Commuting to work by private vehicle is one of the main sources of air pollution in cities, mainly from NO2 and particulate matter (PM2.5 and PM10). With the spread of telework, traffic congestion during peak hours is reduced on certain days of the week, improving air quality. This study an-alyzes the relationship between the improvement of air quality improvement and urban traffic resulting from teleworking activities after the COVID-19 pandemic in Madrid, Spain. The article considers road traffic and teleworking before the COVID-19 pandemic (2018 and 2019), during the pandemic (2020 and 2021) and in the period after (2022 and 2023) in the city center and the in-fluence on certain environmental factors. Daily NO2, PM2.5, PM10, and O3 concentration data were collected at air quality stations in Madrid municipality, traffic data and some meteorological variables such as wind speed, precipitation and temperature were considered. When conducting correlation and regression analysis among the variables it shows a clear association between NO2 and traffic before the pandemic, which is lower for both PM and O3. This correlation was main-tained during the pandemic, except for O3, whose association increased during this period and then decreased in the later period due to various motives. These results seem to indicate the ex-istence of a relevant relationship between urban mobility and air quality and an especially rele-vant relationship with telework, suggesting the need for policies aimed at promoting sustainable mobility in the future.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

Different coffee drying technologies face complex task in ensuring an acceptable final seed moisture content. Drying technology of agricultural commodities aims to maintain and improve the quality of the agricultural products themselves. In addition to maintaining quality, especially from other bacterial attacks, it can last for a long time before further processing. Coffee commodities are promising for the welfare of coffee farmers. Drying technology plays a major role in determining the quality of coffee. Various drying models are applied including the traditional model that until now is still applied, direct drying under solar radiation. However, this drying process is less hygienic and requires a large area. Thus, one of the drying technologies that can accelerate drying time is to vary the air flow in the drying chamber so that the coffee can be determined to reduce the water content with a certain temperature. In this study, it was found that the moisture content of coffee beans dried using a dryer on air flow with variations of velocity in solar collector 1 (DB1) air velocity of 1.0m/s obtained the final mass = 732.249 gr, solar collector 2 (DB2) with air velocity 1.5 m/s obtained the final mass = 774.70 gr, solar collector 3 (DB3) with air velocity 2.0 m/s obtained the final mass = 855.10 gr, solar collector 4 (DB4) with air velocity 2.5 m/s obtained the final mass = 745.79 gr, and solar collector 5 (DB5) with air velocity 3.0 m/s obtained the final mass = 786.40 gr. Water Content DB1=12.0%, DB2=13.6%, DB3=18.5%, DB4=12.9% and DB5=15.2%. The time required for 25 hours with a maximum radiation of 586.9 w/m2, total heat utilized from solar radiation in 3 days =16.663128 MJ/m2. from the initial weight of 1500gr coffee bean samples and dried in five solar collectors with parallel simultaneously. The evaporated water content DB1=51.18%, DB2=48.35%, DB3=42.96%, DB4=50.28% and DB5=47.57%. Based on this research, it was found that the most optimum quality of coffee was by using solar collector 2 (DB2), namely with air flow of 1.5 m/s with average temperature in the drying box DB2=43.68°C, with the quality content of the coffee, Protein content=12.2%, Carbohydrate=22.8% and Free Fatty Acid (ALB) content=0.05%.

We investigate the impact of air quality and weather on the equity returns of the Shenzhen Exchange. To capture the air quality and weather effects, we use dummy variables created by employing a moving average and moving standard deviation. The important results are as follows. First, in the whole sample period (2005–2019), we find that high air pollution and extremely high temperature have significant and negative influence on the equity returns. In the sub-period I (2005–2012), the 11-day model and 31-day model show that high air pollution have significant and negative impacts on the Shenzhen stock returns. Second, the results of the quantile regression show that high air pollution have significant and negative effects during bullish market phase, and extremely high temperature have significant and negative effects during bearish market phase. This implies that the air quality and weather effects are asymmetric. Third, the weather effect of the abnormal temperature on the stock returns is greater in severe bearish market. Whereas the effect of the air pollution on the stock returns is greater in the bullish market. Fourth, the least squares method underestimates the air quality and weather effects compared to the quantile regression method, suggesting that the quantile regression method is more suitable in analyzing these effects in a very volatile emerging market such as the Shenzhen stock market.

In early 2020 from April to early June, the metropolitan area of Sydney as well as the rest of New South Wales (NSW, Australia) experienced a period of lockdown to prevent the spread of Covid-19 virus in the community. The effect of reducing anthropogenic activities including transportation had an impact on the urban environment in term of air quality which is shown to have improved for a number of pollutants, such as nitrogen dioxides (NO2) and carbon monoxide (CO), based on monitoring data on ground and from satellite. Besides primary pollutants CO and NOx emitted from mobile sources, PM2.5 (primary and secondary) and secondary ozone (O3) during the lockdown period will also be analysed using both air quality data and modelling method. The results show that NO2, CO and PM2.5 levels decreased during the lockdown, but O3 instead increased. The change in the concentration levels however are small considering the large reduction in traffic volume of ~30%. By estimate the decrease in traffic volume in Sydney region, the corresponding decrease in emission input to the WRF-CMAQ (Weather Research and Forecasting - Community Multiscale Air Quality Modeling System) air quality model is then used to estimate the effect of lockdown on the air quality especially CO, NO2, O3 and PM2.5 in the Greater Metropolitan Region (GMR) of Sydney. COVID-19 lockdown period is an ideal case to study the effect of motor vehicle and mobile source contribution to air pollutants such as those listed above in the GMR.

Air pollution knows no boundaries, which means for a city or a region to attain clean air standards, must not only look at the emission sources within its own administrative boundary, but also at sources in the immediate vicinity and those originating from long-range transport. And there is a limit to how much area can be explored to evaluate, govern, and manage as designated airsheds for cities and larger regions. This paper discusses the need from an official airshed framework for India’s air quality management, urban airsheds designated for India’s 131 non-attainment cities under the national clean air programme, and proposes climatically and geographically appropriate regional airsheds to support long-term planning. Between 28 states, eight union territories, 36 meteorological sub-regional divisions, and six regional meteorological departments, establishing the proposed 15 regional airsheds for integrated and collaborative air quality management across India is a unique opportunity.

We investigate the impact of air quality and weather on the stock market returns of the Shenzhen Exchange. To capture the air quality and weather effects, we apply dummy variables generated by applying a moving average and moving standard deviation. Our study provides several interesting results. First, in the whole sample period (2005–2019), we find that high air pollution and extremely high temperature have significant and negative effects on the Shenzhen stock returns. In the sub-period I (2005–2012), the 11-day model and 31-day model show that high air pollution have significant and negative effects on the Shenzhen stock returns. Second, the results of the quantile regression show that high air pollution have significant and negative effects during bullish market phase, and extremely high temperature have significant and negative effects during bearish market phase. This implies that the air quality and weather effects are asymmetric. Third, the more the Shenzhen stock returns drop, the greater the effect of the abnormal temperature is. Whereas, the more the Shenzhen stock returns increase, the greater the effect of the abnormal air quality is. Fourth, the least squares method underestimates the air quality and weather effects compared to the quantile regression method, suggesting that the quantile regression method is more suitable in analysing these effects in a very volatile emerging market such as the Shenzhen stock market.

Air pollution is a leading cause of death worldwide, and has a profound impact on the planet's climate and ecosystems. A substantial portion of air pollution is attributable to Ocean Going Vessels (OGVs). In light of this, international regulations have been put in place to mitigate air pollutant emissions from OGVs. While studies have indicated that these regulations can create significant health, environmental, and economic benefits, there remains a research gap regarding their specific impact on enhancing air quality. The aim of this study is to investigate how the implemented regulations have affected air quality in the Southern North Sea. The study found that the international regulations on ship emissions have successfully led to a decline in SO2 emissions from OGVs in the Southern North Sea, which resulted in a reduction of ambient SO2 concentrations inland, leading to positive effects on public health and the environment. However, it was projected that their proportion is tend to increase in the following years. Moreover, the study revealed that Exhaust Gas Cleaning Systems (EGCS) present significant concerns. They were significantly more frequently found to be non-compliant, and more alarmingly, they emit notably higher average levels of SO2. It also turned out that international regulations in the southern North Sea have less effect on the reduction of NOx emissions from OGVs than expected. The NOx emissions from OGVs will even account for an alarming 40% of the total domestic NOx emissions for the Belgian Region by 2030.

The term Air Quality (AQ) pertains to the standard of air, which has a direct impact on the health and well-being of individuals. It is crucial to maintain high Air Quality (AQ), for better health and productivity. Though most of people spend more time indoors nowadays, it is not to be overlooked that the pollutant concentration in indoor air is directly linked to the outdoor air quality. Due to the changes in occupancy patterns, outdated maintenance of ventilation systems, and structural flaws in buildings, the indoor air is significantly polluted; pollutants emitted outdoors enter indoor air through open windows, ventilation systems and infiltration. In this paper, we have proposed a new technique, DTMCPM (discrete-time Markov chain (DTMC) model for the analysis and forecasting of AQ, using the power method). Specialized sensors and equipment to measure different pollutants, such as particulate matter, ozone, nitrogen dioxide, sulfur dioxide, benzene and toluene, are used to collect data by the Institute of Pakistan Air Quality Monitor in various cities; the data is converted to US EPA standard for all pollutant species. This data is used to calculate the transition matrix, steady-state values and mean return rate for the analysis of IAQ. The calculated and actual return rates have been compared and the proposed model is found to have a low average prediction error of 2.356%.

Low-cost personal exposure monitors (PEMs) to measure personal exposure to air pollution are potentially promising tools for health research. However, their adoption requires robust validation. This study evaluated the performance of twenty-one Plume Lab Flow2 (PLF) by comparing its air pollutant measurements, particulate matter with a diameter of 2.5 μm or less (PM2.5), 10 μm or less (PM10), and nitrogen dioxide (NO2), against several high-quality air pollution monitors under field conditions (at indoor, outdoor, and roadside locations). Correlation and regression analysis were used to evaluate measurements obtained by different PLFs against reference instrumentation. For all measured pollutants, the overall correlation coefficient between the PLFs and the reference instruments was often weak (r<0.4). Moderate correlation was observed for one PLF unit at indoor location and two units at roadside location, when measuring PM2.5, but not for PM10 and NO2 concentration. During periods of particularly higher pollution, 11 PLF tools showed stronger regression results (R2 values > 0.5) with one-hour and 9 PLF units with one-minute time interval. Results show that the PLF cannot be used robustly to determine high and low exposure to poor air. Therefore, the use of PLFs in research studies should be approached with caution if data quality is important to the research outputs.

A review of desiccant dehumidification technologies for improving air-quality has been presented, especially focusing on alternatives for air conditioning systems for minimizing the Sick Building Syndrome. The principles and types of desiccant wheels, as well as the existing selection software for these types of equipment, were reviewed and comparatively evaluated. The study focuses on the Brazilian context, therefore, information about air condition systems and laws of this country were evaluated. Possible applications of desiccant wheels are also analyzed, such as their integration into cooling cycles and the sensible heat wheel. Finally, several commercial desiccant wheel selection software were evaluated, which are useful in many situations. Nevertheless, it was evidenced that the available softwares are not capable of performing an operation analysis for only a specific period. Therefore, it is essential to create computational tools to select desiccant wheels, considering the data from the different Brazilian regions for a year.

