With the proportional reduction of MOSFET size, the leakage-to-barrier reduction (DIBL) effect leads to a more significant increase in the tunneling current on the gate, and the appearance of the gate tunneling current also seriously affects the static characteristics of the device. In this paper, a new theoretical model of the relationship between the direct tunneling current and the thickness of the oxide layer under the DIBL effect is proposed for the MOSFET device with ultra-thin oxide layer. On this basis, the characteristics of the MOSFET device are studied in detail by using HSPICE, and their working conditions are quantitatively analyzed. The characteristic variation trend of small-size devices under the influence of gate tunneling current is predicted. The simulation results using BSIM4 model are consistent with the theoretical model. The theory and data in this paper will provide useful reference for large scale integrated circuit design.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

Tantalum oxide thin films are deposited by DC reactive magnetron sputtering from a tantalum metallic target and oxygen as reactive gas. The reactive gas pulsing process (RGPP) is implemented to produce TaOx compounds with tunable chemical compositions. The argon mass flow rate is maintained constant whereas that of the oxygen gas is pulsed during the deposition. A constant pulsing period T = 10 s is used and the introduction time of the oxygen gas, namely the tON injection time, is systematically changed from 0 to 100 % of the pulsing period T. As the tON injection time increases, the chemical composition of as-deposited TaOx films is continuously changed from pure metallic tantalum to the over-stoichiometric Ta2O5 material. Analysis of the crystallographic structure by X-ray diffraction shows that the films adopt the body-centered cubic structure (metallic Ta) for the lowest tON injection time values (oxygen stoichiometry x < 1.0) and become amorphous for the longest tON injection times. It is shown that the tON injection time is a key parameter to produce either homogeneous tantalum oxides, or periodic Ta/TaOx multilayers with alternations close to 3 nm. Similarly, optical transmittance spectra of the film/glass substrate system are recorded in the visible region and the electrical conductivity of the films is measured vs. temperature. Both exhibit a gradual evolution from metallic (300K = 8.17105 S m-1 with a null optical transmittance in the visible range) to semi-conducting (300K = 1.97103 S m-1 with a semi-transparent behavior) and finally to dielectric properties (300K < 10-5 S m-1 for interferential films) as a function of the oxygen concentration in the films.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

ZnO films with Ti atoms incorporated (TZO) in a wide range (0-18 at. %) have been grown by reactive co-sputtering on silicon and glass substrates. The influence of the titanium incorporation in the ZnO matrix on the structural and optical characteristics of the samples has been determined by Rutherford backscattering spectroscopy (RBS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results indicate that the samples with low Ti content (< 4 at. %) exhibit the wurtzite-like structure, with the Ti+4 ions substitutionally incorporated into the ZnO structure, forming Ti-doped ZnO films. In particular, very low concentration of Ti (<0.9 at. %) leads to a significant increase of the crystallinity of the TZO samples. Higher Ti contents give rise to a progressive amorphization of the wurtzite-like structure so samples with high Ti content (≥18at. %), displays an amorphous structure indicating the XPS analysis a predominance of Ti-O-Zn mixed oxides. The energy gap, obtained from absorption spectrophotometry, increases from 3.2 eV for pure ZnO films to 3.6 eV for those with the highest Ti content. Ti incorporation in the ZnO samples below 0.9 at. % rises both, the blue (380 nm) and green (550 nm) bands of the photoluminescence (PL) emission, thereby indicating a significant improvement of PL efficiency of the samples.

To address the severe distresses of asphalt pavement, a new type of pavement maintenance treatment, porous ultra-thin overlay (PUTO) with small particle size was proposed. The PUTO has a thickness of 1.5~2.5 cm and a large void ratio of 18~25%. As a newly asphalt mixture, the structure characteristics differ from traditional pavement. Therefore, it is necessary to investigated the fabrication schemes in laboratory and on-site, respectively. In this study, the optimal fabrication schemes, including compaction temperature and number of blows of PUTO were determined based on Cantabro test and volumetric parameters. Then, the corresponding relationship between laboratory and on-site compaction work was then established based on the energy equivalent principle. On this basis, the numbers of on-site rolling passes and the combination method were calculated. The results show that increased compaction temperature and number of blows reduce the height and enhance the compactness of the Marshall sample. With the same temperature and number of blows, the scattering resistance of coarse gradation (PAC-1) is better than that of fine gradation (PAC-2), and the increased asphalt viscosity significantly improves the scattering resistance of the asphalt mixture. To ensure the scattering resistance and volumetric characteristic, the initial compaction temperature of the PAC-1 and PAC-2 should not be lower than 150 °C and 165 °C, respectively. Then, the laboratory compaction work and on-site compaction work were calculated and converted based on the principle of energy equivalence. Consequently, the on-site compaction combination of rolling machines for four asphalt mixtures was determined. According to the volumetric parameters, the paving test section proved that the construction temperature and the on-site rolling combination determined by laboratory tests are reasonable, and ultra-thin overlay has good structural stability, drainage and skid resistance.

In this paper any superalgebra is generalized to a new form, namely ultra algebra. We study some algebraic structure results for ultra algebras and we have defined some maps on ultra algebras to know ultra derivation and Jordan ultra derivation. Moreover on certain assumptions we have proved that Jordan ultra derivation is an ultra derivation.

A cell filtration platform that affords accurate size separation and minimizes fouling was developed. The platform features an ultra-thin porous membrane (UPM) filter, a pumping head for backflushing (PHB), and cell size measurement (CSM) software. The UPM chip is an ultrathin free-standing membrane with a large window area of 0.68 mm2, a pore diameter of 5 to 9 μm, and a thickness of less than 0.9 μm. The PHB prevents filter fouling. The CSM software analyzes the size distributions of the supernatants and subnatants of isolated cells and presents the data visually. The D99 particle size of cells of the chronic myeloid leukemia (CML) line K562 decreased from 22.2 to 17.5 μm after passage through a 5-μm filter. K562 cells could be separated by careful selection of the pore size; the recovery rate attained 91.3%. The method was compared to conventional blocking models by evaluating the mean square errors (MSEs) between the measured and calculated filtering volumes. The filtering rate was fitted by a linear regression model with a significance that exceeded 0.99 based on the R2 value. The platform can be used to separate various soft biomaterials and affords excellent stability during filtration.

Slot-die coatings are advantageous when used for coating large-area flexible devices; in particular, the coating width can be controlled, and simultaneous multi-layer coatings can be processed. Till date, the effects of ink widening and coating gap on the coating thickness have only been considered in a few studies. To this end, we developed two mathematical models to accurately estimate the coating width and thickness considering these two effects. We used root mean square deviation (RMSD) to experimentally verify the developed method. The coating width was seen to increase and the coating thickness was seen to decrease when the coating gap was increased. Experimental results showed that the estimation performances of the coating width and thickness models were as high as 98.46 % and 95.8 %, respectively. We believe that the developed models can be useful for determining the coating conditions according to the ink properties to coat a functional layer with user-defined widths and thicknesses in both lab- and industrial-scale roll-to-roll slot-die coating processes.

The nitrogen-doped amorphous oxide semiconductor (AOS) thin film transistors (TFTs) with double-stacked channel layers (DSCL) were prepared and characterized. The DSCL structure composed of nitrogen-doped amorphous InGaZnO and InZnO films (a-IGZO:N/a-IZO:N or a-IZO:N/a-IGZO:N) made the corresponding TFT devices exhibit quite large field-effect mobility due to the existence of double conduction channels. Especially, the a-IZO:N/a-IGZO:N TFTs showed even better electrical performance (μ_FE = 15.0 cm²·V^-1·s^-1, SS = 0.5 V/dec, V_TH = 1.5 V, I_ON/I_OFF = 1.1×10⁸) and stability (V_TH shift of 1.5, -0.5, and -2.5 V for positive bias-stress, negative bias-stress and thermal stress tests, respectively) than the a-IGZO:N/a-IZO:N TFTs. Based on the X-ray photoemission spectroscopy measurements and energy band analysis, it was assumed that the optimized interface trap states, the less ambient gas adsorption, and the better suppression of oxygen vacancies in the a-IZO:N/a-IGZO:N hetero-structures might be responsible for the better behaviors of the corresponding TFTs.

Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO₂), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 10²⁰ cm⁻³ and 10–20 cm²/Vs, which are typical values for SnO₂ films, and show a negligible temperature dependence from room temperature down to -269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO₂ samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

The electrical and optical properties of sol-gel derived aluminum-doped0 zinc oxide thin films containing 2 at.% Al were investigated considering the modifying effects of 1) increasing the sol H₂O content; and 2) thermal treatment procedure with high-temperature approach followed by an additional heat-treatment step under a reducing atmosphere. According to the results obtained via the TG-DTA analysis, FT-IR spectroscopy, X-ray diffraction technique and four-point probe resistivity measurement, it is argued that the sol hydrolysis, decomposition of the deposited gel and crystallization of grains result in grains of larger crystallite size and stronger c-axis preferred orientation with slightly less microstrain in the modified sample. The consequent morphology and grain-boundary characteristics turn out as improved conductivity, implying higher values of concentration and mobility of charge carriers. A detailed investigation on samples optical properties, in terms of analyzing their absorption and dispersion behaviors through the UV-Vis-NIR spectroscopy, support our reasoning for the increase of the mobility, and to a lesser extent, the concentration of charge carriers, while causing only a slight degradation of optical transmission. Hence, an enhanced performance as a transparent conducting film is claimed for the modified sample by comparing the figure-of-merit values.

Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

Highly macroporous thin films of WO₃ were fabricated on transparent conductive substrates by application of a polymeric organic paste loaded with an amine/tungstate complex. After spin-coating and annealing at 550^oC, the resulting yellow films are found to be comprised of channeled array of clustered nanoparticles. These channels are confirmed by scanning electron microscopy to extend through the entire length of the coating. The high porosity of the material enables the insertion of a co-catalyst into the internal structure of the film. These internally functionalized composites demonstrate good photosensitivity and stability in neutral electrolyte.

