Strain-hardening cement-based composites (SHCC) are a novel class of fiber-reinforced concretes which exhibit high tensile strain capacity prior to failure localization. Although the tensile behavior of SHCC has been a matter of study in numerous research works, the behavior of these composites under other loading modes has scarcely been investigated. The article at hand addresses the mechanical behavior of two types of normal-strength SHCC subject to uniaxial tension, torsion, and combinations of torsional and axial loading. The SHCC under investigation were made with polyvinyl-alcohol (PVA) and ultra-high molecular weight polyethylene (UHMWPE) fibers, respectively. Digital Image Correlation (DIC) was applied to evaluate the multiple cracking process and crack opening modes in conjunction with the concretes’ axial and torsional loading histories. The study demonstrates the suitability of torsion experiments to assess the multi-axial and shear performance of SHCC, highlights the relation between multiple cracking and transfer capacity for shear forces, and emphasizes the importance of the type of reinforcing fibers on the shear strength and ductility of such composites.

This paper presents a numerical two-scale framework for the simulation of fiber reinforced concrete under impact loading. The numerical homogenization framework considers the full balance of linear momentum at the microscale. This allows for the study of microscopic inertia effects affecting the macroscale. After describing the ideas of the dynamic framework and the material models applied at the microscale, the experimental behavior of the fiber and the fiber-matrix bond under varying loading rates are discussed. To capture the most important features, a simplified matrix cracking and a strain rate sensitive fiber pullout model are utilized at the microscale. A split Hopkinson bar tension test is used as an example to present the capabilities of the framework to analyze different sources of dynamic behavior measured at the macroscale. The induced loading wave is studied and the influence of structural inertia on the measured signals within the simulation are verified. Further parameter studies allow the analysis of the macroscopic response resulting from the rate dependent fiber pullout as well as the direct study of the microscale inertia. Even though the material models and the microscale discretization used within this study are still simplified, the value of the numerical two-scale framework to study material behavior under impact loading is shown.

The ductile behavior of strain hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions for applications where high energy dissipation is needed, such as earthquake, impact by a projectile, or blast. However, the superior tensile ductility of SHCC due to multiple cracking does not necessarily entail compressive and shear ductility. As an effort to characterize the behavior of SHCC under impact compressive and shear loading, relevant to the mentioned high-speed loading scenarios, the paper at hand studies the performance of a SHCC and its constituent cement-based matrices using the split-Hopkinson bar method. For compression experiments, cylindrical specimens with a length-to-diameter ratio (l/d) of 1.6 were used. The selected length of the sample led to similar failure modes under the quasi-static and impact loading conditions, which was necessary for a reliable comparison of the obtained compressive strengths. The impact experiments were performed in a split-Hopkinson pressure bar (SHPB) at a strain rate that reached 110 s-1 at the moment of failure. For shear experiments, a special adapter was developed for a split-Hopkinson tension bar (SHTB). The adapter enabled performing impact shear experiments on planar specimens using the tensile wave generated in the SHTB. Results showed a dynamic increase factor (DIF) of 2.3 and 2.0 for compressive and shear strength of SHCC, respectively. As compared to the non-reinforced constituent matrix, the absolute value of the compressive strength was lower for the SHCC. Contrarily, under shear loading, the SHCC yielded the higher shear strength than the non-reinforced matrix.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

Despite all their advantages, load-bearing concrete shell structures with double curvatures are not frequently in use. The main reason is the complexity of their construction. In such a context, this article starts with a brief, critical review of existing technologies while their pros and cons are highlighted. Against that background the authors then propose a new approach for the highly automated fabrication of gridshell structures from variable modules. To demonstrate the feasibility of such a new technology, a demonstrator called ConDIT 1.0, a sphere-like shell structure composed of several frames was designed and built. The frame modules were fabricated automatically using extrusion-based 3D printing and a printable, strain-hardening cement-based composite (SHCC). This article presents the design of ConDIT 1.0, the mechanical material characterization of printed SHCC, the technology of module production, the results of geometry verification for print modules using 3D scanning, and the procedure for the demonstrator’s assembly.

The performance of a normal-strength SHCC under impact loading was studied using the results obtained from a split Hopkinson tension bar (SHTB). The focus of the investigation is to explain the mechanisms behind the peculiar rate-dependent behavior of SHCC under tensile loading. With the help of frames obtained by high-speed cameras and the subsequent Digital Image Correlation (DIC) analysis, the stress-strain relation of the SHCC obtained in SHTB was analyzed. The investigation of the composite’s behavior was supported by constituent-level experiments on the non-reinforced matrix of the SHCC and on the fiber-matrix bond. In the case of the constituent matrix, the well-known apparent increase in the tensile strength of the cement-based matrix and its influence on the behavior of SHCC was studied. For this purpose, experiments on the SHCC specimens with different geometries were performed in the SHTB. The results obtained from these experiments and those obtained by DIC show that commonly used analytical models, in which the specimen is assumed elastic, cannot capture the effects of structural inertia on the results. Thus, an alternative novel method based on the results of DIC has been used to explain and quantify the contribution of structural inertia. The rate-dependent behavior of the fiber-matrix bond was studied by performing high-speed single fiber pullout tests in a miniaturized split Hopkinson tension bar. This novel experimental technique enabled explanation of the rate-dependent bridging action of the fibers in SHCC. Based on the results, the enhanced behavior of SHCC under impact loading is explained.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.