Abstract: In this study the semi-distributed model SWAT (Soil and Water Assessment Tool), were applied to evaluate stream flow of Didessa sub basin, which is one of the major sub basins in Abay river basin of Ethiopia. The study evaluated the quality of observed meteorological and hydrological data, established SWAT hydrological model, identified the most sensitive parameters, evaluated the best distribution for flow and developed peak flow for major tributary in the sub basin. The result indicated that the SWAT model developed for the sub basin evaluated at multi hydro-gauging stations and its performance certain with the statistical measures, coefficient about determination (R2) and also Nash coefficient (NS) with values ranging 0.62 to 0.8 and 0.6 to 0.8 respectively at daily time scale. The values of R2 and NS increases at monthly time scale and found ranging 0.75 to 0.92 and 0.71 to 0.91 respectively. Sensitivity analysis is performed to identify parameters those were most sensitive for the sub basin. CN2, GWQMN, CH_K, ALPHA_BNK and LAT_TIME are the most sensitive parameters in the sub basin. Finally, the peak flow for 2-10000 returns periods were determined after the best probability distribution is identified in EasyFit computer program.

Infection of liver flukes (Opisthorchis viverrini) is partly due to their suitability for habitats in sub-basin areas, which causes the intermediate host to remain in the watershed system in all seasons. Spatial monitoring of fluke infection at the small -basin analysis scale is important because this can enable analysis at the level of the spatial factors involved and influencing infections. A geographic weighted regression model was developed to analyze the spatial characteristics of liver fluke infection, aiming to 1. analyze the spatial factors associated with human liver fluke infection according to sub-basin boundaries and 2. generate an alternative model for enhancing the effectiveness of preventive public health management to reduce the risk of liver fluke infection in humans. The number of infected persons was obtained from local authorities and converted into a percentage of infected people and generated as raster data with a heat map so that the data were continuous and defined as dependent variables. The independent set consisted of nine variables, both vector and raster data, that correlated the location with the village location of an infected person. The results showed that the variables X5stream, X7ndmi, and X9savi were statistically significantly correlated to the percentage of infected people, with the t-stat and p-value being (-2.068, 1.875, and -2.661) and (0.048, 0.034, and 0.021), respectively. The GWR model was able to increase accuracy more than the comparable models such as OLS, in all tests of the four alternative models, with an accuracy increase in R2 of 7.69% (0.576 to 0.624). This study confirms that the development of spatial models with GWR models can screen for factors associated with liver fluke infection at the level of small spatial units such as sub-basins.

Land use and land cover change (LULCC) is a critical factor for enhancing the soil erosion risk and land degradation process in the Wabi Shebelle Basin. Up-to-date spatial and statistical data on basin-wide erosion rates can provide an important basis for planning and conservation of soil and water ecosystems. The objectives of this study were to examine the magnitude of LULCC and consequent changes in the spatial extent of soil erosion risk, and identify priority areas for Soil and Water Conservation (SWC) in the Erer Sub-Basin, Wabi Shebelle Basin, Ethiopia. The soil loss rates were estimated using an empirical prediction model of the Revised Universal Soil Loss Equation (RUSLE) outlined in the ArcGIS environment. The estimated total annual actual soil loss at the sub-basin level was 1.01 million tons in 2000 and 1.52 million tons in 2018 with a mean erosion rate of 75.85 t ha^–1 y^–1 and 107.07 t ha^–1 y^–1, respectively. The most extensive soil loss rates were estimated in croplands and bare land cover, with a mean soil loss rate of 37.60 t ha^–1 y^–1 and 15.78 t ha⁻¹ y⁻¹, respectively. The soil erosion risk has increased by 18.28% of the total area, and decreased by 15.93%, showing that the overall soil erosion situation is worsening in the study area. We determined SWC priority areas using the Multi-Criteria Decision Rule (MCDR) approach, indicates that the top three levels identified for intense SWC account for about 2.50%, 2.38%, and 2.14%, respectively. These priority levels are typically situated along the steep slopes in Babile, Fedis, Fik, Gursum, Gola Oda, Haramaya, Jarso, and Kombolcha districts that need emergency SWC measures.

The main target of this study was to evaluate the impact of future climate change on the available surface water resources in the Dhidhessa Sub-basin, Abbay Basin, Ethiopia. For the prediction, high-resolution Regional Climate Models (RCMs) from multiple climate models with data from Representative Concentration Pathways (RCPs) prepared by the CCAFS were used. The predictions of future discharge (stream flow) were based on climate scenarios data of baseline period of 1991 to 2020 and for the future with two time windows, 2044 (2030–2059) and 2084 (2070–2099), on a monthly time step after bias correction was conducted to both precipitation and temperature in the future climate under each RCP scenario. After sensitivity analysis, calibration (1994–2011), and validation (2012–2020) of the model for the Dhidhessa Sub-basin with the SUFI-2 program in the SWAT-CUP model, the SWAT model was used to determine water balance and stream flow from the SWAT model system. The SWAT model performed well in predicting stream flow in the Dhidhessa Sub-basins, with a coefficient of determination (R2) ranging from 0.8 to 0.94 and a Nash Sutcliffe value (NSE) ranging from 0.76 to 0.89. The percent decrease in mean annual stream flow from 2044 and 2084 were 10 %, in 2044, and 6.3% in 2084 respectively. The seasonal result under short-term 2044 of stream flow present change significantly decreased in spring, winter, and autumn with 20.2%, 67.4%, and 67.4% respectively. While summer season increased by 43.1%, under short-term 204. In long-term 2084 percent change declined except summer seasons, with 14.7%, 58.1%, and 3.3%, change in spring, winter, and autumn, respectively, and summer, with 51.1% increased and With RCP4.5 (1.64%) and RCP8.5 (2.1%) changed. In the future Dhidhessa stream flow increases and decreases from the baseline era. The decreasing stream flow in 2044 and 2084 will negatively affect agricultural production. This study revealed that any effect on this river resulting in a drop in flow will have a direct impact on ongoing water resource development and socio-economic development of the area.

This article utilized electrodeposition technology to fabricate Zn and Zn-Y₂O₃-Al₂O₃ composite coatings on Q235 steel plates. The composite coatings were obtained by adding Y₂O₃/Al₂O₃ nanoparticles (0, 5, 10, and 15 g/L) to acidic chloride solutions. This study then examined the impact of these nanoparticles on the microstructure, morphology, microhardness, hydrophobicity, and corrosion resistance of the composite coatings. The results indicate that the addition of the nanoparticles increased the nucleation sites on the surface of the coating, thereby refining the grain size and reducing the roughness of the coating surface. When 10g/L of Y₂O₃ and 10g/L of Al₂O₃ nanoparticles were added, the hardness of the composite coating (369 Hv) was 2.49 times higher than that of the pure Zn coating (148 Hv), which was attributed to the dispersion strengthening and grain refinement effects of the nanoparticles. The corrosion resistance of the Zn and Zn-Y₂O₃-Al₂O₃ composite coatings was studied using linear sweep voltammetry and AC impedance spectroscopy. The addition of the nanoparticles improved the corrosion resistance of the composite coating, and the composite coating prepared in an electrolyte containing 10 g/L of Y₂O₃ and 10 g/L of Al₂O₃ nanoparticles exhibited the best corrosion resistance. Meanwhile, the composite coating exhibited good hydrophobicity, with a contact angle of 120.9°, 1.94 times that of the pure Zn coating (62.2°). The Zn-Y₂O₃-Al₂O₃ nanocomposite coating material has significant potential advantages in the field of steel corrosion.

This case study focuses on exploring the potential of biogas as a direct substitute for conventional fossil fuels in industrial applications. Instead of being limited to its common uses as a vehicle fuel or for power generation, this research aims to investigate how biogas can be integrated into industrial processes as an advanced and sustainable energy solution. By conducting a detailed analysis of the financial implications associated with the utilization of landfill gas and gas derived from biomass, a comprehensive understanding of their practical applications in the industrial sector can be obtained. This research goes beyond a superficial examination and delves into the intricate aspects of incorporating biogas as a viable alternative fuel source. When we say that utilizing biogas is technically feasible, it means that the necessary infrastructure and technologies are available to support its integration into industrial processes. This implies that there are existing methods and systems in place that can efficiently harness and utilize biogas for various industrial applications. These technologies ensure a seamless transition from conventional fossil fuels to renewable energy sources, leading to a more sustainable and environmentally friendly industrial landscape. Moreover, the statement that utilizing biogas is economically feasible emphasizes that the financial viability of employing biogas in industrial processes is advantageous. This research explores the potential cost savings and benefits associated with substituting conventional fuels with biogas. By carefully examining the economic aspects, such as initial investments, operational costs, and potential revenue streams, a comprehensive understanding of the financial impact of adopting biogas solutions in the industrial sector can be gained. By expanding and broadening the understanding of the technical and economic feasibility of biogas integration, this research aims to provide valuable insights into the potential of advanced biogas solutions for industrial applications. Indeed, to make biogas a viable and sustainable option as a raw material, it is necessary to establish farming subsidies and financial support specifically tailored for biogas production, similar to the existing support provided for food production. These subsidies and financial incentives play a crucial role in promoting and encouraging the growth of the biogas industry. By establishing such support systems, farmers and other stakeholders in the agricultural sector can be incentivized to participate in the production of biogas. This can involve the utilization of agricultural waste, organic residues, or dedicated energy crops for biogas generation. The financial assistance can help offset the initial investment costs, provide incentives for production, and ensure the economic viability of biogas projects. Moreover, when considering large-scale landfills or situations where industrial demands for energy are relatively low, landfill gas becomes a viable and practical option. Landfill gas, which is generated by the decomposition of organic waste in landfills, can be harnessed and utilized for various industrial purposes. This not only helps in managing waste but also provides a valuable source of renewable energy. In summary, while farming subsidies and financial support are crucial for promoting biogas production, landfill gas remains a viable option for large landfills or situations with minor industrial demands. The combination of these two approaches offers a comprehensive outlook on utilizing biogas as a renewable energy source for industrial applications.

Background and Objectives: Cardiovascular events are the leading cause of morbidity and mortal-ity in hemodialysis (HD) patients. Identifying risk factors can help in the effort to reduce cardi-ovascular risk and improve life expectancy. The purpose of this study was to evaluate the ability of CHA2DS2-VASc score [risk index of stroke in atrial fibrillation (AF)] in patients with end stage kidney disease, to predict stroke, major cardiovascular events and mortality. Materials and Meth-ods: CHA2DS2-VASc and HAS-BLED (bleeding risk from use of anticoagulation in AF) scores were calculated in 237 HD patients, [99 women, median age 76 (15) years], at time they com-menced on HD. The scores’ ability to predict long term cardiovascular morbidity and mortality was estimated, both in those with and without AF. Results: CHA2DS2-VASc score was signifi-cantly increased in AF (n=69) compared to non-AF (n=168) patients, 5 (2.5) versus 4 (2), p<0.0001, respectively. Increased CHA2DS2-VASc score was associated with heart failure (p=0.007, p=0.024), stroke (p<0.0001, p<0.0001) and risk of all-cause mortality (p<0.0001, p<0.0001), in both groups, respectively. C statistics indicated that CHA2DS2-VASc score performed modest discrimination in this HD population with and without AF for heart failure, stroke, and all-cause mortality, but for cardiovascular mortality in AF group only. Conclusions: Increased CHA2DS2-VASc score at time starting on HD, can predict stroke, heart failure and all-cause mortality in HD patients in-dependent of the presence of AF. Risk of cardiovascular mortality could be predicted only on patients with AF.

This article systematically reviews the research achievements on the MnOx/TiO2 catalyst doped with transition metals or rare earth metals for the catalytic selective catalytic reduction of NH3 (SCR-NH3) reaction. The Methodi Ordinatio systematic literature analysis method was employed to rank relevant articles based on journal impact factors, publication years, and citation counts. The ranking data shows that the undoped MnOx/TiO2 catalysts exhibit a catalytic efficiency of up to approximately 90% for NOx reduction, while the doped MnOx/TiO2 catalysts with transition metals or rare earth metals can achieve a maximum reduction efficiency of 100%. Among all the doped metals, the catalyst doped with nickel demonstrates the best NOx reduction performance. The comprehensive literature research concludes that MnOx/TiO2-based SCR catalysts, especially those doped with transition metals or rare earth metals, have significant catalytic efficiency and development potential in reducing NOx emissions in SCR reactions.

Brazil has a large availability of natural resources and its economy was historically built around their exploitation. Changes in climate trends are already causing several environmental impacts, which affect the economic and social organization of the country. Impacts linked to the hydrological cycle are particularly concerning since water resources are used for electricity production, representing approximately 65% of the Brazilian electricity matrix. This study, therefore, aims to evaluate the hydroclimatic extreme trends of river basins located in the Northeast and South regions of the country. For this purpose, we carried out a flow analysis from 2020 to 2100, considering the precipitation data from the BCC CSM1-1, CCSM4, MIROC5, and NorESM1-M models presented in the Fifth Assessment Report of the Intergovernmental Panel on Climate Change - IPCC. We used the SMAP rainfall-runoff model to obtain future flow projections for the RCP4.5 and RCP8.5 scenarios. As a result, we observed a trend toward water loss and intensification of extreme events, with an increase in variability in both scenarios. We also noted that these climate models have difficulty reproducing the natural variability of southern basins, as the simplification of atmospheric phenomena parameterization prevents them from correctly projecting the precipitation.

: Poultry products in Zambia form an integral part of the human diet in many households, as they are cheap and easy to produce. The burden of poultry diseases has, however, remained a major challenge. Growing consumer demand for poultry products in Zambia has resulted in non-prudent antimicrobial use on farms, intending to prevent and treat poultry diseases for growth optimization and maximising profits. This cross-sectional study aimed to identify the different types of bacteria causing diseases in chickens in Lusaka and to detect the extended-spectrum-lactamase (ESBL)-encoding genes. We collected 215 samples from 91 diseased chickens at three post-mortem facilities and screened them for gram-negative bacteria. Of these samples, 103 tested positive for various clinically relevant Enterobacteriaceae, including Enterobacter (43/103, 41.7%), Escherichia coli (20/103, 19.4%), Salmonella (10/103, 9.7%), and Shigella (8/103, 7.8%). Other isolated bacteria included Yersinia, Morganella, Proteus, and Klebsiella, which accounted for 21.4%. E. coli, Enterobacter, Salmonella, and Shigella were subjected to antimicrobial susceptibility testing. The results revealed that E. coli, Enterobacter, and shigella were highly resistant to tetracycline, ampicillin, amoxicillin, and trimethoprim-sulfamethoxazole, while Salmonella showed complete susceptibility to all antibiotics. The observed resistance patterns correlated with antimicrobial usage estimated from sales data from a large-scale wholesale and retail company. Six (6/14, 42.9%) E. coli isolates tested positive for bla_CTX-M, whilst eight (8/14, 57.1%) Enterobacter samples tested positive for bla_TEM. Interestingly, four (4/6, 66.7%) of the E. coli isolates carrying bla_CTX-M-positive strains were also positive for bla_TEM. Sanger sequencing of the PCR products revealed that five (5/6,83.3%) of the abovementioned isolates possessed the bla_CTX-M-15 allele. The results suggest the presence of potentially pathogenic ESBL-producing Enterobacteriaceae in poultry, threatening public health. Keywords:. Enterobacteriaceae, bla_CTX-M, bla_TEM

Li₂TiO₃ nanopowders were synthesized by hydrothermal process using anatase TiO₂ and LiOH H₂O as raw materials. Li₂TiO₃ crystallizes in the layered monoclinic structure (space group C2/c) with average crystallite size of 34 nm. Morphology, elemental composition and local structure of products were carried out using HRTEM, FESEM, EDS, Raman and FTIR spectroscopy. Transport properties investigated by d.c. (4-probe measurements) and a.c. (complex impedance spectroscopy) show the activation energy of 0.71 and 0.65 eV, respectively. The ionic transport properties of Li⁺ ions in nanocrystalline Li₂TiO₃ characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) validate the good electrochemical properties of this anode material for lithium-ion batteries.