The purpose of this study was to conduct a meta-analysis that shows the influence of fiber on ultimate compressive strength and tensile strength of ultra-high performance concrete. The internet scholarly search engines and ScienceDirect article references were used to illustrate the papers concerning the experimental investigations of mechanical properties of ultra-high strength concrete with and without fiber with clearly, completely and comparative raw data. The normal concrete test results were dismissed from this search. Seven trials were identified based on the adopted inclusion and exclusion criteria above. The meta-analysis based on standardized mean difference was carried out on the basis of a fixed-effects model for the major outcomes of the ultimate compressive and tensile properties of ultra-high performance concrete. A total of 888 test specimens were enrolled in these seven trials. The combined analysis yielded a sign of a significant improvement in ultimate compressive strength and tensile strength of ultra-high strength concrete with fiber addition of 2% by concrete volume. The summary effect size of ultimate compressive strength was 2.34 while a more improvement in term of tensile strength with effect size of 2.64. By addition fiber of 2% provides a significant benefit in mechanical properties of ultra-high performance concrete.

We demonstrated a new approach to the production of three-dimensional-coated patterns using liquid route. Metallic perovskite oxides were coated onto three-dimensional (3D) microstructured substrates with different aspect ratios. The success of the method relies on the solution viscosity monitored by adding viscous liquid. The process of oxide thin films consists in three steps: preparing the precursor solution, coating the solution by spin-coating process onto three-dimensional-Si substrates and post-annealing. The chemical solution 3D-coating is conformal.

The influence of the film thickness and the substrate’s refractive index on the surface mode at the superstrate is an important study step that may help clearing some of the misunderstandings surrounding their propagation mechanism. A single sub-wavelength slit perforating a thin metallic film is among the simplest nanostructure capable of launching Surface Plasmon Polaritons on its surrounding surface when excited by an incident field. Here, the impact of the substrate and the film thickness on surface waves is investigated. When the thickness of the film is comparable to its skin depth, SPP waves from the substrate penetrate the film and emerge from the superstrate, creating a superposition of two SPP waves, that leads to a beat interference envelope with well-defined loci which are the function of both the drive frequency and the dielectric constant of the substrate/superstrate. As the film thickness is reduced to the SPP’s penetration depth, surface waves from optically denser dielectric/metal interface would dominate, leading to volume plasmons that propagate inside the film at optical frequencies. Interference of periodic volume charge density with the incident field over the film creates charge bundles that are periodic in space and time.

More people around the world now have obesity than suffer from starvation thanks to our modern food system. Agriculture was transformed over the 20^th century by a variety of technological advancements that relied heavily on fossil fuels. In the United States of America, government policies and economic incentives led to surplus production of cheap inputs to processed food industries that produced a wide variety of heavily marketed, convenient, rewarding, timesaving, and relatively inexpensive ultra-processed foods. The energy available in the United States food supply increased much more than population needs, albeit with large inequities in food distribution and nutrition security. While most of the rise in per capita food availability during the late 20^th and early 21^st centuries in the United States resulted in increased food waste, a variety of mechanisms have been proposed by which changes in the increasingly ultra-processed food environment resulted in excess energy intake disproportionately in people genetically susceptible to obesity. As populations continue to grow, substantial investments in coordinated nutrition and agricultural research are needed to transform our current food system to one that relies less on fossil fuels, preserves biodiversity, ensures environmental health, and provides equitable access to affordable, safe, and nutritious food that reduces the prevalence of chronic diseases like obesity.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

Many applications in the context of Industry 4.0 require precise localization. However, indoor localization remains an open problem, especially in complex environments such as industrial environments. In recent years, we have seen the emergence of Ultra WideBand (UWB) localization systems. The aim of this article is to evaluate the performance of a UWB system to estimate the position of a person moving in an indoor environment. To do so, we implemented an experimental protocol to evaluate the accuracy of the UWB system both statically and dynamically. The UWB system is compared to a ground truth obtained by a motion capture system with a millimetric accuracy.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

We demonstrate a concept and fabrication of lithography-free layered metal-\ce{SiO2} thin-film structures which have reduced reflectivity (black appearance), to as low as 0.9~\%, with 4.9~\% broadband reflectance (8.9~\% for soda lime) in the 500 - 1400~nm range. The multi-layered (four layers) thin-film metamaterial is designed so that optical impedance matching produces minimal reflectance and transmittance within the visible and infra-red (IR) spectral region for a range of incident angles. The structure has enhanced absorbance and is easily tuned for reduced minimal transmission and reflection.

Regenerated silk (RS) is a protein-based “biopolymer” that enables the design of new materials; here, we called “bionic” the process of regenerated silk production by a fermentation-assisted method. Based on yeast’s fermentation, here we produced a living hybrid composite made of regenerated silk nanofibrils and a single-cell fungi, the Saccharomyces cerevisiae yeast extract, by fermentation of such microorganisms at room temperature in a dissolution bath of silkworm silk fibers. The fermentation-based processing enhances the beta-sheet content of the RS, corresponding to a reduction in water permeability and CO₂ diffusion through RS/yeast thin films enabling the fabrication of a mechanically robust film that enhances food storage durability. Finally, a transfer print method, which consists of transferring RS and RS/yeast film layers onto a self-adherent paraffin substrate, was used for the realization of heat-responsive wrinkles by exploiting the high thermal expansion of the paraffin substrate that regulates the applied strain, resulting in a switchable coating morphology from the wrinkle-free state to a wrinkled state if the food temperature overcomes a designed threshold. We envision that such efficient and smart coatings can be applied for the realization of smart packaging that, through such a temperature-sensing mechanism, can be used to control food storage conditions.

(1) Background: Ultra-endurance exercise involves a high physical impact, resulting in muscle damage, inflammatory response and production of free radicals that alter the body's oxidative state. Supplementation with antioxidants, such as beetroot, may improve recovery in ultra-endurance runners. The aim of this study was to determine whether there is a correlation between the beetroot intake and the recovery of serum oxidative status, inflammatory response and muscle damage parameters after an ultra-endurance race. (2) Methods: An observational and longitudinal study was conducted by means of surveys and blood samples collected from 32 runners during the IX Penyagolosa Trails CSP® race and the two following days. The variables C-reactive protein (CRP), lactate dehydrogenase (LDH), creatine kinase (CK), the activity of the antioxidant enzymes glutathione peroxidase (GPx) and glutathione reductase (GR), as well as the oxidative damage markers malondialdehyde (MDA), carbonyl groups (CG) and loss of muscle strength using the Squat Jump test (SJ) were analyzed to discriminate whether beetroot consumption can modulate the recovery of ultra-trail runners. (3) Results: Significant differences were observed between runners who ingested beetroot and those who did not, in terms of oxidative status, specifically in serum GPx activity at 24 and 48 hours, muscle damage variables CK and LDH and in SJ test at the finish line. Therefore, the intake of supplements containing beetroot positively influences the recovery of serum oxidative status and muscle damage after ultra-endurance running.

This article explores the implementation of high accuracy GPS denied Ad-Hoc localization. There is little research on Ad-Hock UWB-enabled localization systems with mobile and stationary nodes. This work aims to demonstrate the localization of bicycle-modeled robots in a non-static environment through a mesh network of mobile, stationary robots and ultra-wideband sensors. The non-static environment adds a layer of complexity when actors can enter and exit the node’s field of view. The method starts with an initial localization step where each unmanned ground vehicle (UGV) uses the surrounding, available anchors to derive an initial local or, if possible, global position estimate. The initial localization uses a simplified implementation of the iterative multi-iteration Ad-Hoc Localization System (AHLos). This estimate was refined using an unscented Kalman filter (UKF) following a constant turn rate and velocity magnitude model (CTRV). The UKF fuses the robot’s odometry and the range measurements from the Decawave ultra-wideband receivers stationed on the network nodes. Through this position estimation stage, the robot broadcasts to its neighbors its estimated position to help the others further improve their localization estimates and localize themselves. This wave-like cycle of nodes helping to localize each other allows the network to act as a mobile Ad-Hoc localization network.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Unhealthy diet is an important health problem in the region of the Americas, and Uruguay does not escape this reality. Nutritional problems in Uruguayan school-age children are overweight and obesity. Caloric intake is excessive for 60% of children and 28% of calories come from ultra-processed products (UPP) [CODICEN 2021] [MIDES 2020) (Köncke, Toledo, 2021). In 2018, an evaluation of food intake was conducted in a representative sample of public schools in the city of Montevideo. Food and preparations were categorized according to the NOVA system, later they were analyzed according to the Pan American Health Oganization nutrient profile model (PAHO NPM). Only 0.52% of children consumed exclusively natural foods, unprocessed, minimally processed or culinary ingredients. Twenty-five percent of children consumed ≥ 4 products categorized with excessive content of free sugars, total fat or saturated fat according to the PAHO NPM; in the case of excessive sodium this was 40%. In general, children who included products with excessive free sugars, sodium or saturated fat in their diet exceeded the limits established by PAHO and as a result their diet is of poorer nutritional quality compared to children who did not consume such products.

We report a very frugal microscope building method from easily realizable parts. We show a highly portable field ready compound type microscope with bright field, dark field and projection microscopy capabilities. It has good resolution and magnification for multiple aspects of education and diagnosis. We demonstrate that such a system can be built from simple lenses in laser pointers and camera modules with no specific 3d printed parts or costly lenses. We show all the parts of the system like stage, coarse and fine focussing system, microscope body, even slides can be built from commonly available materials like soda bottle and DVD disks. We list alternate, safer and easily available staining methods and chemicals. The microscope is developed with a target that it can be self-developed even in rural areas of the world with only resources at one’s disposal with very little education. This features a stable focussing and panning system for comfortable viewing through eyes and also easy imaging with a smartphone. We show its utility for microorganism analysis and potential for clinical diagnosis.

