Microwave Power Modules (MPM) are high power devices largely used for radar applications. An MPM is a hybrid combination of a Solid-State Power Amplifier (SSPA) as a driver and a Traveling wave tube amplifier (TWT) as the final high power stage. Power equalizer is often used to flat the TWT output power gain owing to its big gain fluctuations in the operating frequency range. This paper deals with an optimal design and development of a fully-coaxial easy-tunable power equalizer for an X-band MPM. The structure utilizes a coaxial waveguide as the main transmission line and a coaxial cavity loaded with absorbing material as the resonant unit. A sensitivity analysis of the coaxial cavity length, the thickness of the absorbing disc and inserted depth of the probe on the attenuation amplitude and resonant frequency is carried out. The transmission characteristic curves and the voltage standing wave ratio curves show a good compromise in terms of transferred power and adaptive matching impedance at the input and output ports. The measured results show that the equalization curve meets the requirements well and prove that this structure is practical and effective.

This paper presents a comparison between rain gauges, C-band and X-band radar data over an instrumented and regulated catchment of the Paris region, as well as their respective hydrological impacts with the help of flow observations and a semi-distributed hydrological model. Both radars confirm the high spatial variability of the rainfall down to their space resolution (respectively one kilometer and 250 m) and therefore underscore limitations of semi-distributed simulations. The use of the polarimetric capacity of the Météo-France C-band radar was limited to corrections of the horizontal reflectivity and its rainfall estimates are adjusted with the help of a rain gauge network. On the contrary, neither calibration was performed for the polarimetric X-band radar of the Ecole des Ponts ParisTech (below called ENPC X-band radar), nor any optimization of its scans. In spite of that and the non-negligible fact that the catchment was much closer to the C-band radar than to the X-band radar (20 km vs. 40 km), the latter seems to perform at least as well as the former, but with a higher scale resolution. This characteristic was best highlighted with the help of a multifractal analysis of the respective radar data, which also shows that the X-band radar was able to pick up a few extremes that were smoothed out by the C-band radar.

Current satellite remote sensing methods struggle to detect and map forest degradation, a critical issue as it is likely a major and growing source of carbon emissions and biodiveristy loss. TanDEM-X InSAR phase height (hϕ) is a promising variable for measuring forest disturbances, as it is closely related to mean canopy height, and thus should decrease if canopy trees are removed. However, previous research has focused on relatively flat terrain, despite the fact that much of the worlds’ remaining tropical forests are found in hilly areas, and this inevitably introduces artifacts in sideways imaging systems. In this paper, we find a relationship between hϕ and aboveground biomass change in four selectively logged plots in a hilly region of central Gabon. We show that minimising the level of multilooking in the interferometric processing chain strengthens this relationship, and that degradation estimates across steep slopes in the surrounding region are improved by selecting data from the most appropriate pass directions on a pixel-by-pixel basis. This shows that TanDEM-X InSAR can measure the magnitude of degradation, and that topographic effects can be mitigated if data from multiple SAR viewing geometries are available.

X-band dual-polarization phased array radar (XPAR-D) possesses high temporal-spatial resolutions and plays a significant role in detecting meso- and micro-scale convective systems. However, the precipitation attenuation it endures necessitates an effective correction method. This study selected radar data from XPAR-D at the peak of Maofeng Mountain in Guangzhou during May 16-17, 2020 from three precipitation stages after quality control. Attenuation coefficients are calculated for different precipitation types through scattering simulations of raindrop size distribution (RSD) data. Drawing upon this, an attenuation correction algorithm (MZH-KDP method) is proposed for radar reflectivity factor (ZH) according to different raindrop types, and is compared to the ZH-KDP method currently in use. The results indicate that the attenuation amount of XPAR-D echoes depends on the attenuation path and echo intensity. When the attenuation path is shorter and the echo intensity is weaker, the amount of attenuation and correction is smaller. Difficulties arise when there are noticeable deviations in such a situation, which are challenging to solve via attenuation correction methods. Longer attenuation paths and stronger echoes highlight the advantages of the MZH-KDP method, while the ZH-KDP method tends to overcorrect the bias. The MZH-KDP method outperforms the ZH-KDP method for different precipitation types. The superior correction capability of the MZH-KDP method provides a significant advantage in improving the performance of XPAR-D for the detection of extreme weather.

The reduction of Ce cations in CeO2 can be enhanced by its partial substitution by Fe cations. The enhanced reduction of Ce cations results in a considerable increase in the reaction rates for thermal water splitting reaction when compared to CeO2 alone. This mixed oxide has a smaller crystallite size when compared to CeO2 in addition to a smaller lattice size. In this work, two Fe-substituted Ce oxides are studied (Ce0.95Fe0.05O2 and Ce0.75Fe0.25O2) by core and valence level spectroscopy in their as-prepared and Ar-ions sputtered states. Ar-ions sputtering substantially increases Ce4f lines at about 1.5 eV below the Fermi level. In addition, it is found that the XPS Ce5p/O2s ratio is sensitive to the degree of reduction, most likely due to a higher charge transfer from the oxygen to Ce ions upon reduction. Quantitatively it is also found that XPS Ce3d of the fraction of Ce3+ (uo, u’ and vo, v’) formed upon Ar-ions sputtering and the ratio Ce5p/O2s lines are higher for reduced Ce0.95Fe0.05O2 than for reduced Ce0.75Fe0.25O2. XPS Fe2p showed however no preferential increase for Fe3+ reduction to Fe0 with increasing time for both oxides. Since water splitting was higher on Ce0.95Fe0.05O2 when compared to Ce0.75Fe0.25O2, it is inferred that the reaction centers for the thermal water splitting to hydrogen are the reduced Ce cations and not the reduced Fe cations. These reduced Ce cations can be tracked by their XPS Ce5p/O2s ratio in addition to the common XPS Ce3d lines.

In the current manuscript we assess to what extent X-ray photoelectron spectroscopy is a suitable tool for probing the dipoles formed at interfaces between self-assembled monolayers and metal substrates. To that aim, we perform dispersion-corrected, slab-type band-structure calculations on a number of biphenyl-based systems bonded to a Au(111) surface via different docking groups. In addition to changing the docking chemistry (and the associated interface dipoles), also the impacts of polar tail-group substituents and varying dipole densities are investigated. We find that for densely-packed monolayers the shifts of the peak positions of the simulated XP-spectra are a direct measure for the interface dipoles. In the absence of polar tail-group substituents they also directly correlate with adsorption-induced work-function changes. At reduced dipole-densities this correlation deteriorates, as work function measurements probe the difference between the Fermi-level of the substrate and the electrostatic energy far above the interface, while core level shifts are determined by the local electrostatic energy in the region of the atom from which the photoelectron is excited.

An equation for the Fermi level of impurity isotropic semiconductors is considered when the bottom of the conduction band and the top of the valence band are at the center of the first Brillouin zone. The energy of charge carriers in the valence and conduction bands of semiconductors is considered taking into account the real positions of the top of the valence band and the bottom of the conduction band in the first Brillouin zone. A universal equation for determining the Fermi levels of impurity isotropic semiconductors is presented.

Balanced nitrogen (N) and phosphorus (P) rates coupling with rational fertilization methodology could promote crop N accumulation, N use efficiency and yield production, particularly in semi-arid and arid regions. To test these characteristics, a two-year (2018 and 2019) pot experiment was therefore performed by growing summer maize in a rain-proof glass greenhouse, under 9 combined N (112, 150 and 187 kg ha-1, urea) and P (45, 60, 75 kg ha-1, calcium superphosphate) rates and three contrasting fertilizer placements. The fertilizers were placed by broadcast on soil surface (Broadcast), side band on 4 cm strip soil surface within 7 cm from sowing line (Side band) and deep band on 4 cm strip below 7 cm soil depth within 7 cm from sowing line (Deep band). Results from three maize growth stages (eight-leaf, 45 days after sowing, DAS; tasseling, 60 DAS; and harvest, 115 DAS) showed that leaf, stem, root N accumulation and total soil N were significantly increased under Deep band than under both Side band and Broadcast at N150P60, N187P60, N150P75 and N187P75, but not at N112P45, N150P45, N187P45, N112P60 and N112P75. Significantly greater leaf, stem, and root N accumulations were also displayed at N150 and N187 than at N112 for the same P60 or P75 under Deep band at 60 DAS and 115 DAS, while were for leaf and stem N accumulations at P75 and P60 than at P45 for the same N150 under Deep band at 45 DAS, 60 DAS and 115 DAS. Significantly greater agronomy N use efficiency, partial factor productivity and N use efficiency exhibited under Deep band than under Side band and Broadcast at N150P75 and N187P75, but at N150P60 and N187P60 for NUE only. In addition, leaf, stem, seed, root N concentrations positively correlated with their own N accumulations or soil N concentration at tasseling and harvest stages. Our results demonstrate that a synchronized N150P60, N187P60, N150P75 or N187P75 fertilization rate with Deep band placement can improve soil N availability and root N uptake, and hereby greater aboveground N accumulation, N use efficiency and yield production of maize particularly practical for small-holder farmers globally.

Equal-Channel Angular Pressing (ECAP) is a method used to introduce severe plastic deformation into a metallic billet without changing its geometry. In special cases strain localization occurs and a pattern consisting of regions with high and low deformation (so-called shear and matrix bands) can emerge. This paper studies this phenomenon numerically adopting two-dimensional finite element simulations of one ECAP pass. The mechanical behavior of aluminum is modeled using phenomenological plasticity theory with isotropic or kinematic hardening. The effects of the two different strain hardening types are investigated numerically by systematic parameter studies: While isotropic hardening only causes minor fluctuations in the plastic strain fields, a material with high initial hardening rate and sufficient strain hardening capacity can exhibit pronounced localized deformation after ECAP. The corresponding finite element simulation results show a regular pattern of shear and matrix bands. This result is confirmed experimentally by ECAP-processing of AA6060 material in a severely cold worked condition, where microstructural analysis also reveals the formation of shear and matrix bands. Excellent agreement is found between the experimental and numerical results in terms of shear and matrix band width and length scale. The simulations provide additional insights regarding the evolution of the strain and stress states in shear and matrix bands.

In Taiwan, peanuts are classified by hand. The kernel quality is judged based on the appearance of peanuts. The identification takes considerable time and labor. Fatigue can induce misrecogni-tion or grade cognition instability due. Peanut defects are generally divided into health, underde-velopment, insect bite, and rupture. This study employed two imaging methods push-boom FX10 and Snapshot. Deep learning was used to detect peanut defects. A push-broom instrument was used for testing. There were 1,560 peanuts, including 240 good and 240 bad ones. There were a total of 1,080 good peanuts and bad peanuts in the test set data, the band selection was used, and a CNN model was built. Based on the results from three methods, 3DCNN could classify with 97%accuracy. The Snapshot was used to achieve the real-time design of a lightweight CNN model. Finally, five bands were selected using PCA, and the screening could be accurate and efficient. The maximum overall accuracy was about 98.5%. Kappa was 97.3% with real-time recognition. This will be a major advantage in the future practical application and commercialization processes. This technique can reduce labor costs, achieve intelligent detection and intelligent grading, and bring breakthroughs to smart agriculture for other crops as well.

We investigate the tunneling of quasiparticles through a potential barrier of finite height and width, in a system with a band structure consisting of a quadratic band crossing point (QBCP). We compute the results of the transmission coefficient at various incident angles, and also the conductivity and the Fano factor. We discuss the distinguishing signatures of these transport properties in comparison with other semimetals, as well as electrons in normal metals.

