Deep Learning (DL) and Machine Learning (ML) are widely used in many fields, but rarely used in Frequency Estimation (FE) and Slope Estimation (SE) of signals. Frequency and slope estimation for Frequency-Modulated (FM) and single-tone sinusoidal signals are essential in various applications, such as wireless communications, sonar, and radar measurements. In this work, artificial neural network (ANN) and convolutional neural network (CNN) are used in frequency and slope estimation for FM signals under Additive White Gaussian Noise (AWGN) and Additive Symmetric alpha Stable Noise (SαSN). SαS distributions are impulsive noise disturbances found in many communication environments like marine systems; their distribution lacks a closed-form Probability Density Function (PDF), except for specific cases, and infinite second-order statistic, hence Geometric SNR (GSNR) is used in this work to determine the impulsiveness of noise in a mixture of Gaussian and SαS noise processes. ANN is a machine learning classifier, designed with few layers for reducing FE and SE complexity while getting higher accuracy as compared with classical techniques. CNN is a deep learning classifier, designed with many layers for FE and SE, and proved to be more accurate than ANN when dealing with big data and finding optimal features. Simulation results show that SαS noise can be much more harmful for FE and SE of FM signals than Gaussian noise. DL and ML can significantly reduce FE complexity, memory cost, and power consumption, which is important in many systems such as some Internet of Things (IoT) sensor applications. After training DCNN for frequency and slope estimation of LFM signals, the performance of DCNN (in terms of accuracy) can give acceptable results at very low signal-to-noise ratios where TFD fails, giving more than 20dB difference in the GSNR working range.

Novel model of biodegradable PHA copolymer films preparation was applied to evaluate biodegradability of various PHA copolymers and discuss its biomedical applicability. In this study, we illustrate the potential biomaterial degradation rate affectability by manipulation of monomer composition via controlling biosynthetic strategies. Within the experimental investigation, we have prepared two different copolymers of 3-hydroxybutyrate and 4-hydroxybutyrate – P(3HB-co-36 mol.% 4HB) and P(3HB-co-66 mol.% 4HB), by cultivating thermophilic bacterial strain Aneurinibacillus sp. H1 and further investigated its degradability in simulated body fluids (SBFs). Both copolymers revealed faster weight reduction in synthetic gastric juice (SGJ) and artificial colonic fluid (ACF) than simple homopolymer P3HB. In addition, degradation mechanisms differed across tested polymers, according to SEM micrographs. While incubated in SGJ, samples were fragmented due to fast hydrolysis sourcing from substantially low pH, which suggest abiotic degradation as the major degradation mechanism. On the contrary, ACF incubation indicated obvious enzymatic hydrolysis. Further, no cytotoxicity of the waste fluids was observed on CaCO-2 cell line. Based on these results in combination with high production flexibility, we suggest P(3HB-co-4HB) copolymers produced by Aneurinibacillus sp. H1 as very auspicious polymers for intestinal in vivo treatments.

The large production of non-degradable petrol-based plastics has become a major global issue due to its environmental pollution. Biopolymers produced by microorganisms such as polyhydroxyalkanoates (PHAs) are gaining potential as a sustainable alternative, but the high cost associated to their industrial production has been a limiting factor. Post-transcriptional regulation is a key step to control gene expression in changing environments and has been reported to play a major role in numerous cellular processes. However, limited reports are available concerning the regulation of PHA accumulation in bacteria, and many essential regulatory factors still need to be identified. Here, we review studies where the synthesis of PHA has been reported to be regulated at the post-transcriptional level, and we analyze the RNA-mediated networks involved. Finally, we discuss the forthcoming research on riboregulation, synthetic and metabolic engineering which could lead to improved strategies for PHAs synthesis in industrial production, thereby reducing the costs currently associated with this procedure.

Many wounds are unresponsive to current available treatment techniques and therefore there is an immense need to explore suitable materials including biomaterials, which are being considered as the crucial factor to accelerate the healing cascade. In this study, we fabricated polyhydroxyalkanoate based antibacterial mats via electrospun technique. One-pot green synthesized graphene decorated silver nanoparticles (GAg) were incorporated into the fibres of poly-3 hydroxybutarate-co-12 mol% hydroxyhexanoate (P3HB-co-12mol% HHx), a co-polymer of polyhydroxyalkanoate (PHA) family which is highly biocompatible, biodegradable and flexible in nature. The synthesised PHA/GAg biomaterial was characterized by field emission scanning electron microscopy (FESEM), elemental mapping, thermogravimetric analysis (TGA), UV-visible spectroscopy (UV-vis) and Fourier transform infrared spectroscopy (FTIR). In-vitro antibacterial analysis were performed to investigate the efficacy of PHA/GAg against gram positive Staphylococcus aureus (S.aureus) strain 12600 ATCC and gram negative Escherichia coli (E.coli) strain 8739 ATCC. The results indicated that the PHA/GAg demonstrated significant reduction of Staphylococcus aureus (S.aureus strain 12600 ATCC) and Escherichia coli (E.coli strain 8739 ATCC) as compared to bare PHA or PHA-rGO in 2 hours of time. The P value (P< 0.05) was obtained by using 2 sample T-test distribution.

Parts of shotgun cartridges are a significant source of plastic litter in the marine environment. Empty cartridge shells may not be picked up by the hunter who fired them, and plastic wads that serve to separate the propellant from the shot load, are lost down-range when a shot is fired. Such litter items constitute a cosmetic and aesthetic problem on coastlines and may cause harm to marine animals and in the later stages of decomposition break down into harmful micro plastic particles. There exists no reliable estimate of the global exposure of marine ecosystems to this plastic source. However, in some countries it has been subject to closer examination, including for example, Denmark where the annual contribution of plastic wads into marine systems was estimated to 600,000 pieces (c2 tonnes), and the accumulated density of washed-up items (both wads and shells) was 3.7 items per 100 m coastline. Increasing awareness of this problem has caused scientists, hunters’ communities and governments to suggest altered practice including transition to the use of biodegradable cartridge components, first and foremost wads as this item is invariable lost during hunting. Several manufacturers provide shotgun cartridges containing biodegradable wads based on different types of materials, including fibers and various types of plastics, for example PVAL (poly(vinyl alcohol)) and PHA (polyhydroxyalkanoate). In this paper, we review the most recent literature on the amounts and related environmental hazards of plastic dispersed from hunting ammunition into marine ecosystems. We summarize the market availability of shotgun cartridges with biodegradable wads and discuss chemical, technical, economical and legal aspects of a transition to the use of such products.

This study aimed to reveal the creative thinking of primary school female teachers in Al-Ahsa Governorate, in addition to identifying differences in light of the variables of experience and specialization. The researchers followed the descriptive method. The study was applied to a sample of (340) female teachers. The Creative Thinking Scale, which was adapted by researcher Hawzam Salman (2021), was used. The study concluded that the female teachers of primary stage in Al-Ahsa Governorate have creative thinking at a high degree; in addition, there were no differences in light of the variables of experience and specialization.

This paper presents the design and experimental results of a long cavity length Nd: YAG laser with large stable zone for water jet guided laser (WJGL) applications. The design is based on the light transmission matrix and resonator stability conditions, aiming to achieve a large stable zone and a short cut-off thermal focal length (CTFL). A folded concave resonator is researched to enhance the cavity length, and the influence of the tun-able cavity arm length on the oscillating beam in the resonator and in the YAG crystal is theoretically studied. Moreover, the effects of the output mirror curvature and the cavity arm length on the range of the stable area and the cut-off thermal focal length are also investigated. Experimental results show that a stable green laser output is obtained after second harmonic generation (SHG), with a pulse width ranging from 43ns to 143ns within the laser operating frequency range of 5-20kHz. At an operation frequency of 10kHz, the output power is 21.33W, and the instability of the output power within 400 minutes is 0.88%. The laser source achieves a maximum power of 25.7W at 20kHz, and the maximum single pulse energy reaches 2.7mJ at 6kHz. Finally, this is used as the laser source to couple with a water jet with a diameter of 100 microns, achieving a lossless water conductivity transmission over 60mm length with a peak power density of 0.742GW/cm2. These results demonstrate the suitability of the designed laser source for WJGL technology research.

In the present paper, we introduce the phytoscreening and antiradical characteristics of conker extracts prepared from 2-, 1-year stored and just collected plants as well as the anti-inflammatory effect of oinment composition based on the extract.

Despite being one of the most abundant elements in soil, phosphorus (P) often becomes a limiting macronutrient for plants due to its low bioavailability, primarily locked away in insoluble organic and inorganic forms. Phosphate solubilizing and mineralizing bacteria, also called phosphobacteria, isolated from P-deficient soils have emerged as a promising biofertilizer alternative, capable of converting these recalcitrant P forms into plant-available phosphates. Three such phosphobacteria strains - Serratia sp. RJAL6, Klebsiella sp. RCJ4, and Enterobacter sp. 198 - previously demonstrated their particular strength as plant growth promoters for wheat, ryegrass, or avocado under abiotic stresses and P deficiency. Comparative genomic analysis of their draft genomes revealed several genes encoding key functionalities, including alkaline phosphatases, isonitrile secondary metabolites, enterobactin biosynthesis and genes associated to the production of indole-3-acetic acid (IAA) and gluconic acid. Moreover, overall genome relatedness indexes (OGRIs) revealed substantial divergence between Serratia sp. RJAL6 and its closest phylogenetic neighbors, Serratia nematodiphila and Serratia bockelmanii. This compelling evidence suggests that RJAL6 merits classification as a novel species. This in silico genomic analysis provides vital insights into the plant growth-promoting capabilities and provenance of these promising PSRB strains. Notably, it paves the way for further characterization and potential application of the newly identified Serratia species as a powerful bioinoculant in future agricultural settings.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

This interdisciplinary investigation of the human remains of Balduin Helm, one of the most important abbots of Fürstenfeld monastery, provides novel information on that historic individual. This is particularly interesting since Balduin, during early 18th century, was involved in the renovation of this large Bavarian monastery. Metastatic prostate cancer was found as evidenced by multiple mixed osteolytic-osteoblastic bone lesions in all available vertebral bodies, fragments of both hemipelvises and isolated metastases in skull bones. Distribution, radio- and histomorphology, and especially the immunohistochemical detection of prostate-specific antigen in those metastases, definitively confirm this diagnosis. Further investigation, especially by stable isotope analysis, showed a balanced high-level diet with considerable contribution from animal protein and significant freshwater fish. These additional findings suggest a significant radiocarbon reservoir effect as an explanation for a “too old” radiocarbon dating. Finally, the obviously high-level protein diet may have contributed to the tumorigenesis which caused the death of the abbot at an advanced age.

Polyhydroxyalkanoates (PHA) are microbial biopolyesters utilized as “green plastics”. Their production under controlled conditions resorts to bioreactors operated in different modes. Because PHA biosynthesis constitutes a multiphase process, both feeding strategy and bioreactor operation mode need smart adaptation. Traditional PHA production setups based on batch, repeated batch, fed-batch or cyclic fed-batch processes are often limited in productivity, or display insufficient controllability of polyester composition. For highly diluted substrate streams like it is the case for (agro)industrial waste streams, fed-batch enhanced by cell recycling were recently reported as a viable tool to increase volumetric productivity. As emerging trend, continuous fermentation processes in single-, two-, and multi-stage setups are reported, which bring the kinetics of both microbial growth and PHA accumulation into agreement with process engineering, and allow tailoring PHA´s molecular structure. Moreover, we currently witness an increasing number of CO2-based PHA production processes using cyanobacteria; these light-driven processes resort to photobioreactors similar to those used for microalgae cultivation, and can be operated both discontinuously and continuously. This development goes in parallel to the emerging use of methane and syngas as an abundantly available gaseous substrates, which also calls for bioreactor systems with optimized gas transfer. The review sheds light on the challenges of diverse PHA production processes in different bioreactor types and operational regimes using miscellaneous microbial production strains such as extremophilic Archaea, chemoheterotrophic eubacteria and phototrophic cyanobacteria. Particular emphasize is dedicated to the limitations and promises of different bioreactor-strain combinations, and to efforts devoted to upscaling these processes to industrially relevant scales.

