Today, the style of light construction materials used in building is one of the most important factors in reducing building's dead load and better performance of the structures in the earthquake. One of the ways to reduce the structure weight is to use lightweight blocks instead of using traditional materials. The main purpose of this research is to compare density, compressive strength and water absorption volume of non-load-bearing lightweight blocks made of natural and artificial lightweight aggregates. Scoria lightweight aggregates of Sanandaj, Ghorveh mine, pumice in Tabriz, Bostanabad mine, and Leca in Leca enterprise have been used to make the samples. Given the importance of the materials used, grading of coarse-grained materials has been conducted based on the standard of 7657 and grading of fine materials have been conducted based on the standard of 302.The experiments' results show that Scoria blocks due to hard texture, and high mechanical resistance of their lightweight aggregates, have had higher compressive strength, and density and lower water absorption volume compared to pumice and Lika lightweight aggregate blocks. Pumice blocks despite having desirable compressive strength and lower density compared to the two other blocks have higher water absorption volume, and do not meet the standard conditions. This same factor causes it faces with less interest. Among these Lika blocks with density of 1151.94 (kg per cubic meter) below 2000 kilograms per cubic meter of Iran density standard of 7782 (28-day compressive strength of 2.57 MPa), higher than 2.5 MPa of Iran compressive strength standard of 7782 (and water absorption volume of 282.92 kg per cubic meter) below 288 kilograms per cubic meter of Iran water absorption volume standard of 7782 (as a non-load-bearing lightweight block) have been diagnosed desirable.

The difficult current environmental situation, caused by construction industry residues containing ceramic materials could be improved by using these materials as recycled aggregates in mortars, with their processing causing a reduction in their use in landfill, contributing to recycling and also minimizing the consumption of virgin materials. Although some research is currently being carried out into recycled mortars, little is known about their stress-strain (σ-ε); therefore this work will provide the experimental results obtained from recycled mortars with recycled ceramic aggregates (with contents of 0, 10, 20, 30, 50 and 100%), such as: the density, the compression strength, as well as the σ-ε curves representative of their behavior. The values obtained from the analysis process of the results are those of: σ (elastic ranges and failure maximum), ε (elastic ranges and failure maximum), and Resilience and Toughness; in order to finally obtain, through numerical analysis, the equations to predict their behavior (related to their recycled content). At the end of the investigation it is established that mortars with recycled ceramic aggregate contents of up to 20% could be assimilated just like mortars with the usual aggregates, and the prediction equations produced could be used in cases of similar applications.

In order to fully perform their functions and be durable, mortars for renders and plasters are requested to have a set of characteristics that can vary with the type of exposure to external environmental actions and the type of substrate. Generally, they need moderate strength, high deformability, some water protection capability, good adhesion to the substrate, and compatibility with the pre-existent materials. The presence of water and its movement inside the pore structure of the mortars are among the most significant causes of degradation. Moreover, several authors consider that the main factors for durability and good performance of lime-based mortars are mostly related with the good quality of the binder and the use of adequate aggregates. This paper intends to study the effect of ageing on the properties and durability of air lime mortars, using aggregates of different mineralogy. For this purpose, different mortars compositions are exposed to an accelerated weathering test under defined conditions. The obtained characteristics are discussed and compared with the results obtained with the same mortars tested in laboratory conditions. The effects of the aggregate type on the durability of mortars seem to be linked to their effects on the mortars porous structure.

In this study, four samples of recycled aggregates from construction and demolition waste of Mexico City were characterized, in order to find innovative uses for this type of materials. Gravel and sand from a recycling plant were analyzed, as well as recycled aggregates in the laboratory from demolished concrete collected in landfills. The characterization was carried out by means of XRD, chemical microanalysis (EDS), pH measurement and sieve analysis. The results reveal that the minerals present in the analyzed materials are triclinic feldspars, cristobalite and pyroxene which correspond to the natural aggregates, as well as variable amounts of calcite, product of the carbonation of the cement paste adhered to these aggregates and in a smaller proportion calcium hemicarboaluminate, rosenhanite and tobermorite. It was determined that the quality (amount of cement) of the original concrete that was recycled, has great influence on the granulometry and the chemical-mineralogical composition of the aggregates, since there will be different quantities and qualities of cement paste adhered to the aggregates of according to size. Finally the pH values measured in all samples fluctuate between 10.15 and 12.08, therefore it is suggested that these materials can be used in soil stabilization.