The analysis of particulate matter (PM) in dilute solutions is an important target for environmental, geochemical and biochemical researches. Here we show how the microdrop technology may allow to control, through the evaporation of small droplets, the deposition of insoluble materials dispersed in a solution on a well-defined area with a specific spatial pattern. Using this technology the superficial density of the deposited solute can be accurately controlled. In particular, it becomes possible to deposit an extremely reduced amount of insoluble material -in the order of few μg- on a confined area, thus allowing a relatively high superficial density to be reached within a limited time. In this work we quantitatively compare the microdrop technique for the preparation of particulate matter samples with the classical filtering technique. After having been optimized, the microdrop technique allows to obtain a more homogeneous deposition and limit sample consumption of a factor ~25. This method is potentially suitable for many novel applications in different scientific fields.

Plasma polymerized (PP) thin films deposited in a soft or intermediate plasma discharge from hexamethyldisiloxane (HMDSO) were developed as sensors for the detection of volatile organic compounds (VOCs) vapors. Energy dispersive X-ray spectroscopy (EDX) and X-ray reflectometry (XRR) were performed to determine the organosilicon films elemental composition and density. Spectroscopic ellipsometry measurements were carried out to determine the refractive index of the films. Quartz crystal microbalance (QCM) and ellipsometry coupled to vapor sorption were used to investigate the sorption mechanism of several VOCs vapors into the films as a function of the plasma deposition conditions. The density and the refractive index of the PP-HMDSO films increased with the plasma energy due to a different chemical composition and different proportion of free volumes in the material network. The PP-HMDSO films showed different affinities towards the VOCs vapors depending on the plasma discharge energy. The films elaborated in the lowest plasma energy revealed a good sensitivity towards the VOCs especially toluene (one of the BTEX vapors) compared to the other films deposited under higher plasma energy. In addition, the selectivity between toluene and other non-BTEX VOCs such as heptane and ethanol decreased to become zero while increasing the plasma energy.

Silicon-based thin-films and nanostructures are of paramount importance in a wide range of applications, including microelectronics, photovoltaics, large area sensors, as well as biomedicine. The wide accessibility of silicon and its relatively low cost have driven a continuous improvement of the technology based on this element. Plasma technology has been widely used for the synthesis of coatings and nanostructures based on silicon. Moreover, it has given a fundamental contribution for continuously improving the control of the physicochemical properties of silicon-based materials, and for allowing the synthesis of nanometric structures with well-defined shape and morphology. In this work, we have reviewed the most interesting developments of plasma-assisted processed for the synthesis of Si-based materials, both inorganic and organic, in the last five years. A special attention has been given to the new techniques, or modifications of already existing ones, that open new possibilities for the synthesis of materials with new properties, as well as nanostructures with novel characteristics.

Highly transparent thin films with the chemical formula BaSrMgWO6 were deposited by spin coating using a solution of nitrates of Ba, Sr and Mg and ammonium paratungstate in dimethylformamide with a ratio Ba:Sr:Mg;W=1:1:1:1. XRD, SEM, EDX and XPS investigations evidenced that an annealing at 800 ºC for 1h leaves the structure amorphous with a precipitate on the surface and that a supplementary annealing at 850 ºC for 45 min forms a nanocrystalline structure and dissolves a part of precipitates. It was evidenced a textured double perovskite cubic structure (61.9%) decorated with tetragonal and cubic impurity phases (12.7 %) like BaO2, SrO2 and MgO and an under-stoichiometric phase (24.4%) with the chemical formula Ba2-(x+y) SrxMgyWO5. From transmittance measurements the values of optical band gap were estimated for the amorphous (Eg= 5.15) and nanocrystalline (Eg=4.58 eV) phases. The presence of a lattice disorder was indicated by the high values of Urbach and weak absorption tail energies A decrease in their values was observed and attributed to the crystallization process and cation redistribution.

Subwavelength hole array (HA) metasurfaces support the so-called extraordinary optical transmission (EOT) resonance that has already been exploited for sensing. In this work, we demonstrate the superior performance of a different resonant regime of HA metasurfaces called anomalous EOT, by doing a thorough numerical and experimental study of its ability as a thin-film label-free sensor in the terahertz (THz) band. A comprehensive analysis using both the regular and anomalous EOT resonances is done by depositing thin layers of a dielectric analyte of different thicknesses on the structures in different scenarios. We carry out a detailed comparison and demonstrate that the best sensing performance is achieved when the structure operates in the anomalous EOT resonance and the analyte is deposited on the non-patterned side, improving by a factor between 2 and 3 the results of the EOT resonance in any of the considered scenarios. This can be explained by the comparatively narrower linewidth of the anomalous EOT resonance. The results presented expand the reach of subwavelength hole arrays for sensing applications by considering the anomalous EOT regime that is usually overlooked in the literature.

Gas membrane-based separation is considered one of the furthermost effective technology to address energy efficiency and large footprint challenges. Various classes of advanced materials including polymers, zeolites, porous carbons and metal–organic frameworks (MOFs) were attempted as membranes for gas separation. MOFs, among other porous materials, possess uniquely tunable nature, in which the pore size and environment can be controlled by connecting metal ions (or metal ion clusters) with organic linkers with various functionalities. This feature makes them attractive for thin membrane fabrication, as both diffusion and solubility components of permeability can be altered. It is interesting to notice that numerous reports have addressed the synthesis of different MOFs, fabrication of their corresponding thin films and their applications, nonetheless, relatively limited studies addressed their gas separation application as membranes. In this review, we provide a synopsis of the various MOF-based membranes that were fabricated in the last decade. In this review we propose a short introduction touching on the gas separation membrane technology and we shed light on (i) the various techniques developed for the fabrication of MOF as membranes and (ii) challenges and application for MOF thin film membranes in various important gas separation applications.

This work is devoted to physical vapor deposition synthesis, and characterisation of bismuth and lutetium-substituted ferrite-garnet thin-film materials for magneto-optic (MO) applications. The properties of garnet thin films sputtered using a target of nominal composition type Bi_0.9Lu_1.85Y_0.25Fe_4.0Ga₁O₁₂ are studied. By measuring the optical transmission spectra at room temperature, the optical constants and the accurate film thicknesses can be evaluated using Swanepoel’s envelope method. The refractive index data are found to be matching very closely to these derived from Cauchy’s dispersion formula for the entire spectral range between 300-2500 nm. The optical absorption coefficient and the extinction coefficient data are studied for both the as-deposited and annealed garnet thin-film samples. A new approach is applied for accurately deriving the optical constants data simultaneously with the physical layer thickness, using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method. MO properties, such as specific Faraday rotation, MO figure of merit and MO swing factor are also investigated for several annealed garnet-phase films.

This paper reviews several techniques, including analytical theories and real frequency techniques, to design ultra-wideband impedance matching networks for low-power applications. The comparison of solutions obtained using the simplified real frequency technique to the published solution using Chebyshev filter theory is demonstrated.

Background: The level of food processing has gained interest for a potential determinant of human health. The aim of this study was to assess the relation between level of food processing and prostate cancer severity. Methods: A sample of 120 consecutive patients were examined for their dietary habits assessed through validated food frequency questionnaires, their dietary intake of food groups categorized according to the NOVA classification, and the severity of prostate cancer according to the European Association of Urology (EAU) guidelines groups risk. Uni- and multivariate logistic regression analyses were performed to test the association between the variables of interest. Results: Individuals reporting higher consumption of unprocessed/minimally processed foods were less likely to have worse prostate cancer severity than lower consumers in the energy-adjusted model [odds ratio (OR) = 0.38, 95% confidence interval (CI): 1.17-0.84, P = 0.017 and OR = 0.33, 95% CI: 0.12-0.91, P = 0.032 for medium/high vs. low grade and high vs. medium/low grade prostate cancers, respectively); however, after adjusted for potential confounding factors, the association was no more significant (Table 4). A borderline association was also found between higher consumption of UPF and worse prostate cancer severity in the energy-adjusted model (OR = 2.11, 95% CI: 0.998-4.44; P = 0.051), but again the association was no more significant after adjusting for the other covariates. Conclusions: The level of food processing seems not to be independently associated with prostate cancer severity, while potentially related to other factors that need further investigation.

As solar energy is a low-cost and clean energy source, there has been a great deal of interest in how to harvest it. To absorb solar energy efficiently, we have designed a broadband metamaterial absorber based on the principle of Fabry–Pérot (FP) cavity and surface plasmon resonances (SPRs). We propose a broadband perfect absorber consisting of a four-layer structure of silica-tungsten-silica-titanium (SiO2-W-SiO2-Ti) for the incident light wavelength range of 300–2500 nm. The structure achieves perfect absorption of incident light in the wavelength range of 351.8–2465.0 nm (absorption >90%), with an average absorption of 96.3%. The advantage of our proposed structure is that it combines the characteristics of both high and broadband absorption and has a high overall absorption efficiency for solar radiation. It is also independent of polarization and insensitive to incident angle. We investigated how absorption was affected by different structures, materials, geometrical parameters, and refractive indices for different dielectric materials, and we explored the reasons for high absorption. This structure is refractory and ultra-thin, and it offers a good trade-off between bandwidth and absorption. It therefore has premium application prospects and value.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

Fabrics treated to repel water, superhydrophobic, and water and oil, superamphiphobic, have numerous industrial and consumer-level benefits. These coatings are typically non-permanent. This is largely due to chemical or physical changes of the coating to prolonged exposure to relatively harsh environments. To develop more durable fabric treatments for specific applications, it is necessary to measure the extent to which the treated fabrics retain their low-wettability after being subjected to controlled aggressive environmental conditions. In this study, plain weave fabrics made from polyester filaments and coated with silicone nanofilaments in-solution were exposed to aerodynamic icing conditions. The coated fabrics showed superhydrophobic behavior, or superamphiphobic for those that were fluorinated. The wettability of the fabrics was progressively evaluated by contact angle and roll-off-angle measurements. The fabrics were able to maintain their low-wettability characteristics after exposure to water droplet clouds at airspeeds up to 120 m/s, despite damage to the silicone nanofilaments, visible through scanning electron microscopy.

