Rescaling of rainfall requires measurements of rainfall rates over many dimensions. This paper develops one approach using 10 m vertical spatial observations of the Doppler spectra of falling rain every 10 seconds over intervals varying from 15 up to 41minutes in two different locations and in two different years using two different Micro-Rain Radars (MRR). The transformation of the temporal domain into spatial observations uses the Taylor ‘frozen’ turbulence hypothesis to estimate an average advection speed over an entire observation interval. Thus, when no other advection estimates are possible, this paper offers a new approach for estimating the appropriate frozen turbulence advection speed by minimizing power spectral differences between the ensemble of purely spatial radial power spectra observed at all times in the vertical and those using the ensemble of temporal spectra at all heights to yield statistically reliable scaling relations. Thus, it is likely that, MRR and other vertically pointing Doppler radars may often help to obviate the need for expensive and immobile large networks of instruments in order to determine such scaling relations, but not the need of those radars for surveillance.

The inter-tip times (ITTs) of tipping-bucket rain gauges potentially provide the highest-resolution intensity data that can be acquired from this type of gauge. At an intensity of 100 mm h-1, a typical gauge with a sensitivity of 0.2 mm of rainfall would be expected to tip every 7.2 seconds. However, TBRGs are often equipped with syphons, to reduce the dynamic calibration error that results from continued (and unmeasured) inflow to a bucket as it tips. This increases the accuracy of rainfall depth recording, but the time to fill and empty the syphon can reduce the ability of a TBRG to respond to (and for the ITTs to reflect) short-term intensity fluctuations. This ability is already limited by the discretisation arising from the filling and emptying of the buckets themselves. Laboratory tests with controlled water inflow rates were performed using two high-quality TBRGs, one a 'straight-through' design and the other syphon-equipped. These confirmed that at all intensities at which the syphon operates, a regular sequence of fixed-duration ITTs (such as the 7.2 s mentioned above) does not occur. Rather, the ITTs are perturbed by the syphon cycling. The gauges were also co-located in the field, and linked to carefully synchronised event data loggers. Data collected during several rainfall events revealed differences in the ITTs, and again confirm that the ITT sequence of a syphon-equipped TBRG exhibits artefacts related to syphon operation, that are not present in the 'straight-through' data. These artefacts can result in ITT differences of many minutes, depending on the rainfall intensity, and are problematic for the use of ITTs to estimate intensity. Peaks and troughs in the intensity profile also differed between the two gauges. It is recommended that in the application of TBRGs for studies where short-term intensity data are required, 'straight-through' gauges should be used, and syphon-equipped gauges avoided.

Very heavy stratiform precipitation (> 200 mm/per day) occurred in the Hokitika region on the west coast of the South Island of New Zealand on 18 June 2015, under north-westerlies with small CAPE (< 25 J/kg). Analyses of model simulations and observations showed that this heavy rainfall was due to cold front lifting enhanced by orographic lifting over the Southern Alps. At 1.5 km grid-length, the model terrain underestimated the average height of the 103 tallest mountains over the South Island by ~ 800 m. This leads to weaker orographic lifting and mountain blocking, and a faster-moving and stronger cold front in the Hokitika region. As a result, large errors in the heavy rainfall prediction occur. By increasing either the resolved or the sub-grid mountain heights, the simulated rainfall errors were largely reduced through stronger orographic lifting and mountain blocking, and a better simulation of the cold front movement and strength. All the experiments have the same “flow-over” regime with mountain waves and/or wave breaking (Fm ranges 0.61 – 1.21). However, the rainfall amount and distribution on the windward side of mountains altered significantly. Our new findings were that the Southern Alps can have significant indirect effects on heavy rainfall by altering the speed and strength of the cold front, in addition to the well-known direct dynamical effects (i.e., orographic lifting and mountain blocking). A combination of these direct and indirect effects makes the heavy rainfall simulation sensitive to mountain heights even under the same “flow-over” regime.

Field experiments were carried out during 2011-2014 at the Research and Experimental Center to Combating Desertification located in the Elsen Tasarkhai station of central Mongolia. The study was aimed to identify the effects of oxidized brown coal humic acid fertilizer on the relative growth rate of several trees for forest rehabilitation. The trees used were Populus sibirica, Salix ledebouriana and Acer tataricum. The experiment was carried out with the concentrations of 2,000, 10,000 and 20,000 mg L-1 of humic acid fertilization treatments. The measurement of relative height growth rate (RHGR) was conducted for a period of 4 years. The treatments showed significant differences within humic fertilizer concentrations which differed depending on the species. Compared to the monthly RHGR over the study, the treatment of fertilizers were significantly better for tree growth. P. sibirica in the 10,000 and 20,000 mg L-1 humic acid fertilizers had significant height growth rates. In addition, when the humic acid treatments were compared to control, A. tataricum decreased over the years which were statistically significant for high growth rate and a positive effect of humic acid fertilization treatments was observed. Furthermore, results showed that oxidized brown coal humic acid fertilizers as organic fertilizer can have a positive effect for the growth of A. tataricum during the study years. The results showed that the soil chemical properties EC, CO2, NO3, and K2O were significant among all the treatments compared to the control. The effect on P2O5 statistically significantly increased among all the treatments. However, pH and Mg were not significant effect among all the treatments. Combining the results obtained from the oxidized brown coal humic acid fertilization with sustainable land management practices can help improve soil organics for environmental issues in degraded sandy soil regions.

Using recent developments in econometrics and computational statistics we consider the estimation of the instantaneous rate of asset return process when the underlying Data Generating Mechanism (DGM) is an Ornstein-Uhlenbeck process, driven by fractional noise, and sampled at fixed intervals of length h. To address the problem we adopt throughout the paper an exact discretization approach. This enable us to exploit the fact that a flow sampling scheme arises naturally when observing the DGM. For, while the instantaneous rate of return process is unobservable at points in time, its time integral over successive observations is observable since it equals the increment of log-prices. Exact discretization delivers an ARIMA(1,1,1) model for log-prices with a fractional driving noise. Building on the resulting exact discretization formulae and covariance function, a new Markov Chain Monte Carlo (MCMC) scheme is proposed and we examine the properties of both the time and frequency domain likelihoods / posteriors through Monte Carlo. For the exact discrete model we adopt a general sampling interval of length h. This allow us to determine the optimal choice of h independent of the sample size. An empirical application using high frequency stock price data is presented showing the relevance of aggregation over time issues in modelling asset prices.

On the basis of the golden ratio and the compasseses, every angle was divided into three equal parts. In general, it has been proven that the problem of triangulation of an angle cannot be solved on the basis of the golden ratio and the expanding of the angle. The relationship of golden relativity with Pi number and Euler's number has not been investigated to solve impossible problems. According to the investigation of events in six-dimensional space-time, with the simultaneous movement of two arms of the compasses based on the golden ratio, every angle was divided into three equal parts. The growth rate based on the golden ratio is the key to solving the most intractable mathematical and physical problems.

Tests of selection based on population differentiation were performed on two highly polygenic traits important for success and quality of life: body height and educational attainment (EA). Polygenic scores (PGS) of EA and height, computed across three public genomic databases revealed differences between populations (1000 Genomes, HGDP, gnomAD) that matched the average IQ and height of ethnic groups (r ~0.9). A moderately strong correlation between latitude and EA PGS (r= 0.67) implies the effect of climate (seasonality or winter temperature) on selection for cognitive ability. The effect of latitude was reduced (β= 0.28) but remained significant after adding the sub-continental group variable to the regression model.The global Fst index revealed population differentiation at height and EA loci, significantly deviating from random SNPs. Substantial Linkage Equilibrium (LD) Decay between YRI and CEU was found (r= 0.6) but there was no correlation between LD decay and population differences in polygenic scores for EA (r= 0.015, p= 0.45), and slight inflation of height PGS difference due to LD decay (r= -0.04, p= 0.0315). Selecting the SNPs most robust to LD decay (r>0.8) resulted in larger PGS gaps for EA, but smaller for height. Finally, it is shown that PGS differences are more sensitive to the significance of GWAS loci than Fst, reflecting the major limitations of Fst as an index of selection.

Silicon Photomultipliers find applications across various fields. One potential Silicon Photomultiplier application domain is neutrino telescopes, where they may enhance the angular resolution. However, the elevated dark count rate associated with Silicon Photomultipliers represents a significant challenge to their widespread utilization. To address this issue, it is proposed to use Silicon Photomultipliers and Photomultiplier Tubes together. The Photomultiplier Tubes signals would serve as a trigger to mitigate the dark count rate, thereby preventing undue saturation of the available bandwidth. This paper presents an investigation into a fast and resource-efficient method for filtering Silicon Photomultiplier dark count rate. A low-resource and fast coincident filter has been developed, which removes the Silicon Photomultiplier dark count rate by using as trigger the Photomultiplier Tube input signals. The architecture of the coincidence filter, together with the first results obtained, which validate the effectiveness of this method are presented.

Precise monitoring of individual crop growth and health status is crucial for precision agriculture practices. However, traditional manual inspection methods are time-consuming, labor-intensive, and often lack the spatial resolution required for detailed analysis. This research addresses the need for efficient and high-resolution crop monitoring by leveraging Unmanned Aerial Vehicle (UAV) imagery and advanced computational techniques. The primary objective was to develop a methodology for precise identification, extraction, and monitoring of individual corn crops throughout their growth cycle. This was achieved by integrating UAV-derived data with image processing, computational geometry, and machine learning techniques. UAV imagery was ac-quired bi-weekly at altitudes of 40m and 70m, capturing the entire growth cycle of a corn crop from planting to harvest. A time-series Canopy Height Model (CHM) was generated by analyzing the differences between the Digital Terrain Model (DTM) and the Digital Surface Model (DSM) derived from the UAV data. Local spatial analysis and image processing techniques were em-ployed to determine the local maximum height of each crop. Subsequently, a Voronoi data model was developed to delineate individual crop canopies, successfully identifying 13,000 out of 13,050 corn crops in the study area. For enhanced accuracy in canopy size delineation, vegetation indices were incorporated into the Voronoi model segmentation, refining the initial canopy area esti-mates by eliminating interference from soil and shadows. The proposed methodology enables precise estimation and monitoring of crop canopy size, height, biomass reduction, lodging, and stunted growth over time, providing valuable insights for precision agriculture practices. This work contributes to the scientific community by demonstrating the potential of integrating UAV technology, computational geometry, and machine learning for accurate and efficient crop mon-itoring at the individual plant level.

Owing to the rising demand for vegetable soybean products, there is an increasing need for high-yield soybean varieties to raise the output. However, complex correlation patterns among quantitative traits with genetic interactions bring a challenge for vegetable soybean breeding. Here, a genome-wide association study (GWAS) was applied for six yield-related traits with 188 vegetable soybean accessions. A total of 81 SNPs were identified for pod length, plant height, pods number, pod thickness, pod width, and seed weight per plant by Blink model. Among these significant SNPs, 79 were novel SNPs, while 2 overlapped with previously reported SNPs. A total of 220 genes were found in 100 kb upstream and downstream regions of significant SNPs, of which 17 genes were functional proteins. Among these function proteins, four candidate genes, Glyma.13G109100, Glyma.03G183200, Glyma.09G102200, and Glyma.09G102300 were analyzed as significant haplotype variations, which encode MYB-related transcription factor, auxin-responsive family protein, F-box protein and CYP450, respectively. In addition, the relative expression with four candidate genes in the V030 and V071 (Among them, the plant height, pod number and fresh pod weight of V030 were lower than V071 strains) vegetable soybean were significantly different and these genes could be involved in plant growth and development via various pathways. Therefore, we proposed four genes from vegetable soybean germplasm that could be the key candidate genes for pod yield and plant height and these studies will accelerate the process of high-yield vegetable soybean breeding.

For the problem of poor accuracy of the existing multi-rate simulation methods, this paper proposes a multi rate real-time simulation method based on the Norton equivalent, compared with multi-rate simulation method based on the ideal source equivalent. After the Norton equivalence of the fast subsystem and the slow subsystem, they are obtained simultaneously at the junction nodes. In order to reduce the amount of simulation calculation, the Norton equivalent circuit is obtained by incremental calculation. The data interface between the fast subsystem and the slow subsystem is realized by extrapolation method. For ensuring the real-time performance of the simulation, the method that the slow subsystem calculates ahead of the fast subsystem is given for the slow subsystem with a large amount of calculation. Finally, the AC/DC hybrid power system was simulated on the real-time simulation platform (FRTDS), and the simulation results were compared with the single-rate simulation, which verified the correctness and accuracy of the method.

It is common knowledge that estimating the height component of GNSS stations in general is much more problematic than estimating the horizontal position. Many different effects, such as tectonic signals, non-tectonic signals, atmospheric delay, noise, etc., are known to affect the height component of GNSS stations more than the horizontal component. However, the height component of GNSS stations is still poorly estimated. In this study, the height time series of 37 continuous GNSS stations covering the 2014–2019 date range is used from the Turkish National Permanent GNSS Network-Active (TUSAGA-Active). Since it is easier to interpret the effects of the height component due to its topographic features and seasonal changes being more effective than in the rest of the country, stations were chosen in the Eastern Anatolia region of Turkey. The daily coordinates of the GNSS stations were obtained as a result of the GAMIT/GLOBK software solution. By applying time series analysis to the daily coordinate values of the stations, statistically significant trends, periodic and stochastic components of the stations were determined. As a result of the analysis, the vertical velocities of the GNSS stations and the standard deviations of the vertical velocities were determined. Furthermore, when the height components of continuous GNSS stations were examined, it was seen that there were seasonal effects, and it was investigated whether the height components were related to meteorological parameters. For that, simple linear regression analysis was performed to determine how dependent the height components of the continuous GNSS stations were on meteorological parameters. As a result of the analysis, the height components of the continuous GNSS stations are dependent on meteorological parameters such as temperature, pressure, relative humidity, wind speed, and precipitation. In addition, height component time series analysis of continuous GNSS stations was performed by using Autoregressive Moving Average (ARMA) models from linear time series methods. As a result of the study, the performance of the ARMA modeling results again indicated the dependence of the height component of the continuous GNSS stations on the meteorological parameters.