Systemic AL amyloidosis is a challenging disease for which many patients are considered frail in daily clinical practice. However, no study has so far addressed frailty and its impact on the outcome of these patients. We built a simple score to predict mortality based on three frailty-associated variables: age, ECOG performance status (&lt;2 vs. 2) and NT-proBNP (&lt;8500 vs. 8500 ng/L). Four-hundred and sixteen consecutive newly diagnosed patients diagnosed at ten sites from the Spanish Myeloma Group were eligible for the study. The score was developed in a derivation cohort from a referral center, and it was externally validated in a multicenter cohort. On multivariate analysis the three variables were independent predictors of survival. The score was able to discriminate four groups of patients in terms of overall survival and early mortality in both cohorts. Comorbidity was also analyzed with the Charlson comorbidity index, but it did not reach statistical significance in the model. A nomogram was created to easily estimate the mortality risk of each patient at each time point. This score is a simple, robust, and efficient approach to dynamically assess frailty-dependent mortality both at diagnosis and throughout the follow-up. The optimal treatment for frail AL amyloidosis patients remains to be determined but we suggest that the estimation of frailty-associated risk could complement current staging systems, adding value in clinical decision-making in this complex scenario.

The compatibility of graphene or graphene oxide with its dispersion medium (polymer) plays a critical role in the formation nanocomposite materials with significant property improvements. Environmentally friendly miniemulsion polymerization, which allows a formation of nanoencapsulation in an aqueous phase and high molecular weight polymer/composite production is one promising method. In this study, we screened a series of amphiphilic modifiers and found that the quaternary ammonium (ar-vinyl benzyl) trimethyl ammonium chloride (VBTAC) pending carbon double bonds could effectively modify the graphene oxide (GO) to be compatible with the organophilic monomer. After that, free radical miniemulsion polymerization could successfully synthesize stable latex of exfoliated poly (methyl methacrylate) (PMMA)/ GO nanocomposite. The final latex had an extended storage life and a relatively uniform particle size distribution. X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) analysis of this latex and its films indicated successful encapsulation of exfoliated nano-dimensional graphene oxide inside a polymer matrix.

In the present study, hypereutectic Al-Si alloy compacts and Al-Si/B4C composites were produced by conventional, microwave and spark plasma sintering techniques. The effects of sintering techniques and B4C particle addition on microstructural properties, density, hardness and electrical conductivity were investigated. The microstructures were examined with an optical microscope. Densities were measured using the Archimedes technique. Electrical resistance measurements were made with the four-point probe measurement technique. Elemental Al grains, master alloy grains and primary Si particles were determined in the microstructures of all samples. The addition of 15 wt% B4C caused the porosity rate to increase in the samples. Samples produced with SPS technique gave ≈80% higher hardness values than samples produced with CS and MWS. Compared to the samples produced with CS and MWS, the samples produced with SPS gave higher electrical conductivity values. Electrical conductivities were decreased as the weight percentage of B4C increased in all samples.

A detailed analysis of the dehydrogenation mechanism and reversibility of LiBH₄ doped by active Al* derived from AlH₃ was performed by thermogravimetry (TG), differential scanning calorimetry (DSC), mass spectral analysis (MS), powder X-ray diffraction (XRD), scanning electronic microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The results show that the dehydrogenation of LiBH₄/Al* is a five-step reaction: (1) LiBH₄ + Al → LiH + AlB₂ + “Li-Al-B-H” + B₂H₆ + H₂; (2) the decomposition of "Li-Al-B-H" compounds liberating H₂; (3) 2LiBH₄ + Al → 2LiH + AlB₂ + 3H₂; (4) LiBH₄ → LiH + B + 3/2H₂; (5) LiH + Al → LiAl + 1/2H₂. And the reversibility of LiBH₄/Al* composite is based on equation as follows: LiH + LiAl + AlB₂ + 7/2H₂ ↔ 2LiBH₄ + 2Al. The extent of dehydrogenation reaction between LiBH₄ and Al* greatly depends on the precipitation and growth of reaction products (LiH, AlB₂ and LiAl, etc.) on the surface of Al*. A passivation shell of Al* formed by these products is the kinetic barrier to the dehydrogenation of LiBH₄/Al* composite.

The Bacillus megaterium LVN01 species native to Colombia has demonstrated the ability to metabolize different co-products or industrial waste (such as fique juice, cane molasses, residual glycerol) and accumulate polyhydroxybutyrate (PHB), giving it potential in the bioplastics industry. In this research, the potential of liquid digestate as a carbon source for the production of PHA in fermentation processes with this bacterial strain was evaluated. Favorably, it was found that B. megaterium utilizes the nutrients from this residual substrate to multiply appropriately and efficiently synthesize poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV). Bench scale aerobic batch fermentation, under the operational conditions of this research [Volume: 3L; Temperature: 30.8°C; Agitation: 400 rpm; pH: 7.0 ± 0.2; Disolved Oxygen: 100% saturation; Antifoam 10% (v/v)], generated maximum values of DCW (0.56 g cell L-1) at 60 h, while the maximum PHB yield (360 mg PHB L-1) occurred at 16 h, which is very favorable for sustainable degradable bioplastics production. Additionally, GC-MS and NMR analyses confirmed that the PHBV copolymer synthesized by B. megaterium is made up of the monomers 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV). Furthermore, the thermal properties determined by TGA (Tonset=283.1 ºC, Tendset= 296.98 ºC. Td =290.114 °C) and DSC (Tm= ºC155.7 °C, ΔHf= 19.80 J g-1, Xcr = 18.17%), indicate that it is a thermally stable biopolymer with low percentages of crystallinity, providing flexibility that facilitates molding, adaptation, and application in various industrial sectors.

Ti-Al alloy phase layer/Ti-Al carburizing composite coating was prepared on the surface of titanium alloy by the stepwise coating method of hot dip aluminization and then carburizing. The weight gain results of the composite coating showed that the titanium alloy coated with the composite coating had long-term stability (≥16 days) at 800oC. The microstructure, phase structure and composition of the composite coating were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).The composite coating is composed of an alloy phase layer and a carburized layer. The natural transition of four phases (Ti3Al/TiAl/TiAl2/TiAl3) in the alloy phase layer, significantly improves the interfacial bonding between the coating and the substrate, and slows down the propagation of microcracks through the coating.Al2O3, TiC and C in the carburizing layer improve the surface hardness of the coating, and TiAl2 and Al2O3 also have excellent oxidation resistance at high temperature.

Reading is a complex cognitive task involving processes from different systems. The present work aims to identify some points of divergence reported in the reading literature and discuss them in a new experimental paradigm framework. Inspired by the paradigms of perceptual identification and rapid parallel presentation (RPVP), we emphasize that the originality of our experimental paradigm lies in the recruitment of multi-stable Arabic percepts within the region where low-level processing occurs (i.e., the visual span area). With good flexibility, the current paradigm has reached higher-order processing levels. In agreement with previous works highlighting the parafoveal-on-foveal effect, results suggest parallel word processing. Furthermore, they suggest a rapid extraction of syntactic and semantic information from words in sentences while attributing an advantage to semantic processing in the emergence of the sentence superiority effect.

Relations between nutrient assimilation and growth rate in fishes may vary with abiotic factors such as temperature. The effects of feeding status, ontogeny and temperature regimes (15, 18 and 21 °C) on stable isotope (δ13C and δ15N) patterns were assayed and modelled in juveniles of the seahorse Hippocampus guttulatus. The use of effective day degrees (D°eff) and chronological time (age) were compared as development progress indices. Newborn seahorses were maintained at three temperature levels both deprived of food (5 days) or fed (30 days) on copepods or/and Artemia. Isotopic signatures in fed seahorses clearly differed from those in unfed juveniles. Temperature had a significant effect on δ13C values in fed juveniles throughout the experimental period. δ15N values also varied significantly with age, but not with temperature level. Faster growth and food assimilation in seahorses held at 18 and 21 °C were supported by faster variations in isotopic values. Our findings demonstrate that effective day degrees should be preferred over chronological time as index of developmental progress in temperature fluctuating scenarios or for comparative studies.

Isotopic stable analysis (SIA) is a powerful tool in the assessment of different types of ecological and physiological studies. For that, different preservative methods for the samples are commonly used prior to isotopic analysis. The effects of various preservative methods (drying, freezing, ethanol and formaldehyde) have been analyzed for C:N ratio, δ13C and δ15N on a variety of tissues including dorsal fins (three seahorse and two pipefish species), seahorse newborns (three seahorses species), and prey (copepods and different stages of Artemia) commonly used to feed the fishes in rearing conditions. The aims of the study were to: (i) evaluate isotopic effects of preservation methods across tissues; and (ii) construct the first conversion models available in syngnathid fishes. The preservation in ethanol and to a lesser extend in formaldehyde significantly affected δ13C values, whereas δ15N signatures were not affected significantly. Due to their low lipid content, the isotopic signals in fish fins were almost unaffected, supporting the suitability of dorsal fins as a convenient tool in isotopic studies on vulnerable species such as syngnathids. The regression equations provided permit the successful conversion of δ13C and δ15N values between preservative treatments. The conversion models can be applied to isotopic studies in the field and in the laboratory.

Water resources management is one of the most important challenges worldwide because water represents a vital resource for sustaining life and environment. In the aim of sustainable groundwater management, the identification of aquifer recharge areas is a useful tool for water resources protection. In a well-developed karst aquifer, environmental isotopes provide support for identifying aquifer recharge areas, residence time and interconnections between aquifer systems. This study deals the use of environmental isotopes to identify the main recharge area of a karst aquifer in the Upper Valley of Aniene River (Central Italy). The analysis of 18O/16O and 2H/H values and their spatial distribution in the aquifer, make it possible to trace back groundwater recharge areas based on average isotope elevations. The Inverse Hydrogeological Balance Method was used to validate spring recharge elevations obtained by the use of stable isotopes. Areas impacted by direct and rapid rainfall recharge into the study area were delineated, showing groundwater flowpaths from the boundaries to the core of the aquifer. The results of this study demonstrate the contribution that spatial and temporal isotope changes can provide to the identification of groundwater flowpaths in a karst basin, taking into account the hydrogeological setting

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

Growing interest has accrued in the co-existence of cardiac amyloidosis and valvular heart disease. Amyloid infiltration from either transthyretin (ATTR) or light chain (AL) origin may affect any structure of the heart, including the valves. Recent literature has mainly focused on aortic stenosis and cardiac amyloidosis, improving our understanding of epidemiology, diagnosis, treatment and prognosis of this dual pathology. Even though of high clinical relevance, data on mitral/tricuspid regurgitation and cardiac amyloidosis is rather scarce and mostly limited to case reports and small cases series. It is the aim of this review article to summarize the current evidence of concomitant valvular heart disease and cardiac amyloidosis including epidemiology, diagnostic approaches, screening possibilities, therapeutic management, and prognostic implications.

Understanding the infiltration and solidification processes of liquid 5083Al alloy into Al2O3 three-dimensional reticulated porous ceramic (Al2O3(3D) RPC) is essential for optimizing the microstructure and properties of Al2O3(3D)/5083Al interpenetrating phase composites (IPCs) prepared by low-pressure infiltration process (LPIP). This study employs ProCAST software to simulate the infiltration and solidification processes of liquid 5083Al with pouring velocities (PV) of 0.4 m/s infiltrating into Al2O3(3D) RPC preforms with varying porosities at different pouring temperatures (PT) to prepare Al2O3(3D)/5083Al IPCs using LPIP. The results demonstrate that pore diameter of Al2O3(3D) RPC preforms and PT of liquid 5083Al significantly influence the of the infiltration. Solidification process analysis reveals that the Al2O3(3D) RPC preform with smaller pore diameters allows the lower pouring velocity of 5083Al to solidify faster compared to the preform with larger pore diameters. Al2O3(3D)/5083Al IPCs were prepared successfully from Al2O3(3D) RPC porosity of 15 PPI with liquid 5083Al at PV 0.4 m/s and PT 800 °C using LPIP, resulting in nearly fully dense composites, where both Al2O3(3D) RPCs and 5083Al interpenetrate throughout the microstructure. The infiltration and solidification defects were reduced under air pressure of 0.3 MPa (corresponding to PV of 0.4 m/s) during LPIP. Finite volume method simulations are in good agreement with experimental data, validating the suitability of the simplified model for Al2O3(3D) RPCs in the infiltration simulation.

