As semi-airborne mineral exploration has limited budgets, it is critical to design experimental procedures that generate data maximizing the desired information We investigate the effects of transmitter-receiver geometries for a variety of anomalies and semi-airborne layouts. Our simulations indicate that 200 m flight line spacing and 100 m point distance are the optimal trade-off between coverage and survey progress for various targets. Based on the target size and distance between the transmitter and the target, the transmitter length should be at least equal to the length of the target and for more than 1 km, at least two or three times the target size. Likewise important are the location and direction of the transmitter cables, which can have great impact on the result of inversion and should be parallel to the target strike. By using more than one transmitter, better results are obtained. If the strike of the target is known, transmitters should be parallel to each other and if not, it is better to use perpendicular transmitters. Results showed that the optimal distance between transmitters is 3 km. Our simulations show that it is even possible to recover targets just below the transmitter in corresponding areas of masked data.

The outbreak of COVID-19 has caused a global public health crisis. The spread of SARS-CoV-2 by contact is widely accepted, but the relative importance of aerosol transmission for the spread of COVID-19 is controversial. Here we characterize the distribution of SARA-CoV-2 in 123 aerosol samples, 63 masks, and 30 surface samples collected at various locations in Wuhan, China. The positive percentages of viral RNA included 21% of the aerosol samples from an intensive care unit and 39% of the masks from patients with a range of conditions. A viable virus was isolated from the surgical mask of one critically ill patient while all viral RNA positive aerosol samples were cultured negative. The SARS-CoV-2 detected in masks from patients, ambient air, and respirators from health workers compose a chain of emission, transport, and recipient of the virus. Our results indicate that masks are effective in protecting against the spread of viruses, and it is strongly recommended that people throughout the world wear masks to break the chain of virus transmission and thus protect themselves and others from SARS-CoV-2.

There is a lot of discussion underway with conflicting opinions examining the airborne nature of the SARS-CoV2 virus. Surprisingly, important phenomena prevalent with respect to aerosols (suspended droplets) have not been considered. In this Technical Note, we propose a methodology for the coupling of aerosol phenomena (such as evaporation, particle transport accounting for drag) to accurately establish the lifetimes of the droplets. A characteristic time analysis illustrates the time scales for evaporation and settling: for example, the characteristic time for evaporation of a 10 µm droplet is 0.036 s at a relative humidity of 25%; compared to a settling time of about 500 s. For any particle smaller than ~ 100 µm, the evaporation of the emitted or exhaled droplet has to be considered. Coupling evaporation of the droplet as it settles, we estimate the horizontal distance traversed. Trajectories of a 10 µm and 100 µm particle emitted with a typical initial velocity of release associated with coughing and sneezing indicates the greater spread in the horizontal direction when evaporation is accounted for. The life time of the 10 µm particle increases from 8.3 min to 12 hours (will be intercepted prior and the actual airborne time will then be shorter); and for a 100 µm particle from 4.9 s to 39.4 s.

The risk of lung cancer continues to elevate for both smokers and never-smokers. With the increasing morbidities and mortalities related to lung cancer, there is much interest on establishing other confounding factors that lead to lung cancer, other than smoking which is the most common cause. Some of the environmental factors have been identified as potential lung cancer causes. Therefore, the aim of this systematic review is to assess the relationship of environmental factors and lung cancer incidences by investigating various carcinogenic risks exposures that predispose an individual to lung cancer. The objective of this systematic review is thus to assess the evidence of relationship between environmental carcinogens and lung cancer incidence by systematically reviewing relevant studies. A standard criterion for the review methodology was formulated to guide the review process and data extraction. Online databases like PubMed, MEDLINE, Scopus (EMBASE), Google Scholar, Web of Science, and CINAHL were systematically searched for articles published between 2000 and 2021 that explored potential environmental carcinogens that were believed to expose occupational workers and individuals within the environment with lung cancer risks. 25 studies were eligible based on the selection criteria, and were finally included in the systematic review among which four were case-control studies, seven were cohorts, five was prospective, four were previous systematic reviews and four were systematic analysis. Chemical exposures like pesticides were analyzed for their carcinogenesis. Air pollution was also discussed with particulate and coal being the core of evidence of association with lung cancer. Second hand smoke, Asbestos, metal compounds like copper, PVC dust particles and ionizing radiations also provided evidence of environmental carcinogenesis associating to lung cancer cases.

Airborne microplastic (MP) is an emerging pollutant, still under-characterised and insufficiently understood. Detailed description of MP air pollution is crucial as it has been identified in human lungs and remote locations, highlighting atmosphere as medium of MP dispersion and transportation. The lack of standardization of methods for measuring and further monitoring of the MP pollution is an obstacle towards the assessment of health risks. Since the first recognition of MP presence in the atmosphere of Krakow in 2019, this research was conducted to further characterise and develop the methods for qualitative and quantitative analysis of airborne MP (ATR-FTIR, Pyr-GC-MS, SEM-EDS) and pre-treatment of samples.The data was gathered in seven cycles, from June 2019 to February 2020. Methods used in the study allowed the identification and analysis of the changing ratio of the different types of synthetic polymers identified in the atmospheric fallout (LDPE, Nyl-66, PE, PET, PP, PUR). Observations of interactions between MP particles and environment were made with analyses of surface changes due to the degradation. Mineral phases attached to the MPs’ surfaces, with some of the inorganic contaminants transported on these surfaces, determined to also be of anthropogenic origin.Methodology proposed in this study, allows further characterisation of MP from multiple locations to provide highly comparable data, leading to the identification of the sources of this phenomenon, as well as seasonal changes.

In this paper we present AWEbox, a Python toolbox for modeling and optimal control of multi-aircraft systems for airborne wind energy (AWE). AWEbox provides an implementation of optimization-friendly multi-aircraft AWE dynamics for a wide range of system architectures and modeling options. It automatically formulates typical AWE optimal control problems based on these models, and finds a numerical solution in a reliable and efficient fashion. To obtain a high level of reliability and efficiency, the toolbox implements different homotopy methods for initial guess refinement. The first type of methods produces a feasible initial guess from an analytic initial guess based on user-provided parameters. The second type implements a warmstart procedure for parametric sweeps. We investigate the software performance in two different case studies. In the first case study we solve a single-aircraft reference problem for a large number of different initial guesses. The homotopy methods reduce the expected computation time by a factor of 1.7 and and the peak computation time by a factor of 8, compared to when no homotopy is applied. Overall, the CPU timings are competitive to timings reported in the literature. When the user initialization draws on expert a priori knowledge, homotopies do not increase expected performance, but the peak CPU time is still reduced by a factor of 5.5. In the second case study, a power curve for a dual-aircraft lift-mode AWE system is computed using the two different homotopy types for initial guess refinement. On average, the second homotopy type, which is tailored for parametric sweeps, outperforms the first type in terms of CPU time by a factor of 3. In conclusion, AWEbox provides an open-source implementation of efficient and reliable optimal control methods that both control experts and non-expert AWE developers can benefit from.

Evidence for the potential for airborne transmission of SARS-CoV-19 continues to accumulate, with important implications for healthcare workers, as well as the general public. Three lines of evidence support this conclusion.

A time integration scheme based on semi-Lagrangian advection and Laplace transform adjustment has been implemented in a baroclinic primitive equation model. The semi-Lagrangian scheme makes it possible to use large time steps. However, errors arising from the semi-implicit scheme increase with the time step size. In contrast, the errors using the Laplace transform adjustment remain relatively small for typical time steps used with semi-Lagrangian advection. Numerical experiments confirm the superior performance of the Laplace transform scheme relative to the semi-implicit reference model. The algorithmic complexity of the scheme is comparable to the reference model, making it computationally competitive, and indicating its potential for integrating weather and climate prediction models.

Asthma is a heterogeneous and very complex group of diseases, which includes different clinical phenotypes depending on symptoms, progression, exacerbation pattern or response to treatment among other characteristics. The allergic phenotype is the most frequent, especially in pediatric asthma. It is characterized by sensitization (production of specific IgE) to allergens, and frequent comorbidity with rhinitis and atopic dermatitis. An allergen is a substance that triggers the production of specific IgE antibodies in susceptible individuals, who present symptoms that will depend on the type and intensity of the allergenic load and the tissue where the interaction occurs. Airborne allergens cause their effects in the respiratory tract and eyes, and can be indoor or outdoor, perennial or seasonal. Although allergens such as mites, pollens or animal dander are generally considered as a single particle, it is important to note that they contain different molecules which could trigger distinct specific IgE molecules on different patients.The key points that a physician who treats asthma should be aware of are:

Airborne virus, such as COVID-19, caused pandemics all over the world. Virus-containing particles produced by infected individuals are suspended in the air for extended periods of time, actually results in viral aerosols and the spread of infectious diseases. Aerosol collection and detection devices are essential for limiting the spread of airborne virus diseases. This review provides an overview of the primary mechanisms and enhancement techniques for collecting and detecting airborne viruses. Indoor virus detection strategies for scenarios with varying ventilations are also summarized based on the excellent performance of existing advanced comprehensive devices. This review provides guidance for the development of future aerosol detection devices and aids in the control of airborne transmission diseases, such as COVID-19, monkeypox, and other airborne transmission viruses.

Mapping and prediction of inundated areas is increasingly important for climate change adaptation and emergency preparedness. Flood forecasting tools and flood risk models have to be compared to observed flooding patterns for training, calibration, validation and benchmarking. At regional to continental scale, satellite earth observation is the established method for surface water extent (SWE) mapping and several operational global-scale data products are available. However, the spatial resolution of satellite-derived SWE maps remains a limiting factor, especially in low-lying areas with complex hydrography, such as Denmark. We collected thermal imagery using an unmanned airborne system (UAS) for three areas in Denmark shortly after major flooding events. We combined the thermal imagery with an airborne lidar-derived high-resolution digital surface model of the country to retrieve high-resolution (40 cm) SWE maps. The resulting SWE maps were compared to low-resolution SWE maps derived from satellite earth observation (EO). We conclude that UAS have significant potential for SWE mapping at intermediate scales, can bridge the scale gap between ground observations and satellite EO and can be used to benchmark and validate SWE mapping products derived from satellite EO as well as models predicting inundation.

Coastal urbanisation is a widespread phenomenon throughout the world and is often linked to increased erosion. Small Pacific islands are not spared from this issue, which is of great importance in the context of climate change. The French Polynesian island of Bora Bora was used as a case study to investigate the historical evolution of its coastline classification and position from 1955 to 2019. A time series of very-high-resolution aerial imagery was processed to highlight the changes of the island’s coastline. The overall length of natural shores, including beaches, decreased by 46% from 1955 to 2019 while man-made shores such as seawalls increased by 476%, and as of 2019 represented 61% of the coastline. This evolution alters sedimentary processes: the time series of aerial images highlights increased erosion in the vicinity of seawalls and embankments, leading to the incremental need to construct additional walls. In addition, the gradual removal of natural shoreline types modifies landscapes and may negatively impact marine biodiversity. Through documenting coastal changes on Bora Bora through time, this study highlights the impacts of man-made structures on erosional processes and underscores the need for sustainable coastal management plans in French Polynesia.

Exploring the effect of the sample size on the estimation accuracy of airborne LiDAR forest attributes in a large-scale area can help in optimizing the technical application scheme of operational ALS-based large-scale forest stand inventories. In our study, sample datasets composed of different sample plots were constructed by repeated sampling from 1003 sample plots in a subtropical study area covering 2376 × 103 km2. Sixteen multiplicative power models were built in each forest type consisting of four forest attributes. Through these models, the variations of standard deviation (SD) and coefficient of variation (CV) of R2 and rRMSE of forest attribute estimation models for different quantity levels of sample plots were also analyzed. The results showed that, first, when the sample size increased from 30 to the top limit, the SD of the forest attributes and LiDAR variables showed a decreasing trend. Second, as the sample size increased, the rRMSE of the 16 forest attribute estimation models gradually decreased, while the R2 gradually increased. Third, when the sample size was small, both the SD of R2 and rRMSE of the models were large, and the SD of R2 and rRMSE gradually decreased as the sample size increased. In 50 models conducted for each attribute at the same sample size, for the mean standard deviations of forest attributes, the ten best performing models were lower than those of the total 50 models, and the worst ten models were the opposite. When the sample size increased, the accuracy of each forest attribute estimation model for each forest type gradually improved. The variation of forest attributes and the LiDAR variable of the construction model are critical factors that affect the model’s accuracy. To efficiently apply airborne LiDAR in order to survey large-scale subtropical forest resources, the sample size of the Chinese fir forest, pine forest, eucalyptus forest, and broad-leaved forest should be 110, 80, 85, and 70, respectively.