Remote sensing data and techniques utilized for various purposes including natural disasters such as earthquake as well as flood. The research aims to consume liberates Landsat 8 images for investigating crashed airplanes such as MH370. Overall approximately 300 Landsat images with less than 10% clouds utilized in addition processed through Google Engine Platform. Due to the materials as well as the color of airplane body different from the area which is a plane crashed there, moreover, it should be the characteristics of the plane shapefile different in terms of albedo, temperature as well as vegetation index value. The research observed Landsat 8 data as well as methods utilized in this research, especially, NDVI, albedo in addition to band 4, capable to distinguish between the plane and its surrounding green area. Therefore, our result confirms during the research period, there was no plane on the location as well as MH370 not crashed in this site.

Hydroxyapatite (HAP) is the main mineral component of bones and teeth. It is widely used in medicine as a bone filler and coating for implants to promote new bone growth. Ion substitutions into the HAP structure highly affect its properties. One of the important substituents is manganese. This paper presents the new results obtained by high-precision density functional theory calculations using hybrid functionals, for studies of the Mn/Ca substitutions in HAP in a wide manganese concentration range within 2x2x2 supercell model. The experimental data on the mechanochemical synthesis of HAP-Mn samples with different Mn concentrations are also presented. The comparison between experiment and theory showed good agreement: the HAP-Mg unit cell parameters and volume decrease with increasing degree of Mn/Ca substitution. It is shown that electronic energy levels appear inside the band gap Eg of HAP, which depend on the concentration of Mn and change the photo-excitation energy of HAP, making its effective value Eg* less than the band gap Eg, and generally changing the photoelectronic properties of HAP. It was established that the energies of formation of the substitutions Mn/Ca depend on the position of the Ca atom (Ca1 or Ca2) and on the concentration of manganese. It has been shown that the replacement of calcium cations with manganese occurs predominantly at the Ca2 position.

Examining forbidden reflections provides valuable information on electronic states and the local environment of resonant atoms in crystals. Experimental studies of two forbidden reflections 002 and 100 in TeO₂ single crystals were performed at photon energies close to the L₁ tellurium absorption edge. It was found that the spectral form corresponding to these two reflections looks almost identical, which is completely unexpected for a highly anisotropic material. Theoretical consideration shows that only one component f_xy of the tensor describing dipole-dipole resonance scattering contributes to the 002 reflection, while two components f_xy and f_xz correspond to the 100 reflection. Numerical calculations show that the latter tensor component is comparable to the first one, but the combination of several geometric factors leads to the fact that its contribution to the spectrum is negligible. This explains the experimentally observed results. The finding shows a way for targeted investigation of single tensor components and makes it possible to compare different spectra and use them the study the physical phenomena in functional materials.

This paper proposes a compact wideband split ring resonator (SRR) based C-shaped antenna for 5G new radio (NR) band n258 millimeter wave (mm-Wave). The proposed antenna covers a wideband frequency range from 24.1 GHz to 28.3 GHz with a reflection coefficient below -10 dB. Stubs are used at each C-shaped element for impedance matching of the antenna. The proposed antenna comprises SRRs with stubs to increase the bandwidth and gain simultaneously for better performance in mm-Wave applications. A simple SRR structure is modeled to function as a reactive impedance surface with inductive property for frequencies less than 30.2 GHz. The proposed antenna realizes an impedance bandwidth of 16.1% and covers a wideband of 4.2 GHz (24.1 GHz -28.3 GHz). The use of stubs and SRR has improved the performance of the proposed antenna at mm-Wave frequencies. Specifically, the deployment of the SRR is able to produce an improved gain for the overall direction of the antenna. The simulation and measured results agree well and maintain a 7.49 dBi gain with a bandwidth of 4.2 GHz. An average efficiency of 90% can be attained in the operating range of the antenna. The designed antenna is applicable for 5G NR Band n258.

The antibodies targeting invasive proteins of Plasmodium falciparum (Pf) merozoites is a clever strategy against malaria parasite. The recent finding that Plasmodium merozoites surface enolase is a target for growth neutralizing antibodies has generated interest in identifying its re-ceptor (s) on erythrocytes. In the present study, several biochemical experiments were undertaken involving recombinant Pf enolase and antibody against it to search for its cognate receptor. The binding of rPfeno to erythrocytes was selectively sensitive to trypsin but resistant to neuramini-dase. Failure of yeast enolase binding to human red blood cells under similar conditions indicat-ed high specificity of parasite Pfeno. The mass spectrometric and immunological analyses of pro-teins obtained in pull downs and co-immunoprecipitation samples led to identification of band 3 as an interactor/receptor for Plasmodium enolase. Structural characterization of sequences of band 3 - rPfeno interacting regions revealed C-terminal exocytic regions of band 3 to be binding to Pfeno. Similarly, band 3 binding regions of rPfeno were also identified. Identification of receptor-ligand (band 3: Pfeno) pair paves the way for antimalarial anti-Pf enolase-based vaccine, anti-Pf enolase antibodies as drug and also for developing novel small molecule-based invasion inhibi-tory therapeutics including peptidomimetics that could disrupt the band 3: Pfeno protein-protein interactions.

ZnO was synthesized by Sol gel method using zinc nitrate as precursor at different calcination temperatures. Nucleation of ZnO crystallites and their growth with rise in temperature was observed. Exciton bands and lattice imperfections affected the absorption spectra. The decrease in band gap with temperature was due to the formation of defect energy levels. Phonon assisted non-radiative transitions caused broadening of the peaks. The possibility of tuning the band gap of ZnO by changing the temperature was explored. Simulation studies showed transition to single phase with rise in temperature.

This paper presents the development of a new system designed to measure the local temperature field in adiabatic shear band. Transient temperature field are simultaneously recorded by an array of 32 InSb infrared (IR) detectors and a streak camera working in visible-near infrared (VIS-NIR). Observations in IR offer a low temperature detection limit (350°C) but they are highly sensitive to uncertainty in the emissivity. Observations in VIS-NIR allow for measurement only at high temperatures (750°C) but they are less affected by uncertainty on emissivity and present a higher temperature sensitivity. By performing simultaneous measurements, it is possible to obtain data on a large temperature range with an improved accuracy at high temperature. The different sources of errors caused by uncertainty in the emissivity, spatial and temporal resolution of the detectors has been analyzed and an estimation of the total measurement uncertainty of the system is given.

In a world where conventional sources of energy are fast depleting, the quest for alternative energy sources may hold the key for the survival of humanity. In the present work, emphasis has been given to the idea of producing energy from perovskite based solar cells. In order to bring this idea into fruition, a unique and novel nano structured perovskite material n-propyl ammonium lead chloride (C₃H₇NH₃⁺PbCl₃⁻) was prepared through a unique co-precipitation route using n-propyl amine (n-C₃H₇NH₂) and hydrochloric acid as the starting precursors with aqueous solution of Pb(CH₃COO)₂3H₂O. Finally acetic acid was added to the solution and this solution was allowed to concentrate and then gradually cooled down to room temperature. After math, the synthesized material was spin-coated on TiO₂ film to fabricate the solar cell. The device was then undergone systematic analysis using XRD, SEM, UV and Photo Conversion to get a transparent idea regarding its structural, electrical and optical properties. When experimentally applied, this perovskite-based solar cell has shown energy conversion efficiency (η) of around 6.01 % which is noticeably good. Thus it can be concluded that this material is promising for fabrication of vastly efficient solar cells. This technology can be tried in large scale as an alternative of conventional energy in the near future.

Recently L-shaped tunneling field-effect-transistor (LTFET) has been introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, shortcoming of LTFET was investigated. It was found that corner effect present in LTFET effectively degrades its subthreshold slope. To get rid of corner effect a new type of device with dual material gates is presented. The new device termed as DG-LTFET gets rid of the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over LTFET. In this work DG-LTFET was evaluated for different device parameters, and bench-marked against LTFET. This work presents an optimum configuration of DG-LTFET in terms of device dimensions and doping levels, to get the best subthreshold, ON current and ambipolar performance from the DG-LTFET.

On-chip integration of two-dimensional (2D) materials with unique structures and distinctive properties endow integrated devices with new functionalities and improved performance. With a high flexibility in modifying its properties and a strong compatibility with various integrated platforms, graphene oxide (GO) becomes an attractive 2D material for implementing functional hybrid integrated devices. Here, we demonstrate novel functionalities that go beyond the capabilities of conventional photonic integrated circuits, by harnessing the photo-thermal effects in 2D GO films integrated onto them. These include all-optical control and switching, optical power limiting, and non-reciprocal light transmission. The 2D layered GO films are on-chip integrated with precise control of their thicknesses and sizes. Benefitting from the broadband response of 2D GO films, all the three functionalities feature a very wide operational bandwidth. By fitting the experimental results with theory, we also extract the changes in material properties induced by the photo-thermal effects, which reveal interesting insights about 2D GO films. These results highlight the versatility of 2D GO films in implementing functional integrated photonic devices for a range of applications.

Based on the high-precision quantitative measurement ability, the S-band subsystem of China's high- resolution aviation system carried out the agricultural application test for the first time in Jilin elm, China. The experiment is mainly carried out in combination with vegetation growth, soil moisture content inversion, wheat straw returning and ground feature classification. Through the design of quantitative measurement scheme, the results of different straw coverage and observation at different times are compared, which shows the prospect of S-band full polarization synthetic aperture radar system in the field of agricultural application.

Metal plasmonic nanostructures have promising applications in biosensing due to their ability to facilitate light-matter interaction. However, the damping of the metal leads to a wide full width at half maximum (FWHM) spectrum and results which restricts its sensing capabilities. In this research, we present a novel non-full-metal nanostructure, namely indium-tin oxide (ITO)-Au nanodisk arrays consisting of top ITO nanodisk arrays and a bottom gold layer, and compare the coupling mode with the full-metal nanodisk arrays. The FWHM of proposed ITO-Au nanodisk array reduces to one fifth of that all metal nanodisk arrays, which is generated mode-coupling by surface plasmon modes at metal interfaces with magnetic resonance mode. Furthermore, the thickness variation of nanodisks has no impact on the sensing performance of this ITO-based nanostructure, ensuring excellent tolerance during preparation. We fabricated both structures by using template transfer and vacuum deposition techniques and calibrated their sensing performances by detect Immunoglobulin G (IgG) protein molecules. Both theoretical and experimental results demonstrate that ITO-Au nanodisk arrays provide an effective solution for biosensing applications.

All-optical signal processing based on nonlinear optical devices is promising for ultrafast information processing in optical communication systems. Recent advances in two-dimensional (2D) layered materials with unique structures and distinctive properties have opened up new avenues for nonlinear optics and the fabrication of related devices with high performance. This paper reviews the recent advances in research on third-order optical nonlinearities of 2D materials, focusing on all-optical processing applications in the optical telecommunications band near 1550 nm. First, we provide an overview of the material properties of different 2D materials. Next, we review different methods for characterizing the third-order optical nonlinearities of 2D materials, including the Z-scan technique, third-harmonic generation (THG) measurement, and hybrid device characterization, together with a summary of the measured n₂ values in the telecommunications band. Finally, the current challenges and future perspectives are discussed.

