The natural frequency of buildings decreases during a strong-motion earthquake, and the structure loses its stiffness. As a result, understanding the damaging process in the structure owing to changes in structural properties is critical during a seismic excitation. The time-frequency technique can detect the damaged building’s time-varying frequency contents. Wigner distributions (WD), Wigner-Ville distributions (WVD), pseudo-Wigner-Ville distributions (PWVD), smoothed pseudo-Wigner-Ville distributions (SPWVD), and synchrosqueezing transforms (SST) have all become popular in recent years for a variety of earthquake engineering applications, including building damage detection. This study proposes the local maximum synchrosqueezing transform (LMSST) for detecting frequency shifts in buildings during strong earthquakes. The data presented in the research show that the suggested method outperforms as compared to the conventional time-frequency methods for detecting frequency shifting in earthquake-damaged structures.

The open communication is an exigent need for future power system where the time delay is unavoidable. In order to secure the stability of the grid, the frequency must remain within its limited range which is achieved through the load frequency control. The load frequency control signals are transmitted through communication networks which induces time delay that could destabilize the power systems. So, in order to guarantee the stability the delay margin should be computed. In this paper, we present a new method for calculating the delay margin in load frequency control systems. The transcendental time delay characteristics equation is transformed to frequency dependant equation. The spectral radius is used to find the frequencies at which the roots crosses the imaginary axis. The crossing frequencies are determined through the sweeping test and the binary iteration algorithm. A one-area load frequency control system is chosen as case study. The effectiveness of the proposed method has been proved through comparing with the most recent published methods. The method shows its merit with less conservativeness and less computations. The PI controller gains are preferable to be chosen large to reduce the damping, however, the delay margin decreases with increasing the PI controller gains.

In this paper, four types of open service signals of BDS-3 satellite (B1I, B1C, B2a, and B3I) and B2I signals broadcasted by BDS-2 satellites were used in the time frequency transfer and positioning experiments with signal coexisting in BDS system, and the single frequency PPP (precise point positioning) method was used. Modified GRoup And PHase Ionospheric Correction (GRAPHIC) method was proposed and verified by the experiment. The results show that 18 selected stations can achieve decimeter-level positioning results with single frequency. Compared with the general observation method, the proposed modified GRAPHIC method improves the stability and precision of positioning and timing significantly, and the positioning accuracy of 5 frequency signals is increased 40.4%, 32.2%, 80.3%, 12.4%, and 10.3%, respectively. The frequency stability can reach the same accuracy as that of dual-frequency with BDS in the current state.

Modern electrical power systems integrate ancillary services to provide security and quality of service in real-time operation because of the intense variations in frequency caused by the massive development and uncertainty of solar-wind generation. Therefore, this ancillary services market focuses on power reserves for secondary and tertiary frequency control. Adjusting reserves and dispatching plants is a manual instruction executed by the system operator to maintain the frequency in the normal operating state (49.80≤f≤50.20 Hz). However, in the absence of an economic model for real-time power reserve reallocation in the ancillary services market, the reserve adjustments made by the system operator are not always optimal since they generate a displacement between the scheduled and actual marginal costs. Then, this work proposes a methodology for operating the ancillary services market in real-time through a dynamic and hourly mathematical model that integrates the variability of solar-wind generation, the demand monitoring curve, and the trajectory of the marginal cost. This model minimizes power reserve costs, which are governed by hourly price auctions, for candidate plants classified as supra/infra-marginal and can optimally reallocate power reserves for secondary and tertiary frequency control.

The development of mineral resources in China has gradually entered the stage of deep mining. Rock burst, collapse and other ground pressure disasters caused by deep high stress have become major hidden dangers restricting mine safety production. Microseismic monitoring technology is an important means of ground pressure risk prediction. In this paper, the wavelet coefficient threshold denoising method in time-frequency domain, STA/LTA method, AIC method, Skew and Kurtosis method are studied, and the automatic P-phase onset time picking model based on noise reduction and multiple detection indexes is established. Through the effect analysis of microseismic signals collected by microseismic monitoring system of coral Tungsten Mine in Guangxi, automatic P-phase onset time picking is realized. the reliability of the P-phase onset time picking method proposed in this paper based on noise reduction and multiple detection indexes is verified. The picking accuracy can still be guaranteed under the severe signal interference of background noise, power frequency interference and manual activity underground mine, Which is of great significance to the data processing and analysis of microseismic monitoring.

In this paper, the concept of absolute airspace is further elaborated, and the time transform effect, the frequency transform relation of clock timing, and the principle of Doppler effect of special relativistic light are analyzed and demonstrated. Based on the concept of absolute airspace, a new and accurate Doppler effect relation of light (electromagnetic wave) is proposed. It is proved that there is a synchronous relationship between the time shift effect and the frequency change of the timing inside the clock. When the light (electromagnetic wave) source is in motion, the Doppler effect includes two physical mechanisms: the frequency change caused by time transformation effect and the frequency change caused by relative motion. When the light source is in motion, the Doppler effect of the light there are some differences in different directions due to the rotation of the earth. The relation of Doppler effect of special relativistic light is only a highly approximate relation, and its theoretical basis, special relativity, is flawed in principle.

Qualitative and quantitative values estimation is a crucial aspect of social data science and plays a vital role in social and psychological research. Numerous methods of personal values measurement such as Schwartz Value Survey (SVS) and its re-modified versions have been proposed and invented, but many are challenged with one or more limitations. In this article, an alternative approach in a new paradigm of values measurement called Kabiru’s Value Survey (KVS) was proposed to measure the relative degree of importance or significance attached to particular value-actions of an individual(s) in a given population over a period. The methodological innovations in KVS unlike other existing methods of human value measurement include the use of habitually reported practices associated with a particular value-action in place of judging the series of Schwartz hypothetical statements, the use of multiple dependent variables rather than a single coded hypothetical statement. In terms of data analysis, a new approach of multivariate compression is introduced which merges the chain of multiple dependent variables into one coded scale. Psychometric result interpretation is also another innovative aspect of KVS methodology. Finally, the proposed methodology however solved some of the criticized limitations of the other methods of human value measurement.

Classical numerical methods for solving ordinary differential equations often produce less accurate results when applied to problems with oscillatory or periodic behaviour. To adapt them for such problems, they are usually modified using the exponential fitting technique. This adaptation allows for the construction of new methods from their classical counterparts. The new methods are usually more accurate, efficient and suitable for handling the oscillatory or periodic behaviour of the problem. In this work, we construct a two-parameter exponentially-fitted Taylor method suitable for solving oscillatory or periodic problems that possess two frequencies. The construction algorithm is based on a proposed six-step flowchart discussed by authors in related literature. Two standard test problems were used to illustrate the accuracy and performance of the proposed method.

The signal processing technique is one of the principal tools for diagnosing power quality (PQ) issues in electrical power systems. The Discrete Fourier Transform (DFT) is a frequency analysis technique used to process power system signals and identify PQ problems. However, the DFT algorithm may lead to spectral leakage and picket-fence effect problems for asynchronously sampled signals that contain harmonic, inter-harmonic, and flicker components. To resolve this shortcoming, a hybrid method for frequency estimation based on a second-level DFT approach and a frequency-domain interpolation algorithm to obtain the accurate fundamental frequency of a power system is proposed in this paper. This method uses a second-level DFT to compute the cosine and sine parts for the fundamental frequency components of the acquired signals. Then, a frequency-domain interpolation approach is adopted to determine the amplitude ratio for the cosine and sine parts of the system's fundamental frequency. To demonstrate the performance of the proposed frequency estimation method, the observation window used by this paper to evaluate different estimation algorithms is 200 ms. According to the IEC standards, a 200 ms acquisition window is recommended for power system quality assessment. A set of mixed signals with harmonic, inter-harmonic, and flicker components with the fundamental frequency deviation is used. The evaluation results demonstrate the superiority of the new method over other approaches for assessing asynchronously sampled signals contaminated with noise, harmonic, inter-harmonic, and flicker components.

A new method for short circuit fault location is proposed based on instantaneous signal measurement and its derivatives, and is based on the retardation phenomena. The difference between the times in which a signal is registered in two detectors is used to locate the fault. Although a description of faults in terms of a lumped circuit is useful for elucidating the methods for detecting the fault. This description will not suffice to describe the fault signal propagation hence a distributed models is needed which is given in terms of the telegraph equations. Those equations are used to derive a transmission line transfer function, and an exact analytical description of the short circuit signal propagating in the transmission line is obtained. The analytical solution was verified both by numerical simulations and experimentally.

The earthquake alert of the early warning systems is based on the delay that the S waves have in reference to the P waves and on the interpretation of the P waves’ specific parameters. One of the most used parameters for estimating the moment magnitude of an earthquake is the characteristic period measured in the first 3 seconds of the appearance of the P wave. The typical method determines the characteristic period in the time domain, based on the velocity wave and the displacement wave. In the present work, we present a method for estimating the frequency of the characteristic period. This method includes zero padding of the P wave sequence, conversion of the extended sequence from the time domain to the frequency domain, the identification of local frequency maxima and the calculation of the weighted average of the frequency based on the identified maxima. Tests conducted on synthetic signals, as well as standard deviation evaluation tests for simultaneous recordings on several stations, reveal better performance to the usual method.

So far, scientific studies on high frequency welding (HF) have observed the three main parameters: anode current, welding time and pressure of upper electrode. Some authors have also observed and studied the welding frequency, the power, and the values of the dielectric constants of the materials or the angle of dielectric losses. Due to the complex effects that the parameters have on the quality of the welded joint, it is necessary to extend the research and study the mutual relationships between a large numbers of process parameters on the welded joint in order to achieve satisfactory strength of the welded joint. In this research, the number of considered parameters is increased to 17, each of which is relevant to the processes of HF welding, and their mathematical equations are presented. The research is carried out on a HF welding machine improved with a linear pneumatic actuator for lowering the upper electrode and regulating the compressive force, and a measuring machine with the appropriate measuring method for determining the breaking forces with a tension gage and performing the „T“ test is made. Numerous researches were carried out on the functional changes of the process parameters of the percentage share of the values of the coupling capacitor, the anode current and the welding time on the values of the breaking forces of the welded joints. Based on the conducted research, it was concluded that the optimization of the process parameters of HF machine must be performed before the welding process, which is determined by a certain amount of energy that must be introduced into the material. These parameters are the capacity of the output capacitor, i.e., the value of the electric current flowing through the material and the time for the development of the operating power to produce welded joints with a certain strength and quality of welded joints for a specific material used in the process.