Emergence of zoonotic-human pathogens is proven to be a lethal threat to public health, and RNA virus including influenza viruses, severe acute respiratory syndrome coronavirus, middle east respiratory syndrome coronavirus, Wuhan coronavirus (COVID-19), plays a pivotal role. As those viruses as airborne microorganisms spread mainly by tiny airborne particles, it is important to de-active those airborne particles before their entry into human bodies. In this study, we investigated the effect of far infrared (FIR) radiation on inhibition of airborne microorganisms. The result confirmed that double stand DNA from airborne microorganisms were stable under mild FIR radiation. However, single strand RNA from them was found to be sensitive to FIR radiation, indicating that RNA virus in airborne particles is instable under FIR radiation. Based on this observation, two models on usage of FIR radiation to prevent RNA virus transmission and cure RNA virus infection were proposed, implying that FIR radiation might be a cheap, convenient, and efficient method in clinic to treat RNA virus.

Repeated single-point measurements of thoracic bioimpedance at single (low)-frequency are strongly related to fluid changes during hemodialysis. Extension to semi-continuous measurements may provide longitudinal details in the time pattern of the bioimpedance signal, and multifrequency measurements may add in-depth information on the distribution between intra- and extracellular fluid. This study aims to investigate the feasibility of semi-continuous multifrequency thoracic bioimpedance measurements by a wearable device in hemodialysis patients. Therefore, thoracic bioimpedance was recorded semi-continuously (i.e. every ten minutes) at nine frequencies (8 – 160 kHz) in 68 patients during two consecutive hemodialysis sessions, complemented by a single-point measurement at home in-between both sessions. On average, the resistance signals increased during both hemodialysis sessions and decreased during the interdialytic interval. The increase during dialysis was larger at 8 kHz (∆ 32.6 Ω during session 1 and ∆ 10 Ω during session 2) compared to 160 kHz (∆ 29.5 Ω during session 1 and ∆ 5.1 Ω during session 2). Whereas the resistance at 8 kHz showed a linear time pattern, the evolution of the resistance at 160 kHz was significantly different [p < 0.0001]. Measuring bioimpedance semi-continuously and with a multifrequency current is a major step forward in the understanding of fluid dynamics in hemodialysis patients. This study paves the road towards remote fluid monitoring.

There has been a surge in the interest for (semi)transparent photovoltaics (sTPVs) in recent years, since the more traditional, opaque, devices are not ideally suited for a variety of innovative appli-cations spanning from smart and self-powered windows for buildings to those for vehicle inte-gration. Additional requirements for these photovoltaic applications are a high conversion effi-ciency (despite the necessary compromise to achieve a degree of transparency) and an aesthetical-ly pleasing design. One potential realm to explore in the attempt to meet such challenges is the bio-logical world, where evolution has led to highly efficient and fascinating light-management structures. In this mini-review, we explore some of the biomimetic approaches that can be used to improve both transparent and semitransparent photovoltaic cells, such as moth-eye inspired structures for improved performance and stability or tuneable, coloured, and semi-transparent devices inspired by beetles’ cuticles. Lastly, we will briefly discuss possible future developments for bio-inspired and potentially bio-compatible sTPVs.

Since the beginning of coronavirus disease 2019 (COVID-19) pandemic, large attention has been focused on the relationship between SARS-CoV-2 diffusion and environment. As a matter of fact, clear evidence of the transmission of SARS-CoV-2 via respiratory aerosol would be of primary importance; at the same time, checking the presence of SARS-CoV-2 in wastewater can be extremely useful to control the diffusion of the disease. Up to now, many studies report SARS-CoV-2 concentrations in indoor/outdoor air samples or water/wastewater samples that can differ by order of magnitude. Unfortunately, complete information about the scientific approach of many studies is still missing, relating to: samplers and sampling materials performances, recovery tests, measurement uncertainty, robustness, detection and quantification limits, infectivity of captured virus, virus degradation during sampling, influence of sample pre-treatments (included freezing) on results, effects of inhibitors, sample alterations due to manipulation, validation of methods and processes, quality assurance according to ISO/IEC 17025 requirements.Based on the first experiences focused on the presence of SARS-CoV-2 in environmental samples such as air quality filters, air-liquid impingers and wastewater samples, the present study describes a coherent preliminary approach to SARS-CoV-2 environmental sampling in order to overcome the evident lack of standardization. Three aspects are highlighted here: the first solution to assure quality and consistency to environmental sampling relies on the development of recovery tests using standard materials and investigating sampling materials, sampling techniques, sampling durations, sample conservation and pre-treatments; secondly, in order to overcome the shortcomings of every single sampling technique, coupling different samplers in parallel sampling could be an efficient strategy to collect more information and make data more reliable, in particular for air samples; finally, with regards to airborne virus sampling, the results could be confirmed by simplified emission and dilution models.

The mass concentration of particulate matter (PM) has been systematically used in epidemiological studies as exposure indicator, to relate airborne concentrations with a wide variety of human health effects, which can be hardly explained by using this single parameter. In fact, PM is a “particle cocktail” that includes a complex mixture of compounds with a wide range of sizes, chemical compositions and emission sources. Current research hypothesizes that many of the adverse health effects are derived from oxidative stress in biological systems caused by the deposition of PM into the lungs. This emerging hypothesis is called the oxidative stress paradigm. In this commentary article we analize how this new paradigm could help to answer the as-of-yet unanswered questions related to the mechanism of action of PM pollution on human health. Acellular oxidative potential (OP) assays have been emerged as a promising approach to quantify the PM potential to induce oxidative stress and to relate it with the chemical composition and size distribution of PM. Recent researches have shown that the OP is related to the presence of metals, organic carbon, polyaromatic hydrocarbons and quinones. However, the association between PM and particle-induced toxicity is still largely unknown. Therefore, additional research is needed to identify the specific PM characteristic(s), such as its specific size, emission source or chemical content, which contribute the most to its redox activity. Thus, the OP measurements provide information that allows us to evaluate and integrate the toxic potential of PM in a unique parameter, whose relationships with emission sources, size distribution and/or chemical composition should be faced in the near future.

Multi-object tracking (MOT) in airborne videos is a challenging problem due to the uncertain airborne vehicle motion, vibrations of the mounted camera, unreliable detections, size, appearance and motion of the moving objects as well as occlusions due to the interaction between the moving objects and with other static objects in the scene.To deal with these problems, this work proposes a four-stage Hierarchical Association framework for multiple object Tracking in Airborne video (HATA). The proposed framework combines data association-based tracking (DAT) methods and target tracking using a Compressive Tracking approach, to robustly track objects in complex airborne surveillance scenes. In each association stage, different sets of tracklets and detections are associated to efficiently handle local tracklet generation, local trajectory construction, global drifting tracklet correction and global fragmented tracklet linking. Experiments with challenging airborne video datasets show significant tracking improvement compared to existing state-of-art methods.

Laser scanning systems make use of Light Detection and Ranging (LiDAR) technology to acquire accurately georeferenced sets of dense 3D point cloud data. The information acquired using these systems produces better knowledge about the terrain objects which are inherently 3D in nature. The LiDAR data acquired from mobile, airborne or terrestrial platforms provides several benefit over conventional sources of data acquisition in terms of accuracy, resolution and attributes. However, the large volume and scale of LiDAR data have inhibited the development of automated feature extraction algorithms due to the extensive computational cost involved in it. Moreover, the heterogeneously distributed point cloud, which represents objects with varying size, point density, holes and complicated structures pose a great challenge for data processing. Currently, geospatial database systems do not provide a robust solution for efficient storage and accessibility of raw data in a way that data processing could be applied based on optimal spatial extent. In this paper, we present Global LiDAR and Imagery Mobile Processing Spatial Environment (GLIMPSE) system that provides a framework for storage, management and integration of 3D LiDAR data acquired from multiple platforms. The system facilitates an efficient accessibility to the raw dataset, which is hierarchically represented in a geographically meaningful way. We utilise the GLIMPSE system to automatically extract road median from Airborne Laser Scanning (ALS) point cloud. In the first part of this paper, we detail an approach to efficiently retrieve the point cloud data from the GLIMPSE system for a particular geographic area based on user requirements. In the second part, we present an algorithm to automatically extract road median from the retrieved LiDAR data. The developed road median extraction algorithm utilises the LiDAR elevation and intensity attributes to distinguish the median from the road surface. We successfully tested our algorithms on two road sections consisting of distinct road median types based on concrete and grass-hedge barriers. The use of GLIMPSE improved the efficiency of the road median extraction in terms of fast accessibility to ALS point cloud data for the required road sections. The developed system and its associated algorithms provide a comprehensive solution to the user's requirement for an efficient storage, integration, retrieval and processing of large volumes of LiDAR point cloud data. These findings and knowledge contribute to a more rapid, cost-effective and comprehensive approach to surveying road networks.

Real and complex analytic functions are largely studied in the field of complex analysis and are seen as very useful tools in solving problems in mathematics, physics and engineering. Real and complex numbers are a subset of semi-structured complex numbers (a new number set created to algebraically solve division by zero). Nevertheless, the properties of analytic functions made up of semi-structured complex variables (called semi-structured complex analytic functions) is yet to be explored. This limits the range of possible problems that can be resolved using analytic functions). In this regard, the aim of this paper was to expound upon the properties of semi-structured complex analytic functions and show their application in solving engineering problems. The results of this paper included (1) developing a full set of Cauchy–Riemann Equations for the semi-structured complex -space; (2) define sufficient and necessary conditions for a semi-structured complex function to be analytic; (3) determine the relationship between semi-structured complex analytic functions, Laplace’s Equations and Poisson’s Equations; and (5) provide an example of the use of these functions.

A study was carried out in a Waste Sorting Plant (WSP) located in France and treating dry recyclable household waste (DRHW) as well as dry recyclable commercial and industrial waste (DRCIW). The aim was to investigate the exposure to bioaerosol and dust. The aim of the study was to assess the extent to which the measurement of concentration, species composition and particle size distribution can contribute to a better assessment of the biological risks associated with exposure. Both stationary and personal bioaerosol and dust samples were collect in the (WSP). The results confirm that waste and waste sorting activities are sources of airborne fungi. Indeed, ambient concentrations ranged from 7.3×103 to 8.5×105 CFU/m3 for culturable moulds and up to up to 4 mg/m3 for dust. Personal exposure to inhalable dust was found up to 3 mg/m3 for dust and ranged from 8.6×103 to 1.5×106 CFU/m3 for fungi. Airborne fungal communities were found to be dominated by the Penicillium genera in both bioaerosols and settled dust samples, followed by the Aspergillus, Cladosporium, Wallemia, Mucor, and Rhizopus genera. Fungi were carried by particles of aerodynamic diameters mainly between around 2.0 and 10.0 µm. The findings dealing with size distribution and biodiversity of bioaerosols suggest that employees are exposed to complex bioaerosols during their work and helps to make a finer diagnosis of the risks involved, which is often difficult in the absence of any OEL for bioaerosols in general.

The pollution caused by nitrogen dioxide is a major environmental problem in China. This study introduces a new type of atmospheric trace gas remote-sensing instrument, an airborne fiber imaging spectrometer. This spectrometer has a spectral range of 300–410 nm and works in push-broom mode with a 30° field of view on a flight path. Flight experiments were conducted on December 30, 2022 and January 5, 2023, covering heavily polluted areas of east of Beijing and Tangshan. This equipment obtained the density distribution of NO2 over the flight area. The results showed that pollution was mainly concentrated in the Caofeidian area and at the power station in the north, and the main source of pollution was anthropogenic. Satellite and airborne data near the pollution points were compared, and the two datasets showed a positive correlation with a correlation coefficient of 0.78 and 0.7, on the two days, respectively. This study demonstrates the capability of an airborne fiber imaging spectrometer for NO2 regional emission remote sensing and identifying the pollution points.

Iron (Fe), the main component of non-exhaust particulates, is known to have variable health effects that depend on the chemical species of iron. This study characterized the possible contribution of iron oxides and hydroxides to airborne brake-wear particles under realistic vehicle driving and braking conditions with different brake-pad friction materials. We found significant differences in wear coefficients and PM₁₀ emissions between non-asbestos organics (NAO) and European performance (ECE) brake pads. Iron was the dominant contributor to PM₁₀ and PM_2.5 brake-wear particles for both NAO and ECE. The iron concentration ratio in the particle mass were comparable to the disc to pads ratio measured by wear mass. The fact that magnetite, which is of interest with respect to health effects, was less abundant in NAO than in ECE suggested that tribo-oxidations occurred in NAO. Metallic iron is generated not only from abrasive wear but also from tribo-chemical reduction with magnetite as the starting material. We found differences not only in PM emissions between brake friction materials but also that the phase transformations of iron differed between friction materials. These differences were apparent in the distribution of iron oxides and hydroxides. Heat, tribo-oxidation, and tribo-reduction are intricately involved in these reactions.

