic X-ray with the energy at or higher than the K-edge energy of the element results in the production of the Auger electrons that cause DNA damage leading to cell killing. Delivery of high Z elements into cancer cells and tumor mass can be facilitated by the use of nanoparticles. Mesoporous silica nanoparticles (MSNs) have been shown to be effective in delivering high Z elements to cancer cells. A proof of principle experiment was reported that demonstrated the feasibility of this approach. This opens up a possibility to pursue the Auger cancer therapy by the combined use of MSNs loaded with high Z elements and monochromatic X-rays. Similar cancer therapies using other types of quantum beams such as neutron, proton and carbon ion beams can be envisioned.

During the casting in a warmer tropical temperature, a setting time delay is required to maintain the workability of the concrete, commonly achieved by the addition of admixtures i.e. silica fume (SF), fly ash (FA), and Plastrocrete®. However, high sugar content Coca-Cola in niche conditions is proposed as an ingredient for delaying concrete setting time in combination with conventional admixtures. This research aims to compare the setting time of admixtures from Coca-Cola and Plastocrete® RT6 plus in concrete mixing with control data of concrete mixed with SF or FA. The second aim is to measure the compression strengths between combinations of Coca-Cola and Plastocrete® RT6 plus. Concretes were produced with admixtures of SF, FA, Plastocrete® RT6plus, or Coca-Cola. The concrete used to control was f'c20 and f'c 25, while other concrete mixes were produced with the addition of Coca-Cola at 0.15% from the weight of cement at variation of moisture treatments. The first method to produce concrete (f'c20+Plas0.23%+Cola0.15% and f'c25+Plas0.23%+Cola0.15%) did not employ water reduction. The second concrete productions (f'c25+Plas0.46%+Cola0.15% and f'c25+Plas0.46%+Cola0.15%) reduced the addition of water at 8.8% (v/w). The first concrete production method had a setting time 44% longer than control. The reduced water concrete in the second productions had a setting time 34% longer than control. Meanwhile, the Plastocrete® RT6 Plus admixture with the reduced water delayed the concrete setting time by 26% longer than control. The delayed setting time of Plastocrete® RT6 Plus admixture with reduction of water was shorter than in the treatment with Coca-Cola. The combination of the addition of Coca-Cola with Plastocrete® RT6 plus by reducing the amount of adding Coca-Cola to 0.10% with Plastocrete® RT6 plus can delay concrete setting time by 51% longer than normal concrete and increase concrete compressive strength by 13% higher than normal concrete. Mixing Coca-Cola with Plastocrete® RT6 plus not only provided an optimal delay effect on setting time but also significantly increase the compressive strength that was desired during the casting in warm tropical weather applied in building construction of Mulawarman University, Samarinda, Indonesia.

Forensic detection of non-volatile nitro explosives poses a tough analytical challenge. A colorimetric sensor comprising ultrasonically prepared silica-dye microspheres was developed for sensitive gas detection of cyclohexanone, a volatile marker of explosives 1,3,5-trinitro-1,3,5-triazinane (RDX) and 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX). The silica-dye composites were synthesized from the hydrolysis of ultrasonically sprayed organosiloxanes under mildly heating conditions (150 ^oC), which yields microspherical, nanoporous structures with high surface area (~300 m²/g) for gas exposure. The sensor inks were deposited on cellulose paper and gave sensitive colorimetric responses to trace amount of cyclohexanone vapors even at sub-ppm levels, with the detection limit down to ~150 ppb. The sensor showed high chemical specificity towards cyclohexanone against humidity and other classes of common solvents, including ethanol, acetonitrile, ether, ethyl acetate, and ammonia. Paper-based colorimetric sensors with hierarchical nanostructures could represent an alternative sensing materials for practical applications in the detection of explosives.

This study identifies new Alkali Activated Composite Mud Mortar to alternate Cement Mortar used for laying masonry works. This study handles both experimental and numerical analysis of strength and durability for mortar, especially bond strength along mortar and brick joints have studied detail and compared with ANSYS. The bond strength has estimated through the triplet brick prism of shear behavior. The strength and deformation characteristics of masonry constituents obtained from these tests depend on the actual composite conduct of masonry. There is always a good reception for environmentally friendly, low energy, new construction materials, and used in preparing mortar/brick unit combinations all around the world. Also, this study fulfills those requirements. Especially, masonry laid with the mud mortar meets all. Fly Ash, Ground Granulated Blast furnace Slag, and Quarry Dust have utilized the new composites' preparation with 8Molority, 10Molority developed excellent strength. The composite specimens are having compression and bond strength, ranging from 4.84-5.14 and 0.12-0.18N/mm2. The mixed ratio of materials has taken (0.5 parts of Fly Ash, 0.5 parts of Steel Slag, 1.75 parts of Soil, and 0.25 parts of Quarry Dust). The samples tested resistance against acidic, sulfate, and alkalinity indicated PH values less than 7 and 9 simultaneously. Compression strength varied from 10-20% and gained more and fit composite used for mortar in masonry works.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

Silica on Silicon is a major optical integration platform, while the emergent class of integrated Laser written circuits' platform offers additionally high customizability, and flexibility for rapid prototyping. However, the inherent waveguides' low core/cladding refractive index contrast characteristic compared to other photonic platforms in silicon or silicon nitride, sets serious limitations for on-chip efficient coupling with single photon emitters, like semiconductor nanowires with quantum dots limiting the applications in quantum computing. A new light coupling scheme proposed here overcomes this limitation providing means for light coupling >50%. The scheme is based on the incorporation of an optical microsphere between the nanowire and the waveguide, properly optimized and arranged in terms of: size, refractive index, distance of microsphere between nanowire and waveguide. Upon suitable design of the optical arrangement, the photonic nanojet emitted by the illuminated microsphere excites efficiently the guided eigenmodes of the input channel waveguide, thus launching light with high coupling efficiency. The method is tolerant in displacements, misalignments, and imperfections and is fabricationally feasible by current state of the art techniques. The proposed method enables the on-chip multiple single photon emitters' integration thus allowing the development of highly customizable and scalable quantum photonic integrated circuits for quantum computing.