Vanadium(IV) chalcogenide materials are of increasing interest for use in catalysis and energy conversion-related applications. Since no ternary compounds are yet known in the V–Se–Te system, we studied ternary VwSeyTe2–y (w = 1.10, 1.13; y = 0.42, 0.72) phases crystallizing in space group P3m1 (no. 164). Two single-crystal specimens with differing compositions of a solid solution were obtained using the ceramic method. All products were characterized by either single-crystal or powder X-ray diffraction. The lattice parameters increase with rising tellurium content in accordance to the larger ionic radius of the tellurium anion compared to selenium. The chemical compositions were confirmed by energy dispersive X-ray spectroscopy. Further, magnetic measurements revealed mostly antiferromagnetic properties. Simultaneous differential scanning calorimetry/thermogravimetric analyses in nitrogen atmosphere showed endothermic decomposition accompanied by the formation of VN. The results of this work can serve as a basis for the synthesis of new phases in the V–Se–Te and related vanadium chalcogenide systems.

Hypervirulent Klebsiella pneumoniae (hvKp) is a variant that has been increasingly linked to severe, life threatening infections including pyogenic liver abscess and bloodstream infections. HvKp belonging to the capsular serotypes K1 and K2 have been reported worldwide, however very scarce studies are available on the their genomics and virulence. In the current study we report four hypermucoviscous hvKp ESBL clinical strains of capsular serotype K1 and K2 isolated from pus and urine of critically ill patients in tertiary care hospitals in Oman. These strains belong to diverse sequence types (STs) namely ST-23(K1), ST-231(K2), ST-881(K2), and ST-14(K2). To study their virulence, Galleria Mellonella model and resistance to human serum killing were used. The G. mellonella model revealed that the K1/ST-23 isolate is the most virulent as 50% of the larvae died in the first day, followed by isolate K2/ST-231 for which 75% of the larvae died in the second day and isolate K2/ST-14 for which 50% of the larvae died in the second day. Resistance to human serum killing showed there was complete inhibition of bacterial growth of all four isolates by the end of the first hour and up to the third hour. For ST-23(K1), ST-231(K2), ST-881(K2), and ST-14(K2), there was a gradual decrease in the number of colonies up to the second to third hour, which indicates neutralization of bacterial cells by the serum components. However, this was followed by sudden increase of bacterial growth, indicating possible resistance of bacteria against human serum bactericidal activity. Whole genome sequencing (WGS) revealed that hvKp strains display unique genetic arrangement of k-loci. Whole genome SNP-based phylogenetic analysis revealed that these hvKp isolates are phylogenetically distinct, belonging to diverse clades and belong to different STs in comparison to global isolates. This is the first report from Oman detailing the WGS of hvKp clinical isolates and assessing their resistance and virulence genomics, which reinforce our understanding of their epidemiology and dissemination in clinical settings.

New ideas on the framework of Neutrosophic SuperHyperGraph for different styles of Neutrosophic SuperHyper-Wheel and Neutrosophic SuperHyper-Star are introduced. More instances and more clarifications alongside sufficient references are featured with a specific type of independency of SuperHyperVertices.

"Chemical absorption is currently the most advanced technique for capturing carbon dioxide after combustion. A fascinating approach within amine-based technology for post-combustion carbon removal is the utilization of aqueous ammonia as a solvent, leading to a method called chilled ammonia capture. This study aims to enhance the performance of chilled ammonia capture through a thermodynamic assessment, focusing on crystalline configuration.""This study explores the development of an improved second generation chilled ammonia capture process, which involves the formation of solids to enhance capturing efficiency. The simulation software ASPEN is employed to model the expanded UNIQUAC Thermodynamics hypothesis. The modeling encompasses both the conventional carbon ammonia capture process and the more advanced carbon ammonia capture system powered by a crystallizerIn this study, the energy costs associated with implementing different technologies for carbon ammonia capture in typical ultra supercritical power plants are evaluated. The introduction of solid formation in the carbon ammonia capture system has yielded promising results. The findings indicate that the energy required for the carbon ammonia capture system, which utilizes a crystallizer, is approximately 10% lower compared to the overall cost associated with the conventional carbon ammonia capture system. These results highlight the potential for significant energy savings and improved efficiency in carbon capture processes

This study aims to assess trends and significant changes in precipitation and river flow in the Senegal River basin and its upper basin over the period 1982-2021. Eight hydroclimate indicators, namely maximum river discharge (QMAX), standardized flow index, mean daily rainfall intensity index (SDII), maximum 5-day consecutive precipitation (RX5DAY), annual precipitation exceeding the 95th percentile (R95p), annual precipitation exceeding the 99th percentile (R99P), annual flows exceeding the 95th percentile (Q95p), and annual flows exceeding the 99th percentile (Q95p) were considered.. The modified Mann-Kendall test (MMK) was used to analyze trends in extremes while standard normal homogeneity and Pettit’s tests were employed to detect potential breakpoints in these trends. The results indicated an irregular precipitation pattern, with high values of extreme precipitation indices (R95p, R99p, SDII, and RX5DAY) in the southern part, while the northern part exhibits lower values. Inter-annual analysis revealed a significant increase in extreme precipitation events between 1982 and 2021, with a notable breakpoint around the years 2006 and 2007. This breakpoint marks a transition to a much wetter period starting from 2008. Regarding extreme flows, a significant increase was observed between 1982 and 2021. This study provides insights into past hydrological extremes in the study area and can serve as a basis for future research in this field.

Decarbonization of air mobility requires the decarbonization of its energy. While biofuels will play an important role, other low carbon energy carriers based on electricity are considered: battery electrification, liquid hydrogen (LH₂) or eFuel, a hydrogen-based energy carrier. Each energy carrier has its own conversion steps and losses and its own integration effects with the aircraft. These combinations lead to different energy requirements and must be understood to compare their cost and CO₂ emissions. Since they are all electricity-based, this study compares these energy carriers using the well to rotor methodology when applied to a standard Vertical Take-Off and Landing (VTOL) air mobility mission. This novel approach allows one to understand that the choice of the energy carrier dictates the propulsive system architecture, leading to integration effects with the aircraft which can significantly change the energy required, from 400 to 2665 kWh for the same mission. These deviations lead significant differences in CO₂ emissions and costs. Battery electrification is impacted by the battery manufacturing but has the lowest electricity consumption. It is an optimum solution but only until the battery weight can be lifted. In all scenarios eFuel is more efficient than LH₂. We conclude that carrying the most efficient molecule in an aircraft pays the extra energy cost spent on the ground. Finally, we found that for each of these energy carriers, it is the electricity carbon intensity and price which will dictate the cost and CO₂ emissions of an air mobility mission.

With the development of modern industry, the issue of water pollution has garnered increasing attention. Photocatalysis, as a novel green environmental technology that is resource-efficient, environmentally friendly, and highly promising, has found extensive applications in the field of organic pollutant treatment. However, common semiconductor materials exhibit relatively low photocatalytic efficiency in the visible light range or inefficient separation of photogenerated charges, resulting in their limited ability to harness solar energy effectively. Consequently, the development of new photocatalysts has become a pivotal focus in current photocatalysis research to enhance solar energy utilization. This revision provides a brief explanation of the photocatalytic mechanism of the AgIO3/CTF heterojunction photocatalyst. Due to the Localized surface plasmon resonance (LSPR) effect, Ag nanoparticles demonstrate significant absorption in the visible light region, playing a crucial role in the highly efficient photocatalytic reduction of organic pollutants.

Satellite remote sensing is a powerful tool to map flooded areas. In the last years, the availability of free satellite data sensibly increased in terms of type and frequency, allowing producing flood maps at low cost around the World. In this work, we propose a semi-automatic method for flood mapping, based only on free satellite images and open-source software. As case studies, we selected three flood events recently occurred in Spain and Italy. Multispectral satellite data acquired by MODIS, Proba-V, Landsat, Sentinel-2 and SAR data collected by Sentinel-1 were used to detect flooded areas using different methodologies (e.g., MNDWI; SAR backscattering variation; Supervised classification). Then, we improved and manually refined the automatic mapping using free ancillary data like DEM based water depth model and available ground truth data. For the areas affected by major floods, we also validated and compared the produced flood maps with official maps made by river authorities. We calculated flood detection performance (flood ratio) for the different datasets we used. The results show that it is necessary to take into account different factors for the choice of best satellite data, among these, the time of satellite pass with respect to the flood peak is the most important one. SAR data showed good results only for co-flood acquisitions, whereas multispectral images allowed detecting flooded areas also with the post-flood acquisition. With the support of ancillary data, it was possible to produce reliable geomorphological based flood maps in the study areas.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

It is common knowledge that increasing CO₂ concentration plays a major role in enhancement of the greenhouse effect and contributes to global warming. The purpose of this study is to complement the conventional and established theory that increased CO₂ concentration due to human emissions causes an increase of temperature, by considering the reverse causality. Since increased temperature causes an increase in CO₂ concentration, the relationship of atmospheric CO₂ and temperature may qualify as belonging to the category of “hen-or-egg” problems, where it is not always clear which of two interrelated events is the cause and which the effect. We examine the relationship of global temperature and atmospheric carbon dioxide concentration at the monthly time step, covering the time interval 1980–2019, in which reliable instrumental measurements are available. While both causality directions exist, the results of our study support the hypothesis that the dominant direction is T → CO₂. Changes in CO₂ follow changes in T by about six months on a monthly scale, or about one year on an annual scale. We attempt to interpret this mechanism by involving biochemical reactions, as at higher temperatures soil respiration, and hence CO₂ emission, are increasing.

Natural Gas (NG) processing is a prominent industrial separation process. Among the available techniques, the innovative membrane process shows potential for efficient removal of impurities, including carbon dioxide (CO₂). This study focuses on utilizing breakthroughs in membrane separation to drive sustainable CO₂ extraction from natural gas. Through comprehensive research and analysis, we explore the effectiveness and feasibility of membrane-based systems in removing CO₂ impurities from NG, thus promoting greener and more sustainable industrial practices. Our findings underscore the transformative nature of membrane separation technology, presenting new possibilities for a more environmentally-friendly and sustainable approach to CO₂ extraction from natural gas.Natural Gas (NG) processing utilizes various techniques for impurity removal, with the membrane process emerging as a promising option for efficient carbon dioxide (CO₂) extraction. This research proposes the integration of a simple mathematical model into ASPEN HYSYS to design a membrane system for CO₂/CH₄ separation. The study also investigates parameter sensitivities by altering operating conditions, such as feed composition and pressure, as well as membrane properties, including selectivity. By analyzing these variables, we aim to optimize the performance and efficiency of the membrane system, facilitating the sustainable extraction of CO₂ from NG. The findings contribute to advancing the design and operation of membrane-based processes for CO₂ separation, paving the way for greener and more sustainable industrial practices. In addition, this study explores various configurations for optimizing the design of the membrane system, including single-stage with and without recycling as well as double-stage configurations. The investigation demonstrates that methane recovery can be enhanced through the recycling of the permeate stream and by implementing a double stage membrane system. These findings highlight the potential for improving the efficiency and performance of the membrane system, enabling higher methane recovery rates. By considering different configurations, this research contributes to the development of more effective and sustainable CO₂ extraction processes from natural gas.

Nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC ) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases, and a crystallite size of approximately 21 nm; while AC had XRD peaks of graphite and carbon, and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2×10^-3 min^-1 and an MB removal efficiency of 96.6% after 30 min treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e^-/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite in this study can be used for treating industrial or household wastewater with organic pollutants.

Nowadays, it is highly desired to develop highly active and humidity resistive ozone decomposition catalyst to eliminate the ozone contaminant, one of the primary pollutants in air. In this work, a series of Cu2S hollow structured materials are rapidly synthesized using different structured Cu2O templates. The Cu2S from porous Cu2O shows the highest ozone catalytic decomposition efficiency of >95% to 400 ppm ozone with a weight hourly space velocity of 480,000 cm3g-1h-1 in dry air. Importantly, the conversion still keeps >85% in a high relative humidity of 90%. The mechanism is explored by diffusive reflectance infrared spectroscopy which shows the decomposition intermediate of O22-, and the X-ray photoelectron spectroscopy reveals the dual active site of both Cu and S. All these results show the effective decomposition of ozone by Cu2S especially in harsh environments, promising for active ozone elimination.

The thermoelectric generator (TEG) has much potential as a renewable energy technology that could be used in ocean thermal energy conversion (OTEC). This technique employs TEGs and heat exchangers as substitutes for the intricate elements found in conventional OTEC systems, including pressure valves, evaporators, condensers, and turbine generators. By harnessing the temperature difference between warm surface seawater and cold deep seawater, it facilitates the conversion of this thermal gradient into electrical energy. This study used computer simulations to look at and compare three different types of heat exchangers: a cavity-type heat exchanger, a heat exchanger with flat fins, and a heat exchanger with longitudinal vortex generators (LVGs). The objective was to evaluate the influence of these designs on the thermoelectric conversion performance when implemented in OTEC systems. The study's findings indicate that using heat exchanger configurations featuring flat fins, or LVGs, enhances the efficiency of thermal energy transfer from warm seawater to TEGs, resulting in a notable enhancement in the output power of TEGs. Furthermore, the efficiency of TEG thermoelectric conversion is influenced by varying seawater flow rates in relation to the performance of flat fins and LVGs. In contrast to the cavity-type heat exchanger, the utilization of a heat exchanger equipped with flat fins has been found to yield a notable enhancement in the output power of TEGs by approximately 22.92%. Furthermore, this configuration demonstrates a substantial improvement in thermoelectric conversion efficiency, exhibiting an increase of around 40.01%. These improvements are observed under certain conditions pertaining to flow rates and fin heights. Utilizing heat exchangers equipped with LVGs has been found to enhance the output power of TEGs by 13.02% and improve the overall thermoelectric conversion efficiency by 17.72%. These improvements are observed under certain conditions, including specific flow rates, LVG tilt angles, and locations.