The principal aim of a spectral observer is twofold: the reconstruction of a signal of time via state estimation and the decomposition of such a signal into the frequencies that make it up. A spectral observer can be catalogued as an online algorithm for time-frequency analysis because is a method that can compute on the fly the Fourier transform (FT) of a signal, without having the entire signal available from the start. In this regard, this paper presents a novel spectral observer with an adjustable constant gain for reconstructing a given signal by means of the recursive identification of the coefficients of a Fourier series. The reconstruction or estimation of a signal in the context of this work means to find the coefficients of a linear combination of sines a cosines that fits a signal such that it can be reproduced. The design procedure of the spectral observer is presented along with the following applications: (1) the reconstruction of a simple periodical signal, (2) the approximation of both a square and a triangular signal, (3) the edge detection in signals by using the Fourier coefficients, (4) the fitting of the historical Bitcoin market data from 2014-12-01 to 2018-01-08 and (5) the estimation of a input force acting upon a Duffing oscillator. To round out this paper, we present a detailed discussion about the results of the applications as well as a comparative analysis of the proposed spectral observer vis-à-vis the Short Time Fourier Transform (STFT), which is a well-known method for time-frequency analysis.

Crowd counting is of significant importance for numerous applications, e.g., urban security, intelligent surveillance and crowd management. Existing crowd counting methods typically require specialized hardware deployment and strict operating conditions, thereby hindering their widespread deployment. To acquire a more effective crowd counting approach, a device-free counting method based on Channel Status Information (CSI) is proposed, which could mitigate environment noise through wavelet transform and extract the amplitude or phase covariance matrix as the feature vector. Moreover, both the spatial diversity and frequency diversity are leveraged to improve detection robustness. The accuracy of the proposed CSI-based method is compared with a renowned crowd counting one, i.e., Electronic Frog Eye: Counting Crowd Using WiFi (FCC). The experimental results reveal an accuracy improvement of 30% over FCC.

This study compared cortical responses to speech in preschoolers with typical language development (TLD) and Developmental Language Disorder (DLD), and in adults. We investigated whether top-down language effects modulate speech perception in an adult-like manner. We compared cortical mismatch responses (MMR) during passive perception of speech differing in linguistic complexity in three groups of participants: preschoolers with TLD (n=11), preschoolers with DLD (n=16) and adults (n=20). We also measured children’s phonological skills and investigated if they are associated with the cortical responses. MMR results indicated top-down language effects in adults, with enhanced cortical discrimination of lexical stimuli but not of non-words. In preschoolers, the TLD and DLD groups did not differ on the MMR measures and no top-down effects were detected. Moreover, we found no association between MMRs and phonological awareness skills, even though the DLD group’s phonological skills were significantly lower. Our findings suggest that top-down language modulations on speech discrimination may not be present during early childhood, and that children with DLD may not exhibit cortical speech perception deficits. The lack of association between phonological and MMR measures indicates that further research is needed to understand the link between language skills and cortical activity in preschoolers.

The frequency synthesizer is a critical component in Cs beam clock technology. In this paper, we present a demonstration of a direct microwave frequency-synthesis chain for a cesium-beam atomic clock, which utilizes frequency multiplication and a dual-phase-locked loop mode. A detailed analysis of the frequency-synthesis chain is conducted, and a mathematical model is established. The phase settling time and system stability are simulated, measured, and verified. The experimental results for the phase settling time align with the simulation outcomes. The phase settling time can be adjusted within the range of 644.5 µs to 1.5 ms, and the absolute phase noise values are -63.7 dBc/Hz, -75.7 dBc/Hz, -107.1 dBc/Hz, and -122.5 dBc/Hz at 1 Hz, 10 Hz, 1 kHz, and 10 kHz offset frequencies, respectively. Additionally, the Ramsey fringes are detected, and the Allan deviations of the 10 MHz output from the cesium-beam atomic clock are measured to be 2.99×10−12 at 1s and 8.02×10−14 at 10,000 s.

The vibration response of soil is a key property in the field of agricultural soil tillage. Vibration components of tillage machinery are generally used to reduce tillage resistance and improve work efficiency, the pressure variation under low-frequency vibration will affect the fragmentation and dispersion of farmland soil. However, the gradient of pressure variation, frequency domain response, and effective transmission range are unclear. A new method based on DEM (Discrete Element Method) is presented to study the vibration response and pressure transmission under low-frequency vibration. Bench test results showed that peak pressure positively correlates with the vibration frequency and attenuates rapidly at the vibration distance of 100 to 250 mm. The results data were also selected to determine the simulation model parameters. Amplitude, vibration frequency, and soil depth were used as test factors in single-factor simulation tests, and their effects on the peak pressure, frequency domain response, and effective transmission distance were analyzed. The results showed a positive relationship between the peak pressure and the test factors. The peak pressure increases with a maximum gradient of 19.02 kPa/mm at a vibration distance of 50 mm. The amplitude, vibration frequency, and soil depth positively correlate with the dominant frequency amplitude. The main frequency is independent of amplitude and soil depth. At the vibration distance of 250 mm, the dominant frequency is approximately twice the vibration frequency at 7–11 Hz and approximately equal to the vibration frequency at 13–15 Hz. Multiple exponential functions were used to fit the peak pressure attenuation function, obtaining an effective transmission distance range of 347.15 to 550.37 mm for the 5kPa cut-off pressure. For a soil depth of 300 mm, the vertical shear wave diffusion angle is greater than the horizontal shear wave diffusion angle. The study clarifies the vibration response of soil under low-frequency vibration, which helps to design vibration type soil-engaging components of tillage machinery and match vibration parameters for energy saving and resistance reduction in soil tillage.

Self-healing ceramic composites are promising smart materials for high-temperature applications. To better understand their behaviors under service conditions, numerous studies have been performed both experimentally and numerically, and kinetics parameters such as activation energy and frequency factor are reported to be indispensable for investigating healing phenomena. Here, we propose a method for determining the kinetic parameters of self-healing ceramic composites based on the oxidation kinetics model of strength recovery. These parameters are determined by an optimization method using experimental strength recovery data under various healing temperatures and times and microstructural features on the fractured surfaces. Alumina and mullite matrix-based self-healing ceramic composites, such as Al2O3/SiC, Al2O3/TiC, Al2O3/Ti2AlC (MAX phase), and mullite/SiC, were selected as target materials. The theoretical strength recovery behaviors of the cracked specimens obtained from the determined kinetic parameters were compared with the experimental results. The determined parameters are within the previously reported range, and the predicted strength recovery behaviors are reasonably agreed with the experimental values. The proposed method can also be applied to other self-healing ceramics with matrices reinforced with different healing agents to evaluate oxidation rate, crack healing rate, and theoretical strength recovery behaviors for designing self-healing materials used in high temperature applications. Furthermore, the healing ability of composites can be fairly discussed regardless of the type of strength recovery test.

Soil nitrite (NO2‒) is an important reactive intermediate in many nitrogen transformation processes, but it is unstable under acidic conditions. Canonical extraction method of soil NO2‒ with potassium chloride (KCl) solution greatly underestimates its concentration. In order to reflect the concentration more accurately, we optimized the extraction method of soil NO2‒ in this study. Moreover, soil ammonium (NH4+) and nitrate (NO3‒) were also systematically investigated to achieve efficient extraction of soil inorganic nitrogen. The results showed that un-buffered KCl significantly underestimated soil NO2‒ concentration compared to DIW. The highest recovery of NO2‒ was obtained by extracting with DIW at 10 min of oscillation for three soils. Compared with DIW, the concentration of NH4+ and NO3‒ in soil extracted from KCl solution increased significantly. Furthermore, the soil inorganic nitrogen content of extracts stored at 4°C for one day were closer to directly measurements of fresh samples than the other storage methods. Overall, the recommend analysis method for soil NO2‒ was extracted by DIW, oscillated for 10 min, and filtered by a 0.45 µm filter, and soil NH4+ and NO3‒ were extracted with KCl solution and oscillated for 30 min. The extract should be stored at 4°C and analyzed within 24 hours.

An approximate calculation of the spatial characteristics on finite range is required, so one quantitative continuum represents the accumulation of infinite great quantities is artificially divided it into smaller and camparable parts in which calculus operation can be applied .This operation is defined as Theorem 1 in which infinity is not involved, there is a camparable finity is constantly (forever) approaching and not reaching infinity, and only staying within a finite range. Theorem 1 can exist in this paper as a new mathematical basis for physics. Because the essence of all physical quantities is size comparison, and the size comparison relation of matter can only be space/time, so relation formula space/time is the only expression of the concept of matter, all physical quantities are applicable to this expression, each different physical quantity is a multi-dimensional representation of this expression. A new mass energy formula is aslo derived from this paper.

This paper introduces the exponential time differencing (ETD) technique as a numerical method to solve efficiently American vulnerable options pricing. We address several challenges, including removing cross-derivative terms through appropriate transformations, treating early-exercise opportunities using the penalty method, and substituting fixed boundary conditions with corresponding one-sided finite differences. The proposed method is shown to be both accurate and efficient through numerical experiments, which also compare the results with existing methods and analyse the numerical stability and convergence rate.

Estimating peak flow for a catchment is commonly undertaken using the design event method, however this method does not allow for the understanding of uncertainty in the result. This research first presents a simplified method of fragments approach to rainfall disaggregation that ignores the need to consider seasonality, offering a greater diversity in storm patterns within the resulting sub-daily rainfall. By simulating 20 iterations of the disaggregated sub-daily rainfall within a calibrated continuous simulation hydrologic model, we were able to produce multiple long series of stream flow at the outlet of the catchment. With this data, we investigated the use of both the annual maximum and peaks over threshold approaches to flood frequency analysis and found that for a one in 100 year annual exceedance probability peak flow, the peaks over threshold method (333m3/s ±50m3/s) was significantly less uncertain than the annual maximum method (427m3/s ±100m3/s). For the one in 100 year annual exceedance probability, the median peak flow from the peaks over threshold method (333m3/s) produced an outcome comparable to the design event method peak flow (328m3/s), indicating that this research offers an alternative approach to estimating peak flow, with the additional benefit of understanding the uncertainty in the estimation. Finally, the paper highlighted the impact that length and period of streamflow has on peak flow estimation and noted that previous assumptions around the minimum length of gauged streamflow required for flood frequency analysis may not be appropriate in particular catchments.