The annual construction and demolition waste (CDW) generated from EU construction sector was 850 million tons, which represented 31% of the total waste generation and about 28% of CDW was ceramics (bricks and tiles). In this study, the feasibility of using CDW brick powder as the precursor of alkali activated mortar (AAM) and extruded polystyrene (XPS) as the lightweight aggregates to form lightweight brick powder AAM (LW-BP-AAM) for non-structural applications was investigated. The thermal conductivity of LP-BPAAM was 0.112 W/m·K with density of about 1,135 kg/m³ which was lower than the counterparts with similar density in literature. The acid resistance of LW-BP-AAM is comparable to conventional fly ash based AAM and superior than ordinary Portland cement. From the scanning electron microscopy with energy dispersive X-ray spectroscopy, there was no severe damage on the surface of LW-BP-AAM but aluminate was removed from the matrix which was further verified in Fourier transform infrared spectroscopy. The mass and strength loss of LP-BP-AAM was 1.5% and 33%, respectively. Although the compressive strength of the LP-BP-AAM was low (about 1.8 MPa), it can be improved by optimising the particle size of the XPS aggregates.

This paper investigates the effect of alteration on the physicomechanical properties of igneous rocks from various areas from Greece used as aggregates. The studied lithologies include dunites, harzburgites, lherzolites, gabbros, diabases, dacites and andesites. Quantitative petrographic analysis shows that the tested samples display various percentages of secondary phyllosilicate minerals. Mineral quantification of studied rock samples was performed by using a Rietveld method on X-Ray diffraction patterns of the studied aggregates. The aggregates are also tested to assign moisture content [w (%)], total porosity [nt (%)], uniaxial compressive strength [UCS (MPa)] and Los Angeles abrasion test [LA (%)]. The influence of secondary phyllosilicate minerals on physicomechanical behavior of tested samples determined using regression analysis and their derived equations. Regression analysis shows positive relationship between the percentage of phyllosilicate minerals of rocks and moisture content as well as with the total porosity values. The relationships between phyllosilicate minerals in the ultramafic and mafic samples and their mechanical properties show that the total rates of phyllosilicate mineral products result negatively in their mechanical properties, while the low percentage of phyllosilicate minerals in volcanic rocks are not able to define set of their engineering parameters.

Precipitation processes are technologies commonly used in hydrometallurgical plants to recover metals or to treat wastewaters. Moreover, solid-liquid separation technologies, such as thickening or filtering, are relevant unit operations, included in the precipitation technologies. These methods are strongly dependent on the characteristics of the solid precipitates formed during the specific precipitation reaction. One of these characteristics is the particle size distribution (PSD) of the solid precipitates which are fed into a solid-liquid separation process. Therefore, PSD determination is a typical practice for the characterization of the slurries generated in a precipitation plant. Furthermore, the precipitates generated in these processes have a colloidal or aggregation behavior, depending on the operational conditions. Nevertheless, the conventional methods used to estimate PSD (e.g., laser diffraction and/or ciclosizer) have not been designed to measure particles that tend to aggregate or disaggregate, since they include external forces (e.g., centrifugal, agitation, pumping and sonication). These forces affect the true size of the aggregates formed in a unit operation, thereby losing representativity in terms of aggregates particle size. This study presents an alternative method of measuring the size distribution of particles with aggregation behavior, particularly, by using non-invasive microscopy and image processing and analysis. The samples used have been obtained from an experimental precipitation process by applying sulfidization to treat the cyanide-copper complexes contained in a cyanidation solution. This method has been validated with statistical tools and compared with a conventional analysis based on laser diffraction. Our results show significant differences between the methods analyzed, demonstrating that image processing and analysis by microscopy is an excellent and non-invasive alternative to obtaining size distribution of aggregates in precipitation processes.

With increasing interest in the use of additive manufacturing techniques in the construction industry, static rheological properties of fresh concrete have necessarily come into focus. In particular, the knowledge and control of static yield stress (SYS) and its development over time are crucial for mastering formwork-free construction, e.g. by means of layered extrusion. Furthermore, solid understanding of the influences of various concrete constituents on the initial SYS of the mixture and the structural build-up rate is required for purposeful material design. This contribution is concentrated on the effect of aggregates on these rheological parameters. The volume fraction of aggregates was varied in the range of 35 to 55 % by volume under condition of constant total surface area of the particles. The total surface area per unit volume of cement paste was equal to 5.00, 7.25 and 10.00 m²/l, conditioned on the constant volume fraction of aggregates. Both variations were enabled by changing the particle size distributions of the aggregates while holding the cement paste composition constant for all concrete mixtures. To characterise the SYS and the structural build-up, constant shear rate tests with a vane-geometry rotational rheometer were performed. It was found that in the ranges under investigation the variation in volume fraction had a more pronounced effect on the static rheological properties of concrete than did the variation in surface area. An accurate mathematical description of the relationship between the initial SYS of concrete and the relative volume fraction of aggregate based on the Chateau-Ovarlez-Trung model was proposed. Challenges in deriving a similar relationship for the structural build-up rate of concrete were highlighted.

