In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

The layered oxyselenide BiCuSeO has garnered significant interest because of its ability to exhibit low thermal conductivity and a high Seebeck coefficient. This study involved the preparation of Bi1−xNaxCuSeO1−xFx(x=0, 0.05, 0.10, 0.15, and 0.20) ceramics through the processes of high energy ball milling and cold isostatic pressing. A systematic study was conducted to investigate the impact of co−doping Na/F on the thermoelectric performance of BiCuSeO ceramics. Replacing Bi3+ with Na+ results in the introduction of a considerable amount of holes, leading to a notable enhancement in the electrical conductivity and power factor. The conductivity was significantly increased from 9.10 S cm−1 in the pure BiCuSeO to 94.5 S cm−1 in Bi0.85Na0.15CuSeO0.85F0.15 at 323 K. At 823 K, the power factor of the Bi0.85Na0.15CuSeO0.85F0.15 sample achieved 44.8×10−5 W/ m K2. Moreover, the Bi1−xNaxCuSeO1−xFx ceramics exhibit a minimum thermal conductivity of 0.43 W m−1 K−1. As a result, the Bi0.85Na0.15CuSeO0.85F0.15 sample achieves a maximum ZT value of 0.78, which is 7.09 times greater than that of the pure BiCuSeO sample (0.11) .