Clinical work conducted over the last seventeen years at the EEG Institute in Los Angeles and by other neurofeedback providers around the world has demonstrated the utility of extending frequency-based neurofeedback deep into the infra-low frequency (ILF) region, using the method of endogenous neuromodulation described herein. The method is characterized by the absence of any overt reinforcements, which makes it possible to extend the clinical reach to extremely low frequencies. As the training frequency is lowered, the signal becomes more difficult to discriminate, and ultimately it can only be discerned by the brain itself, in the process of endogenous neuromodulation. The method emulates how the brain does skill learning in general: It must observe itself performing the skill, with feedback on its performance. While the immediate target of ILF neurofeedback is enhanced self-regulatory competence--with symptomatic relief and functional recovery the secondary consequences, progressive lowering of the target frequencies has led to improved outcomes in application to challenging dysfunctions such as episodic suicidality, migraine, seizures, and bipolar mood swings. The work has also yielded insights into how the frequency domain is organized. The training proceeds best at frequencies that are specific to each individual, and these are referred to as optimal response frequencies (ORFs). These frequencies differ for various placements but stand in two fixed relationships to one another, one that holds over the EEG spectral range, and another that holds over the entire ILF range. Training in the ILF region engages the dynamics of the glial-neuronal networks, which govern tonic, resting state regulation. The collective clinical experience with ILF neuromodulation within a large practitioner network supports the case for making protocol-based, individualized ‘homeodynamic’ regulation a therapeutic priority, particularly for our most impacted clinical populations: addiction, trauma formations, traumatic brain injury, and the dementias. The case is made for further outcome studies and foundational research.

The Physical Random Access Channel (PRACH) plays an important role in LTE and LTE-A systems. It is through the PRACH channel that the user equipment (UE), based on eNodeB's timing estimates, aligns its uplink transmissions to the eNodeB's uplink and gain access to the network. One of the initial operations executed by the PRACH receiver at eNodeB side is the translation of the PRACH signal back to base band, $i.e.$, center the PRACH signal around DC. This operation is a necessary step for preamble detection and can be carried out through a time-domain frequency shift operation. Therefore, in this paper we present the hardware architecture and implementation details of a configurable and optimized FPGA-based time-domain frequency shifter. It is a hardware-efficient and accurate architecture for converting the relevant received PRACH signal into base band before further signal processing. The architecture is manly based on a customized Numerically Controlled Oscillator (NCO), which is used for generating complex exponentials employing only adders, a Look-Up Table (LUT) and plain logic resources. The main advantage of the proposed hardware architecture is that it completely eliminates the need for storing a large number of long complex exponential sequences by employing a single LUT and exploiting quarter wave symmetry of the basis waveform. Our simulation results show that the proposed customized NCO architecture provides high Spurious Free Dynamic Range (SFDR) signals using a minimal amount of FPGA resources. Moreover, the proposed architecture exhibits spur-suppression ranging from 62.13 to 153.58 dB without using Taylor Series correction.

Side-scan sonar (SSS) detection is a key method in applications such as underwater environmental security and subsea resource development. The use of acoustic images for seabed target detection has gradually become a mainstream underwater detection method. However, many existing detection approaches primarily concentrate on tracking the evolution path of optical image object detection tasks, resulting in complex structures and limited versatility. To tackle this issue, we introduce a pioneering Dual-Domain Multi-Frequency Network (D2MFNet) meticulously crafted to harness the distinct characteristics of SSS image detection. In D2MFNet, aiming at the underwater detection requirements of small scenes, we introduce a novel method for optimize and improve the detection sensitivity of different frequency ranges and propose a Multi-Frequency Combined Attention Mechanism (MFCAM). This mechanism amplifies the relevance of dual-domain features across different channels and space. Moreover, recognizing that SSS images can provide richer insights after frequency domain conversion, we introduce a Dual-Domain Feature Pyramid Network (D2FPN). By incorporating frequency domain information representation, D2FPN significantly augments the depth and breadth of feature information in underwater small datasets. Our methods are seamlessly designed for integration into existing networks, offering plug-and-play functionality with substantial performance enhancements. We have conducted extensive experiments to validate the efficacy of our proposed techniques, and the results showcase their state-of-the-art performance. MFCAM improves the mAP by 16.9% in the KLSG dataset and 15.5% in the SCTD dataset. The mAP of D2FPN was improved by 8.4% in the KLSG dataset and by 9.8% in the SCTD dataset. We will make our code and models publicly available at https://dagshub.com/estrellaww00/D2MFNet.

Channel estimation is an important module to enhance the performance of orthogonal frequency division multiplexing (OFDM) systems. However, the presence of a large amount of noise in multipath fading time-varying channels significantly affects the channel estimation accuracy and thus the recovery quality of the received signals. Therefore, this paper proposes a double-threshold (DT) channel estimation method based on adaptive frame statistics (AFS). The method first adaptively determines the number of statistical frames based on the temporal correlation of the received signals, and preliminarily detects the channel structure by analyzing the distribution characteristics of multipath sampling points and noise sampling points during adjacent frames. Subsequently, a multi-frame averaging technique is used to expand the distinction between multipath and noise sampling points. Finally, the DT is designed to better recover the channel based on the preliminary detection results. Simulation results show that the proposed adaptive frame statistics-double-threshold (AFS-DT) channel estimation method is effective and has better performance compared with many existing channel estimation methods.

The Sine-Gordon expansion method is implemented to construct exact solutions some conformable time fractional equations in Regularized Long Wave(RLW)-class. Compatible wave transform reduces the governing equation to classical ordinary differential equation. The homogeneous balance procedure gives the order of the predicted polynomial-type solution that is inspired from well-known Sine-Gordon equation. The substitution of this solution follows the previous step. Equating the coefficients of the powers of predicted solution leads a system of algebraic equations. The solution of resultant system for coefficients gives the necessary relations among the parameters and the coefficients to be able construct the solutions. Some solutions are simulated for some particular choices of parameters.

These days, numerous organizations and Analysis Centers (AC) offer various Ambiguity Resolution (AR) products using various methodologies. To use it for time-frequency transfer, there is no associated study. This paper chooses 16 MGEX stations with external high-precision atomic clocks to constitute 15 international time comparison links and uses AR products data from CNES, SGG, CODE, and PRIDE laboratory, using three ambiguity-fixed strategies, to thoroughly evaluate the effects of various strategies and AR products for high-precision time-frequency transfer. We reach the following results by using the IGS final clock product as a reference and comparing it to ambiguity-float. With various ambiguity-fixed procedures, the time stability STD of time transfer is increased for a single GPS, and the improvement ranges from 10% to 40%. The frequency stability has barely improved; up to 40%, the most notable improvement comes from FCB with GRM products. The time stability STD of combinations has improved after the addition of the Galileo system compared to the single GPS, and the improvement ranges from 2% to 9%. Most strategies have improved, while a few techniques have weakened with the GEC (GPS+Galileo+BDS) combination. We feel that the stability has not significantly increased with the system's increase within short-term stability after comparing multiple groups of linkages.

Time is a component quantity of various measurements and is also used on its own to sequence events, to compare the duration of events or the intervals between them, and to quantify rates of change of quantities in material reality or in the conscious experience [1]. The measuring equipment well might happen to be a clock. By making a presupposition that clock is Time, it is perceived experimentally that “Time exhibits wave-like properties”

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

The reactive nature of traditional frequency stability methods can lead to delayed corrective actions and unnecessary loss-of-load. This work presents a distributed model predictive control method for proactive power system frequency stability. Dynamic state estimation model is derived through a particle filter. By being able to estimate the future state of frequency, corrective actions can be taken before the system reaches a critical condition. Proactive approach makes it possible to optimize the response to a disturbance, which results in a decrease of the amount of compensation utilized. The method is tested via Matlab simulations based on Kundur's Two-Area System, and the IEEE 14-Bus system. Performance metrics are provided and evaluated against other contemporary solutions found in literature. Easy-to-derive model, without hard-to-design parameters, indicate potential towards real-life applications.

Time evolution operators of a strongly ionizing medium are calculated by a time-dependent unitary transformation (TDUT) method. The TDUT method has been employed in quantum mechanical system composed of discrete states. This method is especially helpful for solving molecular rotational dynamics in quasi-adiabatic regimes because the strict unitary nature of the propagation operator allows us to set the temporal step size large; a tight limitation on the temporal step size ($\delta t <<1$) can be circumvented by the strict unitary nature. On the other hand, in a strongly ionizing system where the Hamiltonian is not Hermitian, the same approach cannot be directly applied because it is demanding to define a set of field-dressed eigenstates. In this study, the TDUT method was applied to the ionizing regime using the Kramers-Henneberger frame, in which the strong-field-dressed discrete eigenstates are given by the field-free discrete eigenstates in a moving frame. Although the present work verifies the method for a one-dimensional atom as a prototype, the method can be applied to three-dimensional atoms, and molecules exposed to strong laser fields.

Deep Learning (DL) and Machine Learning (ML) are widely used in many fields, but rarely used in Frequency Estimation (FE) and Slope Estimation (SE) of signals. Frequency and slope estimation for Frequency-Modulated (FM) and single-tone sinusoidal signals are essential in various applications, such as wireless communications, sonar, and radar measurements. In this work, artificial neural network (ANN) and convolutional neural network (CNN) are used in frequency and slope estimation for FM signals under Additive White Gaussian Noise (AWGN) and Additive Symmetric alpha Stable Noise (SαSN). SαS distributions are impulsive noise disturbances found in many communication environments like marine systems; their distribution lacks a closed-form Probability Density Function (PDF), except for specific cases, and infinite second-order statistic, hence Geometric SNR (GSNR) is used in this work to determine the impulsiveness of noise in a mixture of Gaussian and SαS noise processes. ANN is a machine learning classifier, designed with few layers for reducing FE and SE complexity while getting higher accuracy as compared with classical techniques. CNN is a deep learning classifier, designed with many layers for FE and SE, and proved to be more accurate than ANN when dealing with big data and finding optimal features. Simulation results show that SαS noise can be much more harmful for FE and SE of FM signals than Gaussian noise. DL and ML can significantly reduce FE complexity, memory cost, and power consumption, which is important in many systems such as some Internet of Things (IoT) sensor applications. After training DCNN for frequency and slope estimation of LFM signals, the performance of DCNN (in terms of accuracy) can give acceptable results at very low signal-to-noise ratios where TFD fails, giving more than 20dB difference in the GSNR working range.