We investigate the ammonium removal abilities of natural and synthetic zeolites, which have distinct Si/Al ratios and various surface areas, to study how adsorption and ion-exchange processes in zeolites perform under different ammonium concentrations and different temperatures. Five zeolites including natural mordenite, chabazite, erionite, clinoptilolite and synthetic merlinoite were immersed in 20 mg/kg, 50 mg/kg and 100 mg/kg ammonium solutions. The results demonstrate that zeolites under high ammonium concentrations (100 mg/kg) possess higher physical adsorption capacity (0.398–0.468 meq/g), whereas those under lower ammonium concentrations (20 mg/kg) possess greater ion-exchange property (64–99%). The ion-exchange ability of zeolites are extremely dependent on the cation content of the zeolites, and the cation content is affected by the Si/Al ratio. The surface area of zeolites also has a partial influence on its physical adsorption ability. When the surface area is less than 100 m²/g, the adsorption ability of zeolite increases obviously with surface area; however, adsorption ability is saturated as the surface area becomes larger than this critical value of 100 m²/g. When we carried out the zeolites in 50 mg/kg ammonium concentration at different temperatures (5~50 ℃), we found that zeolites exhibit the highest ammonium removal ability at 30°C and the potassium release was enhanced at 30~40 ℃.

Films prepared from poly(3-hydroxybutyrate-co-4-hydroxybutyrate) copolymers produced by Aneurinibacillus sp. H1 using an automatic film applicator were homogeneous and had a defined thickness, which allowed a detailed study of physicochemical properties. Their properties were compared with a poly (3-hydroxybutyrate) homopolymer film prepared by the same procedure, which proved to be significantly more crystalline by DSC and XRD. Structural differences between samples had a major impact on their properties. With increasing 4-hydroxybutyrate content, the ductility and release rate of the model hydrophilic active ingredient increased significantly. Other observed properties, such as the release of the hydrophobic active substance, the contact angle with water and ethylene glycol, or the surface morphology and roughness, were also affected by the composition. The identified properties predetermine these copolymers for wide use in areas such as biomedicine or smart biodegradable packaging for food or cosmetics. The big advantage is the possibility of fine-tuning properties simply by changing the fermentation conditions.

In the present research, groups of nanolayered structures and nanohybrids based on organic green dyes and inorganic species are designated to act as fillers for PVA for inducing new optical sites and increasing its thermal stability through producing polymeric nanocomposites. In this trend, different percentages of Naphthol green B were intercalated as pillars inside the Zn-Al nanolayered structures to form green organic-inorganic nanohybrids. The two-dimensional green nanohybrids were identified by X-ray diffraction, TEM and SEM. According to the thermal analyses, the nanohybrid, which has the highest amount of green dyes, was used for modifying the PVA through two series. In the first series, three nanocomposites were prepared depending on the green nanohybrid as prepared. In the second series, the yellow nanohybrid, which was produced from the green nanohybrid by thermal treatment, was used to produce another three nanocomposites. The optical properties revealed that the polymeric nanocomposites depending on green nanohybrids became optical-active in UV and visible regions because the energy band gap decreased to be 2.2 eV. In addition, the energy band gap of the nanocomposites depended on yellow nanohybrids was 2.5 eV. The thermal analyses indicated that the polymeric nanocomposites are thermally more stable than that of the original PVA. Finally, the dual functionality of organic-inorganic nanohybrids that produced from the confinement of organic dyes and the thermal stability of inorganic species converted the non-optical PVA to optical-active polymer in a wide range with high thermal stability

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

Beaches are among the habitats most frequented by migratory birds for breeding and/or wintering. However, threats such as human pressure and sea level rise can reduce the availability of these habitats for different species. The presence of alternative areas, such as salt pans and brackish habitats, is essential for many migratory shorebird populations. This study addresses the post-breeding dispersal of the Kentish plover (Charadrius alexandrinus) in the Iberian Peninsula by analysing C and N isotopes in feathers. The study was conducted at six locations along the Iberian coast, which were categorized in three areas: NW Atlantic coast, the Atlantic coast of Andalusia and the Mediterranean coast. Although linear mixed models did not reveal any significant effects of sex or coastal area on isotopic levels, the variability in the data suggests different habitat-use strategies in the post-reproductive period. Birds from the northwest of the Iberian Peninsula exhibit greater fidelity to a single habitat type, i.e. coastal beaches, while populations from the Mediterranean coast and the Atlantic coast of Andalusia show different individual dispersal strategies, occupying coastal habitats and freshwater wetlands. The lack of alternative habitats for the northwest Iberian population, the reduction in available habitat due to rising sea levels and human pressure together pose a serious threat to the survival of this species, already with an unfavourable conservation status.

New ideas on the framework of Neutrosophic SuperHyperGraph for different styles of Neutrosophic SuperHyper-Wheel and Neutrosophic SuperHyper-Star are introduced. More instances and more clarifications alongside sufficient references are featured with a specific type of independency of SuperHyperVertices.

The illegal wildlife trade is a significant threat to global biodiversity, often targeting already threatened species. In combating the trade, it is critical to know the provenance of the traded animal or part, to facilitate targeted conservation actions, such as education and enforcement. Here we present and compare two methods, portable X-ray fluorescence (pXRF) and stable isotope analysis (SIA), to determine both the geographic and source provenance (captive or wild) of traded animals and their parts. Using three critically endangered, frequently illegally traded Philippine species, the Palawan forest turtle (Siebenrockiella leytensis), the Philippine cockatoo (Cacatua haematuropygia), and the Philippine pangolin (Manis culionensisis) we demonstrate that using these methods we can more accurately assign provenance using pXRF data (x ̅ = 83%), than SIA data (x ̅ = 47%). Our results indicate that these methods provide a valuable forensic tool that can be used in combating the illegal wildlife trade.

Chemical safety is related to public health, safety and environmental concerns, and the dangerous chemicals safety problem is becoming the one that people commonly pay attention to. Strengthening chemical safety supervision not only involves safe production, but also is an important link to maintain social safety. Most related studies focus on chemical safety under normal regulation, this paper addresses the perspective of ‘special rectification’ and ‘normal regulation’, and establishes an evolutionary game model between chemical enterprises and government supervision departments under different supervision modes. Based on the evolutionary game theory, this paper studies the evolution process of the two game players' strategy choices, and compares and analyzes the evolution, stability and equilibrium between the chemical safety and the behavior strategies of government regulatory departments. The model is effectively analyzed based on numerical simulation, and the results show that: Under the ‘special rectification’ mode, the strategic choice of chemical enterprises engaging in safety without investment depends on the difference between the benefits and costs of safety without investment; In the ‘normal regulation’ mode, the choice of its safety non-investment strategy depends on the difference between the cost of engaging in safety investment and the cost of safety non-investment; Increasing the government's punishment will encourage chemical enterprises to take safety investment behavior under the two supervision modes. Increasing the punishment has a significant impact on the safety investment behavior of chemical enterprises under the ‘normal regulation’ mode, but it has no significant impact on the behavior of chemical enterprises under the ‘special rectification’ mode. At the same time, increasing the punishment will inhibit the strict supervision behavior of the government. The research conclusion provides important decision support for government departments to effectively supervise the safety production of chemical enterprises.

Variations in geochemical signatures of fossil brachiopod shells may be due to diagenesis and/or biological processes (i.e. ‘vital effects’). Characterize them is crucial to identify reliable areas into the shell suitable to paleoclimatological studies. This investigation contributes to an in-depth understanding of geochemical variations of Gigantoproductus sp. shells (SW Spain, Serpukhovian age), which could affect to the Late Paleozoic Ice Age interpretation. Microstructural, crystallographic, cathodoluminescence and geochemical (minor and trace elements, δ18O, δ13C, and strontium isotopes) characterisation have been performed on the tertiary layer of the ventral valve, to assess the preservation state. Poorly-preserved areas exhibit microstructural and geochemical changes such as recrystallisation, fracturing and higher Mn and Fe enrichment. Moreover, these areas have higher dispersion of ⁸⁶Sr, ⁸⁷Sr, δ18O and δ13C than well-preserved areas. Three structural regions have been identified in well-preserved areas of ventral valve by differences in valve curvature and thickness, such as the umbonal, thick and thin regions. These regions have different proportions of Mg, S, Na, δ18O, and δ13C, whom are interpreted as ‘vital effects’ and probably are related with growth rate differences during shell growth. Gigantoproductus tertiary layer seems the best suitable to paleoclimatological studies because it retains the original microstructure and geochemistry.

The initial development of seahorse juveniles is characterized by low digestion capabilities. Stable isotope analysis is an effective tool in studies of trophic food webs and animal feeding patterns. The present study provides new insights for the understanding of growth and food assimilation in early developing seahorses following a laboratory diet switch. The study was performed in early life stages of the seahorse Hippocampus reidi by assessing the influence of diet shift on changes and turnovers in carbon (δ13C) and nitrogen (δ15N) stable isotope in juveniles. Newborn seahorses were fed for 60 days following two feeding schedules (A6 and A11) based initially on copepods Acartia tonsa and subsequently on Artemia nauplii (since days 6 and 11, respectively). After prey shift, we determined δ13C and δ15N turnover rates as functions of change in either body mass (fitting model G) and days of development (fitting model D), contributions of metabolism and growth to those turnover rates, and diet-tissue discrimination factors. Survival, final dry weight and final standard length for diet A11 were higher compared to diet A6. The shift from copepods to Artemia lead to fast initial enrichments in δ13C and δ15N. Afterwards, the enrichment was gradually reduced until reaching the isotopic equilibrium with diet. In most cases, both fitting models performed similarly. The isotopic analysis revealed that 100% of tissue turnover was attributed to growth in diet A11, whereas 19-25% was endorsed to metabolism in diet A6. Diet-tissue discrimination factors were estimated for the first time in seahorse juveniles, resulting in higher estimates for diet A11 (2.9 ± 0.7‰ for δ13C; 2.5 ± 0.2‰ for δ15N) than in diet A6 (1.8 ± 0.1‰ for δ13C; 1.9 ± 0.1‰ for δ15N). This study highlights the relevance of feeding on copepods and their effect on isotopic patterns and discrimination factors in seahorse juveniles after a dietary shift. Regarding the application of the results achieved to feeding schedules in the rearing of H. reidi, a long period of feeding on copepods during the first days of development is highly recommended.

Cesiumtrifluoroacetate (CsTFA) is a key chemical for RNA-based stable isotope analyses to link the structure and function of microbial communities. We report a protocol to easily synthesize CsTFA from Cesiumcarbonate (Cs₂CO₃₎ and Trifluoroacetate (TFA) and show that self-synthesized CsTFA behaves similar to commercial CsTFA in the separation of isotopically labelled and unlabelled E. coli RNA.

The liver is a key node of whole-body nutrient and fuel metabolism and is also the principal site for detoxification of xenobiotic compounds. As such, hepatic metabolite concentrations and/or turnover rates inform the status of both hepatic and systemic metabolic diseases as well as the disposition of medications. As a tool to better understand liver metabolism in these settings, in vivo magnetic resonance spectroscopy (MRS) offers a non-invasive means of monitoring hepatic metabolic activity in real time both by direct observation of concentrations and dynamics of specific metabolites as well as by observation of their enrichment by stable isotope tracers. This review summarizes the applications and advances in human liver metabolic studies by in vivo MRS over the past 35 years and discusses future directions and opportunities that will be opened by the development of ultra-high field MR systems and by hyperpolarized stable isotope tracers.