Our understanding of pull-apart basins and their fault systems has been enhanced by analog experiments and simulations. However, there has been no opportunity to compare the faults that constitute pull-apart basins with surface ruptures during earthquakes. In this study, we investigated the effects of a 2018 earthquake (Mw 7.5) on a pull-apart basin in the Palu-Koro fault system, Sulawesi Island, Indonesia, using geomorphic observations in digital elevation models, optical correlation with pre- and post-earthquake satellite images. A comparison of active fault traces determined by geomorphology with the locations of surface ruptures from the 2018 earthquake shows that some of the boundary faults of the basin are inactive and that active faulting has shifted to basin-shortcut faults and relay ramps. We also report evidence of lateral spreading, in which alluvial fan materials moved around the end of the alluvial fan. These phenomena may provide insights for anticipating the location of future surface ruptures in pull-apart basins.

Despite the overall extension of the Amazon basin (approximately 6,000,000),which encompasses such a complex ecosystem and territories belonging to seven different nations, it is worth mentioning that environmental assessment related to changes in land use and land cover (LULC) in this region are often conducted respecting geopolitical boundaries associated with each country or taking into account the so-called Amazon biome. With the purpose of prospecting the intricate and hidden hydrological patterns, we undertake an in-depth evaluation of the water balance along the 2001-2021 time span across the whole basin, whose behavior depends on the features deriving from the metamorphoses in land use and land cover. To accomplish that task, the influence of the components of the water balance, namely rainfall and evapotranspiration, jointly with the terrestrial topographic mapping, are examined to investigate the interactions among the physical mechanisms that make up the hydrological cycle and the corresponding physical hydrological processes triggered by deforestation and reforestation in the region. More specifically, the modeling approach was rigorously designed to also consider, separately or not Negro, Solimões, Madeira, Tapajós and Xingu hydrographic sub-basins, which are the most important ones of the Amazon basin. The results highlight that, in the southern region of the Amazon, specifically within the Madeira river sub-basin, the lowest forest coverage is observed (56.0%), whereas in the northern Negro river sub-basin, the most notable forest coverage is observed (85.0%).The most preserved forest areas, such as the Negro and Solimões river sub-basins, with percentages of 81.9% and 74.2%, respectively, have higher annual rates of precipitation and evapotranspiration over time. On the other hand, regions that suffered the most intense deforestation along the time period studied, such as the Madeira, Tapajós and Xingu sub-basins, have lower annual rates of precipitation and evapotranspiration, with a preservation percentage of 54.6%, 62.6% and 70, 7%, respectively. As the pace of deforestation slowed between 2003 and 2013, annual precipitation rates increased by 12.0%, while evapotranspiration decreased by 2.0%. The hydrological findings of this paper highlight th predominant role of the forest in the context of the global water balance of the Amazon basin and the potential to also produce distinct impacts within different parts of the basin in terms of having more or less rainfall and evaporation. In addition, those variabilities in the hydrological operational components and mechanisms due to changes in land cover and land use also reveals the potential impacts that could be expected in the surrounding areas, closer or farther, notably beyond the limits of the Amazon basin.

Adherence is vital for medicine to have an effect, yet adherence is considered to be low. However, research into adherence tends to focus on quantitative analysis of performance, something which fails to perceive how people are adherent in their many different environments. As a contribution to gaining a deeper understanding, interviews were held with 30 individuals in UK, Egypt, Kazakhstan and 6 countries in sub-Saharan Africa to understand their perceptions on adherence for a range of drugs, and these were compared with an existing well-regarded list. New reasons for non-adherence were discovered, and a new viewpoint on adherence derived which considers adherence to be a single act and therefore as an individual opportunity to be adherent, permitting greater focus on the enablers and inhibitors of adherence at a point in time.

This article describes the challenges, pharmacological strategies, and recommendations for managing multidrug-resistant breast cancer in Sub-Saharan Africa (SSA). By examining the current breast cancer treatment landscape, region-specific challenges, and promising pharmacological interventions, the objective is to bring to light the insufficient research on breast cancer and its multidrug resistance in this part of the world and guide healthcare professionals, policymakers, and researchers in developing evidence-based strategies for improved breast cancer care in SSA. Breast cancer is the leading cause of cancer morbidity in SSA, necessitating continuous advancements in its management. This overview explores the evolution of breast cancer treatment, including surgery, targeted therapy, immunotherapy, radiotherapy, and chemotherapy. Despite these advancements, multidrug resistance poses a significant challenge, impacting treatment efficacy and patient outcomes.The article provides insights into various breast cancer treatment modalities, emphasizing surgery, targeted therapy, immunotherapy, radiotherapy, and chemotherapy. Each approach is discussed in detail, highlighting its significance in managing breast cancer. The effectiveness of these treatments is contingent on timely diagnosis and intervention. Multidrug resistance is examined as a critical obstacle in breast cancer treatment, elucidating its impact on treatment failure and patient outcomes. Mechanisms such as the efflux system, enhanced DNA repair, apoptosis inhibition, alterations in drug targets, and the tumor microenvironment contribute to multidrug resistance, emphasizing the need for a multifaceted understanding.The unique challenges faced in SSA regarding multidrug-resistant breast cancer are delineated. These include the lack of comprehensive data, late presentation and diagnosis, poor genomic studies, limited access to specialized care, financial constraints, inadequate infrastructure, and psychosocial support issues. Addressing these challenges is crucial for devising effective strategies. In response to multidrug resistance, the article discusses contemporary treatment strategies such as P-glycoprotein inhibitors, combined chemotherapy, and immunotherapy. Notable advancements, including the use of Tariquidar and synergistic effects of combined chemotherapy, are highlighted, presenting promising avenues for overcoming resistance.The article proposes recommendations to enhance breast cancer management in SSA, encompassing strengthening primary healthcare services, creating specialized oncology facilities and long-term monitoring and data collection. Breast cancer management in SSA is multifaceted, marked by challenges and evolving solutions. Multidrug resistance remains a significant hurdle, demanding a holistic approach. Promising advancements in pharmacological interventions offer hope, while comprehensive recommendations serve as a roadmap for progress. By implementing these strategies, SSA can substantially improve multidrug-resistant breast cancer care and overall patient well-being.

Sinkhole flooding is an essential hydrological process to recharge karst aquifer in arid to dry sub-humid regions. On the other hand, the increase of rain extremes is one of the major consequences of the global warming, together with the expansion of drylands. Thus, appropriate runoff regulation in endorheic karst basins in order to reduce the risk of flooding and improve the quantity and quality of the water drained by sinkholes will be more and more crucial. With these premises, a systematic review was performed by using WoS engine to infer the best practices for the karst water management in regions actually or potentially affected by water scarcity. Hydrological models are essential to manage the consequences of climate change on karst water resource, however the review shows that providing the tools necessary for reliable modeling is still challenging. Finally, due to the intrinsic vulnerability of the karst aquifers, pollution reduction and wastewater recycling policy will play key role in the next decades.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

A comprehensive investigation was undertaken at Vytautas Magnus University Experimental Station, located at 54°52’50” N latitude and 23°49’41” E longitude on soil (Epieutric Endocalcaric Planosol – PLe-gln-w) since 1999, to understand the impacts of different agrotechnical measures on soil health and crop yield. Two primary factors were assessed. Factor A incorporated practices of straw removal versus straw chopping and spreading, while Factor B evaluated a spectrum of tillage techniques: conventional deep ploughing, shallow ploughing, ploughless tillage, single seedbed discing, and two no-tillage practices, one of which involved cover crops. Findings from this long-term study highlight the significant potential of specific farming systems in enhancing soil organic carbon. It has a positive effect on the release of CO2 emissions from the soil, thus promoting soil resilience and increasing plant productivity. These insights are paramount in devising sustainable agricultural strategies to counter the challenges of climate change on agroecosystems. This research showcases the profound effects of combining residue management and tillage practices, setting a novel standard for sustainable soil management of climatic uncertainties.

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.

Based on the plate tectonic theory, using seismic, geology, and public literature data, the proto-type basins and lithofacies paleogeography during the main geological periods of the passive continental margin of East Africa are restored, and the architecture characteristics of the basins and the differences in sedimentary fillings are analyzed. Combined with the dissection of discovered oil and gas reservoirs, four types of hydrocarbon accumulation models are established, the favorable hydrocarbon accumulation combinations (plays), and the next exploration directions in this region are explored. The passive continental margin basins in East Africa experienced three proto-type stages: intracontinental aborted rift during the Late Carboniferous-Triassic Karoo period, intracontinental-intercontinental rift during the Jurassic period, and passive continental margin basin since the Cretaceous period. Affected by the difference in sedimentary filling thickness between the rift period and depression period, four types of passive continental margin basins are formed: rifted type, depressed type, faulted depression type, and reformed delta type. The maximum sedimentary thickness of the rifted basins during the rift period is greater than 3500 m, and that during the depression period is less than 4000 m, forming a "single-source structure type" hydrocarbon accumulation model. The exploration of rifted basins should focus on giant structural traps at the top of the rifted sequences. The maximum sedimentary thickness of the depressed basins during the depression period exceeds 4000 m, forming a "single-source fan group type" hydrocarbon accumulation model. The dominant exploration directions of depressed basins are sedimentary sand bodies and structural-lithologic traps during the depression and drift periods. The maximum sedimentary thickness of the faulted depression basins during the rift period is greater than 3500 m, and that during the depression period is greater than 4000 m, forming a "double-source and double-combination type" hydrocarbon accumulation model. The exploration of rifted basins should focus on giant slip-collapse-debris flow sedimentary sand bodies on the upper and middle slopes. In addition to the large sedimentary thickness of the early rift and the central depression, the delta thickness of the reformed delta basins during the late depression period since the Miocene is more than 4000 m, and four structural belts (growth fault, mud diapir, thrust fold, and foredeep gentle slope) were formed from onshore to offshore, forming a "three-source and multi-combination type" hydrocarbon accumulation model. All four structural belts can form giant oil and gas fields.

The Pannonian basin major heat system in Central Europe. Their peripheral basins like the East Slovakian basin is a example of a geothermal structure with a linear directed heat flow ranging from 90 to 100 mW /m2 from west to east. However, the use of the geothermal source is limited by several critical tectono-geologic factors: (a) tectonics, and the associated disintegration of the aquifer block by multiple deformations during the pre-Paleogene mainly Miocene period. The main discontinuities of NW-SE and N-S direction negatively affect the permeability of the environment. On the contrary, for utilization are important the secondary minor NE-SW dilatation open fractures which have developed by sinistral transtension on N–S faults and accelerated normal movements to the southeast in the present. (b) hydrogeological conditions, the geothermal structure accommodated three water types, namely Na-HCO3 with 10.9 g.l-1 mineralization (in the north), the Ca-Mg-HCO3 with 0.5 – 4.5 g.l-1 mineralization (in the west), and Na-Cl water type containing 26.8-33.4 g.l-1 (in the southwest) mineralization. The chemical composition is influenced by the Middle Triassic dolomites aquifer as well as by infiltration of saline solutions and meteoric waters along open fractures/faults. (c) geothermally anomalous heat 123 – 129 °C close to volcanic chain with 170 l/s total flow seems to be the perspective for heat production.

This study investigates the influence of economic growth on CO2 emissions levels in three developed countries—Argentina, Equatorial Guinea, and South Korea—based on their status as high-income countries. We test the environmental Kuznets curve (EKC) hypothesis using the time series approaches to check the relationship and direction of causality among the variables over a sample spanning 1974–2020. The results show an inverted U-shaped short-run relationship in all three countries. In the long run, only South Korea supports the EKC hypothesis. Further, Granger causality results indicate the existence of causality. These long-run causal relationships between economic growth and emissions recommend one policy implication that wealthy governments must expand investments in renewable clean energy projects and R&D, with regulatory measures to suppress harmful environmental procedures and support environmentally friendly development.

The removal of H2S from natural gas and other gases such as biogas, refinery gases, and coal gas is required because H2S is toxic and corrosive, even in traces. Zeolites are widely used in the removal of H2S from the above-mentioned gases. In this work, we prepared an Ag-exchanged 13X molecular sieve by using different concentrations of AgNO3 to increase its adsorption properties. XRD, SEM, and BET techniques were used to characterize samples. When compared to unmodified 13X, the adsorption capacity of AgII-13X increased by about 50 times. The results of this study suggest that the silver-modified 13X molecular sieve is highly effective at extracting H2S from natural gas.

Cesium lead iodide (CsPbI3) perovskite nanocrystals (NCs) are a promising material for red light-emitting diodes (LEDs) due to their excellent color-purity and high luminous efficiency. However, small-sized CsPbI3 colloidal NCs, such as nanocubes, used in LEDs suffer from confinement effects, negatively impacting their photoluminescence quantum yield (PLQY) and overall efficiency. Here, we introduced YCl3 into the CsPbI3 perovskite, which formed anisotropic, one-dimensional (1D) nanorods. This was achieved by taking advantage of the difference in bond energies between Cl− and I− ions, which caused YCl3 to promote the anisotropic growth of CsPbI3 NCs. The YCl3-based nanorods improved the PLQY and storage stability by passivating the defects reducing the nonradiative recombination rates. When the YCl3-substituted CsPbI3 nanorods are applied to the emissive layer in LEDs, we achieve an external quantum efficiency of ~3.16% which is 1.86-fold higher than the pristine CsPbI3 NCs (1.69%) based LED. Notably, the ratio of horizontal transition dipole moments (TDMs) in the anisotropic YCl3:CsPbI3 nanorods was determined to be 75%, which is higher than the isotropically oriented TDMs in CsPbI3 nanocrystals (67%). This increased TDM ratio led to higher light outcoupling efficiency in nanorods-based LEDs. Overall, the results suggest that YCl3-substituted CsPbI3 nanorods could be promising for achieving high-performance perovskite LEDs.

The population growth and its needs, has increasingly demanded water resources, requiring managers to adopt mechanisms to guarantee the availability and quality of water from springs. Among the instruments defined by law n. 9433/1997, water charges stand out. In this sense, the objective was to evaluate the evolution of charging for the use of water resources in Brazil, with emphasis on the channel of the Hydrographic Basin of the Paranaíba River. The methodology used was based on two phases, one of reviewing the articles available in Capes journals and the other, consulting the spreadsheets of the Araguari River Basin Agency with information on charges for the use of water within the competence of the Union in the Hydrographic Basin of the Paranaiba River. The results showed that charging for the use of water resources establish a relevant instrument for disciplining and raising financial resources that will enable improvements in the planning and management of water use. It should be noted that irrigation emerges as the main user of the flow captured from the Paranaíba River. However, the main source of funds for charging comes from the public supply. Among the Federation Units, the Federal District proved to be the largest source of contributions for charging the use of the Union's water resources in the Paranaíba River Basin.

