Space-based Interferometric Synthetic Aperture Radar (InSAR) applications have been widely used to monitor the cryosphere over past decades. Because of temporal decorrelation, interferometric coherence often severely degrades on fast moving glaciers. In addition, higher sensitivity ambiguity occurs in large baseline configurations, which are needed for extracting topographic information over low relief areas such as the surface of a glacier. TerraSAR-X add-on for Digital Elevation Measurement (TanDEM-X) observations, which overcome the temporal decorrelation because of their simultaneous measurements by two satellite constellations, have used a short baseline sufficient for generation of excellent digital elevation models in most locations around the world. However, it remains difficult to estimate detailed topographic characteristics over low slope glacier surfaces because of the relatively less sensitive height ambiguity from the small baselines. In this study, we used the TanDEM-X pursuit monostatic mode with large baseline formation following a scientific phase timeline to develop highly sensitive topographic elevation models of the Petermann Glacier of Northwest Greenland. As expected, coherent interferometric phases (> 0.8) were well maintained over the glaciers despite their fast movement thanks to the nearly simultaneous TanDEM‐X measurements. The height ambiguity, which defined as the altitude difference correspondent to phase change of flattened interferogram, of the dataset was 10.63 m, which is favorable for extracting topography in a low relief region. We validated the TanDEM‐X derived glacial topography by comparing it to the SAR/Interferometric radar altimeter observations acquired by CryoSat‐2 and the IceBridge Airborne Topographic Mapper laser altimeter measurements. Both observations showed very good correlation within a few meters of the offsets (‐12.5 – ‐3.1 m) with respect to the derived glacial topography. Because of highly sensitive ambiguity, we could successfully extract detailed geomorphological features on the glaciers. Routine TanDEM-X observations will be very useful to better understand the dynamics of glacial movements and topographic change.

The TanDEM-X mission is acquiring a new dataset to provide a temporally independent DEM, called "TanDEM-X Change DEM". This set of acquisitions taken between 2017 and 2020 has a clear temporal separation to the TanDEM-X global DEM data which were acquired between 2010 and 2015. Therefore, this new DEM aims to enable the characterization of terrain changes. Improvements in the acquisition planning and the data processing were necessary to generate this Change DEM with fewer acquisitions but still very high accuracy. For this, the use of an edited TanDEM-X DEM as a "starting point" for the interferometric processing is mandatory.

This research is related to the eco-hydrological problems of herbaceous wetland drying and biodiversity loss in the floodplain lakes of the Middle Basin of the Biebrza river (Poland). An experiment was set up, whose main goals were: (i) mapping the vegetation types and the temporarily or permanently flooded areas, and (ii) comparing the usefulness of C-band Sentinel-1A (S1A) and X-band TerraSAR-X/TanDEM-X (TSX/TDX) for mapping purposes. The S1A imagery was acquired on a regular basis using the dual polarization VV/VH and the Interferometric Wide Swath Mode. The TSX/TDX data were acquired in quad-pol, a fully polarimetric mode, during the Science Phase. The paper addresses the following aspects: i) wetland mapping with S1A multi-temporal series; ii) wetland mapping with fully polarimetric TSX/TDX data; iii) comparing the wetland mapping using dual polarization TSX/TDX subsets, i.e. HH-HV, HH-VV and VV-VH; iv) comparing wetland mapping using S1A and TSX/TDX data based on the same polarization (VV-VH); v) studying the suitability of the Shannon Entropy for wetland mapping; and vi) assessing the contribution of interferometric coherence for wetland classification. The experimental results show main limitations of the S1A dataset, while they highlight the good accuracy that can be achieved using the TSX/TDX data, especially those taken in fully polarimetric mode.

Two-dimensional mass spectrometry (2D MS) is a method for tandem mass spectrometry that relies on manipulating ion motions to correlate precursor and fragment ion signals. 2D mass spectra are obtained by performing a Fourier transform in both the precursor ion mass-to-charge ratio (m/z) dimension and the fragment ion m/z dimension. The phase of the ion signals evolves linearly in the precursor m/z dimension and quadratically in the fragment m/z dimension. This study demonstrates that phase-corrected absorption mode 2D mass spectrometry improves signal-to-noise ratios by a factor of 2 and resolving power by a factor of 2 in each dimension compared to magnitude mode. Furthermore, phase correction leads to an easier differentiation between ion signals and artefacts, and therefore easier data interpretation.

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.

IL1RA intron 2 86-bp repeat and IL4 intron 3 70-bp repeat are VNTRs that have been associated with various diseases, but their role in obesity is elusive. The objective of this study was to investigate the association of IL1RA and IL4 VNTRs with obesity and adiposity in 315 Malaysian subjects (128 M/187 F; 23 Malays/251 ethnic Chinese/41 ethnic Indians). The allelic distributions of IL1RA and IL4 were significantly different among ethnicities, and the alleles were associated with total body fat (TBF) classes. Individuals with IL1RA I/II genotype or allele II had greater risk of having higher adiposity - even after controlling for ethnicity [Odds Ratio (OR) of I/II genotype = 12.21 (CI = 2.54, 58.79; p = 0.002); II allele = 5.78 (CI = 1.73, 19.29; p = 0.004)]. However, IL4 VNTR B2 allele was only significantly associated with overall adiposity status before adjusting for ethnicity [OR = 1.53 (CI = 1.04, 2.23; p = 0.03)]. TBF was also significantly higher in those with IL1RA II allele compared with I allele (31.79 ± 2.52 vs. 23.51 ± 0.40; p = 0.005). Taken together, IL1RA intron 3 VNTR seems to be a genetic marker for overall adiposity status in Malaysian subjects.

The quality of photogrammetric-based derived products like orthophotos, digital terrain models (DTMs) and digital line maps as well as the global digital elevation models (DEM) are rigorously dependent on the accuracy of image orientation. This paper evaluates the vertical accuracy of aerial photogrammetric Digital Terrain Model (DTM), Shuttle Radar Topography Mission (SRTM), Advanced Spaceborne Thermal Emission and Reflectance Radiometer (ASTER), and TerraSAR-X's twin satellite of TanDEM-X (TDX) datasets against in-situ orthometric heights computed from ellipsoidal heights and the 2008 Earth Gravitational Model (EGM2008) derived geoid heights in Ethiopia. The quality of the four global digital elevation models was also validated against the aerial photogrammetric DTM measurements. Besides, the accuracies of the photogrammetric DTM and the four DEM products were checked for their compliance to the American Society for Photogrammetry and Remote Sensing (ASPRS) standards as well as the Ethiopian national vertical data evaluation standards. The study showed that the photogrammetric DTM is in a good agreement with the reference orthometric heights compared to SRTM, ASTER and TDX datasets. More precisely, the result has an absolute accuracy of 1.67 m at Linear Error (LE) 95% confidence level, while the absolute accuracy of SRTM3 arc seconds (SRTM3) at LE 90% (11.91 m) is better than its product specification (16 m). The absolute accuracy of SRTM1 arc second (SRTM1) (7.70 m at LE 90%) surpasses that of SRTM3, whereas the absolute accuracy of ASTER DEM is somehow below its product specification. TDX also has the same vertical accuracy (10.29 m at LE 90%) compared to its product specification (10 m). Furthermore, the vertical accuracy of the photogrammetric DTM meets the100 cm vertical accuracy of the 2015 ASPRS standard. However, it does not meet the Ethiopian national vertical data accuracy requirement standard, i.e., RMSEz of ± 0.45 m. In general, the photogrammetric DTM, SRTM1, and TDX have been proven a superior product over the SRTM3 and ASTER DEMs, and better to use these products for high-level precision and accuracy required applications.

The present work describes the optimization and validation of a highly selective and sensitive analytical method using solid phase extraction and liquid chromatography tandem mass spectrometry (SPE LC-MS/MS) for the determination of some frequently prescribed pharmaceuticals in urban wastewater received and treated by Sharjah sewage treatment plant (STP). The extraction efficiency of different SPE cartridges was tested and the simultaneous extraction of pharmaceuticals was successfully accomplished using hydrophilic-lipophilic-balanced reversed phase Waters^® Oasis HLB cartridge (200 mg/ 6 mL) at pH 3. The analytes were separated on an Aquity BEH C₁₈ column (1.7 µm, 2.1 mm x 150 mm) using gradient elution and the mass spectrometric analysis were performed in multiple reactions monitoring (MRM) selecting two precursor ions to produce ion transition for each pharmaceutical using positive electrospray ionization (+ESI) mode. The correlation coefficient values in the linear calibration plot for each target compound exceeded 0.99 and the recovery percentages of the investigated pharmaceuticals were more than 84%. Limit of detection (LOD) varied between 0.1-1.5 ng/L and limit of quantification (LOQ) was 0.3-5 ng/L for all analytes. The precision of the method was calculated as the relative standard deviation (RSD%) of replicate measurements and was found to be in the ranges of 2.2% to 7.7% and 2.2% to 8.6% for inter and intra-day analysis, respectively. All of the obtained validation parameters satisfied the requirements and guidelines of analytical method validation.

Current satellite remote sensing methods struggle to detect and map forest degradation, a critical issue as it is likely a major and growing source of carbon emissions and biodiveristy loss. TanDEM-X InSAR phase height (hϕ) is a promising variable for measuring forest disturbances, as it is closely related to mean canopy height, and thus should decrease if canopy trees are removed. However, previous research has focused on relatively flat terrain, despite the fact that much of the worlds’ remaining tropical forests are found in hilly areas, and this inevitably introduces artifacts in sideways imaging systems. In this paper, we find a relationship between hϕ and aboveground biomass change in four selectively logged plots in a hilly region of central Gabon. We show that minimising the level of multilooking in the interferometric processing chain strengthens this relationship, and that degradation estimates across steep slopes in the surrounding region are improved by selecting data from the most appropriate pass directions on a pixel-by-pixel basis. This shows that TanDEM-X InSAR can measure the magnitude of degradation, and that topographic effects can be mitigated if data from multiple SAR viewing geometries are available.

Co-doped SnO2 nanocrystals with tetragonal rutile-type (space group P42/mnm) structure have been investigated using in-situ high-pressure synchrotron angle dis-persive X-ray diffraction till 20.9 GPa at ambient temperature. The analysis of ex-perimental results based on Rietveld refinements suggest that rutile-type SnO2 un-dergoes a structural phase transition at 14.2 GPa to an orthorhombic CaCl2-type phase (space group Pnnm) with no coexistence during the phase transition. No further phase transition is observed till 20.9 GPa. The low-pressure and high-pressure phases are related via a group/subgroup relationship. However, as a discontinuous change in the unit-cell volume is detected at the phase transition, thus, the phase transition can be classified as first-order type. On decompression the transition is found to be re-versible. The results are compared with previous high-pressure studies on SnO2.

The presence of antibiotic residues in honey has recently become a growing public health concern due to the overuse of these products in beekeeping and their transfer to the food industry. The aim of this study was to develop and validate a simple, selective and sensitive method for the simultaneous identification and quantification of residues of twenty-two sulfonamides, trimethoprim and dapsone in honey using a rapid and reliable liquid chromatography–tandem mass spectrometry (LC–MS/MS) method. The developed method showed good linearity, specificity, precision (repeatability and intra-laboratory reproducibility) and recovery. The decision limit (CCalpha) ranged between 2.16-22.12 µg/kg for CCα, while the detection capability (CCbeta) was between 2.16- 2.67-27.36 µg/kg. The method proved to be rapid, reliable and effective for the determination of sulfonamides, trimethoprim and dapsone from honey samples. The average recoveries were estimated to be between 70 and 106%. The relative standard deviations (RSDs) were between 6-18%. In practice, the method is essential to check the honey sold on the market and ensure its safety before it reaches the consumer.

We addressed the frequent occurrence of mixed-chain lipids in biological membranes and their impact on membrane structure by studying several chain-asymmetric phosphatidylcholines and the highly asymmetric milk sphingomyelin. Specifically, we report trans-membrane structures of the corresponding fluid lamellar phases using small-angle X-ray and neutron scattering, which were jointly analyzed in terms of a membrane composition-specific model, including a headgroup hydration shell. Focusing on terminal methyl groups at the bilayer center we found a linear relation between hydrocarbon chain length mismatch and the methyl-overlap for phosphatidylcholines, and a non-negligible impact of the glycerol backbone-tilting, letting the sn1-chain penetrate deeper into the opposing leaflet by half a CH2 group. That is, penetration-depth differences due to the ester-linked hydrocarbons at the glycerol backbone, reported previously for gel phase structures also extend to the physiological more relevant fluid phase, but are significantly reduced. Moreover, milk sphingomyelin was found to follow the same linear relationship suggesting a similar tilt of the sphingosine backbone. Complementary performed molecular dynamics simulations revealed that there is always a part of the lipid tails bending back, even if there is a high interdigitation with the opposing chains. This suggests that hydrocarbon chain interdigitation plays only a minor role in transbilayer coupling. For both cases of adaption to chain length mismatch, chain-asymmetry has a large impact on hydrocarbon chain ordering, inducing disorder in the longer of the two hydrocarbons.