Little in the scholarly economics literature is directed specifically to the performance of sta­ble value funds, although they occupy a leading place among retirement investment vehicles. They are currently offered in more than one-third of all defined contribution plans in the USA, with more than $800 billion of assets under management. This paper rigorously ex­amines their performance throughout the entire period since their inception in 1973. We produce a composite index of stable value returns. We next conduct mean-variance analysis, Sharpe and Sortino ratio analysis, stochastic dominance analysis, and optimal multi-period portfolio composition analysis. Our evidence suggests that stable value funds dominate (on average) two major asset classes based on a historical analysis, and that they often occupy a significant position in optimized portfolios across a broad range of risk aversion levels. We discuss factors that contributed to stable value funds’ past performance and whether they can continue to perform well into the future. We also discuss considerations regarding whether or not to include stable value as an element in target date funds within defined con­tribution pension plans.

Egyptians face a significant challenge in meeting the growing population's water needs for agriculture and food production. To address this, policymakers and researchers have implemented the National Great Project for Lining and Rehabilitation of All Open Canals of the Irrigation Network to reduce irrigation water losses through seepage, evaporation, and evapotranspiration. The current field study evaluates water losses from the Al Maanna canal network in Assiut governorate, Middle Egypt, using empirical formulas and field ponding methods. The obtained results indicated that the Moleth-Worth formula is more compatible and gives results that are in good agreement with the field measurements carried out. The estimated seepage losses from the existing, distorted Al Maanna canal network using the Moleth-Worth formula and field ponding method were about 2.07 and 2.20 million m3/month, respectively. Also, the calculated maximum evaporation and evapotranspiration losses were about 0.086 and 1.133 million m3/month, respectively. Consequently, the total water losses might be about 3.42 million m3/month, representing nearly 13.63% of the Al Maanna canal’s total discharge. After completing the lining process, seepage losses from lined canals were determined to be only about 0.472 million m3/month using the ponding method, while evaporation and evapotranspiration losses will be significantly decreased after canal rehabilitation. Hence, lining the Al Maanna canal network can decrease the total water losses by about 84%, which is sufficient to recommend and encourage the lining processes where the value of the gained quantities of water exceeds all the implementation expenses, in addition to other moral, cultural, and environmental gains.

The conductor aluminum alloys Al-0.25wt.%Zr doped additionally with Х = Er, Si, Hf, and Nb were the objects of investigations. The fine-grained microstructure in the alloys was formed by Equal Channel Angular Pressing and Rotary Swaging. The thermal stability of the microstructure, specific electrical resistivity, and microhardness of the novel conductor aluminum alloys was investigated. The mechanisms of nucleation of the Al3(Zr,X) secondary particles during annealing the fine-grained aluminum alloys were determined using Jones-Mehl-Avrami-Kolmogorov equation. Using Zener equation, the dependencies of the mean secondary particle sizes on the annealing time were obtained on the base of analysis of the data on the grain growth in the aluminum alloys. The secondary particle nucleation during long-time low-temperature annealing (300 оC, 1000 hrs) was shown to go preferentially at the cores of the lattice dislocations. The Al-0.25%Zr-0.25%Er-0.20%Hf-0.15%Si alloy subjected to long-time annealing at 300 оC has the optimal combination of the microhardness and electrical conductivity (59.8%IACS, Hv = 480 ± 15 MPa).

Nano Silicon carbide reinforced aluminum (Al/nanoSiC) metal matrix composites are attractive because of their superior properties such as high strength and stiffness, Application of aluminum in technological and structural application is growing steadily. The major limitation for metal matrix nano composites, however, is their propensity to brittle fracture. The new technologies and new materials are two basic aims for companies. In this research, the effect of addition Al/SiC nano particles on microstructure and mechanical properties of pure aluminum has been investigated. Pure aluminum powder and various fractions of SiC particles with an average diameter of 50 nm were milled by a high-energy planetary ball mill to produce nanocrystalline Al–SiC nanocomposite powders. Pressing and sintering applied to consolidate powders to tablet shape. Then the samples were rolled to cylindrical shape. The nano SiC Percentage were 0%, 2.5%, 5%, 7.5%, 10% , 12,5% and 15%. Mechanical tests such as tensile, hardness, fracture toughness and young’s modules measurement carried out to study the mechanical behavior of each alloy. Scanning electron microscopy was used to study the morphology and microstructure of nanocomposite powders and bulk samples. The role of wt% fraction of SiC nanoparticles was investigated. The results shows that the addition of SiC nano particles has significant influence on the microstructure and mechanical properties of composites and usually the optimum properties depends on wt% SiC.

Accurate, detailed and recent Information about land cover/use is important and much more needed for different aspects of sustainable development and environmental management. As remote sensing datasets are becomes one of the most important and effective tools to generate such information, this study aimed to generating land cover map for sub area in Al-Ahasaa Oasis, Saudi Arabia, by using and classifying a subset of Landsat-ETM+ image of the selected study area, as bases and required input for future studies and researches. Different image preprocessing techniques in addition to a will-known and widely used classification method (i.e., Maximum Likelihood classifier) were applied. To be reliable with the final product, accuracy assessment was carried out with 89% agreement and accepted according to the applied method. Different land cover classes were found in the study area, which includes (Sand dunes, Water bodies, Sabakha, Bare soil, Urban, and Agricultural lands). The study also revealed that the dominant land cover class is sand dunes with approximately ± 70% in area. The study strongly indicated that the area has long been affected by sand movement. Finally, the study suggested that, further researches with more advanced methods rather than traditional methods are needed in the future to support the findings of this study, with high degree of accuracy.

Compound-specific isotope analysis (CSIA) can provide unique insights into the cycling of elements including carbon and nitrogen. One approach for CSIA is the use of high-performance liquid chromatography (HPLC) to separate compounds of interest, followed by analysis of these compounds using an elemental analyzer coupled to an isotope ratio mass spectrometer. A key component of this technique is the fraction collector, which automatically collects compounds as they are separated by HPLC. Here we present a fraction collector which is a simple adaptation of a 3D printer, and thus can be easily adopted by any laboratory already equipped for HPLC. In addition to the much lower cost compared to commercial alternatives, this adaptation has the advantage for CSIA that the 3D-printer is able to heat the collected fractions, which is not true for many commercial fraction collectors. Heating allows faster evaporation of the solvent, so that the dried compounds can be measured by EA-IRMS immediately. The procedure can be repeated consecutively so that dilute solutions can have the compounds concentrated for analysis. Any computer-controlled HPLC can be integrated to the fraction collector used here by means of AutoIt.

The purpose of this study was to elucidate patterns and mechanisms driving seasonal and inter-annual variations of carbon and nitrogen stable isotopes in the zooplankton crustacean commu-nity of Lake Maggiore (Italy), during the period 2009-2020. Different zooplankton taxa and groups revealed different ranges of d13C signatures, giving an insight into food sources and niche partition. In particular, cyclopoids had a restricted range with most negative d13C‰ values and increase in d13C fractionation with the establishment of water thermal vertical stratification, high-lighting the importance of vertical distribution as key factor for taxa coexistence in a vertically heterogenous environment. d13C of the zooplankton community and of Daphnia were positively related to water temperature (R2=0.58 p <0.0001 and R2=0.68 p <0.0001, respectively) and d13C Daphnia signature to chlorophyll-a (R2=0.32, p < 0.0001). Decomposition of time series data for zooplankton carbon and nitrogen signatures and environmental parameters identified increasing trends in water temperature, chlorophyll-a and water conductivity and decrease in nitrate, that matched changes in carbon isotopic signature trend in some zooplankton taxa (Bosmina, Daphnia and diaptomids). Overall, the observed patterns in zooplankton isotopic signatures were interpreted as integrations of climate warming effects in Lake Maggiore, affecting both food sources availability and environmental conditions.

The challenge of achieving ultrafast switching of electric polarization in ferroelectric materials remains unsolved, as there is no experimental evidence of such switching to date. In this study, we have developed an enhanced model that describes switching within a two-dimensional space of generalized coordinates. Our findings indicate that stable switching in barium titanate cannot be achieved through a single linearly polarized pulse. When the intensity of the linearly polarized pulse reaches a certain threshold, the sample experiences depolarization, but not stable switching. Our study also reveals that phonon friction plays a minor role in the switching dynamics and provides an estimate of the optimal parameters of the perturbing pulse with the lowest intensity that results in depolarization of an initially depolarized sample.

We examined PT parameters, geochemical peculiarities, and fluid sources of the Ulug-Sair ore occurrence attributable to class of intrusion-related gold deposits and according to ore mineral assemblages corresponding to Au-Bi type with wide Bi minerals (AgBiTe, Bi2Te2Se, Cu3,07BiS3, Bi), tellurides (Au and Ag), Se-tellurides (Ag and Bi), and selenides (Au, Ag, and Hg). We identified that ‘pre-gold’ quartz-tourmaline veins were deposited using an aqueous Mg-Na-K-chloride fluid with a salinity of 8–10 wt % NaCl eq. At 325–370 °C; host breasts were formed due to a CO2-water fluid containing CH4 and N2, with a salinity of 0,18–6,1 wt % NaCl eq. at least 200–400 °C. Gold-bearing mineral assemblages were formed at P ~ 0,75–1,0 kbar (~ 2,3–3 km) due to CO2-water chloride (Na-K±Fe, Mg) fluid with CH4, Na2SO4, and Na2B2O5, and salinities 1,7–12,5 wt % NaCl eq. during the decreasing temperatures from 360 up to 115 °C (gold-sulfide-quartz veins – 360–130 °С, and gold-telluride-sulfide-quartz veins – 330–115 °C) and variations fO2, fS2, fSe2, and fTe2. The isotopic composition of δ34SH2S fluid (-0,7…+2,5 ‰) indicates the juvenile or magmatic origin of fluid and ore elements. The δ34OH2O fluid indicates that, at an early substage, the formation of ore occurrence involved a fluid of magmatic or metamorphic origin (+7,3…+11,4 ‰), and, in the later substage, it mixed with meteoric waters (-2,3…+9,1 ‰).

Zagros is an important region with high quality and quantity karstic water resources in the Middle East. This region provides a dominant part of potable and agricultural water needs for its inhabitants as well as agricultural water needs for nearby regions. Therefore, studying karstic water resources in Zagros by accurate methods such as stable isotopes techniques is very important. In this investigation, hydrological characteristics of groundwater resources including groundwater origin, recharge rate and recharge elevation have been studied using stable isotopes (¹⁸O and ²H). The results show that stable isotopes signatures in groundwater resources show notable variations across Zagros and groundwater resource mainly plot on south and west Zagros meteoric water lines. In addition, recharge elevation and recharge rate in groundwater resources also show significant variations in Zagros. Finally, the stable isotopes signatures in precipitation and groundwater has been used to study the role of each dominant air mass (contribution percentage of precipitation events originate from each air mass) in groundwater resources recharge using Simmr package in R language. Overall, groundwater resources in Zagros is recharged by precipitation events originate from various air masses and they have various recharge rates and recharge elevations.

Nested structure is a structural feature that is conducive to system stability formed by the co-evolution of species in mutualistic ecosystems, and reflects the ability of ecosystem stability to be restored to a stable state again after being destroyed. The co-opetition relationship and value flow between industrial sectors in the global value chain are similar to the mutualistic ecosystem, and the pattern of the global economic system is always changing in dynamic equilibrium. Nestedness theory is used in this article to define the generalist and specialist sectors in the global value chain to analyze the changes in the global supply pattern. Then we study the mechanism of the global economic system to reach a stable equilibrium and the role of different sectors in the steady of the economic system, so as to provide countermeasures for enhancing the stability of the global economic system. At the end of the article, the domestic trade network, export trade network and import trade network of each country are extracted, and an econometric model is designed to analyze how the microstructure of the production system affects a country’s macroeconomic performance, thereby deriving the conclusion that the stability of the international trade network is crucial to a country's economic development.