The last decade has seen a significant growth in low-cost air quality monitoring systems (LCAQMS) adoption, mostly driven by the spatial density limitations of traditional regulatory grade networks which restrict their effectiveness in several settings. The EU's regulatory framework advise for deploying one air quality monitoring unit per roughly 170,000 people or 15 square kilometers which is insufficient for capturing high spatio-temporal variance in complex urban scenarios. Often these settings are characterized by distributed emissions in small roads subjected to intense cars traffic, house heating driven emissions and frequently subjected to canyon effects. The Air Heritage project in Portici, funded by the EU's Urban Innovative Actions (UIA) program, addressed these challenges by integrating low-cost sensors with traditional monitoring systems and engaging the community in pervasive measurement strategies. The project highlights the importance of individualized sensor calibration and frequent recalibrations to maintain accuracy. It also showcases the benefits of citizen science approaches, IoT infrastructures, AI components, and geostatistical sensor fusion algorithms for mobile and opportunistic air quality measurements. This paper reports on the lessons learned and experiences from the Air Heritage project, aiming to guide future implementations in similar contexts. By sharing these insights along with the gathered datalake, we aim to inform stakeholders, including researchers, public authorities, and citizens, about effective strategies for deploying and utilizing LCAQMS to enhance air quality monitoring and public awareness.

Shenzhen is China’s top ten clean air city and the cleanest air megacity. Even so, epidemiologic studies have shown ambient air pollution had significant adverse impacts on human health in this less polluted city. In this study, the concentrations of six criteria air pollutants (PM2.5, PM10, O3, NO2, SO2, and CO) from 2014 to 2017 were analyzed and compared to thresholds of both national and international air quality standards. The results showed concentrations of all air pollutants were below target values of current national air quality standard, but levels of particulate matter (PM) and O3 were still much higher than the recommended levels by the World Health Organization. Within national air quality standards, the number of over-limit days was rare with few variations between highly polluted and low pollution areas. The air quality improvement was slowing down recently. Our results suggest annual and daily thresholds for PM are too loose for air quality improvement in Shenzhen. Hence, we call for evaluation and establishment of tougher air quality standard.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

(1) Background: Environmental and public health research has given considerable attention to the impact of air quality on brain health, with systematic reviews widespread. No literature review has been done for cognitive frailty – a multidimensional syndrome combining physical frailty and cognitive impairment and their apparent co-dependence, linked to increased vulnerability and adverse health outcomes, including dementia. Instead, cognitive decline and frailty is implicitly explored through research on air quality and comorbid cognitive and physical decline in elderly populations. (2) Methods: A scoping review was conducted to explore the need for a systematic review. Combining Arksey and O’Malley [1] and PRISMA-ScR checklist [2], a scoping review of SCOPUS using ‘cogniti*’ + ‘resilience’ + ‘air quality’ or ‘cogniti*’ + ‘ageing’ + ‘air quality’ resulted in N=2503 articles, screened and reduced using inclusion and exclusion criteria, to N=16 articles. (3) Results: Air quality appears to be a critical risk factor for cognitive decline, even at air quality levels below WHO targets. Moderate long-term ambient air pollution appears linked to increased risk of cognitive frailty, suggesting earlier and more active interventions to protect older people. There are varied effects on cognition across the life course, with both emotional and functional impacts. Effects may be more detrimental to elderly people with existing conditions, including economic and health inequalities. Generalisation of results is limited due to the absence of a dose-response, variations in methods, controlling for comorbid effects, and variance across studies. (4) Conclusions: The findings support the need for more research and a more extensive summary of the literature.

The coronavirus disease (COVID-19) pandemic caused by spreading rapidly a severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has imposed a unique situation for the humanity. Sao Paulo has reported 124,105 confirmed cases of COVID-19 and 5,623 deaths up to June 14th, being considered the epicenter of the pandemic in Brazil and in South America. Due to the measures for social distancing, there was a drop in the air pollution concentration in Sao Paulo. Starting on March 16th, 2020, we broke 90 days of social distancing into 13 weeks and compared to an equivalent period in 2019. We investigated the air quality improvement during the quarantine period and compared the associated avoided deaths to COVID-19 burden deaths. Nitrogen dioxide (NO₂) was the best indicator of air quality in the analyzed weeks, since its reduction reached 58 %. Our study showed that the 5,623 deaths occurred during the analyzed weeks of quarantine represents an economic health loss of US$ 10.5 billion. In opposite, we observed a significant air quality improvement due to pollutants concentrations’ reductions during the analyzed weeks. Considering PM₁₀, PM_2.5 and NO₂, the decrease of concentration levels respectively avoided 78, 337 and 387 premature deaths and prevented up to US$ 1.5 billion on health costs. These results highlight the importance of continuing to enforce existing air pollution regulations and measures to protect human health both during and after COVID-19 pandemic.

Observing air quality from sensors onboard light rail cars in Salt Lake County, Utah began as a pilot study in 2014 and has now evolved into a five-year state-funded program. This metropolitan region suffers from both elevated ozone levels during summer and high PM2.5 events during winter. Pollution episodes result predominantly from local anthropogenic emissions but are also impacted by regional transport of dust, chemical precursors to ozone, and wildfire smoke as well as being exacerbated by the topographical features surrounding the city. Two electric light-rail train cars from the Utah Transit Authority light-rail Transit Express (“TRAX”) system were outfitted with PM2.5 and ozone sensors to measure air quality at high spatial and temporal resolution in this region. Pollutant concentration data underwent quality control procedures to determine whether the train motion affected the readings and how the sensors compared against regulatory sensors. Quality assurance results from data obtained over the past year show that TRAX Observation Project sensors are reliable, which corroborates earlier preliminary validation work. Two case studies from summer 2019 are presented to illustrate the strength of the finely-resolved air quality observations: 1) an elevated ozone event and 2) elevated particulate pollution resulting from 4th of July fireworks. The mobile observations were able to capture spatial gradients as well as pollutant hotspots during both of these episodes. Sensors have been recently added to a third light rail train car, which travels on a north-south oriented rail line along which we were unable to monitor air quality previously. The TRAX Observation Project is currently being used to provide reliable pollutant data for health studies and inform urban planning efforts. Links to real-time data displays and updated information on the quality-controlled data from this study are available at https://atmos.utah.edu/air_quality/trax/.

The effect of COVID-19 confinement regulations on air quality in the northwestern Alps is here assessed based on measurements at five valley sites in different environmental contexts. Surface concentrations of nitrogen oxides, ozone, particle matter, together with size, chemical, and optical (light absorption) aerosol properties, complemented by observations along the vertical column are considered. The 2020 concentration anomalies relative to previous years’ average are compared with the output of a machine learning algorithm accounting for weather effects and a chemical transport model, their difference being within 10–20 %. Even in the relatively pristine environment of the Alps, the «lockdown effect» is well discernible, both in the early confinement phase and in late 2020, especially in NOx concentrations (NO decreasing by >80 % and NO2 by >50 %). While ozone shows little variation, secondary aerosols increase due to enhanced transport from the neighbouring Po basin and coarse particles decrease due to missing resuspension by traffic and, in the city, to the shutdown of a steel mill. The NO2 vertical column density decreases by >20 %, whereas the aerosol profile is mainly influenced by large-scale dynamics, except a shallow layer about 500 m thick possibly sensitive to curtailed surface emissions.

Social distancing policies put in place during COVID-19 epidemic in addition to helping to limit the spread of the disease also contributed to improving urban air quality. Here we show a decrease in air pollutant concentration as a consequence of mobility reduction in São Paulo during the containment measure which began on 22^nd March 2020. When comparing to foregoing weeks to equivalent periods of 2019, the concentration of most air pollutants sharply decreased in the first days of mobility restriction, to then increase again after government officials downplayed the threat of the disease. This trend is also followed by a decrease in hospital admissions by SARS-influenza. Therefore, despite the great economic and social unrest caused by the pandemic, this unique situation shows that large-scale mobility reduction policy had a significant impact on air quality, benefiting, directly and indirectly, the public health system.

In the pursuit of energy efficiency and reduced environmental impact, adequate ventilation in enclosed spaces is essential. This study presents a hybrid neural network model designed for real-time monitoring and prediction of environmental variables. The system comprises two phases: An IoT hardware-software platform for data acquisition and decision-making, and a hybrid model combining short-term memory and convolutional recurrent structures. The results are promising and hold potential for integration into parallel processing AI architectures.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

Air quality has been a major concern throughout the world, Nigeria inclusive. The monitoring of air quality involves indoor and outdoor air quality. In this study, our concern was on indoor air quality. The aim of this study was to assess the air quality of residential homes (17), classrooms (3), hospitals (2), offices (5), Shops (2), and laboratories (5) in Akure, Nigeria in terms of formaldehyde (HCHO), total volatile organic compound (TVOC), Particulate matter (PM_1.0; PM_2.5, and PM₁₀). A Multifunction Air Detector was used for the assessment using the manufacturers’ procedures and the locations were identified using a Mini GPS. The results revealed as follows: HCHO (0.001-0.030 mg/m³), TVOC (0.003-362 mg/m³), PM_1.0 (004-014 µg/m³), PM_2.5 (006-020 µg/m³), and PM₁₀ (006-022 µg/m³). The results obtained were below the 24 h pollution recommended standards (0.1 mg/m³- HCHO; TVOC; 10-20 μ/m³ PM) of EPA and WHO. Statistically, there were correlations within the pollutants and weather. The Indoor air quality (IAQ) depicted the areas as ‘good,’ and toxicity potential (TP) were below unity. Although the locations looked safe, it is recommended that constant monitoring of the indoors should be ensured and proper ventilation should be provided.

This case study investigates the effects of ventilation intervention on measured and perceived indoor air quality (IAQ) in a repaired school where occupants reported IAQ problems. Occupants´ symptoms were suspected to be related to the impurities leaked indoors through the building envelope. The study’s aim was to determine whether a positive pressure of 5-7 Pa prevents the infiltration of harmful chemical and microbiological agents from structures, thus decreasing symptoms and discomfort. Ventilation intervention was conducted in a building section comprising 12 classrooms and was completed with IAQ measurements and occupants´ questionnaires. After intervention, the concentration of total volatile organic compounds (TVOC) and fine particulate matter (PM_2.5) decreased, and occupants´ negative perceptions became more moderate compared to those for other parts of the building. The indoor mycobiota differed in species composition from the outdoor mycobiota, and changed remarkably with the intervention, indicating that some species may have emanated from an indoor source before the intervention.

The air quality monitoring network in Alaska is currently limited to ground-based observations in urban areas and national parks leaving a large proportion of the state unmonitored. The use of MODIS aerosol optical depth (AOD) to estimate ground-level particulate pollution concentrations has been successfully demonstrated around the world, and could potentially be used in Alaska. In this work, MODIS AOD measurements at 550 nm were validated against AOD derived from AERONET ground-based sunphotometers in Barrow and Bonanza Creek to determine if MODIS AOD from the Terra and Aqua satellites could be used to estimate ground-level particulate pollution concentrations. The MODIS AOD was obtained from MODIS collection 6 using the dark target Land and Ocean algorithms from 2000 to 2014. MODIS data could only be obtained between the months of April and October; therefore, it could only be validated for those months. Individual and combined Terra and Aqua MODIS data were considered. The results showed that MODIS collection 6 products at 10 km resolution for Terra and Aqua combined are not valid over land but are valid over the ocean. On the other hand, the individual Terra and Aqua MODIS collection 6 AOD products at 10 km resolution are valid over land individually but not when combined. Results also suggest the MODIS collection 6 AOD products at 3 km resolution are valid over land and ocean and perform better over land than the 10-km product. These findings indicate that MODIS collection 6 AOD products can be used quantitatively in air quality applications in Alaska during the summer months.