The efficient extraction of phthalate acid esters (PAEs) is challenging due to their extremely low concentration, complicated matrices and hydrophilicity. Herein, hol-low microspheres, as an ideal coating, possesses significant potential for solid-phase microextraction (SPME) due to their fascinating properties. In this study, multi-walled carbon nanotubes hollow microspheres (MWCNTs-HMs) were utilized as a fiber coating for the SPME of PAEs from tea beverages. MWCNTs-HMs were ob-tained by dissolving the polystyrene (PS) cores with organic solvents. Interestingly, MWCNTs-HMs well maintain the morphology of the precursors MWCNTs@PS. The layer-by-layer (LBL) assembly of MWCNTs on PS microsphere templates was ac-quired through electrostatic interactions. Six PAEs, di-ethyl phthalate (DEP), di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-2-ethylhexyl phthalate (DEHP) and di-n-octyl phthalate (DOP), were se-lected as target analytes for assessing the efficiency of the coating for SPME. The stirring rate, sample solution pH and extraction time were optimized by using the Box-Behnken design. Under optimal working conditions, the proposed MWCNTs-HMs/SPME was coupled with gas chromatography-tandem mass spec-trometry (GC-MS/MS) to achieve high enrichment factors (118–2137), wide linearity (0.0004-10 μg L-1), low limits of detection (0.00011-0.0026 μg L-1) and acceptable recovery (80.2%-108.5%) for the detection of PAEs. Therefore, the MWCNTs-HMs coated fibers are promising alternatives in the SPME method for the sensitive detec-tion of PAEs at trace levels in tea beverages.

The increasing use of energy resources recovered from the subsurface environments and the resulting carbon imbalance in the environment has motivated the need to develop thermodynamically downhill pathways to convert and store CO₂ as water insoluble calcium or magnesium carbonates. While previous studies extensively explored aqueous routes to produce calcium and magnesium carbonates from CO₂, there has been a limited scientific understanding of the phase evolution and textural changes during the direct gas-solid conversion routes to produce calcium carbonate from calcium hydroxide, which is one of the abundant constituents of alkaline industrial residues. With increasing interest in developing integrated pathways for capturing, converting and storing CO₂ from dilute flue gases, understanding the compositions of the product phases as they evolve is essential for evaluating the efficacy of a given processing route. Therefore, in this study, we investigate the phase evolution and the corresponding textural changes as calcium hydroxide is converted to calcium carbonate under the continuous flow of CO₂ at an ambient pressure of 1 atm and on heating continuously from 30 °C to 500 °C using in-operando wide angle X-ray scattering (WAXS), small angle X-ray scattering (SAXS), and ultra-small angle X-ray scattering (USAXS) measurements.

The aging mechanism of 10% and 30% nickel substituted manganese hexacyanoferrate cathode material in aqueous zinc-ion batteries has been explored through the advanced synchrotron-based two-dimensional x-ray fluorescence technique. Thanks to the two-dimension modality, not only the metal concentration dynamics throughout the entire electrodes was followed during the aging process, but their spatial distribution was also revealed, suggesting the route of the material transformation. The dissolution of Mn and Ni, and the penetration of Zn inside the framework, alongside the Mn aggregations outside the hexacyanoferrate framework were detected. Additionally, the possibility of conducting x-ray absorption spectroscopy measurements on the regions of interest made it possible to explore the chemical state of each metal, and furthermore, synchrotron-based powder x-ray diffraction demonstrated the gradual structural modification in 30% Ni-containing sample series, in terms of the different phase formation.

Hepatitis B virus (HBV) is the dominant risk factor for hepatocellular carcinoma (HCC). HBV X protein (HBx) plays crucial roles in HCC carcinogenesis. HBx interferes with several signaling pathways including Notch1 pathway in HCC. In our study, we found that Notch1 was highly expressed in HCC especially in large HCC. Notch1 and HBx co-localized in HCC and their levels were positively correlated with each other. Notch1 expression was more elevated in HepG2.2.15 than that in HepG2. HBx activated Notch1 pathway in HepG2.2.15. Repression of HBx and Notch1 pathway attenuated the growth of HepG2.2.15. Notch1, ERK and AKT pathways were inhibited after a γ-secretase inhibitor treatment. Dual-specificity phosphatase 1 (DUSP1) and phosphatase and tensin homolog (PTEN) were up-regulated after the γ-secretase inhibitor treatment and Hes1 inhibition. Luciferase reporter assays showed that Hes1 repressed the promoters of DUSP1 and PTEN and this was reverted by γ-secretase inhibitor treatment. Western blotting demonstrated that DUSP1 dephosphorylated pERK and PTEN dephosphorylated pAKT. Collectively, we reported a link among HBx, Notch1 pathway, DUSP1/PTEN, and ERK/AKT pathways, which influenced HCC cell survival and could be a therapeutic target for HCC.

The formation of solid solution series Cs_1-xM_xGaQ₂-mC64 (M = K, Rb; Q = S, Se; x = 0–1) was studied by X-ray diffraction and spectroscopic methods, revealing a complete miscibility of CsGaQ₂-mC64 with RbGaQ₂ and KGaSe₂, and a large miscibility gap with KGaS₂. All solid solution members exhibit similar Raman spectra, indicating the covalent Ga-Q bonding character. The similar optical band gaps likewise further contribute to this conclusion. Up to a degree of substitution, these solid solutions undergo a phase transition similar to CsGaQ₂-mC64. The influence of the substitution parameter x on phase transition process was investigated in situ using high-temperature X-ray powder diffraction experiments. Phase-pure solid solutions of the high-temperature polymorphs Cs_1-xM_xGaQ₂-mC16 were obtained up to x_max(K) = 0.1 and x_max(Rb) = 0.3. The crystal structures of these new CsGaQ₂-mC16 analogous high-temperature phases were refined from synchrotron diffraction data by Rietveld-refinement.

The outdoor field test of the 4-terminal on Si tandem photovoltaic module (specifically, InGaP/GaAs on Si) was investigated and performance model, considering spectrum change affected by fluctuation of atmospheric parameters, was developed and validated. The 4-terminal on Si tandem photovoltaic module had about 40 % advantage in seasonal performance loss compared with standard InGaP/GaAs/InGaAs 2-terminal tandem photovoltaic module. This advantage is expanded in (subarctic zone) < (temperate zone) < (subtropical zone). The developed and validated model used all-climate spectrum model and considered fluctuation of atmospheric parameters, and can be applied every type of on-Si tandem solar cells.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

In the perspective of designing complex concentrated alloys (CCAs) for structural applications, sigma (σ) phase is important. It is generally known to be an embrittling phase leading to a degradation in the mechanical properties of CCAs. This necessitates detailed investigations on the evolution of σ phase in these alloys. In the present study, an equiatomic CoCrCuMnNi CCA is chosen, in which σ phase appears at 800°C, as reported in a recent publication [1]. To this end, the present investigation aims at understanding the evolution of this phase so that its presence can be controlled for the purpose of preventing degradation in mechanical properties. In the present work, a vacuum arc melted alloy, after homogenisation (at 400°C for 5h), is heat-treated for different times ranging from 1 to 9h at 800°C followed by water quenching. Extensive characterisation has been carried out using X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) techniques to understand the sequence of σ phase precipitation at 800°C.

Orthohepadnavirus causes chronic hepatitis in a broad range of mammals, including primates, cats, woodchucks, and bats. Hepatitis B virus (HBV) X protein inhibits type-I interferon (IFN) signaling, promoting HBV escape from the innate immune system to establish persistent infection. However, whether X proteins of Orthohepadnavirus viruses in the other species have similar inhibitory activity remains unknown. Here, we investigated the anti-IFN activity of 17 Orthohepadnavirus X proteins derived from various hosts. We observed conserved activity of Orthohepadnavirus X proteins in inhibiting TIR-domain-containing adaptor protein inducing IFN-β (TRIF)-mediated IFN-β signaling pathway through TRIF degradation. X proteins from domestic cat hepadnavirus (DCH), a novel member of Orthohepadnavirus, inhibited mitochondrial antiviral signaling protein (MAVS)-mediated IFNβ signaling pathway comparable with HBV X. These results indicate that inhibition of IFN signaling is conserved in Orthohepadnavirus X proteins.

Bat feces were reported in ancient Chinese medicine books to have the effect of reducing heat and improving eyesight, but the mechanism of vision improvement still needs further research. To this end, we used 2,2-diphenyl-1-picrylhydrazyl (DPPH) and liquid chromatography/tandem mass spectrometry (LC/MS/MS) to analyze the antioxidant capacity of and the types of vitamins in bat feces. We hoped to screen the pharmacological components of bat feces, and to explain the role that these components may play in the treatment of visual deterioration. Our results found that bat feces had a good antioxidant capacity and mainly contain vitamins B1 (thiamine), B2 (riboflavin), B3 (nicotinamide), B3 (nicotinic acid), and B5 (pantothenic acid). Although these vitamins may help maintain the health of the optic nerve and cornea, the vitamin content of bat feces is low, but the heavy metal content is high, as shown using inductively coupled plasma mass spectrometry (ICP-MS) analysis. Therefore, we suggest that the use of bat feces as traditional Chinese medicine to improve vision should be strictly restricted.

We assume that the current mathematical knowledge K is a finite set of statements from both formal and constructive mathematics, which is time-dependent and publicly available. Any theorem of any mathematician from past or present belongs to K. The set K exists only theoretically. Ignoring K and its subsets, sets exist formally in ZFC theory although their properties can be time-dependent (when they depend on K) or informal. In every branch of mathematics, the set of all knowable truths is the set of all theorems. This set exists independently of K. Algorithms always terminate. We explain the distinction between algorithms whose existence is provable in ZFC and constructively defined algorithms which are currently known. By using this distinction, we obtain non-trivial statements on decidable sets X⊆N that belong to constructive and informal mathematics and refer to the current mathematical knowledge on X. This and the next sentence justify the article title. For any empirical science, we can identify the current knowledge with that science because truths from the empirical sciences are not necessary truths but working models of truth from a particular context. The feature of mathematics from the article title is not quite new. Church's thesis, which is known from the beginning of computability theory, is based on the observation that the currently known computable functions are recursive, where the notion of a computable function is informal. It proves that the predicate of the current mathematical knowledge slightly increases the intuitive mathematics. For a set X⊆N whose infiniteness is false or unproven, we define which elements of X are classified as known. No known set X⊆N satisfies Conditions (1)-(4) and is widely known in number theory or naturally defined, where this term has only informal meaning. (1) A known algorithm with no input returns an integer n satisfying card(X)<ω ⇒ X⊆(-∞,n]. (2) A known algorithm for every k∈N decides whether or not k∈X. (3) No known algorithm with no input returns the logical value of the statement card(X)=ω. (4) There are many elements of X and it is conjectured, though so far unproven, that X is infinite. (5) X is naturally defined. The infiniteness of X is false or unproven. X has the simplest definition among known sets Y⊆N with the same set of known elements. We prove that the set X={n∈N: the interval [-1,n] contains more than 29.5+(11!/(3n+1))∙sin(n) primes of the form k!+1} satisfies Conditions (1)-(5) except the requirement that X is naturally defined. 501893∈X. Condition (1) holds with n=501893. card(X∩[0,501893])=159827. X∩[501894,∞)={n∈N: the interval [-1,n] contains at least 30 primes of the form k!+1}. If we add to X some set W satisfying 14≤card(W)≤23, then the following statements hold: X does not satisfy Condition (1), 159827+14≤card(X), the above lower bound is currently the best known, card(X)<ω ⇒ card(X)≤159827+23, the above upper bound is currently the best known, X satisfies Conditions (2)-(5) except the requirement that X is naturally defined. Analogical statements hold, if we add to X the set ⋃_{x∈N, x divides 99!} {k∈N: k-501894 is the x-th element of P(n^2+1)}, where P(n^2+1) denote the set of primes of the form n^2+1. For a non-negative integer n, let θ(n) denote the largest integer divisor of 10^{10^{10}} smaller than n. Let κ:N→N be defined by setting κ(n) to be the exponent of 2 in the prime factorization of n+1. The set X={n∈N: (θ(n)+κ(n))^2+1 is prime} satisfies Conditions (1)-(5) except the requirement that X is naturally defined. Condition (1) holds with n=0^{10^{10}}. We present a table that shows satisfiable conjunctions of the form #(Condition1)∧ (Condition 2)∧#(Condition 3)∧(Condition 4)∧#(Condition 5), where # denotes the negation ¬ or the absence of any symbol. No set X⊆N will satisfy Conditions (1)-(4) forever, if for every algorithm with no input, at some future day, a computer will be able to execute this algorithm in 1 second or less. The physical limits of computation disprove this assumption.