Evaluating the integrity of structures is an important issue in engineering applications. The use of vibration-based techniques has become a common approach to assessing cracks, which are the most often occurring damage in structural elements. When involving an inverse method, it is necessary to know the influence of the position and the geometry of the crack on the modal parameter changes. The geometry of the crack, both in size and shape, defines the damage severity (DS). In this study, we present a method (DS-SHC) used for estimating the DS for closed and open transverse cracks in beam-like structures by using the intact and damaged beam deflections under its weight and a Stochastic Hill Climbing (SHC) algorithm. After describing the procedure of applying DS-SHC, we calculate for a prismatic cantilever beam the severities for different crack types and depths. The results are tested by comparing the DS obtained with DS-SHC with those acquired from dynamic tests made using professional simulation software. We obtained a good fit between the severities determined in these two ways. Afterward, we performed laboratory experiments and find out that the severities obtained with the DS-SHC method can accurately predict the frequency changes due to the crack. Hence, these severities are a valuable tool for damage detection.

This paper first introduces the main classification of brain diseases and the main causes of these diseases. It is followed by wavelet analysis, which is a mathematical function or wave-like pattern used to transform data, which can decompose the signal into different wavelet functions, each of which is related to a specific scale or frequency. Wavelet analysis has been applied in many fields such as image processing, data analysis and engineering. In addition, wavelet is also used in the analysis of biological signals. Wavelet analysis breaks down brain signals, such as EEG or fMRI data, into various frequency components at different scales. Wavelet analysis provides time-frequency localization. Pattern recognition can be enhanced by isolating salient features in the data. Wavelet denoising can effectively separate noise from underlying brain signals. Wavelet denoising usually adopts threshold method. Wavelet analysis can enhance pattern recognition by isolating salient features in the data. Researchers can train machine learning models based on these wavelet-derived features to recognize specific patterns associated with different neurological disorders. Wavelet analysis can track these changes by continuously evaluating the frequency content of the neuroimage data over time. Through continuous efforts, wavelet theory and technology have become valuable tools in the field of neuroscience and brain disease research.

Improving the acquisition and retention of a new motor skill is of great importance. The present study (i) investigated the effects of difficulty manipulation strategies (gradual difficulty), combined with different modalities of feedback (FB) frequency on performance accuracy and consistency when learning a novel fine motor coordination task, and (ii) examined relationships between novel fine motor task performance and executive function (EF), working memory (WM), and perceived difficulty (PD). Thirty-six, right-handed, novice physical education students volunteered to participate in this study. Participants were divided into three progressive difficulty groups (PDG), 100% visual FB (FB1), 50% FB (FB2), and 33% FB (FB3). Progressive difficulty was increased by the manipulation of the distance to the target; 2 m, 2.37 m, and 3.56 m. Three FB modalities were investigated (i.e.: 100% visual FB (100% FB), 50% reduced feedback condition (50% RFB), and 33% reduced feedback conditions (33% RFB)). Performance assessments were conducted following familiarization, acquisition, and retention learning phases. Two stress-conditions of dart throws were investigated (i.e.: free condition (FC) and time pressure condition (TPC)). After the learning intervention, data showed that, under the free condition, the 100% FB group had a significant improvement in accuracy during all learning phases. Under time pressure condition, for the 50% RFB and the 33% RFB group, the measured variable (accuracy and consistency) showed a significant linear improvement in performance. The association between the percentage of RFB frequencies and the task difficulty (50% group) may be a more appropriate and manageable cognitive load compared to the 33% RFB and the 100% FB group. The present findings could have practical implications for practitioners because, while strategies are clearly necessary for improving learning, the efficacy of the process appears to be essentially based on the characteristics of the learners.

In the present work, a novel conductive liquids method of study has been proposed. It is based on the phenomenon of radiofrequency anisotropy of electrolyte solution discovered by us. It arises in response to mechanical or acoustic excitation of the solution. We have observed the phenomenon during the development of an RF polarimetric contactless cardiograph. The electric field vector of the transmitted 433.82 MHz signal rotated after its transition through the pericardial region. That rotation depends on the change of blood acceleration when passing through the chambers of the heart and large vessels. It has also been revealed that rotation occurs after RF wave passage through the physiological saline (0.9% NaCl) subjected to any mechanical excitation inside it like a jet appearing or soundwave passing. No significant difference was detected experimentally between NaCl and KCl solutions behavior. It means that the mechanism of hydrodynamic separation of ions is apparently not suitable to explain the phenomenon. The response we have registered resembles the magnetization process of spin glasses. From the nature of the observed response, we have concluded that a fundamentally new physical effect is discovered. It may provide wide opportunities for remote measurement of the electrolyte solution parameters with polarized radio-frequency signals.

In this paper, the physical station of space network was extended in time dimension by combining the train diagram information and station technical operation standard time. At the same time, the topology of railway space-time network which considered the secondary operation process of train was constructed and an improved A* algorithm based on car flow routing was proposed to generate feasible path sets. On this basis, a dynamic car flow organization optimization model was built to simulate the railway car flow organization process under abnormal conditions, and the results of solving the model could be used to obtain the real-time quantity of cars at each station.This paper can identify the dynamic bottleneck by comparing the real-time quantity of cars with the maximum quantity of cars at the station. Finally, the feasibility of this method was analyzed and verified by a case.

The International Maritime Organization (IMO) is enforcing increasingly stringent regulations on ship carbon emissions, The International Maritime Organization (IMO) has been implementing progressively strict regulations on ship carbon emissions, leading to the adoption of the virtual arrival (VA) method by many vessels to reduce their carbon footprint. However, the effectiveness of the traditional VA method often varies in busy ports with complex traffic organization scenarios. To address this, our study presents a novel, comprehensive model that integrates vessel scheduling with the VA approach. This model is designed to achieve a dual objective: reducing carbon emissions through Virtual Arrival and simultaneously minimizing vessel waiting times. In addition to these goals, it incorporates essential aspects of safety, efficiency, and fairness in port management, utilizing the NSGA-2 algorithm to find optimal solutions. This model has been tested and validated through a case study at Ningbo-Zhoushan port, employing its dataset. The results demonstrate that our innovative model and algorithm significantly outperform traditional scheduling methods, such as First-Come-First-Serve (FCFS) and Virtual-Arrival Last-Serve (VALS), particularly in terms of operational efficiency and reduction in vessel carbon emissions.

This paper propose an original approach of achieving a Cymatics based visual perception of isolated speech commands. The idea is to smartly combine the effective speech processing and analysis methods with the phenomena of Cymatics. In this context, an effective approach for automatic isolated speech based message recognition is proposed. The incoming speech segment is enhanced by applying the appropriate pre-emphasis filtering, noise thresholding and zero alignment operations. The Mel-Frequency Cepstral coefficients (MFCCs), Delta coefficients and Delta-Delta coefficients are extracted from the enhanced speech segment. Later on, the Dynamic Time Warping (DTW) technique is employed to compare these extracted features with the reference templates. The comparison outcomes are used to make the classification decision. The classification decision is transformed into a methodical excitation. Finally, this excitation is converted into the systematic visual perceptions via the phenomenon of Cymatics. The system functionality is tested with an experimental setup and results are presented. The approach is novel and can be employed in various applications like visual art, encryption, education, archeology, architecture, integration of impaired people, etc.

The Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost deviations using proprietary T/S and T/C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

Since the come up in the 70´s, various decentralized control methodologies have been developed to deal with the challenge of controlling complex and/or spatially distributed systems with multiple inputs and multiple outputs (MIMO), e.g., chemical plants, power systems, water systems, etc. In general, the use of distributed information and control structures requires to synthesize control laws in a constrained (decentralized) information structure. The article presents another version of the unified frequency domain robust decentralized controller design method [1]. The proposed design procedure is appropriate for uncertain dynamic MIMO systems given as a set of transfer function matrices. Its main framework is provided by the Equivalent Subsystems Method [1, 24] guaranteeing fulfillment of the necessary and sufficient stability condition of the overall closed-loop system if individual closed-loop equivalent subsystems are stable. Generating sets of equivalent subsystems for all transfer function matrices describing the uncertain MIMO plant allows to use the QFT method [19] to independently design local robust SISO controllers that constitute the resulting decentralized controller implemented on true subsystems. The developed design procedure is verified and illustrated on a case study on robust decentralized level controller design for a quadruple tank process [2, 24].

The article presents a new approach to the analysis of the stability of automatic systems with discrete links.In almost all modern automatic control systems, there are links that break signals in time. These are power controlled switches - transistors or thyristors operating in a pulsed mode and digital links in regulators.Time discretization significantly affects the stability of processes in the automatic control system. The theoretical analysis of such systems is rather complicated and requires a significant change in engineering approaches to analysis. In connection with the improvement of digital controllers and a significant increase in their performance, in recent years this problem has practically not been remembered. However, its mathematical "content" has not changed since the 80s of the 20th century, when discreteness began to play a major role among the problems hindering progress in automatic control systems, in terms of the transition to digital systems.In this paper, a new approach is proposed, which consists in interpreting the sampling operation by a link with the proposed frequency characteristic, which determines the suppression of input high-frequency signals. This link greatly simplifies engineering calculations and demonstrates the new capabilities of sampling systems. These possibilities include the rational distribution of digitalization resources - the number of bits and the sampling interval between the regulator channels, depending on the frequency range of the efficiency of these channels. Theoretical statements have been verified and confirmed by simulation. It is shown how this approach makes it possible to formulate new principles of construction of seemingly well-known controllers - PID controllers and variable structure systems (VSS).

In this study, we present a numerical method for solving two--dimensional space--time fractional partial differential equations (FPDEs), where the solutions of the FPDEs are expanded in terms of the shifted Chebyshev polynomials. The numerical approximations are evaluated at the Chebyshev-Gauss-Lobatto points. In the case when the FPDE is nonlinear, we employ a Newton-Raphson approach to linearize the equation. Both the linear and nonlinear cases lead to a consistent system of linear algebraic equations. The scheme is tested on selected FPDEs and the numerical results show that the proposed numerical scheme is accurate and computationally efficient in terms of CPU times. To establish the accuracy of the method, we also present an error analysis which shows the convergence of the numerical method. These positive attributes make the proposed method a good approach for solving two--dimensional fractional partial differential equations with both space and time fractional orders.

The aim of this paper is to introduce a new methodology for the fault diagnosis of induction machines working in transient regime, when time-frequency analysis tools are used. The proposed method relies on the use of the optimized Slepian window for performing the short time Fourier transform (STFT) of the stator current signal. It is shown that for a given sequence length of finite duration the Slepian window has the maximum concentration of energy, greater than can be reached with a gated Gaussian window, which is usually used as analysis window. In this paper the use and optimization of the Slepian window for fault diagnosis of induction machines is theoretically introduced and experimentally validated through the test of a 3.15 MW induction motor with broken bars during the start-up transient. The theoretical analysis and the experimental results show that the use of the Slepian window can highlight the fault components in the current's spectrogram with a significant reduction of the required computational resources.