In the last years, new numerical methods have been applied to weather data for water budget es-timation. Geostatistics is one of the most powerful approaches, when it comes to studying spatially relevant natural phenomena, as it takes into account the spatial correlation among measurements over a specific study area and increases the reliability of the estimation by providing the associate uncertainty. In this study, we tested the feasibility of using a geostatistical method called Ordinary Kriging to provide a reliable estimation of the water budget of the Foro river basin (Periadriatic area, Central Italy), by comparing the obtained results with a more traditional yet robust approach based on the Thiessen polygon spatialization method, considered here as a reference. The spatial estimation with the selected geostatistical and traditional approaches was performed on the av-erage monthly rainfall and temperatures derived from 33-year-long time series measured at the weather station of the regional monitoring network. To transform the spatial variables quantities of both rainfall and air temperature into actual runoff estimates that ideally represent the river dis-charge, we used both the Turc and Thornthwaite methods, considering variable Potential Infiltra-tion Coefficients according to the hydrogeological complexes’ distribution. For the geostatistical method, the same procedure was applied to the 95% confidence interval limits, to quantitatively assess the possible impact of the spatial uncertainty on the estimation of the river discharge. The results obtained by both methods, subsequently converted into monthly discharges, were com-pared to the average monthly discharges related to 33-year-long time series measured at different locations along the Foro river. The results obtained with the geostatistical approach proved to be in line with the ones from the traditional method. Additionally, using the rainfall and temperature values obtained with the Ordinary Kriging and the corresponding confidence interval limits, it was possible to quantify the uncertainty associated with the discharge values, making the estimates more reliable than the ones obtained with the traditional approach. However, the yearly distribu-tion of river discharge obtained by both the geostatistical and traditional methods appeared to be dissimilar to the measured ones. In such anthropized and groundwater-dependent river basins, the surface water use as well as the regulatory effect of the alluvial aquifer regime may affect the river discharge variability over the year and then can account for similar discrepancies between the in-flow and outflow water volumes.

This paper examines the diurnal cycle of convection (DCC) over Lake Titicaca Basin (LTb) during summertime months based on the high spatial resolution (8 x 8 km2) and hourly temporal resolution, estimates of Climate Prediction Center Morphing technique (CMORPH). Analysis was performed using observed data from rain gauges (Rg-SENAMHI) for the period 2002 to 2013. Graphical comparisons and several statistical metrics such as correlation coefficient, bias, and root mean square error were used to evaluate CMORPH product. Spatial maps and graphic metrics of diurnal cycle were developed to assess CMORPH data, spatial dependency an accuracy over the LTb. Approximately, 43% of the total Rg-SENAMHI variation is explained CMORPH data. The correlation between Rg-SENAMHI and CMORPH is positively over southeast and northern LTb, and negatively in the central and southern LTb. A underestimation bias is observed over most the LTb areas and overestimation bias (e.g., Lagunillas, Isla Suana and Desaguadero stations). In general, spatial patterns of rainfall over the LTb were captured through CMORPH data. Over the surrounding lake area, high mountain, and plateau area, maximum peaks of precipitation occur in the early evening, neverhtheless over low areas such as the lake, surrounding and valleys, maximum precipitation values occur early morning. The results show that DCC its very related by surface exchange processes and local circulation resulting from solar radiation and heterogeneous topography.

This study introduces a novel nanocomposite coating composed of PANI/CeO2 nanocomposite films, aimed at addressing corrosion protection needs. Analysis through FTIR spectra and XRD patterns confirms the successful formation of the nanocomposite films. Notably, the PANI/CeO2 nanocomposite films exhibit a hydrophilic nature. The bandgap energy of the PANI composite film measures at 3.74 eV, while the introduction of CeO2 NPs into the PANI matrix reduces the bandgap energy to 3.67 eV. Furthermore, the electrical conductivity of the PANI composite film is observed to be 0.40 S.cm-1, with the incorporation of CeO2 NPs leading to an increase in electrical conductivity to 1.07 S.cm-1. To evaluate its efficacy, electrochemical measurements were conducted to assess the corrosion protection performance. Results indicate a high protection efficiency of 92.25% for the PANI/CeO2 nanocomposite film.

This contribution deals with the assessment of air pollution caused by atmospheric aerosol particulate matter fraction PM10 and benzo[a]pyrene (BaP) in the urban agglomeration of Ostrava, located in the Czech Republic in Central Europe. The motivation for this research was the need to identify the sources of air pollution in the area, particularly in locations where the contribution of different sources to concentrations of pollutants of concern has not been elucidated yet. In this study, source apportionment in the vicinity of the industrial hot-spot was performed by statistically evaluating measured pollutant concentrations as a function of meteorological variables and using the Positive Matrix Factorization (PMF) receptor model. A significant methodological innovation and improvement over previous assessments was the higher monitoring resolution of benzo[a]pyrene, with samples collected at three-hour intervals instead of the standard 24-hour collection period. The key findings indicate that in the cold part of the year, secondary particles - specifically sulphates and ammonium nitrates - were responsible for the most significant portion of PM10 air pollution throughout the area of interest. The contribution of these particles ranged from one third to two fifths of the total concentration, except at the industrial site of Ostrava-Radvanice (TORE), where they accounted for approximately one fifth of the measured pollution concentration level. Emissions from individual household heating were identified as the main source of this type of pollution. With regards to benzo[a]pyrene air pollution, the study found that in the whole area of interest, except for the Ostrava-Radvanice site, it mainly originated from individual heating with coal (90%). In contrast, at the Ostrava-Radvanice site, two-thirds of the benzo[a]pyrene pollution came from the premises of Liberty Ostrava a.s., primarily from coke production, and less than one-third from local domestic heating. This study also determined the spatial extent of the occurrence of extremely high benzo[a]pyrene concentrations (above 5 ng/m3), which are estimated to affect nearly 10,000 inhabitants. The results confirm that the data from the TORE station are only representative of its immediate surroundings and are not applicable to the assessment of air quality and causes of air pollution in the whole city of Ostrava or the urban area of Ostrava-Radvanice as a whole. After years of research, these findings provide the Ministry of the Environment of the Czech Republic and the government with an accurate basis for implementing measures to address the identified pollution sources in the area of interest. The success of this study was made possible by the adoption of a more detailed sampling approach, which involved a resolution of 3 hours instead of 24 hours. This methodological improvement is a significant finding and will be useful for future source apportionment studies.

Mangrove forests store and sequester large area-specific quantities of blue carbon (C_org). Except for tundra and peatlands, mangroves store more C_org per unit area than any other ecosystem. Mean mangrove C_org stock is 738.9 Mg C_org ha⁻¹ and mean global stock is 6.17 Pg C_org, which equates to only 0.4–7% of terrestrial ecosystem C_org stocks but 17% of total tropical marine C_org stocks. Seagrasses sequester more C_org per unit area than mangroves (179.6 g C_org m⁻²·a⁻¹) but twice the C_org sequestered by mangroves globally (15 Tg C_org a⁻¹). Mangroves sequester only 4% (range 1.3–8%) of C_org sequestered by terrestrial ecosystems, indicating that mangroves are a minor contributor to global C storage and sequestration. CO₂ emissions from mangrove losses equate to 0.036 Pg CO₂-equivalents a⁻¹ based on rates of C sequestration but 0.088 Pg CO₂-equivalents a⁻¹ based on complete destruction for conversion to aquaculture and agriculture. Mangrove CO₂ emissions account for only 0.2% of total global CO₂ emissions but 18% of CO₂ emissions from the tropical coastal ocean. Despite significant data limitations, the role of mangrove ecosystems in climate change mitigation is globally insignificant but may be more significant and effective at the national and regional scale.

In recent years, machine learning (ML) techniques have emerged as an efficient and effective technology within the petroleum industry. This paper focuses on the current application of ML in enhanced oil recovery (EOR) through CO2 injection, which exhibits promising economic and environmental benefits of climate-change mitigation strategy. Our comprehensive review explores the diverse use cases of ML techniques in CO2-EOR, including aspects such as minimum miscible pressure (MMP) prediction, well location optimization, oil production and recovery factor prediction, multi-objective optimization, Pressure-Volume-Temperature (PVT) properties estimation, Water Alternating Gas (WAG) analysis, and CO2-foam EOR, from 101 reviewed papers. In this comprehensive review, we catalog relative information, including the input parameters, objectives, data sources, train/test/validate information, results, evaluation, and rating score for each area based on criteria such as data quality, ML building process, and analysis of results. We also briefly summarized the benefits and limitations of ML methods in petroleum industry applications. Our detailed and extensive study could serve as an invaluable reference for employing ML techniques in the petroleum industry. Based on the review, we found that ML techniques offer great potential in solving problems in the majority of CO2-EOR areas involving prediction and regression. With the generation of massive amounts of data in the everyday oil and gas industry, machine learning techniques can provide efficient and reliable preliminary results for the industry.

Recently, Shehata et al. [37] introduced the r+1Rs(B;C; z) matrix function and established some properties. The aim of this study established to devote and derive certain basic properties including analytic properties, recurrence matrix relations, dierential properties, new integral representations, k- Beta transform, Laplace transform, fractional k-Fourier transform, fractional integral properties, the k-Riemann{Liouville and k-Weyl fractional integral and derivative operators an extended version of r+1Rs;k matrix function. We establish its relationships with other well known special matrix functions which have some particular cases in the context of three parametric Mittag-Leer matrix function, k- Konhauser and k-Laguerre matrix polynomials. Finally, some special cases of the established formulas are also discussed.

Tamarix is native to Eurasia, plus the northern and southern territories of Africa, with some species being introduced into America and Oceania. They are usually found in arid, desertic or subdesertic areas, often on saline or subsaline soils, under Mediterranean, Temperate or Subtropical climates. The genus is renowned by its complex taxonomy, which has usually based on rather variable or unstable characters, which led to contrasting taxonomic treatments. As part of the taxonomic revision of Tamarix undertaken by the authors, nine names (i.e., T. africana, T. bounopoea, T. malenconiana, T. muluyana, T. tenuifolia, T. tingitana, T. trabutii, T. valdesquamigera, and T. weyleri) published from material collected in the southwestern parts of the Mediterranean basin are taxonomically and nomenclaturally discussed after analysing their original and/or type material. Seven intended holotypes are corrected here to lectotypes; one epitype is designated for T. africana to warrant current use of the name; and one isotype, 27 isolectotypes and 11 syntypes are also identified for the studied names. Further, the taxonomic identity of all names and their eventual synonymic placement are accordingly discussed.

Michoacan state has a long history in plant domestication’s. Physalis ixocarpa is a native plant that growth associated to corn crops from this region. Such plants have similar fruits to Physalis philadelphica (husk tomate). Due to the domestication process includes the adaptation to environmental factors, we ask if 1) Does P. ixocarpa has the capacity of association with bacterial communities of the zone where it was domesticated?, and 2) Does the rhizobiome of this plant can increase the potential functions in the soil?. An experiment was established in a traditional milpa system. Samples of rhizobiome from corn, P. ixocarpa, P. philadelphica, and soil were sequenced using Next Generation Sequencing in the region 16S. The potential function, metabolic pathway reconstruction and participation of each bacteria genus was inferred using iVikodak platform. A total of 34 Phyla and 795 genera were identified. Purine metabolism's was the principal function, where all rizhobiomes showed similar metabolic pathways. However, the difference among plant species is the participation of the distinct genera in the purine metabolism. We conclude that rhizobiome of P. ixocarpa shows complementarity for the soil functions, and their utilization can be helpful in zones where the agricultural practices have degraded microbiological soil conditions.

This study evaluates spatial analyses of groundwater quality and environmental changes to obtain information on the groundwater contamination in the Permian Basin, Texas. Coupled with the U.S. government’s open data, these analyses can identify regions where environmental change could have potentially effected groundwater quality. A total of thirty-six wells were selected within the six counties: Andrews, Martin, Ector, Midland, Crane, and Upton. Spatial distribution maps were created for six different parameters: pH, total dissolved solids (TDS), chloride, fluoride, nitrate, and arsenic. Total groundwater quality maps incorporate all the contaminants and denote regions of poor, medium, and optimum conditions. To identify spatial changes in groundwater quality, maps were separated into two different time intervals, 1992-2005 and 2006-2019. We found that groundwater contamination resulted primarily from the mobilization of the contaminant from natural sources or anthropogenic activities such as chemical fertilizers. Overall, groundwater quality decreased during the study period from 1992 to 2019 as population and urban growth began to develop in the Permian Basin. This study contributes on understanding of the response of groundwater quality associated with environmental change in the Permian Basin. Therefore, this research provides important information for groundwater managements in developing plans for the use of water resource in the future for Texas.

This study was designed to assess the reliability of geographic information using satellite image information in ungauged basins. For this, this study constructed geographic information using actual gauged data and satellite information data and conducted runoff analysis through S-RAT, a rainfall–runoff model, and performed the comparison and analysis of geographic information and runoff data. For actual gauged data, the gauged geographic information of the Water Resources Management Information System (WAMIS) was collected, and for satellite information, the image information of moderate-resolution imaging spectroradiometer (MODIS) observation sensor loaded on Terra Satellite was collected. As analysis areas, three basins where mountains occupy more than 80% and another three basins where urban areas occupy more than 7% in the Han River basin were selected. According to the analysis result, the gauged information and satellite image information showed great difference in runoff, maximum 50% in peak flood and maximum 17% in total flood, in the rivers with many urban areas, while the runoff difference in the rivers with many mountains showed maximum 13% in peak flood and 4% in total flood. What showed the greatest difference in image information was land use, and it turned out that the MODIS satellite recognized the urban rivers as cities for more than maximum 60% compared to WAMIS-gauged data. Meanwhile, in the forest area, the MODIS satellite image showed error of less than 5% of the WAMIS-gauged data, which indicates that it has higher applicability in Mountain Rivers.

The study evaluates the toxic effects of acute and sub-acute oral administration of methanol extracts of Geophila obvallata in rats. During acute study, a dose of 1600, 2900 and 5000 mg/kg bw of extract was orally administered to rats. Rats were observed for signs of toxicity for two weeks. During sub-acute study (28 days), the extract, at doses of 100, 500 and 1000 mg/kg bw were administered orally to rats while control rats were given only tap water. At the end of the study, samples were collected for analyses. In acute toxicity studies, the extract did not induce death after single dose administration. Hence, the LD50 was estimated above 5000mg/kg. The results of sub-acute toxicity study show that no significant changes were observed in the body weights, organ weights, kidney function and organ histology. There were significant changes in hematology and biochemical indices investigated at elevated doses of 500 and 1000 mg/kg bw compared to the control. GOE may be considered non-toxic at a dose of 100 mg/kg with promising applications in drug therapy.

Pollution of sub-surface water reservoirs mainly rivers and streams through contaminated water point sources (CWPS) was studied. The objective was to formulate a discrete time delay mathematical model which describes the dynamics of reservoir pollution using mixing-problem processes that involve single species contaminants such as nitrates, phosphorous and detergents. The concentration of pollutants was expressed as a function of the inflow and outflow rates using the principle for the conservation of mass. Systems of ODEs generated from principles of mixing problems were refined into a system of DDEs so that the concentration of pollutant leaving the reservoir at time would be determined at some earlier instant, for the delay. The formulated model is a mathematical discrete time delay model which would be used to describe the dynamics of sub-surface water reservoir pollution. The results from the validation of the model were analyzed to determine how time delays in the mixing processes affect the rate of particle movement in water reservoirs.

