High Vacuum Flat Plate Collectors (HVFPCs) are the only type of Flat Plate Thermal Collectors capable of producing thermal energy for middle-temperature applications (until 180 °C). As the trend of research plans to develop new Selective Solar Absorbers to extend the range of HVFPC application until 250 °C, it is necessary to correctly evaluate the collector efficiency up to such temperature to predict the energy production accurately. We propose an efficiency model for these collectors based on the selective absorber optical properties. The proposed efficiency model explicitly includes the radiative heat exchange with the ambient, which is the main source of thermal losses for evacuated collectors at high temperatures. It also decouples the radiative losses that depend on the optical properties of the absorber adopted from the other thermal losses due to HVFPC architecture. The model has been validated by applying it to MT-Power HVFPC manufactured by TVP-Solar, and it has been used to predict the efficiency and energy production of HVFPC equipped with new, optimized selective solar absorbers developed in recent years.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.

We investigate the performance of a novel flat photovoltaic-thermal (PV-T) module under high-vacuum through a 1D numerical model based on steady-state energy balance, with the aims of optimizing the simultaneous production of thermal and electrical energy. In the proposed design, the photovoltaic (PV) cell is positioned directly above the selective solar absorber (SSA), in a multilayer or fully integrated PV-SSA structure, which allows full exploitation of spectral solar radiation. In fact, in this configuration the losses related to non-absorption of low-energy photons and thermalization, typical of a classical single-junction PV cell, are reduced. The present study is conducted as the emittance and energy bandgap of the PV layer varied, thus admitting a wide variety of materials into the analysis. The dependence of the temperature coefficient, β(%/K), on the energy bandgap of the PV cell is also included. In the last part of the work, we discuss the performance of the proposed evacuated PV-T equipped with a SSA layer and thin film solar cells, namely those made of CdTe, CdS and GaAs. Overall, the paper highlights the great advantage of using high vacuum insulation, which suppresses conductive losses, and the versatility of the proposed system, which could be adapted to the user's needs simply by choosing the appropriate material for the photovoltaic layer.

This study refers to the optimization of a Selective Solar Absorber to improve the Sun-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal collectors. Efficiency has been evaluated by using analytical formula and a numerical thermal model. Both results have been experimentally validated using a commercial absorber in a custom experimental set-up. The optimization procedure aimed at obtaining Selective Solar Absorber is presented and discussed in the case of a metal dielectric multilayer based on Cr2O3 and Ti. The importance of adopting a real spectral emissivity curve to estimate high thermal efficiency at high temperatures in selective solar absorber is outlined. Optimized absorber multilayers can be 8% more efficient than the commercial alternative at 250 °C operating temperatures and up to 27% more efficient at 300 °C. Once the multilayer has been optimized the choice of a very low emissivity substrate such as copper allows to further improve efficiency and to reach stagnation temperature higher than 400 °C without Sun concentration.

A new frontier in solar thermal panel technology can be a high vacuum collector, thick enough to be equipped with solar concentrators based on non-imaging optics, such as the Compound Parabolic Concentrators (CPC). The high vacuum technology guarantees higher operating temperatures thanks to the enhanced thermal insulation, which leads to pay particular attention to the absorber radiative emission. In this paper by means of numerical simulations we compare the efficiency of a flat selective solar absorber under high vacuum to the efficiency of a CPC under high-vacuum collector.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Multilayer absorbers based on Cr2O3 and Cr, designed to improve the Solar-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal panel, are fabricated via sputtering deposition on bulk copper substrates and characterized by thermal and optical analysis. The refractive index of the single layers has been measured and used to estimate absorber thermal efficiency at the operating temperatures. Multilayers have been produced via sputtering deposition on bulk copper substrates. The absorber multilayers can be 10% more efficient than the commercial alternative at 250 °C operating temperatures, reaching 380 °C stagnation temperature without Sun concentration. The thermal stability has been checked at temperature of 400 °C in vacuum for four hours. High vacuum flat thermal collectors, equipped with the produced selective solar absorbers can obtain unprecedented performances and can give important contribution to the energy transition from fossil fuels to renewable energy for efficient heat production.