This study is describing airborne geophysical survey, carried out in Northeastern Russia (Archangelsk region) in order to aimed at geological mapping of Grib kimberlite pipe, which is known to have strong presence of remanent magnetization. Airborne data were inverted using two techniques, the magnetization vector inversion (MVI) and a QDIK inversion, a proprietary algorithm developed at the Irkutsk State University (ISTU), which allows extracting four parameters from airborne magnetic data (magnetic susceptibility, inclination, declination and Koeniksberger ratio). The inversion results were further analyzed and verified against the known geology of the Grib kimberlite. The study allowed to better map geology of Grib kimberlite using only uninvasive (remote sensing) technology

Climate change and exposure to environmental pollutants play a key role in the onset and aggravation of allergic diseases. As different climate-dependent patterns of molecular immunoglobulin E (IgE) reactivity have been regionally described, we sought to investigate the evolving allergen exposome in distinctive allergic phenotypes, and subtropical weather conditions through a Precision Allergy Molecular Diagnosis (PAMD@) model. Concurrent sensitization to several house dust mites (HDM) and storage mite molecules were broadly dominant in the investigated cohort, followed by the major cat allergen Fel d 1, and regardless of the basal allergic disease. Although a complex repertoire of allergens was recognized, a steadily increasing number of IgE binding molecules was associated with the complexity of the underlying atopic disease. Besides the highly prevalent IgE responses to HMD major allergens, Der p 21, Der p 5, and Der p 7 also showed as serodominant molecules, especially in those subjects bothered with asthma and atopic dermatitis. The accurate characterization of the external exposome at the molecular level and their putative role as clinically relevant allergens is essential to elucidate the phenotypic diversity of atopic disease in terms of personalized diagnosis and therapy.

Airborne wind energy (AWE) systems use tethered flying devices to harvest higher-altitude winds to produce electricity. For a successful deployment of these systems, it is crucial to understand how the public perceives them. If public concerns about the technology are not taken seriously, implementation could be delayed or, in some cases, prevented, resulting in increased costs for project developers and a lower contribution of the sector to renewable energy targets. This literature review assessed the current state of knowledge on public responses to AWE. An exhaustive literature search led to the identification of 40 relevant publications that were reviewed. The literature assumed that the safety, visibility, acoustic emissions, ecological impacts, and the siting of AWE systems shape public responses to the technology. The reviewed literature views people’s responses to AWE very optimistically but lacks scientific evidence to back up its claims. It seems to overlook that the influence of AWE’s characteristics (e.g., visibility) on public responses will also depend on a range of situational and psychological factors (e.g., people’s general attitude towards AWE, the public’s trust in project developers). Therefore, empirical social scientific research is needed to increase the field’s understanding of public responses to AWE and thereby facilitate deployment.

From a scientific standpoint, both temporal and spatial variables must be examined when developing programs for training various soccer scoring techniques (SSTs), but a review of current literature reveals that existing scientific studies have overlooked this combinatory influence. Consequently, there is no reliable theory on temporal-spatial identification when evaluating scoring opportunities. Quantified by using biomechanical modeling, anthropometry, and SSTs found in FIFA Puskás Award (121 nominated goals between 2009 and 2020), it is found that players’ proprioceptive/effective shooting volume (i.e. players’ attack space) could be sevenfold the currently-practiced shooting volume. The ignorance of some SSTs’ training leads to the underuse of the potential shooting volume. These overlooked SSTs are airborne and/or acrobatic techniques, perceived as high-risk and low-reward. Relying on the talent of an athlete to improvise on the fly can hardly be considered as a viable coaching strategy. Therefore, for developing science-based SST training regimes, groundbreaking studies are needed to: 1) expand the perception of shooting volume, and 2) entrain one-touch-shot techniques (airborne/acrobatic) within this volume, in short, Focusing-on-Time-in-Space. Whence, the new temporal-spatial theory could guide future researches and develop novel training programs. An increase of airborne/acrobatic goals would ultimately further enhance the excitement of the game.

This paper presents a comparison between a kite model with a constant-length tether and a model based on a system identification algorithm. The concept of system identification is applied to predict the uncertainties related to the variation of the wind speed and the shape deformation of the tethered membrane wing during flight. A pole-placement controller is used to ensure that the kite follows the planned flight path. Thus, we can determine the required locations of the closed loop poles, and then enforce them by changing the controller's gains in real-time. The capability of the system identification algorithm to recognize sudden changes in the dynamic model, and the ability of the controller to stabilize the system in the presence of such changes are confirmed. Furthermore, the system identification algorithm is applied to determine the parameters of a kite with variable-length tether used in a flight test of the 20 kW kite power system of TU Delft. Experimental data of this test were compared with the system identification results in real-time and significant changes were observed in the parameters of the dynamic model which heavily affect the resulting response.

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.

Drought is a powerful natural hazard that has significant effects on ecosystems amid the constant threats posed by climate change. This study investigates agricultural drought in a semi-arid Mediterranean basin through the interconnections of four indices: precipitation (meteorological reanalysis), vegetation development, thermal stress, and soil water deficit (remote sensing observations). The study focuses on the determination of agricultural drought periods. Firstly, the temporal connections between the various indices at different spatial scales and in different parts of the basin are investigated. Thereafter, a modified run-theory approach based on normality and dryness thresholds is applied. The Pearson correlations at different spatial scales showed a medium to low level of agreement between the indices, which was explained by the geographical heterogeneity and the climatic variability between the agrosystems within the basin. It is also shown that the cascade of impacts expected from lower precipitations is revealed by the cross-correlation analysis. The connection between precipitation deficit and vegetation remains significant for at least one month for most pairs of indices, especially during drought events, suggesting that agricultural drought spells can be connected in time through the three or four selected indices. Short-, mid-, and long-term impacts of precipitation deficiencies on soil moisture, vegetation, and temperature were revealed. As expected, the more instantaneous variables of soil moisture and surface temperature showed no lag with precipitation. Vegetation anomalies at the monthly time step showed a two-month lag with a preceding effect of vegetation to precipitation. Finally, the determination of drought events and stages with varying thresholds on the run-theory showed the large variability of duration, magnitude, and intensity according to the choice of both normality and dryness thresholds.

Because of the near-term risk of extreme weather events and other adverse consequences from climate change, and, at least in the longer term, global fossil fuel depletion, there is world-wide interest in shifting to noncarbon energy sources, especially renewable energy (RE). Because of possible limitations on conventional renewable energy sources, researchers have looked for ways of overcoming these shortcomings by introducing radically new energy technologies. The largest RE source today is bioenergy, while solar energy and wind energy are regarded as having the largest technical potential. This paper reviews the literature on proposed new technologies for each of these three RE sources: microalgae for bioenergy, photolysis and airborne wind turbines. The main finding is that their proponents have underestimated the difficulties facing their introduction on a very large scale.

In airborne sensor networks (ASNs), the media access control (MAC) protocol is facing with serious unfairness problem due to the traditional protection mechanism of air-to-air communications among aircrafts. Actually by using the binary exponential back-off algorithm at high traffic loads to minimize collisions among users, the latest successful node can always benefit from this kind of MAC to obtain channel resources. Moreover, when taking the existence of the hidden nodes in ASNs into account, the inaccurate traffic load information will further aggravate the system’s unfairness. In this paper, a neighbor-channel-aware (NCA) protocol is proposed to improve the fairness of MAC protocol in ASNs. In the proposal, the NCA frame is firstly added and exchanged between neighbor nodes periodically, which helps to resolve the inaccurate traffic load information, so as to avoid reducing the probability of successful message transmission. Then a traffic-loading based back-off algorithm is involved to make the neighbor nodes cooperatively adjust the inter-frame space (IFS) interval to further reduce the unfairness. The simulation results show that, the proposed MAC protocol can guarantee the satisfied fairness, simultaneously avoiding heavy network overloads to protect key messages’ successful transmissions in ASNs.

Knowledge about the genesis and evolution of black soils in the Eastern Mediterranean is vital for sustainable land management. In this study, the black soils that currently occur in the Eastern Mediterranean were analyzed in different bioclimatic zones and were found to genetically be long to three soil types: 1-Calcareous black soils (Rendzina, Para-Rendzina) (Rendzic or Somerirendzic Leptosols -Typic Rendolls or Lithic Rendolls), 2-Hydromorphic black soils (Calcic Chernozems -Haploxerolls). 3- Black soils on Basalt (Somerirendzic Leptosols) (Haploxerolls). The impact of the relief was obvious on both the thickness of the solum and the mollic horizon. Rendzina occurs on the toe and feet slope, Para-Rendzina on the shoulders, and Chernozems on a flat plain. The color of the epipedon in Rendzina reflects the origin of the prevailing parent material from which they are derived: Proper Rendzina found on limestone, chalk, sandstone, conglomerate, and claystone; Reddish Rendzina on Dolomite and hard limestone, and Grayish Rendzina on Serpentine. It was also found that the Hydromorphic black soils only occur on calcic marl and lacustrine deposits in the depressions arising from the Dead Sea faults under saturation or bad drainage conditions. This soil has a thick, dark mollic horizon and high organic matter content.

Complex models have received significant interest in recent years and are being increasingly used to explain the stochastic phenomenon with upward and downward fluctuation such as the stock market. Different from existing semi-variance methods in traditional integer dimension construction for two variables, this paper proposes a simplified multi-factorized fractional dimension derivation with the exact Excel tool algorithm involving the fractional center moment extension to covariance, which is a complex parameter average that is a multi-factorized extension to Pearson covariance. By examining the peaks and troughs of gold price averages, the proposed algorithm provides more insight into revealing underlying stock market trends to see who is the financial market leader during good economic times. The calculation results demonstrate that the complex covariance is able to distinguish subtle differences among stock market performances and gold prices for the same field that the two variable covariance may overlook. We take the London, Tokyo, Shanghai, Toronto and Nasdaq as the representative examples.

The conversion of CO2 into more synthetically flexible CO is an effective and potential method for CO2 remediation, utilization and carbon emission reduction. In this paper, the reaction of carbon-carbon dioxide (Boudouard reaction) was performed in a microwave fixed bed reactor using semi-coke (SC) as both the microwave absorber and reactant and was systematically compared with that heated in a conventional thermal field. The effects of the heating source, SC particle size, CO2 flow rate and additives on CO2 conversion and CO output were investigated. By microwave heating (MWH), CO2 conversion reached more than 99 %, while by conventional heating (CH), the maximum conversion of CO2 was approximately 29% at 900 °C. Meanwhile, for the reaction with 5 wt% Barium Carbonate added as a promoter, the reaction temperature was significantly reduced to 750 °C with almost quantitative conversion of CO2. Further kinetic calculations showed that the apparent activation energy of the reaction under microwave heating was 46.3 kJ/mol, which was only one-third of that observed under conventional heating. The microwave-assisted Boudouard reaction with catalytic barium carbonate is a promising method for carbon dioxide utilization.

Complete digraphs are referred to in the combinatorics literature as tournaments. We consider a family of semi-simplicial complexes, that we refer to as ``tournaplexes'', whose simplices are tournaments. In particular, given a digraph G, we associate with it a ``flag tournaplex'' which is a tournaplex containing the directed flag complex of G, but also the geometric realisation of cliques that are not directed. We define several types of filtrations on tournaplexes, and exploiting persistent homology, we observe that flag tournaplexes provide finer means of distinguishing graph dynamics than the directed flag complex. We then demonstrate the power of these ideas by applying them to graph data arising from the Blue Brain Project's digital reconstruction of a rat's neocortex.

This study evaluated the impact of climate change on water resources in a large semi-arid urban watershed located in Niamey Republic of Niger, West Africa. The watershed was modeled using the fully integrated surface-subsurface HydroGeoSpheremodel at a high spatial resolution. Historical (1980-2005) and projected (2020-2050) climate scenario derived from the outputs of three Regional Climate Models (RCM) under the RCP 4.5 scenario were statistically downscaled using the multiscale quantile mapping bias correction method. Results show that the bias correction method is optimum at daily and monthly scales, and increased RCM resolution does not improve the performance of the model. The three RCMs predict increases of up to 1.6% in annual rainfall and of 1.58°C for mean annual temperatures between the historical and projected periods. The durations of the Minimum Environmental Flow (MEF) conditions, required to supply drinking and agriculture water, were found to be sensitive to changes in runoff resulting from climate change. MEF occurrences and durations are likely to be greater for (2020-2030), and then they will be reduced for (2030-2050). All three RCMs consistently project a rise in groundwater table of more than 10 meters in topographically high zones where the groundwater table is deep and an increase of 2 meters in the shallow groundwater table.