Understanding platelet functionality has undergone a sea change in the last decade. No longer are platelets viewed simply as regulators of haemostasis; they are now acknowledged to be pivotal in coordinating the inflammatory and immune responses. This expanded role for platelets brings new opportunities for controlling a range of health conditions, targeting platelet activation and their interactions with other vascular cells. Antiplatelet drugs may be of wider utility than ever expected but often cause too strong a platelet suppression to be used out of clinical settings. Dietary antiplatelets represent a nutritional approach that can be efficacious while safe for general use. Here we review potential new uses for dietary antiplatelets outside the field of cardiovascular health, with specific reference to the water-soluble tomato extract Fruitflow®. Uses in different aspects of inflammation and immune function are discussed, highlighting exercise-induced inflammation, mediating the effects of air pollution, and controlling thrombotic aspects of the immune response. Potential future developments in women’s health, erectile dysfunction, and the allergic response give an indication of how wide-ranging the utility of dietary antiplatelets can possibly be.

This paper investigates an alternative use of sterile aggregate materials which may arise from various construction applications in conjunction with other low-cost mineral raw materials to remediate the acid mine drainage phenomenon. This study is based on the combination of unprocessed mineral raw materials as well as on the basic concept of the cyclic economy where the conversion of a waste into a raw material for another application can be achieved. In this way, the value of mineral raw materials can be prolonged for as long as possible, waste generation and exploitation of natural resources are minimized and resources are kept as far as possible within the existing economy. In this study, an electrically continuous flow driven forced device proposed and demonstrated for the remediation of waste water in lab-scale by using certain mixes of mineral raw materials (serpentinite, andesite, magnesite, peat and biochar). Our results focus on the impact of the studied mineral raw materials and especially on their synergy on the water purification potential under continuous water flow operation. Using the proposed 7-day experimental electrically continuous flow driven forced device with the certain mixes of mineral raw materials, the increase of pH values from 3.00 to 6.82 as well as significant removal of Fe, Cu and Zn was achieved.

The global environmental impact of plastic waste is significant, with only 9% being recycled, causing pollution and harming the environment and humans. Due to increased traffic, limited funding, and dwindling natural resources, Jordan's road network is deteriorating rapidly. Pavement performance can be improved through high-quality materials and sustainable construction practices. The research investigates using Polyethylene Terephthalate as a polymer additive in asphalt mixtures to enhance their properties. Basalt and limestone mixtures were applied to asphalt mixtures. The optimal binder content for the control mixture was 4.8% for basalt and 4.93% for limestone. When modified with 10% PET, the basalt mixture showed slightly better stability than the control mix, while higher PET proportions led to reduced strength. PET-modified mixtures consistently displayed higher flows and bulk densities, with a more pronounced impact on the basalt mixture. PET increased the air-void ratio in basalt but had minimal effect on VMA. PET offers economic and environmental advantages, saving 8.4% of the original bitumen cost. As a result, limestone mixture properties, which are inferior to basalt mixture properties, improved significantly compared to basalt mixture properties. PET has the potential to create sustainable and high-performing asphalt mixtures, providing valuable insights for road construction and environmental management.

One of the major problems caused by repeated subcutaneous insulin injections in diabetic patients is insulin amyloidosis. Understanding the molecular mechanism of amyloid fibril formation of insulin and finding effective compounds to its inhibit or eliminate is very important and extensive research has been done on it. In this study, the anti-amyloidogenic and destabilizing effects of the pyrogallol, as a phenolic compound, on human insulin protein were investigated by CR absorbance, ThT and ANS fluorescence, FTIR spectroscopy and atomic force microscopy. According to the obtained results, the formation of amyloid fibrils at pH 2.0 and 50 °C was confirmed by CR, ThT, ANS, FTIR assays. Microscopic images also showed the twisted and long structures of amyloid fibrils. Simultaneous incubation of the protein with pyrogallol at different concentrations reduced the intensities of CR, ThT and ANS in a dose-dependent manner and no trace of fibrillar structures was observed in the microscopic images. FTIR spectroscopy also showed that the position of amide I band in the spectrum of samples containing pyrogallol was shifted. Based on the findings in this study, it can be concluded that pyrogallol can be effective in preventing and suppressing human insulin amyloid fibrils.