In order to obtain stable super-hydrophobicity, suitable hydrophobic treatment agent should be selected according to different materials. In this paper, cotton and poly (-ethylene terephthalate) (PET) fabric was respectively coated by dodecyl methacrylate (LMA) via argon combined capacitively coupled plasma (CCP), and the surface hydrophobicity and durability of treated cotton and polyester fabrics were also discussed. An interesting phenomenon was happened that LMA coated cotton fabric (Cotton-g-LMA) had better water repellency and mechanical durability than LMA coated PET fabric (PET-g-LMA), and LMA coated hydroxyl grafted PET fabrics (PET fabrics were successively coated with polyethylene glycol (PEG) and LMA, PET-g-PEG&amp;LMA) had similar performance to those of cotton fabrics. The water contact angle (WCA) of Cotton-g-LMA, PET-g-LMA and PET-g-PEG&amp;LMA was 156 °, 153 ° and 155 °, respectively, and after 45 washing cycles or 1000 rubbing cycles, the corresponding WCA was decreased to 145 °, 88 °, 134 °and 146 °, 127 °, 143 °, respectively. Also, thermoplastic polyurethane (TPU) and polyamides-6 (PA6) fabrics were all exhibited the same properties to PET fabric. Therefore, the grafting of hydroxyl can improve the hydrophobic effect of LMA coating and the binding property between LMA and fabrics effectively without changing the wearing comfort..

There are numerous yeast species related to wine making, particularly non-Saccharomyces, that deserve special attention due to the great potential they have when it comes to making certain changes in the composition of the wine. Among them, Schizosaccharomyces pombe stands out for its particular metabolism that gives it certain abilities such as regulating the acidity of wine through maloalcoholic fermentation. In addition, this species is characterized by favouring the formation of stable pigments in the wine and releasing large quantities of polysaccharides during ageing on lees. Moreover, its urease activity and its competition for malic acid with lactic acid bacteria make it a safety tool by limiting the formation of ethyl carbamate and biogenic amines in wine. However, it also has certain disadvantages such as its low fermentation speed or the development of undesirable flavours and aromas. In this chapter, the main oenological uses of Schizosaccharomyces pombe that have been proposed in the last years will be reviewed and discussed.

Background: Coronary tortuosity is a common angiographic finding. Scarce data is available on clinical profile of patients with coronary tortuosity (CT) and its relation with coronary artery disease (CAD). Method: A total 224 patients undergoing angiography for suspected CAD were included in the study. CT was defined by the presence of ≥3 consecutive bends of > 45 degree measured at end-diastole in an epicardial artery ≥2 mm in diameter. CT was present in 45(20.08%) patients in the study and another 45 patients without CT was randomly selected as control (NCT group). Clinical profile of CT and NCT group was compared. Results: Incidence of CT was significantly higher in females (p=0.000) and hypertensives (p=0.001) patients. CT was most commonly seen in Left circumflex coronary artery. Incidence of CAD was significantly lower in CT group as compare to NCT group (0.02). Risk factors for CAD was associated with reduced incidence of CT. Majority (88.46%) patient with CT without CAD presented with chronic stable angina out of which (65.21%) had an objective evidence of myocardial ischemia. Conclusion: CT is more commonly seen females and hypertensive patients. It has negative correlation with CAD. Risk factors of CAD do not predict CT. CT itself can lead to myocardial ischemia.

The principal main of this research work was the study the influence of Cu addition on the wear behavior (WB) of eutectic Al-12.6Si alloy developed by spray forming (SF) method and compared with as-cast (AC) alloys. The phases of chemical compositions and microstructure were studied by optical microscopy, energy dispersive spectroscopy (EDS) and Scanning Electron Microscopy (SEM). The microstructure of SFAl-12.6Si (SF1) alloy reside — of fine primary and eutectic Si phases evenly distributed in the equiaxed α-Al matrix and SF Al-12.6Si-2Cu (SF2) alloy lie of uniformly distributed fine eutectic Si particulates and spherical form θ-Al2Cu precipitates in α-Al matrix. On other hand, the AC Al-12.6Si alloy (AC1) alloy involve of eutectic Si needles in the dendrite α-Al matrix, whereas AC Al-12.6Si-2Cu (AC2) alloy consisted of eutectic Si needles and Chinese script form θ phase distributed randomly in the α-Al matrix. The microhardness and wear properties were analyzed using Vickers hardness (VH) and dry sliding WT. The SF alloys exhibit superior hardness compared to the AC alloys. The wear properties of SF alloys exhibited significantly superior compared to the AC alloys. The SF2 alloy showed high wear resistance (WR) than the SF1 alloy in the entire sliding velocities and applied loads. The results indicate that the spray deposited alloys have a lower coefficient of friction (CF(µ)) than the AC alloys under varying load and sliding velocity conditions. The high WR in the SF alloy was due to microstructural modification during SF and precipitation of fine Al2Cu intermetallic and solid solubility effects. The SF2 depicts increased transition from oxidative to abrasive. In other ways, AC alloys demonstrate wear mechanisms that change from oxidative to abrasive and delamination with an increase in sliding velocity and load.

In this study, Cu/Ni and Cu/Al multilayer thin films with individual layer thickness varying from 25 nm to 200 nm were deposited at room temperature and further annealed up to 300 ℃. The mechanical and microstructural properties of the multilayers were characterized by nanoindentation, x-ray diffraction, and scanning electron microscopy. Both systems exhibited an increase in hardness with increasing annealing temperature. However, the Cu/Ni system showed a gradual and moderate (up to 30%) hardness increase from room temperature to 300 ℃, while the Cu/Al system showed a sharp increase (~150%) between 125℃ and 200℃. This distinct strengthening behavior is attributed to solid solution formation in Cu/Ni and diffusion-activated intermetallic formation in Cu/Al.

The development of Al-Ni alloys with a controlled microstructure has had a great impact on the field of study of aluminum-based alloys. In the present research, the influence of thermal parameters on the grain structures resulting from the directional solidification process of Al-Ni alloys with different alloy content has been studied. It has also been evaluated how different structures and the distribution of second phases influence the corrosion behavior and microhardness of alloys. The columnar-to-equiaxed transition (CET) was observed to occur when the temperature gradient in the melt decreased to values between 1.3 to 2.9 ° C/cm. In addition, a small increase in the microhardness values was observed as a function of the Ni-content. When the Ni-content increase, the resistance to polarization decreases for samples with equiaxed grain structure, throughout the range of compositions studied. Furthermore, the equiaxed grain structure presents higher resistance to polarization values than the columnar grain zone, for alloys with a composition equal to or lower than the eutectic composition.

Enterobacteriaceae can contaminate meat during various stages of processing, including slaughter, evisceration, and butchering, causing foodborne illnesses. The purpose of the study was to investigate the prevalence of Enterobacteriaceae associated with carcasses obtained from slaughterhouses and raw cut meat collected from butcher shops. A total of 120 samples of camels and cattle were identified using biochemistry and PCR testing. Total viable count (TVC) was range from 4.91 to 5.37 Log10 CFU/g in slaughterhouses and butcher shops. E. coli was predominating with 84 (70%) among all samples, where the camels had the highest with 100% and sheep the lowest with 30%. Salmonella spp. was confirmed in 40% of camel samples, 47.5% of cattle samples, and 32.5% in sheep samples. Twenty-five Enterobacteriaceae genera were confirmed using PCR. Where sheep’s samples had the highest occurrence of Enterobacteriaceae with 15 different genera followed by camels and cattle samples with 14 different genera. The prevalence of Enterobacteriaceae among camel, cattle, and sheep carcasses raises significant concerns regarding food safety. Adherence to good hygiene practices throughout animal slaughtering is crucial to minimize the risk of infection and transmission and ensure food safety.

Thermal analysis of a hypereutectic Al-Si alloy used for an automotive part was carried out in this research work. Solidification characteristics are recognized from the Temperature-time curve and its corresponding derivatives. This analysis was successfully used in a simulation software program with the aim of improving the resultant simulation accuracy. In this study, different types of molds, with and without cooling systems, were designed and used. The melt present in the furnaces of the factory was used to simulate the casting process. The effect of different cooling rates (1.2ºC/s, 2ºC/s, 2.3ºC/s and 2.9ºC/s) on the solidification parameters have been investigated. Differences in the resultant microstructure between wall and center of the molds have been analyzed and have been related to the T-t curve. Finally, the experimental results clearly indicate that the water-cooling rate of the molds and the melt temperature directly affects the solidification process as well as the final microstructure.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

This study involved the fabrication of a set of Aluminum ion-grafted SBA-15 utilizing ethylene-diamine and trimethylamine ionic liquids. The primary objective was to examine the impact of the fabrication environment on the physicochemical characteristics of the catalysts. Comprehensive characterization of the Al-SBA-15 catalysts was conducted using various techniques, including XRD, FTIR, surface area, pyridine FTIR, 27Al-NMR, TGA, HRTEM, and FESEM, to analyze their physicochemical characteristics. Furthermore, the acidic characteristics were examined by con-ducting potentiometric titration in a nonaqueous solvent and employing FTIR spectroscopy to an-alyze the chemisorbed pyridine. The effectiveness of the fabricated acid materials was evaluated by testing their performance in the acetic acid esterification with butanol. The findings obtained reveal that the mesostructured of SBA-15 remains intact following the successful inclusion of Al3+ ions into the silica frameworks. Additionally, a remarkable enhancement in the existence of both Bronsted and Lewis acid centers is noted due to the grafting process of Al3+ ions. At temperatures of 80°C and 100°C, the reaction in Al-SBA-15(T-120) proceeds swiftly, reaching approximately 32% and 38% conversion, respectively, within a span of 110 minutes. The excellent catalytic performance observed in the esterification reaction can be attributed to two factors: the homogeneous distribution of Al3+ ions within the SBA-15 frameworks and the acidic character of Al-SBA-15. The findings further indicate that the grafting process for incorporating Al3+ ions into the silica matrix is more efficient.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

The drought is one of all phenomena at local to a global scale that caused climate change impacts, alongside it also the human activities related, which were deforested and land use changed that caused to ecological disturbance, which one is hydrological changes. Hence, it’s a lot of lost productivity, chiefly to farming land aspects and the other, so the land restoration by reforestation is needed in framework to water cycle (hydrology) process kindly. The aim of this research has identified and analyzed ecological restoration to ecosystem services, chiefly in wastewater management (treatment) to conservation, especially in Al Zaytun areas (Pesantren), so observing and in-depth individual interview (with some of personage and pesantren of boards) is one method that used to data collected, alongside land survey management to classified type development in Al Zaytun areas. The result of this research revealed that Al Zaytun successfully in water management to conservation by wastewater treated management by Eichhornia crassipes (Enceng gondok), afterward to the reservoir as water saved development. Those conservation types considered capability in reviving to ecological systems to ecosystem services increased kindly, alongside to land restoration by some of the plant species or trees to grow and developed in which Tectona grandis L. f is more dominantly and it's favorite because of investment economic that advantage based on ecological perspective. These were type management that did by Al Zaytun, alongside its able in coping to both drought and climate change impacts kindly and adaptively, and of course, it’s part of an obligation as the follower’s Islam religion in preserving and maintaining natural resources, chiefly to water resources.

The effect of retrogression re-aging treatment (RRA) on corrosion behavior of 7055 Al-Zn-Mg alloy were studied. Results provides the corrosion resistance could be greatly improved by RRA. After the RRA treatment, the isolated precipitates occurred on grain boundaries (GBs) and the low angle grain boundaries (LAGBs) presented a larger fraction compared to the single-stage peaking aging. The samples after RRA treatment also show better corrosion resistance than the single-stage peak aging. The results of electrochemical impedance spectroscopy (EIS) show that impedance spectrum is consisted of semi-infinite layer diffusion impedance and stagnant Weber impedance. The semi-infinite layer diffusion impedance corresponded a limited retention layer on the electrode surface. In corrosion process, Weber impedance corresponded to stagnant layer of corrosion products generated by the anode branches. The RRA sample has the high Rf and low Cf, Cp values, and the corrosion current density of the RRA samples is ten times less than the single-stage peak aging samples with the 10% hardness losing.