The unfolded band structure and optical properties of Cu-doped KCl crystals were computed by first principles within the framework of density functional theory, implemented in the ABINIT electronic structure package utilizing pseudopotential approximation and a plane-wave basis set. From a theoretical point of view, Cu substitution into pristine KCl crystals requires calculation by the supercell (SC) method. This procedure shrinks the Brillouin zone, resulting in a folded band structure that is difficult to interpret. To solve this problem and gain insight into the effect of copper ions (Cu+) on electronic properties, the band structure of SC KCl:Cu was unfolded to make a direct comparison with the band structure of the primitive cell (PC) of pristine KCl. To understand the effect of Cu substitution on optical absorption, we calculated the imaginary part of the dielectric function of KCl:Cu through a sum-over-states formalism and broke it down into different band contributions by partially making an iterated cumulative sum (ICS) of selected valence and conduction bands. Consequently, we identified those interband transitions that give rise to the absorption peaks due to the Cu+ ion. These transitions involve valence and conduction bands formed by the Cu-3d and Cu-4s electronic states

A good optical quality crystal of 2-aminopyridine (2AP) metal complex crystals was grown by slow evaporation technique at room temperature. The transparent and defect less bulk size of 2-aminopyridine potassium dihydrogen orthophosphate metal complex crystals have been grown by solution growth method. The molecular structure and morphology of grown crystals was drawn and planes are indexed using WINXMORPH software. A optical absorption spectrum, the UV cut-off wavelength, Band gap (Eg), Reflectance (R), Refractive Index (n), Extinction coefficient (K) and Electrical susceptibility (χc) are calculated for 2AP metal complex crystals.

Possibilities of utilization of two frequencies synthetic aperture radar (SAR) operating simultaneously in P-band and S or L-band are considered. Advantages of such system are shown. They are caused by improvement of data interpretation and by decrease of ionosphere influence. Tasks of surface and subsurface sensing by the complex SAR were under investigation for vegetation, soil covers are given. As an example, the investigation results of coniferous forest areas backscattering by the spaceborne P-band SAR together with L-band SAR in the September-February period are presented. Studies have shown that the joint use of the results in L and P bands offer unique opportunities to explore the effects of changes in the backscattering properties of forest surfaces.

By using 0.35-um CMOS process, this work achieves a design of analogous band-gap reference voltage circuit with low temperature coefficient. The proposed circuit operates at 3V and generates a reference current of 44 uA. The HSPICE simulation results show the temperature coefficient of this circuit is 23 ppm/℃ at range of -10 ℃ to 100 ℃, and the line regulation (the ratio of output current variation to supply voltage variation) is estimated as 1.95 uA/V from supply voltage variation of 3 V to 5 V. The experimental chip is fabricated and measured. The circuit provides adjustable capability for output voltage among temperature variation of -10 - 100 ℃. The chip area is 534 × 695 um^2. In this new design, the operational amplifier is not necessary. The chip design effort can be great reduced.

We report a novel dual-band barrier infrared detector (DBIRD) design using type-II superlattices (T2SLs). The DBIRD structure consists of back-to-back barrier diodes: a "blue channel" (BC) diode which has an nBp architecture, an n-type layer of larger bandgap for absorbing blue band infrared/barrier/p-type layer, and a "red channel" (RC) diode which has an pBn architecture, a p-type layer of smaller bandgap for absorbing red band infrared/barrier/n-type layer. Each has a unipolar barrier using a T2SL lattice matched to a GaSb substrate to impede the flow of majority carriers from the absorbing layer. Each channel in the DBIRD can be independently accessed with a low bias voltage, as is preferable for high-speed thermal imaging. Device modeling of DBIRDs and simulation results of the current-voltage characteristics under dark and illuminated conditions are also presented. They predict that dual-band operation of the DBIRD will produce low dark currents and 27-33% quantum efficiencies for the in-band photons in the BC with λc=5.58 μm, and a nearly-constant 33% in the RC with λc=8.05 μm. The spectral quantum efficiency of the BC for 500 K blackbody radiation is approximately 20% over the range of λ=3 − 4.2 μm, while that of the RC has a peak of 42% at 5.7 μm. The DBIRD may provide improved high-speed dual-band imaging in comparison with NBn dual-band detectors.

The analysis of autosomal polymorphism (STR) or Y chromosome polymorphisms (Y-STR) are usually used for the study and deconvolution of mixed DNA profiles in forensic genetics, accompanying data interpretation with biostatistical evaluations (e.g. RMP, RMNE, LR). Sometimes, however, some mixed DNA profiles are so complex that the autosomal and Y markers do not allow a correct discrimination and identification. In this work is reported a robbery case in which the analysis of the polymorphic markers of the X chromosome was applied to the mixed profiles obtained from the traces, thus falling outside the classic relationship use of the X-STRs. The aim of the authors is, in fact, to encourage the classic use of X-STRs not only in parental relationships, but also in purely forensic cases for interpreting complex mixed DNA profiles. Their application in case resolution could be more decisive than STR/Y-STR.

This study presents a tri-layer broadband metamaterial absorber which operates in the GHz range. The absorber was composed of a polyhedral iron-cobalt alloy/graphite nanosheet material arranged in a flat sheet with two punched-in rings for the top layer, a continuous FR-4 layer at the middle, and a continuous copper layer at the bottom. For the normal incidence of electromagnetic wave, the proposed absorber demonstrated an exceptional broadband absorption in a frequency range of 7.9-14.6 GHz, revealing an absorption exceeding 90%. The absorption magnitude remains to be above 90% in a frequency range of 8-11.1 GHz for transverse-electric-polarized waves at incident angles up to 55°. For both transverse-magnetic- and electric-polarized waves, the absorption exceeds 90% in a frequency range of 9.5-14.6 GHz. The physical mechanism behind the absorption properties is analyzed thoroughly through the electric- and magnetic-field distributions. The obtained results could contribute potentially to the development of microwave applications based on metamaterial absorbers, such as radar-stealth technology, electromagnetic shielding for health safety and reduced electromagnetic interferences for high-performance communications and electronic devices.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

The impact of large atmospheric attenuation events on data quality and availability is a critical aspect for future altimetry missions based on Ka-band altimetry. The SARAL/AltiKa mission and its Ka-band nadir altimeter offer a unique opportunity to assess this impact. Previous publications (Tournadre et al. 2009, 2015) already analyzed the impact of rain on the waveforms at Ka-band and proposed a definition of an elaborate rain flag. This notion tends to give a simpler black and white view of the atmospheric attenuation when the effect on the altimeter measurement is intense. But in practice, there is continuum of measurements that may be partially distorted or corrupted by rain events. The present study proposes a wider point of view , the ACECAL approach providing statistics on rain cells occurrences as well as their amplitude and their size, as guidelines for future Ka-band missions concerning the impact of the atmosphere. At global scale, 1 % of the measurements are affected by an attenuation larger than 23 dB and 10 % of the atmospheric attenuation events have a size larger than 40 km. This study demonstrates that the data quality and availability over some regions of particular interest for oceanography as Gulf Stream, North Pacific and Brazil currents could be affected compared to global statistics. It also opens some perspectives on the benefits that the community could be drawn from the systematic distribution of the rain cells parameters as secondary products of altimetry missions.

Why do stretched rubber bands not hit the hand after ejection? What is the mechanism behind the rubber band ejection dynamics? These questions represent a fascinating scientific problem. Because the size of a rubber band in the circumferential direction is much larger than that in the other two directions of its cross-section, we regard the rubber band as a slender beam and establish a mathematical model of the dynamics of the rubber band stretching and ejection. Furthermore, we obtain the dependence of the dynamic curvature of the rubber band on the arc length and time. We used the finite element software ABAQUS to simulate the dynamic process of a rubber band stretching and ejection. The simulation results and dimensional analysis were performed to examine the effect of the bending elastic rebound velocity. The mathematical model and simulation results revealed that the relationship between the curvature and time at the end of the rubber band ($s =0$) was as follows: $\kappa\sim t^{-{1}/{2}}$. This research has guiding significance for the design of rubber bands as elastic energy storage devices.

A series of Ti₄₀Zr₂₅Cu₉Ni₈Be₁₈)_100-xTM_x (x = 0, 1, 2, 3, 4 at.%, TM = Nb, Y) Bulk amorphous alloys were designed and prepared using the copper mold casting method. The microstructures, glass forming ability and mechanical properties of the alloys were investigated by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning colorimetry (DSC), depth-sensitive nanoindentation and uniaxial compressive test. The Bulk amorphous alloys with different ductility were investigated by measuring their plastic deformation energy (PDE) of the first pop-in events during loading. The relationships between the PDE value, shear band formation and ductility in Bulk amorphous alloys have been investigated. The results show that the PDE value decreases by the Nb addition and promotes the generation of multiple shear bands easily, which increase the fracture strength and plasticity significantly. Substituting Nb with Y has exactly the reverse effect. A useful rule for preparing of Bulk amorphous alloys with high plasticity is herein proposed, whereby the chemical composition of the Bulk amorphous alloys can be tailored to possess a lower PDE value.

In this study, two donor-acceptor (D-A) type conjugated polymers namely PQSeCz and PQSeFl were designed and synthesized. Selenophene was incorporated as a π -bridge, quinoxaline as an acceptor unit while carbazole and fluorene were used as the donor units. Polymers were synthesized via palladium catalyzed Suzuki polymerization reaction. All molecules were characterized by 1H and 13C NMR Spectroscopy. The weight and number average molecular weights of the two polymers were determined by gel permeation chromatography (GPC). Electrochemical and spectroelectrochemical characterizations of the polymers were performed to investigate their optoelectronic properties. Oxidation potentials were 1.15 V/ 0.82 V and 1.11 V/ 0.82 V for PQSeCz and PQSeFl respectively, while reduction potentials were -1.26 V /-1.14 V and -1.48 V/ -1.23 V, respectively. In the visible region, maximum absorption wavelengths for the two polymers were 551 nm and 560 nm, respectively. Optical band gaps (Egop) were found from the lowest energy π – π∗ transition onsets as 1.71 eV and 1.58 eV, respectively. Both polymers showed good solubility in common solvents.

X-band marine radar captures signal reflected from the sea surface. Theoretical studies indicate that the initial unfiltered signal contains meaningful information including parameters related to wind waves. Traditional methods for estimating significant wave height (SWH) rely on the physical laws describing signal reflection from rough surfaces. However, recent studies suggest the feasibility of employing artificial neural networks (ANNs) for SWH approximation. Both classical and ANN-based approaches necessitate costly in situ data. In this study, we propose generating synthetic radar images with specified wind wave parameters using Fourier-based approach and Pierson–Moskowitz wave spectrum as a viable alternative. We generate synthetic images and use them for unsupervised learning approach to train a convolutional component of an ANN. After that, we train a regression ANN based on the previous convolutional component to obtain SWH back from synthetic images. Then, we apply preliminary trained weights for the same regression model to train SWH approximation on the dataset of real sea clutter images. In this study, we demonstrate the increase in the accuracy of SWH estimation from radar images with the preliminary training on synthetic data.

It is well known that X-ray crystallography is based on X-ray diffraction (XRD) by atoms and molecules. The diffraction pattern arises as a result of scattering of incident radiation, which makes it possible to determine the structure of the scattering substance. With the advent of ultrashort radiation sources, the theory and interpretation of X-ray diffraction analysis remained the same. This work shows that when an attosecond laser pulse is scattered on a DNA molecule, including during its nicking and bending, the pulse duration is an important characteristic of the scattering. In this case, the diffraction pattern changes significantly compared to the previously known scattering theory. The results obtained must be used in XRD theory to study DNA structures, their mutations and damage, since the previously known theory can produce large errors and, therefore, the DNA structure can be “deciphered” incorrectly.