Air pollution is a man-made environmental-related problem and has importance globally among all environmental issues. It is described as an atmospheric situation in which several components appear at high attention above their ambient level and generate a quantifiable effect on vegetation, animals, and people. Air pollution and its control are a universal problem and have become an issue of great trouble for us in current years. However, monitoring and measurement of the concentration of air pollutants are most difficult in assessment to monitoring other components in the environment. Air pollutants are transported to polar regions by different mechanisms such as long-range atmospheric transport or grasshopper effects and via anthropogenic activities. After reaching the polar regions, they settle down and remain as such for a long-time due to their persistent nature. They can distress the environment and wildlife of the polar regions. Generally, dangerous chemicals may cause a risk of well-being effects, whereas lethal pollutants focus on one physiological reaction. We reviewed the available information on air pollution (occurrence, sources, and harmful effects) in the polar regions.

This study investigates the characteristics of formaldehyde (HCHO) concentration and its reduction in newly constructed apartment buildings in Dubai. It addresses the significant health risks of high HCHO levels due to poor ventilation and extensive use of VOC-emitting materials. The research explores the effectiveness of various mitigation strategies, including air purifiers, photocatalyst applications, and window ventilation, in the living room, master bedroom (MBR), Room 1, and Room 2. HCHO concentrations were measured under different conditions: sealed windows, operation of an air purifier with a VOCs filter, and the application of a photocatalyst. The study followed a quantitative approach, recording real-time HCHO levels over 24 hours. Results indicated that sealing windows led to HCHO concentrations surpassing the domestic standard of 0.1 ppm, with the MBR recording the highest concentration at 0.73 ppm. The air purifier showed minimal impact within the first 8 hours but achieved an 18% reduction after 24 hours of operation. Applying a photocatalyst to room surfaces resulted in a 50% reduction in HCHO levels. Ventilation through window openings significantly improved air exchange rates, with the air exchange per hour (ACH) increasing proportionally with window opening size. Smaller rooms with larger window-to-volume ratios, such as Room 1 and Room 2, maintained HCHO concentrations below the WHO standard of 0.1 ppm with partial window openings. The study concludes that window ventilation is the most effective strategy for reducing HCHO concentrations, highlighting the importance of integrating comprehensive ventilation designs in modern residential buildings to ensure healthier indoor environments in Dubai.

This paper examines the impact of renewable energy heating on air quality in northern China, using the Qinling Mountains-Huaihe River line as a quasi-natural experiment to distinguish between regions with central heating and those without. Employing a difference-in-differences approach and analyzing panel data from 299 cities between 2014 and 2022, our findings indicate that the renewable energy heating policy has significantly improved air quality. Specifically, the policy led to substantial reductions in the Air Quality Index (AQI) and concentrations of key pollutants: SO2 by 28.31%, CO by 7.57%, NO2 by 5.72%, and PM2.5 by 7.15%. The policy's effects are most pronounced in regions with lower temperatures and in the eastern parts of the country. Further analysis emphasizes the critical role of energy transition, environmental regulations, and government investment in technology as key drivers of these air quality improvements.

The rural communities are affected by gaseous emissions from intensive livestock production. Practical mitigation technologies are needed to minimize emissions from stored manure and improve air quality inside barns. In our previous research, the one-time surficial application of biochar to swine manure significantly reduced emissions of NH3 and phenol. We observed that the mitigation effect decreased with time during the 30-day trials. In this research, we hypothe-sized that bi-weekly reapplication of biochar could improve the mitigation effect on a wider range of odorous compounds using larger scale and longer trials. The objective was to evaluate the effectiveness of biochar dose and reapplication on mitigation of targeted gases (NH3, odor-ous VOCs, odor, GHGs) from stored swine manure on a pilot-scale setup over 8-weeks. The bi-weekly reapplication of the lower biochar dose (2 kg/m2) showed much higher significant percent reductions of emissions for NH3 (33% without & 53% with reapplication) and skatole (42% without & 80% with reapplication), respectively. In addition, the reapplication resulted in the emergence of statistical significance to the mitigation effect for all other targeted VOCs. Spe-cifically, for indole, the % reduction improved from 38% (p=0.47, without reapplication) to 78% (p=0.018, with reapplication). For phenol, the % reduction improved from 28% (p=0.71, without reapplication) to 89% (p=0.005, with reapplication). For p-cresol, the % reduction improved from 31% (p=0.86, without reapplication) to 74% (p=0.028, with reapplication). For 4-ethyl phenol, the percent emissions reduction improved from 66% (p=0.44, without reapplication) to 87% (p=0.007, with reapplication). The one-time 2 kg/m2 and 4 kg/m2 treatments showed similar effectiveness in mitigating all targeted gases, and no statistical difference was found between the dosages. The one-time treatments showed significant % reductions of 33% & 42% and 25% & 48% for NH3 and skatole, respectively. The practical significance is that the higher (one-time) biochar dose may not necessarily result in improved performance over the 8-week manure storage, but the bi-weekly reapplication showed significant improvement in mitigating NH3 and odorous VOCs. The lower dosages and the frequency of reapplication on the larger-scale should be explored to optimize biochar treatment and bring it closer to on-farm trials.

Ukraine is an associate member of the European Union and in the coming years it is expected that all the data and services already used by European Union countries will become available for Ukraine. An important program, which is the basis for building European monitoring services for Smart Cities, is the Copernicus program. The two most important services of this program are Copernicus Land Monitoring Service (CLMS) and Copernicus Atmosphere Monitoring Service (CAMS). CLMS provides important information on Land Use in Europe. In the context of Smart Cities, the most valuable one is the Urban Atlas service, which is related to local CLMS services and provides a detailed digital city plan in vector form, which is segmented into small functional areas classified by the CORIN nomenclature. The Urban Atlas is a geospatial layer with high-resolution, which is built for all European cities with a population of more than 100,000 that combines high-resolution sat-ellite data, city segmentation by blocks and functional areas, important city infrastructure, etc. This product is used as a basis for city planning and obtaining analytics on the most important indicators of city development including air quality monitoring. For Ukraine, such geospatial products are not provided under the Copernicus program. It is important to start work on its development and implementation as early as possible, so that when the first city atlas appears, Ukraine will be ready to work with it together with the European community. This requires preparing the basis for na-tional research and training national stakeholders and users to use this product. To make this happen it’s necessary to have national geospatial product, which can be used as an analogue of the city atlas. In this article authors analyzed the existing methods of air quality assessment and assessment of the SDG indicator 11.6.2 achieving for European cities, based on which the indicator 11.6.2 for Ukraine for 5 years was evaluated for the first time. The obtained results are analyzed and the values of indicator 11.6.2 for Ukraine are compared with European countries.

This paper describes a case study of ventilation as well as measured and perceived indoor air quality (IAQ) in a Finnish comprehensive school with a hybrid ventilation system and reported IAQ problems. An operational error was found when investigating the ventilation system that prevented air from coming into classrooms, except for short periods of high carbon dioxide (CO₂) concentrations. However, results indicated that hybrid ventilation system was able to provide adequate ventilation and sufficient IAQ once properly designed and maintained. After ventilation operation was improved, occupants reported less unpleasant odors and stuffy air. The amount of total volatile organic compounds (TVOC) and some single volatile organic compounds (VOCs) decreased. Indoor mycobiota was observed in settled dust in the classrooms, from which ventilation improvement eliminated the dominant, opportunistic human pathogen species Trichoderma citrinoviride found before improvement.

The ambient air quality data for particulate matter as well as criteria of gaseous pollutants were assembled during December 2013 to December 2015 from the Continuous Air Quality Monitoring Station (CAMS) located at Agrabad, Chittagong. The observation showed that during April- October, 24 hour average concentration of PM10 and PM2.5 were within the National Ambient Air Quality Standard (NAAQS) level but it increased occasionally by more than two and a half times during the whole non-monsoon period (November-March). The highest values found of PM2.5 were 321.1 µg/m³ in January, 2013 and 220.34 µg/m³ in December 2015. Whether, the highest alarming concentration of PM10 was reported as 474 µg/m3 in January 2007. The other gaseous pollutants such as SO₂, NO₂, O₃, CO and Hydrocarbons remain well within the permissible limit except dry non-monsoon period. The yearly average increase of Air Quality Index (AQI) value indicates the growth rate of air pollution in Chittagong city. The main responsible pollutant for air pollution is found PM_2.5.

Research have been conducted in many countries around the world to assess air quality during COVID-19 pandemic, especially during lockdown period, some of these studies found an increase or decrease in some pollutants. This paper investigates the impact of COVID-19 on seven air pollutants (i.e., PM_2.5, PM₁₀, NO₂, O₃, SO₂, H₂S, CO) from the period January 2020 to December 2020 in the State of Kuwait. Kuwait is a desert country located in the north-eastern part of the Arabian Peninsula, and the northeast of the Arabian Gulf (Persian as it is sometimes called). Several analytical methods were conducted, such as spatial analysis (spatial interpolation) to study the distribution of the studied variables. The data was also statistically analysed (time series analysis - Kernel density) to study the temporal changes. The analysis also included applying air quality index to the data. We found that concentrations for the pollutants decreased during the pandemic due to the decrease of anthropogenic sources including such as traffic and petroleum activities, but the concentration for PM_2.5 increased, mostly because of the transported dust coming with the northwest winds prevailing in Kuwait from the Arabian deserts and Iraq.

In this paper, we tackle air quality forecasting by using machine learning approaches to predict the hourly concentration of air pollutants (e.g., Ozone, PM_2.5 and Sulfur Dioxide). Machine learning, as one of the most popular techniques, is able to efficiently train a model on big data by using large-scale optimization algorithms. Although there exists some works applying machine learning to air quality prediction, most of the prior studies are restricted to small scale data and simply train standard regression models (linear or non-linear) to predict the hourly air pollution concentration. In this work, we propose refined models to predict the hourly air pollution concentration based on meteorological data of previous days by formulating the prediction of 24 hours as a multi-task learning problem. It enables us to select a good model with different regularization techniques. We propose a useful regularization by enforcing the prediction models of consecutive hours to be close to each other, and compare with several typical regularizations for multi-task learning including standard Frobenius norm regularization, nuclear norm regularization, ℓ_2,1 norm regularization. Our experiments show the proposed formulations and regularization achieve better performance than existing standard regression models and existing regularizations.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

The increasing demand for water resources in urban areas, such as Bangladesh, due to population growth is a significant concern. One potential solution under consideration is the use of air conditioning (AC) condensate water. A study conducted at the European University of Bangladesh (EUB) focused on assessing the quality and quantity of AC condensate water from various systems. The results indicate that the collected water generally adhered to the quality standards established for drinking and household use in Bangladesh. Parameters such as pH (averaging 6.8), turbidity (1.08 NTU), total dissolved solids (TDS) (averaging 219 mg/L), iron content (0 mg/L), alkalinity (averaging 41.67 mg/L), arsenic (0 mg/L), chemical oxygen demand (COD) (averaging 3.67 mg/L), biochemical oxygen demand (BOD) (averaging 1.33 mg/L), chloride content (averaging 30.77 mg/L), and other factors were evaluated. Moreover, the AC units at EUB, varying in cooling capacity (1 ton, 2 tons, and 4 tons), produced substantial monthly volumes of 96, 177, and 354 liters of condensate water, respectively. This underscores the potential of AC condensate water as a valuable resource for addressing urban water scarcity. As a result, there is a pressing need for local decision-makers and policymakers to establish well-defined guidelines for the effective utilization of AC condensate water to mitigate water scarcity issues in urban areas.

