Optimization using Genetic Algorithms (GA) is a well-known strategy in several scientific disciplines. The crossover is an essential operator of the Genetic Algorithm. It has been an active area of research to develop sustainable forms for this operand. In this work, a new crossover operand is proposed. This operand depends on giving an elicited description for the chromosome with a new structure for alleles of the parents. It is suggested that each allele has two attitudes, one attitude differs contrastingly with the other, and both of them complement the allele. Thus, in case of one attitude is good, the other should be bad. This is suitable for many systems which contain admired parameters and unadmired parameters. The proposed crossover would improve the desired attitudes and damp the undesired attitudes. The proposed crossover can be achieved in two stages: the first stage is a mating method for both attitudes in one parent to improving one attitude at the expense of the other. The second stage comes after the first improvement stage for mating between different parents. Hence, two concurrent steps for improvement would be applied. Simulation experiments for the system shows improvement in the fitness function. The proposed crossover could be helpful in different fields, especially to optimize routing algorithms and network protocols, an application that has been tested as a case study in this work.

Despite the increasing role of machine learning in various fields, very few works considered artificial intelligence for frequency estimation (FE). This work presents a comprehensive analysis of deep-learning (DL) approach for frequency estimation of single-tones. It is shown that DL network with two layers having a few nodes can estimate frequency more accurately than well-known classical techniques. The study is comprehensive, filling gaps of existing works, where it analyzes error under different signal-to-noise ratios, numbers of nodes, and numbers of input samples; also, under missing SNR information. It is found that DL-based FE is not significantly affected by SNR bias or number of nodes. DL-based approach can work properly using minimal number of input nodes N at which classical methods fail. It is possible for DL to use as little as two layers with two or three nodes each, with complexity of O{N} versus O{Nlog2 (N)} for DFT-based FE, noting that less N is required for DL. Hence, DL can significantly reduce FE complexity, memory, cost, and power consumption, making DL-based FE attractive for resource-limited systems like some IoT sensor applications. Also, reduced complexity opens the door for hardware-efficient implementation using short word-length (SWL) or time-efficient software-defined radio (SDR) communications.

Deep Learning (DL) and Machine Learning (ML) are widely used in many fields, but rarely used in Frequency Estimation (FE) and Slope Estimation (SE) of signals. Frequency and slope estimation for Frequency-Modulated (FM) and single-tone sinusoidal signals are essential in various applications, such as wireless communications, sonar, and radar measurements. In this work, artificial neural network (ANN) and convolutional neural network (CNN) are used in frequency and slope estimation for FM signals under Additive White Gaussian Noise (AWGN) and Additive Symmetric alpha Stable Noise (SαSN). SαS distributions are impulsive noise disturbances found in many communication environments like marine systems; their distribution lacks a closed-form Probability Density Function (PDF), except for specific cases, and infinite second-order statistic, hence Geometric SNR (GSNR) is used in this work to determine the impulsiveness of noise in a mixture of Gaussian and SαS noise processes. ANN is a machine learning classifier, designed with few layers for reducing FE and SE complexity while getting higher accuracy as compared with classical techniques. CNN is a deep learning classifier, designed with many layers for FE and SE, and proved to be more accurate than ANN when dealing with big data and finding optimal features. Simulation results show that SαS noise can be much more harmful for FE and SE of FM signals than Gaussian noise. DL and ML can significantly reduce FE complexity, memory cost, and power consumption, which is important in many systems such as some Internet of Things (IoT) sensor applications. After training DCNN for frequency and slope estimation of LFM signals, the performance of DCNN (in terms of accuracy) can give acceptable results at very low signal-to-noise ratios where TFD fails, giving more than 20dB difference in the GSNR working range.

An adaptive deep neural network is used in an inverse system identification setting to approximate the inverse of a nonlinear plant with the aim of constituting the plant controller by copying to the latter the weights and architecture of the converging deep neural network. This deep learning (DL) approach to the adaptive inverse control (AIC) problem is shown to outperform adaptive filtering techniques and algorithms normally used in adaptive control, especially when the plant is nonlinear. The deeper the controller the better the inverse function approximation, provided that the nonlinear plant have an inverse and that this inverse can be approximated. Simulation results prove the feasibility of this DL-based adaptive inverse control scheme. The DL-based AIC system is robust to parameter change of the nonlinear plant in that, under such change, the plant output reassumes the value of the reference signal considerably faster than with the adaptive filter counterpart of the deep neural network. Settling times and rise times of the step response are shown to improve in the DL-based AIC system.

This work combines compressive sensing and short word-length techniques to achieve localization and target tracking in wireless sensor networks with energy-efficient communication between the network anchors and the fusion center. Gradient descent localization is performed using time-of-arrival (TOA) data which are indicative of the distance between anchors and the target thereby achieving range-based localization. The short word-length techniques considered are delta modulation and sigma-delta modulation. The energy efficiency is due to the reduction of the data volume transmitted from anchors to the fusion center by employing any of the two delta modulation variants with compressive sensing techniques. Delta modulation allows the transmission of one bit per TOA sample. The communication energy efficiency is increased by RⱮ, R≥1, where R is the sample reduction ratio of compressive sensing and Ɱ is the number of bits originally present in a TOA-sample word. It is found that the localization system involving sigma-delta modulation has a superior performance to that using delta-modulation or pure compressive sampling alone, in terms of both energy efficiency and localization error in the presence of TOA measurement noise, owing to the noise shaping property of sigma-delta modulation.

Frequency estimation of a single sinusoid in colored noise has received a considerable amount of attention in the research community. Taking into account the recent emergence and advances in compressive covariance sensing (CCS), the aim of this work is to combine the two disciplines by studying the effects of compressed measurements of a single sinusoid in moving-average (MA) colored noise on its frequency estimation accuracy. CCS techniques can recover the second-order statistics of the original uncompressed signal from the compressed measurements, thereby enabling correlation-based frequency estimation of single tones in colored noise using higher-order lags. Acceptable accuracy is achieved for moderate compression ratios and for a sufficiently large number of available compressed signal samples. It is expected that the proposed method would be advantageous in applications involving resource-limited systems such as wireless sensor networks.

Training data for a deep learning (DL) neural network (NN) controller are obtained from the input and output signals of a conventional digital controller that is designed to provide the suitable control signal to a specified plant within a feedback digital control system. It is found that if the DL controller is sufficiently deep (four hidden layers), it can outperform the conventional controller in terms of settling time of the system output transient response to a unit-step reference signal. That is, the DL controller introduces a damping effect. Moreover, it does not need to be retrained to operate with a reference signal of different magnitude, or under system parameter change. Such properties make the DL control more attractive for applications that may undergo parameter variation, like sensor networks.