Heat stress affects the yield of medicinal plants and can reduce biomass and/or metabolite production. In order to evaluate the effect of heat-induced stress on the essential oil production in Mentha x piperita L. var. Mitcham (Mitcham mint) and Mentha x arvensis var. piperascens Malinv. ex L. H. Bailey (Japanese mint), we studied the chemical composition of the oils of the two mint species under different heat shock stress in growth chambers. The antibacterial activity of the essential oils was also evaluated; microscopic observation (fluorescence and electron transmission) was used to assess the effect of the tested samples on bacterial growth. The results obtained shed light on the mint essential oils composition and biological activity in relation to heat stress.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

A printed Vivaldi antenna that is optically transparent, ultra-wideband (UWB), and reconfigurable has been developed, fabricated, and tested at millimeter wave frequencies. It covers a broad frequency range of 20-30 GHz by using three PIN diodes. The diodes control the current flow to direct the beam of the antenna. The results of numerical simulations and measurements match at millimeter wave frequencies. The design of this antenna is unique as it allows for a reduction in size and ease of integration while also providing the ability to change the radiation pattern by up to 300 degrees, making it suitable for 5G and 6G communications. Additionally, this antenna can also be useful for RF applications that require dynamic switching of radiation patterns and cognitive radio.

Extracellular vesicles (EVs) released by different cell types play significant role in many physiological and pathophysiological processes. In physiological conditions red blood cells (RBCs) derived EVs compose 4 - 8% of all circulating EVs, and oxidative stress (OS) as a consequence of different pathophysiological conditions significantly increases the amount of circulated RBC-derived EVs, however the mechanisms of EV formation are not fully defined yet. To analyze OS-induced EV formation and RBCs transformations we used flow cytometry to evaluate cell esterase activity, caspase-3 activity, and band 3 clustering. Band 3 clustering was additionally analyzed by confocal microscopy. Two original laser diffraction-based approaches were used for analysis of cell deformability and band 3 activity. Hemoglobin species were characterized spectrophotometrically. We showed that cell viability in tert-butyl hydroperoxide-induced OS directly correlated with oxidant concentration to cell count ratio, RBCs-derived EVs contained hemoglobin oxidized to hemichrome (HbChr). OS induced caspase-3 activation and band 3 clustering in cells and EVs. Importantly, we showed that OS-induced EV formation is independent from calcium. Presented data indicated that during OS RBCs eliminate HbChr by vesiculation, in order to sacrifice the cell itself thereby prolonging lifespan and delaying the untimely clearance of in all other respects healthy RBCs.

The present study uses the 3 years of data from a vertically pointed profile Radar (VPPR) at the mountain site (Huancayo at 3.2 km msl; HYO) in Peru to investigate the precipitation characteristics/patterns including diurnal variation, bright band (BB) characteristics and vertical structure of rain (VSR). VPPR provides continuous 1­min profiles of radar reflectivity (Ze), rain rate (RR), liquid water content (LWC) and Doppler velocity. At the same time, field campaign data are used to investigate the role of the surface and atmospheric variables in generating the rainfall and organization of the cloud systems over HYO. The precipitation shows the bimodal distribution; frequent and higher RR during afternoon and nighttime. The BB height also shows a diurnal pattern and BB height is higher during the afternoon and nighttime compared; and follows the diurnal heating of the Andes. More than 70% BB height lies between ~4.3­4.7 km and only 20% BB has altitude higher than 5 km. The austral summer monsoon (December to March months) have higher intense vertical profiles (higher Z e ) compared to pre monsoon seasons (September to November) and shows the nega­tive gradient for most of the altitude. The RR and LWC show the opposite characteristics, and both have a positive gradient below the 6 km altitude and then negative gradient above 6 km altitude. The raindrop size distribution (DSD) parameters show most of the variation below the freezing level, and a higher concentra­tion of large sized of hydrometeors are observed for higher RR, however the dominant modes of Dm are less than 1 mm. The changes in the VSR in DSD parameters are significant for the RR>20 mm/h, whereas for RR<2 mm/h the vertical structure in DSD parameters do not have much differences during monsoon and premonsoon seasons. Satellite and reanalysis data reveal the short periods of convective activity with higher ac­ cumulated rainfall over HYO compared to stratiform precipitation, which is more common in the nighttime and sustain for many hours. Wet spells (higher rainy days) have low pressure circulation, which favours the transport of moisture from the Amazon to the central Sierra of Peru, while the anticyclonic circulation at high levels favours the divergence at higher pressure levels and, enhances the convective in the region. During the dry spells, low level weaker circulation at the west of Brazil, restricts the transport of moisture to the central Sierra, while the circulation at high levels does not favor rain processes. The improved understanding of the tropical Andes precipitation would be very important for assessing climate variability and changes as well as to forecast precipitation using the numerical models.

In this paper, sea surface wind speed (SSWS) retrieval from Gaofen-3 (GF-3) quad-polarization stripmap (QPS) data in vertical-vertical (VV), horizontal-horizontal (HH) and vertical-horizontal (VH) polarizations is investigated in detail based on 3,170 scenes acquired from October 2016 to May 2018. The radiometric calibration factor of the VV polarization data is examined first. This calibration factor generally meets the requirement of SSWS retrieval accuracy with an absolute bias of less than 0.5 m/s but shows highly dispersed characteristics. These results lead to SSWS retrievals with a small bias of 0.18 m/s but a rather high root mean square error (RMSE) of 2.36 m/s compared with the ERA-Interim reanalysis model data. Two refitted polarization ratio (PR) models for the QPS HH polarization data are presented. Based on a combination of the incidence angle- and azimuth angle-dependent PR model and CMOD5.N, the SSWS derived from the QPS HH data shows a bias of 0.07 m/s and an RMSE of 2.26 m/s relative to the ERA-Interim reanalysis model wind speed. A linear function relating SSWS and the normalized radar cross section (NRCS) of QPS VH data is derived. The SSWS data retrieved from the QPS VH data show good agreement with the WindSat SSWS data, with a bias of 0.1 m/s and an RMSE of 2.02 m/s. We also apply the linear function to the GF-3 Wide ScanSAR data acquired for the typhoon SOULIK, which surprisingly yields a very good agreement with the model results. A comparison of SSWS retrievals among three different polarization datasets is also presented. The current study and our previous work demonstrate that the general accuracy of the SSWS retrieval based on GF-3 QPS data has an absolute bias of less than 0.3 m/s and an RMSE of 2.0 ±0.2 m/s relative to various datasets. Further improvement will depend on dedicated radiometric calibration efforts.

This paper presents an alternative process to fabricate flexible bandpass filters by using embroidered yarn conductor on electronic-textile. The novelty of the proposed miniaturized filter is its complete integration on the outfit, with benefits in terms of compressibility, stretch ability and high geometrical accuracy, opening the way to develop textile filters in sport and medicine wearable applications. The proposed design consists of a fully embroidered microstrip topology with a length equal to quarter wavelength (λ/4) to develop a bandpass filter frequency response. A drastic reduction in size of the filter was achieved by taking advantage of a simplified architecture based on meandered-line stepped impedance resonator. The e-textile microstrip filter has been designed, simulated, fabricated and measured, with experimental validation at a 7.58 GHz frequency. The insertion loss obtained by simulation of the filter is substantially small. The return loss is greater than 20 dB for bands. To explore the relations between physical parameters and filter performance characteristics, theoretical equivalent circuit model of the filter constituent components were studied. The effect of bending of the e-textile filter is also studied. The results show that by changing the radius of bending up to 40 mm, the resonance frequency is shifted up 4.25 MHz/mm.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

Detailed description of carbonate minerals different in magnesium content of Triassic dolomites were presented in this article. The tests were carried out to determine geochemical and miner-alogical features in the terms of their geoengineering properties. The following carbonate phas-es were identified: a low-Mg calcite, a high-Mg calcite, a proto-dolomite, an ordered dolomite and a huntite. The following research methods were used: microscopic analysis, X-Ray Diffrac-tion, X-Ray Fluorescence and Electron probe microanalysis. The samples were collected from the Tarnowice formation which is the lower part the profile of the Upper Muschelkalk. On the basis of the results the chemical formulas of carbonate phases were calculated. The ranges of Mg and Ca content were presented in formulas. The results indicate of Mg in low-Mg calcite ranges from 0.6 to 1.2%, in high-Mg calcite from 7.47 to 10.41%. In proto-dolomite it ranges from 10.96 to 11.78%. In ordered dolomite Mg content is stoichiometric value for dolomite – 13.18%. Due to the reduced Mg content in identified huntite (the value ranges from 13.62% to 17.76), this carbonate phase was named as de-huntite.

X-ray diffraction (XRD) analysis of complex poly-atomic systems, especially of biomolecules, using ultra-short laser pulses (USP), is currently one of the most important fields of modern physics. The basis for interpreting and "deciphering" experimental data is the well-known theory of X-ray scattering, where the main parameter of USPs - its duration - is not taken into account. In the present work it is shown that for scattering of attosecond USPs on DNA and RNA trinucleotides the pulse length is the most important scattering parameter. In this case the diffraction pattern significantly changes with respect to the previously known scattering theory. The results obtained are extremely important in XRD when using attosecond pulses to study trinucleotides of DNA and RNA because using the previously known scattering theory which does not take into account the duration of USPs one can not correctly interpret and therefore "decode" DNA and RNA structures.

Space-based Interferometric Synthetic Aperture Radar (InSAR) applications have been widely used to monitor the cryosphere over past decades. Because of temporal decorrelation, interferometric coherence often severely degrades on fast moving glaciers. In addition, higher sensitivity ambiguity occurs in large baseline configurations, which are needed for extracting topographic information over low relief areas such as the surface of a glacier. TerraSAR-X add-on for Digital Elevation Measurement (TanDEM-X) observations, which overcome the temporal decorrelation because of their simultaneous measurements by two satellite constellations, have used a short baseline sufficient for generation of excellent digital elevation models in most locations around the world. However, it remains difficult to estimate detailed topographic characteristics over low slope glacier surfaces because of the relatively less sensitive height ambiguity from the small baselines. In this study, we used the TanDEM-X pursuit monostatic mode with large baseline formation following a scientific phase timeline to develop highly sensitive topographic elevation models of the Petermann Glacier of Northwest Greenland. As expected, coherent interferometric phases (> 0.8) were well maintained over the glaciers despite their fast movement thanks to the nearly simultaneous TanDEM‐X measurements. The height ambiguity, which defined as the altitude difference correspondent to phase change of flattened interferogram, of the dataset was 10.63 m, which is favorable for extracting topography in a low relief region. We validated the TanDEM‐X derived glacial topography by comparing it to the SAR/Interferometric radar altimeter observations acquired by CryoSat‐2 and the IceBridge Airborne Topographic Mapper laser altimeter measurements. Both observations showed very good correlation within a few meters of the offsets (‐12.5 – ‐3.1 m) with respect to the derived glacial topography. Because of highly sensitive ambiguity, we could successfully extract detailed geomorphological features on the glaciers. Routine TanDEM-X observations will be very useful to better understand the dynamics of glacial movements and topographic change.