This paper proposes a novel approach, based on the adaptive rate processing and analysis, for the isolated speech recognition. The idea is to smartly combine the event-driven signal acquisition and windowing along with adaptive rate processing, analysis and classification for realizing an effective isolated speech recognition. The incoming speech signal is digitized with an event-driven A/D converter (EDADC). The output of EDADC is windowed with an activity selection process. These windows are later on resampled uniformly with an adaptive rate interpolator. The resampled windows are de-noised with an adaptive rate filter and their spectrum are computed with an adaptive resolution short time Fourier transform (ARSTFT). Later on, the magnitude, Delta and Delta-Delta spectral coefficients are extracted. The Dynamic Time Warping (DTW) technique is employed to compare these extracted features with the reference templates. The comparison outcomes are used to make the classification decision. The system functionality is tested for a case study and results are presented. An 8.2 times reduction in acquired number of samples is achieved by the devised approach as compared to the classical one. It aptitudes a significant computational gain and power consumption reduction of the proposed system over the counter classical ones. An average subject dependent isolated speech recognition accuracy of 96.8% is achieved. It shows that the proposed approach is a potential candidate for the automatic speech recognition applications like rehabilitation centers, smart call centers, smart homes, etc.

The quality of photogrammetric-based derived products like orthophotos, digital terrain models (DTMs) and digital line maps as well as the global digital elevation models (DEM) are rigorously dependent on the accuracy of image orientation. This paper evaluates the vertical accuracy of aerial photogrammetric Digital Terrain Model (DTM), Shuttle Radar Topography Mission (SRTM), Advanced Spaceborne Thermal Emission and Reflectance Radiometer (ASTER), and TerraSAR-X's twin satellite of TanDEM-X (TDX) datasets against in-situ orthometric heights computed from ellipsoidal heights and the 2008 Earth Gravitational Model (EGM2008) derived geoid heights in Ethiopia. The quality of the four global digital elevation models was also validated against the aerial photogrammetric DTM measurements. Besides, the accuracies of the photogrammetric DTM and the four DEM products were checked for their compliance to the American Society for Photogrammetry and Remote Sensing (ASPRS) standards as well as the Ethiopian national vertical data evaluation standards. The study showed that the photogrammetric DTM is in a good agreement with the reference orthometric heights compared to SRTM, ASTER and TDX datasets. More precisely, the result has an absolute accuracy of 1.67 m at Linear Error (LE) 95% confidence level, while the absolute accuracy of SRTM3 arc seconds (SRTM3) at LE 90% (11.91 m) is better than its product specification (16 m). The absolute accuracy of SRTM1 arc second (SRTM1) (7.70 m at LE 90%) surpasses that of SRTM3, whereas the absolute accuracy of ASTER DEM is somehow below its product specification. TDX also has the same vertical accuracy (10.29 m at LE 90%) compared to its product specification (10 m). Furthermore, the vertical accuracy of the photogrammetric DTM meets the100 cm vertical accuracy of the 2015 ASPRS standard. However, it does not meet the Ethiopian national vertical data accuracy requirement standard, i.e., RMSEz of ± 0.45 m. In general, the photogrammetric DTM, SRTM1, and TDX have been proven a superior product over the SRTM3 and ASTER DEMs, and better to use these products for high-level precision and accuracy required applications.

Respiratory rate is an important biomarker that indicates changes in the clinical condition of critically ill patients, so a surveillance tool that can accurately monitor the changing respiratory rate in real time is needed. Through investigating various pairs of machine learning models, we proposed new machine learning model for real-time respiratory rate estimation using photoplethysmogram. New photoplethysmogram-driven respiratory rate dataset(StMary) was collected from surgical intensive care unit of a tertiary referral hospital, using photoplethysmogram signal collector. For 50patients and 50healthy volunteers, 2-minute photoplethysmogram was collected for each subject twice. To evaluate the respiratory rate of subject, it was inputted into the deep neural network model we built, and dataset was splitted into training, validation, testing dataset, then 4-fold cross validation was exploited. Our deep neural network model trained with StMary and two public datasets(BIDMC and CapnoBase) individually, or selectively merged dataset had shown a low error rate in respiration rate measurements. Our model trained with StMary showed low mean absolute error score(1.0273±0.8965), and trained with 3 datasets(CapnoBase, BIDMC and StMary) showed a lower error rate(1.7359±1.6724) than the model trained with CapnoBase and BIDMC(1.9480±1.6751). We could verify the performance of model evaluating respiratory rate from photoplethysmogram, and our dataset could contribute as the clinical research data that supports artificial intelligence models evaluating respiratory rate and surveillance tools to test whether their monitoring function works properly.

The storm of November 12th-13th, 2019 provoked the displacements of boulders in a central Mediterranean rocky coast; with reference to a selected area, prone to the boulder production and geomorphologically monitored for years, a field-oriented study approach was applied for the phenomenon, by collating data concerning pre-storm locations and kinematics of these boulders. The number of displaced boulders is 11, that is, in terms of morphological imprint of a specific storm, one of the major study cases for the Mediterranean. In addition, based on widely used hydrodynamic equations, the minimum wave height required to displace the boulders is assessed. The values conform with the expected values for the wave climate dominating during the causative meteorological event and give a measure of the energy of the storm slamming the coast. Boulder dislodgements usually have plays a key role in determining the rate of the coastal recession, likely also in the investigated area. In view of an adverse climate evolution with a possible increase of energy and frequency of severe storms, the results deriving from the study of this morphodynamics should be considered for the hazard assessment and coastal management.

This mathematical observation deals with the development of a completely new expression [(S/4D) × √ {(S₁²-D²)(D²-D₁²)}] to calculate the area of a trapezoid system. Because of the difficulties of the previous methods to find out the area of a trapezoid (AOT), the proposed formula has thus indicated the best way to determine the AOT more precisely and easily beyond limitation, successfully. It is obvious that the derived formula is helpful to determine AOT more easily and precisely rather than existing method. And this developed theorem for the trapezoid system is observed for the first time.

By using directed dimensional analysis and data fitting, an explicit universal scaling law for the velocity of dominoes toppling motion is formulated. The scaling law shows that domino propagational velocity is linearly proportional to the 1/2 power of domino separation and thickness, and -1/2 power of domino height and gravitation. The study also proved that dominoes width and mass have no influence on the domino wave traveling velocity. The scaling law obtained in this Letter is very useful to the dominoes game and will help the domino player to place the dominoes for fast speed and have a quick estimation on the speed without doing complicated multi-bodies dynamical simulation.

Using DCC-GARCH and EGARCH model, this paper finds that since 1990, the relationship between crude oil prices and the US dollar index is time-varying, demonstrating a process of “very weak correlation—negative correlation—enhanced negative correlation—weakening negative correlation”, but the existing research does not provide enough reasonable explanation. Therefore, this paper proposed a “key mediating factors” hypothesis which points out that whether there is a common “key mediating factor” is important source of the time-varying relationship between two assets. We argue that market trend and financial market sentiment undertook the role of “key mediating factor” during the period of “2002 to the financial crisis” and “financial crisis to 2013”, while other periods lack the “key mediating factors”.

For a subject suffering from complex post-traumatic stress disorder, a psychological intervention program was designed, monitored in real-time during psychotherapy, and evaluated quantitatively and qualitatively after psychotherapy. One male subject participated in this program under consent. The proposed intervention program was designed using cognitive behavioral therapy and stabilization treatments for body-based sensory processes in four sessions of 90 min each. During psychotherapy, a wearable heart sensor and a communication application were utilized to determine the subject’s current psychological state. After the intervention, the effect of the proposed program was analyzed qualitatively and quantitatively using the Impact of Event Scale–Revised (IES-R-K), Athens insomnia scale (AIS), and heart rate variability (HRV). After the intervention program was conducted, the subject reconstructed his traumatic events and trained himself with certain psychological techniques to decrease his negative thoughts and emotions induced by his previous traumatic events. The IES-R-K and AIS ten months after the last session were changed positively by approximately 25% compared with the subject’s state before the first session. During psychotherapy, the HRV exhibited a significant correlation with the subject’s emotional state. The proposed intervention program induced a positive change in the subject. Although the HRV was well utilized in this investigation, more sophisticated statistical analysis will be required for clinical trials.

Boulder dynamics may provide essential data for the coastal evolution and hazards assessment and can be focused as a proxy for the onshore effect of intense storm waves. In this work, detailed observations of currently available satellite imagery of the Earth surface allowed to identify several coastal boulders displacements in the Southern Apulia coast (Italy), in a period between July 2018 and June 2020. Field surveys confirmed the displacements of several dozens of boulders up to several meters in size, also allowing the determination of the initial position for many of them. Archive weather analyses identified two possible causative storms during the same period, and calculations based on analytical equations are found in agreement with the displacement by storm waves for most of the observed boulders. The results help to give insights about the onshore effect of high storm waves on the coastal hydrodynamics and the possible future flooding hazard in the studied coast.

Studying the interaction between the upper ocean and the typhoons is crucial to improve our understanding of heat and momentum exchange between the ocean and the atmosphere. In recent years, the upper ocean responses to typhoons have received considerable attention. The sea surface cooling (SSC) process has been repeatedly discussed. In the present work, case studies were examined on five strong and super typhoons that occurred in 2016—LionRock, 1610; Meranti, 1614; Malakas, 1616; Megi, 1617; and Chaba 1618—to search for more evidence and new features of typhoon’s impact on the sea surface environment. The typhoon monitoring data from the Central Meteorological Observatory, the sea surface temperature (SST) data from satellite microwave and infrared remote sensing, and the sea surface height anomaly (SSHA) data from satellite altimeters were used to analyze in detail: the SSC features caused by typhoons, the relationship between the SSC and the typhoon travelling speed, and the variations in cold and warm eddies during typhoon passage. Results showed that: (1) SSC generally occurred during typhoon passage and the degree of SSC was always determined by the strength and the travelling speed of the typhoon, as well as the initial SST. (2) One day before or on the day of typhoon passage, the SSHA slightly increased due to low surface pressure. After the typhoon passed, the SSHA obviously decreased along with the SSC. The pre-existing positive SSHAs, which always represent warm eddies, decreased or disappeared during typhoon passage, whereas negative SSHAs or cold eddies were enhanced. (3) New cold eddies were generated, especially at the turning points of the typhoon path. The presence of warm eddies is suggested to have a strengthening effect on the typhoons.

The technology for determining the point’s coordinates on the earth’s surface using the global navigation satellite system (GNSS) is becoming the norm along with ground-based methods. In this case, determining coordinates does not cause any particular difficulties. However, to identify normal heights using this technology with a given accuracy, special research is required. The fact is that satellite determinations of geodetic heights (h) over an ellipsoid surface differ from ground-based measurements of normal height (HN) over a quasi-geoid surface by a certain value called quasi-geoid height or height anomaly (ζ). In relation to determining heights of a certain territory, the concept of geoid height (N) is usually operated when dealing with a geoid model. In this work, geodetic and normal heights are determined for 5 control points in three different regions in Lebanon, where measurements are carried out using GNSS technology and geometric levelling. The obtained quasi-geoid heights are compared with geoid heights derived from the global Earth model EGM2008. The results obtained showed that, in the absence of gravimetric data, the combination of global Earth model data, geometric levelling for selected areas and satellite determinations allows the creation of a high accurate altitude network for mountainous areas.

Abstract: rainfall is the main driver of soil erosion. With the daily rainfall, riverine flow discharge and sediment load in the upper Lianjiang River watershed from 1990 to 2020, extreme rainfall events were defined by the 95th percentile method and minimum event interval time (MIT), change trends and mutations of yearly rainfall, riverine flow discharge and sediment load were identified using the Mann-Kendall test, then the optimum lag response time and antecedent rainfall were investigated with the multiple linear regression. The results showed that (1) the sediment changed significantly and abruptly in 1995 due to the expansion of the garden land. (2) Compared with ordinary rainfall, extreme rainfall events explained more variations of riverine flow and sediment with a higher degree, and had a more significant effect on the lag time of runoff and sediment. (3) Garden land expansion in extreme rainfall scenarios resulted in longer lag times for runoff and sediment and decreased demand for antecedent rainfall with more pre-event time. Therefore, taking the rainfall event as a breakthrough, analyzing the antecedent rainfall and the lag response of riverine flow discharge and sediment load is conducive to revealing the response mechanism of riverine flow discharge and sediment load and improving the simulation accuracy of riverine flow and sediment under extreme rainfall condition, thus help for the soil erosion control under extreme rainfall.