Soil salinity, whether natural or human induced, is a major geo-hazard in arid and semi-arid landscapes. In agricultural lands, it negatively affects plant growth, crop yields, whereas in semi-arid and arid non-agricultural areas it affects urban structures due to subsidence, corrosion and ground water quality, leading to further soil erosion and land degradation Accurately mapping soil salinity through remote sensing techniques has been an active area of research in the past few decades particularly for agricultural lands. Most of this research has focused on the utilization and development of salinity indices for properly mapping and identifying saline agricultural soils. This research study develops a soil salinity index and model using Landsat 8 OLI image data from the near infra-red and shortwave infra-red spectral information with emphasis on soil salinity mapping and assessment in non-agricultural desert arid and semi-arid surfaces. The developed index when integrated into a semi-empirical model outperformed in its soil salinity mapping overall accuracy (60%) in comparison to other salinity indices (~50%). The newly developed index further outperformed other indices in its accuracy in mapping and identifying high saline soils (67%) and excessively high saline soils (90%).

This study aimed to investigate the possibility of using one-shot hyperspectral airborne images to recognize crops for an area with many small plots. The results showed that unsupervised clustering methods could classify crops with an accuracy of 80%, which improved to 90% when restricted to only grain crops, using a single airborne hyperspectral recording. However, additional layers such as NDVI, DTM, slope, and aspect did not improve classification accuracy. For comparison, the accuracy of clustering time series Sentinel-2 images with NDVI layers and DTM-derived data yielded an accuracy of: 74% ,Sentinel-2 time series 68% and single one registration before harvest - 39%. The results of the random forest classification were slightly less accurate due to a lack of sufficient reference data. However, it is challenging to verify the reported accuracy of crop recognition in the literature above 90% due to differences in analysis methodologies, reference data selection, pixel/object approaches, metric choice, and calculation formulas used.

Leishmaniasis in wild canids is a vector-borne disease caused in Europe by the protozoan parasite Leishmania infantum. To date, there is limited information on clinical signs and laboratory abnormalities in wolves due to leishmaniasis. The current clinical case report described a female Iberian wolf (Canis lupus signatus) housed in semi-captivity conditions at the Centro del Lobo Ibérico “Félix Rodríguez de la Fuente”, in Robledo de Sanabria, Zamora (Spain) with an interdigital ulcerous wound at the right forepaw, hyper-gammaglobulinemia, and abnormal liver blood parameters. Definitive serodiagnosis of leishmaniasis was established using antileishmanial serum antibodies and PCR analysis of different biological samples. A gold standard anti-L. infantum treatment protocol consisting in intramuscular meglumine antimoniate and oral allopurinol combination was installed. However, the presence of pain at the site of injection due to meglumine antimoniate administration forced its substitution by oral miltefosine. A progressive reduction of the levels of anti-L. infantum serum antibodies and the concentrations of gamma-globulin fraction was detected after antileishmanial treatment as well as a decline of liver GPT. To our knowledge, this is the first case of leishmaniasis diagnosed in a wolf housed in semi-captivity conditions treated and successfully cured.

Hypertensive disorders of pregnancy (HDP), including preeclampsia (PE) and gestational hypertension (GH), are major causes of maternal and fetal morbidity and mortality. This review elucidates the role of regulatory T cells (Tregs) in the immunological aspects of HDP and explores their therapeutic potential. Tregs, known for maintaining immune tolerance, are crucial in pregnancy to prevent immune-mediated rejection of the fetus. In HDP, Treg numbers and function imbalance are observed, correlating with disease severity. The review highlights that Tregs contribute to immunological adaptation in normal pregnancy, ensuring fetal acceptance and placental development. In contrast, HDP is associated with Treg dysfunction, marked by decreased numbers and impaired regulatory capacity, leading to inadequate immune tolerance and abnormal placental development. This dysfunction is particularly evident in PE, where Tregs fail to adequately modulate the maternal immune response against fetal antigens, contributing to the pathophysiology of the disorder. Therapeutic interventions aiming to modulate Treg activity represent a promising avenue for HDP management. Studies in animal models and limited clinical trials suggest that enhancing Treg functionality could mitigate HDP symptoms and improve pregnancy outcomes. However, the review acknowledges the complexity of translating these findings into effective clinical therapies, given the multifactorial nature of HDP and the intricate regulatory mechanisms of Tregs. In conclusion, while the precise role of Tregs in HDP is still being unravelled, their central role in immune regulation during pregnancy is indisputable. Further research is needed to fully understand the mechanisms by which Tregs contribute to HDP and to develop targeted therapies that can safely and effectively harness their regulatory potential for treating hypertensive diseases of pregnancy.

.(1) Background: Groundwater resources management in dry lands, characterized by climate var-iability and population growth, is difficult. Exploration and exploitation of groundwater, due to inadequate surface water is very costly. The present study employed Analytic Hierarchy Process (AHP) and GIS to identify Ground-Water Potential (GWP) areas in a semi-arid region of Nigeria; (2) Methods: Land-use-land-cover, drainage density, slope, rainfall, static water level, soil media, vadose media and aquifer media were selected for GWP analysis. Parameters weights were de-termined using AHP and ranked based on their contribution to GWP by experts. The parameters were then integrated using weighted overlay tool in ArcGIS 10.5 to produce GWP map of the study area. Boreholes yield data from 245 wells were collected to determine the model accuracy and model validation; (3) Results: Results classified the study area into very high GWP (1.9%), high GWP (8.8%), moderate GWP (62%), low GWP (20.70%) and very low GWP (6.6%). Validation of the AHP model with boreholes yield data shows a correlation coefficient of 71.3% giving a good prediction; (4) Conclusions: AHP and GIS can be used to successfully map GWP areas which could serve as an exploration guide for sustainable management of groundwater resources in semi-arid areas.

Cross-industry clusters are important for the economic prosperity of a region. However, studies are lacking to address competitive clusters among the aviation and tourism industries. Thus, this paper considers the case of both industries in terms of clusters and synergies formed. This research aim is to provide an understanding of both industries' protagonists' involvement in contributing to knowledge insights on the establishment of synergies or clusters among the two industries. Cyprus is highly dependent on tourism and aviation because they facilitate connectivity. The research is filled with semi-structured interviews with the main players and organizations of the airline and tourism industries (government bodies, airports, airlines, tour operators, and hotels). The results are indicative and suggest that, in a small geographical context, the notion of clusters involves a synergetic relationship among tourism stakeholders. Airlines’ role is important because it has an effect on all stakeholders involved in tourism.

Mobility is a vital welfare indicator which may influence broilers’ daily activities. Classical broiler mobility assessment methods are laborious and cannot provide timely insights into their conditions. Here, we proposed a semi-supervised Deep Learning (DL) model, YOLOv5, combined with Deep Sort algorithm conjoined with our newly proposed algorithm, Neo-Deep Sort, for individual broiler mobility tracking. Initially, 1,650 labeled images from five days were employed to train the YOLOv5 model. Through semi-supervised learning (SSL), this narrowly trained model was then used for pseudo-labeling 2,160 images, of which 2,153 were successfully labeled. Thereafter, the YOLOv5 model was fine-tuned on the newly labeled images. Lastly, the trained YOLOv5 and the Neo-Deep Sort algorithm were applied to detect and track 28 broilers in two pens and categorized them in terms of hourly and daily traveled distances and speeds. SSL helped in increasing the YOLOv5 model’s mean Average Precision (mAP), in detecting birds, from 81% to 98%. As compared with the manually measured covered distances of broilers, the combined model provided individual broiler's hourly moved distances with a validation accuracy of about 80%. Eventually, individual and flock level mobilities were quantified while overcoming the occlusion, false and miss detection issues.

In eutrophic waters, such as Mikawa Bay, Japan, anoxic bottom water develops in summer. This causes sulfide release into seawater by sulfate reduction in the sediment, leading to environmental problems. The addition of iron to sediments is a method used to improve the sediment environment, which was devised from a natural phenomenon. However, this method has not yet been quantitatively evaluated. In this study, we aim to quantitatively evaluate the suppressive effect of iron on sulfide release. First, we develop a sediment model that focuses on S and Fe. We then attempted to reproduce the observations and experiments on sulfide dynamics using the model. Consequently, the proposed model was able to reproduce field sulfur and Fe dynamics in sediments. Additionally, the model described the characteristics of sulfide release considering the effects of additive iron materials. Finally, we conducted predictive calculations and quantitatively evaluated the effects of adding iron materials to the sediments in terms of sulfur and iron cycles.

In this paper, we have constructed a WKB approximation for graphene having a Y-shaped Kekul\'e lattice distortion and a special folding of the $\mbox{\boldmath$K$}$ and $\mbox{\boldmath$K$}^\prime$ valleys, which leads to very specific linear energy dispersions with two non-equivalent pairs of subbands. These obtained semi-classical results, which include the action, electron momentum and wave functions, are utilized to analyze the dynamics of electron tunneling through non-square potential barriers. In particular, we explore resonant scattering of an electron by a potential barrier built on Kekul\'e-distorted graphene. Mathematically, a group of consecutive equations for a semi-classical action have been solved by following a perturbation approach under the condition of small strain-induced coupling parameter $\Delta_0 \ll 1$ (a good fit to its actual value $\Delta_0 \backsim 0.1$). Specifically, we consider a generalized model for Kek-Y graphene with two arbitrary Fermi velocities. The dependence of the electron transmission amplitude on the potential profile $V(x)$ and band parameters of Kekul\'e-patterned graphene has been explored and analyzed in details.

: Our study aim to test the influence of RGB reflectance and chlorophyll content on grain fill and grain yield of 15 durum wheat cultivars sown under semi-arid conditions. the evolution of chlorophyll content during three stages showed a stability during the heading stage, the chlorophyll content begins at this degradation during grain filling. Boutaleb genotype which was the best yielding genotype was characterized by low values ​​of RGB reflectance and high values ​​of majority of grain filling parameters and thousand kernels weight. Grain filling follows a sigmoid curve. Chlorophyll content was positively correlated with reflectance under the green band and negatively with both Red and Blue bands. A positive correlation was recorded between thousand kernel weight and grain yield, maximum grain dry weight and grain filling duration. The duration of the grain filling was positively influenced by the maximum dry weight of the grain and negatively by the grain filling ratio, the grain filling ratio was positively affected by reflectance at blue band. The principal component analysis separated the cultivars considered into 3 principal components, the absorption/reflectance component, the profitability component and the component of grain filling rate to which the local landrace Boutaleb belongs in terms of grain yield.

We generalize the dynamical analog of the Berry geometric phase setup to the quaternionic model of Avron et al. In our dynamical quaternionic system, the fast half-integer spin subsystem interacts with a slow two-degrees-of-freedom subsystem. The model is invariant under the 1:1:2 weighted SO(2) symmetry and spin inversion. There is one formal control parameter in addition to four dynamical variables of the slow subsystem. We demonstrate that the most elementary qualitative phenomenon associated with the rearrangement of the energy super-bands of our model consists of the rearrangement of one energy level between two energy superbands which takes place when the formal control parameter takes the special isolated value associated with the conical degeneracy of the semi-quantum eigenvalues. This qualitative phenomenon is of the topological origin, and is characterized by the second Chern class of the associated semi-quantum system. The correspondence between the number of redistributed energy levels and the second Chern number is confirmed through a series of examples.

Abstract: Droughts are complex and gradually evolving conditions of extreme water deficits which can compromise livelihoods and ecological integrity, especially in fragile arid and semi-arid regions that depend on rainfed farming, such as Kitui West in south-eastern Kenya. Against the background of low ground-station density, 10 gridded rainfall products and four gridded temperature products were used to generate an ensemble of 40 calculations of the Standardized Precipitation Evapotranspiration Index (SPEI) to assess uncertainties in the onset, duration and magnitude of past droughts. These uncertainties were driven more by variations between the rainfall products than variations between the temperature products. Remaining ambiguities in drought occurrence could be resolved by complementing the quantitative analysis with ground-based information from key informants engaged in disaster relief, effectively formulating an ensemble approach to SPEI-based drought identification to aid decision making. The reported trend towards drier conditions in Eastern Africa was confirmed for Kitui West by the majority of data products, whereas the rainfall effect on the increasingly dry conditions was more subtle than annual and seasonal declines and greater annual variation, which warrants further investigation. Nevertheless, the effects of increasing droughts are already felt on the ground and warrant decisive action.