Neurodegenerative protein conformational diseases are characterized by misfolding and aggregation of metastable proteins encoded within the host genome. The host is also home to thousands of proteins encoded within exogenous genomes harbored by bacteria, fungi, and viruses. Yet, their contributions to host protein-folding homeostasis, or proteostasis, remain elusive. Recent studies, including our previous work, suggest that bacterial products contribute to toxic aggregation of endogenous host proteins. We refer to these products as bacteria-derived protein aggregates (BDPAs). Furthermore, antibiotics were recently associated with increased risk for neurodegenerative diseases, including Parkinson’s disease and amyotrophic lateral sclerosis  possibly by virtue of altering the composition of the human gut microbiota. Other studies have shown a negative correlation between disease progression and antibiotic administration, supporting their protective effect against neurodegenerative diseases. These contradicting studies emphasize the complexity of the human gut microbiota, the gut-brain axis, and the effect of antibiotics. Here, we further our understanding of bacteria’s effect on host protein folding using the model Caenorhabditis elegans. We employed genetic and chemical methods to demonstrate that the proteotoxic effect of bacteria on host protein folding correlates with the presence of BDPAs. Furthermore, the abundance and proteotoxicity of BDPAs are influenced by gentamicin, an aminoglycoside antibiotic that induces protein misfolding, and by butyrate, a short-chain fatty acid that we previously found to affect host protein aggregation and the associated toxicity. Collectively, these results increase our understanding of host-bacteria interactions in the context of protein conformational diseases.

Flaviviruses replicate in membrane factories associated with the endoplasmic reticulum (ER). Significant levels of flavivirus viral protein accumulation contribute to ER stress. As a consequence, the host cell exhibits an Unfolded Protein Response (UPR), subsequently stimulating appropriate cellular responses such as adaptation, autophagy or apoptosis. The correct redox conditions of this compartment are essential to form native disulfide bonds in proteins. ZIKA virus (ZIKV) has ability to induce persistent ER stress leading to activation of UPR pathways. In this study, we wondered whether ZIKV affects the redox balance and consequently the oxidative protein folding in the ER. We found that ZIKV replication influences redox state leading to aggregation of viral envelope protein as amyloid-like structures in the infected cells.

Purpose - Soil aggregates are of great significance to soil and water conservation and ecological environment construction in arid area of northwest district．Methods - Exploring the effects of different vegetation includes types and land use methods on the stability of soil aggregates in the Loess Plateau, and provide reference for the rational use and management of land, also the improvement of soil structure in the region. Select 9 types of samples of 0-30 cm of typical soil plots as the research objects, compare and analyze the particle size index, stability differences and anti-erodibility of soil aggregates under various vegetation cover. Results - The results show that P value, MWD value, GMD value, D value, and AI value of the 0-10cm surface soil all show the maximum value. As the depth increases, the size distribution of the above index values of each soil sample in the 10-20cm and 20-30cm layers is different; P value in the 0-30cm depth layer is linearly positively correlated with the AI value and MWD value, and linearly negatively correlated with the D value. The correlation coefficient R between each variable is in the range of 0.78-0.97, and the D value reflects the Loess Plateau area stability and erosion resistance of soil aggregates better. GMD and MWD value show an exponential relationship, the correlation coefficient R value of 10-20cm height layer is 0.46; AI and MWD value in 0-10cm, 20-30cm height layer have a power function relationship, 10-20cm height layer has a polynomial function, the correlation coefficient R value is 0.97. The scour coefficient of different soil samples has a high degree of dispersion, the maximum CV value is 1.92, and the minimum value is 0.49. Conclusions - The results of this study can provide a theoretical basis for the ecological and hydrological benefit evaluation of slope erosion control and vegetation restoration on the Loess Plateau.

Shear deformation of a solid-fluid, two-phase material induces a fluid segregation process that produces fluid-enriched bands and fluid-depleted regions, and crystallographic preferred orientation (CPO) characterized by girdles of [100] and [001] axes sub-parallel to the shear plane and a cluster of [010] axes sub-normal to the shear plane, namely the AG-type fabric. Based on experiments of two-phase aggregates of olivine + basalt, a two-phase flow theory and a CPO-formation model were established to explain these microstructures. Here, we investigate the microstructure in a two-phase aggregate with supercritical CO2 as the fluid phase and examine the theory and model, as CO2 is different from basaltic melt in rheological properties. We conducted high‐temperature and high-pressure shear deformed experiments at 1 GPa and 1100ºC in a Griggs-type apparatus on samples made of olivine + dolomite, which decomposed into carbonate melt and CO2 at experimental conditions. After deformation, CO2 segregation and an AG-type fabric occurred in these CO2-bearing samples, inconsistency with basaltic melt-bearing samples. The SPO-induce CPO model was used to explain the formation of the fabric. Our results suggest that the influences of CO2 as a fluid phase on the microstructure of a two-phase olivine aggregate is similar to that of basaltic melt and can be explained by the CPO-formation model for the solid-fluid system.