An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

Liposome vesicle is an ideal carrier for carbon nanotube (CNT) to serve as the water channel that allows the fast transport of water molecules, and thus enhancing the membrane permeability. However, low quantity of the inserted CNT in the liposome vesicle is an important factor that limited further improvement of the membrane flux. In present study, positively charged lipids (2,3-dioleoyloxy-propyl)-trimethylammonium-chloride (DOTAP) was introduced to the 1,2-dioleoyl-sn-glycero-3-phosphoethanolamineon (DOPE) liposome vesicles to tailor the vesicle charge, so as to evaluate the effect of positively charged DOTAP on the insertion of CNT into liposomes and separation performance of thin-film nanocomposite (TFN) membranes. The results showed that addition of DOTAP induced more quantity of CNT inserted into the liposome vesicles, since the shrinkage rate (k) and permeability (Pf) of liposome vesicles present obvious increase with increased content of DOTAP in the liposome vesicles. Besides, it contributed to 252.3% higher water flux for TFN membranes containing DOPE/DOTAP2:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 2:1) than TFC membranes. More important, it presented 106.7% higher water flux for TFN membranes containing DOPE/DOTAP4:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 4:1), which was originated from the more water channels that the CNT provided in the liposome vesicles. In all, positively charged DOTAP effectively tailored the vesicle charge, which provided a better carrier for the insertion of more quantity of CNT, and contributed to higher permeability of TFN membranes.

The main aspects of mercury sulfide and mercury selenide thin film synthesis using the chemical deposition method are considered. An analysis of various factors affecting film properties was conducted, including the study of how the nature of the substrate and its pre-treatment influence film properties. The effects of the working solution's temperature, deposition time, and annealing conditions on film characteristics were investigated. The impact of these parameters on the phase composition, as well as optical, electrical, and morphological properties of the films, is discussed and summarized. The paragraph also explains how the choice and concentration of initial reagents affect the parameters, characteristics, and properties of the obtained films.

New TLC-densitometric method have been developed for the identification and quantification of paracetamol (PA), propyphenazone (PP) and caffeine (C) of Saridon tablets using the NP-TLC technique combined with densitometry. This method allows for the simultaneous determination of PA, PP, and C in the same sample. Among all tested chromatographic conditions, the mixture consisting of chloroform + toluene + ethyl acetate + ethanol + acetic acid (18:18:7.5:5.0:0.3, v/v) and silica gel 60F254 plate proved to be the most effective for the separation of three tested active pharmaceutical ingredients (APIs) and substances related to paracetamol. The fully validation of the proposed NP-TLC method proves that it is specific, precise, accurate, robust and sensitive. The percentage content in relation to the content declared by the manufacturer is for propyphenazone 99.8%, paracetamol 101.6% and caffeine 100.8%, which are in accordance with pharmacopoeial requirements. The results presented indicate the possibility of using the developed method in the routine control of pharmaceutical preparations containing these APIs. The proposed method is economical and more sensitive compared to the previously proposed planar methods for the simultaneously determination of PA, PP and CAPIs. Will be an What is more, the presented method may be anaxcellent excellent economical alternative when HPLC method is unavailable for such determination.

Hard coatings like Titanium diboride (TiB2) on silicon substrates are used for interconnects. micro-electro-mechanical devices and metallurgical protective coatings were analyzed based on shallow depths of nanoindentation penetration which involves a change in the nature of the contact from Hertzian to Pyramidal both in loading as well as unloading modes. Features like ductile fracture, linear unloading, and the creation of electrical conduction paths were analyzed. These high-precision features are influenced by the thickness and crystalline nature of the films and are significant for device fabrication.

A method based on ferroelectric dipole to enhance surface charge density of triboelectric generator was proposed. By using the ferroelectric properties of polyvinylidene fluoride (PVDF), a positive charge trap was formed in the triboelectric layer to enhance the electric generating performance of the triboelectric material, so as to improve the surface charge density of the triboelectric nanogenerator. The PVDF film was fabricated by casting and uniaxial tensile process, and integrated into the triboelectric nanogenerator with vertical separation structure. The influences of the embedding direction, thickness and polarization intensity of the PVDF film on the output of the triboelectric nanogenerator were systematically studied. The results showed that the embedded PVDF piezoelectric film with a thickness of 100 µm and a maximum polarization electric field of 90 MV/m increased the peak power of the triboelectric nanogenerator by 2.6 times. This work has provided a new insight into regulating the properties of the triboelectric nanogenerator.

We carry out in a thin heterogeneous porous layer, the multiscale analysis of Smoluchowski's discrete diffusion-coagulation equations describing the evolution density of diffusing particles that are subject to coagulate in pairs. Assuming that the thin heterogeneous layer is made of microstructures that are uniformly distributed inside, we obtain in the limit an upscaled model in lower space dimension. We also prove a corrector-type result very useful in numerical computations. In view of the thin structure of the domain, we appeal to a concept of two-scale convergence adapted to thin heterogeneous media to achieve our goal.

Mixed cadmium tellurides – cadmium sulfides thin layers were formed on the polyamide PA 6. Monotelluropentathionic acid (H2TeS4O6) was used as precursor of tellurium and sulfur. We applied a low-temperature, nontoxic and cost-effective SILAR method. Cadmium telluride (CdTe) and sulfide (CdS) layers were formed through consecutive reactions of sorbed/diffused chalcogens species from telluropentathionate anion (TeS4O62–) with functional groups of polyamide and alkaline cadmium sulfate. The pseudo-second-order rate and Elovich kinetic models best fitted to quantify an uptake of chalcogens and cadmium on PA6. The effects of chalcogens and Cd on the structure and optical properties of PA6 were characterized using UV/Vis and IR spectra. The clear changes of these properties found in dependence on the concentration and exposure time in precursor's solutions. Fourier transform infrared spectroscopy and an ultraviolet-visible spectroscopy were applied in order to evaluate the effect of the chalcogens having particles on the changes in structure of polyamide 6 films depending on the exposure time in the solution of the chalcogens precursor and its concentration. The optical band gap energy of formed layers was found to be in the order of 1.52–2.36 eV. Studies of scanning electron microscopy and atomic force microscopy reveal that the diameter of the average grain is about 30 nm. The grains are conical in shape and unevenly distributed all over the surface of the substrate.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

In this work, a highly efficient, molybdenum disulfide (MoS2) based near infrared (NIR) heterojunction photodetector is fabricated on a Si substrate using a cost-effective and simple drop casting method. A non-stoichiometric and inhomogeneous MoS2 layer with a S/Mo ratio of 2.02 is detected using energy dispersive X-ray spectroscopy and field emission scanning electron microscope analysis. Raman shifts are noticed at 382.42 cm-1 and 407.97 cm-1, validating MoS2 thin film growth with a direct bandgap of 2.01 eV. The fabricated n-MoS2/p-Si photodetector is illuminated with a 785 nm laser at different intensities, and demonstrate the ability of the photodetector to work in both regions, the forward biased and reverse biased from above 1.5 V and less than -1.0 V. The highest responsivity, R is calculated to be 0.52 A/W while the detectivity D* is 4.08 x 10^10 Jones for an incident light intensity of 9.57 mW/cm2. The minimum rise and fall times are calculated as 1.77 ms and 1.31 ms for an incident laser power of 9.57 mW/cm^2 and 6.99 mW/cm^2 respectively at a direct current bias voltage of 10 V. The demonstrated results are promising for the low-cost fabrication of a thin MoS2 film for photonics and optoelectronic device applications.

A thin-shell wormhole is crafted by the cut-and-paste method of two Bardeen de-Sitter black holes using Darmois-Israel formalism. Energy conditions are considered for different values of magnetic charge while both mass and cosmological constant are fixed. The attractive and repulsive characteristics of the throat of the thin-shell wormhole are also examined through the radial acceleration. Dynamics and stability of the wormhole are studied around the static solutions of the linearized radial perturbations at the throat of the wormhole. The regions of stability are determined by checking out the condition of concavity of the potential as a function in the throat radius for different values of magnetic charges.

tructural and superconducting properties of high quality Niobium nanofilms with different thicknesses are investigated on silicon oxide and sapphire substrates. The role played by the different substrates and the superconducting properties of the Nb films are discussed based on the defectivity of the films and on the presence of an interfacial oxide layer between the Nb film and the substrate. The X-ray absorption spectroscopy is employed to uncover the structure of the interfacial layer. We show that this interfacial layer leads to a strong proximity effect, specially in films deposited on a SiO2 substrate, altering the superconducting properties of the Nb films. Our results establish that the critical temperature is determined by an interplay between quantum-size effects, due to the reduction of the Nb film thicknesses, and proximity effects.