In sub-Saharan Africa (SSA), cervical cancer is a critical public health issue; it is the second leading cause of cancer among women and the leading cause of female cancer deaths. Incidence and mortality rates are substantially higher than in high-income countries with population-based screening programs, yet implementing screening programs in SSA has so far proven to be challenging due to financial, logistical and sociocultural factors. Human Papillomavirus (HPV) vaccination is an effective approach for primary prevention of cervical cancer and presents an opportunity to reduce the burden from cervical cancer in SSA. With a number of SSA countries now eligible for GAVI support for vaccine introduction, it is timely to consider the factors that impede and facilitate implementation of vaccine programs in SSA. This article reviews the epidemiological and clinical features of cervical cancer in SSA and describes the current status of HPV vaccine implementation in SSA countries. The review considers the challenges that will need to be addressed, and effective approaches to the design and implementation of HPV vaccination programs, using Rwanda as a case study. The review aims to provide suggestions and guidance to those involved in the development and implementation of HPV vaccination programs in SSA.

A reduction of melatonin function contributes to the acceleration of Alzheimer's disease (AD), and understanding molecular processes of melatonin-related signaling is critical for intervention of AD progression. Recently, we synthesized and tested a series of melatonin derivates with donepezil fragments in silico and in vitro. In this study, one of the most potent compounds, 3c, was studied in an in vivo rat model of pinealectomy (pin) and subsequent icvAβ1-42 infusion. Melatonin was used as a referent drug. The treatment with melatonin and 3c (10 mg/kg, i.p. for 14 days) exerted a beneficial effect on memory decline and concomitant rise of Aβ1-42 and pTAU in the hippocampus in the pin + icvAβ1-42 rats. Melatonin supplementation facilitated the non-amyloidogenic signaling via a non-receptor (histone deacetylase sirtuin 1, SIRT1) and receptor-related signaling (MT/ERK/CREB). The hybrid 3c derivate up-regulated the MT1A and MT2B receptors, pERK and pCREB. Our findings strongly support the hypothesis that melatonin-related derivates may become a promising drug candidate in AD therapy.

Sideritis royoi is described from limestone rocky habitats of the Port Massif (southern Catalonia, Spain). The species was first collected by the local botanist Lluís de Torres in the late part of the 20th century, but the specimens have remained unidentified positively in herbaria for over 40 years. Sideritis royoi likely belongs to section Sideritis subsection Hyssopifoliae and shows some morphological affinities with the relatively widespread South European species S. hyssopifolia L., but it much differs in having subspinescent upper leaves, main surfaces of the leaves glabrous or glabrescent, the main abaxial surface of the bracts without eglandular hairs, and shorter inflorescences. Weaker similarities were also observed with some species belonging to S. subsection Fruticulosae Obón &amp; D.Rivera. A description for the new orophilous species is provided, along with a detailed illustration, field photographs, and a comparison with closely related species. We include an assessment of its conservation status and a dichotomous key for identification of all the species of Sideritis subsection Hyssopifoliae.

The Konya Closed Basin (Quaternary, Central Turkey) is a graben basin which expands toward the east-west and it is controlled by faults on three sides: The Konya fault zone in the west, the Divanlar fault zone in the east and the Karaömerler fault zone in the north. Calcretes developed in relation to fault systems in the Konya region are concentrated in areas where faults cut Quaternary aged terrestrial deposits. In this study, it is aimed to elucidate the deposition conditions, geochemistry and age (with ESR method) of the calcareous deposits associated with faults in the Konya Closed Basin. Calcretes in the region existing as coatings, dust, nodules and layers are in the form of dolocrete and clayey calcrete. Dolocretes were deposited in the Quaternary terrestrial sediments on the ophiolitic rocks and geochemical data point to an ultramafic source. Bacterial community, clay, quartz minerals and calcite cement are observed in the calcretes formed in areas with limestone basement. According to the results of ICP-MS analysis of samples taken from Konya calcretes, the %MgO contents are between 0.99 and 7.7; CaO%: between 34.71 and 50.71; %SiO2 between 3.22 and 20.59. %MgO in dolocretes are between 11.65 and 21.01; %CaO between 8.44 and 29.57; %SiO2 values between 4.48 and 9.17 The δ13C and δ18O isotope values of calcretes range from -3.87 to -7.62 and from -3.62 to -7.45 respectfully. Average δ13C values indicate that calcrete formation took place under pedogenic condition or in shallow groundwater. The calcretes deposited in 3 locations around the city of Konya (on the Konya fault zone) were dated by using the Electron Spin Resonance (ESR) method and ages between 217.47 and 389.85 ky were obtained. The calcrete samples taken from the fault planes (dip-slip normal fault bordering the Upper Cretaceous Ophiolitic Mélange and the Quaternary Karahüyük Formation) gave a relative age for faulting as being 292.86 ky. This first dating study conducted in the Konya Fault Zone has provided important clues to elucidate the formation history of Konya Closed Basin (KCB) and the paleo-seismological past of Konya.

In this work a new hydroelectric basin modelling approach is described and applied to the Pontecosi basin, Italy. Several types of data sources were used to learn the model: a number of weather stations, satellite observations, Reanalysis dataset and basin data. With the goal of predicting the water level of the basin, the model was composed by three cascade modules. Firstly, different spatial interpolation methods, such as Kriging, Radial Basis Function and Natural Neighbours, were compared and applied to interpolate the weather stations data nearby the basin area to infer the main environmental variables (air temperature, air humidity, precipitation and wind speed) in the basin area. Then, using these variables as inputs, a neural network was trained to predict the mean soil moisture concentration over the area, also to improve the low availability due to satellite orbits. Finally, a non-linear auto regressive exogenous input (NARX) model was trained to simulate the basin level with different prediction horizons, using the data from the previous modules and past basin data (water level, discharge flow rate, turbine flow rate). Accurate predictions of the basin water level were achieved within 1 to 6 hours ahead, with mean absolute errors (MAE) between 2cm and 10cm respectively.

The forming of large rivers are the integral consequences of the deep earth process and the surface. In contrast to the hot topics for rivers related to orogenic domains, rift-related large rivers are largely ignored especially in deep time studies. The Cenozoic East Asia margin provides very good opportunity to observe this kind of rivers. It has been believed that basin-and-swell physiography dominated the East Asia margin and impeded the forming of large rives in the early Cenozoic. In this paper, we combined provenance analysis of East China Sea Basin, where is a crucial place to trace the river evolution in East Asia margin, and regional geologic constraints to reveal drainage reorganizations. Detrital zircon U-Pb ages from the Early Eocene sediments of the East China Sea Basin are firstly reported. Our results together with literature data demonstrate that regional provenance changes occurred at the middle Eocene from one singe age peak at ~110 Ma of proximal sources to multiple age spectrum derived from far inland. Source to sink analysis indicated that the North China Block and Korea Peninsular provided the most detritus. Sedimentation and tectonic features of rift basins in the potential source areas indicated that rivers flowed into Bohai Basin and Jianghan Basin cannot provide terrigenous clasts for the lower reaches in the Eocene. Contrastingly, the dominantly fluvial sediments across the Subei-South Yellow Sea Basin suggested external river system and a bypassing region since the middle Eocene, coinciding with provenance change in ECSB. All these demonstrated that a large river (East Asia River) established in east Asia margin in the middle Eocene and flowed southwestward approximately 1500km to the sea in southern ECSB. This river might last to the middle Miocene. The deep earth processes driven by Izanagi-Pacific ridge subduction resulted in the overfilled stage of Subei-South Yellow Sea Basin and the post-rift subsidence in west depression of ECSB, and thus facilitated the initiation of the EAR. Our finding shed new light on the evolving landscape in East Asia and showed how subduction of deep earth process controlled the initiation of rift-related large rivers.

Remote sensing data are essential for monitoring Earth’s surface waters, especially since the number of publicly available in-situ data is declining. Satellite altimetry provides valuable information on water level and its variations for lakes, reservoirs, and rivers. In combination with satellite imagery, the derived time series allow for monitoring lake storage changes and river discharge. However, satellite altimetry is limited in spatial resolution due to its measurement geometry, only providing information in nadir direction beneath the satellite’s orbit. In a case study in the Mississippi River Basin (MRB), this study investigates the potential and the limitations of past and current satellite missions to monitor basin-wide storage changes. For that purpose an automated target detection is developed and the extracted lake surfaces are merged with the satellites’ tracks. This reveals that the current altimeter configuration misses about 80% of all lakes larger than 0.1 km2 in the MRB, and still 20% of lakes larger than 10 km2, corresponding to 30% and 7% of surface area, respectively. Past altimetry configurations perform even worse. From the water bodies represented by a global hydrology model, at least 91% of targets and 98% of storage changes are captured by the current altimeter configuration. This will significantly improve with the launch of the planned SWOT mission.

Study of spatiotemporal dynamics of temperature is vital to assess changes in climate, especially in the Himalayan region where livelihoods of billions of people living downstream depends on water coming from the melting of snow and glacier ice. To this end, temperature trend analysis is carried out in Narayani river basin, a major river basin of Nepal characterized by three climatic regions: tropical, subtropical and alpine. Temperature data from six stations located within the basin were analyzed. The elevation of these stations ranges from 460 to 3800 m a.s.l. and the time period of available temperature data ranges from 1960–2015. Multiple regression and empirical mode decomposition (EMD) methods were applied to fill in missing data and to detect trends. Annual as well as seasonal trends were analyzed and a Mann-Kendall test was employed to test the statistical significance of detected trends. Results indicate significant cooling trends before 1970s, and warming trends after 1970s in the majority of the stations. The warming trends range from 0.028 ∘" style="position: relative;">∘C year−1" style="position: relative;">−1 to 0.035 ∘" style="position: relative;">∘C year−1" style="position: relative;">−1 with a mean increasing trend of 0.03 ∘" style="position: relative;">∘C year−1" style="position: relative;">−1 after 1971. Seasonal trends show highest warming trends in the monsoon season followed by winter, pre-monsoon, and the post-monsoon season. However, difference in warming rates between different seasons was not significant. An average temperature lapse rate of −0.006 ∘" style="position: relative;">∘C m−1" style="position: relative;">−1 with the steepest value (−0.0064 ∘" style="position: relative;">∘C m−1" style="position: relative;">−1) in pre-monsoon season and least negative (−0.0052 ∘" style="position: relative;">∘C m−1" style="position: relative;">−1) in winter season was observed for this basin. A comparative analysis of the gap-filled data with freely available global climate datasets show reasonable correlation thus confirming the suitability of the gap filling methods.

We use earthquake ground motion modelling via Ground Motion Prediction Equations (GMPEs) and numerical simulation of seismic waves to consider the effects of site amplification and basin resonance in Jakarta, the capital city of Indonesia. While spectral accelerations at short periods are sensitive to near-surface conditions (i.e., Vs30), our results suggest that, for basins as deep as Jakarta’s, available GMPEs cannot be relied upon to accurately estimate the effect of basin depth on ground motions at long periods (>1 s). Amplitudes at such long periods are influenced by entrapment of seismic waves in the basin, resulting in longer duration of strong ground motion, and interference between incoming and reflected waves as well as focusing at basin edges may amplify seismic waves. In order to simulate such phenomena in detail, a basin model derived from a previous study is used as a computational domain for deterministic earthquake scenario modeling in a 2-dimensional cross-section. A M_w 9.0 megathrust, a M_w 6.5 crustal thrust and a M_w 7.0 instraslab earthquake are chosen as scenario events that pose credible threats to Jakarta, and the interactions with the basin of seismic waves generated by these events were simulated. The highest PGV amplifications are recorded at sites near the middle of the basin and near its southern edge, with maximum amplifications of PGV in the horizontal component of 200% for the crustal, 600% for the megathrust and 335% for the deep intraslab earthquake scenario, respectively. We find that the levels of ground motion response spectral acceleration fall below those of the 2012 Indonesian building Codes's design response spectrum for short periods (< 1 s), but closely approach or may even exceed these levels for longer periods.

The global energy landscape is undergoing a transformative shift, and the potential of LNG as a major energy source is a topic of intense debate. In order to meet the growing demand for sustainable energy supply, it is crucial to maximize the efficiency and environmental friendliness of the LNG supply chain. This research aims to leverage computational modeling and optimization techniques to enhance the production units involved in LNG production. By harnessing the power of advanced algorithms and simulations, we can identify and implement innovative strategies that minimize energy consumption, reduce greenhouse gas emissions, and enhance the overall sustainability of LNG. Through this study, we seek to uncover novel approaches to address the challenges faced by the LNG industry, including improving operational efficiency, optimizing liquefaction processes, and enhancing the utilization of natural resources. By integrating cutting-edge computational tools and considering environmental factors, we aspire to pave the way for a more sustainable and environmentally friendly future powered by LNG. By exploring the immense potential of computational modeling and optimization, we strive to contribute to the ongoing efforts in advancing energy sustainability and shaping the future of LNG as a crucial global energy source."In this paper, our focus is on simulating and optimizing the process of converting natural gas to LNG. Our goal is to achieve the minimum energy consumption per ton of LNG produced. Through our research, we have identified that utilizing a three-stage exchanger is the most effective approach for minimizing energy consumption in an LNG industrial production unit. Moreover, we have discovered that the outlet pressure from the compressor and the type of refrigerant in the cooling system play significant roles in determining the rate of energy conservation. By carefully considering these factors and optimizing their settings, we can further enhance the overall energy efficiency of the LNG production process. Our research aims to provide valuable insights and guidance to industry professionals and decision-makers in the LNG sector. By implementing the findings of this study, we can contribute to the sustainable development and utilization of LNG as a cleaner and more environmentally energy source. Friendly It's great to see the optimized parameters for the refrigerants and pressure settings in the liquefaction and subcooling cycles. With the mass fraction of 0.89 for methane and 0.14 for ethane in the liquefaction cycle, and 0.59 for methane and 0.3 for nitrogen in the composition for achieving energy efficiency in the LNG production subcooling cycle, The optimized outlet pressure of 650 kPa for the compressors in the liquefaction cycle and 1800 kPa for the subcooling cycle furtherr ccontribute to minimizing energy consumption. Based on your findings, the amount of consumed energy at 14.81 kW per ton of produced LNG highlights the success of the optimization efforts. Reducing the energy consumption per ton of LNG produced is a significant accomplishment towards achieving energy sustainability and environmental friendliness in the LNG industry. These results demonstrate the importance of computational modeling and optimization in identifying the best parameters for eenhancing energy efficiency in LNG production. By implementing these optimized settings, we can work towards a more sustainable future with reduced energy consumption and lower environmental impact

(1) Background: Respiratory infections are a major public health problem worldwide, with potentially serious consequences. Indeed, these infections remain one of the main causes of morbidity and mortality in children under 5 years old in developing countries. Etiological information on respiratory infections is crucial for prevention and case management strategies. This systematic review aims to describe the etiology of respiratory infections reported in studies carried out in sub-Saharan African countries; (2) Methods: Using PubMed, HINARI and Google scholar search engines, a systematic search was carried out to identify published articles on the etiology of viral and/or bacterial respiratory infections in sub-Saharan Africa in patients of all ages. We have only considered data from sub-Saharan Africa. Papers published from 2010 to 2021, in English or French have been included in this review; (3) Results: After reviewing 115 articles reporting studies carried out in the African continent, only 32 articles were selected of which, studies were conducted in 15 sub-Saharan African countries, including 6/32 (18.75%) in Cameroon. Twenty (62.5%) were cross-sectional studies, and twenty-four (75%) were hospital-based investigations. In these studies, RT-PCR and culture methods were respectively used for viruses and bacteria investigations. Respiratory syncytial virus was the most frequently identified, with prevalence ranging from 0.6% to 59%, followed by rhinovirus (9.3% -73%), influenza virus (flu) A/B (0.9%-69.1%), and human adenovirus (0.9% - 30.8%). Streptococcus pneumoniae (14.2% - 96%), followed by Haemophilus influenzae type b (2.5% - 54%), and Klebsiella pneumoniae (1.4% - 49.9%) were the most frequently detected bacteria; (4) Conclusions: This review has reported that many pathogens, mainly viruses, are associated with acute respiratory infections in sub-Saharan Africa in both children and adults. Unfortunately, the limited geographical distribution of data across sub-Saharan Africa does not allow most of countries to develop an effective strategy for the prevention and treatment of respiratory infections.