Integrating photovoltaic (PV) systems plays a pivotal role in the global shift toward renewable energy, offering significant environmental benefits. In many instances, utility companies pay for both energy and peak demand. PV systems can effectively reduce energy consumption during their operational periods, while, their contribution during peak hours, particularly in the early morning and late evening, is often limited. To address this issue, battery storage systems are utilized for storing energy during off-peak hours and releasing it during peak times. However, finding the optimal size of PV-battery systems remains a challenge. This study proposes a novel statistical model to optimize PV-battery system sizing for enhanced peak demand reduction. The model aims to flatten 95% of peak demand days up to a certain demand threshold, ensuring consistent energy supply and financial benefit for utility companies. A straightforward and effective search methodology is employed to determine the optimal system sizes. Additionally, the model effectiveness is rigorously tested through a modified Monte Carlo simulation coupled with time series clustering to generate various scenarios to assess performance under different conditions. The results indicate that the optimal PV-battery system successfully flattens 95% of daily peak demand up to 2000 kW, yielding a financial benefit of $812,648 over 20 years.

COVID-19 is fast spreading around the globe in a highly contagious manner. In this article we have described that after prolonged interventions the percentage growth curve for COVID-19 cases showed a flattened nature, after prolonged volatility in number of COVID-19 cases. The stability in the growth curve was continuously maintained from 18 April, 2020 to 29 April, 2020. The significance of this sustained stable curve on survival & doubling time has been discussed. One significant part of the study reflected that the doubling time of COVID-19 cases showed a negative correlation with the percent increase in COVID-19 cases (R=0.301). It is plausible that if such negative correlation is maintained with further flattening of the growth curve at a lower level, it may influence the infective ability of nCoV-19 & ultimately have a positive evolutionary implication on the spread of COVID-19 among the population.

We present a novel passive satellite remote sensing approach for observing the three-dimensional distribution of aerosols emitted from wildfires. This method, called AEROS5P, retrieves vertical profiles of aerosol extinction from measurements of the TROPOMI satellite sensor onboard the Sentinel 5 Precursor mission. It uses a Tikhonov-Phillips regularization which iteratively fits cloud-free near-infrared and visible selected reflectances to simultaneously adjust the vertical distribution and abundance of aerosols. The information on the altitude of the aerosol layers is provided by TROPOMI measurements of the reflectance spectra at the oxygen A-band near 760 nm. In the present paper, we use this new approach for observing the daily evolution of the three-dimensional distribution of biomass burning aerosols emitted by Australian wildfires on 20-24 December 2019. Aerosol optical depths (AOD) derived by vertical integration of the aerosol extinction profiles retrieved by AEROS5P are compared with MODIS, VIIRS and AERONET coincident observations. They show a good agreement in the horizontal distribution of biomass burning aerosols, with a correlation coefficient of 0.86 and a mean absolute error of 0.2 with respect to VIIRS. A fair agreement is found between coincident transects of vertical profiles of biomass burning aerosols derived from AEROS5P and from the CALIOP spaceborne lidar. The mean altitude of these aerosols derived from these two measurements show a good agreement, with a small mean bias (185 m) and a correlation coefficient of 0.83. Moreover, AEROS5P observations reveal the height of injection of the biomass burning aerosols in 3D. The highest injection heights during the period of analysis are coincident with the largest fire radiative power derived from MODIS. Consistency is also found with respect to the vertical stability of the atmosphere.

Full waveform (FW) LiDAR holds great potential for retrieving vegetation structure parameters at a high level of detail, but this prospect is constrained by practical factors such as lack of available handy processing tools and technical intricacy of waveform processing. This study introduces a new product, named the Hyper Point Cloud (HPC) derived from FW LiDAR data, and explore its potential applications such as tree crown delineation using the HPC-based intensity and percentile height (PH) surfaces, which show a promising solution to the constraints of using FW LiDAR data. Results of the HPC present a new direction to handle FW LiDAR data and offer prospects for studying the mid-story and understory of vegetation with high point density (~ 182 points/m2). The intensity-derived digital surface model (DSM) generated from the HPC shows that the ground region has larger maximum intensity (MAXI) and mean intensity (MI) than the vegetation region while having smaller total intensity (TI) and number of intensities (NI) at the given grid cell. Our analysis of intensity distribution contours at individual tree level exhibit similar patterns, indicating that the MAXI and MI are decreasing from the tree crown center to tree boundary while a rising trend is observed for TI and NI. These intensity variable contours provide a theoretical justification for using HPC-based intensity surfaces to segment tree crowns and exploit their potential for extracting tree attributes. The HPC-based intensity surfaces and the HPC-based PH Canopy Height Models (CHM) demonstrate promising tree segmentation results comparable to the LiDAR derived CHM for estimating tree attributes such as tree locations, crown widths and tree heights. We envision that products such as the HPC and the HPC-based intensity and height surfaces introduced in this study can open new perspectives to use FW LiDAR data and alleviate the technical barrier of exploring FW LiDAR data for detailed vegetation structure characterization.

Milling machines have made denture fabrication possible with high accuracy in a short time. However, the relationship between the milling conditions, accuracy, and milling duration has not been clarified. This study aimed to clarify the effects of milling conditions on surface roughness and milling duration. The specimen was designed using a CAD software, and milled using PMMA disks. In milling, the parameters of finishing the specimen surface were adjusted. Three different spindle speeds and four different feed rates were set. Twelve combinations of each parameter were used for milling, and the surface roughness and milling duration were measured. Results showed that the surface roughness significantly increased with the feed rate on the slopes of the specimen. The surface roughness differed with the spindle speed on the left and right slopes. The spindle speed and feed rate did not affect the surface roughness on the flat surface. The milling duration was not affected by spindle speed but decreased as the feed rate increased. In conclusion, by increasing both the spindle speed and feed rate, the milling duration could be shortened while maintaining a constant surface quality. The optimum milling conditions were a spindle speed of 40,000 rpm and feed rate of 3,500 mm/min.

Plant height is one of the key agronomic traits for improving the yield of sweetpotato. The phytohormones, especially gibberellins (GAs) are crucial to regulate plant height. The 9-cis-epoxycarotenoid dioxygenase (NCED) is the key enzyme for abscisic acid (ABA) biosynthesis signalling in higher plants. However, its role in regulating plant height has not been reported to date. Here, we cloned a NCED gene, IbNCED1, from sweetpotato cultivar Jishu26. This gene encoded the 587-amino acid polypeptide containing an NCED superfamily domain. The expression level of IbNCED1 was highest in the old tissues in the field-grown Jishu26. The expression of IbNCED1 was induced by ABA and GA. Overexpression of IbNCED1 promoted the accumulation of ABA and inhibited the content of active GA3 and plant height, and affected the expression levels of genes involved in the GA metabolic pathway. IbNCED1 overexpression reduced sensitivity to GA3 and exogenous application of GA3 could rescue the dwarf phenotype. In conclusion, we suggest that IbNCED1 regulates plant height and development by controlling the accumulation of active GA3 signalling pathway in transgenic sweetpotato.

Background Children often suffer the nonspecific musculosceletal pain as reported in literature. Aim To determine relationship between body weights with development of musculoskeletal pain and to determine whether growing in body height is associated with musculoskeletal pain in schoolchildren. Subjects/ Methods A prospective longitudinal study included 1315 school children aged 7-14 years (652 boys and 663 girls) and was performed in 13 elementary schools in B&H. Child body height and body weight were measured. The survey of perception of musculoskeletal pain in different body regions of subjects was conducted by adjusted Nordic Musculosceletal Questionnaire (NMQ). Results The highest prevalence of an overweight and obesity in the 10th year 35.7% and the lowest frequency 17.8% in the 14th year was. In the age 14th obesity was’nt found. Boys have more prevalence of overweight. Using logistic regression model, we found that school children with normal BMI were protected with increased body height of acute lower back pain (β= -0.089, 95%CI, -9.730- -0.023, P< 0.049), and increased body height was protector of obese school children of acute upper back pain (β= -0.356, 95%CI, -14.077- -3.878, P< 0.001) and chronic lower back pain (β= -0.356, 95%CI, -14.077- -3.878, P< 0.001). Conclusion Schoolchildren with normal weight more often have had musculosceletal pain than those with overweight or obesity. This can be associated with intense physical growth period in height, especially. The assumption is that the increase in height changes the relationship between excessive BMI and musculoskeletal pain in children of school age.

The aims of the study were to evaluate seedling growth and survival of Prunus africana provenances in awi highland based on ecological requirement of the tree. We measured survival and growth of three P.africana provenances seedlings found in Ethiopia (provenances sources namely: Gedeo, Jibat and Munnessa). Design of experiment with randomized complete block design (RCBD) with three replications. Seedlings planted at 2m, 2.5m and 3m distance between plants, plot, and blocks respectively. A plot size of 10mx10m and 25 plants are found per plot (0.01ha). We used ANOVA to test differences in survival, and growth among provenances over time. Results concluded that, provenances have no significant variation among in establishment rate, plant height and collar diameter growth. Of these provenances, Jibat was the first in establishment (56%), second in height (1.97m) and diameter (2.89cm). Gedeo was stood first in height (2.30m) but second in establishment rate (52%) and thickness(3.45cm), but Munessa with very good growth in diameter(3.59cm) might be prefreed for bark extraction followed by Gedeo, last in height (1.75m),but established second (52%). Contrary to expectations, seedlings were still at substantial risk of mortality ≥3 years after planting. Probably the plants survival rate and growth probably affected by altitude, soil water potential, light exposure, and wild animal presence in the surrounding. In steep slope sites, canopy shade, existing weed vegetation as well as wild animals such as apes is unlikely to enhance seedling survival after planting. Our results suggest that seedling mean growth increased with 0.008mm thickness and 0.41mm per day while 2.8mm thickness and 146.8mm tall increment recorded in 2560meter elevated high land or injibara with mean value of 18.5°C and rain fall is 1300mm.

We propose a novel tensor-based formalism for inferring causal structures from time series. An information theoretical analysis of transfer entropy (TE), shows that TE results from transmission of information over a set of communication channels. Tensors are the mathematical equivalents of these multi-channel causal channels. A multi-channel causal channel is a generalization of a discrete memoryless channel (DMC). We consider a DMC as a single-channel causal channel. Investigation of a system comprising three variables shows that in our formalism, bivariate analysis suffices to differentiate between direct and indirect relations. For this to be true, we have to combine the output of multi-channel causal channels with the output of single-channel causal channels. We can understand this result when we consider the role of noise. Subsequent transmission of information over noisy channels can never result in less noisy transmission overall. This implies that a Data Processing Inequality (DPI) exists for transfer entropy.

The longleaf pine (Pinus palustris P. Mill.) forest type occupied a much greater area in the United States prior to the arrival of Europeans, estimated to be around 37.2 million hectares. This area has been greatly reduced, and these ecosystems now occupy only about 1.2 to 1.6 million hectares. However, there has been great interest in the restoration of this forest type, and existing stands are actively managed. Thus, managers need tools to estimate site quality and ultimately productivity. Here, 16 existing equations to estimate site index and dominant height in naturally regenerated longleaf pine stands are examined for their behavior across a range of site quality and age conditions. Others can use this information as a reference to determine which equation may be best for their situation.

Falls at height are among the major causes of fatal accidents at work, especially in the construction sector. Maintaining balance while performing a tool with both hands generates physical efforts and mental loading that needs to be managed for workers’ safety and health. The purpose of the study is to compare perceived (dis)comfort (overall and localized), the ergonomic risk and the perceived effort through the acquired postures that subjects assumed during the execution of simple and common tasks both on a ladder and on the ground. 26 subjects were asked to perform four tasks in both conditions: top screwing, frontal screwing, object picking from the bottom forward, and object picking from the bottom sideways. Subjective and objective data were gathered for assessing subjective experience (discomfort and effort, perceived) and ergonomic risk. Results highlighted few ergonomic risk differences among “on ladder” and “on ground” tasks, while subjective data reveal significant differences in different scenarios. Main results regard knees and neck areas as the most critical ones.

Adaptations to climate change rely on understanding the dynamics of plant biomass stocks on the planet. The high levels of deforestation in Cerrado have transformed this biome into the second-largest Brazilian source of carbon emissions. The objective of this study was to develop a method to accurately estimate aboveground and total biomass values among shrublands, savannas, and forests located in the Cerrado biome, using an allometric equation adjusted from canopy height, obtained through optical and laser sensors. The results show similarity between the estimates employed by our method and the data found in the literature review for different phytophysiognomies in the Cerrado biome. Shrubland formations showed higher biomass estimation uncertainties due to the discontinuity of isolated trees and the lower canopy height when compared to more clustered tree canopies in savannas and taller canopies in forests. Aboveground biomass estimates were related to expansion factors, and specific maps were developed for each compartment by root, litter, and necromass. The sum of these compartments is presented in the aboveground and below forest biomass map. This study presents, for the first time, the mapping of total biomass in 10 m pixels of all regions of the Cerrado biome.

Hypersonic aircraft focuses more on the integration of aircraft and engine than ordinary aircraft owing to high performance requirements, and the nozzle design is reflected in the required large area ratio of nozzle inlet and outlet and the compactness of the overall size of the aircraft. In this study, the height constraint is directly introduced into the maximum thrust nozzle design method. A new method for designing nozzles under the height constraints that consults the maximum thrust theory is proposed. Initially, the condition that the nozzle reaches the maximum thrust under the height constraint is deduced mathematically. Then, a nozzle design method satisfying the height constraint is computed using the method of characteristics (MOC). Subsequently, the influence of the design parameters on the design method is studied parametrically. Results show that Mach number scale and asymmetrical factors can affect ramp length and flap length of the nozzle, respectively. These factors great influence the axial thrust performance and lift under a specific height constraint. Compared with the traditional truncation design method, the thrust coefficient and lift increased by 11.93% and 138.45% respectively.