The use of spherical radial basis functions (SRBFs) in regional gravity field modeling has become popular in recent years. However, to our knowledge, their potential for combining gravity data from multiple sources, particularly data with different spectrum information in the frequency domain, has not been extensively explored. Therefore, band-limited SRBFs, which have good lo-calization characteristics in the frequency domain, are the main tool in this study. We propose a residual and a-prior accuracy comparative analysis method to determine the optimal degree of expansion of SRBFs for gravity data. Using this methodology, we constructed a high-resolution geoid model called ColSRBF2023 in Colorado. The degrees of expansion for terrestrial and airborne data were set to 5200 and 1840, respectively. Results indicate that ColSRBF2023 has a standard deviation (STD) value of 2.3 cm compared to the GSVS17 validate data. This value is 2-6 mm lower than models obtained using different degrees of expansion for gravity data and models from other institutions considered in this study. Additionally, at the 1'×1' grid in the entire target area, ColSRBF2023 has an STD value of 2.4 cm when compared to the validation model. This value is also the best among the options examined in this study. These findings highlight the importance of determining the optimal expansion degree of gravity data, particularly when constructing high-resolution gravity field models in rugged mountainous regions.

TmMgB5O10 spontaneous crystals were synthesized via flux-growth technique from a K2Mo3O10-based solvent. The crystal structure of the compound was solved and refined within the space group P21/n. The first principles calculations of the electronic structure reveal that TmMg-pentaborate is an insulator with an indirect energy band gap of approximately 6.37 eV. Differential scanning calorimetry measurements and powder X-ray diffraction studies of heat-treated solids show that TmMgB5O10 is an incongruent melting compound. A characteristic band of Tm3+ cation corresponding to the 3H6 → 1D2 transition is observed in the photoluminescence excitation spectra of TmMg-borate. The as-obtained crystals exhibit intense blue emission with the emission peaks centered at 455, 479, 667 and 753 nm. The most intensive band corresponds to the 1D2 3F4 transition.

Artemisia absinthium (A. absinthium) leaf extract was successfully used to create zinc oxide nanoparticles (ZnO NPs), and their properties were investigated via several techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), Fourier transform infrared (FTIR), and UV–Vis spectroscopy. SEM analysis confirmed the spherical and elliptical shapes of the particles. Three different zinc peaks were observed via EDX at energies of 1, 8.7, and 9.8 keV, together with a single oxygen peak at 0.5 keV. XRD analysis identified ZnO NPs as having a hexagonal wurtzite structure with a particle size that decreased from 24.39 to 18.77 nm, and with an increasing surface area (BET) from 4.003 to 6.032 m2/g for the ZnO (without extract) and green ZnO NPs, respectively. FTIR analysis confirmed the groups of molecules that were accountable for stabilizing and minimizing the ZnO NPs, which was apparent at 3400 cm. Using UV–Vis spectroscopy, the band gap energies (Egs) for the green ZnO and ZnO (without extract) NPs were estimated, and the values were 2.65 and 2.79 eV, respectively.

Point defect-based single-photon emitters (SPEs) in GaN have aroused a great deal of interest due to their room-temperature operation, narrow line width and high emission rate. The room-temperature SPEs at the telecommunication bands have also been realized recently by localized defects in GaN in experiments, which are highly desired for the practical applications of SPEs in quantum communication with fiber compatibility. However, the origin and underlying mechanism of the SPEs remain unclear to date. Herein, our first-principle calculations predict and identify an intrinsic point defect NGa in GaN that owns a zero-phonon line (ZPL) at telecommunication windows. By tuning the triaxial compressive strain of the crystal structure, the ZPL of NGa can be modulated from 0.849 eV to 0.984 eV, covering the fiber telecommunication windows from the O band to the E band. Besides the ZPL, the formation energy, band structure, transition process and lifetime of the SPEs under different strains are investigated systematically. Our work gives insight into the emission mechanism of the defect SPEs in GaN and also provides effective guidance for achieving wavelength-tunable SPEs working in fiber telecommunication windows.

This document presents the design and manufacture of a reflectarray (RA) antenna for the Ku-band, based on a fully-metallic 3D architecture. The reflectarray unit cell is formed by a square-shaped waveguide section ended in a short circuit, that is the reflectarray back ground plane. Each cell has the ability of configuring the phase of its own reflected field by means of resonators perforated on the walls of the cell waveguide section. The resonator-based waveguide cell introduces the 3D character to the design. The geometry of the resonators and its size variation introduces the phase behaviour of each cell, conforming the radiation pattern of the reflectarray. This design explores the potential of phase value truncation (6 states and 2 states), and demonstrates that proper pattern results can be obtained with this phase truncation.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

The assimilation of Soil Moisture and Ocean Salinity (SMOS) data into the ECMWF (European Centre for Medium Range Weather Forecasts) H-TESSEL (Hydrology revised - Tiled ECMWF Scheme for Surface Exchanges over Land) model is presented. SMOS soil moisture (SM) estimates have been produced specifically by training a neural network with SMOS brightness temperatures as input and H-TESSEL model SM simulations as reference. This can help the assimilation of SMOS information in several ways: (1) the neural network soil moisture (NNSM) data have a similar climatology to the model, (2) no global bias is present with respect to the model even if regional differences can exist. Experiments performing joint data assimilation (DA) of NNSM, 2 metre air temperature and relative humidity or NNSM-only DA are discussed. The resulting SM was evaluated against a large number of in situ measurements of SM obtaining similar results to those of the model with no assimilation, even if significant differences were found from site to site. In addition, atmospheric forecasts initialized with H-TESSEL runs (without DA) or with the analysed SM were compared to measure of the impact of the satellite information. Although, NNSM DA has an overall neutral impact in the forecast in the Tropics, a significant positive impact was found in other areas and periods, especially in regions with limited in situ information. The joint NNSM, T2m and RH2m DA improves the forecast for all the seasons in the Southern Hemisphere. The impact is mostly due to T2m and RH2m, but SMOS NN DA alone also improves the forecast in July- September. In the Northern Hemisphere, the joint NNSM, T2m and RH2m DA improves the forecast in April-September, while NNSM alone has a significant positive effect in July-September. Furthermore, forecasting skill maps show that SMOS NNSM improves the forecast in North America and in Northern Asia for up to 72 hours lead time.

As a part of the proposed article, the authors presented comprehensive data analysis for movement data that comes from a positioning system based on ultra-wide band (UWB) technology. For purpose of this article, a test was carried out during which the car equipped with cruise control overcame the given path at a speed from 10 km/h to 60 km/h. The obtained motion models (information about position) have been filtered through a series of filters - from fundamentals filters with a variable window (median, moving average, Savitzky-Golay filter), through more complex ones like the Wiener or Kalman filter. As a result, the authors proposed a form of data analysis and filtration depending on the speed of the moving object. In addition, the maximum accuracy that can be obtained for a given traffic model was also determined. The whole research proves that it is possible to use a system based on UWB technology in positioning objects for urban applications - smart city, in industry 4.0 applications as well as for positioning autonomous vehicles in urban applications, such as well as on highways to maintain cohesion of convoys vehicles.

When an earthquake or a large fire has occurred, it is difficult to secure communication networks for rescue in the building due to the destruction of commercial communication networks. Although analog radio systems such as VHF (very high frequency) and UHF (ultra-high frequency) are used for rescue operation in general, communication failure occurs in closed spaces, causing difficulties in smooth rescue operations. When the communication infrastructures have been destroyed in a building in the disaster, an emergency wireless telecommunication environment should be constructed to secure a safer disaster response environment. In this study, along with comparison of the performances of diverse communication frequencies, UWB (Ultra-Wide Band) wireless telecommunication networks were evaluated under five building indoor environment conditions including open spaces. UWB communication modules were fabricated to satisfy the IEEE (The Institute of Electrical and Electronics Engineers) 802.15.4a standard performance to measure distances in which communications are possible according to the indoor environment for each of six channels with different UWB communication frequencies. The results indicated that the distances in which communications are possible for each the six channels were average 15.5 m, maximum 20 m in open spaces; average 17.33 m, maximum 20 m in corridors; average 15.3 m, maximum 20 m in indoor office environments with office fixtures; average 4.33 m, maximum 6 m in vertical spaces of stairs; and average 6.5 m, maximum 17 m in closed horizontal spaces with a fire door. In this case, the communication performance and distance performance were shown to be the most excellent at a frequency (Centre Frequency) of 6489.6 and a band of 5980.3 – 6998.9 MHz, which is UWB 7ch. In conclusion, it is judged that if UWB communication modules are installed in the disaster area at intervals of 20 m and multi-channels are used, communication environments can be constructed even in closed spaces

Secondary forests (SF) are important carbon sinks, removing CO₂ from the atmosphere through the photosynthesis process and storing photosynthates in their aboveground live biomass (AGB). This process occurring at large-scales partially counteracts C emissions from land-use change, playing, hence, an important role in the global carbon cycle. The absorption rates of carbon in these forests depend on forest physiology, controlled by environmental and climatic conditions as well as on the past land use, which is rarely considered for retrieving AGB from remotely sensed data. In this context, the main goal of this study is to evaluate the potential of full polarimetric ALOS-2 PALSAR-2 data for estimating AGB by taking into account the past-land use of SF areas in the Brazilian Amazon. We surveyed a chronosequence of 42 SF plots (20 ha) near the Tapajós National Forest in Pará state to quantifying AGB growth rates. We explored the full polarimetric data testing three regression models including non-linear (NL), multiple linear regressions models (MLR), and the semi-empirical extended water cloud model (EWCM). The results showed that the intensity of previous use has affected the structure of SF by reducing the AGB accumulation and being noticeable by several polarimetric attributes. The combination of multiple prediction variables with MLR improved the AGB estimation by 70% comparing amongst other models (R² adj. = 0.51; RMSE = 13.2 Mg ha^-1) bias = 2.1 ± 37.9 Mg ha^-1. The error propagation of the MLR model was estimated to be 15%.

The cerebellum is an encephalic region classically known for its central role in the control of movement, although recent research has revealed its involvement in other cognitive and affective tasks. Several different pathologies are known to affect this structure, causing a wide range of behavioral and gait impairments. Intriguingly, although the neurodegenerative factors affect all Purkinje cells of the cerebellum uniformly, certain neurodegeneration patterns can be distinguished, in which some Purkinje cells persist longer than other cell types. Precisely, there is a cerebellar region, lobe X, which is more resistant to different types of neurodegeneration regardless of the injury. This work will review the main models of cerebellar degeneration, with special emphasis on this region, and aims to reveal a common origin for its resistance to neuronal death.

CD15 (Lewis X/Lex) is a fucosyl (3-fucosly-N-acetyl-lactosamine) moiety found on membrane proteins of various cancer cells. These include renal cancer, prostate and bladder cancers, acute leukemias, hepatocellular carcinoma, breast cancer and melanoma. The antigen plays an espe-cially significant role in renal cell carcinoma. Its high expression serves as a good prognostic marker for patients and high hopes are related to its use in the immunotherapy of the tumor. The biological role of CD15 is the interaction with E-, L- and P-selectins (adhesion molecules) and al-lowing for the adhesion with the endothelial cells. In this way, cancer cells start to interact with the endothelium of blood vessels and consequently move out from the blood flow to the sur-rounding tissues. The blockage of antigen’s function results in reduced metastatic potential. Moreover, the molecule may be a therapeutic target against cancer in monoclonal antibod-ies-based therapies. CD15s is a sialyl derivative of CD15, that possess its own unique characteris-tics. Unlike high expression of CD15, which is a prognostic factor in Hodgkin lymphoma, CD15s relate to poor prognosis for the patients. Due to the high abundance in cancer cells, CD15 is con-sidered as a marker of Cancer Stem Cells. This review presents a comprehensive description of the role of CD15 and CD15s in cancer development and metastasis and overviews the clinical appli-cations of the anti-CD15 therapy.