With the decline in fossil fuels, hydrogen-based alternatives provide a reliable and clean source for sustainable energy generation. In these endeavors, photochemical splitting for hydrogen production through tandem cells has been the source of much theoretical and experimental research in science. Much focus has been placed on interfacial band gap engineering as one of the most promising routes in the generation of hydrogen.This present work explores sputtering of n-silicon to form the active electrode in a n-Si | n-TiO₂ tandem cell and investigates the effect of variations in sputtering and post sputtering treatment parameters (rapid thermal annealing and long cycle annealing) for successful deposition of crystalline Silicon. The samples were successfully characterized via Raman Spectroscopy, X-ray Diffraction and Optical Transmission Spectroscopy to ascertain prevalent crystalline order and optical band gap, under different sputtering and post-sputtering conditions. Relevant conclusions were drawn to ascertain the best possible deposition parameters of n-Si for photocatalytic water splitting.

Objectives. Optimal treatment strategy for ischemic stroke in patients presenting with tandem occlusions the internal carotid artery remains controversial. Several studies have demonstrated better clinical outcomes after eptifibatide, which is a short half-life antiplatelet agent. This retrospective analysis was focused at safety and efficacy of administration of low-dose eptifibatide in stroke patients with tandem lesions. Methods. We evaluated results of endovascular treatment in 148 stroke patients with tandem lesions. Patients in whom balloon angioplasty alone resulted in satisfactory cerebral flow did not receive eptifibatide (33 patients); others received this drug together with stent implantation (115 patients). Eptifibatide was given in as intravenous bolus 180 g/kg, and then in modified low dose of 1 g/kg/min for 24 hours. Results. There were no statistically significant differences between both groups regarding 30-day mortality, frequency of thrombotic events and hemorrhagic complications. Analysis of clinical status at 30-day follow-up revealed that administration of eptifibatide was associated with statistically significant better outcome: a higher rate of either no neurological symptoms or only mild symptoms (4 NIHSS points maximally). Conclusions. Administration of eptifibatide in stroke patients presenting with tandem lesions is relatively safe. Moreover, treatment with this drug can improve clinical outcomes in these challenging patients.

The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

Fragile X syndrome (FXS) is the most frequent monogenic form of autism spectrum disorder (ASD). Autistic FXS is caused by loss of the fmr1 gene product, the fragile X mental retardation protein (FMRP), triggering physiological and behavioral abnormalities. It is correlated with clock components for behavioral circadian rhythm. Mutation of this gene causes the disturbances in sleep patterns and circadian behavior commonly observed in patients with autistic FXS, accompanied by frequent dysregulation of melatonin synthesis and melatonin-dependent signaling. These changes impair vigilance, learning and memory, and are also linked to autistic behavior including the abnormal anxiety response. However, although several possible causes, symptoms, and clinical features of ASD have been investigated, the correlation between an altered circadian rhythm and autistic FXS has not been extensively studied. Recent works have highlighted the impact of melatonin on the nervous, immune, and metabolic systems. Even though utilization of melatonin for sleep disorder in ASD has been considered in clinical research, further studies should be aimed at its neuroprotective role in ASD during developmental period. In this review, we focus on the regulatory circuits involved in melatonin dysregulation and circadian system disruption in those with autistic FXS. Additionally, we discuss the neuroprotective effect of melatonin intervention. This may improve neuroplasticity and physical capability. We also review the underlying molecular mechanisms, and suggest that melatonin may be a useful novel treatment for autistic FXS, countering the adverse effects of circadian variation.

Brimonidine, a selective alpha-2 adrenergic agonist, used for treatment of open-angle glaucoma, has been shown to cause neurological side effects such as unresponsiveness, lethargy, hypoventilation, and stupor, mimicking opioid toxicity. We report one case of transient encephalopathy in a toddler, in whom brimonidine accidental toxicity was sus-pected and then confirmed by a toxicology study. The 8-month-old healthy girl child was taken to the pediatric ER since she was drowsy and hypotonic, with miosis. Brain CT scan and toxicological work-up on blood and urine were negative. Starting from hour +4, the child progressively improved, and by hour +6, she recovered to a normal state of consciousness. A survey of available drugs at the child’s reach showed the presence of brimonidine. Thus, ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS) was applied to quantify brimonidine in urine and plasma samples, showing 8.40 ng/mL level and 0.79 ng/mL, respectively. To our knowledge, this is the first report for determining brimonidine levels in urine and plasma by UPLC-MS/MS. Insufficient knowledge of the family members about the potential hazards of an apparently innocuous, topical medication such as eye drops may put children at a greater risk of poisoning. Necessary warnings should be better given to parents when prescribing this medication.

In recent years, the manufacturing sector has benefited from a variety of technological innovations regarding automation and utilization of artificial intelligence on the shopfloor. During the manufacturing processes of a product, a variety of meta data can be derived from each working step and considered during subsequent stages of its liefycle like shipment, utilization or recycling. With upcoming regulations decided by the European Union, manufacturers must begin to react to the demand of a comprehensive circular economies by introducing technical solutions like Digital Product Passports (DPP). By associating the specific conditions of all stages in the life of a product within a digital identity, e.g., the DPP, transparency and efficiency can be increased. The Gaia-X service landscape aims at realizing federated data infrastructures, enabling robust and transparent services while considering data sovereignty. In this work, a modular and generic multi-tenant framework for utilizing DPPs within cross-company ecosystems is presented with respect to the manufacturing sector. In applying the Secret Network-blockchain for implementing the automation of DPP management processes, premises for Gaia-X compliance and therefore strengthened trust-anchors are realized. By considering details of ecosystems, as well as most interesting security threats to the proposed architecture, a holistic view of applying DPPs in the context of smart production supply chains is shown. In presenting a simple but vivid use case of the production and compilation of car wheels, the fundamental benefits of the work on hand are underlined, once more.

A metal-free electrochemical oxidative difluoroethylation of 2-arylbenzimidazoles was accomplished, which provided an efficient strategy for the synthesis of MeCF2-containing benzo[4,5]imidazo[2,1-a]-isoquinolin-6(5H)-ones. In addition, the method also enabled the efficient construction of various difluoroethylated indolo[2,1-a]isoquinolin-6(5H) ones. Notably, this electrochemical synthesis protocol proceeded well under mild conditions without metal catalysts or exogenous additives/oxidants added.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

The organic solar cells (OSCs) have drawn attention in the past decade due to its cynosure in industrial manufacturing because of its promising properties such as low weight, highly flexible and low cost production. However, low η restricts the utilization of OSCs for potential application such as low cost energy harvesting devices. In this paper, OSCs structure based on triple junction tandem scheme is reported with three different absorber materials with the objective to enhance the absorption of photons which in turn improves the η, as well as its correlating performance parameters. The investigated structure gives the higher value of η = 14.33% with Jsc=16.87 (mA/m2), Voc=1.0 (V), and FF=84.97% by utilizing a stack of three different absorber layers with different band energies. The proposed structure is tested under 1.5 (AM) with 1 sun (W/m2). The impact of top, middle and bottom sub cells thickness on η is analyzed with a terse to find the optimum thickness for three sub cells to extract high η. The optimized structure is then tested with different electrode combination and the highest η is recorded with FTO/Ag. Moreover, the influence of upsurge temperature is also demonstrated on the proposed structure and observed that the upsurge temperature has greatly affected the electrical parameters of the device and η decreases from 14.33% to 11.40% when the temperature of the device rises from 300-400 K.

Centromeres are among the fastest evolving genomic regions in a diverse array of organisms. The evolutionary process driving this rapid evolution has not been unambiguously established. Here I integrate diverse information to motivate a model in which centromeres evolve rapidly because of their intrinsic molecular phenotype: they tightly bind centromeric proteins throughout the cell cycle. DNA-bound proteins have been shown to cause stalling and collapse of DNA replication forks in many genomic regions, including centromeres. Collapsed replication forks generate one-sided double strand breaks (DSBs) that are repaired by the Break-Induced Repair (BIR) pathway. Here I show why this repair is expected to generate tandem repeat structure and three key features at centromeres: i) increased nucleotide substitution mutation rates, ii) out-of- register re-initiation of replication that leads to indels spanning one or more repeat units, and iii) elevated rates of large and small transpositions within centromeres and between genomic regions. These phenotypes lead to: i) a rapid rate of nucleotide substitutions within a clade of centromeric sequences, ii) continual turnover of monomers within centromeres that fosters molecular-drift and molecular-drive, and iii) recurrent quantum leaps in centromere sequence due to the formation of mosaic monomers and new sequences transposed into non-homologous centromeres. These features are plausibly the major reason centromeres evolve so rapidly. I also speculate on how the DNA sequence of centromeres might perpetually coevolve with the protein sequence of histone CENH3 –the major epigenetic mark of centromeres.

The rapid and accurate detection of parasites is crucial for timely curative intervention in parasitosis and for epidemiological surveillance. To meet the needs of clinical diagnosis, it is imperative to develop a diagnostic tool based on nucleic acid that combines the sensitivity and specificity of established nucleic acid amplifica-tion tests with the speed, cost-effectiveness, and convenience of isothermal amplification methods. A new nu-cleic acid detection method, utilizing the clustered regularly interspaced short palindromic repeats (CRISPR)-associated (Cas) nuclease, holds promise for point-of-care testing. Specifically, the CRISPR-Cas12a system has demonstrated numerous advantages for detecting parasites, with hopeful outcomes for identify-ing malaria, toxoplasmosis, and other parasitic ailments. This review provides an overview of how CRISPR-Cas12a can be utilized for parasite detection, evaluates its advantages and disadvantages, and sug-gests ways to improve the efficiency and sensitivity of CRISPR-Cas12a-based assays.

In recent years Pd-containing catalytic systems for tandem processes has drawn special attention due to the enhanced catalytic properties and possibility to perform several reactions without the necessity to separate the intermediates. In this review, recent progress in Pd-catalyzed tandem processes is considered. Three types of catalytic systems were described: homogeneous catalysts (including immobilized Pd complexes); heterogeneous catalysts supported on oxides, MOFs, COFs, etc. with particular attention to the supports containing acid/base sites; metal-enzyme catalysts for chemoenzymatic tandem processes applied in fine organic synthesis and biotechnology. For homogeneous Pd-catalyzed reactions different tandem reactions were considered, i.e. cross-coupling, cyclization, carbonylation, isomerization, alkylation, arylation, etc.

We enhance Frobenius' method for solving linear ordinary differential equations about regular singular points. Key to Frobenius' approach is the exploration of the derivative with respect to a single parameter; this parameter is introduced through the powers of generalized power series. Extending this approach, we discover that tandem recurrence relations can be derived. These relations render coefficients for series occurring in logarithmic solutions. The method applies to the, practically important, exceptional cases in which the roots of the indicial equation are equal, or differ by a non-zero integer. We demonstrate the method on Bessel's equation and derive previously unknown tandem recurrence relations for coefficients of solutions of the second kind, for Bessel equations of all integer and half-integer order.

In this case study, an active runway of a civilian airport in Zonguldak, Turkey, is used to assess the suitability of spaceborne digital elevation models (DEMs) to model an anthropogenic structure. The tested DEMs include the ASTER, the AW3D30 m, the SRTM-1”, the SRTM-3”, the SRTM-X, the TanDEM-3”, and the WorldDEMTM. A photogrammetric high accuracy DEM was also available for the tests. As a reference dataset, a line leveling survey of the runway using a Leica Sprinter 150/150M instrument was performed. The selection of a runway as a testbed for this type of investigation is justified by its unique characteristics, including its flat surface, homogenous surface material, and availability for a ground survey. These characteristics are significant because DEMs over similar structures are free from environment- and target-induced error sources. The most accurate DEM is the WorldDEMTM followed by the SRTM-3” and TanDEM-3”, with vertical errors (LE90) equal to 1.291 m, 1.542 m, and 1.56 m, respectively. This investigation uses a method for identifying the vertical errors in DEMs that is known as the runway method.

Lectins, characterized by their carbohydrate-binding ability, have an extensive practical application. However, their industrial use is limited by low yields, and few active recombinant lectins have been reported. In this study, the algal lectin BPL-3 (Bryopsis plumosa lectin 3) was successfully produced using a bacterial expression system, BL21(DE3), with an artificial repeated structure (dimeric construct). Recombinant dimeric BPL3 (rD2BPL3) was confirmed by LC-MS/MS spectrometry. Expression efficiency was greater for the construct with the repeat structure (rD2BPL3) than the monomeric form (rD1BPL3). Optimal conditions for expression were 1 mM IPTG at 20 °C. Recombinant lectin was purified under denaturing conditions and refolded by the flash dilution method. Recombinant BPL3 was solubilized in 1× PBS containing 2 M urea. rD2BPL3 showed strong hemagglutination activity using human erythrocytes, similar to that of native BPL3. rD2BPL3 had a similar sugar specificity to that of the native protein, i.e., to N-acetyl-glucosamine (GlcNAc) and N-acetyl-galactosamine (GalNAc). Glycan array results showed that recombinant BPL3 and native BPL3 exhibited different binding properties. Both showed weak binding activity to α-Man-Sp. Native BPL3 showed strong binding specificity to the alpha conformation of amino sugars, and rD2BPL3 had binding activity to the beta conformation. The process developed in this study was suitable for the quality-controlled production of high amounts of soluble recombinant lectins.