Air quality is one of the most concerning problems in major industrialized cities in the world. Prediction of future air quality is highly relevant to public health. In some big cities, multiple air quality measurement stations are deployed at different locations to monitor air pollutants, such as NO2, CO, PM 2.5 and PM 10, over time. At every monitoring time stamp t, we observe one station×feature matrix xt of the pollutant data, which represents a spatio–temporal process. Traditional methods on prediction of air quality typically use data from one station or can only predict a single pollutant (such as PM 2.5) at a time, which ignores the spatial correlation among different stations. Moreover, the air pollution data are typically highly nonstationary, We propose a de-trending graph convolutional LSTM (long short term memory) to continuously predict the whole station×feature matrix in the next 1 to 48 hours, which not only captures the spatial dependency among multiple stations by replacing an inner product with convolution, but also incorporates the de-trending signals (transform a nonstationary process to a stationary one by differencing the data) into our model. Experiments on the air quality data of the city Chengdu and multiple major cities in China demonstrate the feasibility of our method and show promising results.

Traffic congestion is one of the foremost problems confronted by the urban and suburban tenants of today. Traffic congestion increases vehicle emissions and degrades air quality. Urban planners and policy makers have consequently been always investigating choices to alleviate traffic congestion and to enhance air quality. Teleworking is one option that has received significant consideration and has been studied in the recent past. The aim of the study is to explore the relationship between teleworking, air quality and traffic in Switzerland. The analysis relies on panel individual and household level data over the period 2002-2013. We examine five main air pollutants; the sulphur dioxide (SO₂), the ground-level ozone (O₃) the nitrogen dioxide (NO₂), the carbon monoxide (CO) and the particulate matter less than 10 microns (PM₁₀). Based on the fixed effects estimates, teleworking reduces traffic volume by 1.9 per cent. Furthermore, the reduction observed on air pollution is higher for NO₂, CO and PM₁₀ ranging between 3.3-3.7 per cent, followed by O₃ at 2.3 per cent and SO₂ at 2.1 per cent. According to instrumental variable (IV) approach and the two stage least squares (2SLS) method, the effect is higher ranging between 2.6-4.1 per cent. The respective reduction on traffic becomes 2.7 per cent. Overall, the main concluding remark of the study is that teleworking can be a promising tool for urban planning and development, focusing at the traffic volume reduction, and the air quality improvement. Additional policy implications of teleworking and its beneficial effects for the society are further discussed.

This document serves as supplemental information to Shapero et al. (2023), which is itself a comment on Nowell et al. (2022). Environmental Health Perspective’s publishing standards for article comments have strict word counts and do not allow the addition of new primary data analyses; therefore, this document provides an additional level of detail and supporting analyses that serve as an important backup to and expansion of Shapero et al. (2023) and that also respond to some comments within the author’s reply to our comments (Holmes and Nowell, 2023). Nowell et al. (2022) evaluated potential PM_2.5 community impacts from sugarcane harvesting. However, their analysis is flawed by erroneous assumptions and misapplied technical approaches, as discussed in Shapero et al. (2023) and as detailed in this supplemental information document. Additionally, the authors ended their analysis with 2018 data, but later data shows no marginal increase in PM_2.5 during sugarcane harvest following 2019 even using the authors’ approach (Holmes and Nowell, 2023). Therefore, the authors’ evaluations have no relevance to current conditions. Nonetheless, even their evaluation and conclusions regarding PM_2.5 concentrations purportedly attributable to sugarcane harvesting prior to 2019 are unsupported and technically unsound as detailed below.

Asthma is a chronic respiratory disease that impairs breathing. Management of asthma presents a significant challenge due to its inherent variability; that is, its symptoms can substantially differ among individuals, thereby complicating the prediction and management of exacerbations. Furthermore, individuals with asthma often have unique triggers that precipitate symptoms or attacks. The identification of these triggers can often prove to be a challenging, and at times, an impractical attempt. To address this, our research proposes a practical, personalized alert system, predicated on individual lung function tests conducted under varying environmental conditions classified by air-quality sensors. To validate this concept, we conducted an observational pilot study involving healthy individuals. We recruited twelve healthy participants and monitored their responses across a broad spectrum of environments, characterized by varying air quality, temperature, and humidity conditions. The lung function for each participant, assessed using peak expiratory flow (PEF) values, was recorded in each of these environments. Our results highlighted substantial variability in pulmonary responses to different environments. Utilizing these insights, we proposed a personalized alarm system that provides real-time air-quality monitoring and issues alerts when environmental conditions may potentially become unfavorable. We also explored the feasibility of employing basic machine learning techniques to predict PEF values in the aforementioned environmental conditions. This proposed system has the potential to empower individuals in actively safeguarding their respiratory health and mitigating discomfort caused by environmental conditions, especially in cases of asthma patients. By enabling timely and personalized interventions, the system aims to provide individuals with the necessary tools to minimize exposure to asthma’s possible triggers.

The increase and diversity of low-cost Air Quality (AQ) sensors, as well as their flexibility and low power consumption, offers us the opportunity to integrate them into a broad AQ wireless sensor networks with the aim of enabling real-time monitoring and higher spatial sampling density of pollution in all parts of the cities. Considering that the vast majority of the population lives in these cities and the increase in respiratory/allergic problems in a large part of the population, it is of great interest to offer services and applications to improve their quality of life. In the ECO4RUPA project we focus on this kind of service, proposing an inclusive and intelligent routing ecosystem carried out by using a network of low-cost AQ sensors with the support of 5G communications along with official AQ monitoring stations, assisted with artificial intelligence to improve the AQ monitoring data and by spatial interpolation techniques to enhance its spatial resolution. The goal of this service is to calculate healthy walking and/or cycling routes according to the particular citizen’s profile and needs. We provide and analyse the results of the proposed route planner under different scenarios (different time tables, congestion road traffic and routes) and different user’s profiles, with special interest on citizens with asthma and pregnant women, since both require special needs. In summary, our approach can lead to an approximately average reduction in pollution exposure of 17.82%, while experiencing an approximately average increase in distance travelled of 9.8 %.

In this article, we aim to show the capabilities, benefits, as well as restrictions, of three different air quality-related information sources, namely the Sentinel-5Precursor TROPOspheric Monitoring Instrument (TROPOMI) space-born observations, the Multi-Axis Differential Optical Absorption Spectroscopy (MAX-DOAS) ground-based measurements and the LOng Term Ozone Simulation – EURopean Operational Smog (LOTOS-EUROS) chemical transport modelling system simulations. The tropospheric NO2 concentrations between 2018 and 2021 are discussed as air quality indicators for the Greek cities of Thessaloniki and Ioannina. Each dataset was analysed in an autonomous manner and, without disregarding their differences, the common air quality picture that they provide is revealed. All three systems report a clear seasonal pattern, with high NO2 levels during winter-time and lower NO2 levels during summer-time, reflecting the importance of photochemistry in the abatement of this air pollutant. The spatial patterns of the NO2 load also showed, in both space-born observations and model simulations, the undeniable variability of the NO2 load within the urban agglomerations. The diurnal variability was furthermore clearly identified by the ground-based measurements, which also unquestionably revealed a Sunday minimum NO2 load effect, alongside the rest of the sources of air quality information. Within their individual strengths and limitations, the space-born observations, the ground-based measurements and the chemical transport modelling simulations, demonstrate unequivocally their ability to report on the air quality situation in urban locations.

Warsaw is among European cities with the worst atmospheric air quality, mainly due to very high pollution emitted by the residential sector and road traffic. This results in high concentrations of particulate matter and nitrogen oxides, often exceeding WHO standards. The paper discusses the current and expected effects of actions taken by the Warsaw authorities, to significantly improve air quality in the city. The Clean Air Program currently implemented mainly involves the reduction, and ultimately the total elimination, of coal combustion in all heat sources of the municipal sector, which is identified in numerous publications as the main source of air quality degradation in cities. The program's goal, which timeframe covers the years 2018-2029, is a definite reduction in particulate pollution. The second part of the remedial activities, covering the years 2024-2034, mainly concerns the reduction of nitrogen oxide pollution, the main source of which is urban road traffic. In the latter case, the expected effects of introducing Low-Emission Zone (launched July 2024) in the city center are considered. According to the project, the zone's implementation will consist of five two-year stages, in which the car emission limits will gradually tighten. The paper compares the effectiveness of two being considered versions, differing in size zones.

Studies carried out have revealed that every day around three thousand and twelve people lose their lives in the world due to traffic accidents and poor air quality. Large cities, with their millions of inhabitants and vehicles, face many problems relating to vehicular traffic. In 2015 the speed limit was modified on several roads in the city of São Paulo-Brazil. However, in 2017 the speed limits were increased again, but not on all previous routes. This study analyzed the impact of this change on the number of accidents and pollutant concentrations, over a period of ten years, comparing the periods before and after the implementation of the measure, using real data collected and provided by the authorities of the city and the state transit and environmental companies, on more than forty routes and two nearby air quality stations. The results show a clear reduction in the number of accidents without victims on the roads of the city of São Paulo starting in 2010. However, the restrictive measures imposed by government officials may have contributed to the decrease in the number of accidents, but the number of fatalities has not changed much. Air pollution has not improved substantially with speed changes, as new speed increases have been linked to new episodes of congestion. The average number of fatalities due to accidents has been increasing since 2010 and accidents are becoming more serious. The application of a general linear statistical model (GLM) estimated the impact of the speed reduction policy in terms of the number of injuries avoided per month: 43.4 and 14.1 on other roads and on Pinheiros marginal, respectively. The results highlight the need for a constant data collection by the authorities in cities with high vehicle traffic. The important temporal time trend in terms of reduction of injuries but not in terms of fatalities and air quality, shows the need to apply joint public policies, not only speed reduction, but also the use of new technologies and raising drivers’ awareness of the problem.

Keywords:

Air quality and environmental fairness have always been an area of prime interest across the globe. The significance low-cost air quality sensing and practices spikes during the time of pan-demic and epidemics when the air becomes a threat to living beings especially human beings. The gradual innovation and enrichment in low-cost air quality sensing sensors, nodes or devices, and systems are exponentially increasing for the last three decades. This work reviews the major contributions in a) low-cost scalable air quality assessment; b) low-cost air quality sensors, sensing approaches and technologies; c) low-cost state-of-the-art gas sensors fabrication methods (MEMS and CMOS); d) low-cost gas sensors measurement configurations and assemblies; and e) low-cost air quality sensors calibration and testing systems. A systematic review of past work with a goal to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies has been rendered in this work. Starting from sensors electrodes to IoT based mobile smart nodes; all have been introduced in this article.