In the context of improving the comfort and dynamics of the vehicle, the suspension system has been continuously developed and improved, especially using magnetorheological (MR) shock absorbers. The development of this technology which is relatively new has not been easy. Thus, the first widespread commercial use of MR fluid in a semi-active suspension system was implemented in passenger cars. The magnetorheological shock absorber can combine the comfort with the dynamic driving, because it allows the damping characteristic to be adapted to the road profile. The main objective of the paper is to analyze the dynamic behavior of the magnetorheological shock absorber in the semi-active suspension. In this sense, the author carried out a set of experimental measurements with a damping test bench, specially built and equipped with modern equipment. The results obtained from the experimental determinations show a significantly improved comfort when using a magnetorheological shock absorber, compared to a classic one, by the fact that the magnetorheological shock absorber allows to modify the damping coefficient according to the road conditions, thus maintaining the permanent contact between the tire and the road due to increased damping force.

In this study a new approach for planning Micro-Catchment Water Harvesting (M.C.W.H.) systems for irrigation in semi-arid regions such as the Aegean islands, is presented. M.C.W.H. is a cheap solution for constructing irrigation infrastructure with zero energy cost in regions where water is scarce. The proposed approach introduces simple linear relationships for estimating the annual volume of water V_s collected mainly from the CA (Contributing Area), stored in the root zone (Infiltration Basin, IB), according to the annual rainfall and runoff depths, after having determined the ratio of areas of micro-catchment (MC) components i.e. λ= Α_CA/Α_ΙΒ and its whole area A_MC This procedure was applied in Paros island of the Cyclades complex in the middle of the Aegean sea in east Mediterranean. Besides, income-cost analysis was performed via NPV method for almond, peach and apricot trees. The new approach was proved versatile and easy to use. Besides, the investment turned out to be advantageous two years after the MCs construction.

Purpose: Carotid intraplaque hemorrhage (IPH) increases risk of territorial cerebral ischemic events, but different sequences or criteria have been used to diagnose or quantify carotid IPH. The purpose of this study was to compare manual segmentation and semi-automatic segmentation for quantification of carotid IPH on magnetization-prepared rapid acquisition with gradient-echo (MPRAGE) sequences. Methods: Forty patients with 16–79% carotid stenosis and IPH on MPRAGE sequences were reviewed by two trained radiologists with more than five years of specialized experience in carotid plaque characterization with carotid plaque MRI. Initially, the radiologists manually viewed the IPH based on the MPRAGE sequence. IPH volume was then measured by three different semi-automatic methods, with high signal intensity 150%, 175%, and 200%, respectively, above that of adjacent muscle on the MPRAGE sequence. Agreement on measurements between manual segmentation and semi-automatic segmentation was assessed using the intraclass correlation coefficient (ICC). Results: There was near-perfect agreement between manual segmentation and the 150% and 175% criteria for semi-automatic segmentation in quantification of IPH volume. The ICC of each semi-automatic segmentation were as follows: 150% criteria: 0.861, 175% criteria: 0.809, 200% criteria: 0.491. The ICC value of manual vs. 150% criteria and manual vs. 175% criteria were significantly better than the manual vs. 200% criteria (p < 0.001). Conclusions: The ICC of 150% and 175% criteria for semi-automatic segmentation are more reliable for quantification of IPH volume. Semi-automatic classification tools may be beneficial in large-scale multicenter studies by reducing image analysis time and avoiding bias between human reviewers.

This paper is devoted to the study of reproducing kernels on 2-inner product Hilbert spaces. We focus on a new structure to produce reproducing kernel Hilbert and Banach spaces. According to multi-variable computing, this structures can be useful in electrocardiographs, machine learning and economy

Evaluating new, promising organic molecules to make next-generation organic optoelectronic devices necessitates the evaluation of charge carrier transport performance through the semi-conducting medium. In this work, we utilize quantum chemical calculations (QCC) and kinetic Monte Carlo (KMC) simulations to predict the zero-field hole mobilities of ~100 morphologies of the benchmark polymer poly(3-hexylthiophene), with varying simulation volume, structural order, and chain-length polydispersity. Morphologies with monodisperse chains were generated previously using an optimized molecular dynamics force-field and represent a spectrum of nanostructured order. We discover that a combined consideration of backbone clustering and system-wide disorder arising from side-chain conformations are correlated with hole mobility. Furthermore, we show that strongly interconnected thiophene backbones are required for efficient charge transport. This definitively shows the role "tie-chains" play in enabling mobile charges in P3HT. By marrying QCC and KMC over multiple length- and time-scales, we demonstrate that it is now possible to routinely probe the relationship between molecular nanostructure and device performance.

In order to coordinate the damping performance and energy regenerative performance of energy regenerative suspension, this paper proposes a structure of vehicle semi-active energy regenerative suspension with electro-hydraulic actuator (EHA). In light of the proposed concept, a specific energy regenerative scheme is designed and the mechanical properties test is carried out. Based on the test results, the parameter identification for the system model is conducted using recursive least squares algorithm. On the basis of system principle, the nonlinear model of the semi-active energy regenerative suspension with EHA is built. Meanwhile, LQG control strategy of the system is designed. And then the influence of the main parameters of EHA on the damping performance and energy regenerative performance of suspension is analyzed. Finally, the main parameters of EHA actuator are optimized via genetic algorithm. The test results show that when sinusoidal is input at the frequency of 2Hz and the amplitude of 30mm, the spring mass acceleration RMS value of optimized EHA semi-active energy regenerative suspension is reduced by 22.23% and energy regenerative power RMS value is increased by 40.51%, which means while meeting the requirements of certain vehicle ride comfort and driving safety, energy regenerative performance is improved significantly.

The microbial contamination in food packaging have been a major concern that paved the way for the search for natural based new anti-microbial agents, such as modified α-mangostin. In the present work, twelve synthetic analogs were obtained via semi-synthetic modification of α-mangostin by Ritter reaction, reduction by palladium-carbon (Pd-C), alkylation, and acetylation. The evaluation of the anti-microbial potential of the synthetic analogs showed higher therapeutic value than the parent molecule. The anti-microbial studies proved that I E showed higher antibacterial activity whereas I I showed most significant antifungal activity. Due to their microbial properties, modified α-mangostin can be utilized as active anti-microbial agents in food packaging.

This paper presents some results from a computational fluid dynamics (CFD) model of a multi-megawatt crosswind kite spinning on a circular path in a straight downwind configuration. The unsteady Reynolds averaged Navier-Stokes equations closed by the k−ω SST turbulence model are solved in the three-dimensional space using ANSYS Fluent. The flow behaviour is examined at the rotation plane, and the overall (or global) induction factor is obtained by getting the weighted average of induction factors on multiple annuli over the swept area. The wake flow behaviour is also discussed in some details using velocity and pressure contour plots. In addition to the CFD model, an analytical model for calculating the average flow velocity and radii of the annular wake downstream of the kite is developed. The model is formulated based on the widely-used Jensen’s model (Technical Report Risø-M; No. 2411, 1983), which was developed for conventional wind turbines, and thus has a simple form. Expressions for the dimensionless wake flow velocity and wake radii are obtained by assuming self-similarity of flow velocity and linear wake expansion. Comparisons are made between numerical results from the analytical model and those from the CFD simulation. The level of agreement was found to be reasonably good. Such computational and analytical models are indispensable for kite farm layout design and optimization, where aerodynamic interactions between kites should be considered.

Steady-state Reynolds-Averaged Navier-Stokes (RANS) simulations are performed for a leading-edge inflatable wing for airborne wind energy applications. Expanding on previous work where only the inflatable leading edge tube was considered, eight additional inflatable strut tubes that support the wing canopy are now included. The shape of the wing is considered to be constant. The influence of the strut tubes on the aerodynamic performance of the wing and the local flow field is assessed, considering flow configurations with and without side-slip. The simulations show that the aerodynamic performance of the wing decreases with increasing side-slip component of the inflow. On the other hand, the chordwise struts have little influence on the integral lift and drag of the wing, irrespective of the side-slip component. The overall flow characteristics are in good agreement with previous studies. In particular, it is confirmed that at a low Reynolds number of Re=10^5, a laminar separation bubble exists on the suction side of this hypothetical rigid wing shape with perfectly smooth surface. The destruction of this bubble at low angles of attack impacts negatively on the aerodynamic performance.

Bello's stochastic linear time-varying system theory has been widely used in the wireless communications literature to characterize multipath fading channel statistics. In the context of radar backscatter, this formulation allows for statistical characterization of distributed radar targets in range and Doppler using wide-sense stationary uncorrelated scattering (WSSUS) models. WSSUS models separate the channel from the effect of the waveform and receive filter, making it an ideal formulation for waveform design problems. Of particular interest in the radar waveform design community is the ability to suppress unwanted backscatter from the earth's surface, known as clutter. Various methods for estimating WSSUS system functions have been studied in the literature, but to date, no analytic expressions for radar surface clutter range-Doppler scattering functions exist. In this work we derive a wideband generalization of the Jakes Doppler spectrum model, which is widely used in the wireless communications literature, adapt it for use in radar problems, and show how the maximum entropy method can be used to extend this model to account for internal clutter motion. Validation of the spectral and stationarity properties of the proposed model against a subset of the Australian Ingara sea clutter database is performed, and good agreement is shown.

Gelephu, located in the Himalayan region, has experienced one of the strongest development activities due to the suitable topography and geographic location, which has led to rapid urbanization. The main objective of the study is to perform land use land cover (LULC) mapping for Gelephu for 2016 and 2023 by a Random Forest (RF) classifier, using the Semi-automatic Classification Plugin (SCP) in QGIS and identify LULC changes. Furthermore, the study assessed the vegetation change dynamics within the study area by analysing the Normalized Difference Vegetation Index (NDVI) for 2016 and 2023. Additionally, the study characterized the resulting LULC change for Gelephu Thromde, a sub-administrative municipal entity, as a result of the notable intensity of the infrastructure development activities. The current study used a framework to collect Sentiniel-2 satellite data, which was then used for pre- and post-processing to create LULC and NDVI maps. The classification model achieved high accuracy, with an area under the curve (AUC) of up to 0.89. The corresponding LULC and NDVI statistics were analysed to determine the current status of the LULC and vegetation indices, respectively. The LULC change analysis reveals urban growth of 5.65% and 15.05% for Gelephu and Gelephu Thromde, respectively. The NDVI assessment shows significant deterioration in vegetation health with a 75.11% loss of healthy vegetation in Gelephu between 2016 and 2023. This research provides the first version of LULC and NDVI maps of Gelephu. The analysis results indicate possible future implications on sustainable development management in Gelephu Bhutan.

Droughts are a common occurrence in various climates and are primarily caused by a prolonged decrease in rainfall. Several factors contribute to droughts, including temperature, wind speed, relative humidity, rainfall timing, amount, and intensity during the growing season. The objective of this study is to establish a new index, named soil moisture and evapotranspiration revealed drought index (SERDI), for displaying dry and wet conditions based on combining both soil moisture and evapotranspiration (Penman-Monteith) to improve drought early warning and its severity globally. For validation of the SERDI with other indices such as LST, VHI, NDVI, and NDWI, different ways used such as R-square, RMSE, MAPE, and P-value to estimate the accuracy, variability of data, the forecast conditions, and how the significance of data. The results showed that the low RMSE and high r² were found between SERDI with LST and VHI. In contrast, the low R- square and high RMSE were between SERDI with NDVI and NDWI in most of the semi-arid areas. Furthermore, most of the semi-arid areas from Iran, Iraq, Syria, Jordan, and Israel experienced moderate and severe dry conditions, except some parts of these regions had normal conditions in Iran and Syria. The SERDI analysis revealed a strong correlation between (LST) and a moderate correlation with (VHI) across all study areas. However, the relationship between other indices, like (NDWI) and (NDVI), varied depending on the regions. To conclude, SERDI can be used globally for detecting drought based on soil moisture and evapotranspiration.