The microstructure of Al-5Fe-1.5Er alloy was characterized and analyzed by using XRD, SEM, TEM and EDS. The effect of microstructure on the behavior of crack initiation and propagation was investigated by in situ tensile testing. Results show that the microstructure consists of α-Al matrix, Al₃Fe, Al₄Er, eutectic phase Al₃Fe + Al₄Er, while the 1.5 wt.% Er was added in Al-5Fe alloy. The twin structure of the Al₃Fe phase was observed, and the twin plane is {001}. Moreover, a continuous concave and convex interface structure of the Al₄Er has been found. Al₃Fe is in the form of a sheet with a clear gap inside.In situ tensile tests of the alloy at room temperature show that the crack initiation occured mainly in the Al₃Fe phase, and that the crack propagation modes include intergranular and transgranular expansion. Crack transgranular expansion is due to the strong binding ability between Al₄Er phases and surrounding organization, and the continuous concave and convex interface structure of the Al₄Er provides a significant meshing effect on the matrix and eutectic structure.

It is important for researchers in material domain to reconstruct and visualize the microstructure of alloy, which helps discover morphologies and properties that can only be found in three dimensional and microscopic space. However, because of the limitation of state-of-the-art sensors, the internal microstructure of the material is not easy to obtain. In this paper, a novel automatic 3D reconstruction method is proposed using diffraction contrast tomography technology to capture the 3D microstructure of Al-La alloy. The pipeline of the proposed method starts from the imaging of Al-La alloy with the LabDCT technique from Carl Zeiss AG, which produces a sequence of 2D microstructure sections. Then, a segmentation algorithm based on superpixel and lifted multicut is proposed to extract the 2D microstructure in an image section. Finally, 2D segmentations are joined together to reconstruct and visulize the 3D microstructure. As a result, a novel morphology of Al-La alloy is recovered with both dendrite and lamellar morphologies. The proposed method has the advantage of the ability to losslessly recover the internal microstructure.

In order to understand the hot deformation behavior of novel Cu/Al laminated composites, isothermal hot compression tests were conducted by Gleeble-1500D thermo-mechanical simulator. And the effect of bonding interface, deformation temperature and strain rate on the deformation behavior was analyzed. Results show that under the interface constraint effect, soft Al layer trends to flow synchronously with hard Cu layer. And further microstructure examinations indicate the cooperative deformation capability of Cu/Al composites increases with increasing stain rate and decreasing deformation temperature. Strain hardening exponent, calculated based on the true stress-true strain data, also proves the effect of deformation temperature and strain rate on the cooperative deformation behavior. Meanwhile, unique composites structure allows the Al matrix to exhibit the characteristic of dynamic recrystallization during the hot deformation process. Lastly, strain compensated Arrhenius-type constitutive equation was employed to describe the coupling effect of temperature, strain rate and strain on the flow stress.

Many engineering systems are described by using differential models whose solutions, generally obtained after discretization, can exhibit a noticeable deviation with respect to the response of the physical systems that those models are expected to represent. In those circumstances one possibility consists of enriching the model in order to reproduce the physical system behavior. The present paper considers a dynamical system, and proposes enriching the model solution by learning the dynamical model of the gap between the system response and the model-based prediction, while ensuring that the time integration of the learnt model remains stable. The proposed methodology is applied on the simulation of the top-oil temperature evolution of a power transformer, whose data is provided by RTE, the French Electricity Transmission System Operator.

NaClO3 and NaBrO3 are believed to form a complete solid solution from RT to fusion. The unique solid phase can thus be written: NaClO3 (1-x)-NaBrO3 (x) with: 0 ≤ x ≤ 1. This study shows that at high temperature this statement might be valid. Nevertheless, up to 50°C and probably up to 160°C and even higher temperature, this is not true when the system is in thermodynamic equilibrium. A large miscibility gap exists at room temperature (RT). This gap could be reduced up to a complete disappearance by fast crystallization, for instance by spray-drying. The necessary conditions to access to equilibrium including homochirality are also discussed.

The great pipefish Syngnathus acus is one of the most representative European syngnathid, being highly associated with seagrass and macroalgal beds. Surprisingly, the ecology of this ovoviviparous marine fish has received scanty attention. The population inhabiting three sites on Cíes Archipelago (Atlantic Islands National Park, NW Spain) was monitored in 2017-2018 for spatial and temporal changes in abundances, reproduction traits, trophic niche occupancy and dietary regimes across reproduction states through an isotopic (δ13C and δ15N) approach. Abundances were highly variable across seasons and sites, decreasing significantly from mid-autumn. The population consisted almost exclusively of large adults that migrate by the end of the breeding season, which extended from mid-spring to summer. Operational sex ratios suggest that the species is sex-role reversed. S. acus is a secondary consumer (Trophic position= 3.36 ± 0.05) preferring amphipods but displaying annual and seasonal dietary plasticity. Mature fish were less selective than immatures (especially females) with a higher preference for amphipods (36-68%) in the former. The second most preferred prey were carideans, copepods or isopods, depending on the year and reproduction state. Overall, the wider trophic niches in females and immature specimens compared to males and mature fish would indicate a higher variability in both the use of prey resources and/or their origin. The present study highlights the trophic plasticity and unique features of S. acus population in Cíes Archipelago, especially regarding the outstanding size of the fish and the exceptional occurrence of breeders.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

Change orders have received considerable attention from researchers thus far, but none have considered pricing strategies of change orders through the interaction between general contractors and subcontractors. Previous studies found that contractors’ opportunistic bidding considering beyond-contractual reward (BCR) in the execution stage can be reduced by improving the construction management system and strengthening the supervision of contractors’ performance. However, the BCR remains in ecology of construction engineering. This study proposes an integrated evolutionary game theory-system dynamics model (ET-SD model) and simulates the pricing strategy of change orders between general contractors and subcontractors to explore the root cause of BCR phenomenon. Sensitivity analysis on the evolutionary dynamics of payoff is explored. Results reveal that change orders with BCR maintain Nash equilibrium and evolutionary stable strategy (ESS) unless changing the payoff structure between general and subcontractors’ pricing strategies. This study presents important managerial insights from the evolutionary game perspectives, nature of change orders, and payoff of the alternative.

Stable isotope concentrations in the soil, rain and ground water have been used to trace the water extraction zones of plants in different environments. The need to identify the plant water use by plants in afforestation programs to control desertification increases the importance of sap water partitioning of plants in sand dune areas. However, the introduction of new plant covers exerts pressure on the water resources and can affect the local soil water conditions. In this study, we analyzed the isotope concentrations in rain, soil, sap, and ground water after the summer of 2010. Two experimental plots established in the Hailiutu catchment (Shaanxi province, northwest China) were selected to gather the water samples between September and October 2010. One plot is dominated by Salix bushes (Salix psammophila C. Wang \& Chang Y. Yang) and the other by the tree species Willow (Salix matsudana Koidz.). The total precipitation at the experimental site was 401 mm/yr during 2010, while 88.7 mm was collected in total for the period September to October. Willow trees transpired 12.82 kg/d being almost three times larger than Salix shrubs (4.57 kg/d). Despite the transpiration rates of both plant species and the few rain events in the region, the soil water beneath the plant covers is not depleted. Stable isotope signature of soil water beneath both covers shows the fractionation front in Salix at 20 cm depth and at Willow at 40 cm depth. However, soil water signature is closer to the groundwater than the collected rain water.

The central limit theorem (CLT) and its generalization to stable distributions have been widely described in literature. However, many variations of the theorem have been defined and often their applicability in practical situations is not straightforward. In particular, the applicability of the CLT is essential for a derivation of heterogeneous ensemble of Brownian particles (HEBP). Here, we analyze the role of the CLT within the HEBP approach in more detail and derive the conditions under which the existing theorems are valid.

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

Aluminum (Al) toxicity is the most common factor limiting the growth of alfalfa in acidic soil conditions. Melatonin (MT), a significant pleiotropic molecule present in both plants and animals, has shown promise in mitigating Al toxicity in various plant species. This study aims to elucidate the underlying mechanism by which melatonin alleviates Al toxicity in alfalfa through a combined physiological and transcriptomic analysis. The results reveal that 5 μM MT significantly alleviates Al-induced growth inhibition and preserves the morphology of root tip cells. Moreover, MT application reduces Al accumulation in alfalfa roots and shoots by 28.6% and 27.6%, respectively. Additionally, MT plays a crucial role in scavenging Al-induced excess H2O2 by enhancing the activities of superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT), consequently reducing malondialdehyde (MDA) levels. The RNA-seq results reveal that MT application significantly upregulates the expression of xyloglucan endotransglucosylase/hydrolase (XTH) and carbon metabolism-related genes, including those involved in the glycolysis process, as well as sucrose and starch metabolism, suggesting that MT application may mitigate Al toxicity by facilitating the binding of Al to the cell walls, thereby reducing intracellular Al accumulation, and by improving respiration and the content of sucrose and trehalose. Taken together, our study demonstrates that MT alleviates Al toxicity in alfalfa by restoring redox homeostasis, enhancing Al binding to the cell wall, and modulating carbon metabolism. This research advances our understanding of the mechanisms underlying MT's effectiveness in mitigating Al toxicity, offering potential strategies for reducing Al accumulation in alfalfa.

Saudi Arabia consists mainly of desert land. However, it has big and small natural wetlands and artificial wetlands. Most of these wetlands are seen along the Red Sea and the Arabian Gulf coastal regions. Al-Asfar Lake, located in the Eastern Region of Saudi Arabia, is one of the historical landmarks of Al-Ahsa province. The primary lake water source is agricultural drainage water, which some refer to as an artificial lake. This paper mainly aims to reflect shade on the wetlands in Saudi Arabia in general and to show in detail the environmental impacts of Al-Asfar Lake on the ecosystem and biodiversity of the study area. The analytical review of the previous studies conducted in Al-Asfar Lake was adopted in this article. Hence, the impact of the lake on the land-use system, water quality and biodiversity was illustrated as the main outputs of the review analysis. However, the sustainable management of Al-Asfar Lake requires the stakeholders to adopt the wetland ecosystem health concept, which might lead to improving the lake's environmental conditions.

Fe- and Al-rich metapelite from the Transangarian segment of the Yenisey Ridge (East Siberia, Russia) is a potential new source of high-alumina refractories. The rocks have relatively high average contents of Al2O3 (20 wt.%) and Fe2O3 (7.91 wt%), moderate K2O (3.44 wt%), and low CaO (0.74 wt%). Their dominant mineral assemblages are andalusite + muscovite + margarite + chlorite + biotite + quartz or staurolite + kyanite or/and andalusite + chlorite + muscovite + biotite + quartz with ±garnet and ±plagioclase. Al2SiO5 polymorphs occur as up to 1.5 cm andalusite porphyroblasts and partial or complete pseudomorphs after andalusite (kyanite and staurolite). Accessories include abundant Fe-Ti oxides and sporadic REE-, Y-, Ca-phosphates; sulfides are negligible. The composition of Al2SiO5 concentrates obtained in laboratory by heavy-media and magnetic separation from ≥0.06 mm fractions meet all requirements for raw material of this type: &gt;56 wt% Al2O3, &lt;42 wt% SiO2, &lt;1 wt% Fe2O3, &lt;1.2 wt% TiO2, and &lt;0.2 wt% (CaO+MgO). The andalusite, kyanite, and mixed ores yield 0.7-4.1 wt%, 0.7-2.2 wt%, and 1.9-6.0 wt% of concentrate, respectively. The best-quality ores rich in Al2SiO5 polymorphs reside in zones of contact and/or dynamic metamorphism superimposed over regional metamorphism of Al-rich rocks.

The cast defects strongly degrade the mechanical properties in cast alloys. The effect of Sn addition on Al-Si alloys was investigated by 3D computed tomography, SEM and TEM. Amorphous Sn oxides are found near the alumina film, cause more shrinkage pores, initiate cracks and deteriorate mechanical properties. This work suggests not adding Sn in various Al alloys used in cast state.