In this study is reported the optical, structural and dielectric properties of Poly (vinyl alcohol) thin films membranes with embedded ZnO nanoparticles (PVA/ZnO) obtained by solution casting method at low temperature of deposition. Fourier Transform Infrared spectra showed the characteristics peaks, which correspond to O-H and Zn-O bonds present in the hybrid material. The X-ray diffraction patterns indicated the presence of ZnO structure into the films. The composite material showed low absorbance and a wide band gap energy from 5.6 to 5.9 eV. The surface morphology for the thin films of PVA/ZnO was studied by Atomic Force Microscopy and Scanning Electron Microscopy. The dielectric properties of the nanocomposites were measured from low to high frequencies, the results showed a high dielectric constant (ε) in the order of 10⁴ at low frequency and values from ε ≈ 2000 to 100 in the range of 1KHz-1MHz respectively, the properties of PVA/ZnO such as the high permittivity and the low temperature of processing make it a suitable material for potential applications in the development of flexible electronic devices.

The dislocation density tensors of thin elastic shells have been formulated explicitly in terms of the Riemann curvature tensor. The formulation reveals that the dislocation density of the shells is proportional to KA3=2, where K is the Gauss curvature and A is the determinant of metric tensor of the middle surface.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Hydrogen fuel is gaining particular attention in internal combustion engines. In addition to zero-carbon emissions, major advantages relate to its combustion characteristics, which allow significant increase in thermal efficiency under ultra-lean operation and with very low NOx levels. The ignition system is one of the main technology enablers, as it determines the capability to control ultra-lean operations, avoid backfire phenomena, or reduce the risks of abnormal combustions. The latter results from the hydrogen low ignition energy and it is associated with factors like high-temperature residuals, hot spots, and irregular spark plug discharge. ACIS gen 2-Barrier Discharge Igniter excels in accelerating the initial flame growth speed by the generation of non-equilibrium low-temperature plasma, strong ignition promoter for the combined action of kinetic and thermal effects. Moreover, its volumetric discharge facilitates combustion initiation on a wide region, in contrast to the localized ignition of traditional spark systems. In this work we present for the first time, to the best of our knowledge, experimental results showing the performance of a hydrogen engine with a low-temperature plasma discharge. Tests were conducted on a single-cylinder research engine, achieving ultra-lean conditions with cycle-to-cycle variability results below 2.5%. The analysis indicates that the H2 - BDI combined solution is capable of accelerating the evolution of the flame front compared to traditional spark plugs, leading to a significant reduction in the cycle-to-cycle variability. A meticulous adjustment of the BDI control parameters further enhances igniter performance and contributes to a deeper understanding of the innovative approach proposed in this study.

in this article, an ultra-wideband traveling wave antenna with antipodal topology is proposed. The proposed design is realized on an economical substrate with minimum thickness. The proposed design offers an ultra-wide bandwidth of 26 to 40 GHz, translating to 42%. The dimensions of the antenna are 20mm x10mm x 0.5mm indicating an electrically compact structure. The proposed antenna offers high front to back ratio of at least 10dB across the bandwidth of operation. The forward gain of the antenna varies from 4 to 7dBi in the afore-mentioned band. The pattern integrity is maintained throughout the band. The antenna is fabricated using the commercial photolithography process. A mutli-step topology of the antennas is also proposed for wide angular coverage. The coverage is greater than 150º with mutual coupling less than 25dB. These performance metrics is achieved with a very small footprint. Simulated and experimental results are presented in this paper.

In this work, we present a transceiver front-end in SiGe BiCMOS technology that can provide an ultra-wide bandwidth of 100 GHz at millimeter-wave frequencies. The front-end employs a novel configuration for low-loss distribution of broadband generated pulses as well as coherent spatial combining of received pulses. This leads to the realization of a fully integrated ultra-high-resolution imaging chip for biomedical applications. We realized an ultra-wide imaging bandwidth of 100 GHz by the integration of two adjacent, disjointed frequency sub-bands of 10–50 GHz and 50–110 GHz respectively. The transceiver front-end is capable of both transmit (TX) and receive (RX) operations. This is a key building-block for a scalable system in which a unit cell is repeated in the X and Y directions resulting in less power and area consumption. The imaging elements were designed and fabricated in Global Foundry 130-nm SiGe 8XP BiCMOS process technology.

The modern diet, which consists of food produced with high level of industrial processing, is associated with an increased risk of the development of lifestyle diseases. Current nutritional science is, however, focused on chemical composition of food, and not on the type and degree of processing used during the food production. Here, we take a fresh perspective on the relationship between the extent and type of food processing, and evaluate its impact on consumer health. We argue that the preference for consumption of minimally processed foods, and restriction of ultra-processed foods should be an essential part of a healthy lifestyle, disease prevention, and even treatment. We also present a simple, user-friendly consumer guide, which is intended to be used as a practical, ready-to-go identifier of ultra-processed foods.

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

A novel method based on a hybrid incremental modeling approach has been designed and applied to imbalance detection in ultra-high precision rotating machines. The model is obtained by a two-step iterative process that combines an overall model (least-squares fitting) with a local model (fuzzy k-nearest-neighbour) to take advantage of their complementary capacities. Three normalization strategies of evaluating the effect on accuracy are analyzed. A comparative study demonstrates that the hybrid incremental model provides better error-based performance indices for detecting imbalance than a nonlinear regression model and an adaptive neural-fuzzy inference system model. The suitability of Mahanolobis normalization for hybrid incremental modeling is also demonstrated in this case study. The proposed strategy for imbalance detection is simple, fast, and non-intrusive, reducing the deterioration in the performance of ultra-high precision rotating machines due to vibrations.

The aim of this study was to examine the oxidation of human serum albumin (HSA) caused by oxidative stress after an exhaustive exercise such as ultra-marathon race. Thus, blood samples from 12 adult runners who underwent a 103 km mountain ultra-marathon race were collected pre- and 24, 48 and 72 h post race. HSA was partially purified using affinity chromatography and then was subjected to Western blot analysis for disulfide dimers determination, indicating oxidation. The results were correlated with those from a previous study in which the same samples were analyzed using different oxidative stress markers and a good correlation with protein carbonyls (PC) at all time points was observed. Moreover there was a significant correlation with static oxidation-reduction potential (sORP) at 24 h, and a negative correlation with capacity oxidation-reduction potential (cORP) at 24 and 48 h. In addition, an individual analysis of albumin dimers exhibited great inter-individual differences. This inter-individual variability in the oxidation of HSA may suggest different interventions (e.g. through diet) in order to confront the effects on athletes’ organism after a strenuous exercise. In conclusion, this study supported the importance of the assessment of albumin dimers as a predictive marker for exercise-induced oxidative stress.

The exchange coupling between two ferromagnetic thin films, one with magnetically hard and the other with soft phases, separated by a thin non-magnetic layer is studied. Nd-Fe-B/ Ti / Fe thin film heterostructures were fabricated using DC magnetron sputtering on Si substrates which were heated in situ at 650°C using a house-built vacuum-compatible heater. The effect of the thickness of the Ti buffer layer and the annealing temperature on the formation of various phases of NdFeB was investigated. The effect of the thickness of the non-magnetic Ti spacer layer on the exchange coupling strength between the hard phase Nd-Fe-B ferromagnetic thin layer and the soft phase transition metal Fe layer was experimentally investigated. Hysteresis loops of multilayer thin films indicate an antiferromagnetic coupling was observed when the thickness of the spacer layer was 2 nm. This is within the range of antiferromagnetic coupling calculation based on RKKY theory predictions.

Valsartan (Val) is an important antihypertensive medication with side effects such as dizziness and angioedema. These constraints are due to the low oral bioavailability and relatively short half-life. The goal here is to incorporate Val into a mixed micelles system that can enhance transdermal delivery. Thin-film hydration and micro-phase separation were used to produce Val-loaded mixed micelle systems. A variety of factors, including surfactant type and drug-to-surfactant ratio, were optimized to produce micelles with low size and high Val entrapment efficiency (EE). The size, polydispersity index (PDI), zeta-potential, and drug entrapment efficiency of the prepared micelles were all measured. The drug release profiles in vitro were assessed using dialysis bags, and the permeation through abdominal rat skin was assessed using a Franz diffusion cell. All formulations had high EE levels exceeding 90% and low particle charges. The micellar sizes ranged from 107.6 to 191.7nm, with average PDI values of 0.3. The in vitro release demonstrated a uniform slow rate that lasted one week with varying extents. F7 demonstrated a significant (P < 0.01) transdermal efflux of 68.84 ± 3.96 µg/cm2/h through rat skin when compared to the control. As a result, the enhancement factor was 16.57. Val-loaded mixed micelles were successfully prepared using two simple methods with high reproducibility, and extensive transdermal delivery was demonstrated in the absence of any aggressive skin modifying enhancers.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

We propose an experimental method for the unidirectional excitation of spin waves. By structuring Au nanowires arrays within a coplanar waveguide onto a thin yttrium iron garnet (YIG) film, we observe a chiral coupling between the excitation field geometry of the nanowires grating and several well-resolved propagating magnon modes. We report a propagating spin wave spectroscopy study with unprecedented spectral definition, wavelengths down to 130 nm and attenuation lengths well above the 100 μm over the 20 GHz frequency band. The proposed experiment paves the way for future non-reciprocal magnonic devices.

Hydrotalcites (HTlc) represents a class of nanostructured layered materials that may be employed in a variety of applications, from green to bio technologies. In this paper, we report an investigation on HTlc made of Mg and Fe, recently employed to improve the growth in vitro of osteoblasts within a keratin sponge. We have carried out an analysis of powder materials and of HTlc dispersed in keratin and spin-coated on a Si/SiO2 substrate at different temperatures. A DC magnetic study of the powders has been carried out with a Quantum Design Physical Property Measurement System, equipped with a Vibrating Sample Magnetometer. The data gathered prove that these HTlc are fully paramagnetic, and keratin shows a very small magnetic response. Optical and Atomic Force Microscopy analyses of the thin films provide a detailed picture of clusters randomly dispersed in the films with various dimensions. The magnetic properties of these films have been characterized using the Nano Magneto Optical Kerr Effect (NanoMOKE) down to 7.5K. The data collected show that the local magnetic properties can be mapped with a micrometric resolution distinguishing HTlc regions from keratin ones. This approach opens new perspectives in the characterization of these composite materials.