Anomaly detection plays a significant role in helping gas turbines run reliably and economically. Considering collective anomalous data and both sensitivity and robustness of the anomaly detection model, a sequential symbolic anomaly detection method is proposed and applied to the gas turbine fuel system. A structural Finite State Machine is to evaluate posterior probabilities of observing symbolic sequences and most probable state sequences they may locate. Hence an estimating based model and a decoding based model are used to identify anomalies in two different ways. Experimental results indicates that these two models have both ideal performance overall, and estimating based model has a strong ability in robustness, while decoding based model has a strong ability in accuracy, particularly in a certain range of length of sequence. Therefore, the proposed method can well facilitate existing symbolic dynamic analysis based anomaly detection methods especially in gas turbine domain.

In today’s world face detection is the most important task. Due to the chromosomes disorder sometimes a human face suffers from different abnormalities. For example, one eye is bigger than the other, cliff face, different chin-length, variation of nose length, length or width of lips are different, etc. For computer vision currently this is a challenging task to detect normal and abnormal face and facial parts from an input image. In this research paper a method is proposed that can detect normal or abnormal faces from a frontal input image. This method used Fast Fourier Transformation (FFT) and Discrete Cosine Transformation of frequency domain and spatial domain analysis to detect those faces.

In the study, a new correction method was applied to reduce error during detection on mixed pesticide residue in apples by using Raman spectra. Combined with self-built pesticide residues detection system by Raman spectroscopy and the application of surface enhancement technology, rapid real-time qualitative and quantitative analysis of deltamethrin and acetamiprid residues in apples can be applied effectively. In quantitative analysis, compared with the intensity value of characteristic peaks of single pesticide with same concentration, the intensity value of characteristic peaks of the two pesticides decreased after mixing the pesticides, which interferes the results severely. By comparing the difference in the intensity of characteristic peaks of single and mixed pesticides, a correction method is proposed to eliminate the influence of pesticides mixture. Characteristic peak intensity values of gradient concentration pesticide from 10-1 g•kg-1 to 10-6 g•kg-1 and Lagrangian interpolation are applied in the correction method. And a smooth surface is applied to describe the correction ratio of characteristic peak intensity. Through detecting the characteristic peak intensity values of the mixed pesticide, correction ratio will be obtained. Then real values of the peak intensity of pesticides and the content of each component of the mixed pesticide will be acquired by the correction method. Correlation coefficient of model validation exceeds 0.88 generally and Root Mean Square Error also decreases obviously after correction, which proved the reliability of the method.

After proposing a natural metric for the space in which particles spin which implements the principle of maximum frequency, E=hf is generalised and its inverse Fourier transform is calculated. As a necessary result, a metric is found for the space in which quantum particles spin, hence the possibility of explanation of correlation of spacelike-separated particles is opened up.

This article examines the impact of some system parameters on an industrial system composed of two dissimilar parallel units with one repairman. The active unit may fail due to essential factors like aging or deteriorating, or exterior phenomena such as Poisson shocks that occur at various time periods. Whenever the value of a shock is larger than the specified threshold of the active unit, the active unit will fail. The article assumes that the repairman has the right to take any of two decisions at the beginning of the system operation: either a takes a vacation if the two units work in a normal way, or stay in the system to monitor the system until the first system failure. In case of having a failure in any of the two units during the absence of the repairman, the failing unit will have to wait until the repairman is called back to work. We suppose that the value of every shock is assumed to be i.i.d. with some known distribution. The length of the repairman’s vacation, repair time, and recall time are arbitrary distributions. Various reliability measures have been calculated by the supplementary variable technique and the Markov’s vector process theory. At last, numerical computation and graphical analysis have been given for a particular case to validate the derived indices.

Maxwell equation for the electric field has been solved for any medium by suggesting the wavenumber and angular frequency be complex quantities. This accounts for the field decay by interaction with the medium.This expression for the time and special decay of the electric field in a medium is used to construct a new wave function sensitive to the medium physical properties. This new wave function, unlike the conventional one, differentiates between a beam of particles in a vacuum and that enters a medium which is an attenuated due to the scattering effect.Another expression for time decaying electric field was obtained using Newton’s laws for frictional medium. This expression shows that the electric field diminishes due to friction.Fortunately, this time decaying part of the electric field is typical to that derived from Maxwell’s equations. Finally, a new Schrodinger equation sensitive to the medium properties was derived. This equation, fortunately, describes some scattering processes for Protein scattering, scattering of x-rays, opto-acoustic phonons, and Raman scattering for some materials successfully .

The three dimensional conformable time fractional Kadomtsev-Petviashvili and the conformable time fractional modified Kawahara equations are solved by implementing the Kudryashov's procedure. The corresponding wave transformation reduces both equations to some ODEs. Balancing the nonlinear and the highest order derivative terms gives the structure of the solutions in the finite series form. The useful symbolic tools are used to solve the resultant algebraic systems. The solutions are expressed in explicit forms.

Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost variances using proprietary C-S and S-C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

For the problem of poor accuracy of the existing multi-rate simulation methods, this paper proposes a multi rate real-time simulation method based on the Norton equivalent, compared with multi-rate simulation method based on the ideal source equivalent. After the Norton equivalence of the fast subsystem and the slow subsystem, they are obtained simultaneously at the junction nodes. In order to reduce the amount of simulation calculation, the Norton equivalent circuit is obtained by incremental calculation. The data interface between the fast subsystem and the slow subsystem is realized by extrapolation method. For ensuring the real-time performance of the simulation, the method that the slow subsystem calculates ahead of the fast subsystem is given for the slow subsystem with a large amount of calculation. Finally, the AC/DC hybrid power system was simulated on the real-time simulation platform (FRTDS), and the simulation results were compared with the single-rate simulation, which verified the correctness and accuracy of the method.

In Korea, the underground silo structure for low- and intermediate-level radioactive waste disposal facilities has been constructed and operated since 2014. Large-scale earthquakes occurred in 2016 and 2017, respectively, in Gyeongju and Pohang areas near the underground silo structures, and interest in the stability of the underground silo increased significantly. In this paper, one-dimensional free field analyses have been carried out before the three-dimensional silo dynamic analyses subjected to earthquake loadings. As an additional study, a new form of finite element equilibrium equation is derived in terms of relative motions, which is essentially the same equation as that expressed in terms of total motions where the base shear force is applied for earthquake load. The accuracy of conventional finite element solutions is evaluated by directly comparing them with closed-form solutions by frequency domain analysis such as SHAKE91.

In this paper, initially a mathematical model is formulated for transient frequency of power system considering time delays which occur while transmitting the control signals in open communication infrastructure. Time delay negligence in a power system leads to improper measurement of frequency variation in power system. The study of impact of time delays on the stability of power system is performed by estimating the decay rate of frequency wave form using Kalman Filter (KF). In power system, there is a possibility of multiple time delays. This paper also focusses on developing Interacting Multiple Model (IMM) Algorithm with multiple model space using Kalman Filter (KF) as state estimator tool. The multiple time delays in power system is considered as multiple model space. The result shows that KF provides better estimate of correct model for a particular input-set. The qualitative properties of Riccati difference equation (RDE) in terms of state error covariance of IMMKF are also analyzed and presented.

The present study analyzed the effect of temperature, pH, retention time, pretreatment and mixing ratio on the anerobic digestion process. The parameters during the anaerobic co digestion of cow manure and food waste were then optimized using the Taguchi experimental design method. ANOVA is carried out to find the significant parameters which influence the biogas production. Experimental tests were carried out at laboratory scale reactors kept at different temperatures (28 °C, 35 °C, and 50 °C). The specific methanogenic Performance (SMP) during anerobic digestion at higher temperatures was characterized with the analysis of acetate, propionate, butyrate, hydrogen, glucose, and formate. The improvement of biogas production with different pre-treatment i.e., ultrasonic, autoclave, and microwave techniques also analysed. The results showed that reactor that maintained at 35 °C showed the highest biogas production. While the reactor that maintained at lower temperature (28 °C) produced the lower volume of biogas. As the retention time increases, the amount of biogas produced increases. Methanogenic activities of microorganisms reduced at higher temperature conditions (65 °C). Biogas production increased by 28.1%, 20.23%, and 13.27 % when the of substrates treated with ultrasonic, autoclave, and microwave, respectively, compared to the untreated substrate. The optimized condition for the highest biogas production during anaerobic co digestion of food waste and cow manure is temperature of 35 °C, pH of 7 and mixing ratio (CM: FW=1.5:0.5). ANOVA showed that temperature is the most important input parameter affecting biogas production, followed by mixing ratio.

Printed electronic devices are attracting significant interest due to their versatility and low cost; however, quality control during manufacturing is a significant challenge, preventing the widespread adoption of this promising technology. We show that terahertz (THz) radiation can be used for the in situ inspection of printed electronic devices, as confirmed through a comparison with conventional electrical conductivity methods. Our in situ method consists of printing a simple test pattern exhibiting a distinct signature in the THz range that enables the precise characterization of {the static} electrical conductivities of the printed ink. We demonstrate that contactless dual-wavelength THz spectroscopy analysis, which requires only a single THz measurement, is more precise and repeatable than the conventional four-point probe conductivity measurement method. Our results open the door to a simple strategy for performing contactless quality control in real time of printed electronic devices at any stage of its production line.

Determination of indoor location based on fine time measurement (FTM) of the round trip time (RTT) of a signal between an initiator (smartphone) and a responder (Wi-Fi access point) enables a number of applications. However, the accuracy currently attainable — standard deviations of 1–2 meter in distance measurement under favorable circumstances — limits the range of possible application. A first responder, for example, may not be able to unequivocally determine on which floor someone in need of help is in a multi-story building. The error in location depends on several factors, including the bandwidth of the RF signal, delay of the signal due to the high relative permittivity of construction materials, and the geometry-dependent “noise gain” of location determination. Errors in distance measurements have unusual properties that are exposed here for the first time. Improvements in accuracy depend on understanding all of these error sources. This paper introduces “frequency diversity,” a method for doubling the accuracy of indoor location determination using weighted averages of measurements with uncorrelated errors obtained in different channels. The properties of this method are verified experimentally with a range of responders. Finally, different ways of using the distance measurements to determine indoor location are discussed and the Bayesian grid update method shown to be more useful than others, given the non- Gaussian nature of the measurement errors.