The stellar winds of the central stars of planetary nebulae play an essential role in planetary nebulae shaping. In the interacting stellar winds model, the fast stellar wind injects energy and momentum which are transfered to the nebular envelope through an X-ray-emitting hot bubble. Together with other physical processes, such as the ionization of the nebular envelope, the asymmetrical mass-loss in the AGB, and the action of collimated outflows and magnetic fields, the presurized hot gas determines the expansion and evolution of planetary nebulae. \emph{Chandra} and \emph{XMM-Newton} have provided us with detailed information of this hot gas. Here in this talk I will review our current understanding of the effects of the fast stellar wind in the shaping and evolution of planetary nebulae and give some hints of the promissing future of this research.

Tungsten oxides play a pivotal role in a variety of modern technologies e.g., switchable glasses, wastewater treatment, and modern gas sensors. Metallic tungsten is used as armor material, for e.g., gas turbines as well as future fusion power devices. In the first case, oxides are desired as functional materials, while in the second case, oxides can lead to catastrophic failures, so avoiding the oxidation of tungsten is desired. In both cases, it is crucial to understand the reactivity of tungsten oxides with other chemicals. In this study, the different reactivities of tungsten oxides with the highly-oxophilic beryllium are studied and compared. Tungsten-(IV)-oxide and tungsten-(VI)-oxide layers are prepared on a tungsten substrate. In the next step, a thin film of beryllium is evaporated on the samples. In consecutive steps, the sample is heated in steps of 100 K from r. t. to 1273 K. The chemical composition is investigated after each experimental step by high-resolution X-ray photoelectron spectroscopy (XPS) of all involved core levels as well as the valence band. A model is developed to analyze the chemical reactions after each step. In this study, we find that tungsten trioxide was already reduced by beryllium at r. t. and started to react to form the ternary compounds BeWO₃ and BeWO₄ at temperatures starting from 673 K. However, tungsten dioxide is resistant to reduction at temperatures of up to 1173 K. In conclusion, we find WO₂ to be much more chemically resistant to the reduction agent Be than WO₃.

Nuclear receptors (NRs) constitute a superfamily of ligand-activated transcription factors with a paramount role in ubiquitous physiological functions such as metabolism, growth, and reproduction. Owing to their physiological role and druggability, NRs are deemed attractive and valid targets for medicinal chemists. Pentacyclic triterpenes (PTs) represent one of the most important phytochemical classes present in higher plants, where oleanolic acid (OA) is the most studied PTs representative owing to its multitude of biological activities against cancer, inflammation, diabetes, and liver injury. PTs possess a lipophilic skeleton that imitates the NRs endogenous ligands. Herein, we report a literature overview on the modulation of metabolic NRs by OA and its semi-synthetic derivatives, highlighting their health benefits and potential therapeutic applications. Indeed, OA exhibited varying pharmacological effects on FXR, PPAR, LXR, RXR, PXR, and ROR in a tissue-specific manner. Owing to those NRs modulation, OA exhibited prominent hepatoprotective properties comparable to ursodeoxycholic acid (UDCA) in a bile duct ligation mice model and antiatherosclerosis effect as simvastatin in a model of New Zealand white (NZW) rabbits. It also demonstrated a great promise in alleviating non-alcoholic steatohepatitis (NASH) and liver fibrosis, attenuated alpha-naphthol isothiocyanate (ANIT)-induced cholestatic liver injury, and controlled blood glucose levels, making it a key player in the therapy of metabolic diseases. We also compiled OA semi-synthetic derivatives and explored their synthetic pathways and pharmacological effects on NRs, showcasing their structure-activity relationship (SAR). To the best of our knowledge, this is the first review article to highlight OA activity in terms of NRs modulation.

This study applied multiple scientific approaches to establish the significance of an old work of art, Red Guitar, by examining its historical origin and the color materials used in its creation. Furthremore, the study provides thus far unknown pieces of Olga Picasso's family history to be added to her biography. Scientific approaches included digital X-ray radiography, X-ray fluorescence spectroscopy, infrared Fourier transform spectroscopy, Raman spectroscopy, and elemental thermal conductivity analysis. This combination of techniques provided broad confirmation about the time when the painting was created. The work includes colors (white, black, blue, yellow, green, red, and brown/red) and prevalent use of lead-and iron-based historic pigments Chrome Yellow, Yellow Ochre and Red Ochre. It also documents the use of unconventional materials, the colorant Pigment red 4 and nitrocellulose. This investigation led to the conclusion that the art, Red Guitar, is genuine and in accord with Picasso’s work during the first two decades of the 20th century.

Background: Amyloid beta peptides (Aβ) have been identified as the main pathogenic agents in Alzheimer’s disease (AD). Soluble Aβ oligomers, rather than monomer or insoluble amyloid fibrils, show membrane-binding capacity to red blood cells (RBCs) and trigger several morphological and functional alterations in RBCs that can result in impaired oxygen transport and delivery. Since bioactive lipids have been recently proposed as potent protective agents against Aβ toxicity, we investigated the role of sphingosine-1-phosphate (S1P) in signaling pathways involved in the mechanism underlying ATP release in Aβ-treated RBCs. Methods: In RBCs following different treatments, ATP, 2,3 DPG, cAMP levels, and caspase 3 activity were determined by spectrophotometric and immunoassay. Results: S1P rescued the inhibition of ATP release from RBCs triggered by Aβ through a mechanism involving caspase-3 and restoring 2,3 DPG and cAMP levels within the cell. Conclusions: These findings reveal the molecular basis of S1P protection against Aβ in RBCs and suggest new therapeutic avenues in AD.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

In the autonomous navigation of mobile robots, precise positioning is crucial. In forest environments with weak satellite signals or in sites disturbed by complex environments, satellite positioning accuracy has difficulty in meeting the requirements of autonomous navigation positioning accuracy for robots. This article proposes a binocular vision SLAM/UWB tightly coupled localization method. The core of this algorithm is based on an Extended Kalman Filter (EKF), which utilizes the displacement increment output by binocular vision ORB-SLAM and the positioning coordinates calculated via UWB positioning as measurement information to achieve data fusion. The research utilized the constructed experimental platform to collect images and UWB ranging data in outdoor environments and experimentally validated the combined positioning method. The experimental results show that this algorithm outperforms the use of the individual UWB or visual SLAM localization methods in terms of positioning accuracy. Compared with traditional single positioning algorithms, this algorithm exhibits better practicality and stability, and can effectively suppress the impact of UWB non line of sight errors. The average error under normal line of sight conditions is 0.058 m, the root mean square error (RMSE) is 0.080, and the average error under non-line-of-sight conditions is 0.081 m, with an RMSE of 0.084. There is no significant jump or drift. Through the tightly coupled processing of binocular vision SLAM and UWB positioning, more reliable and accurate mobile robot positioning can be achieved, providing a useful reference for the autonomous navigation of mobile robots in complex environments.

DEXTER (Detection of EXplosives and firearms to counter TERrorism) is a project funded by NATO’s Science for Peace and Security (SPS) program with the goal of developing an integrated system capable of remotely and accurately detecting explosives and firearms in public places without impeding the flow of pedestrians. The active microwave component of the DEXTER project is referred to as MIC (Microwave Imaging Curtain), supported by the French SGDSN (General Secretariat of Defense and National Security), and utilizes a radar system capable of generating 3D images in real time to address non-checkpoint detection of explosives and fire-arms. The project, led by the ONERA (France), is based on a radar imaging system developed by the Fraunhofer FHR institute, using a MIMO architecture with an Ultra Wide-Band waveform. Although high-resolution 3D microwave imaging is already being used in expensive body scanners to detect firearms concealed under clothing, MIC's innovative approach lies in utilizing a high-resolution 3D imaging device that can detect larger dangerous objects carried by moving individuals at a longer range, in addition to providing discrete detection in pedestrian flow. Automatic detection and classification of these dangerous objects is carried out on 3D radar im-ages using a deep-learning network. This paper will outline the project's objectives and constraints, as well as the design, architecture, and performance of the final system. Additionally, it will present real-time imaging results ob-tained during a live demonstration in a relevant environment.

The magnetic properties of RCo3B2 compounds, with heavy rare earths, are investigated by using magnetic measurements and electronic structure calculations. The cobalt sublattice magnetizations are very small and antiparallel oriented to rare earths moments. Contributions of cobalt moments to the Curie constants were also shown. The cobalt magnetic behavior has been analyzed in spin fluctuations model. The presence of short-range order above the Curie temperatures in RCo3B2 compounds with R=Tb, Dy, and Ho has been attributed to reminiscent R5d-Co3d interactions.

The aim of this paper is to optimize thickness variation function of simply supported and cantilever beams, in terms of maximizing gaps between chosen neighboring frequencies and analyze obtained results. The optimization results are examined in terms of achieving the objective function (related to eigenproblem), but also in terms of their dynamics stiffness (forced vibrations excited by point harmonic load). In the optimization process, a Genetic Algorithm was used. Problems related to structural dynamics were solved by FEM implementation into the algorithm. Sample results were presented, and the developed algorithm was analyzed in terms of result convergence by examining several variable parameters. The authors demonstrated the validity of applying the described optimization tool to the presented problems. Conclusions were drawn regarding the correlation between stiffness and mass distribution in the optimized beams and the natural frequency modes in terms of which they were optimized.

In order to solve the interference of narrowband in the ultra-wideband (UWB) system, a high isolation of multiple-input multiple-output (MIMO) antenna is investigated in this paper. The MIMO antenna consists of 2 or 4 UWB elements; and each UWB antenna element is a monopole reconstructed with 2-notched slots, a U-shaped and inverted U-shaped slots etched on the monopole patch to achieve notch characteristics in WIMAX and ITU bands. The property of a 2-element MIMO antenna is analyzed firstly, which is put into a same substrate in parallel. Two rectangular branches are located in the middle to reduce the coupling. Then a 4-element MIMO antenna is studied to meet big size space and more application scenarios. Each element is placed orthogonally on the same substrate; and the isolation is implemented by a cross-shaped branch located in the middle of elements. Both MIMO antenna samples have been tested to verify the design. Measured results show that the working bandwidth is 2.45-14.88 GHz and 2.14-14.95 GHz, the isolation is greater than 17 dB and 20 dB, the peak gain is 5.7 dB and 5.9 dB, the max-imum radiation efficiency can reach 96% and 95%, the envelope correlation coefficient is less than 0.02 and 0.05 for the 2- and 4-element UWB MIMO antenna, respectively. They both are with very good omnidirectional characteristic with notched bands such as the WIMAX and ITU, and meet the requirements of the UWB application in most cases.