Hemoglobin based oxygen carriers (HBOC) as blood substitutes are one of the great hopes of modern transfusion and emergency medicine. After the major safety-relevant challenges of the last decades seem to be largely overcome, current developments have in common that they are affected by degradation and excretion at an early stage in test organisms. Several possible mechanisms that may be responsible for this are discussed in the literature. One of them is CD163, the receptor of the complex of haptoglobin (Hp) and hemoglobin (Hb). The receptor has been shown in various studies to have an affinity for Hb in the absence of Hp. Thus, it seems reasonable that CD163 could possibly also bind Hb within HBOC and cause phagocytosis of the particles. In this work we investigated the role of CD163 for the uptake of our HbMP (hemoglobin sub-micron particles) in monocytes and additionally screened for alternative ways of particle recognition by monocytes. In our experiments, blockade of CD163 by specific monoclonal antibody proved to partly inhibit HbMP-uptake by monocytes. It appears however, that several other phagocytosis pathways for HbMP might exist, independent of CD163 and also Hb.

Though there has been a decline in the number of new cases of viral hepatitis-induced acute liver failure in Europe and the United States of America, viral hepatitis still remains the leading cause of acute liver failure in Asia-Pacific and South America. However, the epidemiology of viral-hepatitis-induced acute liver failure in sub-Saharan Africa-the world epicenter of viral hepatitis-is unclear. The aim of this review was to collate data on the incidence, prevalence, specific etiologic agents, features/diagnosis, treatment and prognosis of viral-induced acute liver failure in sub-Saharan Africa. One hundred and forty-seven cases of viral-induced acute liver failure were recorded in 11 studies conducted in six countries between 1981-2020. Etiological agents were: Hepatitis viruses A, B, C, and E, as well as Adenovirus, Enterovirus, Parvovirus, Herpes Simplex Virus (HSV) and EBV. HAV was the most frequent in paediatric subjects: (11/16) 69% and (19/30) 63%. HBV was the only etiological agent in the study that only included adults. HEV (genotype 2 in one study) contracted amidst hepatitis E outbreaks was the most commonly reported cause of ALF in pregnant women. Treatment was mainly supportive, and liver transplantation reported only in South Africa. Where reported, case fatality rates were high. In conclusion, viral-hepatitis induced acute liver failure is largely understudied in sub-Saharan Africa. The few available data are consistent with literature from the other parts of the world regarding aetiologic agents. Liver transplantation is not available in most sub-Saharan African countries, and short-term case fatality rates of individuals with acute liver failure could outstrip current rates from the other world regions.

Studies shows that, normal to high serum 25(OH)D status appears to have some beneficial influence on the incidence and severity of some, though not all, types of infections. However, studies with vitamin D supplementation on young children produced conflicting results with respect to the level of vitamin D deficiency among common medical illnesses among children. Method: A systematic review of literatures from PubMed, CINAHL, Web of science, global health and Google scholar electronic databases was conducted to assess the pooled prevalence of vitamin D deficiency among healthy and sick children in sub-Saharan Africa. The data was extracted by two authors independently using standard data extraction format and STATA Version 14 was used for analysis. The heterogeneity of the studies was assessed by using I2 test. A random-effects model was used to estimate the pooled prevalence among both healthy and sick children. Presence of publication bias was checked using Funnel plot and Egger's test. Result: A total of 1212 articles were identified by the total search of utilized data bases of which 13 papers fulfilled the inclusion criteria and accessible with full document. The meta-analysis revealed that the pooled prevalence of vitamin D deficiency among healthy children in this study was 50.06% (95%CI 33.46%, 66.67%) with mean serum vitamin D level of 41.06 nm/L (CI range from 23.82nm/L to 58.31nm/L). The pooled prevalence among the sick children was 39.36% (CI 20.57%, 57.96%) with 66.96nm/L (95% CI 54.81nm/L, 79.11nm/L) mean concentration of vitamin D. Comparing the two level of the pooled prevalence, the prevalence among the healthy children was significantly higher compared to those who have common medical illnesses and the pooled mean concentration among the sick was much higher than the mean concentration among healthy children. Conclusion: The level of pooled prevalence among both group of population was significantly of public health concern and the prevalence among the healthy children was much higher among the sick children implying the need for reconsideration of available recommendations for the prevention of vitamin D deficiency

To bring to the fore the aim of this research, effects of fluctuating temperature, was measured against food and nutrition security in the region using food production index, and undernourished population growth rate as proxies; controlled over share of arable land, irrigation, population and labour share for agriculture. Dynamic panel of generalized method of moments (GMM) was adopted, the period 2000 to 2016 were considered and 29 countries in sub-Sahara Africa were selected within the empirical framework of global water balance as mentioned by Rai and Singh (2012). Findings from the study reveals that the short run effect of temperature increase in degrees pose at least -3.1% negative and significant impact effects on the food production while the long run elasticity hits -7.5% and the controlled effect on arable land revealed a positive impact on the food production to the tune of 3.9%. Contrarily, arable land expansion reduces the under nourished population by -8.55%. Population increase on the other hand increases undernourished population in the region to the tune of 11.95%. The study therefore recommended expansion in the arable land and encourages population control policy in order to negate the undesired effects of temperature on food and nutritional security.

The novel COVID-19 pandemic prompted an unprecedented Institutional reaction to aggregate existing capacity from silos of research laboratories to establish a multidisciplinary research laboratory for COVID19 testing. In less than two weeks, resources were mobilized from the community to strengthen public health response and epidemic control. Such strengthening of institutional research capacity to support public health response contributes to a natural knowledge transfer, facilitates collaboration, and generates new frontiers for knowledge production that should ultimately lead to professional development and retention of skilled human resources. This report describes the pre-established mechanisms and involvement of the authors that made it possible to set-up a multidisciplinary laboratory in a remarkably short period of time. We also discuss the opportunities and sustainability of multidisciplinary laboratory research post-COVID19. Existing institutional capacity can be repurposed to establish multidisciplinary research laboratories to support the strengthening of basic and clinical translational research capacity in resource limited settings and impact on public health and scientific knowledge for socioeconomic development.

This work presents noble composites of AAILs@MCM-48 by functionalizing ordered mesopo-rous silicon MCM-48 with two amino acid-based ionic liquids (AAILs) ([Emim][Gly] and [Em-im][Ala]) to improve carbon capture and selectivity of CO2 over nitrogen. Thermogravimetric and XRD analyses of the composites show that the MCM-48 support's thermal and structural in-tegrity was preserved after the AAILs were encapsulated. An N2 adsorption-desorption study at 77 K also confirms AAIL encapsulation in the porous support. Under post-combustion flue gas conditions, both [Emim][Gly]@MCM-48 and [Emim][Ala]@MCM-48 demonstrated improved CO2 adsorption in comparison to unmodified MCM-48, with a CO2 partial pressure of around 0.15 bar. In terms of maximal CO₂ uptake, the 40wt%-[Emim][Gly] composite outperformed the others at 303K, with values of 0.74 and 0.82 mmol g-1, respectively, at 0.1 and 0.2 bar. These numbers show a 10x and 5x increase, respectively, as compared to the pure MCM-48 under iden-tical conditions. In addition, the selectivity of the composites was improved significantly, at 0.1 bar, the selectivity of composites containing 40wt% [Emim][Ala] increased to 17, compared to 2 for pristine MCM-48.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.

This research seeks to advance the understanding of ecological management in the Huaihe River Basin, China. The spatiotemporal variability of the Normalized Difference Vegetation Index (NDVI) and its underlying driving forces are examined utilizing SPOT-NDVI data covering the period 2000-2019. Linear regression analysis is employed to quantify trends and assess the statistical significance of NDVI variations. A differencing approach is subsequently applied to discern the variability in NDVI. The distribution of its spatial pattern stability over 20 years is explored through the coefficient of variation. Lastly, the Geodetector method is utilized to elucidate the driving factors influencing NDVI dynamics. The results indicate that the overall NDVI is generally high, with an overall growth rate of 0.00148/year, and 2010 is identified as a significant inflection point in the trend. NDVI values are notably lower in urban areas, corresponding to urban expansion, except for regions near rivers and lakes. Land use type emerges as the strongest explanatory factor for NDVI among single factors, with climate factors exhibiting a relatively weaker degree of explanatory force. These findings suggest that the overall NDVI in the Huaihe River Basin is high, indicative of a vegetation condition that continues to improve.

Time series ground deformation monitoring and reservoir parameter inversion are crucial for the dynamic assessment of oilfield resources and sustainable exploitation in an oilfield. As one of the regions with the richest oil reserves in China, the oilfield areas in the western Qaidam Basin are selected as a typical study area. Firstly, we used SAR images collected by the Sentinel-1A satellite from January 2021 to December 2022 and applied the Multidimensional Small Baseline Subset (MSBAS) method to obtain vertical and east-west deformation measurements. On this basis, a nonlinear Bayesian inversion method was applied to model the shallow reservoir in a series of complex deformation areas, based on a single-source model and a multi-source model, respectively. As a result, the ground deformation monitoring results obtained by long time series InSAR clearly reflect the uneven ground deformation caused by the oil extraction and water injection operation process. There is slight subsidence in the Huatugou oilfield, while significant uplift deformation occurred in the Ganchaigou oilfield and the Youshashan oilfield, with a maximum uplift rate of 48 mm/year. Further analysis indicates that the introduction of the 2D deformation field helps to improve the robustness of oilfield reservoir parameter inversion. Moreover, the dual-source model is more suitable than the single-source model for inverting complex deformation reservoir parameters. This study not only fills the blank of InSAR deformation monitoring for the oilfields in the western Qaidam Basin but also provides a theoretical reference for model and method selection of reservoir parameter inversion in other oilfields.

The detrital compositions in sandstone are important recorders of sedimentary provenance and transport, both of which have significant implications for the lithology, age and tectonic evolution of provenance. Through detailed identification and analysis, a high content of volcanogenic compositions (27.6%) was discovered in Shanxi formation of Daniudi Gas Field, Ordos Basin, which is much higher than that of the previous study. The volcanogenic compositions include volcanogenic quartz, lava fragments (dominated by various kinds of rhyolite fragments), tuff fragments, and tuffaceous matrix. In addition, at least 2 volcanic ash layers were discovered. Although the metamorphic rocks of the Precambrian succession in the ancient land of Yin Mountain are usually considered the primary source of the Shanxi formation, it is most likely that the volcanogenic compositions were derived from intermediate-acidic volcanic materials that accumulated in the Daqingshan area during the Late Carboniferous to Early Permian. Those volcanogenic compositions are mainly transported by flowing water rather than by air from provenance to basin. And the accumulation of volcanic materials in the Daqingshan area was controlled by volcanic eruptions occurring solely in this area, rather than by the Inner Mongolia Orogenic Belt. Those volcanic eruptions related to the southward subduction of the Paleo-Asian Ocean Plate beneath the northern margin of the North China Plate in Late Carboniferous to Early Permian. The active continental margin related to the subduction of the Paleo-Asian Ocean Plate lasted until at least the Early Permian, and the closure of the Paleo-Asian Ocean must have occurred later than the Early Permian.

In the context of the rural revitalization strategy, it is urgent to accurately grasp the spatial differentiation characteristics and influencing factors of rural settlements in underdeveloped arid inland river basins. Taking the Shiyang River Basin as an example, the rural settlements from 2000 to 2019 were obtained by visual interpretation using satellite remote sensing data and official statistical data. Following the logical of "state characteristics - evolutionary patterns - influence factors - layout optimization", the average nearest index, gravity-center migration model, spatial statistical analysis and other methods were used combine with GIS. The spatiotemporal pattern evolution characteristics of rural settlements in the past 20 years have been analyzed. The results revealed the following: 1) The distribution pattern of rural settlements in the study area is sheet-like and strip-shaped. The projects in the southeast are mostly distributed in a patchy pattern with high density, while the characteristics in the west and north are exactly opposite. The objects in the south are distributed in the alluvial area of rivers, while settlements in the north are located in the oasis area. 2) From 2000 to 2019, the scale of rural settlements in the Shiyang River Basin, where simultaneous occurrence of new-built and disappearing phenomena, shows an expansion trend that fast firstly and then slow. Spatially, rural settlements in the basin show a trend of clustering towards the southwest. 3) The distribution characteristics of rural settlements are close to water and roads, greatly influenced by urban-rural integration and ecological migration. The results will provide scientific basis for accelerating the modernization of rural areas, and the construction of new rural areas according to local conditions.

The acquisition of regional, 1 metre resolution LIDAR in the PNG Highlands combined with 3D modelling in MoveTM has revolutionized our understanding of the evolution of the Porgera gold mine and areas of new potential. The new 3D model demonstrates active pull-apart basins along a regional transfer during ongoing fold and thrust deformation. When overlain on regional aeromagnetic data, new potential is revealed. The Porgera gold mine is one of the richest in the world and lies in a wide valley at an elevation of 2800m surrounded by mountains up to 4000m high in the middle of the PNG Highlands. It lies along a major lineament, the Porgera Transfer Zone (PTZ), cutting across the orogen that is associated with a 50 km offset of the ophiolite belt. To the NW of the mine there is an extensive belt of low- to high-grade metasediments that formed in deep water during Jurassic rifting, but were metamorphosed during Eocene subduction to the north. Subduction ceased due to accretion of the Sepik Terrane which caused inversion and mild erosion of the Porgera area. The Late Oligocene onset of wrenching in the Mobile Belt to the north placed that area into extension, emplacing metamorphic core complexes, and led to regional subsidence in the Early Miocene. Collision of the margin with the Melanesian Arc in the Middle Miocene caused Late Miocene to Pliocene orogenesis creating the broad mountain belt that we see today, that is still active, as shown by the 2018 MW 7.5 earthquake. Regional mapping of the area using high resolution LIDAR in association with limited field mapping, analysis of gravity and magnetics data and drilling of 300-500m deep core-holes has allowed development of a detailed 3D structural model. The Porgera valley is constrained laterally by the Eastern Boundary and Western Boundary dextral strike-slip faults that lie along the PTZ cutting across the orogeny. However, whilst the position and nature of the faults is clear, due to bending, fracturing and offset of major synclines and anticlines, the faults do not crop-out as significant through-going features. Rather, the dextral offset of basement is soft-linked to the Tertiary limestones at surface due to intervening thick, ductile Cretaceous shales. Fold and thrust structures are ubiquitous in the Tertiary limestones, but the youngest structural features are large extensional faults, particularly around the Porgera valley. The intrusive underlying the Porgera ore-body was emplaced at 6.0+-0.3 Ma, the time of maximum compression during orogenesis. At this time the Eastern Boundary fault and Western Boundary fault were both active allowing a pull-apart basin to form locally along the PTZ at the south-eastern boundary of the Jurassic metasediments. This enabled emplacement of the intrusive. The gold-bearing fluids from the intrusive and metasediments were brought up through the Mesozoic muds to the contact with the Paleogene carbonates where the Porgera ore body was emplaced.