After the arrival of a new airborne virus to the world, science is aiming to develop solutions to withstand the spread and contagion of the SARS-CoV-2 coronavirus. The most severe among the adopted measures is to remain in home isolation for a significant number of hours per day, in order to avoid the spreading of the infection in an uncontrolled way through public spaces. Recent literature showed that the major route of transmission is via aerosols produced especially in poorly ventilated inner spaces. With regard to contagion rates, accumulated incidence or number of hospitalizations due to COVID-19, Spain has reached very high levels, therefore this article develops a quantitative and qualitative analysis of the requirements established in Spain with respect to the European framework in reference to ventilation parameters indoors. For this, a case study has been analyzed, representing a common residence in current Spanish residential developments. Results show that the criteria established in the applicable regulations are not sufficient to ensure health as well as to avoid contagion by aerosols indoors.

This paper describes the indoor air pollution in urban (Lahore, Faisalabad, Gujranwala, Rawalpindi and Karachi) Pakistani regions while considering the outdoor air and the health and wellbeing of the occupants present indoors. It also aims to assess previous methodological approaches Such as Air Conditioning Systems, used by developed countries to improve air quality to demonstrate the improvements that can be made in air quality in Pakistani urban areas. This research also investigates the causes, concentration and effects of poor air quality in Pakistani urban areas such as particulate matter (PM2.5), carbon oxides (COx), nitrogen oxides (NOx), sulphur oxides (SOx) and volatile organic compounds (VOC’s). The average concentration of these pollutants in Pakistan’s indoor air is, particulate matter (PM): [100 – 250 µg/m3 for PM2.5, 200 – 600 µg/m3 for PM10] 1 – 20 ppm for carbon monoxide (CO), nitrogen oxides (NOx): [50 – 100 µg/m3 for NO2, 20 – 40 µg/m3 for NO], 20 – 50 µg/m3 for sulfur dioxide (SO2), volatile organic compounds (VOCs): 0.1 – 0.5 ppm for formaldehyde, 5 – 10 µg/m3 for benzene and 20 – 30 µg/m3 for toluene. It should be noted that these concentrations can differ depending on the origin of pollution, location, and time of day. The literature review is made up of a combination of descriptive research methods that are used to inform the research background of ambient and indoor air quality, thus the literature review provides a theoretical and methodological background about the air pollution and its improvement in different parts of the world. According to the World Air Quality Index, Pakistan is the third most polluted country in terms of average PM2.5 concentration which is 14.2 times the WHO annual air quality guideline value. As a result, it is suggested that a PM2.5 concentration reduction program be implemented in urban Pakistani regions' indoor air.

International literature data report that the increase of infectious risk may be due to heating, ventilation and air conditioning (HVAC) systems contaminated by airborne pathogens. Moreover, the presence of complex rotating dehumidification wheels (RDWs) may complicate the cleaning and disinfection procedures of the HVAC systems. We evaluated the efficacy of a disinfection strategy applied to the RDW of two hospitals HVAC systems. Hospitals have 4 RDW systems related to the surgical areas (SA1 and SA2) and to the intensive and sub-intensive cares (IC and sIC). Microbiological air and surfaces analysis were performed in HVAC systems, before and after the disinfection treatment. Hydrogen peroxide (12%) with silver ions (10 mg/L) was aerosolized in all the air sampling points, located close to the RDW device. After the air disinfection procedure, reductions of total microbial counts at 22°C and fungi were achieved in SA2 and IC HVAC systems. An Aspergillus fumigatus contamination (6 CFU/500L), detected in one air sample collected in the IC HVAC system, was eradicated after the disinfection. Surface samples proved a good microbiological quality. Results suggest the need of a disinfection procedure aimed to improve the microbiological quality of the complex HVAC systems, mostly in surgical and intensive care areas.

This study provides a thorough review and analysis of the evolution of the Greek vehicle fleet over the last ~30 years, which is next used for the generation of high granularity fleet projections and for the estimation of relevant environmental benefits by 2030. The integrated methodology developed takes also into account vehicle clustering and the Brown’s Double Simple Exponential Smoothing technique that together with the adoption of COPERT based emission factors allow for the estimation of the anticipated emissions in 2030. Expected 2030 emissions levels suggest a reduction across all pollutants in comparison to 2018, ranging from 3.7% for PM10 to 54.5% for NMVOC (and 46% for CO, 14% for SO2, 28% for NOX and 21% for CO2). We find that Greece is on track with national goals concerning the reduction of air pollution from the transportation sector, stressing the positive contribution of EVs and new, "greener" vehicles, and setting new challenges for the further improvement of the sector beyond the 2030 outlook.

Since people spend most of their time in indoor environments, the objective of this work was to study indoor air quality perception and its effects on users’ thermal comfort. Based on previous data from a building with a central air-conditioning system and two mixed-mode buildings located in the humid subtropical climate of Florianópolis, southern Brazil, statistical analyses were performed. Each user subjective answer obtained through a questionnaire was combined with the corresponding environmental conditions – measured using microclimate stations, a portable thermo-anemometer and a CO2 analyser. Results showed that improvement in air quality was associated with the reduction of air temperature and humidity ratio. Also, there was a significant influence of thermal, air movement and humidity sensation and acceptability of air quality perception. Users felt more satisfied or neutral with air quality for being in thermal comfort, and not because of the CO2 level – which means that air quality perception is influenced by factors other than CO2. This study recommends the implementation of an air exchange device in split air-conditioners with air recirculation used in mixed-mode buildings in Brazil. It is important to provide suitable indoor ventilation to reduce pollutants concentration, ensure good air quality and prevent respiratory diseases.

High levels of air pollution can contribute to high rate of the COVID-19 outbreaks. Air pollutants induce oxidative stress, inflammatory process, immune imbalance and coagulation at systemic level, making the organism susceptible to complications caused by various pathogens, including viruses, resulting in a possible important damage co-factor. Sperm cells are highly sensitive to the pro-oxidant effects of environmental pollutants, and may represent an important alarm bell indicating that the burden of environmental pressure in a certain area is causing damage to humans. A comparison of the maps of COVID-19 case fatality rates, male infertility rates and air pollution may suggest a way to understand the dynamics of the virus impact. Semen quality may be considered as an early and sensitive environmental marker, and also a potential susceptibility indicator to viral insults (including SARS-CoV-2 ) in heavily polluted areas. Therefore, assessing the burden of environmental exposure of a given population and its potential susceptibility to insults through early biological stress indicators may be helpful for predicting the risk of the adverse effects by the SARS-CoV-2 epidemic .

Market air quality is very important to the economic lives of the people which is rarely researched, however, market activities particularly pedestrian traffic releases particulates which is detrimental to the health of the users and stakeholders. Thermo scientific MIE pDR-1500 particulate was used to monitor the quality of air within the market for eight (8) weeks, air pollutant of concern is PM2.5. ten (10) sample points were located in the market which covers ten (10) sample points for pedestrian traffic to represent the entire market environment spectrum. The analysis of PM2.5 measured daily during dry and wet season shows a clear seasonal variation of this particular pollutant as elevated concentration was measured during the dry season than the wet season. The assessment of PM2.5 concentration shows exceedances of the standards stated by WHO and NAAQS during the dry season which ranges from 47.9 μg/m3- 231.88 μg/m3 in the morning and 65.17 μg/m3- 1806.33 μg/m3 in the afternoon. From the findings, pedestrian traffic contributes immensely to air pollution in an open market, with this elevated concentration, prolonged exposure is highly detrimental to health. This study creates awareness to the pedestrians in an open market about air pollution and informs policy changes.

The ongoing COVID-19 global pandemic is affecting every facet of human lives (e.g., public health, education, economy, transportation, and the environment). This novel pandemic and citywide implemented lockdown measures are affecting virus transmission, people’s travel patterns, and air quality. Many studies have been conducted to predict the COVID-19 diffusion, assess the impacts of the pandemic on human mobility and air quality, and assess the impacts of lockdown measures on viral spread with a range of Machine Learning (ML) techniques. This review study aims to analyze results from past research to understand the interactions among the COVID-19 pandemic, lockdown measures, human mobility, and air quality. The critical review of prior studies indicates that urban form, people's socioeconomic and physical conditions, social cohesion, and social distancing measures significantly affect human mobility and COVID-19 transmission. During the COVID-19 pandemic, many people are inclined to use private transportation for necessary travel purposes to mitigate coronavirus-related health problems. This review study also noticed that COVID-19 related lockdown measures significantly improve air quality by reducing the concentration of air pollutants, which in turn improves the COVID-19 situation by reducing respiratory-related sickness and deaths of the people. It is argued that ML is a powerful, effective, and robust analytic paradigm to handle complex and wicked problems such as a global pandemic. This study also discusses policy implications, which will be helpful for policymakers to take prompt actions to moderate the severity of the pandemic and improve urban environments by adopting data-driven analytic methods.

We developed an artificial neural network as an air quality model and estimated the scope of the impact of climate change on future (until 2064) summertime trends of hourly Ozone (O3) concentrations at an urban air quality station in Tehran, Iran. Our developed scenarios assume that present-time emissions conditions of O3 precursors will remain constant in the future. Therefore, only the impact of climate change on future O3 concentrations is investigated in this study. GCM projections indicate more favorable climate conditions for O3 formation over the study area in the future: the surface temperature increases over all months of the year, solar radiation increases, and precipitation decreases in future summers, and summertime daily maximum temperature increases about 1.2 ∘C to 3 ∘C until 2064. In the scenario based on present-time O3 conditions in 2012 summer without any axceedances, the summertime exceedance days of 8-hr O3 standard are projected to increase in the future by about 4.2 days in the short term and about 12.3 days in the mid-term. Similarly, in the scenario based on present-time O3 conditions in 2010 summer with 58 days of exceedance from 8-hr O3 standard, exceedances are projected to increase about 4.5 days in the short term and about 14.1 days in the mid-term. Moreover, the number of Unhealthy and Very Unhealthy days in 8-hr AQI is also projected to increase based on pollution scenarios of both summers.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Multiple social and environmental justice concerns are linked to urban form such as the distribution of socioeconomic class populations, healthcare spending, air pollution exposure, and human mobility. This study used 1m resolved LIDAR data to characterize land use in Salt Lake County, Utah and associate it with sociodemographic and air quality data at the census block group and zip code levels. We found that increasing tree cover was associated with higher per capita income and lower minority populations while increasing built cover was linked to lower per capita income and higher minority populations. Air quality showed less strong correlations, however, decreased non irrigated cover, increased built cover, and higher amounts of households living under poverty was related to higher long-term PM2.5 exposure. Several policy efforts have been undertaken to improve air quality and reduce negative health outcomes in Utah which are being informed by regulatory and research grade air quality sensors.

Background: Recent studies suggest an association between long-term air pollution, diet, and health outcomes, but there are limited studies on how short-term air pollution affects dyslipidemia in particular. We aimed to investigate this association with modified fruit and vegetable consumption.Methods: The Cardiovascular Disease Association Study (CAVAS) included 8,779 participants between 2007 and 2016. Particulate matter (PM_2.5) and nitrogen dioxide (NO₂) levels were estimated using community multiscale air quality models. Short-term air pollution exposure was defined as a moving average over a lag time from “lag 1 days” to “lag 14 days.” Fruit and vegetable intake was categorized into 'total vegetables (TV),’ 'non-salted vegetables (NSV),' 'salted vegetables (SV),' 'fruits (F),' 'non-salted vegetables + fruits (NSVF),' and 'total vegetables + fruits (TVF).' Dyslipidemia was defined by total cholesterol ≥240 mg/dl, LDL cholesterol ≥160 mg/dl, HDL cholesterol <40 mg/dl, serum triglycerides ≥200 mg/dl, or physician-reported dyslipidemia.Results: Higher short-term PM_2.5 concentrations were associated with an increased risk of dyslipidemia (odds ratio (OR) = 1.012, 95% CI: 1.003, 1.020 for a lag of 14 days). High PM_2.5 groups (≥23.3 μg/m³) with a higher TV intake (≥186.1 g/day) were associated with a decreased risk of dyslipidemia (OR = 0.88, 95% CI: 0.78, 0.99). Additionally, high PM_2.5 groups (≥23.3 μg/m³) with a higher intake of SV (≥110.6 g/day) were associated with a decreased risk of dyslipidemia (OR = 0.86, 95% CI: 0.76, 0.97). Conclusion: Our study suggests that vegetable consumption is an important dietary factor for attenuating risk of dyslipidemia associated with short-term air pollution exposure.