The aim of this article was to examine if there are position-specific differences in the morphological characteristics of sub-elite female football players and to establish normative standards for this level of female football players. The morphological features of 101 sub-elite female football players (age: 21.8±2.7 years) were assessed. Twenty anthropometric sites were used in the measurements of body composition and somatotype. The average value of body fat percentage was 20.8±5.7%. The somatotype of the overall group was 4.0–2.4–2.1. Positional significant (p ≤ 0.05) differences were found between goalkeepers and outfield players in morphological characteristics. Goalkeepers were taller, heavier, possessed the highest body fat percentage and showed higher values for all skinfolds, breadth, girth and length measurements. However, there were very few practically worthwhile differences between the outfield positions. Positional groups did not differ (p ≤ 0.05) in somatotype characteristics either. The study suggests that at sub-elite level there are mainly differences between goalkeepers and outfield players, but outfield players are homogeneous when comparing morphological characteristics. These results may serve as normative values for future comparisons regarding the morphological characteristics of female football players.

Abstract In order to reduce the failure accidents of conventional packers, a kind of sealing structure of retrievable packers is designed, which can provide reference for optimizing the sealing performance and pressure capacity of packers. And theoretical calculation and experimental research on its sealing performance and pressure capacity are carries out through the finite element analysis on the contact with large deformation based on Abaqus and experimental. The results show that when the rubber cylinder of retrievable packers in the sealing process, the upper packer is subjected to greater stress and mainly plays a sealing role. In order to improve the sealing performance of packer, the height of upper and lower packer should be preferentially selected about 60 mm, the height of middle rubber cylinders should be about 50 mm, and the thickness of packer should be about 21 mm. The newly designed rubber cylinders can meet 150 ℃. Sealing and pressure-bearing function under the condition of 10000 Psi. The rubber cylinder of newly designed can satisfy the function of sealing and pressure-bearing under 140 ℃ and 10000 Psi. The whole experiment shows that the capacity of bearing pressure and sealing is stable, which can better meet the requirements of field use.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

The thermoelectric generator (TEG) stands out in many energy harvesters due to its simple structure, small size, etc. However, previous studies rarely probe into the influence of TEG internal resistances on extracting maximum power from TEG, and tracking efficiency is limited. By analyzing the relationship between the tracking efficiency and the TEG internal resistances, a time exponential rate perturbation and observation (P&amp;O) technology is proposed to achieve maximum power point tracking (MPPT) for a wide resistance range of TEG. Using the time exponential rate P&amp;O, the MPPT circuit observes the power change by comparing PMOS on-time and perturbs the power by adjusting NMOS on-time exponentially. The MPPT circuit is implemented in a 110nm CMOS process. The tracking efficiency keeps a high level from 98.9 to 99.5%. The applicable range of the TEG resistance is from 1 to 12Ω, which is enhanced at least 2.2 times.

We present a near real-time solution for 3D reconstruction from aerial images captured by consumer UAVs. Our core idea is to simplify the multi-view stereo problem into a series of two-view stereo matching problems. Our method applies to UAVs equipped with only one camera and does not require special stereo-capturing setups. We found that the neighboring two video frames taken by UAVs flying at a mid-to-high cruising altitude can be approximated as left and right views from a virtual stereo camera. Leveraging GPU-accelerated real-time stereo estimation, efficient PnP correspondence solving algorithms and extended Kalman filter, our system simultaneously predicts scene geometry and camera position/orientation from the virtual stereo cameras. Also, this method allows user selection of varying baseline lengths, which provides more flexibility given the trade-off between camera resolution, effective measuring distance, flight altitude, and mapping accuracy. Our method outputs dense point clouds at a constant speed of 25 frames per second and is validated on a variety of real-world datasets with satisfactory results.

Quantum effects arising from manifestly broken time-reversal symmetry are investigated using time-dependent perturbation theory in a simple model. The forward time and the backward time Hamiltonians are taken to be different and hence the forward and backward amplitudes become unsymmetrical and are not complex conjugates of each other. The effects vanish when the symmetry breaking term is absent and ordinary quantum mechanical results such as Fermi Golden rule are recovered.

The planetary boundary layer height (PBLH) is one of the key factors in influencing the dispersion of the air pollutants in the troposphere and hence the air pollutant concentration on ground level. For this reason, accurate air pollutant concentration depends on the performance of PBLH prediction. Recently, ceilometer, a lidar instrument to measure cloud base height, has been used by atmospheric scientists and air pollution control authorities to determine the mixing level height (MLH) in improving forecasting and understanding the evolution of aerosol layers above ground at a site. In this study, ceilometer data at an urban (Lidcombe) and a rural (Merriwa) location in the New South Wales, Australia was used to validate the PBLH prediction from two air quality models (CCAM-CTM and WRF-CMAQ) as well as to understand the aerosol transport from sources to receptor point at Merriwa for the three case studies where high PM10 concentration was detected in each of the three days. The results show that the PBLH prediction by the two air quality models corresponds reasonably well with observed ceilometer data and the cause and source of high PM10 concentration at Merriwa can be found by using ceilometer MLH data to corroborate with back trajectory analysis of transport of aerosols to the receptor point at Merriwa. Of the three case studies, one had aerosol source from north and north west of Merriwa in remote NSW where windblown dust is the main source, and the other two had sources from south and south east of Merriwa where anthropogenic sources dominate,

Nowadays, wearable devices for human health monitoring are increasingly become popular and widely used. Typically, the wearable device is small size and operates with batteries. Therefore, the wearable device acquires bio-signals and transfers to smartphones or personal computers (PC) via WiFi/ Bluetooth for processing data. To reduce power consumption is one of the most important challenges of designing wearable devices. To solve this problem, the proposed signal quality valuation (SQV) method can be select the high-quality signal and reduce the transfer time to other devices. In this paper, the proposed SQV and data compression method rely on real-time PPG signals analysis to retain important information of PPG signal, improve performance and power consumption of PPG devices. Besides, we also proposed Heuristic rules for heart rate (HR) estimation with compression data. The experimental results show that the highest compression ratio (CR) is 387.8 with BIDMC Physionet database (sampling frequencies of 125 Hz) and HR error as 1.43 bpm for averaging absolute error (avAE), the standard deviation absolute error (sdAE as 0.4) and relative error mean (avRE as 0.019). The proposed real-time PPG measurement system (sampling frequency as 100/ 200/ 400 Hz) reduce power consumption and open the new structure for healthcare application systems

We utilize how Weber in 1961 initiated the process of quantization of early universe fields to the problem of what may be emitted at the mouth of a wormhole. While the wormhole models are well developed, there is as of yet no consensus as to how, say GW or other signals from a wormhole mouth could be quantized, or made to be in adherence to a procedure Weber cribbed from Feynman, in 1961. In addition, we utilize an approximation for the Hubble parameter parameterized from Temperature using Sarkar’s H ~ Temperature relations, as given in the text . Finally after doing this we go to the Energy as E also ~ Temperature, and from there use E (energy) as ~ signal frequency. This gives us an idea of how to estimate frequency generated at the mouth of a wormhole.

Poplars (Populus spp.) are of significant ecological and economic importance. Long-term breeding efforts were aimed mainly at obtaining fast-growing and productive plants and less considered resistance to pests. This study aimed to identify the patterns of susceptibility to Saperda carcharias (Linnaeus, 1758) (Coleoptera: Cerambycidae) among Populus hybrids and pure species, considering crossing combinations and some other traits. In our research, 35 clones of poplar species and hybrids of the Ukrainian and foreign selection from the Aigeiros, Tacamahaca, and Leucoides sections were tested in 2021 and 2023 in the plantation created in 2014 in Eastern Ukraine. S. carcharias preferred infesting clones with earlier foliage development, larger diameters, and height increments. Specifically, hybrids with American maternal lineage showed the highest susceptibility, whereas those with European maternal lineage or Asian origin displayed lower infestation levels or resistance, respectively. This variability suggests a complex relationship between genetic background and pest resistance, underlining the need for a deeper understanding of the factors influencing susceptibility to S. carcharias. Selecting native species clones or creating mixed clone plantations could enhance the resilience of poplar plantations to pest threats.

A pilot study regarding the transplantation of 100 specimens of the critically endangered Pinna nobilis took place in summer of 2019 in Maliakos Gulf (Central Aegean, Greece). In this study we present the relationships between total height (HT, in cm), unburied length (UL, in cm), and shell width (SW, in cm) for P. nobilis and the relationship between HT and net weight (W, in g). Length-length relationships were all linear for all cases: r2 > 0.900), whereas the relationship between HT and W was exponential with the value of the exponent b being allometric. "Ecology, Conservation and Restoration of Threatened Animal"

Plant height is significantly correlated with grain traits, which is a component of wheat yield. The purpose of this study is to investigate the main QTLs that control plant height and grain-related traits in multiple environments. In this study, we constructed a high-density genetic linkage map using the Wheat50K SNP Array to map quantitative trait loci (QTLs) for these traits in 198 recombinant inbred lines (RILs). The two ends of the chromosome were identified as re-combination-rich areas in all chromosomes except chromosome 1B. The middle area of the chro-mosomes was identified as the recombination-barren area. Both the genetic map and the physical map showed a significant correlation when p=0.001, with a correlation coefficient between 0.63 and 0.99. However, there was almost no recombination between 1RS and 1BS. In terms of plant height, 1RS contributed to the reduction of plant height by 3.43cm. In terms of grain length, 1RS contributed to the elongation of grain by 0.11mm. A total of 43 QTLs were identified, including 8 QTLs for Plant height(PH), 11 QTLs thousand grain weight(TGW), 15 QTLs for grain length(GL),and 9 QTLs for grain width(GW), which explained 1.36%–33.08% of the phenotypic variation. Seven were environment-stable QTLs, including two loci Qph.nwafu-4B and Qph.nwafu-4D that determined plant height. The explanation rates of phenotypic variation were 7.39%-12.26% and 20.11%-27.08%, respectively. One QTL, Qtgw.nwafu-4B, which influenced TGW, showed an explanation rate of 3.43%-6.85% for phenotypic variation, two co-segregating KASP markers were developed, the physical locations corresponding to KASP_AX-109316968 and KASP_AX-109519968 were 25.888344 MB and 25.847691 MB. Another QTL, Qgw.nwafu-4D, which determined grain width, had an explanation rate of 3.43%-6.85%. Three loci that affected the grain length were Qgl.nwafu-5A, Qgl.nwafu-5D.2 and Qgl.nwafu-6B, illustrating the explana-tion rates of phenotypic variation as 6.72%-9.59%, 5.62%-7.75%, and 6.68%-10.73%, respectively. Two QTL clusters were identified on chromosomes 4B and 4D.

All the arguments of a wavefunction are defined at the same instant implying a notion of simultaneity. In a somewhat related matter, certain phenomena in quantum mechanics seem to have non-local causal relations. Both concepts are in contradiction with special relativity. We propose to define the wavefunction with respect to the invariant proper time of special relativity instead of standard time. Moreover, we shall adopt the original idea of Schrodinger suggesting that the wavefunction represents an ontological cloud-like object that we shall call ‘individual fabric’ that has a finite density amplitude vanishing at infinity. Consequently, measurement can be assimilated to a confining potential that triggers an inherent non-local mechanism within the individual fabric. It is formalised by multiplying the wavefunction with a localising gaussian as in the GRW theory but in a deterministic manner.

Metasurfaces of gold (Au) nanoparticles on a SiO2-Si substrate were fabricated for the enhancement of second harmonic generation (SHG) using electron beam lithography and lift-off. Triangular Au nanoprisms which are non-centro-symmetric and support the second- order non-linearity were examined for SHG. The thickness of the SiO2 spacer is shown to be an efficient parameter to spectrally tune to maximise SHG. Electrical field enhancement at the fundamental wavelength was shown to define the intensity of the second harmonics. Numerical modeling of light enhancement was verified by experimental measurements of SHG and reflectivity spectra at the normal incidence. At the plasmonic resonance, SHG is enhanced up to ∼3.5×103 times for the optimised conditions.

Photoplethysmography is a widely used technique to noninvasively assess heart rate, blood pressure, and oxygen saturation. This technique has a large potential for further applications, for example in the field of physiological and mental health monitoring. However, advanced applications of photoplethysmography have been hampered by the lack of accurate and reliable methods to analyze the characteristics of the complex nonlinear dynamics of the photoplethysmogram. Methods of nonlinear time series analysis may be used to estimate the dynamical characteristics of the photoplethysmogram but they are highly influenced by the length of the time series, which is often limited in practical photoplethysmography applications. The aim of this study was to evaluate the error in the estimation of the dynamical characteristics of the photoplethysmogram associated to the limited length of the time series. The dynamical properties were evaluated using recurrence quantification analysis, and the estimation error was computed as a function of the length of the time series. Results demonstrated that properties such as de-terminism and entropy can be estimated with an error lower than 1% even for short photople-thysmogram recordings. Additionally, the lower limit for the time series length to estimate the average prediction time was computed.