Soil aggregates, as the basic component of soil, make great contributions to the stability of soil structure and soil carbon (C) sequestration. Recently, grassland is experiencing continuous grazing, which greatly affects soil aggregation and soil C storage. However, how soil aggregates and soil C in different grassland respond to grazing remain unclear. In this study, three national fenced grassland monitoring field stations which represented mountain meadow (MM), temperate steppe (TS), temperate steppe desert (TSD) were selected, soil samples at 0–10 cm depth of inside and outside the fence were collected to explore the effect of grazing and grassland type on composition, stability and nutrients of soil aggregates. The results showed that the bulk soil organic carbon (SOC), total nitrogen (TN), total phosphorus (TP), available nitrogen (AN) and available phosphorus (AP) varied greatly among the three grassland types, with the highest values in MM. Soil aggregates composition showed significantly response to both grassland type and grazing, especially the proportion of soil aggregates >2 mm, which significantly decreased 51.68% on average in grazing plots compared with fenced plots, whereas sharply decreased in MM and TSD. A significant decrease (on average 25.08%) of the mean weight diameter (MWD) of soil aggregates under grazing was detected across all grassland types. The effect of grazing on nutrients in macroaggregates (>0.25 mm) was greater than that in microaggregates (<0.25 mm). Aggregate-associated SOC concentration decreased under grazing in MM and TSD, however, SOC density showed different response to grazing across all grassland types, with minor effect on MM, decreasing SOC density in TS and increasing on TSD, respectively. The magnitude of grazing effect size on aggregate-associated SOC varied in different soil particle size, with greater response in aggregates > 2 mm and the biggest value in TDS. In addition, correlation analysis showed that MWD of soil aggregates had significant negative correlation with soil bulk density, but significant positive correlation with SOC, TN and TP concentration. Results of RDA showed that BD, soil nutrients were the main influence factors of the composition and stability of aggregates. Overall, grazing had significant influence on soil aggregation, stability and SOC, played a crucial role in grassland soil stability and the accumulation of SOC.

Synthesis of ZSM-5 zeolite from OSDA-free systems has been a very interesting alternative method because it can avoid the usage of organic templates and consequent calcination step. However, in opened reports, organic substance such as alcohol is more or less involved. In the present work, a calcined commercial ZSM-5 zeolite was used as a seed, sodium aluminate as an aluminum source, silica sol as a silicon source, which ensures that there is no any organics (template) in the synthesis system, and polycrystalline ZSM-5 aggregates consisting of rod-like nanocrystals are successfully prepared in a completely OSDA-free system. The effects of seed (chemical component, dosage) and crystallization conditions on the synthesis of ZSM-5 were systematically investigated. The results show that highly crystallinity ZSM-5 aggregate consisting of primary nano-sized crystals with a size of less than 100 nm can be yielded from a gel precursor with 5.6 wt.% seed after hydrothermal treatment for 48 h. The results also shows that the chemical composition of the seeds had little effect on the topological structure and pore structure of the synthesized samples, but the seed with a low Si/Al ratio is more conducive to the rapid crystallization of zeolite and to the improvement of the acid, especially the strong acid centers of the catalyst.

We have established earlier a cell line from the human limbal area to study cell growth and response to the toxic effects of antibiotics used in ophthalmology. In the recent work, the effect of multi-walled carbon nanotubes (MWCNTs) in cornea damage was investigated in vitro and in vivo in mice. In the in vitro experiments, the physiological effects of multi-walled carbon nano-tube (MWCNT) bundles on corneal wound healing were mimicked in vitro by a reepithelization limbal stem cell model. Murine in vivo experiments were performed with intact, non-functionalized MWCNTs to confirm the validity of in vitro tests. The MWCNTs of 10 -30 nm outer diameter at low concentration (5 µg/ml) did not interfere with the wound healing of the damaged limbal cell monolayer. Higher than 50 µg/ml concentrations: a) generated MWCNT aggregates, b) restrained the movement and prolonged the time of wound healing, c) increased the amplitudes of the oscillations of the cells, and d) resulted in scar formation affecting both cor-neal function and refraction. Chromatin condensation, a sensitive test of the viability of cells, including limbal stem cells revealed that the presence of a low concentration of nanotubes (5 µg/ml), did not significantly affect the viability of limbal cells. Chromatin condensation was completed and metaphase chromosomes were seen at higher MWCNT concentration proving that their aggregates did not affect the viability of limbal cells. This concentration of MWCNTs (5 µg/ml) did impact neither the reepithelization in vitro nor in vivo in the scratched eyes of mice. Scar formation took place at higher than 50 µg/ml concentrations and the healing of the cornea was prevented by the lack of movement of increasingly larger macroaggregates. In vivo murine experiments vali-dated in vitro monolayer regrowth followed by time-lapse microscopy portraying realistically the reepithelization of the damaged cornea that process was gradually slowed down by macro aggregate formation and caused the scarring of the cornea.