Examining forbidden reflections provides valuable information on electronic states and the local environment of resonant atoms in crystals. Experimental studies of two forbidden reflections 002 and 100 in TeO₂ single crystals were performed at photon energies close to the L₁ tellurium absorption edge. It was found that the spectral form corresponding to these two reflections looks almost identical, which is completely unexpected for a highly anisotropic material. Theoretical consideration shows that only one component f_xy of the tensor describing dipole-dipole resonance scattering contributes to the 002 reflection, while two components f_xy and f_xz correspond to the 100 reflection. Numerical calculations show that the latter tensor component is comparable to the first one, but the combination of several geometric factors leads to the fact that its contribution to the spectrum is negligible. This explains the experimentally observed results. The finding shows a way for targeted investigation of single tensor components and makes it possible to compare different spectra and use them the study the physical phenomena in functional materials.

A lot of research studies have been surveyed the completed genomes of prokaryotic and eukaryotic and focused on the correlation between the percentage of microsatellite sequences in completed genomes and the whole size of the organism genomes. There are fewer studies made in repetitive sequences otherwise simple sequence repeats or long tandem repeats of virus genomes. simple sequence repeats (SSRs) are the most important regions for recombination and moving repeats blocks from site to another site in the genomes. A tool was programmed and designed by visual basic 6.0 to find the long tandem repeats in DNA sequences of the small genomes. The tool named “Repeater Finder Regular Expression”, (RFRE) Version 1.0, 2016. The tool was utilized to discover different pattern of long tandem repeats (LTR) motifs on the completed genomes of human corona virus strains by using a joined regular expression language. In this study, a twenty-nine accession numbers of human coronavirus completed genomes, (hku1) strains were retrieved from the Genbank. The researcher can write a different regular expression patterns and joined regular expression patterns through the designed tool to search and find a specific motif of nucleotide sequences inside the complete genomes. The RFRE tool searched and found three different total lengths of a perfect long tandem repeats (240bp, 300bp and 480bp). A Dot plot gave a picture view for the long tandem repeat sequences in the completed genome sequence (KF430201.1) of human coronavirus. The genomic dot plot tool YASS was used as a genomic similarity searching tool to check for the uninterrupted repeats and confirm the sensitivity of the (RFRE) tool. To identify the recombination site in the genomes of human coronavirus the RAT tool was applied to find the recombination sites between the completed genomes of human corona viruses .The RAT tool recognized the recombination site in the nucleotide position (3012) and at the same time this recombination site position (3012) was also recognized as a beginning position of a long tandem repeat. A precise motif was predicted from the translated repeats of Human Corona Virus which found by PRATT tool. There was a relationship between the total length of long tandem repeats and genome size of Human Corona Virus and the correlation value R² was equal to (0,451). In conclusion, this study presented the importance of finding the long tandem repeats of human coronavirus and gives a relationship between the completed genome size of human coronavirus types and long tandem repeats. The nucleotide position (3012) was a hot spot site for a recombination among the complete genomes of human coronavirus and also identified as a repetitive site in the genomes of human corona virus (hku1). The repeats in human coronavirus (hku1) were predicated to be a main major role of virus evolution.

The analysis of autosomal polymorphism (STR) or Y chromosome polymorphisms (Y-STR) are usually used for the study and deconvolution of mixed DNA profiles in forensic genetics, accompanying data interpretation with biostatistical evaluations (e.g. RMP, RMNE, LR). Sometimes, however, some mixed DNA profiles are so complex that the autosomal and Y markers do not allow a correct discrimination and identification. In this work is reported a robbery case in which the analysis of the polymorphic markers of the X chromosome was applied to the mixed profiles obtained from the traces, thus falling outside the classic relationship use of the X-STRs. The aim of the authors is, in fact, to encourage the classic use of X-STRs not only in parental relationships, but also in purely forensic cases for interpreting complex mixed DNA profiles. Their application in case resolution could be more decisive than STR/Y-STR.

A enantioselective tandem transformation concerning asymmetric allylic decarboxylative addition and cyclization of N-nosylimines with vinylethylene carbonates (VECs) in the presence of [Rh(C2H4)2Cl]2, chiral sulfoxide-N-olefin tridentate ligand has been developed. The reaction of VECs with various substituted N-nosylimines proceeded smoothly under mild conditions, giving highly functionalized oxazolidine frameworks in good to high yields with good to excellent enantioselectivity.

A sustainable, scalable source of energy‐dense chemical fuel is urgently needed to ensure the security of our energy supply for future generations. Solar energy is the only renewable energy source of sufficient scale to replace fossil fuels and meet rising environmental demand. Hydrogen is expected to play a key role as an energy carrier in future energy systems of the world. As fossil fuel supplies become scarcer and environmental concerns increase, hydrogen is likely to become an increasingly important chemical energy carrier and eventually may become the principal chemical energy carrier. When most of the world’s energy sources become non-fossil based, hydrogen and electricity are expected to be the two dominant energy carriers for the provision of end-use services. Photocatalytic hydrogen evolution from water by solar energy over semiconductors offers a promising way for clean and renewable production of hydrogen. The TiO2-based materials have received considerable attention in recent years due to their extensive application in photocatalysis for hydrogen evolution. Though TiO2 is the most widely investigated photocatalyst for hydrogen evolution, it still provides low photocatalytic activity due to the wide bandgap that results in photocatalytic activity only under ultraviolet (UV) irradiation. Modification of TiO2 photocatalysts with several transition metals has been extensively studied to extend the absorbance capacity of TiO2 into the visible range. The effect of different photocatalytic deposition and reaction parameters also play major roles in enhancing the photostability of photoanode and increasing the hydrogen gas output, respectively.

Stable-isotope dimethyl labeling is a highly reactive and cost-effective derivatization procedure that could be utilized in proteomics analysis. In this study, a liquid chromatography-tandem mass spectrometry in multiple reaction monitoring mode (LC-MS-MRM) platform for the quantification of kiwi allergens was first developed using this strategy. Three signature peptides for target allergens Act d 1, Act d 5, and Act d 11 were determined and were derivatized with normal and deuterated formaldehyde as external calibrants and internal standards, respectively. The results showed that sample preparation with the phenol method provided comprehensive protein populations. Recoveries at four different levels ranging from 72.5–109.3% were achieved for the H-labeled signature peptides of Act d 1 (SPA1-H) and Act d 5 (SPA5-H) with precision ranging from 1.86–9.92%. The limit of quantification (LOQ) was set at 8 pg mL–1 for SPA1-H and at 4 ng mL–1 for SPA5-H. The developed procedure was utilized to analyze seven kinds of hand-made kiwi foods containing 0.0175–0.0515 mg g–1 of Act d 1 and 0.0252–0.0556 mg g–1 of Act d 5. This study extended the applicability of stable-isotope dimethyl labeling to the economical and precise determination of food allergens and peptides.

It is well known that X-ray crystallography is based on X-ray diffraction (XRD) by atoms and molecules. The diffraction pattern arises as a result of scattering of incident radiation, which makes it possible to determine the structure of the scattering substance. With the advent of ultrashort radiation sources, the theory and interpretation of X-ray diffraction analysis remained the same. This work shows that when an attosecond laser pulse is scattered on a DNA molecule, including during its nicking and bending, the pulse duration is an important characteristic of the scattering. In this case, the diffraction pattern changes significantly compared to the previously known scattering theory. The results obtained must be used in XRD theory to study DNA structures, their mutations and damage, since the previously known theory can produce large errors and, therefore, the DNA structure can be “deciphered” incorrectly.

Heat stress affects the yield of medicinal plants and can reduce biomass and/or metabolite production. In order to evaluate the effect of heat-induced stress on the essential oil production in Mentha x piperita L. var. Mitcham (Mitcham mint) and Mentha x arvensis var. piperascens Malinv. ex L. H. Bailey (Japanese mint), we studied the chemical composition of the oils of the two mint species under different heat shock stress in growth chambers. The antibacterial activity of the essential oils was also evaluated; microscopic observation (fluorescence and electron transmission) was used to assess the effect of the tested samples on bacterial growth. The results obtained shed light on the mint essential oils composition and biological activity in relation to heat stress.

High salinity in soil affects the normal growth and development of crop. MicroRNA171 (miR171) plays a momentous role in plant resistance to adversity stress. The functions of Sly-miR171d and Sly-miR171e on growth of tomato and fruit nutritional quality under salt stress were studied. The results showed that the seed germination and seedling growth of tomato that silencing of Sly-miR171d/e by short tandem target mimic (STTM) were better than those of wild-type (WT). Silencing of Sly-miR171d/e seeds maintained a high germination rate, while WT tomato seeds barely germinated under 50 mM NaCl stress. Under 100 mM NaCl stress, silencing of Sly-miR171d/e increased the expression of their target gene SlGRAS24 with increasing duration of salt stress, while they enhanced the antioxidant activity, reduced reactive oxygen species (ROS) accumulation, and enhanced the salt tolerance of tomato plant by regulating gibberellin (GA) level. Moreover, the preharvest and postharvest fruit nutritional quality under salt stress was also studied, and the results showed that silencing of Sly-miR171d/e increased soluble solids, lycopene, total carotenoids, Vitamin C, organic acids and phenolic substances in tomato fruit. The present study demonstrated that silencing of Sly-miR171d/e enhanced plant salt tolerance through the GA pathway, and improved fruit nutritional quality under salt stress.

The highest efficiency solar cell won in the efficiency race does not always give the most excellent annual energy yield in the real world solar condition that the spectrum is ever-changing. The study of the radiative coupling of the concentrator solar cells implied that the efficiency could increase by the recycle of the radiative recombination generated by the surplus current in upper junction. Such configuration is called by a super-multi-junction cell. We expanded the model in the concentrator solar cell to non-concentrating installation. It was shown that this super-multi-junction cell configuration was found robust and can keep the maximum potential efficiency (50 % in realistic spectrum fluctuation) up to 10 junctions. The super-multi-junction cell is also robust in the bandgap engineering of each junction. Therefore, the future multi-junction may not be needed to tune the bandgap for matching the standard solar spectrum, as well as relying upon artificial technologies like ELO (Epitaxial lift-off), wafer-bonding, mechanical-stacking, and reverse-growth, but merely uses up-right and lattice-matching growth technologies. We have two challenging techniques; one is the optical cap layer that may be the directional photon coupling layer in the application of the photonics technologies, and another is the high-quality epitaxial growth with almost 100 % of the radiative efficiency.

Detailed description of carbonate minerals different in magnesium content of Triassic dolomites were presented in this article. The tests were carried out to determine geochemical and miner-alogical features in the terms of their geoengineering properties. The following carbonate phas-es were identified: a low-Mg calcite, a high-Mg calcite, a proto-dolomite, an ordered dolomite and a huntite. The following research methods were used: microscopic analysis, X-Ray Diffrac-tion, X-Ray Fluorescence and Electron probe microanalysis. The samples were collected from the Tarnowice formation which is the lower part the profile of the Upper Muschelkalk. On the basis of the results the chemical formulas of carbonate phases were calculated. The ranges of Mg and Ca content were presented in formulas. The results indicate of Mg in low-Mg calcite ranges from 0.6 to 1.2%, in high-Mg calcite from 7.47 to 10.41%. In proto-dolomite it ranges from 10.96 to 11.78%. In ordered dolomite Mg content is stoichiometric value for dolomite – 13.18%. Due to the reduced Mg content in identified huntite (the value ranges from 13.62% to 17.76), this carbonate phase was named as de-huntite.

The method of doublet frequency distance (DFD-) maps was applied, here, for visualization of DNA sequence structures of yeast chromosomes. The colour scale “rainbow” of the Octave programming tool is well suited for such visualization. The DFD-maps are generated by comparison of the differences in the number of all base doublets in a shifting frame with all other positions of this frame in a regarded DNA sequence section. This procedure can be applied from DNA-sections of between a few hundred bases (bps) up to a complete chromosome with a million or more bps. An orthogonal DFD-map pattern dominates all chromosomes and its parts. It can be interpreted by a large number of successive mutation events during evolution. In contrast, diagonal patterns indicate duplications of sequence sections and multiple tandem repeats. These periodic structures are found in several chromosomes and are more or less regular or noised. The larger tandem repeat in the subtelomeric region of chromosome 12 presents a characteristic example of a nested multiple-repeat structure. Its pattern in the DFD-map illustrates obviously a temporal order of duplication and mutation events leading to a hierarchical sequence architecture.