An outbreak of winter disease, complicated by severe respiratory syndrome, occurred in January 2020 in a high production dairy cow herd located in a hilly area of the Calabria region. Of the 52 animals belonging to the farm, 5 (9.6%) died with severe respiratory distress, death occurring 3-4 days after the appearance of the respiratory signs (caught and gasping breath). Microbiological analysis revealed absence of pathogenic bacteria whilst Real-time PCR identified the presence of RNA from Bovine Coronavirus (BCoV) in several organs: lungs, small intestine (jejunum), mediastinal lymph nodes, liver and placenta. Since being the only pathogen identified, BCoV was hypothesized to be the cause of the lethal pulmonary infection. Like the other CoVs, BCoV is able to cause different syndromes. Its role in calfhood diarrhoea and in mild respiratory disease is well known: we report instead the involvement of this virus in a severe and fatal respiratory disorder, with symptoms and disease evolution resembling that of Severe Acute Respiratory Syndromes (SARS).

About a decade ago, active optical crop canopy sensors are being used to manage in-season variable nitrogen (N) fertilization in cornfields to match the plant demand that occurs mid season, increasing the efficiency compared to broadcast N applications. There were also initiatives of using ultrasonic sensors to measure plant height on-the-go for N application and crop water demand estimation, but no studies have integrated the optical, ultrasonic and canopy temperature for crop water stress assessment. The objective of this chapter is to evaluate the crop water status using infrared thermometry integrated with optical and ultrasonic sensors. Specifics objectives are: (i) evaluate the corn canopy temperature under different previous crop, N rates and irrigation levels; (ii) test a procedure for water stress assessment in commercial cornfields using the integration of sensors, (iii) correlate plant based sensor measurements (N status, plant height and canopy temperature) with grain yield, soil attributes and detailed topographical features, and (iv) study the spatial dependence of canopy temperature. This study was conducted in one small plot study area and on three producer’s fields in 2010. The small plot experiment consisted of two irrigation levels (70 and 100% of evapotranspiration – ET), two previous crop schemes (corn after corn – CC and corn after soybeans – CS), and four N rates (0, 75, 150, 225 kg N ha^-1). Canopy temperature, optical reflectance and plant height was measured from R2 until R6 in the small plots. At the producer’s fields, three long strips across center pivots were used to have a non-limited N and water crop and then continuous georeferenced sensors measurements were taken during side-dress (V11 growth stage) in about 10 hectares in each field. In the small plot study the crop canopy temperature was influenced by the irrigation levels and N rates. The procedure proposed could be used to identify zones in the producer’s field where water stress can be a yield limiting factor other than N derived. Inside the zones considered that water stress played a major whole, there were low correlations between plant height, plant N status and canopy temperature, indicating that the canopy temperature had more influence from water stress than vegetation cover. Concave and lower elevation areas had higher yields compared to convex and high elevation, showing that the detailed elevation mapping can be beneficial to delineate stables zones that possibly could be used in variable irrigation systems. The spatial dependence of canopy temperature was over 65 meters across producers’ sites, showing that the commercial high clearance applicator’s swath width was adequate to obtain accurate maps. The integration of plant N status, plant height and canopy temperature was beneficial to detect water stressed zones in the field. Opportunities can be foresee also for on-the-go N fertilization using integration of these sensors because is likely that water stress can be confounded with different N supply during the growing season and in different zones in the field.

Today massive amounts of sequenced metagenomic and -transcriptomic data from different ecological niches and environmental locations are available. Scientific progress depends critically on methods that allow extracting useful information from the various types of sequence data. Here, we will first discuss types of information contained in the various flavours of biological sequence data, and how this information can be interpreted to increase our scientific knowledge and understanding. We argue that a mechanistic understanding is required to consistently interpret experimental observations, and that this understanding is greatly facilitated by the generation and analysis of dynamic mathematical models. We conclude that, in order to construct mathematical models and to test mechanistic hypotheses, time-series data is of critical importance. We review diverse techniques to analyse time-series data and discuss various approaches by which time-series of biological sequence data was successfully used to derive and test mechanistic hypotheses. Analysing the bottlenecks of current strategies in the extraction of knowledge and understanding from data, we conclude that combined experimental and theoretical efforts should be implemented as early as possible during the planning phase of individual experiments and scientific research projects.

To embrace the special theory of relativity with classical thermodynamics correct Lorentz transformations of thermodynamic state functions are formulated. All of these Lorentz transformations of state functions equally support the time dilation phenomenon which is experimentally verified fact. Relativistic Boltzmann constant proves entropy to be the Lorentz variant. Twin paradox thought experiments for heat engines prove heat flux to be Lorentz variant. Lorentz transformation of entropy and heat flux proves temperature Lorentz invariant. All thermodynamic state functions are proved to be Lorentz variant which is shown in accord with Lorentz transformation of thermodynamic work.

Recently in various theoretical works, path-breaking progress has been made in recovering the well-known Page Curve of an evaporating black hole with Quantum Extremal Islands, proposed to solve the long-standing black hole information loss problem related to the unitarity issue. Motivated by this concept, in this paper, we study cosmological circuit complexity in the presence (or absence) of Quantum Extremal Islands in negative (or positive) Cosmological Constant with radiation in the background of Friedmann-Lemaî tre-Robertson-Walker (FLRW) space-time. Without using any explicit details of any gravity model, we study the behaviour of the circuit complexity function with respect to the dynamical cosmological solution for the scale factors for the above mentioned two situations in FLRW space-time using squeezed state formalism. By studying the cosmological circuit complexity, Out-of-Time Ordered Correlators, and entanglement entropy of the modes of the squeezed state, in different parameter space, we conclude the non-universality of these measures. Their remarkably different features in the different parameter space suggests their dependence on the parameters of the model under consideration.

The G2 gas cloud motion data and the scarcity of observations on the event horizon-scale distances have challenged the comprehensiveness of the central supermassive black hole model. In addition, the Planck Legacy 2018 release has preferred a positively curved early Universe with a confidence level higher than 99%. This study investigates the impact of the background curvature and its evolution over the conformal time on the formation and morphological evolution of central compact objects and the consequent effect on their host galaxies. The formation of a galaxy from the collapse of a supermassive gas cloud in the early Universe is modeled based on interaction field equations as a 4D relativistic cloud-world that flows and spins through a 4D conformal bulk of a primordial positive curvature considering the preference of the Planck release. Owing to the curved background, this scenario of galaxy formation reveals that the core of the galaxy undergoes a forced vortex formation with a central event horizon leading to opposite vortices (traversable wormholes) that spatially shrink while evolving in the conformal time. It indicates that the galaxy and its core are formed in the same process whereas the surrounding gas clouds form the spiral arms due to the frame-dragging induced by the fast-rotating core. It demonstrates that the accretion flow onto the central supermassive compact object only occurs at the central event horizon of the two opposite vortices while their other ends eject the relativistic jets. This can elucidate the relativistic jet formation and explain the G2 gas cloud motion if its orbit is around one of the vortices but at a distance from the central event horizon. The gravitational potential of the early curved bulk could contribute to galaxy formation while the present spatial flatness deprives the potential of bulk which could lead to galaxy quenching. The formation of a galaxy and its core simultaneously could explain the growth of the supermassive compact galaxy core to a mass of ~10⁹ M_⊙ at just 6% of the current Universe age.

An idea expressed in the paper [Entropy 2017, 19, 345] about the deductive formulation of a physical theory resting on explicitly- and universally-introduced basic concepts is developed. An entropic measure of time with a number of properties leading to an analog of the Galilei–Einstein relativity principle is considered. Using the introduced measure and a simple model, a kinematic law relating the size, time, and number of particles of a system is obtained. Corollaries of this law are examined. In particular, accelerated increase of the system size and, if the system size remains unchanged, decrease of the number of particles are found. An interesting corollary is the emergence of repulsive and attractive forces inversely proportional to the square of the system size for relatively dense systems and constant for sufficiently rarefied systems.

The relationship between economic growth, growth volatility and financial sector development continues to attract attention in the theoretical and empirical literature. Over time, some studies hypothesize that finance has a causal linear relationship with growth. Recently several other authors contradict this claim and argue that the relationship that exists between finance and growth is nonlinear. We investigate these claims for Nigeria for the period between 1970 and 2015, using semi-parametric econometric methods, Hansen sample splitting techniques and threshold estimator. We observed no evidence of ‘Too much finance’ as claimed by many researchers in recent times. We show that the relationship between financial development and economic growth is U-shaped. This is equally true for the relationship between financial development and growth volatility. We also discuss policy implications of our findings and recommend financial innovations and decentralization of stock exchanges to boost access to financial services, in addition, improved regulation to enhance financial market efficiency.

This work focuses on analyzing acoustic emission (AE) signals as a means to predict failure in structures. Two main approaches are considered: (i) long-range correlation analysis using both the Hurst (H) and the Detrended Fluctuation Analysis (DFA) exponents, and (ii) natural time domain (NT) analysis. These methodologies are applied to the data collected from two application examples: a glass fiber reinforced polymeric plate and a spaghetti bridge model, where both structures were subjected to increasing loads until collapse. A traditional (AE) signal analysis is also performed to reference the study of the other methods. Results indicate that the proposed methods yield a reliable indication of failure in the studied structures.

A model of space-time is presented, whose origin is set before the appearance of any universe. It uses concepts of previous work, a central one being that the information about the laws of nature is stored locally everywhere in space such that all physical processes obey them. Since information storage is bound to matter or energy, space is assumed to consist of dark energy (DE), which thus assumes an importance far beyond its function as a stopgap for an energy deficit in our universe (U). The primordial state (PS) is a timeless and relatively large space of 3 dimensions described by a Wheeler DeWitt (WDW) equation, whose solution is interpreted as an arrangement of very many space quanta and possesses all the characteristics of the time-honored concept of the unmoved mover. The comparison of WDW solutions belonging to different mass densities of the DE favors one in which the space quanta are mini black holes, and allows the space quanta to be imagined as mass points that are kept at a distance compatible with the quantum volume by the Pauli principle or something equivalent. Triggered by an increase in probability, the PS is followed by a time-dependent state of space expansion (ES). The concomitant emergence of time occurs in a lightning huge crash, consuming almost all DE of the PS. The subsequent expansion proceeds in quantum leaps, whose huge size emerges from a WDW equation novelly derived from the time-dependent classical expansion solution, and is also used as size of the PS. Information is assumed to be geometrically stored in arrangements of space quanta similar to how genetic information is stored in DNA molecules. During space expansion information must be transferred from already existing "information quanta" to new ones. This requires time, slows down the expansion and is taken into account by a friction term in the cosmological momentum equation. Sinc e the Friedmann-Lemaître (FL) equation remains fully valid, the model can exclusively be based on recognized equations, so that the assumptions used to build it can be understood as interpretations.

Reducing sedentary behaviours can help prevent non-communicable diseases, particularly among young adolescents with long term illnesses or disabilities (LTID). Much of young people’s voluntary sedentary time is related to screen-time behaviours (STBs) such as TV viewing, playing computer games, and using the computer for other activities. Although public health data on adolescents’ STB is growing, information about adolescents with LTID is currently lacking in a European context. The purpose of this study is to compare time on STBs between adolescents with and without LTID in European Countries through the HBSC 2013/14 study. Young adolescents (n = 61,329; boys 47.8%) from 15 European countries reported the time spent on TV viewing, playing computer games, and using the computer for other purposes on weekdays and the weekend. STBs were dichotomised based on international recommendations of less than 2 h per day, and Chi-square tests of independence were performed to investigate differences. STB time was combined to produce a sum score as dependent variable in multiple analysis of covariance with age and family affluence as covariates. There were statistically significant differences in computer gaming among boys and other computer use among girls for both weekdays and weekends, whereby adolescents with LTID reported higher use. In addition, both boys and girls with LTID spent more time on STBs than their same sex peers without LTID (Boys, F = 28.17, p < 0.001; Girls, F = 9.60, p = 0.002). The results of this study indicate a need for preventive strategies to address high levels of STB among young adolescents with LTID and reduce the risk of poor health outcomes associated with higher levels of sedentary behaviour.

To avoid loss of information and incorrect ranking, this paper proposes a method for ranking generalized fuzzy numbers, which guarantees both horizontal and vertical values are important parameters affecting the final ranking score. In this method, the normalized height coefficient is introduced to evaluate the influence of the height of fuzzy numbers on the final ranking score. The higher the normalized height coefficient of a fuzzy number is, the higher its ranking. The left area and the right area are presented to calculate the impact of vertical value on the final ranking score. The left area is considered the benefit area. The right area is considered the cost area. The fuzzy number is preferred if the benefit area is larger and the cost area is smaller. The proposed method can be employed to rank both normal and non-normal fuzzy numbers without normalization or height minimization. Numerical examples and comparison with other methods highlight the feasibility and robustness of the proposed method, which can overcome the shortcomings of some existing methods and can support decision-makers to select the best alternative.