High purity TiO2 and CuO powders were synthesized by the Pechini method, an inexpensive and easy-to-implement procedure to synthetize metal oxides. The variables of synthesis were the ethylene glycol:citric acid molar ratio and the pH. High reproducibility of the anatase and tenorite phase was obtained for all synthesis routes. The degree of purity of the powders was confirmed by XRD, FTIR, UV-vis absorption and XPS spectra. SEM and TEM images revealed the powders are composed by micrometer grains that can have a spherical shape (only in the TiO2) or formed by a non-compacted nanocrystalline conglomerate. FTIR spectra only vibrational modes associated to the TiO2 or CuO with a nanoparticle behavior. UV-vis absorption spectra revealed the values of maximum absorbance percentage of both systems are reached in the ultraviolet region, with percentages above 83 % throughout the entire visible light spectrum for the CuO system, a relevant result for solar cell applications. Finally, XPS experiments allow the observation of the valence bands and the calculation of the energy bands of all oxides.

The electronic structure and some of its derived properties of Li2CaGeO4 compound have been investigated. The calculations have been performed using the full-potential linearized augmented plane wave plus local orbitals method and ultra-soft pseudo-potentials . The optimized lattice parameters are found to be ingood accord with experiment. Features such as bulk modulus and its pressure derivative, electronic band structure and density of states are reported. The elastic anisotropy of the crystal is discussed and visualized. Moreover, the optical properties reveal that Li2CaGeO4 compound are suitable candidates for optoelectronic devices in the visible and ultraviolet (UV) regions.

Thin films (100-400 nm) of Ba_xSr_1-xTiO₃ (0≤x≤1) deposited in RF-magnetron co-sputtering equipment are presented in this research work. The change of deposition rate, gap energy, and resistivity as a function of temperature- applied power change in the growth parameters was studied through the ISO colour-code lines constructed with MATLAB: By analysing the trend information and take into account the influence of the calculated "x" parameter with the Boltzmann profile fitting is proposed a method to allow a controlled set up of the RF-magnetron co-sputtering system and predict the E_g and resistivity values in the Ba_xSr_1-xTiO₃ solid solution with 0≤x≤1 for amorphous and crystalline phases. Also, a versatile tool to optimise the deposition process and material properties.

The following system of equations {x_1 \cdot x_1=x_2, x_2 \cdot x_2=x_3, 2^{2^{x_1}}=x_3, x_4 \cdot x_5=x_2, x_6 \cdot x_7=x_2} has exactly one solution in ({\mathbb N}\{0,1})^7, namely (2,4,16,2,2,2,2). Hypothesis 1 states that if a system of equations S \subseteq {x_i \cdot x_j=x_k: i,j,k \in {1,...,7}} \cup {2^{2^{x_j}}=x_k: j,k \in {1,...,7}} has at most five equations and at most finitely many solutions in ({\mathbb N}\{0,1})^7, then each such solution (x_1,...,x_7) satisfies x_1,...,x_7 \leq 16. Hypothesis 1 implies that there are infinitely many composite numbers of the form 2^{2^{n}}+1. Hypotheses 2 and 3 are of similar kind. Hypothesis 2 implies that if the equation x!+1=y^2 has at most finitely many solutions in positive integers x and y, then each such solution (x,y) belongs to the set {(4,5),(5,11),(7,71)}. Hypothesis 3 implies that if the equation x(x+1)=y! has at most finitely many solutions in positive integers x and y, then each such solution (x,y) belongs to the set {(1,2),(2,3)}. We describe semi-algorithms sem_j (j=1,2,3) that never terminate. For every j \in {1,2,3}, if Hypothesis j is true, then sem_j endlessly prints consecutive positive integers starting from 1. For every j \in {1,2,3}, if Hypothesis j is false, then sem_j prints a finite number (including zero) of consecutive positive integers starting from 1.

In (Semigroup Forum 77: 325-338, 2008) Mahmoudi M. and Renshaw J. solved a study that covers of cyclic $S$-acts over monoids. This article is an attempt to initiate the covers of finitely generated $S$-acts. We give a necessary and sufficient condition for a monoid to have the properties that $n$-generated $S$-acts have strongly flat covers, Condition $(P)$ covers and projective covers. The main conclusions extend some known results. We show also that Condition $(P)$ covers of finitely generated $S$-acts are not unique, unlike the situation for strongly flat covers. Additionally, we demonstrate that the property of Enochs' $\mathcal{X}$-precover of $S$-act $A$, where $\mathcal{X}$ denotes a class of $S$-acts that are closed under isomorphisms.

Rett Syndrome (RTT) is a severe neurodevelopmental disorder predominately diagnosed in females and primarily caused by pathogenic variants in the X-linked gene Methyl-CpG Binding Protein 2 (MECP2). Most often, the disease causing MECP2 allele resides on the paternal X chromosome while a healthy copy is maintained on the maternal X chromosome with inactivation (XCI) resulting in mosaic expression of one allele in each cell. Preferential inactivation of the paternal X chromosome is theorized to result in reduced disease severity; however, establishing such a correlation is complicated by known MECP2 genotype effects and an age dependent increase in severity. To mitigate these confounding factors, we developed an age- and genotype-normalized measure of RTT severity by modeling longitudinal data collected in the US Rett Syndrome Natural History Study. This model accurately reflected individual increase in severity with age and preserved group-level genotype specific differences in severity allowing for the creation of a normalized clinical severity score. Applying this normalized score to a RTT XCI dataset revealed that XCI influence on disease severity depends on MECP2 genotype with a correlation between XCI and severity observed only in individuals with MECP2 variants associated with increased clinical severity. This normalized measure of RTT severity provides the opportunity for future discovery of additional factors contributing to disease severity that may be masked by age and genotype effects.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

Agricultural crops productivity is heavily influenced by the strength of their seeds. Current methods for testing seed vigor, such as the germination rate and tetrazolium test, rely on time-consuming human visual inspections. Computer Vision, a crucial technology in smart production processes, offers an automated alternative and is increasingly applied in digital agriculture processes. Here we propose a method that combines YOLOv8 and morphological analysis of seeds using X-ray images to aid seed quality analysts in classifying seed lots based on their physiological potential. We examined the internal morphology of three seed lots and generated X-ray images to train a YOLOv8-based model with a post-segmentation module. This model assessed various parameters such as the total seed area, area filled by the embryo and endosperm, length, width, and calculated the percentage occupied by the embryo and endosperm in relation to the total seed area. Subsequently, seeds were classified into four categories based on the internal area occupied by the endosperm and embryo. Our findings reveal the robust performance of the YOLOv8 model in segmenting and classifying despite the challenges posed by a relatively small dataset. Notably, the proposed model achieved an impressive accuracy of up to 95.6% in identifying and segmenting the endosperm over 1,500 epochs with just 15 training images. The endosperm/seed area ratio, particularly within the 50-60% range covering over 50% of the samples, emerged as a significant metric for evaluating the viability of seed batches.

Bottlebrush (BB) elastomers with water-soluble side chains and tissue-mimetic mechanical properties are promising for biomedical applications like tissue implants and drug depots. This work investigates the microstructure and phase transitions of BB elastomers with crystallizable polyethylene oxide (PEO) side chains by real-time synchrotron X-ray scattering. In the melt, the elastomers exhibit the characteristic BB peak corresponding to the backbone-to-backbone correlation. Upon crystallization of the side chains, the intensity of the peak decays linearly with crystallinity, and eventually vanishes due to BB packing disordering within intercrystalline amorphous gaps. This behavior of the bottlebrush peak differs from an earlier study of BBs with poly(ε-caprolactone) side chains, explained by stronger backbone confinement in the case of PEO, a high-crystallinity polymer. Microstructural models based on 1D SAXS correlation function analysis suggest crystalline lamellae of PEO side chains separated by amorphous gaps of monolayer-like BB backbones.

In this work we developed two new polyfunctional hybrid systems, in which the presence of Fc redox "antennas" on peptide scaffolds allows a modulation of their electronic properties. Specifically, we synthesized two helical hexapeptides containing four Aib (α-amionoisobutyric acid) and two L-Dap (2,3-diamino propionic acid) residues. L-Dap side chains were then functionalized with Fc moieties. The structures of the two 310 helical peptides, namely Z-Aib-L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr and Z-Aib-L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr, were investigated by X-ray diffraction, 2D-NMR, CD and IR spectroscopies. Due to the helical conformation, in Z-Aib-L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr the Fc groups are located on the same face of the helix, in Z-Aib-L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr on opposite faces. Surprisingly, two bands were found in DPV for Z-Aib- L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr, indicating electrostatic interaction between the Fc groups despite their longer reciprocal distance with respect to that in Z-Aib- L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr. CD experiments at different concentrations evidenced aggregation for Z-Aib- L-Dap(Fc)-Aib-L-Dap(Fc)-Aib-Aib-NH-iPr even at high dilution, thus suggesting that the Fc-Fc electrostatic interaction could be of intermolecular nature.

Background: Erythropoietic protoporphyria (EPP) and X-linked protoporphyria (XLP) are the two most common subtypes within rare genetic photodermatoses, which can lead to incapacitating pain episodes. Methods: We reviewed previous and current treatment options for EPP/XLP, notably with a focus on metabolism, pharmacokinetics, mechanism of action, key clinical trial results, and limitations of Dersimelagon [MT-7117]. Results: In review of treatment modalities for EPP/XLP, Dersimelagon has demonstrated an acceptable safety profile with the ease of once-daily oral dosage. Conclusions: Dersimelagon should be a considered as a potential treatment for EPP/XLP. Ongoing studies will provide additional insights into expanding the treatment options for those suffering from EPP/XLP.

The archival Rossi X-ray Timing Explorer (RXTE) Proportional Counter Array (PCA) observations of HZ Her/Her X-1 are analyzed here. The time periods for Anomalous Low States are refined. The 35-day X-ray lightcurve of Her X-1 is produced using 35-day phases determined with RXTE All-Sky Monitor (ASM) and Swift Burst Altert Telescope (BAT) data, with adjustments based on the RXTE/PCA data. The result is the highest sensitivity 35-day lightcurve of Her X-1. The RXTE/PCA data were separated into 8 differents states of the 35-day cycle: Main High (MH) turn-on, MH, MH decline, Low State (LS) 1, Short High (SH) turn-on, SH, SH decline, and LS2. Orbital lightcurves were created for each state, and the different states are compared. Eclipse data was extracted for each state to determine the changes of eclipse shape with 35-day phase. A scattering corona model was fit to the eclipses for the different 35-day states: this shows that the corona is present at all 35-day phases with similar intensity. We carried out a search for previously-reported dips with no absorption, but did not find any.

Purpose: We assessed if a CXR AI algorithm can detect missed or mislabeled chest radiographs (CXRs) findings in radiology reports. Methods: We queried multi-institutional radiology reports search database of 13-million reports to identify all CXRs reports with addendums from 1999-2021. Of the 3469 CXR reports with an addendum, a thoracic radiologist excluded reports where addendum was created for typographic errors, wrong report template, missing sections, or uninterpreted signoffs. The remaining reports with addendum (279 patients) with errors related to side-discrepancy or missed findings such as pulmonary nodules, consolidation, pleural effusions, pneumothorax, and rib fractures. All CXRs were processed with an AI algorithm. Descriptive statistics were performed to determine the sensitivity, specificity, and accuracy of AI to detect missed or mislabeled findings. Results: AI had high sensitivity (96%), specificity (100%), and accuracy (96%) for detecting all missed and mislabeled CXR findings. The corresponding finding-specific statistics for AI were nodules (96%, 100%, 96%), pneumothorax (84%, 100%, 85%), pleural effusion (100%, 17%, 67%), consolidation (98%, 100%, 98%), and rib fractures (87%, 100%, 94%). Conclusion: The CXR AI could accurately detect mislabeled and missed findings. Clinical Relevance: The CXR AI can reduce the frequency of errors in detection and side-labeling of radiographic findings.