Alkali-silica reactivity (ASR) is one of multiple reactions responsible for premature loss in concrete infrastructure service life. ASR is a deleterious reaction initiated when highly reactive silicious content of aggregates reacts with alkali hydroxides content within portland cement in the presence of moisture. ASR results in the formation of expansive, white-colored gel-like material which results in internal stresses within hardened concrete. ASR induced stresses result in concrete cracking, spalling, and increased reinforcement steel corrosion rates. The main objective of this research is to improve the conditions of concrete infrastructure projects conditions by mitigating ASR damaging effect. The expansion of accelerated mortar bars poured using fine aggregates collected from different sources is measured versus time to evaluate aggregate’s reactivity. Different percentages of supplementary cementitious materials (SCMs) including class c fly ash, micro-silica, were used in remixing mortar bars to evaluate the efficiency of different types of SCMs in mitigating mortar bar expansion. Research findings showed that SCMs can mitigate ASR, thus, decrease the mortar bar expansion. The efficiency of SCMs in ASR mitigation is highly dependent on the incorporated SCM percentage and particle fineness. Silica fume, having the least particle size, displayed higher rates of ASR mitigation followed by fly ash, respectively. The outcomes of this research will assist design engineers in avoiding future losses due to ASR cracking in concrete infrastructure projects, and reduce the excessive need to maintenance, repair, and replacement activities.

The term neuroinflammation defines the reactions of astrocytes and microglia to alterations in homeostasis in the diseased central nervous system (CNS), the exacerbation of which contributes to the neurodegenerative effects of Alzheimer's disease (AD). Local environmental conditions, such as the presence of proinflammatory molecules, mechanical properties of the extracellular matrix (ECM) and local cell-cell interactions, are determinants of glial cell phenotypes. In AD, the load of the cytotoxic/proinflammatory amyloid β peptide (Aβ) is a microenvironmental component increasingly growing in the CNS, imposing time-evolving challenges on resident cells. This study aimed at investigating the temporal and spatial variations of the effects produced by this process on astrocytes and microglia, either directly or by interfering in their interactions. Ex vivo confocal analyses of hippocampal sections from the mouse model TgCRND8 at different ages have shown that overproduction of Aβ peptide induced early and time persistent disassembly of functional astroglia syncytium and promoted a senile phenotype of reactive microglia, hindering Aβ clearance. In the late stages of disease, these patterns were altered in the presence of Aβ-plaques, surrounded by typically reactive astrocytes and microglia. Morphofunctional characterization of peri-plaque gliosis revealed a direct contribution of astrocytes in plaque buildup that might result in shielding Aβ-peptide cytotoxicity and, as a side effect, in exacerbating neuroinflammation.

Severe COVID-19 is frequently associated with thromboembolic complications. Increased platelet activation and platelet-leukocyte aggregate formation can amplify thrombotic responses by inducing tissue factor (TF) expression on leukocytes. Here, we characterized TF-positive extracellular vesicles (EVs) and their cellular origin in 12 patients suffering from severe COVID-19 (time course, 134 samples overall) and 25 healthy controls. EVs exposing phosphatidylserine (PS) were characterized by flow cytometry. Their cellular origin was determined by staining with anti-CD41, anti-CD45, anti-CD235a, and anti-CD105 as platelet, leukocyte, red blood cell, and endothelial markers. We further investigated the association of EVs with TF, platelet factor 4 (PF4), C-reactive protein (CRP) and high mobility group box-1 protein (HMGB-1). COVID-19 patients showed higher levels of PS-exposing EVs compared to controls. The majority of these EVs originated from platelets. A higher amount of EVs in patient samples were associated with CRP, HMGB-1, PF4, and TF, as compared to EVs from healthy donors. In COVID-19 samples, 16.5% of all CD41+ EVs displayed the leukocyte marker CD45, and 55.5% of all EV aggregates (CD41+CD45+) co-expressed TF, which reflects the interaction of platelets and leukocytes in COVID-19 on an EV level.