Air change rate is an important parameter for quantification of ventilation heat losses and also affects the indoor climate of buildings. Indoor air quality is significantly associated with ventilation. If air change isn't sufficient, trapped allergens, pollutants and irritants can degrade the indoor air quality and affect the well-being of a building's occupants. Many studies on ventilation and health have concluded that lower air change rates can have a negative effect on people’s health and low ventilation may result in an increase in allergic diseases. Quantification of air change rate is complicated, since it is affected by a number of parameters, of which the one of the most variable is the air-wind flow. This study aims to determination and comparison of values of the air change rate in two methods - by quantifying of aerodynamic coefficient Cp = Cpe - Cpi – so called aerodynamic quantification of the building and the methodology based on experimental measurements of carbon dioxide in the selected reference room in apartment building.

Air pollution is a leading cause of death in the United States, and is associated with adverse health outcomes, including increased vulnerability to coronavirus disease 2019 (COVID-19). The AirBeam2 was used to measure particulate matter with a diameter of 2.5 micrometers or smaller (PM2.5), to investigate differences between indoor and ambient levels at seven private homes in New York during and after the COVID-19 lockdown. Measurements taken in 2020 winter, spring and fall and in fall 2022 showed that 90% of the time, indoor PM2.5 levels exceeded outdoor levels both during and after the COVID-19 lockdown, p = 0.03, and exceeded safety levels. Higher indoor PM2.5 levels attributed to little or no ventilation from cooking and smoke in the kitchen and basements, were significantly greater in fall than in winter. Higher ambient PM2.5 levels were attributed to vehicular traffic at a street-facing sampling site. PM2.5 sources identified in this study may help in devising control strategies to improve indoor air quality (IAQ), and consequently alleviate respiratory health effects. These findings may be used as a basis for in-house modifications including natural ventilation and use of air purifiers to reduce exposures, mitigate future risks, and prevent potential harm to vulnerable residents.

PDMS samples may be used in various microfluidic applications by hydrophilizing their surfaces. This study examines the effects of air plasma jet (APJ) and dielectric barrier discharge (DBD) plasma on the surface hydrophilicity of polydimethylsiloxane. In order to increase the hydrophilicity of PDMS sample surfaces, two plasma sources including APJ and DBD were compared. Both DBD and APJ setups were measured for voltage and current, and their respective power was calculated and compared based on their characteristics. It is important to note that the electrical specifications of APJ and DBD were identical, and the source power rates for APJ and DBD plasma were 306W and 300W respectively. UV-vis spectroscopy was used to characterize the plasma, and an electrical characterization of the plasma's power supply was carried out. The effects of parameters such as the distance from the nozzle tip, the duration of the process, and the source voltage on the hydrophilicity of the surfaces during the treatment by APJ were also examined, and samples were then examined for a period of time to determine whether surface hydrophilicity was preserved. On the PDMS surface, a contact angle of about 5.1° was observed using short-term plasma treatments of 10 seconds. In the same conditions, the effect of DBD treatment was superior to that of APJ treatment.

Despite air pollution being a leading cause of health issues in developing nations, public awareness and understanding of local air quality remains notably low. The present study assesses the perception, attitude, and environmental knowledge of local air pollution among adult urban residents (n=870) in a city with leading air pollution rates among cities of emerging economies: Astana, Kazakhstan. Structural equation modeling (SEM) was employed to investigate the causal relationship between perceived air quality, environmental literacy, and willingness to pay (WTP) for environmental protection. Findings indicate over 40% of residents neither consider the city being highly polluted nor recognize the association between air quality and adverse health outcomes, correlated with a generally low level of environmental literacy. The age, education, and health status of the participants significantly affected (p&lt;.001) their level of environmental knowledge and awareness. The SEM analysis indicates that knowledge is the major determinant in improving public awareness and perception of local air pollution (path value=0.626). Moreover, a close association between WTP and environmental attitude was also evident (path value=0.533). The findings of the present study may provide valuable insights for healthcare professionals, environmental researchers, and governmental institutions for implementing more effective public interventions to protect local air quality.

This study presents a comparative analysis of indoor air quality (IAQ) across health centers in Arakale, Iju, Owode, FECA, and Oba Ile, Ondo State, Nigeria. Particle count data were analyzed to identify common trends, similarities, and differences in IAQ parameters, with the aim of informing targeted interventions for improving indoor air quality in healthcare settings. The findings reveal consistent positive skewness in particle count distributions, indicating occasional spikes in pollution levels amidst generally lower concentrations. Fine particles in the size range of PC 2.5 were consistently dominant across all locations, emphasizing their significance in IAQ assessment. Similar variability in particle count data suggests comparable levels of fluctuations in IAQ among the health centers. However, variations in PCA patterns highlight unique factors influencing IAQ in specific locations, such as combustion sources and control strategies. Targeted interventions, including enhancing ventilation systems, controlling indoor pollution sources, and promoting smoking cessation programs, are proposed to mitigate health risks associated with indoor air pollution exposure. Ongoing monitoring and collaboration with environmental experts are crucial for assessing IAQ trends and implementing evidence-based interventions to safeguard the health of patients, staff, and visitors in healthcare facilities.

The research aims to improve some of the physical and hydro-physical properties of some Vertisols in the southern region (part of the eastern Houran Plateau) in Sweda Governorate at the south of Syria. Using different quantities of volcanic ash, soil samples were collected from the Al-Thahallah village from a depth of (0-30) cm, The experiment was designed according to the complete random design with one factor that represents the ash quantity (1.25, 2.5, 5) %, with three replicates for each treatment in addition to the control treatment a0. The experiment was carried out within the plastic pots during agricultural season 2018/2019, in which the wheat of the Sham variety 3 were cultivated as a cover plant. The results showed that the addition of volcanic ash at the quantity of 5% led to a significant increase in the infiltration rate by (328.60) %,%, where the filtration rate increased from 0.42 cm/hr -1 to 1.80 cm.h-1, as well as for each of the air porosity by (89) % and the volume of infiltrate water by (40) %, compared with the control. The above-mentioned addition also resulted in a decrease in both dry bulk density, total soil porosity and volumetric swelling coefficient by (18.60, 5.80, 314) % Respectively, compared to the control. The addition also contributed to the reduce in the weighted moisture content when saturation and the field capacity, at the level of significance of 5%. The research recommends adding volcanic ash to the soil at a quantity of 5%, and adding enhancements with volcanic ash at various levels such as organic waste.

Urban cities in sub-Saharan Africa (SSA) are faced with ambient air pollution. This is an important public health problem with models and limited monitoring data indicating high concentrations of pollutants such as fine particulate matter (PM_2.5). Going through most global air quality index maps, however, information about ambient pollution from SSA is scarce. We evaluated the feasibility and practicality of longitudinal measurements of ambient PM_2.5 using low-cost air quality sensors (Purple Air-II-SD) across thirteen locations in seven countries in SSA. Devices were used to gather data over a 30-day period with the aim of assessing the efficiency of its data recovery rate and identifying challenges experienced by users in each location. The median data recovery rate was 94% (range: 72% to 100%). The mean 24-hour concentration measured across all sites was 38 µg/m³ with the highest PM_2.5 period average concentration of 91 µg/m³ measured in Kampala, Uganda and lowest concentrations of 15 µg/m³ measured in Faraja, The Gambia. Kampala-Uganda and Nnewi-Nigeria recorded the longest periods with concentrations>250µg/m³. Power outages, SD memory card issues, internet connectivity problems and device safety concerns were important challenges experienced when using Purple Air-II-SD sensors. Despite some operational challenges, this study demonstrated that it is reasonably practicable and feasible to establish a network of low-cost devices to provide data on local PM_2.5 concentrations in SSA countries. Such data are crucially needed to raise public-, societal and policymaker awareness about air pollution across SSA.

Brewers’ spent grain (BSG) is the major by-product of beer production (70-80% moisture) and the feasibility of its application in foodstuffs depends primarily on its drying. Our objective was to evaluate the effect of physical separation with or without ultrasound application on color, total phenolic content (TPC), antioxidant activity, proximate composition, total dietary fibers, and particles size distribution of BSG powders. From wet BSG (W), two processes, without (A) or with (B) ultrasound, encompassing pressing, convective air-drying, sieving, fraction separation, and milling were evaluated. Powders A1, A2, B1 and B2 were generated. The total color difference compared with W increased throughout both processes, ranging from 1.1 (B1 x A1) to 5.7 (B1 x A2). No significant difference was observed for TPC, while lower antioxidant activity (ABTS+) was observed for process B powders, especially for B2, likely due to the release of antioxidant compounds to the liquid during pressing after ultrasound application. Nevertheless, process B powders showed higher content of total dietary fiber (p < 0.05). In conclusion, process B, with ultrasound application, may be interesting for further extraction of soluble fibers. However, the developed process A may be feasible for industrial and craft brewers, and further studies regarding the effect of their application in foods should be encouraged.

Although commercially-available low-cost air quality sensors have low accuracy, the sensor system are being used to collect the data for the regulation of PM2.5 emission caused by industrial activities or to estimate the personal exposure for PM2.5. In this work, to solve the accuracy problem of low-cost PM sensor, we developed a new PM2.5 calibration model by combining the deep neural network (DNN) optimized in calibration problem and a LSTM optimized in time-dependent characteristics. First, two datasets were generated to test the accuracy performance and generalization performance of the PM2.5 calibration machine learning (ML) model. The PM2.5 concentrations, temperature and humidity by low-cost sensor and gravimetric-based PM2.5 measuring instrument were sampled for a sufficiently long time. The proposed model was compared with benchmark (multiple linear regression model) and low-cost sensor results. For root mean square error (RMSE) for PM2.5 concentrations, the proposed model reduced 41-60% of error compared to the raw data of low-cost sensor, and reduced 30-51% of error compared to the benchmark model. R2 of ML model, MLR and raw data were 93, 80 and 59 %. Also, the developed model still showed consistent calibration performance when calibrated with new sensors in different locations. Low-cost sensors combined with ML model not only can improve the calibration performance of benchmark, but also can be applied to the sensor monitoring systems for various epidemiologic investigations and regulatory decisions.

In this contribution, unmodified silver nanoparticles were synthesized and characterized for their size and morphological properties. Thereafter, their peroxidase-like activity as the common catalytic property of silver nanoparticles was investigated by catalyzing the oxidation of 3,3’,5,5’-tetramethyl-benzidine (TMB) as peroxidase substrate, exhibiting, a specific activity as high as 5.4 µM min^-1 for the as-prepared unmodified silver nanoparticles. The stability of the catalytic activity of the as-prepared nanozymes was also checked upon their storage at ambient temperature within 7 days at different storage conditions. The results revealed that the peroxidase-like activity of unmodified silver nanoparticles was approximately retained at about 75%, and 63% after 7 days exposing daylight and air oxygen, in order. The shelf-life (storage stability) of the as-prepared nanozymes was also investigated at usual storage conditions (i.e., 4 ℃ under dark), revealed that the nanozymes saved their activity about 96% of their initial activity after 10 days of storage at 4 ℃ under dark conditions.