Fibreglass composite plates are used for applications ranging from aerospace and automotive industries to construction industry. Vibroacoustic properties of the fibreglass plate has been investigated for different boundary conditions. The theory of the plate vibration and sound radiation has been used to determine the deflection of the composite plate at different locations on its surface. 3-Dimentional (3D) deformations and their corresponding contour velocities of plate have been computed for a range of frequencies. It has been shown that clamping the plate at four edges delayed first resonance of the plate by 15 Hz and second resonance of the plate by 30 Hz. Vibroacoustic indicators and the radiation impedance matrix of the plate have also been calculated. The results of this study show that fibreglass plate could be used in building industry to dampen the vibration of machine and structural vibration of buildings, and to sandwich building structures to form panels in order to attenuate airborne sound and to lower noise transmission of structural borne sound

In this paper, a novel synthesis for a chemical precursor for nanocrystalline VO2 coatings is elaborated. The compatibility of the precursor towards the substrate is optimized for spin coating. This is done by subjecting multiple solvents to contact angle measurements. A suitable thermal treatment is developed to densify the coating and to induce crystallization. Afterwards the microstructure of the coating is investigated using X-Ray diffraction, electron microscopy and ellipsometry techniques. To assess the thermochromic properties of the fabricated device, optical transmission experiments were conducted both at room temperature and at elevated temperature. A correlation between these thermochromic properties and coating thickness was investigated in order to obtain an optimized thermochromic device, where both high visual transparency and prominent thermochromic switching abilities are aimed for. In this work, an optimal coating thickness is proposed for a thermochromic coating with high switching ability and solar modulation.

An equilibrium problem of the Kirchhoff-Love plate containing a nonhomogeneous inclusion is considered. It is assumed that elastic properties of the inclusion depend on a small parameter characterizing width of the inclusion $\varepsilon$ as $\varepsilon^N$ with $N<1$. The passage to the limit as the parameter $\varepsilon$ tends to zero is justified, and an asymptotic model of a plate containing a thin inhomogeneous hard inclusion is constructed. It is shown that there exists two types of thin inclusions: rigid inclusion ($N<-1$) and elastic inclusion ($N=-1$). The inhomogeneity disappears in the case of $N\in (-1,1)$.

The light response and resistance switching behavior in BaTiO3 (BTO) films are studied for a symmetric Pt/BTO/Pt structure. The resistance of films as a function of time with and without ultraviolet light has been studied. Furthermore, resistance switching behavior was clearly observed based on the application of 365 nm wavelength ultraviolet light. Consequently, the polarities of resistance switching can be controlled by ultraviolet light when the energy is larger than the band excitation energy. It is proposed that the polarity of the resistance switching is dictated by the competition of the ferroelectricity and oxygen vacancy migration. This provides a new mechanism for modulating the state of ferroelectric resistive memory devices.

In this paper, we study the sensing performance of metasurfaces comprised by spiral-disk-shaped metallic elements patterned on polypropylene substrates, which exhibit localized surface plasmon resonances in the low-frequency region of the THz spectrum (0.2-0.5 THz). Optimal designs of spiral disks with C-shaped resonators placed near the disks were determined and fabricated. The experimentally measured transmittance spectra of samples coated with very thin photoresistive layers (d ~ 10^-4-10^-3 λ) showed good agreement with simulations. The resonance frequency shift Δf increases with increasing d, while saturating near d = 50 µm. The narrow-band magnetic dark modes excited on symmetrical spiral disks with a 90⁰-C-resonator demonstrated very high FOM values reaching 1670 [RIU·mm]^-1 at 0.3μm-thick analyte. The hybrid high order resonances excited on asymmetrical densely packed spiral disks showed about two times larger FOM values (up to 2950 [RIU·mm]^-1) as compared to symmetrical distantly spaced spirals that resembles the best FOM results found in literature for metasurfaces fabricated with a similar technique. The demonstrated high sensing performance of spiral disks is evaluated to be promising for bio-sensing applications in the THz range.

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

The application of geophysical methods for the characterization of geomorphologic subsurface features has become very popular in recent years. Convential geophysical applications on undifferentiated and weathered slopes have been less effective. Multichannel analysis of surface waves (MASW) is a new hope for the solution of the problem. MASW methods was used to the first step in order to reconstruct the ancient eruption of Mount Samalas. MASW was applied to the remnants of ancient volcanic sediment on Lombok Island to determine the physical and physical characteristics of seismic subsurface features. This paper is also discussion the application's capabilities of the MASW method on undifferentiated and weathered volcanic deposits on the slope area and classified them. The results of the research show that MASW technique is powerful in characterizing and delineating the stratum of the layers of undifferentiated and weathered volcanic precipitation areas. MASW is able to predict subsurface structures, especially for shallow and thin layers and presenting site class information for internal structure (vertical resolution). Based on S wave velocity structure, undifferentiated and weathered volcanic layer, genes are classified into site class C, D, and E. In the future, this method will completed with combination of other geophysical method and parameters variation (frequency and spaces) for isopach mapping of volcanic sediment and then analysis of ancient volcanic eruption dynamics.

Ultrathin Bi₂Se₃-NbN bilayers comprise a simple proximity system of a topological insulator and an s-wave superconductor for studying gating effects on topological superconductors. Here we report on 3 nm thick NbN layers of weakly connected superconducting islands, overlayed with 10 nm thick Bi₂Se₃ film which facilitates enhanced proximity coupling between them. Resistance versus temperature of the most resistive bilayers shows insulating behavior but with signs of superconductivity. We measured the magnetoresistance (MR) of these bilayers versus temperature with and without a magnetic field H normal to the wafer (MR=[R(H)-R(0)]/\{[R(H)+R(0)]/2\}), and under three electric gate-fields of 0 and ±2 MV/cm. The MR results showed a complex set of gate sensitive peaks which extended up to about 30 K. The results are discussed in terms of vortex physics, and the origin of the different MR peaks is identified and attributed to flux-flow MR in the isolated NbN islands and the different proximity regions in the Bi₂Se₃ cap-layer. The dominant MR peak was found to be consistent with enhanced proximity induced superconductivity in the topological edge currents regions. The high temperature MR data suggest a possible pseudogap phase or a highly extended fluctuation regime.

Stenting is an alternative to endarterectomy for the treatment of carotid artery stenosis. However, stenting is associated with a higher risk of procedural stroke secondary to distal thromboembolism. Hybrid stents with a micromesh layer have been proposed to address this complication. We developed a micropatterned thin film nitinol (M-TFN) covered stent designed to prevent thromboembolism during carotid intervention. This innovation may obviate the need or work synergistically with embolic protection devices. The proposed double layered stent is low-profile, thromboresistant, and covered with a M-TFN that can be fabricated with fenestrations of varying geometries and sizes. The M-TFN was created in multiple geometries, dimensions, and porosities by sputter deposition. The efficiency of various M-TFN to capture embolic particles was evaluated in different atherosclerotic carotid stenotic conditions through in vitro tests. The covered stent prevented emboli dislodgement in the range of 70-96% during 30min duration tests. In vitro vascular cell growth study results showed that endothelial cell elongation, alignment and growth behaviour silhouettes significantly enhance specifically on the diamond-shape M-TFN with the dimensions of 145µm×20µm and a porosity of 32%. Future studies will require in-vivo testing. Our results demonstrate that M-TFN has a promising potential for carotid artery stenting.

Electrostatic endothelial cell seeding has evolved as an exceptional technique to improve the efficiency of cell seeding in terms of frequency of attached cells and the amount of cell adhesion for the treatment of vascular diseases. In the recent times, both untreated and superhydrophilic thin film nitinol (TFN) have exhibited strong prospect as substrates for creation of small-diameter endovascular grafts due to their hallmark properties of superelasticity, ultra low-profile character, grown hemocompatible oxide layer with the presence of a uniform endothelial layer on the surface. The purpose of the current study is to understand the effects of endothelial cell seeding parameters (i.e., applied voltage, incubation time, substrate chemistry and cell suspension solution) to investigate the cell seeding phenomenon and to improve the cell adhesion and growth on the TFN surface under electrostatic transplantation. Both parallel plate and cylindrical capacitor models were used along with the Taguchi Design of Experiment (DOE) methods to design in vitro test parameters. A novel in vitro system for cylindrical capacitor model was created using a micro flow pump, micro incubation system, and silicone tubings. The augmented endothelialization on thin film nitinol was developed to determine the effect of cell seeding and deployed in a 6 Fr intravascular catheter setup. Cell viability along with morphology and proliferation of adhered cells were evaluated using fluorescent and scanning electron microscopy. Our results demonstrated that the maximum number of cells attached on STFN in the catheter was observed in 5V with the 2 hr exposure of in the cell culture medium (CCM) solution. The condition showed 5V voltage with 0.68×10-6 µC electrostatic charge and 5.11 V·mm-1 electric field. Our findings have first demonstrated that the electrostatic endothelialization on the superhydrophilic thin film nitinol endograft within the catheter prior to the endovascular procedure could enhance the biocompatibility for low-profile endovascular applications.

The straightness error of guideway is one of the key indicators of ultra-precision machine, which plays an important role in the machining accuracy of work-piece. In order to measure straightness error of long distance ultra-precision guideway accurately, a splicing measurement for straightness error of guideway using high-precision flat mirror and displacement sensor was proposed in this paper, and the data splicing processing algorithm based on coordinate transformation was studied. Then comparative experiments on splicing measurement and direct measurement of straightness error were carried out on a hydrostatic guideway grinder. The maximum difference between the two measurements was about 0.3μm, which was far less than the straightness error of 5.8μm. The experiment demonstrated the correctness of the proposed splicing measurement method and data processing algorithm. To suppress the influence of straightness error on machining accuracy, a straightness error compensation algorithm based on error rotation transformation and vertical axis position correction was proposed, and the grinding experiment of a plane optics with size of 1400mm×500mm was carried out, whose flatness error after grinding was about 2.98μm. The straightness error of the grinding machine had been well suppressed.