Rice canopy height and density are directly usable crop phenotypic traits for the direct estimation of crop biomass. Therefore, it is crucial to rapidly and accurately estimate rice canopy phenotypic parameters. To achieve non-destructive detection and estimation of essential phenotypic parameters in rice, a platform based on LiDAR point cloud data for rice phenotypic parameter detection was established. Data collection of rice canopy layers was performed across multiple plots. The LiDAR-detected canopy top point clouds were selected using a method based on the highest percentile, and the rice canopy surface model was calculated. Canopy height estimation was the difference between ground elevation and percentile value. To determine the optimal percentile defining the rice canopy top, testing was conducted incrementally from 0.8 to 1 with an increment of 0.005. The optimal percentile value was found to be 0.975. The root mean square error (RMSE) between LiDAR-detected canopy height and manually measured canopy height was calculated. The prediction model based on canopy height (R2=0.941, RMSE=0.019) exhibited a strong correlation with actual canopy height. Linear regression analysis was conducted between gap fraction of different plots and manually detected average Leaf Area Index (LAI) of rice canopy. Prediction models for canopy LAI based on ground return counts (R2=0.24, RMSE=0.1) and ground return intensity (R2=0.28, RMSE=0.09) showed strong correlations but had lower correlation with rice canopy LAI. Regression analysis was performed between LiDAR-detected canopy height and manually measured rice canopy LAI. The results indicated that the prediction model based on canopy height (R2=0.77, RMSE=0.03) was more accurate.

The time’s arrow of macroscopic physical phenomenon is reflected by irreversible physical process, which essentially occurs from small probability state to high probability state. In this paper, simplified models are proposed to understand the macroscopic physical process. In order to describe the information of a physical system, we defined the full self-information as "information height" to describe the complexity or difficulty of a macrostate of physical system. In this way, the direction of macroscopic physical process is from high information height to low information height. We can judge the direction of physical process by the information height. If we want the macroscopic physical process to evolve from the low information height state to the high information height state, the system need to add extra information and corresponding energy to increase the information height.

Plants are an important feature of urban ecosystems which provide numerous environmental and ecosystem benefits such as defenses against noise and air pollution and conservation of biodiversity. The aim of this study was to investigate the structure and composition of urban vegetation in different urban habitats like roadsides, parks, gardens and playgrounds in Dhaka South City area. Stratified random sampling method was used in this study. A total of 221 plant species belonging to 63 families were identified and recorded. Among all plant species Swietenia macrophylla, Polyalthia longifolia, Cocos nucifera, Samanea saman, and Artocarpus heterophyllus are recorded as the most dominant. Most of the tree and shrub population were found between 6-9 m and 1-3m height classes whereas most of tree and shrub population were found in between 10-15cm dbh classes. Highest IVI was found for Swietenia macrophylla (193.22%) followed by Polyalthia longifolia (184.59%), Samanea saman (138.37%), Cocos nucifera (79.9%) and Delonix regia (68.27%) respectively. Average frequency, density, dbh and basal area were found 46.82%, 138.28 tree ha^-1, 458.59 cm ha^-1 and 12.33 m² ha^-1 respectively. Findings of this study reveals that structural attributes of plant represent quite young and still developing vegetation. This research will help to plan for future green infrastructure which will maintain ecosystem function, therefore, providing longer term benefits for the city dwellers.

We consider partition functions, in the form of state sums, and associated probabilistic measures for aperiodic substrates described by model sets and their associated tiling spaces. We propose model set tiling spaces as microscopic models for small scales in the context of quantum gravity. Model sets possess special self-similarity properties that allow us to consider implications on large and observable scales from the underlying (non-ergodic) dynamics. In particular we consider the implication of the underlying aperiodic substrate for the well known problem of time in quantum gravity, and propose a correspondence between small and large scales, the so-called ergodic correspondence, that addresses the emergence of matter properties and spacetime structure. In the process we find a possible bound in the mass spectrum of fundamental particles.

Solar flares are characterized by sudden bursts of electromagnetic radiation from the Sun’s surface, and caused by the changes in magnetic field states in solar active regions. Earth and its surrounding space environment can suffer from various negative impacts caused by solar flares ranging from electronic communication disruption to radiation exposure-based health risks to the astronauts. In this paper, we address the solar flare prediction problem from magnetic field parameter-based multivariate time series (MVTS) data using multiple state-of-the-art machine learning classifiers that include MINImally RandOm Convolutional KErnel Transform (MINIROCKET), Support Vector Machine (SVM), Canonical Interval Forest (CIF), Multiple Representations SEQuence Learner (Mr-SEQL), and Long Short-Term Memory (LSTM)-based deep learning model. Our experiment is conducted on the on the Space Weather ANalytics for Solar Flares (SWAN-SF) benchmark data set, which is a partitioned collection of MVTS data of active region magnetic field parameters spanning over 9 years of operation of the Solar Dynamics Observatory (SDO). The MVTS instances of the SWAN-SF dataset are labeled by GOES X-ray flux-based flare class labels, and attributed to extreme class imbalance because of the rarity of the major flaring events (e.g., X and M). As a performance validation metric in this class-imbalanced dataset, we used the true skill statistic (TSS) score. Finally, we demonstrate the advantages of the MVTS learning algorithm MINIROCKET, which outperformed the aforementioned classifiers without the need for essential data preprocessing steps such as normalization, statistical summarization, and class imbalance handling heuristics.

Infant hepatitis B vaccine coverage in China is high, with over 95% of infants immunized; however, high vaccine coverage can often mask low timeliness. The vaccination interval between the second and third dose is not clearly defined by immunization guidelines in China. This retrospective cohort study assessed the time interval distribution of hepatitis B vaccination among a cohort of randomly selected live births from Centers for Disease Control and Prevention across four provinces or municipalities in China between January 2017 and December 2021. Among the infants analyzed, 163,224 received the first dose of hepatitis B vaccine with 146,905 (90.0%) and 135,757 (83.2%) infants receiving the second and third doses, respectively. A total of 132,577 (90.2%) infants received the second dose between 28–61 days after the first dose. Of the 119,437 (88.0%) infants that completed the hepatitis B series between 61–214 days after the second dose, 87,067 (64.1%) infants were vaccinated with the third dose between 151–180 days after the second dose. The time interval distribution for the three doses of hepatitis B vaccine varied across the four provinces or municipalities (P&lt;0.001). Of the 58,077 infants who completed the hepatitis B vaccine series, 36,377 (62.6%) infants used the same type of hepatitis B vaccine for all three doses. Overall, the timeliness of hepatitis B vaccination for infants was lower than expected, with regional disparities observed. This highlights the need for improved timeliness through the introduction of a defined timeframe for the last two doses of vaccine, and training for obstetricians and related personnel.

Long-term continuous time series of SO2 emissions are considered critical elements of both volcano monitoring and basic research into processes within magmatic systems. One highly successful framework for computing these fluxes involves reconstructing a representative time-averaged SO2 plume from which to estimate the SO2 source flux. Previous methods within this framework have used ancillary wind datasets from reanalysis or numerical weather prediction (NWP) to construct the mean plume and then again as a constrained parameter in the fitting. Additionally, traditional SO2 datasets from ultraviolet (UV) sensors lack altitude information which must be assumed to correctly calibrate the SO2 data and to capture the appropriate NWP wind level which can be a significant source of error. We have made novel modifications to this framework which do not rely on prior knowledge of the winds and therefore do not inherit errors associated with NWP winds. To perform the plume rotation, we modify a rudimentary computer vision algorithm designed for object detection in medical imaging to detect plume-like objects in gridded SO2 data. We then fit a solution to the general time-averaged dispersion of SO2 from a point source. We demonstrate these techniques using SO2 data generated by a newly developed probabilistic layer height and column loading algorithm designed for the Cross-track Infrared Sounder (CrIS), a hyperspectral infrared sensor aboard the Joint Polar Satellite System’s Suomi-NPP and NOAA-20 satellites. This SO2 data source is best suited to flux estimates at high-latitude volcanoes and at low-latitude, but high-altitude volcanoes. Of particular importance, IR SO2 data can fill an important data gap in the UV-based record: estimating SO2 emissions from high-latitude volcanoes through the polar winters when there is insufficient solar backscatter for UV sensors to be used.

We reduplicate the Book “Dark Energy” by M. Li, X-D. Li, and Y. Wang, given zero-point energy calculation with an unexpected “length’ added to the ‘width’ of a graviton wave just prior to specifying the creation of ‘gravitons’, using the Rosen and Israelit model of a nonsingular universe. In doing so we are in addition to obtaining a wavelength 10^30 times greater than Planck’s length so we can calculate DE, may be able to with the help of the Rosen and Israelit model have a first approximation as to the arrow of time, and a universe with massive gravity. We have left the particulars of the nonsingular starting point undefined but state that the Rosen and Israelit model postulates initial temperatures of 10^-180 Kelvin and also a value of about Planck temperature, at 10^-3 centimeters radii value which may satisfy initial conditions asked by t’Hooft for describing an arrow of time. A key assumption is that the DE is formed at 10^-3 cm, after an expansion of 10^30 times in radii, from the Planck length radius nonsingular starting point. The given starting point for DE in this set of assumptions is where there is a change in the cosmic acceleration, to a zero value, according to Rosen and Israel, with time t = 1.31 times 10^-42 seconds. Which may be where we may specify a potential magnitude, V, which has ties into inflaton physics. The particulars of the model from Rosen and Israelit allow a solution to be found, without discussion of where that nonsingular starting point came from, a point the author found in need of drastic remedies and fixes.

This paper aims to discuss the relationship between financial development and inflation in Kenya using time series data between 1973 and 2021. The short- and long-run impact of financial development on inflation remains an important issue in the empirical and theoretical literature especially for country specific, but has yet to receive significant research consideration. For this purpose, the paper uses an ARDL analysis method, which is considered an advanced analytical model. Empirical findings confirmed that financial development has a significant long-run impact on inflation in Kenya. On the contrary, results confirmed that there is no significant short-run effect of financial development on inflation. In addition, there is significant long-run and short-run negative relationship between interest rate and inflation. The results indicate significant long-run Granger and ARDL causality from financial development to inflation. The main policy implications of the empirical results of this paper suggest supervision of financial sector must be directed in a way that would stimulate a stable and a moderate inflation rate. In particular, both financial institution and government should enhance the infrastructures of the financial market and promote the utilisation of financial services.

Many systems in nature and laboratories are far from equilibrium and exhibit significant fluc- tuations, invalidating the key assumptions of small fluctuations and short memory time in or near equilibrium. A full knowledge of Probability Distribution Functions (PDFs), especially time- dependent PDFs, becomes essential in understanding far-from-equilibrium processes. We consider a stochastic logistic model with multiplicative noise, which has gamma distributions as stationary PDFs. We numerically solve the transient relaxation problem, and show that as the strength of the stochastic noise increases the time-dependent PDFs increasingly deviate from gamma distributions. For sufficiently strong noise a transition occurs whereby the PDF never reaches a stationary state, but instead forms a peak that becomes ever more narrowly concentrated at the origin. The addition of an arbitrarily small amount of additive noise regularizes these solutions, and re-establishes the existence of stationary solutions. In addition to diagnostic quantities such as mean value, standard deviation, skewness and kurtosis, the transitions between different solutions are analyzed in terms of entropy and information length, the total number of statistically distinguishable states that a system passes through in time.

Copper is a heavy metal used in many industries and known for its negative impacts on the environment and human’s health. A novel structured metal organic framework (MOF) was used for copper adsorption for this work. SEM, EDAX, XRD and FTIR were done to confirm the structure of MOF prepared. MOF of 0.05 gm was used to examine its ability in Cu+ 2 removals with different initial concentrations of Cu+2 and pH values (5, 7 and 9). The prepared MOF was able to achieve Cu removal with 94.6%, 93%, 91.5%, and 92.5 % for the initial concentrations of 5, 10, 15, and 20 ppm respectively. It also performed very well for pH 5 and 7 with average removal ranging from 93.9%-95% for pH 5 and 7 for the initial concentrations of 5, 10, and 15 respectively which indicate that the prepared MOF is of high ability in Cu+ 2 removal.

This study investigates the impact of Foreign Direct Investment (FDI) on economic growth and examines the causality between FDI and economic growth in Bangladesh during 1972-2013. Gross Domestic Product (GDP), export performance (EXP), Foreign Direct Investment (FDI), and Gross Fixed Capital Formation (GFCF) are considered to capture the objective of the study. The study methodology includes some systematic steps. As the data used in the study is time-series in nature, the author employs unit root tests, and in this case, Augmented Dickey-Fuller (ADF) and Phillips-Perron (PP) tests are used. Then Johansen’s cointegration test, Granger causality test, regression with Newey-West Standard Error and Vector Error Correction Model (VECM) are applied. By using the ADF and PP test the study reveals that the variables of four-time series are integrated of I (1) i.e. they are stationary at first difference. Regression analysis result demonstrates that FDI has a positive effect on economic growth. The Granger Causality test discloses that there is a unidirectional relationship between FDI and economic growth. But the VECM estimation finds that in the long run FDI negatively affects economic growth.

Extensive, but remote oil and gas fields of the United States, Canada, and Russia require the construction and operation of extremely long pipelines. Global warming and local heating effects lead to rising soil temperatures and thus a reduction in the sub-grade capacity of the soils; this causes changes in the spatial positions and forms of the pipelines, consequently increasing the number of accidents. Oil operators are compelled to monitor the soil temperature along the routes of the remoted pipelines in order to be able to perform remedial measures in time. They are therefore seeking methods for the analysis of volumetric diagnostic information. To forecast soil temperatures at the different depths we propose compiling a multidimensional dataset, defining descriptive statistics; selecting uncorrelated time series; generating synthetic features; robust scaling temperature series, tuning the additive regression model to forecast soil temperatures.