The 2019-2020 summer wildfire event on the east coast of Australia was a series of major wildfires occurring from November 2019 to end of January 2020 across the states of Queensland, New South Wales (NSW), Victoria and South Australia. The wildfires were unprecedent in scope and the extensive extend of the wildfires has caused smoke pollutants transported not only to New Zealand but across the Pacific Ocean to South America. At the height of the wildfires, smoke plumes were injected into the stratosphere at height up to 25km and hence transported across the globe. Based on meteorological and air quality simulation using WRF-Chem model, air quality monitoring data collected during the bushfire period and remote sensing data from MODIS and CALIPSO satellites, the extend of the wildfires and the pollutant transport, and their impacts on air quality and health on exposed population in NSW can be analysed. The results showed that WRF-Chem model using Fire Emission Inventory from NCAR (FINN) predicts the dispersion and transport of pollutants and the predicted concentration of PM2.5 and other pollutants from wildfires reasonably well when compared with ground-based and satellite data. The impact on health endpoints such as mortality, respiratory and cardiovascular diseases hospitalisation across the modelling domain is then estimated. The estimated health impact is comparable with previous study based only on observation data, but the results in this study provide much more detailed spatially and temporally with regards to the health impact from the 2019-2020 wildfire.

Dust storms originating from Central Australia and western New South Wales frequently cause high particles concentration at many sites across New South Wales, both inland and along the coast. This study focussed on a dust storm event in February 2019 which affect air quality across the state as detected at many ambient monitoring stations in the Department of Planning, Industry and Environment (DPIE) air quality monitoring network. The WRF-Chem (Weather Research and Forecast Model – Chemistry) model is used to study the formation, dispersion and transport of dust across the state of New South Wales (NSW, Australia). Wildfires also happened in northern NSW at the same time of the dust storm in February 2019, and their emissions are taken into account in WRF-Chem model by using Fire Inventory from NCAR (FINN) as emission input. The model performance is evaluated and is shown to predict fairly accurate the PM2.5 and PM10 concentration as compared to observation. The predicted PM2.5 concentration over New South Wales during 5 days from 11 to 15 February 2019 is then used to estimate the impact of the February 2019 dust storm event on three health endpoints namely mortality, respiratory and cardiac diseases hospitalisation rates. The results show that even though as the daily average of PM2.5 over some parts of the state, especially in western and north western NSW near the centre of the dust storm and wild fires, are very high (over 900 µg/m3), the population exposure is low due to the sparse population. The top five Statistical Area Level 4 regions with the most impact in term of mortality, respiratory diseases hospitalisation and cardiac disease hospitalisation are Far West and Orana, Newcastle and Lake Macquarie, New England and North West, Sydney – Inner South West and either Central Coast (mortality) or Sydney – Parramatta (respiratory diseases hospitalisation) or Sydney – Inner West (cardiac diseases hospitalisation). Generally, the health impact is similar in order of magnitude to that caused by biomass burnings events from wildfires or from hazardous reduction burnings (HRBs) near populous centres such as in Sydney in May 2016. One notable difference is the higher respiratory diseases hospitalisation for this dust event (161) compared to fire event (24).

Optimum postharvest storage conditions increase the shelf life and postharvest quality of horticultural crops. The effects of forced-air precooling (FAP) and modified atmosphere packaging (MAP) on shelf life, physicochemical quality, and health-promoting properties of bell pepper (Capsicum annuum L. cv. Nagano) harvested at 90% and 50% coloring stages in May and July respectively, stored at 11℃, 95% relative humidity were assessed. Fruits were treated with FAP + 30 μm polyethylene liner (FOLO), FAP (FOLX), 30 μm polyethylene liner (FXLO), and control (FXLX). The quality attributes, viz. weight loss, firmness, color, SSC, soluble sugars, TPC, TFC, DPPH, and ABTS were evaluated. FOLO maintained sensory quality (weight loss, firmness, and color), physicochemical (soluble solids content and soluble sugars), and health-promoting properties compared to other treatments during storage. The investigated parameters differed significantly (p &lt; 0.05) among treatments except soluble sugars. The 50% coloring fruits had a huge variation between treatments than 90% coloring. The results revealed more TPC and antioxidant capacity in 50% than in 90% coloring fruits. The study highlights the need to consider the ideal fruit coloring stage at harvest under the effect of FAP and MAP treatments in preserving bell pepper's postharvest quality and shelf life.

Urban air pollution is a critical global environmental issue, necessitating an understanding of the spatiotemporal characteristics and driving factors for effective environmental protection and urban planning. This study introduced an advanced air quality assessment system that integrates environmental, socio-economic, and urban layout factors, addressing gaps in traditional models that often overlook the impact of urban spatial structures. Analyzing air quality data from Beijing's main urban area (2016-2020) alongside multi-source geographic data, the research develops a comprehensive evaluation system, incorporating 14 key driving factors. Employing Geographically Weighted Regression (GWR) and Multi-scale Geographically Weighted Regression (MGWR), the study quantitatively assessed the influence and spatial heterogeneity of these factors. Findings revealed an annual improvement in air quality, with a U-shaped seasonal pattern and significant spatial clustering (Global Moran’s I = 0.922). The MGWR model, in particular, provided a superior fit over GWR, effectively capturing the spatial variability of factors. Variables such as NDVI), economic output (GDP), and humidity space adjustment capability (HSAC) showed significant positive spatial impacts on air quality, while population density (POP), temperature (TEMP), and road density (RD) exhibited negative effects. These insights enhance the understanding of air pollution dynamics and aid in refining urban planning strategies.

Solving environmental odor issues can be confounded by many analytical, technological, and socioeconomic factors. Considerable know-how and technologies can fail to properly identify odorants responsible for the downwind nuisance odor and mitigate it for the affected citizenry. We propose enabling solutions to environmental odor issues by utilizing troubleshooting techniques developed for the food, beverage, and consumer products industries. We showed that the downwind odorant impact-priority ranking process can be definable and relatively simple. The initial challenge is the prioritization of environmental odor character from the perspective of the impacted citizenry downwind. In this research, we aim at summarizing three natural models of the rolling unmasking effect (RUE) and discuss them more systematically in the context of the proposed downwind environmental odor prioritization approach. Regardless of the size and reach of an odor source, a simplification of odor character and composition typically develops with downwind dilution. The extreme odor simplification-upon-dilution was demonstrated for two plant varieties, prairie verbena and Virginia pepperweed. Their downwind odor frontal boundaries were dominated by single, character-defining odorants; p-cresol-dominated ‘barnyard’ odor, and benzyl mercaptan-dominated ‘burnt match’ odor, respectively. The P.T. porcupine downwind odor frontal boundary was dominated by two potent, character-defining odorants: (1) ‘onion’/‘body odor’ odorant #1 and (2) ‘onion’/‘grilled’ odorant #2. In contrast with their downwind boundary simplicities, each odor source presented considerable compositional complexity and composite character difference near the source. The proposed RUE approach’s ultimate significance is the illustration of naturally occurring phenomena that explain why some environmental odors and their sources can be challenging to identify and mitigate using the analytical only approach (focused on compound identities and concentrations). These approaches rarely move beyond comprehensive lists of compounds being emitted by the source.

The automotive industry is continuously seeking innovative solutions to improve the energy efficiency and sustainability of vehicles. Among the various energy-consuming systems in automobiles, air conditioning plays a crucial role. However, conventional vapour compression-based air conditioning systems are known for their high energy consumption and environmental impact. In recent years, adsorption technology has gained significant attention as a promising alternative due to its potential for higher energy efficiency and reduced greenhouse gas emissions. This review paper presents a comprehensive analysis of advancements in adsorption air conditioning technology specifically designed for automotive applications. The paper examines the recent research and development efforts in enhancing the performance and practicality of these systems, encompassing areas such as advanced materials selection, and system integration strategies. Furthermore, this review highlights the benefits and challenges associated with implementing adsorption air conditioning systems in vehicles. The environmental impact and potential for waste heat recovery are also discussed. Additionally, emerging trends, such as hybridization with conventional vapour compression systems, are explored to further optimize the energy efficiency and sustainability of automotive air conditioning. By critically evaluating the existing literature and research advancements, this review provides insights into the state-of-the-art thermally driven technologies for automotive applications.

We conducted a retrospective observational study to assess the hospitalization rates for acute exacerbations of asthma and/or COPD during the first imposed lockdown in Athens, Greece. Patient characteristics and the concentration of eight air pollutants (namely, CO, NO, NO2, O3 PM2.5, PM10, SO2 and benzene) were considered. A total of 153 consecutive hospital admissions were studied. Reduced admissions occurred in the lockdown period when compared to the Pre-lockdown 2020 (p&lt;0.001) or the Control 2019 (p=0.007) period. Furthermore, the concentration of 6/8 air pollutants positively correlated with weekly hospital admissions in 2020 and significantly decreased during the lockdown. Finally, admitted patients for asthma exacerbation during the lockdown were younger (p=0.046) and less frequently presented respiratory failure (p=0.038), whereas patients with COPD presented higher blood eosinophil percentage (p=0.017) and count (p=0.012). Overall, admissions for asthma and COPD exacerbations decreased during the lockdown. This might partially explained by reduction of air pollution during this period while medical care avoidance behavior, especially among elderly patients cannot be excluded. Our findings aid in understanding the untold impact of the pandemic on diseases beyond COVID-19, focusing on patients with obstructive diseases..