The recent setbacks in the withdrawal and approval delays of antibody treatments of neurodegenerative disorders (NDs) can be attributed to their poor entry across the blood-brain barrier (BBB). While several invasive and noninvasive approaches can be used to make the BBB more permeable, their inconsistency makes them a poor choice; however, if an antibody is chemically modified to attach a transferrin molecule that enhances its permeation across the BBB, this could be the most practical and useful modification that can transform the science of ND treatment. Antibodies can be conjugated with transferrin in vitro, but preferably through mRNA, as we propose to convert current treatments to bring faster treatment options. The mRNA technology yields products at a meager cost, which is a consideration for the affordability of these drugs globally. This paper provides complete details with templates to convert the current medicines and those under development into mRNA delivery systems to ensure clinical success, avoiding the current failures in their efficacy, more specifically the products that have demonstrated efficacy but are being removed from the market.

This paper presents the light scattering matrices of atmospheric aggregated hexagonal ice particles appearing in cirrus clouds. In this work aggregates consist of the same particles with different spatial orientation and number of these particles. Two types of particle shape were studied: (1) hexagonal column; (2) hexagonal plate. For both shapes we study compact and non-compact cases of arrangement of particles in aggregates. As a result, four sets of aggregates were made: (1) compact columns; (2) non-compact columns; (3) compact plates; (4) non-compact plates. Each set consists of eight aggregates with different number of particles from 2 to 9. For practical reason the bullet-rosette and the aggregate of hexagonal columns with different sizes was also calculated. The light scattering matrices were calculated for the case of arbitrary spatial orientation within the geometrical optics approximation for sets of compact and non-compact aggregates and within the physical optics approximation for two additional aggregates. It was found that light scattering matrix elements for aggregates are depend on arrangement of particles they are consisted.

Anode materials based on TiO2 nanoparticles of different morphologies were prepared using the hydrothermal method and characterized by various techniques, such as X-ray diffraction (DRX), scanning electron microscopy (FE-SEM), and N2 absorption. The TiO2 nanoparticles prepared were used as anode materials for lithium-ion batteries (LIBs), and their electrochemical properties were tested using discharging/charging measurements. The results showed that the initial morphology of the nanoparticles plays a minor role in battery performance after the first few cycles and that better capacity was achieved for TiO2 nanobelt morphology. The sharp drop in the specific capacity of LIB during their first cycles is examined considering changes in the morphology of TiO2 particles and their porosity properties in terms of shape and connectivity.

The α-synucleinopathies are a group of neurodegenerative diseases characterized by the deposition of α-synuclein aggregates (α-syn) in the brain. Currently, there is no suitable tracer to enable a definitive early diagnosis of these diseases. We reported candidates based on 4,4'-disarylbisthiazole (DABTA) scaffold with a high affinity towards α-syn and excellent selectivity over Aβ and tau fibrils. Based on prior in silico studies a focused library of 23 halide-containing and O-methylated DABTAs was prepared. The DABTAs were synthesized via a modified two-step Hantzsch thiazole synthesis, characterized, and used in competitive binding assays against [3H]PiB, and [3H]DCVJ. The DABTAs gave an overall chemical yield of 15 – 71%, with a calculated lipophilicity of 2.5 – 5.7. The ligands demonstrated an excellent affinity to α-syn with both [3H]PiB and [3H]DCVJ: Ki 0.1 – 4.9 nM and up to 20 – 3900-fold selectivity over Aβ and tau fibrils. It could be concluded that in-silico simulation is useful for the rational design of a new generation of DABTAs. Further investigation of the leads in the next step is encouraged: radiolabeling of the ligands with radioisotopes such as fluorine-18 or carbon-11 for in vivo, ex vivo and translational research and for further in vitro experiments on human-derived protein aggregates.

Hexakis(2-alkoxy-1,5-phenyleneimine) macrocycles were synthesized using a simple one−pot procedure through by precipitation−driven cyclization. The acetal−protected AB−type monomers, 2-alkoxy-5-aminobenzaldehyde diethyl acetals, underwent polycondensation in water or acid−containing tetrahydrofuran. The precipitation−driven cyclization based on imine dynamic covalent chemistry and π−stacked columnar aggregation played a decisive role in the one−pot synthesis. The progress of the reaction was analyzed by MALDI−TOF mass spectrometry. The macrocycles with alkoxy chains were soluble in specific organic solvents such as chloroform, allowing their structures to be analyzed by NMR. The shape−anisotropic, nearly planar, and persistent macrocycles aggregated into columnar assemblies in polymerization solvents, driven by aromatic π−stacking. The octyloxylated macrocycle OcO−Cm6 exhibited an enantiotropic columnar liquid crystal−like mesophase between 165°C and 197°C. In the SEM image of (S)-(−)-3,7-dimethyloctyloxylated macrocycle (−)BCO-Cm6, columnar substances with a diameter of 100−200 nm were observed. The polymerization solution for 2-(2-methoxyethoxy)ethoxy)ethoxylated macrocycle (TEGO−Cm6) gelled and showed thixotropic properties by forming a hydrogen bond network.