Deep learning has been widely used in various tasks such as computer vision, natural language processing, and predictive analysis, recommendation systems in the past decade. However, practical scenarios often lack labeled data, posing challenges for traditional supervised methods. Semi-supervised classification methods address this by leveraging both labeled and unlabeled data to enhance model performance, but they face challenges in effectively utilizing unlabeled data and distinguishing reliable information from unreliable sources. This paper introduces ReliaMatch, a semi-supervised classification method that addresses these challenges by using a confidence threshold. It incorporates a curriculum learning stage, feature filtering, and pseudo-label filtering to improve classification accuracy and reliability. The feature filtering module eliminates ambiguous semantic features by comparing labeled and unlabeled data in the feature space. The pseudo-label filtering module removes unreliable pseudo-labels with low confidence, enhancing algorithm reliability. ReliaMatch employs a curriculum learning training mode, gradually increasing training dataset difficulty by combining selected samples and pseudo-labels with labeled data. This supervised approach enhances classification performance. Experimental results show that ReliaMatch effectively overcomes challenges associated with the underutilization of unlabeled data and the introduction of error information, outperforming the pseudo-label strategy in semi-supervised classification.

Desertification is impeding the implementation of reforestation efforts in Mongolia. Many of these efforts have been unsuccessful due to lack of technical knowledge on water and nutrient management strategies, limited financial support, and short-lived rainfall events. We investigated the effects of irrigation and fertilization on the morpho-physiological traits of Populus sibirica Hort. Ex Tausch and Ulmus pumila L. and to suggest irrigation and fertilization strategies for reforestation. Different irrigation and fertilizer treatments were applied: no irrigation, 2 L h-1, 4 L h-1 and 8 L h-1 of water; no fertilizer, 2 L h-1 + NPK, 4 L h-1 + NPK, and 8 L h-1 + NPK; and no compost, 2 L h-1 + compost, 4 L h-1 + compost, and 8 L h-1 + compost. The leaf area (LA) and specific leaf area (SLA) of both species responded positively to 4 L h-1 and/or 8 L h-1. Results also showed that the addition of either NPK or compost to 4 L h-1 and/or 8 L h-1 irrigation resulted in a higher LA, SLA, and leaf biomass (LB). Total chlorophyll content decreased with irrigation in both species. The same pattern was detected when a higher amount of irrigation was combined with fertilizers. Lastly, we found that both diurnal and seasonal leaf water potential of plants grown in 4 L h-1 and/or 8 L h-1 were significantly higher than in control plots. Therefore, 4 L h-1 and/or 8 L h-1 with either NPK or compost has shown to be the optimal irrigation and fertilization strategy for the species in an arid and semi-arid region of Mongolia. Results should provide us with a better understanding of tree responses to varying amounts of irrigation with or without fertilizer in pursuit of sustainable forest management in arid and semi-arid ecosystems.

A semi-structured interview (SSI) is one of the essential tools in conduction qualitative research. This essay draws upon the pros and cons of applying semi-structured interviews (SSI) in the qualitative research method. Moreover, the challenges of SSI during the coronavirus pandemic are critically discussed to provide plausible recommendations.

A proposed animal welfare assessment protocol for semi-arid rangeland-based cow-calf systems in Namibia combined 40 measures from a protocol developed for beef cattle in New Zealand with additional Namibia-specific measures. Preliminary validation of the protocol had been undertaken with five herds in one semi-commercial village. The aim of the current study was to apply this protocol and compare animal welfare across three cow-calf production systems in Namibia. A total of 2529 beef cows were evaluated during pregnancy testing in the yards of 17 commercial, 20 semi-commercial and 18 communal (total: 55) herds followed by an assessment of farm resources and a questionnaire-guided interview. Non-parametric tests were used to evaluate the difference in the welfare scores between the production systems. The results indicated a discrepancy of animal welfare between the three farm types, with a marked separation of commercial farms from semi-commercial, and communal village farms in the least. The differences in these production systems was mainly driven by economic gains through access to better beef export market for commercial farms and semi-commercial villages, as well as by the differences in the available grazing land, facility designs/quality and traditional customs in the village systems. The results indicate an advantage of commercialisation over communalisation.

Bacterial infections are world-wide problem and resistant bacteria is increasing globally that lead to treatments failure. Thus, it is important to find new techniques that are effective for the treatment antibiotic-resistant microorganisms. Green medicine used for the medication of different bacterial infection. Therefore , the study aimed to evaluate the immunomodulatory activity of essential fatty acid semi carbazide (EFASC) compounds extracted from flaxseed to eradicate resistance pathogens . Crud extracts of Linum usitatissimum was extracted by hexane for extraction of EFASC. The results of LD₅₀ appear that a live suspension of E.coli was 0.49×10⁷ ,while HK E.coli was 10⁸ , 125 mg /ml were the optimum dose in stimulate immune response of EFASC which gave maximum dose of total WBC , Neutrophil and Monocyte count. The immunomodulatory activity appear that E.coli + EFASC released moderate levels of IL-4 . HK E.coli release higher IL-4 lead to increase the hypersensitivity and hyper responses of immune system. HK + EFASC immunogen revealed moderate increased in IL-12 mean level 0.99 pg /ml, HK bacteria recorded 1.49 pg/ml, while the mean of EFASC revealed no significant different compare with control. An effective protection was observed in immunized groups with HK E.coli and EFASC challenged with 100 of LD50 of a live E.coli.

Membranes based on sulfonated synditoactic polystyrene were thoroughly characterized by contrast variation SANS over a wide Q-range in dry and hydrated states. The film samples were prepared by solid-state sulfonation that allowed a uniform sulfonation of only the amorphous phase while preserving the crystallinity of the membrane. The samples were loaded with different guest molecules in either the amorphous (fullerenes) or the crystalline (toluene) regions, in order to vary the neutron contrast or to reproduce the conditions enabling an increased resistance of the membranes to chemical decomposition. The use of uni-axially deformed film samples and contrast variation with different H2O/D2O mixtures allowed for the identification and characterization of different structural levels with sizes between nm and μm, which form and evolve in the membrane morphology in dry and hydrated states and produce scattering features on different detection sectors and at different detection distances after the sample, depending on their size and orientation.

Bamboo agroforestry is currently being promoted as a viable land use option to reduce dependence on natural forest for wood fuels in Ghana. To align the design and introduction of bamboo agroforestry in conformity with farmers’ needs, perceptions, skills and local cultural practices, information on its acceptability and adoption potential among farmers is necessary. It is therefore the objective of this study to (1) describe bamboo ethnobotany and (2) assess socioeconomic factors that affect the acceptability and adoption of bamboo and its integration into farming practices. Accordingly, information has been collected from 200 farmers in the dry semi-deciduous forest zone of Ghana. The study identified the socioeconomic risks and uncertainties as well as biophysical factors that are likely to influence the potential adoption of bamboo agroforestry in the study region. Gender, age, farmers’ known uses of bamboo, the practice of leaving trees on farmlands, farmers’ networking and access to extension services, land availability and ownership by farmers were identified as suitable predictor variables for the adoption of bamboo agroforestry. It is envisaged that bamboo agroforestry is a good bet in the DSFZ though there is the need to explore domestic energy (fuelwood) provision and substitution potential in order to have a broader picture of the technology.

Coastal dunes worldwide are increasingly under pressure from the adverse effects of human activities. Therefore, more and more restoration measures are being taken to create conditions that help disturbed coastal dune ecosystems regenerate or recover naturally. However, many projects lack (open-access) monitoring observations needed to signal whether further actions are needed, and hence to learn by doing. This submission presents an open access data set of 37 high-resolution digital elevation models and 24 orthomosaics collected before and after the excavation of five artificial foredune trough blowouts ("notches") in winter 2012/2013 in the Dutch Zuid-Kennemerland National Park, one of the largest coastal dune restoration projects in northwest Europe. These high-resolution data provide a valuable resource for improving understanding of the biogeomorphic processes that determine the evolution of restored dune systems, as well as developing guidelines to better design future restoration efforts with foredune notching.

Responding to an urgent call for effective and cost-efficient enforcement of emission regulations from ocean-going vessels (OGVs) at sea, the Royal Belgian Institute of Natural Sciences, one of the 17 official partners of the Belgian coastguard structure, launched its airborne sniffer program in 2015. A custom-built sniffer sensor was installed on board of the Belgian coastguard aircraft and has been used for the in-situ measurement of SO2 and NOx in OGV exhausts, providing non-compliance alerts to port inspection authorities in Belgium and other EU member states. To guarantee the consistency in quality and reliability of the airborne non-compliance alerts, the standard operational procedures and measurement methodology have been described and recorded in a sniffer quality management system (SQMS). As part of the SQMS, alerting thresholds for non-compliance with SO2 and NOx standards were defined based on the emission limits and the measurement uncertainty. In addition, compliant measurements for the fuel sulfur content (FSC) were shared through Thetis-EU, which is the sulfur inspection database hosted by the European Maritime Safety Agency (EMSA). By providing both non-compliance alerts and compliant measurements to port inspection authorities, the coastguard aircraft fulfills a first-step in the enforcement chain. This article demonstrates that the reported alerts have not only led to several sanctions, but the analysis also showed that the provision of airborne alerts improved the efficiency of the port inspection authorities drastically, resulting in a cost-efficient improvement of their enforcement strategy. Port inspection authorities were able to follow-up on 46% of the generated FSC alerts. In addition, 43% of the alerted OGVs, which were followed up, were confirmed as non-compliant after a port inspection. Accordingly, conditions were in place to effectively sanction 20% of the non-compliant observations. For NOx alerts, a limited follow-up was done by port inspection authorities and none of the alerts were confirmed by those inspections, which is mainly due to the lack of suitable inspection mechanisms and the absence of additional EU implementation regulations on NOx emission inspections. Aiming at paving the way for a stricter enforcement of airborne non-compliance alerts, a validation analysis was done between the airborne FSC measurements and reference FSC measurements. In addition to onboard measurements from exhaust gas cleaning systems (EGCS), analyzes of fuel samples were also carried out by port inspection authorities in order to acquire reference measurements. The validation analysis presented in this study showed that the empiric deviation of the airborne FSC measurements with the reference measurements was significantly lower than the uncertainty used in the reporting thresholds. It has also been shown that aerial measurements provide evidence-based data that, given an appropriate confidence interval, has the potential to be considered reliable legal evidence.

The primary objective of this current study is to conduct a comprehensive review of existing literature that discusses research on post and core restorations, covering aspects such as their composition, manufacturing methods, and clinical effectiveness. The methodology employed in this review encompasses the implementation of a well-defined search strategy, the establishment of criteria for inclusion and exclusion, and the selection of relevant studies to summarize their findings. To gather relevant literature published between 1993 and 2023, the research team conducted separate searches on PubMed, Scopus, and Embase databases. In total, 165 titles were initially retrieved from these electronic databases. By applying the predefined exclusion criteria, the researchers identified 73 articles that specifically address the conventional and computer-aided design/computer-aided manufacturing (CAD/CAM) technologies employed in post and core restorations. These restorations are frequently utilized procedures for repairing teeth that have undergone endodontic treatment and subsequently lost dental structure. The development of computerized technology for the creation of customized posts and cores has emerged as a straightforward and efficient alternative to traditional methods. The review encompasses a synthesis of papers discussing the various techniques and materials employed in constructing post and cores using CAD/CAM technology. Notably, different strategies for restoring endodontically treated teeth through CAD/CAM post and cores have been documented, revealing both direct and indirect approaches. The most mentioned materials for these restorations include zirconia, composite resin, and hybrid ceramics. While the available literature on CAD/CAM post and core procedures is somewhat limited, the review underscores the need for further research to explore the long-term outcomes and efficacy of this treatment approach.

Chipman contends, in stark contrast to the conventional view, that utility is not a real number but a vector and is inherently lexicographic in nature. According to these views, it will be proved that, for every preordered topological space (X,≾,t), the assumption t to be finer than the order topology t≾ on (X,t), i.e. t⊇t≾, and the assumption the quotient topology t∣∼≾ that is defined on the preordered set (X∣∼,≾∣∼) of indifference classes of ≾ to be Hausdorff imply that a cardinal number κ and a (complete) preorder ≲ on {0,1}κ that is coarser than the lexicographical ordering ≤lex on {0,1}κ, i.e. ≤lex⊂≲, can be chosen in such a way that there exists a continuous order-embedding ϑ:(X,≾,t)⟶({0,1}κ,≲,t≤lex). This theorem will be compared with a theorem that, in particular, describes necessary and sufficient conditions for ≾ to have a continuous multi-utility representation.