X-ray diffraction (XRD) analysis of complex poly-atomic systems, especially of biomolecules, using ultra-short laser pulses (USP), is currently one of the most important fields of modern physics. The basis for interpreting and "deciphering" experimental data is the well-known theory of X-ray scattering, where the main parameter of USPs - its duration - is not taken into account. In the present work it is shown that for scattering of attosecond USPs on DNA and RNA trinucleotides the pulse length is the most important scattering parameter. In this case the diffraction pattern significantly changes with respect to the previously known scattering theory. The results obtained are extremely important in XRD when using attosecond pulses to study trinucleotides of DNA and RNA because using the previously known scattering theory which does not take into account the duration of USPs one can not correctly interpret and therefore "decode" DNA and RNA structures.

The cerebellum is an encephalic region classically known for its central role in the control of movement, although recent research has revealed its involvement in other cognitive and affective tasks. Several different pathologies are known to affect this structure, causing a wide range of behavioral and gait impairments. Intriguingly, although the neurodegenerative factors affect all Purkinje cells of the cerebellum uniformly, certain neurodegeneration patterns can be distinguished, in which some Purkinje cells persist longer than other cell types. Precisely, there is a cerebellar region, lobe X, which is more resistant to different types of neurodegeneration regardless of the injury. This work will review the main models of cerebellar degeneration, with special emphasis on this region, and aims to reveal a common origin for its resistance to neuronal death.

CD15 (Lewis X/Lex) is a fucosyl (3-fucosly-N-acetyl-lactosamine) moiety found on membrane proteins of various cancer cells. These include renal cancer, prostate and bladder cancers, acute leukemias, hepatocellular carcinoma, breast cancer and melanoma. The antigen plays an espe-cially significant role in renal cell carcinoma. Its high expression serves as a good prognostic marker for patients and high hopes are related to its use in the immunotherapy of the tumor. The biological role of CD15 is the interaction with E-, L- and P-selectins (adhesion molecules) and al-lowing for the adhesion with the endothelial cells. In this way, cancer cells start to interact with the endothelium of blood vessels and consequently move out from the blood flow to the sur-rounding tissues. The blockage of antigen’s function results in reduced metastatic potential. Moreover, the molecule may be a therapeutic target against cancer in monoclonal antibod-ies-based therapies. CD15s is a sialyl derivative of CD15, that possess its own unique characteris-tics. Unlike high expression of CD15, which is a prognostic factor in Hodgkin lymphoma, CD15s relate to poor prognosis for the patients. Due to the high abundance in cancer cells, CD15 is con-sidered as a marker of Cancer Stem Cells. This review presents a comprehensive description of the role of CD15 and CD15s in cancer development and metastasis and overviews the clinical appli-cations of the anti-CD15 therapy.

The stellar winds of the central stars of planetary nebulae play an essential role in planetary nebulae shaping. In the interacting stellar winds model, the fast stellar wind injects energy and momentum which are transfered to the nebular envelope through an X-ray-emitting hot bubble. Together with other physical processes, such as the ionization of the nebular envelope, the asymmetrical mass-loss in the AGB, and the action of collimated outflows and magnetic fields, the presurized hot gas determines the expansion and evolution of planetary nebulae. \emph{Chandra} and \emph{XMM-Newton} have provided us with detailed information of this hot gas. Here in this talk I will review our current understanding of the effects of the fast stellar wind in the shaping and evolution of planetary nebulae and give some hints of the promissing future of this research.

Tungsten oxides play a pivotal role in a variety of modern technologies e.g., switchable glasses, wastewater treatment, and modern gas sensors. Metallic tungsten is used as armor material, for e.g., gas turbines as well as future fusion power devices. In the first case, oxides are desired as functional materials, while in the second case, oxides can lead to catastrophic failures, so avoiding the oxidation of tungsten is desired. In both cases, it is crucial to understand the reactivity of tungsten oxides with other chemicals. In this study, the different reactivities of tungsten oxides with the highly-oxophilic beryllium are studied and compared. Tungsten-(IV)-oxide and tungsten-(VI)-oxide layers are prepared on a tungsten substrate. In the next step, a thin film of beryllium is evaporated on the samples. In consecutive steps, the sample is heated in steps of 100 K from r. t. to 1273 K. The chemical composition is investigated after each experimental step by high-resolution X-ray photoelectron spectroscopy (XPS) of all involved core levels as well as the valence band. A model is developed to analyze the chemical reactions after each step. In this study, we find that tungsten trioxide was already reduced by beryllium at r. t. and started to react to form the ternary compounds BeWO₃ and BeWO₄ at temperatures starting from 673 K. However, tungsten dioxide is resistant to reduction at temperatures of up to 1173 K. In conclusion, we find WO₂ to be much more chemically resistant to the reduction agent Be than WO₃.

Bisphenol F (BPF) and bisphenol S (BPS) are increasingly used as substitutes for bisphenol A (BPA) in the plastic industry, driven by concerns over the adverse effects of BPA. However, there is a lack of infor-mation on the extent of exposure to these chemicals in children. This study aims to assess the extent of BPA, BPF, and BPS exposure and determine factors that influence such exposure. A group of Thai children (age 6-13 years, n=358) were recruited between October 2019-2020. Two first morning void was collected one week apart. Demographic and exposure-related information was gathered. Urinary concentrations of bisphenols were analyzed by liquid-chromatography and tandem mass spectrometry. Correlation between bisphenol concentrations and various factors was determined using generalized estimating equations with linear model. BPA, BPF, and BPS were detected at 79.6%, 31.0%, and 16.8%, with geometric mean (GM) concentrations of 1.41, 0.013, and 0.014 ng/mL respectively. Younger children aged < 10 years exhibited 1.3-1.6 times higher GM levels of all bisphenols compared to older children. Exposure to food stored in plas-tic containers were associated with higher levels of BPF and BPS. In conclusion, BPA was the most fre-quently detected bisphenol in urine samples from Thai children, followed by BPF and BPS.

To determine promethazine (PMZ) and its metabolites promethazine sulfoxide (PMZSO) and monodesmethyl-promethazine (Nor1PMZ) in swine muscle, fat, kidney, and liver, a sample preparation and high-performance liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis method were established and validated. The sample was extracted with 0.1% formic acid-acetonitrile, and the extract was purified with acetonitrile-saturated n-hexane. After concentration by rotary evaporation, the extract was re-dissolved in 0.1% formic acid-water and acetonitrile (80:20, v/v). The HPLC-MS/MS column used was a Waters Symmetry C18 (100 mm × 2.1 mm i.d., 3.5 μm), with 0.1% formic acid-water and acetonitrile as the mobile phase, and the target compounds were determined by positive ion scan and multiple reaction monitoring. PMZ and Nor1PMZ were quantified with deuterated promethazine (PMZ-d6) as the internal standard, while PMZSO was quantified by external standard method. The limits of detection (LOD) and limits of quantification (LOQ) of PMZ and PMZSO in muscle, liver, and kidney spiked samples were 0.05 μg/kg and 0.1 μg/kg, respectively, while those of Nor1PMZ were 0.1 μg/kg and 0.5 μg/kg, respectively. The LOD and LOQ of analytes in fat spiked sample were 0.05 μg/kg and 0.1 μg/kg, respectively. The sensitivity of this method reaches or exceeds its presented in previous reports. The analytes PMZ and PMZSO showed good linearity within the range of 0.1 μg/kg to 50 μg/kg, while Nor1PMZ showed good linearity within the range of 0.5 μg/kg to 50 μg/kg, with correlation coefficients (r) greater than 0.99. The recoveries of the target compounds in the sam-ples were between 81.73% and 107.17%, and the precision ranged from 1.78% to 10.47%. This study developed for the first time an HPLC-MS/MS method for the determination of PMZ and its metabolites PMZSO and Nor1PMZ in four swine edible tissues, comprehensively covered target tissues of monitoring object, which is applicable for monitoring veterinary drug residues in ani-mal-derived foods and ensuring food safety.

The classical human satellite DNAs, also referred to as human satellites 1, 2 and 3 (HSat1, HSat2, HSat3, collectively HSat1-3) constitute the largest individual arrays of tandemly repeated DNA sequences in the genome. Even though they were among the first human DNA sequences to be isolated and characterized at the dawn of molecular biology, HSat1-3 have been left behind in the genomics era and remain among the most enigmatic sequences in the human genome. Although HSat1-3 total roughly 3% of the genome on average, they were almost entirely missing from the human genome reference assembly for 20 years. Recently, the Telomere-to-Telomere Consortium produced the first truly complete assembly of a human genome, including the enormous HSat1-3 arrays, opening them up for a new wave of discovery. Towards this end, here, I provide an account of the history and current understanding of HSat1-3 genomics, evolution, and roles in disease.

Nuclear receptors (NRs) constitute a superfamily of ligand-activated transcription factors with a paramount role in ubiquitous physiological functions such as metabolism, growth, and reproduction. Owing to their physiological role and druggability, NRs are deemed attractive and valid targets for medicinal chemists. Pentacyclic triterpenes (PTs) represent one of the most important phytochemical classes present in higher plants, where oleanolic acid (OA) is the most studied PTs representative owing to its multitude of biological activities against cancer, inflammation, diabetes, and liver injury. PTs possess a lipophilic skeleton that imitates the NRs endogenous ligands. Herein, we report a literature overview on the modulation of metabolic NRs by OA and its semi-synthetic derivatives, highlighting their health benefits and potential therapeutic applications. Indeed, OA exhibited varying pharmacological effects on FXR, PPAR, LXR, RXR, PXR, and ROR in a tissue-specific manner. Owing to those NRs modulation, OA exhibited prominent hepatoprotective properties comparable to ursodeoxycholic acid (UDCA) in a bile duct ligation mice model and antiatherosclerosis effect as simvastatin in a model of New Zealand white (NZW) rabbits. It also demonstrated a great promise in alleviating non-alcoholic steatohepatitis (NASH) and liver fibrosis, attenuated alpha-naphthol isothiocyanate (ANIT)-induced cholestatic liver injury, and controlled blood glucose levels, making it a key player in the therapy of metabolic diseases. We also compiled OA semi-synthetic derivatives and explored their synthetic pathways and pharmacological effects on NRs, showcasing their structure-activity relationship (SAR). To the best of our knowledge, this is the first review article to highlight OA activity in terms of NRs modulation.

This study applied multiple scientific approaches to establish the significance of an old work of art, Red Guitar, by examining its historical origin and the color materials used in its creation. Furthremore, the study provides thus far unknown pieces of Olga Picasso's family history to be added to her biography. Scientific approaches included digital X-ray radiography, X-ray fluorescence spectroscopy, infrared Fourier transform spectroscopy, Raman spectroscopy, and elemental thermal conductivity analysis. This combination of techniques provided broad confirmation about the time when the painting was created. The work includes colors (white, black, blue, yellow, green, red, and brown/red) and prevalent use of lead-and iron-based historic pigments Chrome Yellow, Yellow Ochre and Red Ochre. It also documents the use of unconventional materials, the colorant Pigment red 4 and nitrocellulose. This investigation led to the conclusion that the art, Red Guitar, is genuine and in accord with Picasso’s work during the first two decades of the 20th century.

The following system of equations {x_1 \cdot x_1=x_2, x_2 \cdot x_2=x_3, 2^{2^{x_1}}=x_3, x_4 \cdot x_5=x_2, x_6 \cdot x_7=x_2} has exactly one solution in ({\mathbb N}\{0,1})^7, namely (2,4,16,2,2,2,2). Hypothesis 1 states that if a system of equations S \subseteq {x_i \cdot x_j=x_k: i,j,k \in {1,...,7}} \cup {2^{2^{x_j}}=x_k: j,k \in {1,...,7}} has at most five equations and at most finitely many solutions in ({\mathbb N}\{0,1})^7, then each such solution (x_1,...,x_7) satisfies x_1,...,x_7 \leq 16. Hypothesis 1 implies that there are infinitely many composite numbers of the form 2^{2^{n}}+1. Hypotheses 2 and 3 are of similar kind. Hypothesis 2 implies that if the equation x!+1=y^2 has at most finitely many solutions in positive integers x and y, then each such solution (x,y) belongs to the set {(4,5),(5,11),(7,71)}. Hypothesis 3 implies that if the equation x(x+1)=y! has at most finitely many solutions in positive integers x and y, then each such solution (x,y) belongs to the set {(1,2),(2,3)}. We describe semi-algorithms sem_j (j=1,2,3) that never terminate. For every j \in {1,2,3}, if Hypothesis j is true, then sem_j endlessly prints consecutive positive integers starting from 1. For every j \in {1,2,3}, if Hypothesis j is false, then sem_j prints a finite number (including zero) of consecutive positive integers starting from 1.