Modern computational biology makes widespread use of mathematical models of biological systems, in particular systems of ordinary differential equations, as well as models of dynamic systems described in other formalisms, such as agent-based models. Parameters are numerical values of quantities reflecting certain properties of a modeled system and affecting model solu-tions. At the same time, depending on parameter values, different dynamic regimes - stationary, oscillatory, established as a result of transient modes of various types - can be implemented in the system. Predicting changes in the solution dynamics type depending on changes of model parameters is an important scientific task. Nevertheless, this problem does not have an analytical solution for all formalisms in a general case. The routinely used method of performing a series of computa-tional experiments, i.e. solving a series of direct problems with various sets of parameters fol-lowed by expert analysis of solution plots is labor-intensive with a large number of parameters and a decreasing step of the parametric grid. In this regard, the development of methods allow-ing to obtain and analyze information on a set of computational experiments in an aggregate form is relevant. This work is devoted to developing a method for visualization and classification of various dy-namic regimes of a model using a composition of the dynamic time warping (DTW-algorithm) and principal coordinates analysis (PCoA) methods. This method allows to obtain a qualitative visualisation of the results of the set of solutions of a mathematical model and to carry out the correspondence between the values of the model parameters and the type of dynamic regimes of its solutions. This method has been tested on the Lotka-Volterra model and artificial sets of var-ious dynamics

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

Peanut (Arachis hypogaea) contains allergenic proteins, which make it harmful to the sensitised population. The presence of peanut in foods must be indicated on label, to prevent accidental consumption by allergic population. In this work, we use chloroplast markers for specifically detection of peanut by real-time PCR, in order to increase the assay sensitivity. Binary mixtures of raw and processed peanut flour in wheat were performed at concentrations ranging from 100000 to 0.1 mg/kg. DNA isolation from peanut, mixtures and other legumes was carried out following three protocols for obtaining genomic and chloroplast-enrich DNA. Quantity and quality of DNA was evaluated, obtaining better results for protocol 2. Specificity and sensitivity of the method has been assayed with specific primers for three chloroplast markers (mat k, rpl16 and trnH-psbA) and Ara h 6 peanut allergen-coding region was selected as nuclear low-copy target and TaqMan probes. Efficiency and linear correlation of calibration curves were within the adequate ranges. Mat k chloroplast marker yielded the most sensitive and efficient detection for peanut. Moreover, detection of mat K in binary mixtures of processed samples was possible up to 10 mg/kg even after boiling, and autoclave 121°C 15 min, with acceptable efficiency and linear correlation. Applicability of the method has been assayed in several commercial food products.

Since its initial development in the 1970’s by Phil Burke and his collaborators, the R-matrix theory and associated computer codes have become the de facto approach for the calculation of accurate data for general electron-atom/ion/molecule collision and photoionization processes. The use of a non-orthonormal set of orbitals based on B-splines, now called the B-spline R-matrix (BSR) approach, was pioneered by Zatsarinny. It has considerably extended the flexibility of the approach and improved particularly the treatment of complex many-electron atomic and ionic targets, for which accurate data are needed in many modelling applications for processes involving low-temperature plasmas. Both the original R-matrix approach and the BSR method have been extended to the interaction of short, intense electromagnetic (EM) radiation with atoms and molecules. Here we provide an overview of the theoretical tools that were required to facilitate the extension of the theory to the time domain. As an example of a practical application, we show results for two-photon ionization of argon by intense short-pulse extreme ultraviolet radiation

One of the challenges posed by renewable energies is the stabilization of parameters related to the quality of electrical energy. This study demonstrates the existence of a relationship between input blocks of hydropower and the variation of the fundamental frequency of the electricity grid. By mapping production data provided by Spanish Electric Network with frequency measured in the laboratory, it is shown that gradients of hydropower are correlated with frequency fluctuations for certain characteristic times. Considering hourly instances of energy input, the study compares two methods for calculating hydropower gradients (linear regression and pseudo-linear regression); and two methods for calculating local frequency extremes (the "specular inertia" method and analysis by comparison with the moving average), in order to corroborate the results.

Spinal muscular atrophy 5q (SMA) is the most common neuromuscular inherited disease in neonates which is associated with homozygous deletion of exon 7 in the SMN1 gene. Recently established drugs can improve the motor functions of SMA infants when treated in the pre-symptomatic stage. With aim of providing an early diagnosis, newborn screening (NBS) for SMA using real-time PCR assay with dried blood spots (DBS) was performed in Saint-Petersburg from January 2022 through November 2022. Here, 36,140 newborns were screened by GenomeX real-time PCR-based screening test, and three genotypes were determined. Homozygous deletion carriers (4 newborns), heterozygous carriers (772 newborns) and wild-type individuals (35,364 newborns) were identified. All four newborns screened positive for homozygous SMN1 deletion were confirmed by alternate methods. Two of the newborns had two copies of SMN2, and two of the newborns had three copies. We determined Saint-Petersburg spinal muscular atrophy incidence of 1 in 9,035 and SMA carrier frequency of 1 in 47. In conclusion, it can be summarized that providing both timely SMN1 information and confirmation along with SMN2 copy number as part of SMA newborn screening algorithm can significantly improve clinical follow-up, family members testing, and SMA patients' treatment.

Conventional mechanical Fourier Transform Spectrometers (FTS) are able to simultaneously measure absorption and dispersion spectra of gas-phase samples. However, they usually need very long measurement times to achieve time-resolved spectra with a good spectral and temporal resolution. Here, we present a mid-infrared dual-comb-based FTS in an asymmetric configuration, providing broadband absorption and dispersion spectra with a spectral resolution of 5 GHz, a temporal resolution of 20 μs, and a total measurement time of a few minutes. We used the dual-comb spectrometer to monitor the reaction dynamics of methane and ethane in an electrical plasma discharge. We observed ethane/methane formation as a recombination reaction of hydrocarbon radicals in the discharge in various static and dynamic conditions. The results demonstrate a new analytical approach for measuring fast molecular absorption and dispersion changes and monitoring fast dynamics of chemical reactions, which can be interesting for chemical kinetic research and particularly for the combustion and plasma analysis community.

Cloud computations are based on the computer networks such as Internet which presents a new pattern to provide, consume and deliver services such as infrastructure, software, ground and other resources using network. The inappropriate timing of assigning loads to the virtual machines in the computational space could lead to unbalance in the system. One of the challenging planning problems. In the cloud data centers is considering both assigning and migration (transfer) of the virtual machines with the ability of reconfiguration and the integrated features of the hosting physical machines. In this article, we introduce an integrated and dynamic timing algorithm based on the Genetic evolution algorithm. The suggested method was evaluated based on these factors and different inputs. Our suggested method is done using Java programming language and cloud-SME simulation. The results show that the execution time and the response time were improved by 12 and 1 percent respectively.

: In this article, the authors propose an algorithmic approach to building a model of the dynamics of economic and, in particular, innovation processes. The approach under consideration is based on a complex algorithm that includes (1) decomposition of the time series into components using singular spectrum analysis; (2) recognition of the optimal component model based on fuzzy rules, and (3) creation of statistical models of individual components with their combination. It is shown that this approach corresponds to the high uncertainty characteristic of the tasks of the dynamics of innovation processes. The proposed algorithm makes it possible to create effective models that can be used both for analysis and for predicting the future states of the processes under study. The advantage of this algorithm is the possibility to expand the base of rules and components used for modeling. This is an important condition for improving the algorithm and its applicability for solving a wide range of problems.

This study aims to estimate the scientific productivity of collective subjects. The objective is to build a method for evaluating scientific productivity that allows calculating productivity, including for new collective subjects with a small citation network—the paper purposes the Time-Weighted PageRank method with citation intensity (TWPR-CI). The Citation Network Dataset (ver. 13) has been analyzed to verify the method. The dataset includes more than 5 million scientific publications and 48 million citations. There have been allocated four classes of collective subjects (more than 27,000 collective subjects in total). For each class, scientific productivity estimates from 2000 to 2021 were calculated using the PageRank, Time-Weighted PageRank, and TWPR-CI methods. It is shown that the advantage of the TWPR-CI method is the higher sensitivity of the scientific productivity estimates for new collective subjects on average during the first ten years of observation. At the same time, the assessment of scientific productivity for other collective subjects according to this method is stable. However, the small citation network of the new collective subjects does not allow an adequate assessment of scientific productivity during the first years of its operation. Therefore, the TWPR-CI method can be used to assess the scientific productivity of collective subjects, in particular the productivity of new ones.

That how to improve the sensitivity and the detection ability of the Large-caliber sensor is critical to satisfy the requirement of heavy vehicle wear condition monitoring. In this paper, we introduced the LC resonance principle to the design of sensor with large flow channel (7mm). The resonant exciting coil increases the impedance change of the exciting circuit caused by wear particles which magnify the current difference between the two exciting coils and improve the sensitivity of the sensor. The resonant induction coil greatly suppresses the interference signals and magnifies the weak induced electromotive force which is beneficial to enhance the detection ability. In order to boost the detectability for different materials particles, a phase controlled variable-frequency exciting system (PCVFES) was adopted to automatically switch the exciting frequency between 284kHz for ferromagnetic particles and 420KHz for non-ferromagnetic particles. For the weak signal detection, based on the essential characteristic of the signal, we apply a simpler method that modified lock-in amplifier (MLIA) rather than the conventional algorithms (Wavelet transform, EMD). Results show that using these methods the sensitivity and the detection ability of the sensor are significantly improved and the 75μm iron particles and 220μm copper particles were successfully detected which realizes the initial abnormal wear monitoring for the large flow project.

Satellite communication (Satcom) is an artificial geostationary satellite that facilitates a wide range of telecommunications. Considering its quality of service (QoS) and security is crucial in government/military applications. The most challenging situation for efficient Satcom is radio frequency interference (RFI) environment. Thus, it is necessary to ensure that transmissions are incorruptible or at least sense the quality of its spectrum. This paper presents a new method to recognize received signal characteristics using a hierarchical classification in a multi-layer perceptron neural network. We consider signal modulation and the type of RFI as the characteristics of a real-time video stream transmitted in the direct broadcast satellite. Four different modulation types are investigated in this study. Moreover, the combination of the communication signal with various kinds of interference and their effects on the classification method widely have been analyzed. Besides, two robust feature selection techniques have been developed to reduce the data-set dimensional, which leads to optimizing the classification process. The results show that the Genetic Algorithm (GA) slightly outperforms Principal Component Analysis (PCA) for feature selection. Furthermore, the robustness of the proposed techniques is assessed to detect unknown signals at different signal to noise ratios.