We used LA-ICP-MS U-Pb data for detrital zircon to constrain the Maximum Depositional Age (MDA) and provenance of clastic sedimentary rocks of the Volyn-Orsha sedimentary basin, which filled an elongated (~625×250 km) depression in SW Baltica and attained ~900 m in thickness. Eighty-six zircons out of one hundred and three yielded concordant dates, with most of them (86 %) falling in the time interval between 1655 ± 3 and 1044 ± 16 Ma and clustering in two peaks at ca. 1630 and 1230 Ma. The remaining zircons yielded dates older than 1800 Ma. The MDA is defined by a tight group of three zircons with a weighted average age of 1079 ± 8 Ma. This age corresponds to the time of a clockwise ~90° rotation of Baltica and the formation of the Grenvillian – Sveconorwegian – Sunsas orogenic belts. Subsidence was facilitated by the presence of eclogites derived from subducted oceanic crust. The sediments of the Orsha sub-basin in the northeastern part of the basin were derived from the local crystalline basement, whereas the sediments in the Volyn sub-basin, extending to the margin of Baltica, were transported from the orogen between Laurentia, Baltica, and Amazonia.

Due to the use of structural and seismic techniques an attempt has been made in this study to determine the hydrocarbon potential and future exploration in Pakistan's Lower Indus basin area and offshore region. In addition to the possibility of hydrocarbon accumulation, the major goals of this research are to analyze structural patterns in the subsurface of the study region, identify the horizons of various formations using surface seismic, and interpret seismic lines. Seismic data has been used to find and integrate the exposed Cretaceous/Tertiary basalt at Ranikot in the lower Indus basin to the well-known Deccan basalts of the Indo-Pak plate, which is the secondary goal of the current investigation. According to the interpretation of seismic data, the Indo-Pakistan plate has experienced rifting because of tectonic activity. Graben and horst structures have been identified in the study area horizon, which indicates that the area has undergone major structural and depositional changes. While faults provide a pathway for hydrocarbons to migrate from their source to reservoir rock, grabens are principally responsible for the accumulation of hydrocarbons. We further deduce that the prior exploration failures in the area were due to a lack of knowledge of the subsurface formations and structural trends, which are essential for characterizing the hydrocarbon play and trap features. Our results can be productive for the local hydrocarbon drilling projects as well as worldwide tectonic stratigraphy studies on passive continental edges.

The direct radiative effects of atmospheric aerosols are essential for climate, as well as for other societal areas, like the energy sector. The goal of the present study is to exploit the newly devel-oped ModIs Dust AeroSol (MIDAS) dataset for quantifying the direct effects on the downwelling surface solar irradiance (DSSI), induced by the total and dust aerosols amount, under clear-sky conditions and the associated impacts on solar energy for the broader Mediterranean basin, over the period 2003 – 2017. Aerosol optical depth (AOD) and dust optical depth (DOD) derived by the MIDAS dataset, along with additional aerosol and dust optical properties and atmospheric variables were used as inputs to radiative transfer modeling to simulate DSSI components. A 15-year climatology of AOD, DOD and of clear-sky Global Horizontal Irradiation (GHI) and Direct Normal Irradiation (DNI) was derived. The spatial and temporal variability of the aerosol and dust effects on the different DSSI components was assessed. Aerosol attenuation of annual GHI and DNI range from 1-13% and 5-47%, respectively. Significant attenuation by dust 2-10% and 9-37% was found over North Africa and the Middle East, contributing to 45-90% of the total aero-sol effects. The mean GHI and DNI attenuation during extreme dust episodes reached values up to 12% and 44%, respectively, for different areas. After 2008 a decline of aerosol effects on DSSI was found, attributed mainly to the dust component. Sensitivity analysis using different AOD/DOD inputs from Copernicus Atmosphere Monitoring Service (CAMS) reanalysis dataset, revealed CAMS underestimation of aerosol and dust radiative effects compared to MIDAS, due to slight AOD and stronger DOD underestimation, respectively.

Human activities mostly impact the trend and direction of surface water, groundwater, and other river basin resources in the watershed in Africa. Human activities influence river flows and the water quality at both highlands and lowlands. A watershed is indeed a conserved area of land that collects rain and snow and empties or penetrates into ground water sources. The act of managing the activities around the watershed is the Integrated Watershed Management while considering the social, economic, and environmental issues, as well as community interests to manage water resources sustainably. These watersheds, river basins, and groundwater resources provide important services for communities and biodiversity. This paper reveals that the best way to protect groundwater resources is on a watershed basis using IWM. This technique enables us to handle a variety of concerns and objectives while also allowing us to plan in a complicated and uncertain environment. IWM involves cooperation and participation from a wide range of community interests and water users, including municipalities, companies, people, agencies, and landowners, for stakeholders' input to be successful. All of the strategies and plans are produced concerning one another, as well as the overall conditions of the watershed, local land uses, and specific issues.

The Sanshui Basin (SSB) is located at the northern continental margin of the South China Sea and characterized by a continental rift basin. The bimodal volcanic rocks in SSB record the early Cenozoic magmatic activity in the South China Block, on the magmatic evolution process of bimodal volcanic rocks are poorly understood. Clinopyroxenes in bimodal volcanic rocks in the SSB provide an opportunity to investigate the magma process during magma ascent. We classified nine types of clinopyroxene phenocrysts according to the different compositions and textures types in cogenetic basalt-trachyandesite-comenditic trachyte, the composition of unzoned clinopyroxene have an evolution sequence of diopside- hedenbergite- aegirine with the decrease of Mg#, and the trace element contents of unzoned clinopyroxenes also increase systematically during magma evolution, indicating that the genesis of clinopyroxene dominated by fractional crystallization in a closed magma system; however, the clinopyroxenes with reverse zoning and multiple zoning record the process of magma mixing and recharge indicating an open magma system. Whilst fractional crystallization is the dominated process, magma mixing, recharge, and crystal settling complicate magma evolution. Thermobarometric calculations show that clinopyroxene phenocrysts in bimodal volcanic rocks of SSB are distributed in the whole crust during magma ascent. We have established a magma plumbing system, which provides a new constrain for the complex magmatic evolution history in the SSB by detailed mineral-scale analysis.

Satellite-based rainfall estimation products provide a vital alternative source of rainfall data in areas where conventional precipitation measurement is not readily available. In order to facilitate the use of these products there is the need to evaluate their accuracies. This study evaluated the accuracy of three satellite rainfall products; TMPA 3B42RT, TMPA 3B42 and CMORPH in the Pra basin (23,330 km²) of Ghana. The evaluation was through the point-to-pixel method by comparing 0.25°x 0.25° satellite grids to gauged rainfall based on gauge locations and analyzed statistically using correlation coefficient (r), bias and percent bias (pBias) as the performance verification methods. Seven (7) gauge stations with no missing data for the period of 2003-2008 was used in the evaluation. The analysis was based on daily, monthly, annual and seasonal timescales. Our results showed a good correlation between the TMPA products and the gauged data on all timescales considered. The CMORPH on the other hand showed huge overestimation at all gauge locations. The TMPA 3B42 was seen to be the best amongst the three products. The overall rainfall in the basin was well depicted by the TMPA 3B42 and 3B42RT. Although there wasn’t a perfect match between the 3B42RT and 3B42 products and the gauged rainfall, these products can be used to supplement gauged rainfall measurements in the basin and in estimation of rainfall in ungauged basins with similar characteristics.

This essay critically discusses the integration of queer theory into human geography while emphasizing its ties to the principles of traditional geography. The need for a separate sub-discipline called queer geography is questioned. At the same time, legitimate concerns about possible departures from the fundamental goals of geography and the risks of anachronistic interpretations in applying modern concepts to historical landscapes are acknowledged. In this discourse, we strongly advocate for values such as freedom of speech, freedom of expression, and international human rights. It is important to emphasize that it is not the intent of this essay to denigrate campaigns for feminism or equality or to disparage the scholarship that emerges from the application of queer theory. On the contrary, we recognize the emergence of gender theories out of a need to advance social justice approaches. We believe that traditional human geography, itself, is capable of comprehensively examining space, time, and the complexity of human experience and offering workable solutions within its established framework. We therefore believe that the inclusion of queer theory can be harmoniously integrated into the contours of human geography, eliminating the need for a separate sub-discipline while preserving the integrity and purpose of the discipline.

: Urinary schistosomiasis caused by the parasite Schistosoma haematobium is the most common form of schistosomiasis. This parasite has a high potential for genetic exchange within parasite populations giving rise to the genetic diversity that is important for its survival. Genetic differ-ences may lead to some parasite strains being more immunogenic which may have a negative impact on management and control of schistosomiasis. Therefore, understanding these genetic differences in the parasite may lead to better management of the disease. A literature search was done on PubMed, African Journals online and Google scholar using predefined search terms such as urinary schistosomiasis, S. haematobium, genetic diversity in sub-Saharan Africa in com-bination with Boolean operators (AND, OR). The search included studies published from 2000-2020 that emphasised on genetic diversity of Schistosoma haematobium in sub-Saharan Africa. Sixteen studies from 18 sub-Saharan African countries that met the inclusion criteria were se-lected. Most studies conducted in these countries showed a high genetic diversity of Schistosoma haematobium studies with microsatellite markers being the most commonly used method for ge-netic diversity determination. Fisher’s exact test showed that the distribution of genetic diversity in sub-Saharan African regions was not statistically significant (p=0.768). The highest number of studies on genetic diversity of Schistosoma haematobium were conducted in West Africa with Ni-geria and Zimbabwe in Southern Africa conducting the most studies, 4/36 (11%) each. Results obtained show the need for continued monitoring of genetic variations in Schistosoma haemato-bium in sub- Saharan Africa. This will aid in understanding the epidemiology of disease, ad-vancing novel treatment and vaccine strategies.

Mobile health devices are emerging applications that could help deliver point-of-care (POC) diagnosis, particularly in settings with limited laboratory infrastructure, such as sub-Saharan Africa (SSA). The advent of coronavirus has resulted in an increased deployment and use of mHealth-linked POC diagnostics in SSA. We performed a systematic review and meta-analysis to evaluate the accuracy of mobile-linked point-of-care diagnostics in SSA. Our systematic review and meta-analysis were guided by the Preferred Reporting Items requirements for Systematic Reviews and Meta-Analysis (PRISMA). We exhaustively searched PubMed, Science Direct, Google Scholar, MEDLINE, and CINAHL with full-text via EBSCOhost databases from mHealth inception to March 2021. The statistical analyses were conducted using OpenMeta-Analyst software. All 11 included studies were considered for the meta-analysis. The included studies focused on malaria infections, Schistosoma haematobium, Schistosoma mansoni, soil-transmitted helminths, and trichuris trichiura. The pooled summary of sensitivity and specificity estimates were moderate compared to the gold reference standard. The overall pooled estimates of sensitivity, specificity, positive likelihood ratio, negative likelihood ratio and diagnostic odds ratio of mobile-linked POC diagnostic devices were as follows: 0.499 (95% CI: 0.458-0.541); 0.535 (95% CI: 0.401-0.663); 0.952 (95% CI: 0.60-1.324); 1.381 (95% CI: 0.391-4.879); and 0.944 (95% CI: 0.579-1.538), respectively. Evidence shows that mobile-linked POC diagnostics' diagnostic accuracy is presently moderate in detecting infections in sub-Saharan Africa. Future research is recommended to evaluate mHealth devices' diagnostics with excellent sensitivities and specificities in diagnosing diseases in this setting.

United Nations Framework Conventions on Climate Change (UNFCC) conventions in their conference of parties (COPs) has continuously considered and agreed reducing emission level in order to minimize the impact of global climate change. Reducing emission due to deforestation and degradation (REDD) ,was considered as one of the major activities in this regard during Kyoto protocol in 2009 which laid foundation for the participating countries to be compensated financially for reduced carbon emission. Mexico convention -2012 required the countries to develop and implement a transparent and consistent monitoring, reporting and verification (MRV) process. Later in Paris agreement-2015, the parties agreed to limit the global warming to 2 degree centigrade and with further efforts to 1.5-degree centigrade furthering entailing the parties to prepare and communicate nationally determined contributions (NDCs) every five years. Nepal aimed to decrease the average annual deforestation rate by 0.05 percent from existing 0.44 percent in the terai region and 0.1 percent in the Chure. Nepal decided to develop its forest reference level (FRL) in national level for the historical period 2000-2010 considering Carbon dioxide and carbon pools above and below ground. As per the Forestry Sector Strategy, Nepal aims to increase carbon stock growth by at least 5% by 2025 as compared to 2015 and decrease mean annual deforestation rate to 0.05. After major change in administrative division in Nepal, forest management responsibility has shifted down to the Sub-national level. But forest resource studies have not been conducted yet in these levels. Despite a small country, Nepal has at least four clear physiological regions. The amount of carbon stock stored by different forest type are different depending upon species distribution, carbon volume and density for each species, and their distribution along ecological and physiological regions. Sal (shorea Robusta), for example, having one of the highest carbon densities, is a major forest types in Nepal. The purpose of this study was to generate forest map of the country, calculate carbon stock, gain and loss, and their rate in each province due to deforestation/afforestation using remote sensing data. Further Sal forest map was generated and its contribution in carbon stock was calculated using averaged national carbon density as well as using regional density method. According to the study, around 5.1 million hectares of Nepali land was forest in 2015 increasing from 4.2 million hectares in 2005. However, Sal forest has decreased during the same period. Province 1 contributed the maximum (130 Tg) and Province 2 the minimum (40Tg) of Carbon stock in 2015. Using the conventional method of calculation with national average density (108.08 t/ha), a total of 36.7T CO2 yr-1 carbon sink was observed in the Country. Whereas, with the new approach of calculation, a total of 44.7 T CO2 e of carbon sink per year was estimated during the same period. This approach holds potential for qualifying as an MRV process of Nepal. The subnational level forest and carbon statistics produced during this study can be important assets for the better forest governance. This can also pave way for policy formation and preparation of action plan for sustainable forest management and intervention strategy and obtaining better financial incentives participating in the reduction of emission due to deforestation and forest degradation (REDD) plus programs.