Tandem mass spectrometry (MS/MS) for diagnosing inborn errors of metabolism (IEM) is recognized as an ethical, safe, simple, and reliable screening test. Presented bibliometric analysis aims to describe the network structure of the scientific community in the study area at the level of countries, institutions, authors, papers, keywords, and sources; scientific productivity, directions, and collaboration efforts in a considered period (1991–2023.) Using the PRISMA method, we conducted a systematic search for articles reporting using MS/MS to screen for inherited metabolic disorders and inborn errors of metabolism collected from the Web of Science Core Collection (WOSCC.) A total of 451 articles out of 546, by 2,682 authors, published in 190 journals, with 15,440 citations in 8,181 citing articles, with an average citation of 34.24 per article, and an H-index of 64 were retrieved from the WOSCC. The research status of MS/MS in IEM screening was identified. The most relevant current research directions and future areas of interest were revealed: "selective screening for IEM," "new treatments for IEM," "new disorders considered for MS/MS testing," "ethical issues associated with newborn screening," "new technologies that may be used for newborn screening," "use of a combination of MS/MS and gene sequencing," etc.

An analytical method was established by HPLC-DAD-ELSD with C18-NH2 column tandem for the simultaneous determination of hydrophobic components atractylenolide I, II, III, atractylone and hydrophilic compounds glucose, fructose and sucrose in the dried rhizome of Atractylodes macrocephala Koidz (a natural raw material for health foods, Bai-Zhu aka. in Chinese). The method combines different separation capabilities of reversed-phase liquid chromatography and hydrophilic interaction liquid chromatography, can provide a new choice for the simultaneous determination of hydrophilic and hydrophobic compounds in traditional Chinese medicines and health foods. It provided a reference method for the quality control of Bai-Zhu. The results showed that the linear correlation coefficients of the established column tandem chromatographic method were all greater than 0.9990, the relative standard deviation was 0.1%-2.8%, and the average recovery was 96.7%-103.1%. The contents of atractylenolide I, II, III, atractylone, fructose, glucose, and sucrose in 17 batches of Baizhu were 172.3-759.8 μg/g, 201.4-612.8 μg/g, 160.3-534.2 μg/g, 541.4-8723.1 μg/g, 6.9-89.7 mg/g, 0.7-7.9 mg/g, and 1.2-21.0 mg/g, respectively.

In (Semigroup Forum 77: 325-338, 2008) Mahmoudi M. and Renshaw J. solved a study that covers of cyclic $S$-acts over monoids. This article is an attempt to initiate the covers of finitely generated $S$-acts. We give a necessary and sufficient condition for a monoid to have the properties that $n$-generated $S$-acts have strongly flat covers, Condition $(P)$ covers and projective covers. The main conclusions extend some known results. We show also that Condition $(P)$ covers of finitely generated $S$-acts are not unique, unlike the situation for strongly flat covers. Additionally, we demonstrate that the property of Enochs' $\mathcal{X}$-precover of $S$-act $A$, where $\mathcal{X}$ denotes a class of $S$-acts that are closed under isomorphisms.

Rett Syndrome (RTT) is a severe neurodevelopmental disorder predominately diagnosed in females and primarily caused by pathogenic variants in the X-linked gene Methyl-CpG Binding Protein 2 (MECP2). Most often, the disease causing MECP2 allele resides on the paternal X chromosome while a healthy copy is maintained on the maternal X chromosome with inactivation (XCI) resulting in mosaic expression of one allele in each cell. Preferential inactivation of the paternal X chromosome is theorized to result in reduced disease severity; however, establishing such a correlation is complicated by known MECP2 genotype effects and an age dependent increase in severity. To mitigate these confounding factors, we developed an age- and genotype-normalized measure of RTT severity by modeling longitudinal data collected in the US Rett Syndrome Natural History Study. This model accurately reflected individual increase in severity with age and preserved group-level genotype specific differences in severity allowing for the creation of a normalized clinical severity score. Applying this normalized score to a RTT XCI dataset revealed that XCI influence on disease severity depends on MECP2 genotype with a correlation between XCI and severity observed only in individuals with MECP2 variants associated with increased clinical severity. This normalized measure of RTT severity provides the opportunity for future discovery of additional factors contributing to disease severity that may be masked by age and genotype effects.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

Agricultural crops productivity is heavily influenced by the strength of their seeds. Current methods for testing seed vigor, such as the germination rate and tetrazolium test, rely on time-consuming human visual inspections. Computer Vision, a crucial technology in smart production processes, offers an automated alternative and is increasingly applied in digital agriculture processes. Here we propose a method that combines YOLOv8 and morphological analysis of seeds using X-ray images to aid seed quality analysts in classifying seed lots based on their physiological potential. We examined the internal morphology of three seed lots and generated X-ray images to train a YOLOv8-based model with a post-segmentation module. This model assessed various parameters such as the total seed area, area filled by the embryo and endosperm, length, width, and calculated the percentage occupied by the embryo and endosperm in relation to the total seed area. Subsequently, seeds were classified into four categories based on the internal area occupied by the endosperm and embryo. Our findings reveal the robust performance of the YOLOv8 model in segmenting and classifying despite the challenges posed by a relatively small dataset. Notably, the proposed model achieved an impressive accuracy of up to 95.6% in identifying and segmenting the endosperm over 1,500 epochs with just 15 training images. The endosperm/seed area ratio, particularly within the 50-60% range covering over 50% of the samples, emerged as a significant metric for evaluating the viability of seed batches.

Bottlebrush (BB) elastomers with water-soluble side chains and tissue-mimetic mechanical properties are promising for biomedical applications like tissue implants and drug depots. This work investigates the microstructure and phase transitions of BB elastomers with crystallizable polyethylene oxide (PEO) side chains by real-time synchrotron X-ray scattering. In the melt, the elastomers exhibit the characteristic BB peak corresponding to the backbone-to-backbone correlation. Upon crystallization of the side chains, the intensity of the peak decays linearly with crystallinity, and eventually vanishes due to BB packing disordering within intercrystalline amorphous gaps. This behavior of the bottlebrush peak differs from an earlier study of BBs with poly(ε-caprolactone) side chains, explained by stronger backbone confinement in the case of PEO, a high-crystallinity polymer. Microstructural models based on 1D SAXS correlation function analysis suggest crystalline lamellae of PEO side chains separated by amorphous gaps of monolayer-like BB backbones.

In this work we developed two new polyfunctional hybrid systems, in which the presence of Fc redox "antennas" on peptide scaffolds allows a modulation of their electronic properties. Specifically, we synthesized two helical hexapeptides containing four Aib (α-amionoisobutyric acid) and two L-Dap (2,3-diamino propionic acid) residues. L-Dap side chains were then functionalized with Fc moieties. The structures of the two 310 helical peptides, namely Z-Aib-L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr and Z-Aib-L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr, were investigated by X-ray diffraction, 2D-NMR, CD and IR spectroscopies. Due to the helical conformation, in Z-Aib-L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr the Fc groups are located on the same face of the helix, in Z-Aib-L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr on opposite faces. Surprisingly, two bands were found in DPV for Z-Aib- L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr, indicating electrostatic interaction between the Fc groups despite their longer reciprocal distance with respect to that in Z-Aib- L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr. CD experiments at different concentrations evidenced aggregation for Z-Aib- L-Dap(Fc)-Aib-L-Dap(Fc)-Aib-Aib-NH-iPr even at high dilution, thus suggesting that the Fc-Fc electrostatic interaction could be of intermolecular nature.

Background: Erythropoietic protoporphyria (EPP) and X-linked protoporphyria (XLP) are the two most common subtypes within rare genetic photodermatoses, which can lead to incapacitating pain episodes. Methods: We reviewed previous and current treatment options for EPP/XLP, notably with a focus on metabolism, pharmacokinetics, mechanism of action, key clinical trial results, and limitations of Dersimelagon [MT-7117]. Results: In review of treatment modalities for EPP/XLP, Dersimelagon has demonstrated an acceptable safety profile with the ease of once-daily oral dosage. Conclusions: Dersimelagon should be a considered as a potential treatment for EPP/XLP. Ongoing studies will provide additional insights into expanding the treatment options for those suffering from EPP/XLP.

The archival Rossi X-ray Timing Explorer (RXTE) Proportional Counter Array (PCA) observations of HZ Her/Her X-1 are analyzed here. The time periods for Anomalous Low States are refined. The 35-day X-ray lightcurve of Her X-1 is produced using 35-day phases determined with RXTE All-Sky Monitor (ASM) and Swift Burst Altert Telescope (BAT) data, with adjustments based on the RXTE/PCA data. The result is the highest sensitivity 35-day lightcurve of Her X-1. The RXTE/PCA data were separated into 8 differents states of the 35-day cycle: Main High (MH) turn-on, MH, MH decline, Low State (LS) 1, Short High (SH) turn-on, SH, SH decline, and LS2. Orbital lightcurves were created for each state, and the different states are compared. Eclipse data was extracted for each state to determine the changes of eclipse shape with 35-day phase. A scattering corona model was fit to the eclipses for the different 35-day states: this shows that the corona is present at all 35-day phases with similar intensity. We carried out a search for previously-reported dips with no absorption, but did not find any.

Purpose: We assessed if a CXR AI algorithm can detect missed or mislabeled chest radiographs (CXRs) findings in radiology reports. Methods: We queried multi-institutional radiology reports search database of 13-million reports to identify all CXRs reports with addendums from 1999-2021. Of the 3469 CXR reports with an addendum, a thoracic radiologist excluded reports where addendum was created for typographic errors, wrong report template, missing sections, or uninterpreted signoffs. The remaining reports with addendum (279 patients) with errors related to side-discrepancy or missed findings such as pulmonary nodules, consolidation, pleural effusions, pneumothorax, and rib fractures. All CXRs were processed with an AI algorithm. Descriptive statistics were performed to determine the sensitivity, specificity, and accuracy of AI to detect missed or mislabeled findings. Results: AI had high sensitivity (96%), specificity (100%), and accuracy (96%) for detecting all missed and mislabeled CXR findings. The corresponding finding-specific statistics for AI were nodules (96%, 100%, 96%), pneumothorax (84%, 100%, 85%), pleural effusion (100%, 17%, 67%), consolidation (98%, 100%, 98%), and rib fractures (87%, 100%, 94%). Conclusion: The CXR AI could accurately detect mislabeled and missed findings. Clinical Relevance: The CXR AI can reduce the frequency of errors in detection and side-labeling of radiographic findings.

Astronomical X-ray polarimetry was first explored in the end of the 60's by pioneering rocket instruments. The craze arising from the first discoveries on stellar and supernova remnant X-ray polarization led to the addition of X-ray polarimeters on-board of early satellites. Unfortunately, the inadequacy of the diffraction and scattering technologies required to measure polarization with respect to the constraints driven by X-ray mirrors and detectors, coupled to long integration times, slowed down the field for almost 40 years. Thanks to the development of new, highly sensitive, compact X-ray polarimeters in the beginning of the 2000's, the possibility to observe astronomical X-ray polarization is rising again and scientists are now ready to explore the high energy sky thanks to modern X-ray polarimeters. In the forthcoming years, several X-ray missions (both rockets, balloons and satellites) will open a new observational windows. A wind of renewal blows over the area of X-ray polarimetry and this paper presents for the first time a quantitative assessment, all based on scientific literature, of the growth of interest for astronomical X-ray polarimetry.

The flux growth of InVO4 bulk single crystals has been explored for the first time. The reported eutectic composition at a ratio of V2O5:InVO4 = 1:1 could not be used as a self-flux, since no sign of melting was observed up to 1100 °C. Crystals of InVO4 of typical size 0.5×1×7 mm3 were obtained using copper pyrovanadate (Cu2V2O7) as a flux, using Pt crucibles. XRD confirmed the orthorhombic Cmcm structure. Rests of flux material were observed on the sample surface, with occasional traces of Pt indicating some level of reaction with the crucible. X-ray absorption spectroscopy showed that oxidation states of indium and vanadium ions are +3 and +5, respectively. The size and high quality of the obtained InVO4 crystals makes them excellent candidates for the further study of their physical properties.