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Non-exhaust road transport emissions in cities contribute to poor air quality and create health impacts. This paper presents a new study of the emitted particles due to the tyres-road wear ‘TRWP’ in real driving and gives their emission factors EF. The most frequently observed particles were &lt;1 µm; followed by particles size between [1µm, 4µm] for urban, suburban and highway areas. These particle sizes are well-known to have a higher degree of toxicity. An overall analysis of all the measured pollutants gave EF equal to 30 10+12 #/km and 35 10+12 #/km, respectively for urban and sub-urban areas; and 5 10+12 #/km on highway. The analysis of the 19 most emitted pollutants, taken individually, showed that their EFs ranged from 0.003 to 18.142 10+12#/km. The obtained EF are above the value of the Euro standard for vehicles, but are below the values for vehicles unequipped with a particle filter. Significant test analysis confirmed that inertia of chemical pollutants is homogeneous. EF assessment of the PM10 and PM2.5 emitted is equal to 1.45 mg/km and 0.35 mg/km respectively. These results should contribute to the emergence of future regulations of non-exhaust emissions and should help to analyse the exposure-impact relationship to TRWP.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Background: Bioaerosol can represent a danger to the health. During SARS-CoV-2 pandemic, portable devices were used in different environments and considered a valuable prevention tool. This study has evaluated the effectiveness of the air treatment device “AEROK 1.0” in reducing microbial, particulate and pollen airborne contamination indoors, during normal activity. Methods: In an administrative room, airborne microbial contamination was measured using active (DUOSAS 360 and MD8) and passive sampling; a particle counter was used to evaluate particle concentrations; a Hirst-type pollen trap was used to assess airborne pollen and Alternaria spores. Statistical analysis was performed using SPSS 26.0; p values <0.05 were considered statistically significant. Results: The airborne bacterial contamination assessed by the two different samplers decreased by 55.54% and 69.13%, respectively. The airborne bacterial contamination assessed by passive sampling decreased by 44.16%. For fungi, the reduction was 38.7% by active sampling. Airborne particles (diameters ≥ 1.0, 2.0 μm) and the ratio of indoor/outdoor concentrations of total pollen and Alternaria spp spores significantly decreased. Conclusions: The results highlight the effectiveness of AEROK 1.0 in reducing airborne contamination. The approach carried out represents a contribution to the definition of a standardized model for evaluating the effectiveness of this type of devices.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

Research results of the relationships between air-volume in air-entrained cement paste, mortar and concrete, all designed according to PN-EN 480-1 guidelines are presented in the paper. The cement paste, mortar and concrete, with w/c=0,5 ratio, were prepared using innovative air-entraining cement CEM II/B-V. The air-entraining cement CEM II/B-V was produced using two methods: mixed together with natural or synthetic aerated admixture. The air volume test of the volumetric method was carried out in case of fresh cement paste, mortar and concrete mix. Fresh concretes were evaluated in terms of stability of air entrainment and consistency for 5, 20 and 40 min. The porosity structure parameters, like summarized air-content, specific surface of air voids, air-voids spacing factor and micropores content of hardened concrete, were estimated using computed tomography with a resolution of 2-5 μm. The aim of the research was to determine the dependence between air-content of cement paste, mortar and concrete on the measurement of air-entrainment of cement paste or mortar with the same w/c ratio and type of cement, all designed according to PN-EN 480-1 guidelines. Test results proved that there is a good correlation between the measured air-content of the cement paste, mortar and concrete. Therefore, it is possible to predict the aeration of concrete on the air-entrainment of the mortar.

Air pollution is one of the biggest problems of this age, not only it contributes to climate change but also it has a negative effect on public and individual health due to rising morbidity and mortality. There are various contaminants that play a significant role in human disease. Numerous toxins are released into the environment as a result of anthropogenic activities including burning fossil fuels for transportation and electricity generation. In order to assist decision-makers in finding a long-term solution for improving environmental quality and population health status, NO2 pollution monitoring and regulation is an essential task. Based on data acquired from Sentinel-5P, the study presented a comparison of NO2 measurements in Sentinel-5P and ground-based stations over the urban area of Fujairah during 2021 and comparison analysis of the tropospheric NO2 column spatial configuration over urban area of Fujairah during comparable periods of pre, mid and post Covid-19 pandemic era as 2019, 2020 and 2021, respectively. These findings demonstrate remarkable tropospheric NO2 column number density decreases even of 85% in the busier areas of emirate of Fujairah during the pandemic era. Sentinel-5P measurements draw attention to the significant reduction in NO2 pollution over Fujairah during the COVID-19 lockdown where we had less traffic, which is supported by ground stations-based calculations.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

The physical environment plays an important role in the transmission of respiratory infections like Covid-19. To find relevant articles on environmental factors influencing respiratory infection outbreaks, we searched Pub med Central on the following topics: 1. Environmental pollution causing coronavirus fatality- 73 results, relevant 1 article, 2. Environmental factors affecting Covid-19, 149 results from which there were 6 relevant articles, 3. Impact of air pollution on Covid-19 fatality, 10 results, relevant 3 articles, 4. Environmental factors affecting respiratory viruses- 10646 results were obtained, 2 relevant articles. We searched Google scholar on environmental factors affecting Covid-19 transmission and found 7 relevant papers. We excluded the duplicates in each of the key words search. Date of search was on 20^th April 2020. All articles included in results were scrutinized and relevance of articles was based on their content that discussed meteorological and physical environment factors in the spread and severity of Covid-19. We have discussed factors like air pollution, smoking, air temperature, humidity and air velocity as contributing factors. If meteorological factors are conducive to spread in a particular area, we need protective measures way before a respiratory infection outbreak occurs. Covid-19 is a lesson learnt the hard way, and we must enable people to practice hygienic practices with limited resources but high level of protection that it provides. Air pollution control can prevent priming of respiratory system which shall further protect from pulmonary infections.

Abstract: This article explores the intricate relationship between environmental degradation, specifically air pollution, and economic growth in the Sultanate of Oman spanning the period from 1990 to 2022. We employ cointegration and vector error correction models to uncover both short- and long-term dynamics in the association between air pollution and economic growth. Fur-thermore, Granger causality analysis is utilized to investigate the causal links between these crucial variables. This data encompasses factors related to environmental quality and various control variables. The empirical results unveil a sustained long-term cointegration connection between the variables. Additionally, our findings highlight a statistically significant positive impact of economic growth and energy consumption on CO2 emissions. Furthermore, the short-term analysis reveals an annual adjustment of approximately 14.1% in N2O emissions dis-equilibrium. The Granger causality study indicates unidirectional causal relationships involving N2O emissions, economic growth, and CO2 emissions. The implications of these findings for Oman's policy landscape are substantial. To effectively reduce greenhouse gas emissions, it is imperative for Oman to establish robust climate change policies. Additionally, the government can play a pivotal role in encouraging and endorsing the use of renewable energy sources, such as green hydrogen, as a promising alternative to traditional oil and gas resources.

As the haze engulfed the Delhi NCR after Diwali there is a panic in public about its causes and consequences. Here are some facts and figures to know the truth behind the scene. Temperature fell down from 24’C on October 31 to 21’C on November 2 as recorded at UPPCB station at sector-125, Noida which is adjacent to Delhi a very strategic location and can be considered as reference point for Delhi-NCR. The details of the study conducted is given below.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

Marine cold air outbreaks (MCAOs) are large-scale events in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing ocean near-surface wind speeds during MCAOs in atmospheric reanalysis products with different horizontal grid spacings, along with two case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. One of the main findings is that wind speeds during the strongest MCAO events are higher than normal and higher than wind speeds during less severe events. Limited evidence from the case studies suggests that reanalyses with grid spacings of more than 50 km underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. The peak times of MCAO usually occur when baroclinic waves pass over the regions. Therefore, the strong wind episodes during MCAOs generally last for just a few days. However, MCAOs can persist for 50 days or more.

The article discusses determinants of living environment in Central and Eastern Europe. As an example, the city of Radzionkow was chosen, with 16 thousand inhabitants, located in the Silesia agglomeration in southern Poland, in the area where hard coal has been mined for almost two hundred years, which largely serves as a source of heating for houses and flats. 360 buildings in 6 groups of 60 buildings were examined in the selected city, which allowed to distinguish 3 different areas in terms of the quality of the living environment depending on the technical condition of buildings, the method of heating and location. To a large extent, determinants are the existing spatial and geophysical conditions of a given location. Many research and reports on the living environment do not take into account the factors mentioned, focusing only on the statistical data of pollution, excluding spatial factors. In the research presented, the author, taking into account location variables, shows differences in the measurements of air pollution in relation to the designated location zones depending on the morphological structure of the building, the degree of its modernization and the types of heating used in buildings.

CAMx-LPiG (Comprehensive Air Quality Model with Extensions – Linear Plume in Grid) is an online hybrid model, based on the Chemistry and Transport Model (CTM) CAMx, that includes a sub-grid scale module to simulate the dispersion of linear road traffic emissions, called LPiG. LPiG is a plume in grid module specifically developed by extending the capabilities of the Lagrangian puff sub-grid model available in CAMx. The online integration of the local scale model within the Eulerian CTM allows for a multiscale simulation of air quality from the regional scale to the urban scale, preserving a coherent description of the chemical state of the atmosphere at all spatial scales and avoiding any double counting of the emissions simulated by the sub-grid module. In this work the model is presented and evaluated against measured NO2 concentrations for the city of Milan for the month of January 2017. The model is able to introduce road traffic induced gradient in NO2 concentration at sub-grid resolution. Moreover, CAMx-LPiG is shown to reduce the bias compared to CAMx stand-alone simulations.

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Livestock production systems generate nuisance odor and gaseous emissions affecting local communities and regional air quality. Also, there are concerns about the occupational health and safety of farm workers. Proven mitigation technologies that are consistent with the socio-economic challenges of animal farming are needed. We have been scaling up the photocatalytic treatment of emissions from lab-scale, aiming at farm-scale readiness. In this paper, we present the design, testing, and commissioning of a mobile laboratory for on-farm research and demonstration of performance in real farm conditions. The mobile lab is capable of treating up to 1.2 m3·s-1 of air with TiO2-based photocatalysis and adjustable UV-A dose based on LED lamps. We summarize the main technical requirements, constraints, approach, and performance metrics for the mobile laboratory, such as the effectiveness (measured as the percent reduction) and cost of photocatalytic treatment of air. The commissioning of all systems with standard gases resulted in ~9% and 34% reduction of NH3 and butan-1-ol, respectively. We demonstrated that as the percent reduction of standard gases increased with increased light intensity and treatment time. These results show that the mobile laboratory was ready for on-farm deployment and evaluating the effectiveness of UV treatment.

Human factors are the things that go wrong in the interactions between a team of people and a system of technology. This is part of a broader transdisciplinary field called engineering psychology, which as the name suggests, draws from both engineering and psychology. Many, if not most, catastrophic accidents involve a socio-technical interaction, i.e. are not solely due to technology failure. Hence, there is a need to consider human factors in the development or deployment of any technical system. This article is about the human factors involved in an aviation accident in New Zealand between a Yak and a cherry picker. The types of human error are identified, and the barrier bowtie method is used to represent them. The analysis gives different insights into the accident compared to the formal accident report, and better represents the human error characteristics.

It is essential to mitigate gaseous emissions that result from poultry and livestock production to increase industry sustainability. Odorous volatile organic compounds (VOCs), ammonia (NH3), hydrogen sulfide (H2S), and greenhouse gases (GHGs) have detrimental effects on the quality of life in rural communities, the environment, and climate. This study's objective was to evaluate the photocatalytic UV treatment of gaseous emissions of odor, odorous VOCs, NH3, and other gases (GHGs, O3 – sometimes considered as by-products of UV treatment) from stored swine manure on a pilot-scale. The manure emissions were treated in fast-moving air using a mobile lab equipped with UV-A and UV-C lights and TiO2-based photocatalyst. Treated gas airflow (0.25 to 0.76 m3/s) simulates output from a small ventilation fan in a barn. Through controlling the light intensity and airflow, UV dose was tested for techno-economic analyses. The treatment effectiveness depended on the UV dose and wavelength. Under UV-A (367 nm) photocatalysis, the percent reduction of targeted gases was up to i) 63% of odor, ii) 51%, 51%, 53%, 67%, and 32% of acetic acid, propanoic acid, butanoic acid, p-cresol, and indole, respectively, iii) 14% of nitrous oxide (N2O), iv) 100% of O3, and 26% generation of CO2. Under UV-C (185+254 nm) photocatalysis, the percent reductions of target gases were up to i) 54% and 47% for p-cresol and indole, respectively, ii) 25% of N2O, iii) 71% of CH4, and 46% & 139% generation of CO2 & O3, respectively. The results proved that the UV technology was sufficiently effective in treating odorous gases, and the mobile lab was ready for farm-scale trials. The UV technology can be considered for the scaled-up treatment of emissions and air quality improvement inside livestock barns.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.