A cross-sectional study was carried out to determine the prevalence of subclinical mastitis (SCM) among medium to large scale household dairy farms in southwestern district, Jhenaidah, Bangladesh during July to December 2019. A total of 78 (n=100) lactating cows from household dairy farms (N=32) having three or more dairy cows were selected randomly as sampled populations. Milk samples were screened for SCM by using Surf Field Mastitis Test (SFMT). The prevalence of SCM varied among farm level [71.9% (95% CI: 53.3-86.3)], individual animal level [67.9% (95% CI: 56.4-86.3)] and quarter level [29.5% (95% CI: 24.5-34.9)]. Descriptive statistics represented the farmers and farm demography, characteristics of the sampled population, and overall management feature. Random Effect Logistic Regression identified, Body Condition Score (BCS) [OR=3.8 and 2.9, at cows level and quarter level respectively (BCS-2 vs. BCS-≥3)], and breed [OR=5.1 and 2.9, at cows level and quarter level respectively (HF× Sahiwal vs. HF × Local)] as potential risk factors. This study shows that SCM is highly prevalent in the study area, which is a major threat to the dairy industry's production performance. Regular screening by SFMT, proper hygiene, improve the management system, and farmer’s awareness is required to control the disease.

The eruption of the COVID-19 pandemic has affected every sphere of life and may forever change how we have always lived and conducted our businesses, and no one can resist the wind of change that is blowing. Of all the sectors of governance, the educational sector, particularly at the tertiary level, appears to have been most greatly affected and therefore requires a more pragmatic approach to resolution. As of 29th June, Sub-Sahara Africa has reported 382,190 cases of COVID-19. In rejoinder to the virus epidemic, several Sub Sahara African governments implement the resolution to slam learning institutions to enclose the infection. Consequently, advanced schooling institutions obliged to reorganize their loom, becoming more digitally become forward, and changing to online platforms.

In this paper, the validity of the Wagner’s law is investigated in tenth selected Sub- Saharan African countries, namely Botswana, Equatorial Guinea, Mauritania, Nigeria, South Africa, Sierra Leone, Tanzania, Ethiopia, Madagascar, and DR Congo. Five variants of the Wagner’s law were tested for the period 2005-2014, using panel econometric approaches encompassing cointegration and causality. The study found a long run relationship between the public expenditure and the various explanatory variables used as proxies of income. The long-run causality tests indicate that there is bidirectional causality between expenditure and income in all models with the exemption of the Gupta model. It is concluded that for Sub-Saharan Africa, both the Wagner’s law the Keynesian hypothesis tend to be valid under the period of investigation. The explanation is that there has been the tendency for public expenditure to grow relative to national income (Wagner’s law) and that public expenditure is a policy instrument (an exogenous factor) for improving national income (Keynesian hypothesis) during the 10-year period.

An important aspect of the new sustainable development goals (SDGs) is a greater emphasis on reducing the health impacts of urban ambient air pollution (AAP) in developing countries. Meanwhile, the burden of disease attributable to AAP in sub-Saharan Africa (SSA) is growing, yet estimates of its impact in the region are likely underestimated due to a lack of air quality monitoring, the paucity of epidemiological studies, and important population vulnerabilities in the region. The lack of studies in the SSA region also represents an important global health disparity and environmental justice issue because thousands of air pollution health effects studies have been conducted in Europe and North America rather than in some of the most polluted regions of the world, such as SSA. In this review, we synthesize all of the ambient air pollution epidemiological studies that have been conducted in SSA to date. We highlight the gaps in AAP epidemiological studies conducted in different sub-regions of SSA and provide methodological recommendations for future environmental epidemiology studies addressing AAP in the SSA region.

The accumulation of high levels of lead or lead ions in a human body is harmful, particularly to children. Its neurotoxic effect is profound, damaging the central and peripheral nervous systems, resulting in stunted growth, behavioral problems and learning disabilities. The major source of lead or lead ions comes from the drinking water and tap water. The assessment of the water quality, including lead or lead ion content, is usually completed by a regional water department professional. This assessment is time-consuming and requires expensive instruments and skilled operators. Therefore, there is a need to produce a simple-use and relatively inexpensive method to detect lead or lead ions in water samples. This research has developed a simple-use, cost effective sensor system for the detection of lead ions in tap water. An under-potential deposited bismuth sub-layer on a thin gold film based electrochemical sensor was designed, manufactured and evaluated. Differential pulse voltammetry (DPV) measurement technique was employed in this detection. Tap water from the Cleveland, Ohio, USA regional water district was the test medium. Concentrations of lead ion in the range of 8 X 10^-8 M to 8 x 10^-4 M were evaluated. This DPV detection system required 3 -6 minutes to complete the detection measurement. A longer measurement time of 6 minutes was used for the lower lead ion concentration. The selectivity of this lead ion sensor was very good, and Fe III, Cu II, Ni II and Mg II at a concentration level of 5×10^-4 M did not interfere with the lead ion measurement.

My innovative entropy measure, Ismail entropy, namely, (IE) is an ultimate generalization to numerous generalized entropies within the literature. The fractal dimension of IE is identified in this paper. On another applicative note, this paper offers some potential applications of fractal dimension to smart cities. The paper ends with closing remarks combined with some challenging open problems and the next phase of research.

Algeria, the main fire hotspot on the southern rim of the Mediterranean Basin, lacks complete fire dataset with official fire perimeters, and the existing one contains inconsistencies. Preprocessed global and regional burned area (BA) products provide valuable insights into fire patterns, characteristics and dynamics over time and space, and into their impact on climate change. Nevertheless, they exhibit certain limitations linked with their inherent spatio-temporal resolutions. To address the need for reliable BA information in Algeria, we systematically reconstructed, validated and analyzed a 40-year (1984–2023) BA product (NEALGEBA; North Eastern ALGeria Burned Area) at 30-m spatial resolution in the typical Mediterranean Ecosystems of this region, following international standards. We used Landsat data and the BA Mapping Tools (BAMTs) in the Google Earth Engine (GEE) to map BAs. The spatial validation of NEALGEBA, performed for 2017 and 2021 using independent 10-m spatial resolution Sentinel-2 reference data, showed overall accuracies > 98.10 %; commission and omission errors < 8.20 %; Dice coefficients > 91.90 %, and relative biases < 3.44 %. The temporal validation, however, using MODIS and VIIRS active fire hotspots, emphasized the limitation of Landsat-based BA products in temporal fire reporting accuracy terms. The intercomparison with five readily available BA products for 2017, by using the same validation process, demonstrated the overall outperformance of NEALGEBA. Furthermore, our BA product exhibited the highest correspondence with the ground-based BA estimates. NEALGEBA currently represents the most extensive and reliable time series of BA history at fine spatial resolution for NE Algeria, offering a significant contribution for further national and international fire hazard and impact assessments and acts as a reference dataset for contextualizing future weather extremes, such as the 2023 exceptional heat wave, which we show not to have led to the most extreme fire year over the last four decades.

Garlic, as an important economic crop in China, still has room for improvement in terms of identification using remote sensing technology, Among them, high-precision classification of garlic has become an important subject. The Erhai Lake is an important freshwater lake in China. Under the influence of technology and policies, significant changes have occurred in the cultivation of garlic crops. this study constructed multidimensional features for crop classification suitable for Google Earth Engine, and Propose a method for identifying garlic crops using sample and feature datasets under limited conditions. The results indicate that: 1) In the land-use classification of the Erhai Lake Basin, the importance ranking of characteristic bands, from high to low, is as follows: spectral features, vegetation features, texture features, and terrain features. 2) The Random Forest method based on feature selection demonstrates high classification accuracy in land-use classification within the Erhai Lake Basin in Yunnan Province. The overall classification accuracy reaches 95.79%, with a Kappa coefficient of 0.9481. 3) The expansion direction of garlic cultivation in the Erhai Lake Basin initially strengthened and then weakened from 1999 to 2023. The vertical development of garlic cultivation reached saturation, showing a slow trend towards horizontal expansion between 2005 and 2018. The planting distribution in various townships in the Erhai Lake Basin gradually shifted from a relatively uniform distribution to an upstream development in the basin. This study utilizes the Google Earth Engine (GEE) cloud computing platform and machine learning algorithms to compensate for the lack of statistical data on garlic cultivation in the Erhai Lake Basin. Simultaneously, it accurately, rapidly, and efficiently extracts planting information, demonstrating significant potential for practical applications.

This research analyses extreme precipitation events in the Huaihe River Basin in China, a densely populated region with a history of human settlements and agricultural activities. This study aims to explore the impact of extreme precipitation index changes and provide decision-making suggestions for flood early warning and agricultural development in the Huaihe River Basin. The study utilises the NEX-GDDP-CMIP6 climate models dataset and the daily value dataset (V3.0) from China's national surface weather stations to investigate temporal and spatial changes in extreme precipitation indices from 1960 to 2014 and future projections. At the same time, this study adopted the RclimDex model, Taylor diagram and Sen+Mann-Kendall trend analysis research methods to analyse the data. The results reveal a slight increase in extreme precipitation indices from northwest to southeast within the basin, except for CDD, which shows a decreasing trend. Regarding spatial, the future increase of extreme precipitation in the Huaihe River Basin will show a spatial variation characteristic that decreases from northwest to southeast. These findings suggest that extreme precipitation events are intensifying in the region. Understanding these trends and their implications is vital for adaptation strategy planning and mitigating the risks associated with extreme precipitation events in the Huaihe River Basin.

The study focuses on conducting a quantitative comparison of sea ice thickness data obtained through satellite-based remote sensing and in-situ observations in the eastern Arctic Ocean from September 2013 to September 2015 as part of the Nansen and Amundsen Basins Observational System (NABOS) program. Upward-looking sonar observations from an oceanographic mooring at the northern slope of the Laptev Sea (78°25’N, 125°04’E) were used for comparing instrumental measurements of ice thickness with data from the remotely sensed CryoSat-2 and CryoSat2/SMOS datasets. The comparison results indicate a significant tendency for satellite products to overes-timate sea ice thickness by more than 40 cm, particularly for moderate and thick ice conditions. Caution is advised when using these satellite-based measurements. Sea ice ridging is identified as one of the possible factors contributing to the observed discrepancy. The continental slope of the Laptev Sea experienced a prevalence of ridged ice over level ice during the period from 2013 to 2015. In the spring season (March-May), ridged ice was observed approximately 60% of the time, while level ice was observed around 40% of the time. However, the most significant relative contribution of ridging to ice thickness was observed during the initial ice formation period (from October through December) when sea ice is thin (<1 m). During these months, the relative difference between the mean and modal ice thickness, which reflects the mean variation between the deformed and thermodynamically grown level sea ice, could be as high as 70%.

We consider open non-twist Hamiltonian systems represented by an area-preserving two-dimensional map describing incompressible planar flows in the reference frame of a propagating wave, and possessing exits through which map orbits can escape. The corresponding escape basins have a fractal nature that can be revealed by the so-called basin entropy, a novel concept developed to quantify final-state uncertainty in dynamical systems. Since the map considered violates locally the twist condition, there is a shearless barrier that prevents global chaotic transport. In this paper we show that it is possible to determine the shearless barrier breakup by considering the variation of the escape basin entropy with a tunable parameter.

Management of Australia’s largest river system, the Murray-Darling Basin (MDB) is controversial, addressing conflicting demands from stakeholders, including irrigators, the agriculture industry, indigenous groups, and the environmental lobby. Oversight is concentrated in a single agency, the MDB Authority, but climate change and the water market have contributed to uncertainty over the Basin’s environmental sustainability. This paper reports on preliminary research in South Australia’s Riverland, one of Australia’s most important wine, citrus, nuts, and stone fruit production areas. It focuses on the Renmark Irrigation Trust (RIT), supplying water to irrigators, primarily horticulturalists. It investigates the chief risks perceived and future-plans in face of concerns over variable water flows and economic uncertainty. Using sequential mixed methods, a questionnaire survey supplied information from a sample of irrigators, covering land use, on-farm environmental actions, risks, decision making, recent and proposed changes to farm management, and attitudes to the MDB Plan and the water market. Focus groups and interviews then enabled key topics to be addressed in greater depth. The RIT’s contribution to river restoration is highlighted, with its plans for additional on-farm water stewardship investigated. There are high levels of uncertainty regarding future viability of smallholdings, including unintended consequences from the water market (e.g., increasing areas under water hungry almonds), the role of water brokers, and environmental viability of the river system linked to climate change. More optimistic voices point to increased diversity of production, resilience of the local horticultural industry, and new entrants in the form of hobby and part-time producers.

Globally, the intensity and irregularity of weather and climate extremes are increasing due to climate change. In Ethiopia, the occurrence of extreme events has been increasing, reporting severe impacts on environment which led to losses of lives and livelihood of societies. In this study, Heat Wave Magnitude Index daily (HWMId) was used to analysis heat wave magnitude in the Middle Awash Basin of Ethiopia. Gauge data obtained from Ethiopian Meteorological Institution (EMI) for 1981-2022 period and the future projection was taken from Coupled Model Intercomparison Project Phase 6 (CMIP6) under two socioeconomic pathways (SSP 2 and SSP 5) scenarios. The findings clearly showed that the area aggregated annual temperature anomaly increasing each year, 2015 was one of the warmest year on record with an anomaly of +1.8 °C. Severe to extreme heat wave recorded particularly during the last 10 years. For the future projection, under SSP 2-4.5 forcing scenario, the annual average air temperature projected to be warmer, which increasing 1.7 ℃ to 1.8 ℃ during mid-century and 2.3 ℃ to 2.4 ℃ end of century. Meanwhile, for SSP 5-8.5 forcing, the projection indicated an increment of 2.2 ℃ to 2.5 ℃ under mid-century and 4.4 ℃ to 4.8 ℃ end of century. Concerning the severity of heat wave, extreme to very extreme heat wave projected under SSP 2-4.5 forcing scenario and supper extreme heat wave projected under SSP 5-8.5 forcing scenario, respectively. The increase in extreme events may have a negative impact on health, water availability and food security. Therefore, the result of this study are essential for making wise decisions and for developing suitable strategies for climate change adaptation and mitigation that could minimize the risk of unusually extreme weather events.

Since the early 1990s, the European (ESA) and Italian (ASI) space agencies have managed and distributed a huge amount of satellite-recorded SAR data to the research community and private industries. Moreover, the availability of advanced cloud computing services implementing different multi-temporal SAR interferometry techniques allows the generation of deformation time series from massive SAR images. We exploit the information provided by a large PS dataset to determine the temporal trend of ground deformation and the relative deformation rate with millimetric accuracy to analyse the spatial and temporal distribution of land subsidence induced by water pumping from a deep confined aquifer in the Northern Valle Umbra Basin (Central Italy), exploiting 24 years of Permanent Scatterers – Interferometric SAR data archives. The SAR images were acquired between 1992 and 2016 by satellite ERS1/2, ENVISAT and Sentinel 1 ESA missions, and the COSMO-SkyMed ASI mission). We observe ground velocities and deformation geometries between 1992 and 2016, with displacements of more than 70 cm and velocities of up to 55 mm/yr and the results suggest that the shape and position of the surface ground displacement are controlled by the fault activity hidden under the valley deposits.