Stipa tenacissima (S. tenacissima), or esparto, is a perennial tussock grass that coexists with Pinus halepensis (P. halepensis) in semi-arid mediterranean woodlands. This research was carried out to explore diurnal transpiration at leaf level in esparto grass under different levels of pine-esparto competition and in contrasting environmental conditions of soil water. The measurements were spanned from the summer 2020 to spring 2021. The relationship between transpiration and competence was conducted in open and closed P. halepensis stands and taken into account the type of leave (green, senescent) and the maturity of the esparto grass. We observed a higher control of transpiration in green leaves, and correlations between transpiration and soil water were noted exclusively in this type of leaf. Our results substantiated a significant impact of pine competitors on transpiration of esparto grass, particularly during seasons characterized by high water-demand scenarios: the summer drought period and the commencement of the growing and flowering period (spring). Furthermore, our findings confirmed a greater response to transpiration in mature bushes compared to young ones under severe water stress, denoting higher adaptation to drought as esparto ages. Our results may have important implications for the dynamics and management of these semi-arid mixed woodlands, as well as the planning of reforestation programs aimed at restoring esparto grass steppes.

Immunohistochemistry is a powerful technique, widely used in biomedical research and clinics, that allows to determine the expression levels of some proteins of interest in tissue samples by means of the intensity of color due to the expression of biomarkers using specific antibodies. As such, immunohistochemical images are complex and problematic to be quantified. Recently we proposed a novel method including a first separation stage based on nonnegative matrix factorization (NMF) that achieved good results. However, that method was highly dependent on sparseness and non-negativity parameter choice and on algorithm initialization. Furthermore, the previously proposed method needed a reference image as starting point for the NMF algorithm. In the present work, we propose a new, simpler and robust method for the automated unsupervised scoring of immunohistochemical images based on bright field. Our work is focused on images from tumor tissues marked with blue (nuclei) and brown (protein of interest). The new proposed method represents a simpler approach that, in one side, avoids the use of NMF for the separation stage, and in the other side, circumvents the need for a control image. This new approach determines the subspace spanned by the two colors of interest by means of principal component analysis (PCA) with dimension reduction. This subspace is a two-dimensional space, allowing the finding of color vectors by considering the peaks of density of points. The method also develops a new scoring stage by avoiding, again, reference images, making the procedure more robust and less dependent on the parameters. Experiments for the semi-quantitative scoring of images in five categories exhibit promising and consistent results when compared to manual scoring carried out by experts.

The asymmetric synthesis of polyunsaturated triene C18:3 n-3 and C18:3 n-6 methoxylated ether lipids (MEL) of the 1-O-alkyl-sn-glycerol type is described as possible structural candidates for a triene C18:3 MEL of an unknown identity found in a mixture of shark and dogfish liver oil. Their C18:3 hydrocarbon chains constitute an all-cis methylene skipped n-3 or n-6 triene framework, along with a methoxyl group at the 2'-position and R-configuration of the resulting stereogenic centre. The methoxylated polyenes are attached by an ether linkage to the pro-S hydroxymethyl group of the glycerol backbone. The syntheses were based on the polyacetylene approach that involves a semi-hydrogenation of the resulting triynes. Both syntheses were started from our previously described enantio- and diastereomerically pure isopropylidene-protected glyceryl glycidyl ether, a double-C3 building block that was designed as a head group synthon for synthesis of various types of MELs.

Multibeam echo-sounders provide ideal data for semi-automated seabed feature extraction and accurate morphometric measurements. However, these methods have not been tested in morphologically highly complex environments. In this study, bathymetric and raw backscatter data were initially used to manually map the complex reef morphology found in the semi-enclosed Gera Gulf, in the northern Aegean Sea (Greece). A large number of reefs (more than 7000) were detected, making manual mapping extremely time-consuming. Benthic Terrain Modeller (BTM) was selected as a semi-automated method to map the reefs. The BTM did not function properly in this irregular relief and the results were discouraging. Trying to improve the BTM functionality, both bathymetry and slope were modified (enhanced); this time, the BTM outcome was unexpectedly improved, producing accurate results that appeared to exceed the accuracy of manual mapping. To compare the final maps with the distribution of the reefs, mapcurves were created to estimate the Goodness-of-Fit (GOF), while Precision, Recall, and F1 Score were also calculated. GOF values suggest more than 50% overlap between the resulting polygons while, Precision, Recall and F1 score resulted in values higher than 0.78 suggesting good detection accuracy for the semi-automated method. It becomes apparent that BTM provided more efficient results in comparison to the time-consuming manual mapping. This study asserts that semi-automated mapping stands as an effective method for delineating the geomorphometry of intricate relief and serves as a powerful tool for habitat mapping and decision-making.

Wheat yield plays an important role in the global economy. Changing climate conditions and increased drought negatively affect grain yield. Currently, breeding programs are aimed at improving wheat productivity. To accelerate the selection process of hybrids and parental forms for crosses, it is essential to pay attention to plants' phenotypic and genetic potential. We studied the genes of the "green revolution" group Rht and coarse-grained TaGW and TaGS to increase yields by selecting optimal parameters for wheat. We focused on short-stemmed and coarse-grained characteristics in a dry climate and conducted a correlation analysis between the genetic potential of wheat varieties and hybrids and their phenotypic manifestation in drought conditions. Rht-D1b significantly reduced the height of plants by 51.67% and reduced the coleoptile length by 30.45%. At the same time, TaGW8-B1a increased the grain width by 13.37%. However, in the presence of Rht-D1b and Rht-B1b in the genome, the 1000-kernal weight was 35.06 g (p<0.05), the Rht-B1b gene enhanced it by 9% (p<0.05), while both Rht-D1a and Rht-B1a alleles gave a 1000-kernal weight of 37.96 g (p<0.05). The Rht-D1b and Rht-B1b alleles gave 18.5 seeds per ear, while the Rht-D1a and Rht-B1a alleles gave the value of grains per ear -24.1 pcs. The data obtained indicated the relationship of phenotypic and genetic parameters in wheat between the coarse-grained and short-stemmed genes, which makes it possible to select based on the genetic parameters of varieties and hybrids, thereby speeding up the selection process.

Minimum housing standards aim to safeguard housing rights and enhance residential conditions. Governments develop housing policies, including provision, preservation, and support for welfare programs, guided by the status of households below these standards. Growing nations commonly utilize this approach to decrease the proportion of households not meeting these criteria. In South Korea, the ratio of households below these standards was 4.5% in 2021, down from 16.6% in 2006, as indicated by the initial Korea Housing Survey. However, this downward trend has stalled over the past decade. With the 2004 and 2011 revisions, the standards have been effective for 12 years, yet no longer mirror current housing realities due to ongoing improvements. This study aimed to propose enhancements to Korea’s minimum housing standards. Through analyzing laws, prior research, present household statuses, international cases, and expert insights, recommendations emerged. Categorizing households by size, we developed precise standards covering area, facility, and location aspects. These new standards led to an 8.4% non-compliance rate in 2021. This research’s findings anticipate aiding the revision of minimum housing standards, formulating pragmatic policies for enhancing residential conditions in line with present situations.

The third trimester of pregnancy is the most critical period for human brain development, during which significant changes occur in the morphology of the brain. The development of sulci and gyri allows considerable increase of the brain surface. In premature childrens, these alterations take place outside the womb that may cause a disruption of the normal brain maturation process. We hypothesize that a normalized atlas of brain maturation with cerebral ultrasound images from birth to term equivalent age will help clinicians assess these changes. This work proposes a semi-automatic GUI platform for segmenting the main cerebral sulci in the clinical setting from ultrasound images. This platform has been obtained from images of a cerebral ultrasound neonatal database images provided by two clinical researchers from the Hospital Sant Joan de Déu in Barcelona, Spain. The primary objective is to provide a user-friendly design platform for clinicians, for running and visualizing an atlas of images validated by medical experts. This GUI offers different segmentation approaches, pre-processing tools, and is friendly designed for running, visualizing images, and segmenting the principal sulci. The presented results are discussed in detail in this paper, providing an exhaustive analysis of the proposed approach’s effectiveness.

Recently, a paper was written to reformulate and strengthen the theory of semi-structured complex numbers H (a new number set invented to enable division by zero). Whilst the paper had profound results, the application of this number set in many areas of engineering and science has not been fully explored. Consequently, the aim of this paper was to establish the number set H as a useful mathematical tool by providing an amalgam of results arising from its application in several areas of engineering and science. In the process, this paper makes four major contributions: these are (1) determining the product of the gradients of a horizontal and vertical line; (2) developing new Euler formulas relating exponential, trigonometric and hyperbolic functions in the 3D semi-structured complex number Euclidean space; (3) establishing semi-structured complex numbers as a better extension of the complex number set than quaternions; (4) resolving singularities that may arise in engineering and science equations (because of division by zero) to develop reasonable conclusions in the absence of experimental data. These results and their applications provide a firm foundation to advance the number set H as a useful mathematical tool.

In this paper, in order to provide proper parameters for the preparation of semi-solid billets, the semi-solid annealing of hot-rolled 2A14 Al alloy was investigated. The microstructure was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) with X-ray energy dispersive spectrometer (EDS) and electron backscattered diffraction (EBSD), scanning transmission electron microscope (STEM). XRD results show that with the increase of temperature, equilibrium θ-Al2Cu gradually dissolved in the matrix. The EDS results of SEM and STEM show that there were coarse θ-Al2Cu phase, ultra-fine precipitate Al(MnFeSi) or (Mn, Fe)Al6 phase and atomic clusters in the microstructure. EBSD results show that the recrystallization mechanism was dominated by continuous static recrystallization (CSRX), the homogeneous nucleation occurred when the sample was heated to near solidus temperature, and CSRX happened in the semi-solid temperature. In the process of recrystallization, the micro-texture changed from preferred orientation to random orientation. A variety of experimental results show that static recrystallization (SRX) occurred at semi-solid temperature due to the blocking effect of atomic clusters on dislocation slip and the Zener drag effect of fine precipitates on low angle grain boundaries (LAGBs) disappeared with melting at semi-solid temperature.

The study aimed to develop standards for a welfare assessment protocol, by validating potential categorisation thresholds for assessment of beef farms in various beef cow-calf production systems in Namibia. Forty measures combined from a New Zealand-based protocol plus Namibia-specific measures, were applied on 55 beef farms (17 commercial farms, 20 semi-commercial and 18 communal village farms) during pregnancy testing, and a questionnaire guided interview. The categorised measures on a 3-point welfare score of 0: good 1: marginal and 2: poor/unacceptable welfare were subsequently compared with derivation of thresholds based upon the poorest 15% and best 50% of herds for each measure. Overall combined thresholds of continuous measures across the 3 farm types, showed 10/22 measures that posed welfare compromise across Namibia, where commercial farms had 4/22 measures and semi-commercial and communal village farms had 12/22 and 11/22 respectively with high thresholds. Most measures-imposed thresholds were retained because of significant importance to welfare of animals and preventiveness of the traits, while leniency was given to adjust good feeding and mortality measures to signify periods of drought. Handling measures (fearful, falling/lying) and abrasions thresholds were adjusted to reflect the temporary stress caused by infrequent cattle handling, and faulty yard designs/design and possible cattle breed influence on handling. Hence, the country needs prioritised investigation of underlying contributing factors and remediation to reduce the high thresholds.

To determine the photon emission or absorption probability for a diatomic system in the context of the semiclassical approximation it is necessary to calculate the characteristic canonical oscillatory integral which has one or more saddle points. Integrals like that appear in a whole range of physical problems, e.g. the atom-atom and atom-surface scattering and various optical phenomena. A uniform approximation of the integral, based on the stationary phase method is proposed, where the integral with several saddle points is replaced by a sum of integrals each having only one or at most two real saddle points and is easily soluble. In this way we formally reduce the codimension in canonical integrals of "elementary catastrophes" with codimensions greater than 1. The validity of the proposed method was tested on examples of integrals with three saddle points ("cusp" catastrophe) and four saddle points ("swallow-tail" catastrophe).

The aim of this article is to extend the local as well as the semi-local convergence analysis of multi-point iterative methods using center Lipschitz conditions in combination with our idea, of the restricted convergence region. It turns out that this way a finer convergence analysis for these methods is obtained than in earlier works and without additional hypotheses. Numerical examples favoring our technique over earlier ones completes this article.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

The snow melt from the High Atlas is a critical water resource in Morocco. In spite of its importance, monitoring the spatio-temporal evolution of key snow cover properties like the snow water equivalent remains challenging due to the lack of in situ measurements at high elevation. Since 2015, the Sentinel-2 mission provides high spatial resolution images with a 5 day revisit time, which offers new opportunities to characterize snow cover distribution in mountain regions. Here we present a new data assimilation scheme to estimate the state of the snowpack without in situ data. The model was forced using MERRA-2 data and a particle filter was developed to dynamically reduce the biases in temperature and precipitation using Sentinel-2 observations of the snow cover area. The assimilation scheme was implemented using SnowModel, a distributed energy-balance snowpack model and tested in a pilot catchment in the High Atlas. The study period covers 2015-2016 snow season which corresponds to the first operational year of Sentinel-2A, therefore the full revisit capacity was not yet achieved. Yet, we show that the data assimilation led to a better agreement with independent observations of the snow height at an automatic weather station and the snow cover extent from MODIS. The performance of the data assimilation scheme should benefit from the continuous improvements in MERRA-2 reanalyses and the full revisit capacity of Sentinel-2.