The development of novel coherent and brilliant sources, such as soft X-ray Free Electron Laser (FEL) and High Harmonic Generation (HHG) enables new ultrafast analysis of the electronic and structural dynamics of a wide variety of materials. Soft X-ray FEL delivers high brilliance beams with short pulse duration, high spatial coherence and photon energy tunability. In com-parison with FELs, HHG X-ray sources are characterized by a wide spectral bandwidth and few to sub-femtosecond pulses. The approach will lead to time-resolved reconstruction of molecular dynamics, shedding light on different photochemical pathways. The high peak brilliance of soft X-ray FELs facilitates investigations in nonlinear regime, while the broader spectral bandwidth of the HHG sources may provide the simultaneous probing of multiple components. Significant technical breakthroughs in these novel sources are under way to improve brilliance, pulse dura-tion, and to control spectral bandwidth, spot size, and energy resolution. Therefore, in the next few years, the new generation of soft X-ray sources combined with novel experimental tech-niques, new detectors, and computing capabilities will allow the study of several extremely-fast dynamics, such as vibronic dynamics. In the present review, we shortly discuss recent devel-opments in experiments, performed with soft X-ray FELs and HHG sources, operating near car-bon K-absorption edge, being a key atomic component in biosystems and soft materials. Differ-ent spectroscopy methods such as time-resolved pump-probe techniques, nonlinear spectrosco-pies and photoelectron spectroscopy studies have been addressed in an attempt of a better un-derstanding of fundamental physico-chemical processes

This paper presents the second stage of a tandem fixed wing unmanned aerial vehicle (UAV) aerodynamic development. In the initial stage, the UAV was optimized analyzing its characteristics only in symmetrical flight conditions. Posted requirements were that both wings should produce relevant positive lift, the initial stall must occur on the front wing first, the center of pressure should be close to the center of gravity, while longitudinal static stability should be in the optimum range. Computational fluid dynamics (CFD) analyses were performed, where applied calculation model was derived from the authors’ previous successful projects. The eight version TW V8 has satisfied all longitudinal requirements. Lateral-directional CFD analyses of V8 showed that the ratio of the lateral and directional stability at the nominal cruising regime was optimal, but both lateral and directional static stabilities were too high. On further development versions the lower vertical tail was eliminated, negative dihedral was implemented on the front wing, and four inverted blended winglets were added. Version TW V14 has largely improved lateral and directional stability characteristics, while their optimum ratio at cruising regime was preserved. Longitudinal characteristics were also well preserved. Maximum lift coefficient and lift-to-drag ratio were increased, compared to the V8.

Objective: Lipids are secreted into milk as bilayer-coated structures: milk lipid globules (MLGs). Adipophilin (ADRP) and perilipin 3 (TIP47) are associated with MLGs in human breast milk; however, the role of these proteins in milk lipid secretion is not fully understood. The aim of the study was to investigate levels of ADRP, TIP47 and total lipid content in human breast milk, their mutual correlations and dynamics during lactation. Research Methods & Procedures: Milk samples from 22 healthy lactating women (Caucasian, Central European) were collected at five time points during lactation (1–3, 12–14, 29–30, 88–90 and 178–180 days postpartum). Mass spectrometry-based method was used for quantification of ADRP and TIP47 in the samples. The gravimetric method was used to determine milk total lipid content. Results: We observed distinctive trends in ADRP, TIP47 levels and lipid content in human breast milk during the first 6 months of lactation. We also found a significant association between lipid content and ADRP, lipid content and TIP47, and ADRP and TIP47 concentrations in breast milk at all sampling points. Moreover, we derived an equation for estimating the mean lipid content of milk based on ADRP concentration in human breast milk. Conclusions: A mass spectrometry-based method was developed for quantifying ADRP and TIP47 in human breast milk. Strong mutual correlations were found between ADRP, TIP47 and total lipid content in human breast milk.

This paper serves as a seamless continuation of the previous work titled "Special Spirals are Produced by the ROTASE Galactic Spiral Equations with the Sequential Prime Numbers." Upon revisiting the data, a noteworthy observation emerged: the special spirals can be meticulously aligned with the prime spiral on a point-by-point basis through careful scaling and rotation for the parameter ρ remaining a constant greater than one. As ρ increases, both the scaling factor and rotation angle exhibit a corresponding augmentation, albeit with an intriguing caveat—the rotation angle asymptotically approaches its limit of 90°. Notably, the galactic spiral can be perceived as a remarkably close approximation of the Archimedean spiral, with the degree of proximity increasing as ρ grows larger. Furthermore, an intriguing correspondence arises when ρ takes on a value of 1; at this value, the galactic spiral bears a striking resemblance to the Fermat spiral, the space between two consecutive spiral loops undergoes a continuous reduction as the loop's radius expands, yet it never diminishes to zero; simultaneously, the area between two successive loops experiences an augmentation with the value of ρ.

Diastematomyelia, also known as split cord syndrome, is a congenital disorder of the spinal cord. As the name suggests, the spinal cord is split into two resulting in neurological complaints associated with cutaneous symptoms. Although the diagnosis can be done clinically, for disease confirmation, various radiological investigations are used for the diagnosis of this condition. Here, we present a case of a 54-year-old Indian female diagnosed with diastematomyelia. The clinical features, diagnostic modalities, treatment options and prognosis of this condition have been discussed.

Active-case finding (ACF) using chest X-ray is an essential method of finding and diagnosing TB cases that may be missed in Indonesia's routine TB case finding. This study compares active and passive TB case-finding strategies. A retrospective study of TB case notification was conducted. Data between January 1 and December 31, 2021, was used. The population in this study were TB cases notified from Kulon Progo District health facilities, including those found through routine activities or active-case finding. A total of 255 TB cases were diagnosed in Kulon Progo in 2021, and 106 (41.6%) were bacteriologically confirmed. The TB patients' mean age was 46.3 (SD 21.4, range 0-85 years). The majority of cases were male (58.8%) and mostly among people aged 16-60 years old (63.5%). ACF diagnosed 91 TB cases (35.7% total cases, 91/255). The proportion of clinical TB cases (n=68, 74.7%) among those found through ACF was higher than found through passive-case finding. Use of chest X-ray in ACF likely contributed to the detection of a higher proportion of clinical TB than bacteriologically confirmed.

Diamond powders with inclusions of europium atoms were synthesized at high pressure (7.7 GPa) and temperature (1800oC) from a mixture of pentaerythritol, C(CH2OH)4, and pyrolyzate of diphthalocyanine (C64H32N16Eu) served as a special precursor. In prepared diamonds by X-ray fluorescence spectroscopy, we have found the concentration of Eu atoms of 51±5 ppm that is by two orders of magnitude greater than that in known natural and synthetic diamonds. X-ray diffraction, SEM, X-ray exited optical luminescence, Raman and IR spectroscopy have confirmed the formation of diamond monocrystals of high quality with em-bedded Eu atoms and a nitrogen content of ~500 ppm. Numerical simulation has allowed us de-termine the energy cost of 5.8 eV needed for the incorporation of a single Eu atom with adjacent vacancy into growing diamond crystal (528 carbons).

Early in development, placental and marsupial mammals harbouring at least two X chromosomes per nuclei are faced with a choice that affects the rest of their lives: which of those X chromosomes to transcriptionally inactivate. This choice underlies phenotypical diversity in the composition of tissues and organs and in their response to environment, and can determine whether an individual will be healthy or affected by an X-linked disease. Here, we review our current understanding of the process of choice during X-chromosome inactivation and its implications, focusing on the strategies evolved by different mammalian lineages and on the known and unknown molecular mechanisms and players involved. We also call for a revised manner in which to think about choice during random X-inactivation.

The development of microelectronics is always driven by reducing transistor size and increasing integration, from the initial micron-scale to the current few nanometers. The photolithography technique for manufacturing the transistor needs to reduce the wavelength of the optical wave, from ultraviolet, deep, to the existing extreme ultraviolet light. One approach toward decreasing the working wavelength is using lithography based on beyond extreme ultraviolet radiation (BEUV) with a wavelength around 7 nm. The BEUV lithography relies on advanced reflective optics such as periodic multilayer film X-ray mirrors (PMMs). PMMs are artificial Bragg crystals having alternate layers of “light” and “heavy” materials. The periodicity of such a structure is relatively half of the working wavelength. Since a BEUV lithographical system contains at least 10 mirrors, optics’ reflectivity becomes a crucial point. The increasing of a single mirror's reflectivity by 10% will increase the system’s overall throughput by 6 times. In this work, the properties and development status of PMMs, particularly for BEUV lithography, were reviewed to gain a better understanding of their advantages and limitations. Emphasis was given to materials, design concepts, structure, deposition method, and optical characteristics of these coatings.

Microwave Power Modules (MPM) are high power devices largely used for radar applications. An MPM is a hybrid combination of a Solid-State Power Amplifier (SSPA) as a driver and a Traveling wave tube amplifier (TWT) as the final high power stage. Power equalizer is often used to flat the TWT output power gain owing to its big gain fluctuations in the operating frequency range. This paper deals with an optimal design and development of a fully-coaxial easy-tunable power equalizer for an X-band MPM. The structure utilizes a coaxial waveguide as the main transmission line and a coaxial cavity loaded with absorbing material as the resonant unit. A sensitivity analysis of the coaxial cavity length, the thickness of the absorbing disc and inserted depth of the probe on the attenuation amplitude and resonant frequency is carried out. The transmission characteristic curves and the voltage standing wave ratio curves show a good compromise in terms of transferred power and adaptive matching impedance at the input and output ports. The measured results show that the equalization curve meets the requirements well and prove that this structure is practical and effective.

Subversion of programmed cell death-based host defence systems is a prominent feature of infections by large DNA viruses. African swine fever virus (ASFV) is a large DNA virus and sole member of the Asfarviridae family that harbors the B-cell lymphoma 2 or Bcl-2 homolog A179L. A179L has been shown to bind to a range of cell death inducing host proteins including pro-apoptotic Bcl-2 proteins as well as the autophagy regulator Beclin. Here we report the crystal structure of A179L bound to the Beclin BH3 motif. A179L engages Beclin using the same canonical ligand binding groove that is utilized to bind to pro-apoptotic Bcl-2 proteins. The mode of binding of Beclin to A179L mirrors that of Beclin binding to human Bcl-2 and Bcl-xL as well as murine gamma-herpesvirus 68. Introduction of bulky hydrophobic residues into the A179L ligand binding groove via site directed mutagenesis ablates binding of Beclin to A179L, leading to a loss of ability of A179L to modulate autophagosome formation in Vero cells during starvation. Our findings provide a mechanistic understanding for the potent autophagy inhibitory activity of A179L and serve as a platform for more detailed investigations into the role of autophagy during ASFV infection.

The Upper Jurassic (Oxfordian Age) Smackover Formation is a significant source for hydrocarbon production in southwest Alabama. Brooklyn Field is in southeast Conecuh County, Alabama and has been a major producer of oil and natural gas for the state. The Smackover is a carbonate formation that is divided into seven distinct lithofacies. In southwest Alabama, the Smackover Formation is heavily influenced by paleotopography from the underlying Paleozoic rocks of the Appalachian system. The goal of this study is to determine elemental ratios in rock core within the Smackover Formation using a X-ray fluorescence (XRF) handheld scanner, to correlate between lithofacies in the Smackover Formation and elementally characterize the upper oolitic grainstone reservoir and the lower thrombolite boundstone. Eight wells were used for the study within Brooklyn Field and Little Cedar Creek fields. Cores from the eight wells were scanned on six-inch intervals. Chemical logs were produced to show elemental weights in relation to depth and lithofacies. Well data collected for chemical signatures within producing zones were correlated to reservoir lithofacies and porosity. Aluminum, silicon, calcium, titanium, and iron were the most significant (>95% confidence level) predictors of porosity and is related to the depositional environment and subsequent diageneses of the strata. XRF data suggests relative enrichments in iron, titanium, and potassium may be related to deposition in relatively restricted marine waters.

The three-point bending behavior of a single Au nanowire deformed with an atomic force microscope was monitored by coherent X-ray diffraction using a sub-micrometer sized hard X-ray beam. While three-dimensional reciprocal-space maps were recorded before and after deformation by standard rocking curves, they were measured by scanning the energy of the incident X-ray beam during deformation at different loading stages. The mechanical behavior of the nanowire is visualized in reciprocal space and a complex deformation mechanism is described. In addition to the expected bending of the nanowire, torsion is detected. Bending and torsion angles are quantified from the high resolution diffraction data.

The analysis of particulate matter (PM) in dilute solutions is an important target for environmental, geochemical and biochemical researches. Here we show how the microdrop technology may allow to control, through the evaporation of small droplets, the deposition of insoluble materials dispersed in a solution on a well-defined area with a specific spatial pattern. Using this technology the superficial density of the deposited solute can be accurately controlled. In particular, it becomes possible to deposit an extremely reduced amount of insoluble material -in the order of few μg- on a confined area, thus allowing a relatively high superficial density to be reached within a limited time. In this work we quantitatively compare the microdrop technique for the preparation of particulate matter samples with the classical filtering technique. After having been optimized, the microdrop technique allows to obtain a more homogeneous deposition and limit sample consumption of a factor ~25. This method is potentially suitable for many novel applications in different scientific fields.

Abstract: Comparing outcrop data to laboratory results is important to verify and validate experiments of analogue and reservoir materials especially regarding conditions for deformation experiments. This is important better understand highly complex carbonate reservoir strata and their response to changes in subsurface conditions, reducing subsurface uncertainty. This study develops methods to allow for a more straightforward comparison of outcrop data (m-scale) with experimentally created fracture arrays developed in cylindrical samples (cm-scale). The main objective is to assess usefulness of experimentally-produced fracture networks as analogues for subsurface structures, typically at the meter and above scale by developing new techniques to use the lab deformation. It analyses key characteristics of laboratory-induced fracture networks by adapting scanline methods to use with x-ray tomography (XRT) images to allow for comparison with outcrop and field data. To test and verify these new methods two low permeability carbonate samples were used for deformation testing and analysis. Applying the different scanline methods we show that they can be used to analyse lab induced fractures (mm to cm-scale) identified in XRT images for comparison with outcrop data (m-scale). In addition, these methods also allow for quantification of fracture network attributes e.g. fracture spacing, fracture apertures, orientation. This new data bridges the gap between micro-scanlines using thin sections and outcrop scanlines.