The TanDEM-X mission is acquiring a new dataset to provide a temporally independent DEM, called "TanDEM-X Change DEM". This set of acquisitions taken between 2017 and 2020 has a clear temporal separation to the TanDEM-X global DEM data which were acquired between 2010 and 2015. Therefore, this new DEM aims to enable the characterization of terrain changes. Improvements in the acquisition planning and the data processing were necessary to generate this Change DEM with fewer acquisitions but still very high accuracy. For this, the use of an edited TanDEM-X DEM as a "starting point" for the interferometric processing is mandatory.

Astronomical X-ray polarimetry was first explored in the end of the 60's by pioneering rocket instruments. The craze arising from the first discoveries on stellar and supernova remnant X-ray polarization led to the addition of X-ray polarimeters on-board of early satellites. Unfortunately, the inadequacy of the diffraction and scattering technologies required to measure polarization with respect to the constraints driven by X-ray mirrors and detectors, coupled to long integration times, slowed down the field for almost 40 years. Thanks to the development of new, highly sensitive, compact X-ray polarimeters in the beginning of the 2000's, the possibility to observe astronomical X-ray polarization is rising again and scientists are now ready to explore the high energy sky thanks to modern X-ray polarimeters. In the forthcoming years, several X-ray missions (both rockets, balloons and satellites) will open a new observational windows. A wind of renewal blows over the area of X-ray polarimetry and this paper presents for the first time a quantitative assessment, all based on scientific literature, of the growth of interest for astronomical X-ray polarimetry.

The aging mechanism of 10% and 30% nickel substituted manganese hexacyanoferrate cathode material in aqueous zinc-ion batteries has been explored through the advanced synchrotron-based two-dimensional x-ray fluorescence technique. Thanks to the two-dimension modality, not only the metal concentration dynamics throughout the entire electrodes was followed during the aging process, but their spatial distribution was also revealed, suggesting the route of the material transformation. The dissolution of Mn and Ni, and the penetration of Zn inside the framework, alongside the Mn aggregations outside the hexacyanoferrate framework were detected. Additionally, the possibility of conducting x-ray absorption spectroscopy measurements on the regions of interest made it possible to explore the chemical state of each metal, and furthermore, synchrotron-based powder x-ray diffraction demonstrated the gradual structural modification in 30% Ni-containing sample series, in terms of the different phase formation.

The flux growth of InVO4 bulk single crystals has been explored for the first time. The reported eutectic composition at a ratio of V2O5:InVO4 = 1:1 could not be used as a self-flux, since no sign of melting was observed up to 1100 °C. Crystals of InVO4 of typical size 0.5×1×7 mm3 were obtained using copper pyrovanadate (Cu2V2O7) as a flux, using Pt crucibles. XRD confirmed the orthorhombic Cmcm structure. Rests of flux material were observed on the sample surface, with occasional traces of Pt indicating some level of reaction with the crucible. X-ray absorption spectroscopy showed that oxidation states of indium and vanadium ions are +3 and +5, respectively. The size and high quality of the obtained InVO4 crystals makes them excellent candidates for the further study of their physical properties.

The increasing use of energy resources recovered from the subsurface environments and the resulting carbon imbalance in the environment has motivated the need to develop thermodynamically downhill pathways to convert and store CO₂ as water insoluble calcium or magnesium carbonates. While previous studies extensively explored aqueous routes to produce calcium and magnesium carbonates from CO₂, there has been a limited scientific understanding of the phase evolution and textural changes during the direct gas-solid conversion routes to produce calcium carbonate from calcium hydroxide, which is one of the abundant constituents of alkaline industrial residues. With increasing interest in developing integrated pathways for capturing, converting and storing CO₂ from dilute flue gases, understanding the compositions of the product phases as they evolve is essential for evaluating the efficacy of a given processing route. Therefore, in this study, we investigate the phase evolution and the corresponding textural changes as calcium hydroxide is converted to calcium carbonate under the continuous flow of CO₂ at an ambient pressure of 1 atm and on heating continuously from 30 °C to 500 °C using in-operando wide angle X-ray scattering (WAXS), small angle X-ray scattering (SAXS), and ultra-small angle X-ray scattering (USAXS) measurements.

The surprisingly high catalytic activity of gold has been known to the heterogeneous catalysis community since the mid-1980s. Significant effort has been directed towards improving the reactivity of these surfaces towards important industrial reactions. One such strategy is the introduction of small amounts of other metals to create Au-based surface alloys. In this work, we investigate the synergistic effect of Pt doping of the Au(111) surface towards decreasing the activation barrier of the methanol dehydrogenation elementary step, within first-principles density functional theory. To this aim we construct several models of \ce{Pt}-doped Au(111) surfaces, including a full \ce{Pt} overlayer and monolayer. The effect of \ce{Pt} surface doping is then investigated via the computation of adsorption energies of the various chemical species involved in the catalytic step, and the estimation of activation barriers of methanol dehydrogenation. Both electronic and strain effects induced by \ce{Pt} surface doping concur in substantially lowering the activation energy barrier of this important reaction elementary step. Morever, in the presence of preadsorbed atomic oxygen, \ce{Pt} surface doping can be used to reduce the activation energy for methanol dehydrogenation to as low as 0.1 eV.

We investigate a single-particle density of states in the three-dimensional system described by effective two-band Hamiltonian which describes a ground state in two distant electronic phases: the semimetalic nodal-loop phase and the insulating gapped phase. Analysis of valence bands and Fermi surfaces in both phases indicates that the density of states crucially depends on the parameter in the Hamiltonian of the system that controls a topological alternation of the Fermi surface. The signature of that alternation is expected to play an important role in all quantities closely related to the density of electronic states, such as charge transport and optical conductivity of the system for example.

The conformational preferences of the ester group have the potential to facilitate the large amplitude folding of long alkyl chains in the gas phase. They are monitored by Raman spectroscopy in supersonic jet expansions for the model system methyl butanoate, after establishing a quantitative relationship to quantum-chemical predictions for methyl methanoate. This requires a careful analysis of experimental details, and a simulation of the rovibrational contours for near-symmetric top molecules. The technique is shown to be complementary to microwave spectroscopy in quantifying coexisting conformations. It confirms that a C-O-C(=O)-C-C chain segment can be collapsed into a single all-trans conformation by collisional cooling, whereas alkyl chain isomerism beyond this five-membered chain largely survives the jet expansion. This sets the stage for the investigation of linear alkyl alkanoates in terms of dispersion-induced stretched-chain to hairpin transitions by Raman spectroscopy.

This paper presents two designs of high-efficiency polarizer reflectarray antennas able to generate a collimated beam in dual-circular polarization using a linearly polarized feed, with application to high-gain antennas for data transmission links from a Cubesat. First, an 18 cm x 18 cm polarizer reflectarray operating in the 17.2 - 22.7 GHz band has been designed, fabricated and tested. The measurements of the prototype show an aperture efficiency of 52.7% for right-handed circular polarization (RHCP) and 57.3% for left-handed circular polarization (LHCP), both values higher than those previously reported in related works. Then, a dual-band polarizer reflectarray is presented for the first time, which operates in dual-CP in the frequency bands of 20 and 30 GHz. The proposed antenna technology enables a reduction of the complexity and cost of the feed chain to operate in dual-CP, as a linear-to-circular polarizer is no longer required. This property, combined with the lightweight, flat profile and low fabrication cost of printed reflectarrays, makes the proposed antennas good candidates for Cubesat applications.

In this paper a perspective on the application of spatially- and Angle- Resolved PhotoEmission Spectroscopy (ARPES) for the study of two-dimensional (2D) materials is presented. ARPES allows the direct measurement of the electronic band structure of materials generating extremely useful insights into their electronic properties. The possibility to apply this technique to 2D materials is of paramount importance because these ultrathin layers are considered fundamental for future electronic, photonic and spintronic devices. In this review an overview of the technical aspects of spatially localized ARPES is given along with a description of the most advanced setups for laboratory and synchrotron-based equipment. This technique is sensitive to the lateral dimensions of the sample, therefore a discussion on the preparation methods of 2D material is presented. Some of the most interesting results obtained by ARPES are reported in three sections including: graphene, transition metal dichalcogenides (TMDCs) and 2D heterostructures. Graphene has played a key role in ARPES studies because it inspired the use of this technique with other 2D materials. TMDCs are presented for their peculiar transport, optical and spin properties. Finally, the section featuring heterostructures highlights a future direction for research into 2D material structures.

The development of novel coherent and brilliant sources, such as soft X-ray Free Electron Laser (FEL) and High Harmonic Generation (HHG) enables new ultrafast analysis of the electronic and structural dynamics of a wide variety of materials. Soft X-ray FEL delivers high brilliance beams with short pulse duration, high spatial coherence and photon energy tunability. In com-parison with FELs, HHG X-ray sources are characterized by a wide spectral bandwidth and few to sub-femtosecond pulses. The approach will lead to time-resolved reconstruction of molecular dynamics, shedding light on different photochemical pathways. The high peak brilliance of soft X-ray FELs facilitates investigations in nonlinear regime, while the broader spectral bandwidth of the HHG sources may provide the simultaneous probing of multiple components. Significant technical breakthroughs in these novel sources are under way to improve brilliance, pulse dura-tion, and to control spectral bandwidth, spot size, and energy resolution. Therefore, in the next few years, the new generation of soft X-ray sources combined with novel experimental tech-niques, new detectors, and computing capabilities will allow the study of several extremely-fast dynamics, such as vibronic dynamics. In the present review, we shortly discuss recent devel-opments in experiments, performed with soft X-ray FELs and HHG sources, operating near car-bon K-absorption edge, being a key atomic component in biosystems and soft materials. Differ-ent spectroscopy methods such as time-resolved pump-probe techniques, nonlinear spectrosco-pies and photoelectron spectroscopy studies have been addressed in an attempt of a better un-derstanding of fundamental physico-chemical processes

This paper serves as a seamless continuation of the previous work titled "Special Spirals are Produced by the ROTASE Galactic Spiral Equations with the Sequential Prime Numbers." Upon revisiting the data, a noteworthy observation emerged: the special spirals can be meticulously aligned with the prime spiral on a point-by-point basis through careful scaling and rotation for the parameter ρ remaining a constant greater than one. As ρ increases, both the scaling factor and rotation angle exhibit a corresponding augmentation, albeit with an intriguing caveat—the rotation angle asymptotically approaches its limit of 90°. Notably, the galactic spiral can be perceived as a remarkably close approximation of the Archimedean spiral, with the degree of proximity increasing as ρ grows larger. Furthermore, an intriguing correspondence arises when ρ takes on a value of 1; at this value, the galactic spiral bears a striking resemblance to the Fermat spiral, the space between two consecutive spiral loops undergoes a continuous reduction as the loop's radius expands, yet it never diminishes to zero; simultaneously, the area between two successive loops experiences an augmentation with the value of ρ.

Diastematomyelia, also known as split cord syndrome, is a congenital disorder of the spinal cord. As the name suggests, the spinal cord is split into two resulting in neurological complaints associated with cutaneous symptoms. Although the diagnosis can be done clinically, for disease confirmation, various radiological investigations are used for the diagnosis of this condition. Here, we present a case of a 54-year-old Indian female diagnosed with diastematomyelia. The clinical features, diagnostic modalities, treatment options and prognosis of this condition have been discussed.