Risk-averse areas such as the medical, aerospace and energy sectors have been somewhat slow towards accepting and applying Additive Manufacturing (AM) in many of their value chains. This is partly because there are still signicant uncertainties concerning the quality of AM builds. This paper introduces a machine learning algorithm for the automatic detection of faults in AM products. The approach is semi-supervised in that, during training, it is able to use data from both builds where the resulting components were certied and builds where the quality of the resulting components is unknown. This makes the approach cost ecient, particularly in scenarios where part certication is costly and time consuming. The study specically analyses Selective Laser Melting (SLM) builds. Key features are extracted from large sets of photodiode data, obtained during the building of 49 tensile test bars. Ultimate tensile strength (UTS) tests were then used to categorise each bar as `faulty' or `acceptable'. A fully supervised approach identied faulty specimens with a 77% success rate while the semi-supervised approach was able to consistently achieve similar results, despite being trained on a fraction of the available certication data. The results show that semi-supervised learning is a promising approach for the automatic certication of AM builds that can be implemented at a fraction of the cost currently required.

Carbon nanotubes (CNTs) are effective supports for nano metals and together they represent hybrids that combine unique properties of both. A microwave induced reaction was used to deposit nano palladium on carboxylated and octadecylamine functionalized multiwall CNTs, which were used to carry out C-C coupling reactions in DMF and toluene. These hybrids showed excellent catalytic activity with yield as high as 99.8% while its enhancement with respect to commercially available Pd/C catalyst reached as high as 109%, and the reactions times were significantly lower. Polarity of the functionalized form was found to be a significant factor with the polar carboxylated CNT showing better activity in DMF while the relatively nonpolar octadecyl amine was better in toluene. The results suggest the possibility of tailor making functionalized CNT when used as catalyst supports

In the present work, we investigate the possibility that long-range airborne transport of infectious aerosols could initiate an epidemic outbreak at distances downwind beyond one hundred kilometers. For this, we have developed a simple atmospheric transport box-model which, for a hypothetical case of a COVID-19 outbreak, was compared to a more sophisticated 3-dimensional transport-dispersion model (HYSPLIT) calculation. Coupled with an extended Wells-Riley description of infection airborne spread, it shows that, the very low probability of outdoor transmission can be compensated by high numbers and densities, such as occurs in large cities, of infected and susceptible people in the source upwind and in the target downwind respectively. This may result in the creation of a few primary cases. It is worth pointing out that the probability of being infected remains very small at the individual level. Therefore, this process alone, which depends on population sizes, geography, seasonality and meteorology, can only “trigger” an epidemic which could then spread by the standard infection routes

Soil texture is key information in agriculture for improving soil knowledge and crop performance, so the accurate mapping of this crucial feature is imperative for rationally planning cultivations and for targeting interventions. We studied the relationship between radioelements and soil texture in the Mezzano Lowland (Italy), a 189 km² agricultural plain investigated through a dedicated airborne gamma-ray spectroscopy survey. The K and Th abundances were used to retrieve the clay and sand content by means of a multi-approach method. Linear (simple and multiple) and non-linear (machine learning algorithms with deep neural networks) predictive models were trained and tested adopting a 1:50,000 scale soil texture map. The comparison of these approaches highlighted that the non-linear model introduces significant improvements in the prediction of soil texture fractions. The predicted maps of the clay and of the sand content were compared with the regional soil maps. Although the macro-structures were equally present, the airborne gamma-ray data permits us shedding light on finer features. Map areas with higher clay content were coincident with paleo-channels crossing the Mezzano Lowland in Etruscan and Roman periods, confirmed by the hydrographic setting of historical maps and by the geo-morphological features of the study area.

Coronavirus disease 2019 (COVID-19), caused by the novel coronavirus SARS-CoV-2, has been confirmed in over 10,000,000 individuals worldwide and has resulted in more than 500,000 deaths in a few months since it first surfaced. With such a rapid spread it is no surprise that there has been a massive effort around the world to collectively elucidate the mechanism by which the virus is transmitted. Despite this, there is still no definitive consensus regarding droplet versus airborne transmission of SARS-CoV-2. Public health officials around the world have introduced guidelines within the scope of droplet transmission. However, increasing evidence and comparative analysis with similar coronaviruses, such as severe acute respiratory syndrome (SARS-CoV-1) and middle eastern respiratory syndrome (MERS), suggest that airborne transmission of SARS-CoV-2 cannot be effectively ruled out. As the data supporting COVID-19 airborne transmission grows, there needs to be an increased effort in terms of technical and policy measures to mitigate the spread of viral aerosols. These measures can be in the form of broader social distancing and facial covering guidelines, exploration of thermal inactivation in clinical settings, low-dose UV-C light implementation, and greater attention to ventilation and airflow control systems. This review summarizes the current evidence available about airborne transmission of SARS-CoV-2, available literature about airborne transmission of similar viruses, and finally the methods that are already available or can be easily adapted to deal with a virus capable of airborne transmission.

Facial acne is a prevalent dermatological condition regularly observed in the general population. This study introduces a novel deep learning model for facial acne segmentation utilizing a semi-supervised learning method known as bidirectional copy-paste, which synthesizes images by interchanging foreground and background parts between labeled and unlabeled images during the training phase. To overcome the lower performance observed in the labeled image training part compared to the previous methods, a new framework was devised to directly compute the training loss based on labeled images. The effectiveness of the proposed method was evaluated against previous semi-supervised learning methods using images cropped from facial images at acne sites. The proposed method achieved a Dice score of 0.5205 in experiments utilizing only 3% of labels, marking an improvement of 0.0151 to 0.0473 Dice score over previous methods. The proposed semi-supervised learning approach for facial acne segmentation demonstrates improvement in performance, offering a novel direction for future acne analysis.

How hands-on gardening impacts behaviors including healthy eating and physical activity during early childhood can be of critical importance for preventing early onsets of obesity. This research investigates how participating in hands-on gardening impacts preschoolers’ (3-5 years old) physical activity (measured by accelerometers) in childcare centers in the Semi-Arid Climate Zone. The research was conducted in eight licensed childcare centers located in West Texas with 149 children (n=149). Four childcare centers in the experimental group received hands-on garden interventions; the other four in the control group did not. In both experimental (intervention) and control (non-intervention) centers, children wore Actigraph GT3X+ accelerometers continuously for 5 days before and for 5 days after intervention (a total of 10 days). Results show that the duration of sedentary behavior of children in the experimental (intervention) group significantly decreased compared to children in the control (non-intervention) group. The finding suggests that the positive effects of childcare hands-on gardening on physical activity extend to semi-arid climate zones where gardening is challenging due to high temperatures and lack of annual rainfall. The research emphasizes the critical need to incorporate hands-on gardening in childcare centers as an obesity prevention strategy nationally in the U.S. and beyond.

Towards better understanding of factors controlling carbon (C) exchange between inland waters and atmosphere, we addressed inorganic carbon cycle in semi-arid lakes of Central Eurasia, subjected to strong impact of on-going climate change. For this, we assessed the hydrochemical vari-ability and quantified its control on formation of authigenic carbonate minerals, occurring within the upper layer of sediments in 43 semiarid lakes located in the southwest of Western Siberia (Central Eurasia). Based on measurements of pH, total dissolved solids (TDS), cationic and anionic composition, dissolved organic and inorganic C, as well as textural and mineralogical characterization of bottom sediments using X-ray diffraction and scanning electron microscopy, we demonstrate that lake water pH and TDS are primarily controlled by both lithological and climatic context of the lake watershed. We have not revealed any direct relationships between lake morphology and water chemistry. The most common authigenic carbonates scavenging atmospheric CO2 in the form of insoluble minerals in lake sediments were calcite, aragonite, Mg-calcite, dolomite and hydro-magnesite. The calcite was the most common component, aragonite mainly appears in lakes with sediments enriched in gastropod shells or artemia cysts, while hydromagnesite was most common in lakes with high Mg/Ca molar ratios, as well at high DIC concentrations. The relationships between mineral formation and water chemistry established in this study can be generalized to a wide suite of arid and semi-arid lakes in order to characterize current status of inorganic C cycle and predict its possible modification under on-going climate warming such as water temperature rise and change of hydrological connectivity, primary productivity and nutrient regime.

Keywords: glycerin; Ni-based catalyst; lanthanum; semi-industrial scale; hydrogen production; biorefinery; monitoring.

The positional deviation of the Automatic Emergency Call System (AECS) under collision conditions brings difficulties for post-rescue operations. Currently, there is a lack of analysis on the system operating conditions during collisions in the reliability assessment methods for the Global Navigation Satellite System (GNSS) deployed in AECS. Therefore, this paper establishes an in-vehicle collision environment simulation model for emergency calls to explore the influence of parameters such as temperature and vibration on the data deviation of the simulated GNSS system. We also propose environmental limits applicable to comprehensive AECS tests, which can objec-tively evaluate the reliability of AECS and provide data support for AECS bench test. Through the satellite signal-based semi-physical simulation, AECS is subjected to bench test under different operating conditions. The findings of this study demonstrate that the occurrence of random vibra-tion and impact stress, induced by vibration, exerts considerable disruptive effects on positional signal data during collisions. Consequently, it leads to substantial interference with the accurate detection of post-collision satellite positioning information. When the simulation operates under a 2.4gRMS vibration condition, the maximum phase noise error in the positioning system is 8.95%, which does not meet the AECS test accuracy requirements. On the other hand, the semi-simulation system is less affected by temperature changes, and at the maximum allowable temperature dif-ference of the equipment, the maximum phase noise error in the simulated signal is 2.12%. Therefore, based on the influence of phase noise variation on the accuracy of satellite signal simulation, nec-essary environmental conditions for AECS test are obtained, including the temperature consistent with the maximum operating temperature of the vector generator and the vibration Power Spectral Density (PSD) lower than 1.2gRMS.

The paper proves a theorem about the structure of the distribution function on which the extremum of fractionally linear functional is reached in the presence of an uncountable number of linear constraints. The problem of finding an extremal distribution function arises when determining the optimal control strategy in a class of Markov homogeneous randomized control strategies. The structure of extremal functions is described by a finite number of parameters, hence the problem is greatly simplified since it is reduced to the search for an extremum of some function.

Semi-structured complex numbers H was a number set developed to enable division by zero in ordinary algebraic equations. Its utility has been shown in mathematics and engineering. However, very little has been done to show its usefulness in computer science. Consequently, the aim of this paper was to show the utility of semi-structured complex numbers in computer science by developing a division by zero calculator. First two computer programs were written, one for a standard (STD) calculator and the other for a division by zero (DBZ) calculator. The programs were fed 20000 randomly generated arithmetic equations of varying lengths and the space and time complexity associated with processing these equations were measured and compared to determine the efficiency of each calculator. In the process, three major contributions were made: (1) A representation for semi-structured complex numbers that enables it to be easily used by a computer was developed; (2) It was demonstrated that the DBZ calculator outperforms the STD calculator in terms of efficiency; and, (3) It was shown that the number set H reduced the amount of error handling required to run a computer program. These results provide a firm foundation to advance the number set as a useful tool in computer science.

A new set of alkoxy alcohols were synthesised by reaction of eugenol oxirane with aliphatic and aromatic alcohols. These eugenol derivatives were evaluated against their effect upon the viability of the insect cell line Sf9 (Spodoptera frugiperda).The most promising compounds, 4-(3-(tert-butoxy)-2-hydroxypropyl)-2-methoxyphenol and 4-(2-((4-fluorobenzyl)oxy)-3-hydroxypropyl)-2-methoxyphenol were submitted to in silico assays to predict possible targets. Thought an Inverted Virtual Screening approach, 23 common pesticide targets were screened and the top 2 targets predicted were further evaluated through molecular dynamics simulations and free energy calculations. In addition, these to eugenol derivatives were subjected to encapsulation and release assays using liposome-based nanosystems of egg phosphatidylcholine/cholesterol (7:3), with encapsulation efficiencies higher than 90% and release profiles well described by both Korsmeyer-Peppas and Weibull models.