The soil organic matter (SOM) content and stability in natural gypsum soils and soils from mining/industrial areas were compared, in terms of their physical, chemical and micromorphological properties, to determine whether the old brownfield soils were acting as carbon (C) sinks, counteracting increasing carbon dioxide concentrations in the atmosphere. The mining/industrial soils were 50–400 years old, so had been left sufficiently long for full self-restoration. Despite having very different origins, both natural and brownfield soils stored similar amounts of SOM, and had similar pH values, calcium carbonate contents and textures. They were also fully covered with similar grass plant communities. The mining/industrial soils exhibited similar microstructures to the gypsum soils and were often quite porous. The most striking difference between them and the natural gypsum soils was that the mining/industrial soils were strongly polluted with zinc, lead and cadmium. The 50-year-old brownfield soils differed from the others in terms of having a lower state of SOM transformation, with a much higher C/N ratio, lower aggregate water resistance index, lower dehydrogenase activity and greater areas of undecomposed or slightly decomposed plant residues. These parameters in the older (150–400 years) brownfield soils were similar to those of the natural soils.

This study focusses on the geological formations of the Alfallé massif located approximately 75km east of the town of N'Goura, in the Hadjer-Lamis Province of Chad (13°N, 17°E), and their ability to provide good quality aggregates in an area with poor hard rock ressources. We investigated the petrographic and mechanical characteristics of these formations in a resource perspective. The massif is made up of three lithologies: alkali feldspar megacrystalline granite, biotite-rich fine grained quartz monzonite and biotite-rich fine grained gneiss. Alkali feldspar megacrystalline granite is composed of quartz (30%), orthoclase (30%), plagioclase (20%), biotite (15%) and opaque minerals (≈5%). Micro-monzonite is composed of quartz (15-20%), orthoclase (20-25%), plagioclase (18-25%), biotite (20-25%) and opaque minerals (≈4%). The biotite gneiss is composed of quartz (25-30%), alkali feldspars (25-27%), plagioclase (17%), biotite (25-27%) and opaque minerals (≈5%). The mechanical characteristics of the aggregates show that the aggregates studied have specific density values of between 2.58 and 2.75g/cm3 with an average value of 2.66g/cm3, a Los-Angeles coefficient of 11.2% to 28.9% with an average value of 20.1% and a wet Micro-Deval coefficient of 5.2% to 10.8% with an average value of 7.6%. The values obtained indicate that the materials studied have excellent to satisfactory properties, and that Alfallé massif provide the best characteristics among six different quarrying area in Central Chad. We propose that such rare residual reliefs within the mega-Chad paleolake area reach optimal mechanical properties through a natural selection process, specific of the paleolake erosional conditions.

Geopolymer concrete (GPC) represents an innovative green and low-carbon construction material, offering a viable alternative to ordinary Portland cement concrete in building applications. However, existing studies tend to overlook the recyclability aspect of GPC for future use. Various structural applications necessitate the use of concrete with distinct strength characteristics. The recyclability of the parent concrete is influenced by these varying strengths. This study examined the recycling potential of GPC across a spectrum of strength grades (40, 60, 80 and 100 MPa, marked as C40, C60, C80 and C100) when subjected to freeze-thaw conditions. The cementitious material comprised 60% metakaolin and 40% slag, with natural gravel serving as the coarse aggregate, and the alkali activator consisting of sodium hydroxide solution and sodium silicate solution. The strength of the GPC was modulated by altering the Na/Al ratio. After 350 freeze-thaw cycles, the GPC specimens underwent crushing, washing, and sieving to produce recycled geopolymer aggregates (RGAs). Subsequently, their physical properties and microstructure were thoroughly examined. The findings indicated that GPC with strength grades of C100, C80, and C60 were capable of enduring 350 freeze-thaw cycles, in contrast to C40, which did not withstand these conditions. RGAs derived from GPC of strength grades C100 and C80 complied with the criteria for Class II recycled aggregates, whereas RGAs produced from GPC of strength grade C60 aligned with the Class III level. A higher strength grade in the parent concrete correlated with enhanced performance characteristics in the resulting recycled aggregates.

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (<0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (>2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.