This letter introduces a frequency response characteristic (FRC) curve and its application in high renewable power systems. In addition, the letter presents a method for fast frequency response assessment and frequency nadir prediction without performing dynamic simulations using detailed models. The proposed FRC curve and fast frequency response assessment method are useful for operators to understand frequency response performance of high renewable systems in real time.

This paper presents a 612–1152 MHz Injection Locked Frequency Multiplier (ILFM). The proposed ILFM is only used for sending an input signal to the receiver in the I/Q mismatch calibration mode. Using the Phase-Locked Loop (PLL) to calibrate the receiver places a burden on this system due to the extra area required and power consumption. Instead of the PLL, to satisfy high frequency, low jitter, and low area, a Ring Oscillator is proposed. The free-running frequency of the ILFM is automatically digitally calibrated to reflect the frequency of the injected signal from the harmonics of the reference clock. To control the frequency of the ILFM, the load current is digitally tuned with 6-bit digital control signal. The proposed ILFM locks to the target frequency using a digitally controlled Frequency Locked Loop (FLL). This chip is fabricated using 1-poly 6-metal 0.18 µm CMOS and achieve the wide tuning range of 612–1152 MHz. The power consumption is 0.95 mW from a supply voltage of 1.8 V. The measured phase noise of the ILFM is −108 dBc/Hz at a 1 MHz offset.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

The sTetro is a stair cleaning robot which can climb the staircase with its shapeshifting capabilities. As this robot is intended to traverse multi-floor environment autonomously, hence its localization/positioning information is an essential component of the overall system. Usually, the indoor mobile robots rely on some external system for localization information, e.g., WiFi, UWB, vision, RFID signals, or indoor Global Positioning System (GPS). This requires the installation of additional hardware and/or modification of the working environment for precise positioning information of the mobile platform. As the dimensions of the staircase are known a priori, this knowledge can be used to localize the sTetro robot on the stairs. In this article, the geometry of the staircase has been exploited to localize the robot in 3D space with measurements from the onboard time-of-flight (ToF) range sensors only. The heading angle of the robot is also estimated with two ToF sensors installed in front of the sTetro robot. Results achieved by conducting experiments on real robot prove the efficacy of the proposed approach.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

Alzheimer's Disease (AD) is a neurodegenerative disease that is common in the elderly. This paper introduces the overview of Alzheimer's disease and the application of relevant signal processing methods in its detection. Signal processing is a technique that converts raw data into meaningful information and is widely used in the medical field. This paper lists common signal processing techniques, including Fourier transform, time-frequency analysis and statistical signal processing, and discusses their applications in the detection of Alzheimer's disease. Fourier transform can convert time domain signals into frequency domain representations, providing an effective tool for the study of EEG in Alzheimer's disease. Time-frequency analysis can perform a combined time and frequency analysis of the signal to help detect the signal characteristics of Alzheimer's disease. Statistical signal processing methods can be used to identify the features of Alzheimer's disease by building mathematical models. Finally, the challenges of Alzheimer's disease detection are discussed, including signal noise, diversity, and insufficient data volume. Through in-depth research and development of signal processing methods, it is expected to improve the accuracy and efficiency of early detection of Alzheimer's disease.

The aerospace industry develops prognosis and health management algorithms to ensure better safety on board. Particularly for in-flight controls where jamming is dreaded. For that, vibration signals are monitored to predict future defect occurrences. However, time series are not labeled according to severity level, and the user can only assess the system health from the data mining procedure. To that extent, we developed a clustering algorithm using a deep neural network core. We encoded the time series into pictures to be feed into an artificially trained neural network: U-NET. From the segmented output, one-dimensional information on cluster frontiers is extracted and filtered without any parameter selection. Then, a kernel density estimation finally transforms the signal into an empirical density. Ultimately, a Gaussian mixture model extracts the latter independent components. The method empowered us to reveal different degrees of severity faults in the studied data, with their respective likelihood without prior knowledge. We compared it to state-of-the-art machine learning algorithms. However, internal clustering results evaluation for time series is an open question. As state-of-the-art indexes were not producing relevant results, we built a new indicator to fulfill this task. We applied the whole method to an actuator consisting of an induction machine linked to a ball screw. This study lays the groundwork for future training of diagnosis and prognosis structures in the health management framework.

The article presents the original derivation method of transformations for kinematics with a universal reference system. This method allows to derive transformations that meet the results of the Michelson-Morley and Kennedy-Thorndike experiments only in some frame of reference, e.g. in laboratories moving in relation to a universal frame of reference with small speeds. The obtained transformations are the basis for the derivation of the new physical theory, which has been called the Special Theory of Ether. The generalized transformations can be expressed by relative speeds (26)-(27) or by the parameter δ (v) (37)-(38). Based on conclusions of the Michelson-Morley’s and Kennedy-Thorndike’s experiments, the parameter δ (v) was determined. This allows the transformations to take a special form (81)-(82), which is consistent with experiments in which velocity of light is measured. On the basis of obtained transformations, the formulas for summing speed and relative speed were also determined. The entire article includes only original research conducted by its author.

A nonlinear MEMS multimass sensor is investigated. The MEMS design consists of an array of nonlinear microcantilevers clamped to a shuttle mass which, in turn, is attached to a linear spring and a dashpot. The microcantilevers are made of a polymeric hosting matrix reinforced by aligned carbon nanotubes (CNT) with different CNT volume fractions in each cantilever so as to suitably tune the frequency bandwidth of the device. The advantages of a single input-single output (SISO) system are here exploited for the design, actuation and detection principles as in previous literature.

Accurately predicting electrical signals of three-phase Direct Torque Control (DTC) induction motors is crucial for optimal motor performance and effective condition monitoring. However, multiple DTC motors’ complexity and operating conditions’ variations pose challenges for traditional prediction methods. To overcome these challenges, we propose an innovative approach that combines Fast Fourier Transform (FFT) to transform electrical motor simulation data and a Bi-directional Long Short-Term Memory (Bi-LSTM) network to forecast processed motor data. By transforming the DTC induction motor signals from the time domain to the frequency domain, we enhance the capability of learning models to capture subtle differences and generate various input features. The Bi-LSTM model effectively captures both forward and backward dependencies in time series data, enabling accurate prediction of electrical signals. We evaluate the proposed approach using our simulated dataset and compare the proposed method to a state-of-the-art model, the Gated Recurrent Unit (GRU), demonstrating its effectiveness in improving the accuracy and reliability of induction motor signals forecasting. The finding provides valuable insights for advancing motor control and operation in industrial applications.

Hybrid forecasting methods have emerged as a solution surpassing the limitations of both statistical and deep learning approaches. While the first emphasize the significance of variables, they often produce worse forecasting results when compared to newer techniques. In contrast, deep learning models remain enigmatic "black boxes" in terms of interpretability, although achieving better results in forecasting. This article introduces the Comprehensive Cross-Correlation and Lagged Linear Regression Deep Learning (CCLR-DL) framework, designed to harness the best of both approaches, enhancing forecasting accuracy while retaining model interpretability through a feature selection process. CCLR-DL blens cross-correlation analysis, lagged multiple linear regression and granger's causality procedures with deep learning architectures based on LSTM. In a practical demonstration, CCLR-DL was applied to a real database of clinical visits associated to diagnoses in Catalonia, Spain (tracking a population of 6.3 million patients during 10 years). Predicting visits enables the healthcare managers to be ready for future demand shifts. Results demonstrate a consistent and substantial improvement over standalone statistical and deep learning methods when predicting healthcare demand. This hybrid approach not only showcases its efficacy but also offers a promising solution to the challenge of balancing predictive accuracy with model explicability. In this context, this work aims to design and validate a method for feature selection and forecasting of multivariate high dimensional time series datasets not only to improve prediction accuracy but also to model transparency by identifying a subset of variables that improve predictions and G-cause the target variable.

In this paper, the problem of observer-based adaptive sliding mode control is discussed for nonlinear systems with sensor and actuator faults. The time-varying actuator degradation factor and external disturbance are considered in the system simultaneously. In this study, the original system is described as a new normal system by combining the state vector, sensor faults and external disturbance into a new state vector. For the augmented system, a new sliding mode observer is designed, where a discontinuous term is introduced such that the effects of sensor and actuator faults and external disturbance will be eliminated. In addition, based on a tricky design of the observer, the time-varying actuator degradation factor term is developed in the error system. On the basis of the state estimation, an integral-type adaptive fuzzy sliding mode controller is constructed to ensure the stability of the closed-loop system. Finally, the effectiveness of the proposed control methods can be illustrated with a numerical example.

Bandung and Lembang are the cities that are chosen by many tourists (local and foreign) as their destinations. Geographically, these cities are placed side-by-side and each city has its own characteristics. As in Bandung, there are many hotels and culinary spots, meanwhile, in Lembang, there are many scenery tourism spots. Tourists usually have limited time to visit all the destinations on holiday, which makes them choose several tourist destinations to visit. In this paper, the tourism itinerary recommendation system is proposed by calculating the most optimal route between destinations and approaching the Vehicle Routing Problem with Time Windows. The optimal route is defined by using Dijkstra the shortest path algorithm by using the collaboration between the road information (road length, traffic condition, travel time, and weather condition) and criteria weight that is determined using the Analytics Hierarchy Process as the graph weights. According to the simulation results, the criteria weights are 6.9%, 62.7%, 18.6%, and 11.9% for Route Length, Traffic Condition, Travel Time, and Weather Condition respectively. Moreover, the optimal number of tourism itinerary plans for the tourist in this research is 4 destinations. As the usage of computational resources, it takes 31.8% of CPU and 61.9% of Memory usage. For the time processing, it increases exponentially as the increment of number of requested stops. The output of this research is expected to be a solution to the tourist itinerary plan, especially in Bandung and Lembang.

This paper presents an approach to the vibration analysis of axially functionally graded non-prismatic Timoshenko beams (AFGNPTB) using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, shear moduli, and mass density) of axially functionally graded beams vary along the longitudinal axis. The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFGNPTB was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFGNPTB, considering the damping. The results obtained in this study showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

Magnetoelectric (ME) sensor is a new type magnetic sensor with ultrahigh sensitivity, low power consumption, and suitable for the measurement of low frequency weak magnetic field. In this study, metglas/PZT-5B ME sensor with a mechanical resonance frequency f_res of 60.041 kHz was prepared. It is interesting to note that its magnetic field resolution reaches 0.20 nT at f_res and 0.34 nT for DC field, respectively. In order to measure the ultralow frequency AC magnetic fields, a frequency upconversion technique was employed. Under this technique, a limit of detection (LOD) of AC magnetic field lower than 1 nT at 8 Hz is obtained, and the minimum LOD of 0.51 nT is achieved at 20 Hz. The high resolution ME sensor with sub-pT level is promising in the field of low frequency weak magnetic field measurement technology.