The effects of partial replacement of Si by Al on the microstructure, tensile properties, and Charpy impact toughness were investigated using 0.2%C-Si/Al-Mn-Cr-B TRIP-aided martensitic steels. The impact toughness was related to the microstructural and mechanical properties. The partial re-placement decreased the volume fraction of retained austenite and increased the mechanical stabil-ity, accompanied by softening and an increase in the volume fraction of the primary martensite. Resultantly, the partial replacement decreased strength and ductility. The impact absorbed energy (value) at 25 C was slightly increased by the partial replacement. The increased impact absorbed energy was mainly caused by high crack/void propagation energy due to the softened primary martensite and a small contribution of the stabilized retained austenite. The 50% shear fracture ductile-to-brittle transition temperature was marginally raised by the partial replacement. The raised transition temperature was mainly associated with an increase in a unit crack path of qua-si-cleavage/cleavage fracture.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

Aluminum base alloys containing chromium (Cr) and zinc (Zn) were produced using extrusion and heat treated powder metallurgy. Cr addition ranged between 5 to 10 wt. % while Zn was added in an amount between 0 to 20 wt. %. Heat treatment processes were performed during powder metallurgy process at different temperatures followed by water quenching. Similar alloys were extruded, with an extrusion ratio of 4.6 to get proper densification. Optical microscopy was used for microstructure investigations of the produced alloys. The element distribution microstructure study was carried out using the Energy Dispersive X-ray analysis method. Hardness and tensile properties of the investigated alloys have been examined. Wear resistance tests were carried out and the results were compared with these of the Al-based bulk alloys. Results showed that the aluminum base alloys containing 10wt. % Chromium and heat treated at 500°C for one hour followed by water quenching exhibited the highest wear resistance and better mechanical properties.

Despite saltmarshes being considered as nature-based solutions (NbS) towards climate change mitigation, India’s saltmarsh ecosystems are least studied. This study quantifies the seasonal variation in carbon stocks mono-specific saltmarsh species (Porteresia coarctata) and its potential to play an important role in India’s climate change mitigation plans. Seasonal (pre-and post-monsoon) sampling of P. coarctata surface water, biomass and 30 cm sediment core was collected across four locations on the east coast of India to quantify sediment dry bulk density (DBD), organic matter (OM%), organic carbon (Corg%), Corg stocks of sediment and biomass, total carbon (C%) and nitrogen (N%) and stable isotopes of δ13C and δ15N. In general, the sediment DBD, OM and Corg of P. coarctata meadows was higher in post-monsoon and was influenced by salinity and pH changes. Isotope (δ¹³C) modelling of various sediment C sources suggested, particulate organic matter (POM) contribution was highest (0.04-0.79%) followed by P. coarctata (0.01–052%) and other macrophytes across our study locations. The seasonal variation of δ¹³C showed increased contribution of marine derived particulate and dissolved organic matter into P. coarctata meadows in post-monsoon season. Heavier δ¹⁵N values were observed in post-monsoon season suggesting anthropogenic input, that was utilized by P. coarctata to increase its above and below-ground biomass and shoot density. The combined ecosystem (30 cm sediment + biomass) Corg stocks of P. coarctata was 1.7-fold higher in post-monsoon (4021.20± 917 Mg C) compared to pre-monsoon (2297.36 ±647 Mg C) season among the four locations with a sediment Corg contribution >70%. Based on the International Panel for Climate Change Tier II assessment the P. coarctata meadows (443 ha) can help in avoiding the pre and post-monsoon emissions of 8431.34 and 14757.84 Mg CO₂ respectively. The combined price of the total CO₂ equivalent stored in P. coarctata meadows in pre- and post-monsoon is US$ 14.50 and US$ 25.38 million respectively. Further studies quantifying the NbS potential of P. coarctata mono-specific and mixed meadows of India’s coast is needed along with integration of saltmarsh ecosystems into India’s National Action Plan on Climate Change.

Femtoscopy is a unique tool to investigate the space-time geometry of the matter created in ultra-relativistic collisions. If the probability density distribution of hadron emission is parametrized, then the dependence of its parameters on particle momentum, collision energy, and collision geometry can be given. In recent years, several measurements came to light that indicated the adequacy of assuming a Lévy-stable shape for the mentioned distribution. In parallel, several new phenomenological developments appeared, aiding the interpretation of the experimental results, or providing tools for the measurements. In this paper we review and discuss some of these advances, phenomenological and experimental.

The study of trophic relationships among closely related species plays an important role in deepening our understanding of the resource utilization characteristics, differentiation patterns, and population dynamics of co-occurring species in the same habitat. This research uses two congeneric fish species, Pennahia pawak and Pennahia anea, as examples. Based on stomach content analysis and carbon-nitrogen stable isotope analysis, a comparative analysis of their feeding habits and trophic niches is conducted. Additionally, spatial niche analysis is employed to explore the coexistence and competitive mechanisms between these two closely related fish species. The results showed that both P. pawak and P. anea had similar feeding habits, mainly feeding on Pisces and Macrura, but there were some feeding preferences between the two species. Interspecific prey overlap was meaningful but not significant, with an overlap coefficient of 0.56. There were significant differences in feeding habits between the two species during different seasons. Based on stable isotope analyses, body length of both species had a significant positive correlation with δ15N (Pearson r=0.65, P&lt;0.01; Pearson r=0.44, P&lt;0.01), but not with δ13C (P&gt;0.05). Standard ellipse corrected area (SEAc) of P. pawak and P. anea were 0.65 and 1.16, while the trophic niche overlap was only 0.29, which was not significant; the spatial niche width of the two was 1.19 and 0.58, respectively, and the spatial niche overlap was only 0.20, which was not significant. Intra-species competition was intense in P. pawak and P. anea, but reduced feeding specialization had a mitigating effect on intra-species competition. Interspecific competition was present but not significant, and was mitigated by trophic and spatial niche differentiation.

A key response to glucose stress is an increased production of unsaturated fatty acids to balance the increase of saturated fatty acids in the membrane. The C. elegans homolog of stearoyl-CoA desaturase, FAT-7, introduces the first double bond into saturated C18 fatty acids yielding oleic acid and is a critical regulatory point for surviving cold and glucose stress. Here, we incorporated 13C stable isotopes into the diet of nematodes and quantified the 13C-labelled fatty acid by GC-MS and HPLC/MS-MS to track the metabolic response to various concentrations of glucose. Previous work has analyzed membrane composition of C. elegans when responding to mild glucose stress and showed few alterations in overall fatty acid composition in the membrane. Here, in nematodes exposed to higher concentrations of glucose, a specific reduction of oleic acid and linoleic acid was observed. Using time courses and stable isotope tracing, the response of fatty acid me-tabolism to increasing levels of glucose stress has been characterized, revealing a funneling of monounsaturated fatty acids to preserve polyunsaturated fatty acid abundance. Taken together, higher levels of glucose unveil a specific reduction of oleic and linolenic acid in the metabolic re-wiring required to survive glucose stress.

In this work, an entropy-stable and well-balanced numerical scheme for a one-dimensional blood flow model is presented. Such scheme is obtained from an explicit entropy conservative flux along with a second order discretization of the source term by using centered finite differences. We prove that the scheme is entropy-stable and preserves steady-states solutions. In addition, some numerical examples are included to test the performance of the proposed scheme.

Groundwater plays a crucial role in triggering and reactivating deep-seated landslides. However, classical hydrogeological investigations have limitations in their applicability to deep-seated landslides due to anisotropic and heterogeneous media[16]. The Huangtupo landslide in the Three Gorges reservoir area has garnered significant attention in China due to its large volume, complex geological structure, and high hazard potential. Recent monitoring data has shown notable deformation in the NO.1 Riverside Sliding Mass (HTP-1), one of the four parts of the Huangtupo landslide, making it the primary focus of landslide research. This study aimed to investigate the water sources in the HTP-1 landslide using environmental stable isotopes as tracers. The isotopic analysis results indicated that the groundwater in the landslide area (LGW) is a mixture of remote karst groundwater (KGW) from the adjacent up-slope and local precipitation (LP). The karst groundwater is a major contributor to the recharge of the landslide groundwater system, causing a high slope groundwater level that can easily exceed the critical level during heavy rainfall events. Furthermore, based on the differential distribution of the LP fraction of LGW at different locations, the groundwater in the landslide can be classified into three groups. Groundwater at the sliding rupture surface has the highest fractions of local precipitation, followed by the groundwater at the rear of the landslide. Combined with the monitoring data of groundwater level in boreholes during the rainy season, this indicates that fissures and fractures in the sliding rupture zone and at the back of the landslide are well connected, which could be a critical factor in the mass movement of the creeping slope.

The decline in Pinus sylvestris var. mongolica in the introduction area has had a high profile in recent years. For the ecological restoration, management and silvicultural design of Mongolian pines in the introduction area, it is necessary to conduct a comprehensive and in-depth study on the ecological adaptation mechanism of Mongolian pines in provenances. The ecological process of water and nutrient accumulation as well as the influence of environmental factors on the photosynthetic physiology are the key to revealing the ecological adaptation mechanism of Mongolian pines. According to the differences of climate in the distribution area of Mongolian pines, sampling sites were set up, the effects of environmental factors on leaf δ13C and the relationship between leaf δ13C and nutrient content were analyzed. The results showed that leaf δ13C values were ranging from - 29.7 ‰ to - 23.76 ‰. The ecological stoichiometry, including LC (522.81 mg·g-1), LN (16.04 mg·g-1), LP (1.19 mg·g-1) and L-N:P (13.56), indicated that leaf photosynthesis and water use efficiency is greatly affected by environmental conditions, Mongolian pines had strong ability of carbon fixation, and its growth was obviously restricted by nitrogen. Although there was no significant correlation between δ13C with stoichiometric parameters in leaf, photosynthesis was the key link in the process of carbon fixation. It also showed that Pinus sylvestris var. mongolica was a stomatal limited plant. Leaf δ13C had significant correlation with climatic factors. VPD is the dynamic factor affecting the photosynthetic physiological process in leaves. Air and soil moisture are the dominate factors affecting the leaf stomatal conductance and determines leaf δ13C value, while other factors indirectly affect leaf δ13C by its impact on relative humidity or soil water content. Soil phosphorus content affected by clay is a key factor affecting soil water availability and soil nutrient cycling. Photosynthetic process in leaf is the dynamic process affecting the nutrient accumulation.

Stable-isotope dimethyl labeling is a highly reactive and cost-effective derivatization procedure that could be utilized in proteomics analysis. In this study, a liquid chromatography-tandem mass spectrometry in multiple reaction monitoring mode (LC-MS-MRM) platform for the quantification of kiwi allergens was first developed using this strategy. Three signature peptides for target allergens Act d 1, Act d 5, and Act d 11 were determined and were derivatized with normal and deuterated formaldehyde as external calibrants and internal standards, respectively. The results showed that sample preparation with the phenol method provided comprehensive protein populations. Recoveries at four different levels ranging from 72.5–109.3% were achieved for the H-labeled signature peptides of Act d 1 (SPA1-H) and Act d 5 (SPA5-H) with precision ranging from 1.86–9.92%. The limit of quantification (LOQ) was set at 8 pg mL–1 for SPA1-H and at 4 ng mL–1 for SPA5-H. The developed procedure was utilized to analyze seven kinds of hand-made kiwi foods containing 0.0175–0.0515 mg g–1 of Act d 1 and 0.0252–0.0556 mg g–1 of Act d 5. This study extended the applicability of stable-isotope dimethyl labeling to the economical and precise determination of food allergens and peptides.