Liquid biopsy is a rapidly emerging field which involves the minimal/non-invasive assessment of signature somatic mutations through analysis of circulating tumor DNA (ctDNA) shed by tumor cells in bodily fluids. The broad, unmet need for liquid biopsy lung cancer detection is the lack of multiplex platform that can detect a mutation panel of lung cancer genes using minimum amount of sample, especially for ultra-short ctDNA (usctDNA). Here we developed a non-PCR and non-NGS-based single droplet based multiplexing microsensor technology “Electric Field-Induced Released and Measurement (EFIRM) Liquid Biopsy” (m-eLB) for lung can-cer-associated usctDNA. The m-eLB provides multiplexable assessment of usctDNA within a single droplet of biofluid in only one well of micro-electrodes, as each electrode coated with dif-ferent probes for the ctDNA. In this m-eLB prototype, it demonstrates accuracy for 3 tyrosine ki-nase inhibitor related EGFR target sequences in synthetic nucleotides. The accuracy for the multi-plexing assay has an AUC of 0.98 for L858R, Ex19del, AUC of 0.94 for Ex19 deletion and AUC of 0.93 for T790M. By combining the 3 EGFR assay together, the AUC was 0.97 for the multiplexing assay.

Excessive intake of fat and fatty acids is associated with major health hazards such as obesity or chronic diseases. The aim of this study was to provide the first data on total fat, saturated fatty acids (SFA) and trans fatty acids (TFA) intakes and their major food sources in Tunisian children. A total of 1200 children, aged 3 to 9 years old (yo), were randomly selected from primary schools and kindergarten under a cross-sectional design. The 24-hour recall method and food frequency questionnaire were used to assess dietary intake. The energy percentages of total fat, SFA and TFA in Tunisian children were respectively 29.6, 11.4 and 0.15. No sex differences were found. The WHO recommendations for total fat, SFA and TFA were adopted by 58 %, 39 % and 89 % of the study population, respectively. The leading food groups of fat and fatty acids were ultra-processed foods, breakfast cereals and dairy products. The meat, fish, eggs and fish alternatives were the fifth main contributors to the total fat and SFA intakes in Tunisian children. The implementation of a relevant strategy for fat reduction, especially from ultra-processed foods, considered as low nutrient energy-dense products, is needed to promote health among children and prevent diet-related chronic diseases.

The liquid droplet cooling technique for fast scanning chip calorimetry (FSC) is introduced, increasing the cooling rate for large samples on a given sensor. Reaching higher cooling rates and using a gas as the cooling medium, the common standard for ultra-fast temperature control in cooling, requires reducing the lateral dimensions of the sample and sensor. The maximum cooling rate is limited by the heat capacity of the sample and the heat exchange between the gas and the sample. The enhanced cooling performance of the new liquid droplet cooling technique is demonstrated for both metals and polymers, on examples of solidification of large samples of indium, high-density polyethylene (HDPE), and poly (butylene 2,6-naphthalate) (PBN). It was found that the maximum cooling rate can be increased up to 5 MK/s in room temperature environment, that is, by 2 orders of magnitude, compared to standard gas cooling. Furthermore, modifying the droplet size and using coolants at different temperatures provide options to adjust the cooling rate in the temperature ranges of interest.

Body acceleration due the heartbeat-induced reaction forces can be measured as smartphone accelerometer (m-ACC) signals. Our aim was to test the feasibility of using m-ACC to detect changes induced by stress by ultra-short heart rate variability (USV) indices (SDNN and RMSSD). Sixteen healthy volunteers were recruited; m-ACC was recorded while in supine position, during spontaneous breathing (REST) and during one minute of mental stress (MS) induced by arithmetic serial subtraction task, simultaneous with conventional ECG. Beat occurrences were extracted from both ECG and m-ACC and used to compute USV indices using 60, 30 and 10s durations, both for REST and MS. A feasibility of 93.8% in the beat-to-beat m-ACC heart rate series extraction was reached. In both ECG and m-ACC series, compared to REST, in MS the mean beat duration was reduced by 15% and RMSSD decreased by 38%. These results show that short term recordings (up to 10 sec) of cardiac activity using smartphone’s accelerometers are able to capture the decrease in parasympathetic tone, in agreement with the induced stimulus.

The Pierre Auger Observatory is the world's largest operating detection system for the observation of ultra high energy cosmic rays (UHECRs). The detector allows detailed measurements of their energy spectrum, mass composition and arrival directions of primary cosmic rays in the energy range above $10^{17}$ eV. The data collected at the Observatory over the last decade show the suppression of the cosmic ray flux at energies above $4\times10^{19}$ eV. However, it is still unclear if this suppression is caused by the propagation of cosmic rays or rather by energy limitation of their sources. The other puzzle is the origin of UHECRs. Some clues can be drawn from studying the distribution of their arrival directions. The recently observed dipole anisotropy has an orientation which indicates an extragalactic origin of UHECRs. The Auger surface detector array is also sensitive to showers due to ultra high energy neutrinos of all flavours and photons, and recent neutrino and photon limits provided by the Observatory can constrain models of the cosmogenic neutrino production and exotic scenarios of the UHECRs origin, such as the decays of super heavy particles. In this paper the recent results on measurements of the energy spectrum, mass composition and arrival directions of cosmic rays, and future prospects are presented.

As a part of the proposed article, the authors presented comprehensive data analysis for movement data that comes from a positioning system based on ultra-wide band (UWB) technology. For purpose of this article, a test was carried out during which the car equipped with cruise control overcame the given path at a speed from 10 km/h to 60 km/h. The obtained motion models (information about position) have been filtered through a series of filters - from fundamentals filters with a variable window (median, moving average, Savitzky-Golay filter), through more complex ones like the Wiener or Kalman filter. As a result, the authors proposed a form of data analysis and filtration depending on the speed of the moving object. In addition, the maximum accuracy that can be obtained for a given traffic model was also determined. The whole research proves that it is possible to use a system based on UWB technology in positioning objects for urban applications - smart city, in industry 4.0 applications as well as for positioning autonomous vehicles in urban applications, such as well as on highways to maintain cohesion of convoys vehicles.

When an earthquake or a large fire has occurred, it is difficult to secure communication networks for rescue in the building due to the destruction of commercial communication networks. Although analog radio systems such as VHF (very high frequency) and UHF (ultra-high frequency) are used for rescue operation in general, communication failure occurs in closed spaces, causing difficulties in smooth rescue operations. When the communication infrastructures have been destroyed in a building in the disaster, an emergency wireless telecommunication environment should be constructed to secure a safer disaster response environment. In this study, along with comparison of the performances of diverse communication frequencies, UWB (Ultra-Wide Band) wireless telecommunication networks were evaluated under five building indoor environment conditions including open spaces. UWB communication modules were fabricated to satisfy the IEEE (The Institute of Electrical and Electronics Engineers) 802.15.4a standard performance to measure distances in which communications are possible according to the indoor environment for each of six channels with different UWB communication frequencies. The results indicated that the distances in which communications are possible for each the six channels were average 15.5 m, maximum 20 m in open spaces; average 17.33 m, maximum 20 m in corridors; average 15.3 m, maximum 20 m in indoor office environments with office fixtures; average 4.33 m, maximum 6 m in vertical spaces of stairs; and average 6.5 m, maximum 17 m in closed horizontal spaces with a fire door. In this case, the communication performance and distance performance were shown to be the most excellent at a frequency (Centre Frequency) of 6489.6 and a band of 5980.3 – 6998.9 MHz, which is UWB 7ch. In conclusion, it is judged that if UWB communication modules are installed in the disaster area at intervals of 20 m and multi-channels are used, communication environments can be constructed even in closed spaces

In small-scale hydropower scheme, the most important component is electro-mechanical equipment. Since cost contribution of this component is high because hydrokinetic projects require negligible civil works. Turbine and alternator contribute major fraction of the hydrokinetic projects. Thus, there is a requirement to estimates the electromechanical equipment cost for the hydrokinetic hydropower scheme. The present paper investigates design parameters of the hydrokinetic turbines and intends to develop cost correlation which depends on most critical parameters of hydropower sites such as velocity and power capacity. In this present work, three zero head turbines are considered including straight blade Darrieus, two Stage Savonius, and Gorlov Helical. The size and cost of major components have been calculated based on material, manufacturing, research and design, and assembly costs. Based on cost and site parameters, cost correlation has been developed. The obtained cost has been validated with available zero head turbines in the market and installed projects. A techno-economic analysis has been carried out to select economical hydrokinetic turbine for river and canal application.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

In the autonomous navigation of mobile robots, precise positioning is crucial. In forest environments with weak satellite signals or in sites disturbed by complex environments, satellite positioning accuracy has difficulty in meeting the requirements of autonomous navigation positioning accuracy for robots. This article proposes a binocular vision SLAM/UWB tightly coupled localization method. The core of this algorithm is based on an Extended Kalman Filter (EKF), which utilizes the displacement increment output by binocular vision ORB-SLAM and the positioning coordinates calculated via UWB positioning as measurement information to achieve data fusion. The research utilized the constructed experimental platform to collect images and UWB ranging data in outdoor environments and experimentally validated the combined positioning method. The experimental results show that this algorithm outperforms the use of the individual UWB or visual SLAM localization methods in terms of positioning accuracy. Compared with traditional single positioning algorithms, this algorithm exhibits better practicality and stability, and can effectively suppress the impact of UWB non line of sight errors. The average error under normal line of sight conditions is 0.058 m, the root mean square error (RMSE) is 0.080, and the average error under non-line-of-sight conditions is 0.081 m, with an RMSE of 0.084. There is no significant jump or drift. Through the tightly coupled processing of binocular vision SLAM and UWB positioning, more reliable and accurate mobile robot positioning can be achieved, providing a useful reference for the autonomous navigation of mobile robots in complex environments.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

