The effects of 0.4wt.% Sc addition on a typical Al-Si10-Mg alloy were systematically investigated in the present research. Samples with and without Sc produced refined dendritic arranged microstructures with sensitivity to the aging treatment after solidification, particularly in the case of the alloy without Sc. After being exposed to 300°C for 90 minutes, the dendritic spacing nearly doubled in the Al-10wt.%Si-0.45wt.%Mg samples. The rapidly solidified microstructures were constituted by the -Al dendritic phase surrounded by eutectic phases/intermetallics such as Si, Mg2Si and Al3Sc (in the case of the alloy containing Sc). 255°C and 300°C were deemed most appropriate temperatures for aging treatments, with four exposure times of up to 120 minutes tested for each alloy. The heat treatments allowed the Vickers hardness profiles to be plotted and compared. Moreover, in order to detect both Sc- and Mg- precipitates after aging, specific samples have been prepared for either SEM or TEM analyses. At first, the results pointed to a strong precipitate-related hardening effect formed as a result of the Sc addition to the alloy. All samples containing Sc showed a higher hardness value when compared to their respective treated samples without Sc. Secondly, when comparing the Al-10Si-Mg-Sc alloy samples among themselves after being treated at different conditions, high temperatures and excessive treatment times can become detrimental to the hardness. This was due to the growth of larger Sc-bearing precipitates of approximately 1 µm in size under such conditions, having less pronounced hardening effect. The best condition (255°C for 60 min) for as centrifuged samples in Cu-mold produced very fine dispersion of Mg- and Sc- intermetallics (~200 nm in size) with a peak hardness of 110 HV.

Bauxite residue (BR) is a well promising resource for critical metals and especially scandium (Sc), a rare and expensive metal with increasing applications in advanced technology. Particularly, Greek BR’s composition indicates a sound possibility for a commercially viable recovery of Sc under the conditions of an optimized leaching process and the subsequent use of advanced separation techniques. Leaching with mineral acids emerges as the dominant selection with comparison to other techniques. This study investigates an optimized leaching condition set on Sc recovery, using sulfuric acid as the most suitable among different acids tested, in the context of process economics and environmental constraints. Several variables were studied individually or combined in order to achieve high Sc concentration in the leachate as well as to ensure selectivity, especially in respect to iron. The most significant parameters proved to be the solid to liquid ratio (S/L), the final pH value as well as the use of recycling of leachate on fresh BR batches. The proposed process, using sulfuric acid at low acid molarities under ambient conditions was integrated rapidly leading to high and selective Sc recovery. A flow diagram of the developed leaching process in industrial scale was proposed based on continuous operation.

Bauxite residue is the voluminous by-product of alumina production after Bayer process. Its high alkalinity causes disposal problems and harmful environmental impacts. However, the residue contains significant amounts of valuable elements such as rare earth elements including scandium. Greek bauxite residue contains a high amount of scandium close to its main resources. Taking into account scandium limited availability coupled with its high demand in modern technology, bauxite residue could be considered as a potential resource for scandium recovery. In this study, the optimization of scandium extraction from bauxite residue with sulfuric acid is investigated using Taguchi methodology. Based on previous studies acid molarity, leaching time, solid/liquid ratio and reaction temperature were selected as control parameters for the selective Sc recovery. Method optimization targeted the highest concentration of scandium combined with the lowest concentration of iron without taking into account applications constraints. The predicted values resulted by Taguchi methodology were affirmed by a confirmation experiment conducted at optimal conditions. Regression analysis provided the respective equations to be applied on several conditions depending on different applications.

One of the potential sources of rare-earth elements (REEs) is the solid waste from alumina industry - bauxite residue, known as “red mud” (RM). The main REEs from the raw bauxite are concentrated in RM after the Bayer leaching process. The earlier worldwide studies were focused on the scandium (Sc) extraction from RM by concentrated acids to enhance the extraction degree. This leads to the dissolution of major oxides (Fe2O3 and Al2O3) from RM. This article studies the possibility of selective Sc extraction from alkali fusion red mud (RMF) by diluted nitric acid (HNO3) leaching at pH ≥ 2 to prevent co-dissolution of Fe2O3. RMF samples have been analyzed by X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), electron probe microanalysis (EPMA), and inductively coupled plasma mass spectrometry (ICP-MS). Sc extraction has been found to be 71.2 % at RMF leaching by HNO3 at pH=2 and at 80 °C during 90 min. The kinetic analysis of experimental data by the shrinking core model has shown that Sc leaching process is limited by the interfacial diffusion and the diffusion through the product layer. The apparent activation energy (Ea) was 19.5 kJ/mol. We have established that according to EPMA of RMF, Sc is associated with iron minerals; it could act as the product layer. The linear dependence of Sc extraction of magnesium (Mg) extraction has been revealed. This fact indicates that Mg can act as a leaching agent of Sc presented in RMF by ion-exchangeable phase.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

Aiming at the industrial scale development of a Scandium (Sc)-selective leaching process of Bauxite Residue (BR), a sufficiently numerous set of process design aspects has been investigated, by appropriate exploitation of available experimental data. The interpretation of experimental data for Sc leaching yield, with sulfuric acid as the leaching solvent, has shown significant impact from acid feed concentration, mixing residence time, liquid to solids ratio, and times of leachate re-usage onto fresh BR. The thin film diffusion model, as the fundamental theory for leaching, either with constant particle size for selective leaching, or with shrinking particle size for less-, or non-, selective leaching, interprets sufficiently well the relevant experimental data. In both cases, a concept for an unyielding core supplements the basic model. Especially for the selective leaching mild conditions, the simplest model version keeps step with the experiments, since both prove 1^st order kinetics, while especially for the extreme conditions including very low solvent excess, it is proposed a combined conversion rate model with diffusion and chemical reaction inside particles. The maximization of Sc recovery per unit of consumed solvent (i.e., specific recovery) emerged as highly critical for the process economics.

The present study aimed to investigate the effect of cold deformation on the precipitation kinetics of a binary CuSc alloy containing 0.4 wt.% scandium using the experimental analysis method of differential scanning calorimetry (DSC). Non-deformed and 75% cross-section reduced cold-rolled, supersaturated specimens were tested at non-isothermal DSC runs at up to five different heating rates. The DSC results showed that cold deformation significantly accelerated the precipitation process in the binary alloy, leading to a decrease in the initial and peak temperatures of the exothermic reactions. The activation energies calculated with the Kissinger method, indicated that the precipitation activation energy decreased with increasing cold deformation. The findings of this study provide worthy implications to further optimize the processing of Cu-Sc alloys with improved mechanical properties.