Nitrogen (N) is an essential nutrient and plays an important role in plant growth and physiology. In addition, N is also the limiting nutrient in most terrestrial ecosystems. The increasing use of N fertilizers increases agricultural production, but also has negative impacts on biodiversity, water quality and increases emissions of greenhouse gases such as nitrogen oxides (NOx) and nitrous oxide (N2O) into the atmosphere. N2O is a strong greenhouse gas and the product of microbial transformation processes of N introduced into soil and groundwater (nitrification and denitrification). The production of N2O in soils is highly dependent on oxygen and water content, soil temperature and texture and the available amount of reactive nitrogen (NO3- or NH4+). In agricultural soils, N2O emissions are also influenced by the type of fertilizer used, crops grown, soil pH and NO3- concentration. Refined forms of land management, such as the cultivation of legumes, can reduce the use of fertilizers and thus also the emission of N2O. Legumes can use symbiotic nodule bacteria (rhizobia) to bind atmospheric N2 and make it available to the plant. Non-symbiotic soil microorganisms such as cyanobacteria or other heterotrophic and autotrophic prokaryotes are also able to fix N2. Furthermore, the N2-fixing enzyme nitrogenase, which is specific for most organisms, is not specific for other N2 compounds, especially N2O. To study the N2 and N2O fixation potential of soils and legumes, experiments with isotope-enriched N-gases (100 mol% 15N2 and 15N2O) were performed. Three different soil types (forest, meadow and wetland) as well as legume plants inoculated with rhizobia bacteria (Rhizobium leucaneae) (Leucaena leucocephala) were incubated in microcosms with different mixing ratios of N2 and N2O over a period of one week. The measured 15N enrichment was then used to determine the biological uptake rates. Both in plants and in soils admixtures of up to 40% N2O had no influence on the N2 fixation rate. N2 uptake rates were 1.2 ± 0.4 ug N gdw-1 d- 1in forest and grassland soils and 3.9 ± 1.2 ug N gdw-1 d- 1 in wetland soils. In contrast, the N2 fixation rates of leguminous plants were significantly higher (130 ± 40 ug N gdw-1 d- 1), with the highest accumulation not in root nodules but in the roots. In both plants and soil, the N2O fixation of 0.2 ± 0.1 ug N gdw-1 d- 1 could only be measured from a concentration of 4 vol%. The results indicate that both soils and legumes have a high potential to bind atmospheric nitrogen in the form of both N2 but not N2O. The fate of nitrogen in soil needs to be further investigated. N2 fixation seems to play an important role in wetland soils. Legumes in particular have the potential for NH4+ input and N2O reduction, as most of the solid nitrogen has been transferred to the roots, which can contribute significantly to soil nutrient input.

The present study describes the preparation of a composite material consisting of thermoplastic polyurethane-poly (n-isopropylacrylamide) (TPU-PNIPAM), which was employed for the se-lective adsorption separation of alcohol/water mixed solutions for the first time. The findings revealed that TPU and PNIPAM were interconnected through interchain hydrogen bonding, resulting in exposed hydrophobic isopropyl groups while covering the hydrophilic hydrogen bond sites. Selective separation of alcohols from alcohol/water mixed solutions occurred via London dispersion forces between alkyl groups. Increasing the PNIPAM load on the TPU surface led to a decrease in available hydrogen bond sites capable of bonding with water molecules, an increase in dispersible isopropyl groups interacting with alcohol alkyl groups, and enhanced selective adsorption capacity of TPU-PNIPAM towards alcohol/water mixed solutions. Moreover, TPU-PNIPAM exhibited a characteristic fast-slow-fast-equilibrium ad-sorption curve for different initial concentrations of alcohol/water mixtures, and its selective adsorption capacity increased when temperature reached 55℃. In addition to these general trends, under identical conditions, the selective adsorption capacity of TPU-PNIPAM gradually increased by methanol < ethanol < isopropyl alcohol < propyl alcohol, thus indicating a positive correlation between selectivity performance and hydrophobicity level.

Aluminum (Al) and manganese (Mn) toxicity are the top two constraints to crop production in acid soil. Crops have evolved common and specific mechanisms to tolerate the two stresses. In the present study, the responses (toxicity and tolerance) of wheat near-isogenic lines (ET8 and ES8) and their parents (Carazinho and Egret) to Al and Mn were compared by determining physiolog-ical parameters and transcriptome profiling of roots. The results showed that: (1) Carazinho and ET8 exhibited dual tolerance to Al and Mn as compared with Egret and ES8, indicated by higher relative root elongation and SPAD; (2) After entering into roots, Al was mainly distributed in the root and fixed in the cell wall, while Mn was mainly distributed in the cell sap and then trans-ported to leaves. Both Al and Mn stresses decreased the contents of Ca, Mg, and Zn; Mn stress al-so inhibited the accumulation of Fe, while Al showed an opposite effect; (3) Transcriptomic analy-sis identified 5581 differentially expressed genes (DEGs) under Al stress and 4165 DEGs under Mn stress. Among these, 2774 DEGs were regulated by both Al and Mn stresses, while 2280 and 1957 DEGs were exclusively regulated by Al and Mn stress, respectively. GO and KEGG analyses indi-cated that cell wall metabolism responds exclusively to Al, while nicotianamine synthesis exclu-sively responds to Mn. Pathways such as signaling, phenylpropanoid metabolism, and metal ion transport showed commonality and specificity to Al and Mn. TFs, such as MYB, WRKY, and AP2 families, were also regulated by Al and Mn, and WGCNA identified PODP7, VATB2, and ABCC3 as the hub genes for Al tolerance and NAS for Mn tolerance. The identified genes and pathways can be used as targets for pyramiding genes and breeding multi-tolerant varieties.

In this study, the effects of combined addition of CeLa and GdY on microstructure and mechanical properties of as-cast Al-4Cu-1Mn alloys were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopies (TEM) and tensile testing. The results show that the minor addition of CeLa and GdY leads to the refinement of grain size. The addition of CeLa results in the formation of supersaturated vacancies in the Al matrix, whereas the addition of GdY leads to a decrease in the precipitation temperature of the Al2Cu phase. The combined CeLa and GdY addition can significantly increase ultimate tensile strength (UTS) while losing only a small amount of elongation (EL). Compared with the unmodified alloy, the grain size and SDAS of the alloy (0.2 wt% CeLa + 0.1 wt% GdY) were diminished by 67.2% and 58.7%, respectively, while maximum hardness and UTS rose by 31.2% and 36.9%, correspondingly.

In this study, the effect of increasing exposure time on microstructures, defectiveness, mechanical properties and corrosion behavior of selective laser melted sample Al-Si10-Mg powder have been investigated. The sample were processed at the same power (375 W) and scan speed (2000 mm/s) but with increasing exposure time. Exposure time equal to 40, 50 and 60 µs was applied. The features of the analyzed samples show that with increasing exposure time a better efficiency of the heat input has been obtained with larger size of melting pool and Si particles and lower defectiveness. Moreover, being the coarser microstructure associated a to lower level of voids, the average hardness is similar for the analyzed samples. The potentiodynamic curves of the samples show that the voids occurrence is more significant with respect to the scale of micro-structure on corrosion behavior being the sample processed at the highest exposure time the more resistant to corrosion. The experimental techniques used in the present study were Optical microscope, Sem microscope, Hardness and X-Ray Computed Tomography.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

Recent years have seen dramatic growth in the number of scholarly scientific works dedicated to the topic of Artificial Intelligence (AI), banking, and finance. With the development of scientometric tools, it is now possible to map, visualize, analyze, and assess scientific activities in many fields of engineering and social sciences including Islamic banking and finance. Based on data retrieved from the Scopus database and using a qualitative method, this study investigates, evaluates, and identifies significant development, trends, and players in the application of AI in Islamic banking and finance using the Visualization Of Similarities Method (VOS) between objects in VOSviewer. From 2006 to 2022, 387 documents were retrieved from the Scopus database; Results revealed that the top five most active countries in terms of publications are Malaysia (117 documents), Indonesia (89 documents), the United Kingdom (36 documents), the USA (24 documents), and Saudi Arabia and Bahrain (24 documents each). The International Islamic University Malaysia and Universitas Indonesia came out on top of active institutions while the top funding source came from the Ministry of Higher Education, Malaysia. The comprehensive findings and analysis reported in this study serve as a roadmap for future academics to create theory and practice for applying AI in Islamic banking and finance.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Training supervised machine learning models requires labeled examples. A judicious choice of examples is helpful when there is a significant cost associated with assigning labels. This article improves upon a promising extant method – Batch-mode Expected Model Change Maximization (B-EMCM) method – for selecting examples to be labeled for regression problems. Specifically, it develops and evaluates alternate strategies for adaptively selecting batch size in B-EMCM. By determining the cumulative error that occurs from the estimation of the stochastic gradient descent, a stop criteria for each iteration of the batch can be specified to ensure that selected candidates are the most beneficial to model learning. This new methodology is compared to B-EMCM via mean absolute error and root mean square error over ten iterations benchmarked against machine learning data sets. Using multiple data sets and metrics across all methods, one variation of AB-EMCM, the max bound of the accumulated error (AB-EMCM Max), showed the best results for an adaptive batch approach. It achieved better root mean squared error (RMSE) and mean absolute error (MAE) than the other adaptive and non-adaptive batch methods while reaching the result in nearly the same number of iterations as the non-adaptive batch methods.

This paper reports on the fabrication of alumina doped preforms using MCVD-vapor phase chelate delivery system with Al(acac)3 as the precursor. The objectives of the work are to study the deposition process, the efficiency of the fabrication process, and the quality of the fabricated fiber preforms. Two parameters are studied, Al(acac)3 sublimator temperature (TAl°C) and deposition direction (i.e. downstream and upstream). Other parameters such as oxygen flow and deposition temperature are fixed. The results showed that a high uniformity of refractive index difference (%RSD &lt; 2%) and core size (%RSD &lt; 2.4%) was obtained along the preform length using downstream deposition while for the combined upstream and downstream deposition the uniformity was deteriorated. The process efficiency was found to be about 21% for TAl°C of 185°C and downstream deposition. From the EDX elemental analysis, the refractive index was found to increase by 0.0025 per mole percent of alumina.

Recently, the environment is being put under constantly increasing pressure. Globally, water shortage is considered as one of the most serious environmental problems which affect human life and plant wealth. Iraq is highly affected by water deficit in many regions. In particular, Al-Najaf region is selected to be under evaluation for the current and future water resources shortage. This study is based on the collected data for rainfall, evaporation, flow-rate, groundwater, water needed for irrigation, and daily uses for the period between 2000 and 2018. The Artificial Neural Network, normal distribution, and lognormal distribution type III are applied for analyzing the collected data in addition to predict the water shortage for year 2050. Results show a water shortage in years 2002, 2004, 2005, and 2017 only for the selected period. A Simulink model is constructed using Matlab to increase the credibility of the estimated results and gives accurate results for the groundwater and surface water needed. Where in 2050, it is found that it needs to use the groundwater source by 0.024 x 10⁹ m³ to support the surface water source which is represented by the Euphrates River. The study shows the extent of inefficient management of water resources in Al-Najaf region.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

Semi-solid feedstock of AZ80 magnesium alloy modified by minor rare-earth Y element (0, 0.2, 0.4, 0.8 wt.%) were fabricated by strain induces melting activated (SIMA) in the form of extrusion and partial remelting. The effect of Y addition on the microstructure evolution of extruded and isothermal treated alloy was observed by optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and quantitative analysis. The results show that the Y addition can refine the microstructure and make the β-Mg17Al12 phases agglomerating. During the subsequent isothermal treatment at 570℃, the average solid grain size, shape factor and liquid fractions increased with prolonged soaking time. Smaller spheroidal solid grains and the larger shape factor were obtained due to Y addition. The coalescence and Ostwald ripening of solid grains operated the coarsening process simultaneously. The coarsening rate constants of AZ80M1 (0.2 wt.% Y addition) of 164.22 μm3s-1 was approximately four times less than the un-modified AZ80 alloy of 689.44 μm3s-1. In contrast, the desirable semi-solid structure featured by fine, well globular solid grains and appropriate liquid fractions and shape factor was achieved in AZ80M1 alloy treated at 570℃ for 20-30 min.