The structure of arylpiperazine moieties as an important pharmacophore could generate wide pharmacological activities．Arylpiperazine derivatives referred in this paper possessed antitumor activity. The title compounds were crystallized by slow evaporation. 2-(4-(2-(4-Phenylpiperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione(1), 2-(4-(2-(4-(4-Bromophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (2) and 2-(4-(2-(4-(4-Chlorophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (3) crystallizes in the triclinic space group P-1 with two molecules in the unit cell. The unit cell parameters for 1 are a = 6.9159(14) Å, b = 9.999(2) Å, c = 16.925(3) Å, α = 88.25(3)°, β = 85.14(3) °, γ = 79.22(3) °. The unit cell parameters for 2 are a = 6.9995(14) Å, b = 9.919(2) Å, c = 17.671(4) Å, α= 97.55(3)°, β = 92.19(3) °, γ = 102.23(3) °. The unit cell parameters for 1 are a = 6.9872(14) Å, b = 9.863(2) Å, c = 17.557(4) Å, α=96.81(3)°, β = 91.89(3) °, γ = 101.74(3) °. Pi-pi interactions were observed between molecules, and compound 2 and 3 showed halogen interactions between molecules nearby, which was different from compound 1.

Abstract Octreotide is the first synthetic peptide hormone, consisted of eight amino acids, that mimics the activity of somatostatin, a natural hormone in the body. During the past decades, advanced instrumentation and crystallographic software established X-ray Powder Diffraction (XRPD) as a valuable tool for extracting structural information of biological macromolecules. The latter was demonstrated by the successful structural determination of octreotide at a remarkably high d-spacing resolution (1.87 Å) (PDB code: 6vc1). This study focuses on the response of octreotide to different humidity levels and temperatures, with a particular focus on the stability of the polycrystalline sample. XRPD measurements were accomplished employing an Anton Paar MHC-trans humidity-temperature chamber installed within a laboratory X’Pert Pro diffractometer (Malvern Panalytical). The chamber is employed to control and maintain precise humidity and temperature levels of samples during XRPD data collection. Pawley analysis of the collected data sets revealed that the octreotide polycrystalline sample is remarkably stable and no structural transitions were observed. The compound retains its orthorhombic symmetry (space group: P212121, a = 18.57744(4) Å, b = 30.17338(6) Å, c = 39.70590(9) Å, d~ 2.35 Å). However, a characteristic structural evolution in terms of lattice parameters and volume of the unit-cell is reported mainly upon controlled relative humidity variation. In addition, an improvement of signal-to-noise ratio in the XRPD data under a cycle of dehydration/rehydration is reported. These results underline the importance of considering the impact of environmental factors, as humidity and temperature, in the context of structure-based drug design, thereby contributing to the development of more effective and stable pharmaceutical products.

Neutron computed tomography (nCT) has been established at many major neutron sources worldwide, using high-end equipment requiring major investment and development. Many older and smaller reactors would be capable of doing nCT as well, but cannot afford the investment before feasibility is proven. We have developed a compact low-cost but high-quality detection system using a new cooled CMOS camera that can either be fully integrated into a sophisticated setup, or used with a rudimentary CT control and motion system to quickly evaluate feasibility of neutron CT at a given beam line facility. Exchanging the scintillation screen makes it feasible for X-rays as well, even for visible light (and transparent samples) using a matte screen. The control system uses a hack to combine motion control with existing imaging software so it can be used to test several dozen different cameras without writing specific drivers. Freeware software can do reconstruction and 3D imaging.

Man-made shallow fishponds in the Czech Republic have been facing a high eutrophication since 1950s. Anthropogenic eutrophication and feeding of fish have strongly affected the physico-chemical properties of water and its aquatic community composition leading to harmful algal bloom formation. In our current study, we have characterised the phytoplankton community across three hypertrophic ponds to assess the phytoplankton dynamics during the vegetation season. We microscopically identified and quantified 29 cyanobacterial taxa comprised of non-toxigenic and toxigenic species. Further, a detailed cyanopeptides (CNPs) profiling was performed using molecular networking analysis of liquid chromatography tandem mass spectrometry (LC–MS/MS) data coupled with dereplication strategy. This MS networking approach coupled with dereplication on online global natural product social networking (GNPS) web platform led us to putatively identify forty CNPs: fourteen anabaenopeptins, ten microcystins, five cyanopeptolins, six microginins, two cyanobactins, a dipeptide radiosumin, a cyclooctapeptide planktocyclin and epidolastatin12. We have applied the binary logistic regression to estimate the CNPs producer by correlating the GNPS data with the species abundance. Usage of The combination of molecular networking and dereplication on online global natural product social networking (GNPS) web platform has proved as a valuable approach for rapid and simultaneous detection of high number of peptides, and rapidly assessing the risk for harmful bloom.

Systemic sclerosis (SSc) is an autoimmune connective tissue disease characterized by debilitating symptoms including skin and visceral fibrosis, systemic skin hardening, Raynaud's phenomenon and other vascular dysfunctions, and immune abnormalities. The disease poses a significant medical challenge with no cure currently available. As such, SSc is designated as an intractable disease in Japan, with patients receiving government subsidies for medical expenses. Oxidative stress (OS) is implicated in the pathogenesis of SSc and the antioxidant combination Tweendee X®︎ (TwX) has shown promising results in mitigating OS-related conditions. HOCl-induced SSc-mice are known to exhibit similar skin and visceral fibrosis, vascular disorders, and autoimmunity observed in human. In a study done using these mice, Twx demonstrated a significant reduction in lung and skin fibrosis compared to untreated HOCl-induced SSc mice. TwX also significantly reduced advanced oxidized protein products (AOPP) in serum, Col-1 gene expression and the activation of B cells involved in autoimmunity. SSc is a disease state in which autoimmune abnormalities, fibrosis, and vascular disorders are intertwined, and therefore for a treatment to be effective it needs to address multiple issues. Thus the efficacy of TwX may stem from its strong antioxidant capacity to regulate OS, which cannot be achieved by a single antioxidant on its own. In other studies, targeting other OS-related conditions, TwX was safe and proved to be effective at prevent dementia in humans with mild cognitive impairment and to significantly improve cognitive impairment in Alzheimer's (AD) mouse models. TwX may offer a new approach to antioxidant treatment for SSc, to address multiple abnormalities that are characteristic of the disease.

This article aims to detect lung cavitations using lung ultrasound (LUS) in a cohort of patients with pulmonary tuberculosis (TB) and correlate the findings with chest computed tomography (CT) and chest x-ray (CXR) to obtain LUS diagnostic sensitivity. Patients with suspected TB were enrolled after being evaluated with CXR and chest CT. A blinded radiologist performed LUS within 3 days after the admission at the Infectious Diseases Department. Finally, 82 patients were enrolled in the study. BAL confirmed TB in 58/82 (71%). Chest CT showed pulmonary cavitations in 38/82 (43.6%; 32 TB patients and 6 non-TB ones), LUS in 15/82 (18.3%; 11 TB patients and 4 non-TB ones) and CXR in 27/82 (33%; 23 TB patients and 4 non-TB ones). Patients with multiple cavitations were 12 detected at CT and only 1 at LUS. LUS sensitivity was 39.5%, specificity 100%, PPV 100%, NPV 65.7%. CXR sensitivity was 68.4% and specificity 97.8%. No false positive cases were found. LUS sensitivity is rather low as many cavitated consolidations do not reach the pleural surface. Aerated cavitations could be detected with LUS with relative confidence, highlighting a thin air-crescent sign towards the pleural surface within a hypoechoic area of consolidation, easily distinguishable from dynamic or static air-bronchogram.

The valve controlled cylinder drive system is the most common type among hydraulic applications. The nonlinear behaviour in such system is inevitable when the valve spool around its null position [1] , Leaney [2] utilised component linking method to investigate the nonlinearities in a Moog valve controlled asymmetric cylinder drive system by simulation in Fortran, in which a generalised concept is introduced and validated by comparing to the experimental results. An factor is proposed in the generalised concepts to describe the asymmetric cylinder state, which is a constant when the cylinder in extending or retracting, but numerically calculated when the valve spool in the underlap region [2]. This paper utilises the component linking method to simulate the Moog valve controlled asymmetric cylinder drive system in Matlab Simulink, and proposed an analytical solution for factor when the valve spool in the underlap region.

Our daily activities hinge on the flexibility of our fingers, and a fractured finger can significantly disrupt these routines. The finger bones enable us to bend and fold the fingers and thumb to pick up or grasp objects and do all of our daily activities. A broken finger can cause adverse effects on our daily life activities. It is important to treat broken finger as soon as possible. Swift and precise treatment begins with capturing multiple X-rays, followed by the critical step of fracture detection in these images. Relying on the naked eye for this task carries the risk of overlooking small fractures. To address this issue an automated diagnoses of fractured fingers from images is required for which the current research employs advanced deep learning models—ResNet34, ResNet50, ResNet101, ResNet152, VGG-16, and VGG-19—to classify finger images from the Musculoskeletal Radiographs (MURA) dataset as either fractured or non-fractured. The results emphasize the consistently strong performance of ResNet models, attaining an impressive accuracy of 81.9%. This surpasses VGG models by 3.4% and establishes ResNet as the new benchmark for state-of-the-art accuracy.

Conductive hearing losses are typically present in disorders of the external/middle ear. However, there is a rare group of inner ear conditions called third windows that can also generate a conductive hearing loss. This is due to an abnormal connection between the middle and the inner ear or between the inner ear and the cranial cavity. X-linked gusher disorder is an extremely rare congenital inner ear dysplastic syndrome with such an abnormal connection due to a characteristic incomplete cochlear partition type 3 and an incomplete internal auditory meatus fundus. The disorder is inherited in an X-linked fashion due to the mutation of the POU3F4 gene. We present 2 siblings diagnosed with the condition and their long term follow ups. They both presented with audiovestibular symptoms and showed progressive mixed losses and bilateral vestibular weakness. They were treated with cochlear implant, digital amplification and with vestibular rehabilitation. Significant others around them were involved in their journey with the medical team and in both, a very favourable outcome was achieved. This is the first time that we are reporting evolving audiovestibular function with vestibular quantification in X-linked gusher disorder and emphasize on the multidisciplinary holistic approach to manage these children effectively.

The details of the solar flare production mechanisms are not yet completely understood. One of the standing questions is the anisotropy of the X-ray flux, especially in strong flares. It can be studied indirectly by analysing the characteristics of flares at different positions on the visible disc. In this paper, the durations, peak and integral fluxes of strong (X-class) solar flares from cycles 22--25 are considered with respect to their apparent position on the Sun. It is found that there exists a significant north--south asymmetry in all three parameters, which also varies depending on the phase of the solar cycle (with general predominance of the south). This confirms the results of previous studies. A weaker and less significant east--west asymmetry is found as well, partly supported by literature. A previously undetected centre-to-limb asymmetry is reported (in favour of the limb) in all three parameters. All three asymmetries are enhanced during the solar minimum, which could hint at their connection to the large scale magnetic structuring of the Sun. The prevalence of strong solar flares near the limb at the solar minimum has clear space weather warning implications.

21-hydroxylase deficiency (21OHD), the most common form of congenital adrenal hyperplasia (CAH), is associated with pathogenic variants in CYP21A2 gene. The clinical form of the disease ranges from classic or severe to non-classic (NC) or mild late onset. The CYP21A2 gene is located on the long arm of chromosome 6, within the RCCX region, one of the most complex loci in the human genome. The 3’untranslated sequence of CYP21A2 exon 10 overlap the last exon of TNXB gene (these genes lie on the opposite strands of DNA and have the opposite transcriptional direction) that encodes an extracellular matrix glycoprotein tenascin-X (TNX). A recombination event between TNXB and its pseudogene TNXA causes a 30-kb deletion producing a chimeric TNXA/TNXB gene (CAH-X chimera) where both CYP21A2 and TNXB genes are impaired. This genetic condition characterizes a subset of patients with 21OHD who display the hypermobility phenotype of Ehlers Danlos Syndrome (hEDS) (CAH-X Syndrome). The aim of this study was to assess the prevalence of CAH-X syndrome in an Italian cohort of patients with 21OHD. At this purpose, 196 probands were recruited. Multiplex ligation-dependent probe amplification (MLPA) and Sanger sequencing were used to identify the CAH-X genotype. Twenty-one individuals showed the heterozygous continuous deletion involving the CYP21A2 and part of the TNXB gene. EDS-related clinical manifestations were identified in most patients carrying the CAH-X chimera. A CAH-X prevalence of 10.7% was estimated in our population.