DEXTER (Detection of EXplosives and firearms to counter TERrorism) is a project funded by NATO’s Science for Peace and Security (SPS) program with the goal of developing an integrated system capable of remotely and accurately detecting explosives and firearms in public places without impeding the flow of pedestrians. The active microwave component of the DEXTER project is referred to as MIC (Microwave Imaging Curtain), supported by the French SGDSN (General Secretariat of Defense and National Security), and utilizes a radar system capable of generating 3D images in real time to address non-checkpoint detection of explosives and fire-arms. The project, led by the ONERA (France), is based on a radar imaging system developed by the Fraunhofer FHR institute, using a MIMO architecture with an Ultra Wide-Band waveform. Although high-resolution 3D microwave imaging is already being used in expensive body scanners to detect firearms concealed under clothing, MIC's innovative approach lies in utilizing a high-resolution 3D imaging device that can detect larger dangerous objects carried by moving individuals at a longer range, in addition to providing discrete detection in pedestrian flow. Automatic detection and classification of these dangerous objects is carried out on 3D radar im-ages using a deep-learning network. This paper will outline the project's objectives and constraints, as well as the design, architecture, and performance of the final system. Additionally, it will present real-time imaging results ob-tained during a live demonstration in a relevant environment.

Fleets of drones have attracted a lot of attention from the research community in recent years. One of the biggest challenges in deploying such systems is localization. While GNSS localization systems can only be effective in open outdoor environments, new solutions based on radio sensors (e.g., ultra-wideband) are increasingly being used for localization in various situations and environments. However, self-localization without prior knowledge of anchor positions remains an open problem which, for example, makes it impossible to track a moving target. In this article, we provide a comparison of different variants of gradient descent-based algorithms, with a new improved variant, for solving the localization problem using relative distance measurements and multilateration. It is applied to self-localization of anchors and tracking targets using ultra-wideband distance sensors. A realistic simulation of drone tracking and anchors’ localization is performed to demonstrate the robustness and accuracy of the proposed approach.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Under the big unified framework of quantum gravitational field and quantum repulsive field, the earlier in this series of work has comprehensively expanded the general relativity and loop quantum ring gravitation theory, set up the quantum repulsive field equation corresponding to the quantum gravitational field equation, and then established the quantum hedge-unified field equation describing the interaction of quantum gravitational field and quantum repulsive field; On this basis, the quantum repulsive universe equation corresponding to the quantum gravitational universe equation has be established, thus a set of new equations describing the expansive universe model under the condition of fully considering the hedge effect of quantum gravitational field and quantum repulsion field, which can be called the expansive universe equation of quantum hedge-unified field theory, has be established. Now, let's go deep into the arche-unified physics behind the creation of the universe. Although all kinds of inflationary universe models can solve cosmological problems to a certain extent, there is no natural and reasonable analysis and explanation for all cosmological and physical consequences. For example, it is impossible to predict a large tensor-scale ratio and a relatively large spectral index run at the same time. At present, string theory, membrane theory, loop quantum gravity theory, super-gravitational holography principle and M theory, which are the theoretical basis of cosmology, are basically established by simplification in the case of breaking away from the extreme background conditions of the universe. While cosmology, which is deficient in nature, cannot provide strong support for particle physics to further advance to a wider field and a deeper level. Due to the lack of new ideas, the construction of existing theoretical models is difficult. Therefore, the existing research can only be further promoted by new astronomical observation. Unlike existing studies, we concentrate on the emergence of the big rip-rebound clusters of quantum chaotic-reticulate distribution between the outwards-push of the universe as a whole (related to pseudo-vacuum energy, Higgs field, dark energy, etc.) and the inwards-pull of the universe in local scale (related to dark matter, quantum gravity and initial gravity separated from high-dimensional supergravity, and the initial strong force separated from the grand unified force subsequently). On the one hand, we find a great impetus to make the inflation of the universe into firstly-imposed suppression, then-imposed acceleration and finally-imposed deceleration, which really explains why the universe expands at a critical rate and has the same temperature in different regions, on the other hand, we find a fundamental unit of matter and its emerging clusters evolving in the big bang, inflation and expansion of the universe accompanied by the great rip-rebound clusters of quantum chaos-reticulate distribution, which can be reduced to an arche-pulsator of neither punctiform particle nor linear string. From these two aspects, it can been seen that the evolution of the early universe is much more complicated than people originally thought. The complexity of the super inflation of the universe is mainly reflected in the big rip-rebound cluster emerging behind the gravitational disturbance (the pressure and tensor disturbance related to dark matter), the repulsive disturbance (the pressure and scalar disturbance related to dark energy), the cosmological disturbance (related to the interaction between high-dimensional supergravity and high-dimensional superrepulsion). This is a system of nonlinear stochastic differential dynamics, or a quantum statistical physical process of nonlinear nonequilibrium state. In the new research paradigms established in this series, the arche-conjugation between the high-dimensional supergravity and the high-dimensional superrepulsion, as well as between the quantum gravity and the quantum repulsion, is higher than the supersymmetry, and then becomes the core concept of the new theory. In this series, cluster-inflating configuration, spin network space and cosmic paradigm vectors are proposed, so the model of the super-inflated universe with quantum chaos-reticulate distribution emerged under the great impetus. The new model reveals that the unified inflation of the universe as a whole and the local inflation of the universe emerge together in the great impetus of the big rip-rebound cluster of quantum chaos-reticulate distribution. As a spin network model variable, the spatiotemporal mode variable is a vector composed of a series of variables, which variables include: dimension, curvature, range, expansion speed, dynamics, quantization, chaotic-reticulate distribution (inhomogeneity, concentration, fluctuation), synergy, and so on. Between particle physics and cosmology, this series of papers proposes the cosmic quantum evolution mode, the physical-sphere distributing configuration and the interaction situation variables, organizes the concepts, variables and models of these three levels, and establishes a systematic super-synergy paradigm. In this paradigm, the general Langevan equation and the general Fokker-Planck equation are established. For the quantum cosmic-sphere, a series of trend parameters are introduced to establish the dynamics of quantum gravitational mode and its master equation, and then to establish the operator distribution function and its motion equation of the action mode. For the Tachyon of upheaval in the rip-rebound-inflating of the universe, the hypothesis on the bifurcate-chaos wave of quantum is given, the quantum theory of the early photons in upheaval is set up, and the analysis on the particles of the ultrahigh energy cosmic ray from the γ ray burst is made. Finally, using Wigner-Ville distribution as a nonlinear time-frequency distribution, we establish the ultra-synergistic field equation of quantum-classic unifying action-sphere.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

Ultra-weak photon emissions (UPEs) including those from human have been experimented for decades. The photo-genic origin of UPE has also been attributed to the oxidative stress or free radical production that is unique to metabolically active states of biological organisms. However, there are considerable gaps in quantitative understanding of UPE. In this work, I propose an analytical framework of hypothesis for the initial objective of modeling a few superficial presentations of UPE of human, including the systematic dependency on age, the diurnal variation, and the geometric asymmetry associated with serious asymmetrical pathological conditions. The hypothesis which is currently limited to human assumes a new form of energy state, termed vivo-nergy, which resides only in metabolically active organisms that are also under neuronal control. The hypothesis projects a decrease of the vivo-nergy in human during growth beyond puberty, with the rate of decrease dictated by a critical time-scale---the age of the first opposite-sex sexual intercourse (FOSSI). The hypothesis also proposes a modification of the vivo-nergy by the phases of systematic or homeostatic physiology. The hypothesis further postulates that the deviation of the physiology-modified vivo-nergy from the pre-puberty level is deteriorated by acquired organ-specific pathological conditions. Any reduction of vivo-nergy from the pre-puberty level is hypothesized to proportionally cause oxidative stress that functions as the physical source of UPE. The resulted steady-state diffusion of the photon emitted from a photo-genic source of UPE in a human geometry simplified as a homogeneous spherical domain is modeled by photon diffusion principles incorporating an extrapolated zero-boundary condition. The age and systematic physiology combined determines the intensity of the centered physiological photo-genic source. The acquired (single) pathology sets both the intensity and the off-center position of the (single) pathological photo-genic source. When the age-related, physiology-commanded, and pathology-controlled modifications of the photo-genetic sources are implemented in the photon diffusion model, the photon fluence rate at the surface of the simplified human-representing spherical domain reveals the dependency on age, the temporal variation corresponding to systematic physiology, and the geometric asymmetry associated with significant asymmetric pathological condition as reported previously for UPE. The hypothesis, as it provides analytical conveniences for quantitative estimation of UPE patterns, may be useful to further model-based interpretation of the spatial-temporal characteristics of UPE.

The VLSI industry is facing parasitic effects that trouble development in the nanoscale domain. However, instead of replacing the traditional MOSFET design, it would be more advantageous to apply different doping profiles and discerning which deal with specific parasitic effects the best. With a review of Gaussian doping, Uniform doping, and Delta doping profiles and analysis of the FET technology characteristics that use these doping profiles, a comparison can be made among them for integrated circuit design engineers. These doping profiles are compared based on how well they perform against non-ideal and ideal environments. Also, both digital and analog performance are measured to ensure the uniqueness of each doping profile that is present. After getting a list of benefits from each doping profile, it is derived to determine which doping profile works best against a host of parasitic effects and what type of application do these doping profiles have

The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.