The search for periodic signals from blazars has become an actively pursued field of research in recent years. This is because periodic signals bring us information about the processes occurring near the innermost regions of blazars, which are mostly inaccessible to our direct view. Such signals provide insights into some of the extreme conditions that take place in the vicinity of supermassive black holes that lead to the launch of the relativistic jets. In addition, studies of characteristic timescales in blazar light curves shed light on some of the challenging issues in blazar physics that includes disk-jet connection, strong gravity near fast rotating supermassive black holes and release of gravitational waves from binary supermassive black hole systems. However, a number of issues associated with the search for quasi-periodic oscillations (QPOs) in blazars e.g., red-noise dominance, modest significance of the detection, periodic modulation lasting for only a couple of cycles and their transient nature, make it difficult to estimate the true significance of the detection. Consequently, it also becomes difficult to make meaningful inferences about the nature of the on-going processes. In this proceedings, results of study focused on searching for QPOs in a number of blazar multi-frequency light curves are summarized. The time series analyses of long term observations of the blazars revealed the presence of year-timescale QPOs in the sources including OJ 287 (optical), Mrk 501 (gamma-ray), J1043+2408 (radio) and PKS 0219 -164 (radio). As likely explanations, we discuss a number of scenarios including binary supermassive black hole systems, Lense–Thirring precession, and jet precession.

The decline in assisted reproductive technology (ART) success among older women, attributed to decreased oocyte quantity and quality, poses a significant challenge. Currently, no consensus ex-ists on the optimal ovarian stimulation protocol for older women undergoing IVF. This retrospec-tive registered cohort study aimed to compare cumulative live birth rates (CLBR), time to live birth (TTLB), and cost-effectiveness in women over 35 years using gonadotropin-releasing hor-mone agonist (GnRHa) or clomiphene-primed ovarian stimulation (CPOS). We performed pro-pensity score matching (PSM) on 2,871 IVF cycles in women over 35 who received either GnRHa or CPOS protocols, resulting in 375 cycles in each group to compare treatment outcomes. Addition-ally, a decision tree model was utilized to assess the cost-effectiveness of the two protocols. Fol-lowing PSM, both groups showed similar baseline characteristics. The CPOS protocol exhibited a higher cycle cancellation rate (13.07% vs 8.00%, p=0.032), yet maintained comparable fertilization and embryo quality. While CLBRs per initial cycle (41.07% vs. 45.33%, p=0.269) and delivery out-comes were similar between the groups after a 24-month follow-up, TTLB was longer in the CPOS group. Notably, the average cost per live birth in the CPOS group was 21.27% less than that in the GnRHa group (￥32,301.42 vs ￥39,174.22). In conclusion, for women over 35 undergoing IVF, the CPOS protocol demonstrated similar CLBR to GnRHa but with lower costs, suggesting its potential as a viable and cost-efficient ovarian stimulation option.

Ultrasonic feedback energy is affected by the variety, planting and growth state of crops, it is difficult to fine application in precision agriculture systems. To this end, an ultrasonic sensor was mounted in a spray boom height detection system. Winter wheat was used as the test object to obtain feedback energy values for the spray boom height from the top of the wheat in the field during six critical growth stages: the standing stage, jointing stage, booting stage, heading stage, filling stage and maturity stage. The relationship between the actual value of the height from the spray boom to the top of wheat (Habw) and the detected value of the height from the spray boom to the top of wheat (Hdbw) was analyzed. A spray boom height detection model based on the ultrasonic sensor during the full growth cycle of wheat was determined. Field validation tests showed that the applicability of the spray boom height detection distance (Dd) of the spray boom height detection model proposed in the present study was 450 mm~950 mm. Within the applicable Dd range, the detection error of the detection model was ≤5 cm during the full growth cycle. This study provides an ultrasonic detection model construction method, which improves the reliability and accuracy of ultrasonic boom height detection for different wheat growth stages.

The total tree height (h) and diameter at breast height (dbh) relationship is an essential tool in forest management and planning. The height—diameter (h-dbh) relationship had been studied with several approaches and for several species worldwide. The nonlinear mixed effect modeling (NLMEM) has been extensively used and lately the resilient backpropagation artificial neural network (RBPANN) approach has been a trend topic for modeling this relationship. The artificial neural network (ANN) is a computing system based in artificial intelligence and inspired in biological neural network for supervised learning. In this study the NLMEN and RBPANN approaches were used for modeling the h—dbh relationship for Durango pine species (Pinus durangensis Martínez) in mixed-species forest from Mexico. The total dataset considered 1,000 (11,472 measured trees) randomly selected from 14,390 temporary forest inventory plots and the dataset was randomly divided into two parts; 50% for training and 50% for testing. An unsupervised clustering analysis was used to grouped the dataset into 10 clusters based on k-means clustering method and plot-variables like density, basal area, mean dbh, mean h, quadratic mean diameter, altitude and aspect. The RBPANN was performed for tangent hyperbolicus (RBPANN-tanh), softplus (RBPANN-softplus), and logistic (RBPANN-logistic) activation functions for functions in cross product of the covariate or neurons and the weights for the ANN analysis. For both training and testing, 10 classical statistics (e.g., RMSE, R2, AIC, BIC, logLik) were computed for the residual values and assess the approaches for h—dbh relationship. For training and testing, the ANNs approach outperformed the NLMEM approach, and the RBPANN-tanh has the best performance in both training and testing phases.

This study employed a deductive research approach and a survey strategy to assess risk perception and its influencing factors among construction workers in Malawi. Three specific construction hazards and their associated risks were selected. The hazards were ‘working at height (WAH) ‘manual handling of loads (MHL)’ and ‘heavy workload or intense pressure to be more productive (HWP)’. The study engaged multistage sampling of 376 subjects. Univariate analysis, factor analysis and multiple linear regressions were performed in order to determine the main influencing factors among the independent variables. The study established that workers were aware of risks posed by their work. They perceived the risk associated with WAH, MHL and HWP as very high (62.7%, = 8.80 ± 1.95); (48.5%, = 8.10 ± 2.38); (57.9%, = 8.49 ± 2.22) respectively. The study identified six factors as variables that showed significant effect on workers’ perception of risk (p < 0.05). These factors were “dreaded factor”, “avoidability and controllability”, “expert knowledge”, “personal knowledge”, education level and age. It is concluded that contractors in the Malawian construction industry should integrate analysis of behaviors and risk perception of the workers and other players to guide the identification of better health and safety interventions at their worksites.

Einstein’s publication of the Special Theory of Relativity in 1905 gave birth to the space-time model as a fundamental arena of the universe. Time has become 4th dimension of space and theoretically one could move backward and forward in time. Hypothetical time travel has been a hot topic of scientific discussion since Kurt Gödel published his article about closed time-like curves (CTC) in 1949. He was aware that his CTC model confirms that there is no physical time. Physicists understood his model as a theoretical frame for time travel. Recent research confirmed that universal space is time-invariant. Motion happens only in space and time is the duration of motion. Nobody can travel in time because time has no physical existence. Time as duration is an emergent physical quantity entering existence in the process of measurement of the duration of material change with clocks. The universal space is utterly timeless. There is no physical time in the universe.

Persons with stroke-induced aphasia (PWAs) are often impaired in tense/time reference (TR) production. It is not clear, however, whether PWAs’ impaired TR production is due to TR-related encoding or retrieval deficits. This study aims at disentangling TR-related encoding deficits from TR-related retrieval deficits in aphasia. Two sentence completion tasks (SCTs) tapping production of past and future reference were administered to eight Greek-speaking PWAs, eight Russian-speaking PWAs, six Italian-speaking PWAs, seven English-speaking PWAs and four groups of language-, age- and education-matched healthy controls. SCT 1 tapped TR-related encoding processes and TR-related retrieval processes to a similar extent. SCT 2 predominantly tapped TR-related retrieval processes. All four control groups performed at ceiling. Three Greek-speaking PWAs, one Russian-speaking PWA, three Italian-speaking PWAs and two English-speaking PWAs showed between-task dissociations. A double dissociation emerged, as some Greek-, Russian- and English-speaking PWAs performed better on SCT 1 than on SCT 2, whereas other Greek- and Italian-speaking PWAs performed worse on SCT 1 than on SCT 2. It will be shown that the experimental design employed here has the potential to disentangle TR-related encoding deficits from TR-related retrieval deficits, as both PWAs with selective TR-related encoding deficits and PWAs with selective TR-related retrieval deficits were identified.

Iris laevigata Fisch. is a perennial aquatic plant with strong cold resistance and showy flowers. However, the flowering period of a single flower is only two days, greatly limiting its potential use in landscaping and the cutting-flower industry. In addition, I. laevigata is often challenged with various abiotic stresses including high salinity and drought in its native habitat. Thus, breeding novel cultivars with prolonged flowering time and higher resistance to abiotic stress is of high importance. In this study, we first performed genome-wide identification of WRKYs, key transcription factors in modulating flowering time and abiotic stress responses. We overexpressed IlWRKY22 in Arabidopsis thaliana and found the flowering time was delayed in the transgenic plants. Molecular characterization further revealed that IlWRKY22 promotes the expression of CO and GA20OX genes in the photoperiod and gibberellin pathways, respectively, and inhibits the expression of SPL3 in the aging pathway. We also created transgenic Nicotiana tabacum overexpressing IlWRKY22, which showed significantly improved resistance to both salt and drought compared to control plants. Specifically, the photosynthetic rate, maximum potential quantum efficiency of Photosystem II (Fv/Fm), and chlorophyll content were higher in the transgenic plants, which was accompanied with higher antioxidant enzyme activity and lower levels of reactive oxygen species. Thus, our study revealed a unique dual function of IlWRKY22, an excellent candidate gene for breeding novel I. laevigata cultivars of desirable traits.

This work describes the preparation of mesoporous silica by the green reaction of rice husk ash (RHA) with glycerol, followed by the modification and the potential use as a drug carrier. The reaction was carried out at 215 °C for 2 h. The solution was further hydrolyzed with deionized water and aged for various times (24, 48, 120, 360, 528 and 672 h) before calcinations at 500 oC for 24 h. Further treatment of prepared mesoporous silica was performed using trimethylmethoxysilane (TMMS) to obtain hydrophobic Mesoporous silica. For all synthesized silica, silica contents were as high as 95%wt, whereas organic residues were less than 3%wt. RHA-glycerol showed the highest specific surface area with smallest pore diameter (205.70 m2/g, 7.46 nm) when aged for 48 h. The optimal hydrolysis-ageing period of 120 h resulted in 500.7 m2/g BET surface area, 0.655 cm3/g pore volume and 5.23 nm pore diameter. The surface modification of RHA-glycerol was succeeded through the reaction with TMMS as confirmed by FTIR. Ibuprofen was selected as a model drug for the adsorption experiments. The adsorption under supercritical CO2 was carried out at isothermal temperature of 40 ˚C and 100 bar, % ibuprofen loading of TMMS modified mesoporous silica (TMMS-g-MS) was 6 times less than mesoporous silica aged for 24 h (MS-24h) due to the hydrophobic nature of modified mesoporous silica, not surface and pore characteristics. The release kinetics of ibuprofen-loaded mesoporous silicas were also investigated in vitro. The release rate of ibuprofen-loaded MS-24h was much faster than that of ibuprofen-loaded TMMS-g-MS, but comparable to the crystalline ibuprofen. The slower release rate was attributed to the diffusion control and the stability of hydrophobic nature of modified silica. This would allow the design for the controlled release drug delivery system.

We propose a Gauss model (GM), a map from time to the bell-shaped Gauss function to model the deaths per day and country, as a quick and simple model to make predictions on the coronavirus epidemic. Justified by the sigmoidal nature of a pandemic, i.e. initial exponential spread to eventual saturation, we apply the GM to existing data, as of April 2, 2020, from 25 countries during first corona pandemic wave and study the model's predictions. We find that logarithmic daily fatalities caused by Covid-19 are well described by a quadratic function in time. By fitting the data to second order polynomials from a statistical chi2-fit with 95\% confidence, we are able to obtain the characteristic parameters of the GM, i.e. a width, peak height and time of peak, for each country separately, with which we extrapolate to future times to make predictions. We provide evidence that this supposedly oversimplifying model might still have predictive power and use it to forecast the further course of the fatalities caused by Covid-19 per country, including peak number of deaths per day, date of peak, and duration within most deaths occur. While our main goal is to present the general idea of the simple modeling process using GMs, we also describe possible estimates for the number of required respiratory machines and the duration left until the number of infected will be significantly reduced.

A novel manufacturing process is presented for producing Nano powders and thin films of CuCoO₂ (CCO) material. This process utilizes three cost-effective synthesis methods: hydrothermal, sol-gel, and solid-state reactions. The resulting delafossite CuCoO₂ samples were deposited onto transparent substrates through spray pyrolysis, forming innovative thin films with a Nano crystal powder structure. Prior to the transformation into thin films, CuCoO₂ powder was first produced using a low-cost approach. The precursors for both powders and thin films were deposited onto glass surfaces using a spray pyrolysis process, and their characteristics were examined through X-ray diffraction, scanning electron microscopy, HR-TEM, UV-visible, and Electrochemical impedance spectroscopy (EIS) analyses was conducted to determine the conductivity in transversal direction of this groundbreaking material for solar cell applications. On the other hand, the sheet resistance of the samples was investigated using the four probe-method to obtain the sheet resistivity and them calculate the in plane conductivity of the samples. We also investigated the aging characteristics of different precursors with varying durations. The functional properties of CuCoO2 samples were explored by studying chelating agent and precursor solution aging periods. Resuming, this study thoroughly discusses the synthesis of delafossite powders and their conversion into thin films, which hold potential as hole transport layers in transparent optoelectronic devices.