African swine fever (ASF) is one of the major threats to pig production, and real-time PCR (qPCR) protocols are integral part of ASF laboratory diagnosis. With the pandemic spread of ASF, commercial kits have risen on the market. In Germany, the kits have to go through an approval process and thus, general validation can be assumed. However, they were never compared to each other. In this study, 12 commercial PCR kits were compared to an OIE recommended method. Samples representing different matrices, genome loads, and genotypes were included in a panel that was tested under diagnostic conditions. The comparison included user-friendliness, internal controls, and the time required. All qPCRs were able to detect ASFV genome in different matrices across all genotypes and disease courses. With one exception, there were no significant differences when comparing the overall mean. The overall specificity was 100 % [95 % CI 87.66 - 100], and the sensitivity was between 95 % and 100 % [95 % CI 91.11 - 100]. As can be expected, variability concerned samples with low genome load. Concluding, all tests were fit for purpose. The test system can therefore be chosen based on compatibility and prioritization of the internal control system.

This paper presents an approach to the vibration analysis of axially functionally graded (AFG) non-prismatic Euler-Bernoulli beams using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, and mass density) of AFG beams vary along the longitudinal axis. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFG non-prismatic Euler-Bernoulli beams was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFG non-prismatic Euler-Bernoulli beams, considering the damping. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

An accurate outbreak prediction of COVID-19 can successfully help to get insight into the spread and consequences of infectious diseases. Recently, machine learning (ML) based prediction models have been successfully employed for the prediction of the disease outbreak. The present study aimed to engage an artificial neural network-integrated by grey wolf optimizer for COVID-19 outbreak predictions by employing the Global dataset. Training and testing processes have been performed by time-series data related to January 22 to September 15, 2020 and validation has been performed by time-series data related to September 16 to October 15, 2020. Results have been evaluated by employing mean absolute percentage error (MAPE) and correlation coefficient (r) values. ANN-GWO provided a MAPE of 6.23, 13.15 and 11.4% for training, testing and validating phases, respectively. According to the results, the developed model could successfully cope with the prediction task.

Cooling fans are one of the critical components of air-forced (AF) dry-type transformers for regulating internal temperatures. Therefore, effective malfunction detection is crucial to maintain the transformer temperature within an acceptable range and prevent overheating. Regular maintenance occurs periodically and issues with cooling fans may arise between maintenance periods, leading to prolonged operation under malfunctioning conditions and potential failures. In addition, utilities typically have online information about whether a fan works or not without providing information about cooling fan malfunctioning circumstances. To address these challenges, this study proposes learning-based online monitoring techniques to detect malfunctions in AF transformer cooling fans. Random forests (RFs) and convolutional neural networks (CNNs) are developed to classify the audio signals from cooling fans into normal and malfunctioning classes. Unlike RFs, which require separate feature extraction, CNNs are trained based on spectrogram images derived from audio signals. Thus, various time-frequency techniques are utilized for feature extraction in RFs. Besides, multiple data augmentation techniques are employed to enhance the dataset size and diversity. Algorithmic performance is optimized through hyperparameter tuning and classifier threshold adjustment. Simulations reveal that CNNs outperform RFs, whereas the latter provides superior interpretability of acoustic features compared to the former.

The Mediterranean diet (MED) is highly recommended. Medical nutrition therapy is the cornerstone of diabetes treatment. We assessed adherence to the MED, and resultant micronutrient intake and glycemic control in youth with type 1 diabetes. Twenty adolescents, median age 18 years (interquartile range: 15.5-21), median diabetes duration 9 years (7-14), using continuous glucose monitoring devices, received personalized diet regimes based on MED. At 6 months post-intervention, the caloric intake remained unchanged; however, the carbohydrate proportion was lower (p=0.058) and the intakes of some monounsaturated fats increased (p=0.049). Sodium intake exceeded the recommended daily allowance by 250% (p=0.653), before and after the intervention. For blood glucose, the percent time-in-range 70-180 mg/dL improved from 52% (38-60) to 63% (47-71) (p=0.047). The total insulin dose decreased marginally, from 0.76 u/kg (0.64-0.97) to 0.72u/kg (0.61-0.89) (p=0.067). BMI z-score and waist circumference did not change (p=0.316 and p=0.161, respectively). Diastolic blood pressure percentile decreased from 73% (68-88) to 69% (50-79) (p=0.028), and LDL cholesterol from 114mg/ dl (105-134) to 104mg/dl (96-124) (p=0.059). The Israeli Mediterranean diet screener score increased, from 8 (7-11) to 13 points (12-14) (p=<0.001). The MED-based intervention demonstrated feasibility and improvements in glycemic outcomes and in certain nutritional parameters.

Pulsed electric fields of specific frequencies emitted by a glass plasma antenna tube have been shown to slow the growth of Acute Lymphoblastic Leukemia cells by as much as 43% when exposed to a series of frequencies between 156kHz and 162kHz. This narrow band of frequencies is termed a “Destructive Cancer Resonant Frequency Formant” (DCRFF).

This paper investigates portfolio optimization methodologies and short-term investment strate-gies in the context of the cryptocurrency market, focusing on ten major cryptocurrencies from January 2020 to November 2023. We employ high frequency data and utilize the Kurtosis Mini-mization methodology, alongside other optimization strategies, to construct and evaluate port-folios under different rebalancing frequencies. The empirical analysis reveals that cryptocurren-cies exhibit significant volatility, skewness, and kurtosis, necessitating sophisticated portfolio management techniques. We find that the Kurtosis Minimization methodology consistently outperforms other optimization strategies, delivering optimal returns to investors, particularly in shorter-term investment horizons. We demonstrate the diversification benefits of integrating cryptocurrencies into multi-asset portfolios and emphasize the importance of regular portfolio rebalancing in the volatile cryptocurrency market. Our findings offer insights for portfolio man-agers and investors seeking to optimize their investment outcomes in the cryptocurrency market, highlighting the importance of risk management, diversification, and dynamic portfolio man-agement strategies.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

The active layer thickness (ALT) is affected by local soil material and surface vegetation coverage in Tibetan plateau permafrost region. The human activities and engineering construction along the Qinghai-Tibet Highway (QTH) destroyed the surface vegetation coverage, which have seriously influenced the ALT and heat exchange balance. Meanwhile, the changes of the detailed internal structure in the active layer will affect the stability of engineering infrastructure. Ground-penetrating radar (GPR) was used to detect the ALT in the permafrost region. However, researches on the detailed structure of the active layer and spatial variation information of ALT are rare, the main reason given for this is that the lack of advanced imaging techniques to enhance the GPR images. In this paper, the researchers focus on solving this problem by applying the reverse time migration (RTM) method to GPR field data acquired in the Beiluhe region. Analyses of the results led to conclusions as follows: a) The RTM algorithm is proved to be accurate for imaging the characteristics of the active layer through the dielectric constant model obtained by common midpoint and GPR data velocity analysis. b) The result of RTM profiles show the loose structure and graben-like fine internal structure. Combining with drill data and soil materials information, the researchers deduce the graben-like structure might be coarse gravel layer, which may be related to subgrade settlements in some local area. c) The 2D contour maps not only show the spatial variation feature of ALT at two sides of the highway, but also can compensate the defect of the research for single 2D survey line. The ALT is about 0.6~0.8 m in most areas, and about 0.8~0.9 m near the highway at west side of the QTH on the 2D contour maps. From the RTM interpretation profile, the closer to the plash, the deeper thawed active layer. The detailed internal structure of the active layer and 2D contour maps of ALT have great significance for the study of fine internal structure and the characteristic of ALT spatial variation in the Tibetan plateau under the background of climatic change.

Einstein’s publication of the Special Theory of Relativity in 1905 gave birth to the space-time model as a fundamental arena of the universe. Time has become 4th dimension of space and theoretically one could move backward and forward in time. Hypothetical time travel has been a hot topic of scientific discussion since Kurt Gödel published his article about closed time-like curves (CTC) in 1949. He was aware that his CTC model confirms that there is no physical time. Physicists understood his model as a theoretical frame for time travel. Recent research confirmed that universal space is time-invariant. Motion happens only in space and time is the duration of motion. Nobody can travel in time because time has no physical existence. Time as duration is an emergent physical quantity entering existence in the process of measurement of the duration of material change with clocks. The universal space is utterly timeless. There is no physical time in the universe.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

A new low-pass filter (LPF) circuit with independent adjustment of various, incl. digitally controlled, pole frequency resistors, pole quality factor and transmission coefficient. The proposed low-pass filter is based on the use of the properties of a multi-differential operational amplifier that performs the functions of a signal adder. The peculiarity of the filter is that it has three inputs, with respect to which different transmission coefficients are implemented, incl. inverting (-1) and non-inverting (+1). To check these properties of a low-pass filter in the Micro-Cap environment, computer simulation of a specific circuit was performed on a multi-differential operational amplifier AD 8130. Mathematical expressions are given for the main parameters of the proposed low-pass filter, which allow parametric synthesis of elements of a specific circuit under given restrictions on the used element base.

A new circuit of a low-pass filter (LPF) is considered, which is switched on at the input of analog-to-digital converters to limit the spectrum of input signals. The peculiarity of the proposed low-pass filter is the independent adjustment of the pole frequency, the quality factor of the pole and the transmission coefficient by different resistors. Computer simulation performed in the Micro-Cap environment confirms these properties of the LPF. The basic mathematical expressions are obtained, which make it possible to carry out the parametric synthesis of the LPF circuit. It is shown that the sensitivity of the LPF transmission coefficient to changes in the parameters of the frequency-setting elements of the circuit is close to zero and depends only on the ratio of the resistances of the two resistors in the feedback circuit.

The article considers an internal boundary value problem of the distribution of an electrostatic field in a lens formed by two identical semi-infinite circular cylinders coaxially located inside an infinite external cylinder. The problem is reduced to solving a system of singular Wiener-Hopf integral equations, which is further solved by the Wiener-Hopf method using factorized Bessel functions. Solutions to the problem for each region inside the infinite outer cylinder are presented as exponentially converging series in terms of eigenfunctions and eigenvalues.