The retrieval of tree height percentiles with satellite lidar waveforms over the mountainous ar-eas is greatly challenged due to slanted and rugged topographic relief of underlying ground. A novel algorithm is proposed to extract the height percentiles based on the target response waveform (TRW) that is resolved by using a Richardson–Lucy deconvolution algorithm with an adaptive iterative time. The height metrics of the energy percentiles of 25%, 50%, 75% and 95% for the cumulative TRW distribution are determined by their vertical distances relative to the ground elevation in this study. To validate the proposed algorithm, we select the received waveforms of the Global Ecosystem Dynamics Investigation (GEDI) lidar over the Pahvant Mountains of central Utah, USA. The results reveal that the resolved TRWs resemble closely to the actual target response waveforms from the coincident airborne lidar data, with the mean values of the coefficient of correlation, total bias and root mean square error (RMSE) taking val-ue of 0.92, 0.0813 and 0.0016. In addition, the accuracies of the derived height percentiles from the proposed algorithm have been greatly improved compared with the conventional Gaussian de-composition method and the slope-adaptive waveform metrics method. The RMSE values de-crease by the mean values of 1.96 m and 2.72 m, respectively. It demonstrates that the proposed algorithm has good potential in the extraction of forest structure parameter over rugged moun-tainous areas.

Oscillations in global modes of variability (MoV) form global teleconnections that affect regional climate variability and modify the potential for severe and damaging weather conditions. Understanding the link between certain MoVs and regional climate can improve the ability to more accurately predict environmental conditions that impact human life and health. In this study, we explore the connection between different MoVs, including the Arctic Oscillation (AO), Eurasian teleconnection, Indian Ocean Dipole (IOD), North Atlantic Oscillation (NAO), and El Niño Southern Oscillation (Nino34), with winter and summer climate in the High Mountain Asia (HMA) region, including geopotential height at 250 hPa (z250), 2-m air temperature (T2M), total precipitation (PRECTOT), and fractional snow cover area (fSCA). Relationships are explored for the same monthly period between the MoVs and the climate variables, but also using a lagged correlation analysis to investigate whether any relationship exists at different time lags. We find that T2M has a negative correlation with the Eurasian teleconnection in the Inner Tibetan Plateau and Central China in both winter and summer and a positive correlation in Western China in summer. PRECTOT has a positive correlation with all MoV in most regions in winter, especially with the IOD, and a negative correlation in summer, especially with the Eurasian teleconnection. Snow cover in winter is positively correlated with most indices throughout many regions in HMA, likely due to wintertime precipitation also being positively correlated with most indices. Generally, the AO and NAO show similar correlation patterns with all climate variables, especially in the winter, possibly due to their oscillations being so similar. Furthermore, the AO and NAO are shown to be less significant in explaining the variation in HMA climate compared to other MoVs such as the Eurasian teleconnection. Overall, our results pinpoint different time-windows and specific regions within HMA that exhibit high correlation between climate and MoVs, which might offer additional predictability of the MoVs as well as of climate and weather patterns in HMA and throughout the globe.

Spaceborne altimeters are an important data source for obtaining global sea surface wind speeds (U10). Although many altimeter U10 algorithms have been proposed and they perform well, there is still room for improvement. In this study, the data from ten altimeters were collocated with buoys to investigate the error of the altimeter U10 retrievals. The U10 residuals were found to be significantly dependent on many oceanic and atmospheric parameters. Because these oceanic and atmospheric parameters are inter-correlated, an asymptotic strategy was used to isolate the impact of different parameters and establish a neural-network-based correction model of altimeter U10. The results indicated that significant wave heights and mean wave periods are effective in correcting U10 retrievals, probably due to the tilting modulation of long-waves on the sea surface. After the wave correction, the root-mean-square error of the retrieved U10 was reduced from 1.42 m/s to 1.24 m/s and the impacts of thermodynamic parameters, such as sea surface (air) temperate, became negligible. The U10 residuals after correction showed that the atmospheric instability can lead to errors on extrapolated buoy U10. The buoy measurements with large air-sea temperature differences need to be excluded in the Cal/Val of remotely sensed U10.

Natural circulation loop (NCL) systems are buoyancy-driven heat exchangers that are used in various industrial applications. The concept of passive heat exchange in NCL systems is attractive, because there is no need for an externally driven equipment (e.g., a pump) to maintain the fluid circulation. However, relying on buoyancy as the sole driving force may lead to several potential difficulties, one of which is generation of (possibly) time-varying nonlinearities in the dynamical system, where a difference in the time scales of heat transfer and fluid flow causes the flow to change from a steady-state regime to either an oscillatory regime or a flow-reversal regime, both of which are undesirable. In this paper, tools of symbolic time series analysis (e.g., probabilistic finite state automata (PFSA)) are proposed to identify selected regimes of operation in NCL systems, where the underlying principle is built upon the concept of pattern classification from measurements of fluid-flow dynamics. The proposed method is shown to be capable of identifying the current regime of operation from the initial time response under a given set of operational parameters. The efficacy of regime classification is demonstrated by testing on two data sets, generated from numerical simulation of a MATLAB SimuLink model that has previously been validated with experimental data. The results of the proposed PFSA-based classification are compared with those of a hidden Markov model (HMM) that serves as the baseline.

Research has shown that emotional states may influence the subjective experience of time. The present study involved 111 healthy adult participants and examined the impact of emotional stimuli on time perception, using a time estimation task with four conditions: in one of the conditions, participants estimated the exposure time of a black screen, wherein the duration could vary be-tween 2 to 7 s (condition without emotional interference); in the other conditions, participants es-timated the exposure time (also ranging from 2 to 7 s) of images that would induce pleasant, un-pleasant, or neutral emotions, to which participants were instructed to focus their attention (pleasant, unpleasant, or neutral emotions). The results showed that participants estimated “shorter” time intervals (underestimation) for pleasant and unpleasant images compared to the condition without interference, but no significant differences were found between the neutral condition and the condition without interference. It is suggested that increased attention to an ex-ternal stimuli, regardless of its emotional valence, produces an underestimated perception of time.

We consider the problem of scheduling $n$ jobs with identical processing times and given release as well as delivery times on $m$ uniform machines. The goal is to minimize the makespan, i.e., the maximum full completion time of any job. This problem is well-known to have an open complexity status even if the number of jobs is fixed. We present a polynomial-time algorithm for the problem which is based on the earlier introduced algorithmic framework blesscmore (``branch less and cut more''). We extend the analysis of the so-called behavior alternatives developed earlier for the version of the problem with identical parallel machines and show how the earlier used technique for identical machines can be extended to the uniform machine environment if a special condition on the job parameters is imposed. The time complexity of the proposed algorithm is $O(\gamma m^2 n\log n)$, where $\gamma$ can be either $n$ or the maximum job delivery time $q_{\max}$. This complexity can even be reduced further by using a smaller number $\kappa<n$ in the estimation describing the number of jobs of particular types. However, this number $\kappa$ becomes only known when the algorithm has terminated.

The hyper-arid environment is characterized by high inter-annual climatic fluctuations. The yearly average rainfall can change substantially for several years, forming wet or dry sub-periods. Observing rainfall trends over a sub-period can lead to a false perception of a change in the trend but may in fact represent a periodic cycle when examined on a larger time scale. We aimed to better characterize the rainfall regime prevailing in the hyper-arid Arava Valley (Israel/Jordan), and to examine the response of vegetation to annual rainfall. We hypothesized that annual and perennial vegetation would respond differently to wet and dry sub-periods, and that grazing activities will impact vegetation growth. We used a time series of monthly rainfall, from which we calculated Standard Precipitation Index (SPI), and calculated proxies of perennial and annual vegetation over the last four decades using Landsat-derived Normalized Difference Vegetation Index (NDVI). We found no clear trend in rainfall amounts during this period, however we did identify wet and dry sub-periods which were statistically distinct in rain and in vegetation patterns from each other. The highest levels of correlation between rainfall and the NDVI derived proxies were found when examining average rainfall over a period of two- three years for the annual vegetation and over four years for perennial vegetation. Using the Mann-Kendall test, we identified a time lag of two to four years, with the proxies of annual vegetation responding faster than the proxies of perennial vegetation, to shifts between wet and dry sub-period. In addition, we found a consistent difference between natural vegetation cover in Jordan (grazed) and Israel (non-grazed), favoring the development of natural vegetation on the Israeli side. We conclude that integrating between long-term remote sensing satellite imagery and climatic records revealed the greater resilience of perennial vegetation in the hyper-arid region to climatic fluctuation, and enabled us to identify the vegetation’s sensitivity to anthropogenic impact.

For more than ten years, Central Chile faces drought conditions, which impact crop production and quality, increasing food security risk. Under this scenario, implementing management practices that allow increasing water use efficiency is urgent. The study was carried out in kiwifruit trees, located in the O’Higgins region, Chile; for season 2018-2019 and 2019-2020. We evaluate nine vegetation indices in the VNIR and SWIR regions derived from Sentinel-2 (A/B) satellites to know how much variability in the canopy water status could explain. Over the study's site were installed sensors that continuously measure the leaf's turgor pressure (Yara Water-Sensor). A strong correlation between turgor pressure and vegetation indices was obtained with the Spearman's rho coefficient ($\rho$). However, the NIR range's indices were influenced by the vegetative development of the crop rather than its water status. Red-edge showed better performance as the vegetative growth did not affect it. It is necessary to expand the study to consider higher variability in kiwifruit's water conditions and incorporate the sensitivity of different wavelengths.

In this study, we aimed to identify the factors affecting the night-time economy in Hanoi to achieve the sustainable development of this economy. We surveyed four selected groups of subjects: people, tourists, business establishments, and managers in Hanoi City, in which tourists were nationwide but have been on a night tour in Hanoi. We chose a nonrandom convenience sample. With the above sample size, the number of respondents was insufficient, so we selected districts with potential for night economic development including Hoan Kiem, Tay Ho, Dong Da, Nam Tu Liem, Ha Dong, and Gia Lam. We obtained 463 usable surveys. We processed and analyzed the data using SPSS Statistics 26.0 software. Our quantitative study included: (1) testing the suitability of the scale for the variables using Cronbach’s alpha, (2) analyzing the EFA factors to check the convergence of the observed variables and the separation between the independent variables, (3) checking the correlation to evaluate the problem of multicollinearity of the model; , and (4) performing regression analysis to evaluate the impact of the factors on night-time economic development in Hanoi City. The results showed that the variables positively impacted night-time economic development in Hanoi, but we found differences in the levels of their impact. Among the four factors, factor 3 (promotion and sharing) had the strongest impact on night-time economic development, followed by factor 2 (infrastructure and safety), factor 1 (institutions and environment), and factor 4 (nature and resources.)

Leisure-time physical activity (LTPA) is associated with access and use of public open spaces. The “President João Goulart Elevated Avenue” and current denominated “Minhocão” is a facility for leisure activities that are open for people during the night/weekends. The aim of this study was to examine if the prevalence of LTPA among individuals living in the surroundings of Minhocão is different according to proximity to, and use of, the facility. We conducted a cross-sectional study with cluster sampling with people aged ≥18 years who lived in households until 500m and between 501m to 1500m of Minhocão. The survey was conducted between December/2017 until March/2019 with an electronic questionnaire self-responded. We conducted bivariate analysis and Poisson regression to examine possible differences in LTPA according to the proximity of residences and use of Minhocão. The analysis used post-stratification weights. A total of 12,030 telephone numbers of people were drawn (≤500m = 6,942; and &gt;500m to ≤1500m = 5,088). The final sample analyzed were of 235 residents who returned the questionnaires. There was a higher prevalence of individuals engaging in at least 150 minutes per week of LTPA among users than non-users (Prevalence Ratio=2.23, IC95%1.72-2.90). People who used the park had higher prevalence of all types of LTPA than non-users. The results can serve to inform government decision-making on the future of Minhocão.

Fractional-time Schrödinger equation (FTSE) describes the evolution of quantum processes endowed with memory effects. FTSE manifestly breaks all consistency requirements of quantum field theory (unitarity, locality and compliance with the clustering theorem), unless the order of fractional differentiation and integration ( ) falls close to the standard index . Working in the context of the minimal fractal manifold (where , ), we confirm here that FTSE approximates the attributes of gravitational metric and provides an unforeseen generation mechanism for massive fields.

This paper examines interlinkages and hedging opportunities between nine major cryptocurrencies for the period between 30 September 2015 and 4 June 2020, which notably includes the coronavirus disease 2019 (COVID-19) outbreak lasting from early 2020 through the end of the sample period. The results of dynamic conditional correlation (DCC) analysis using a minimum connectedness approach show a high degree of correlation between cryptocurrencies throughout the sample period. However, the correlations reach their minimum values during the COVID-19 pandemic, which indicates that cryptocurrencies acted as a hedge or safe haven during the stressful period of the COVID-19 pandemic. The weight of cryptocurrencies was significantly reduced and their hedging effectiveness varied greatly during the pandemic, which indicates that investors’ preferences changed during the COVID-19 period.