Among solar thermal collectors, the evacuated flat panel is emerging as a reference technology for operation at higher temperatures of up to 200 °C with an increased annual energy production owing to both direct and diffuse light capture. Accurate measurements of the optical properties of the selective absorbers used in such devices are key for a reliable estimation of the overall performance. These optical properties must be measured under high vacuum at high temperatures, conditions under which the panels are meant to operate. In this study, we accurately measured these properties using a calorimetric technique. The measurement procedure is based on a power balance equation for a flat sample suspended in a high-vacuum chamber with minimal thermal losses and is well adapted for this class of devices. Calorimetric measurements obtained under Sun and LED light revealed excellent reproducibility and good agreement with those obtained using traditional optical analysis at low temperatures in air. When extended up to the absorber stagnation temperature, which often exceeds 300 °C, the calorimetric measurements started to deviate from the optical measurements, indicating the importance of measuring under the operating conditions.

The fabrication of thin-film multilayer structures by sputtering technique usually requires multi-cathode deposition machine. This study proposes a simpler approach based on the RF power modulation: silicon nitride (SiN$_x$) thin films were prepared by RF reactive sputtering in (Ar + N$_2$) atmosphere at room temperature. The samples were analyzed to highlight the effects of different deposition conditions on the morphological and optical properties of the films in the visible and near/mid-IR regions. The refractive index of the films was changed in the range of 1.5 - 2.5 (at $\lambda$=800 nm) by tuning the sputtering power. IR reflectance measurements revealed the absence of spurious (oxygen- or hydrogen-based) phases, while atomic force and scanning electron microscopies confirmed the presence of flat and defect-free samples surfaces.

Uniform illumination is a key requirement in different research fields. However, this requirement is often difficult to achieve when high intensity is required at the same time. Recent advancements in LED lamps allow nowadays for compact and economical solutions. In this work we present a suitable solution for various laboratory purposes requiring stable, uniform and high intensity illumination. The system is composed of four identical high power white LED arrays of 30 mm diameter each, placed on a supporting and cooling structure having a minimum volume of 26 cm x 26 cm x 8 cm. A numerical model has been developed, based on a ray tracing software, in order to simulate the performances. These have then been experimentally validated with measurements of the power density map, carried out with a 1% uncertainty pyranometer. Data show that the built system is very stable over time and provides an illumination uniformity higher than 98%, on a surface of 50 mm radius, which reduces to 95% on a surface of 75 mm radius. The power density can be adjusted in the 390-1360 W m-2 range, not affecting uniformity.

In the quest for more efficient solar thermal systems, accurately determining the thermal emittance of low-emissive materials is crucial in determining the power losses. This paper describes the calorimetric method designed to precisely measure the thermal emittance of Selective Solar Absorbers (SSAs) to be used in High Vacuum Flat Plate Collectors (HVFPCs). The method's capability is demonstrated through the successful correction of thermal emittance values for copper samples of varying sizes, including dimensions down to 49 cm². Results highlight the method's potential to significantly reduce measurement errors associated with small-size and/or low-emittance samples, providing a path forward to improve the design and efficiency of SSAs. This research marks a significant step in advancing solar thermal technology by enabling emittance measurements with a precision better than 0.003, which is essential for the development of high-performance solar thermal absorbers. The method has also been applied to correct the thermal emittance value of SSA measured in previous measurement campaigns, and it allows a better estimation of the SSA efficiency conversion curve.

CKD in HF patients is very common condition, their dysfunction is closely linked and influence each other, so their management required multidisciplinary and personalized approaches. The diagnosis of HF and CDK relies on signs and symptoms. Several tools, such as blood-based biomarkers and echography help us to clarify and discriminate the main characteristics of these patients. Evidence in improving survival due to new drug-employment in HF, has increasingly challenged physicians to manage patients with multiple diseases, especially in patients with CKD. The difficulty is in the safe administration of these drugs in patients with HF and CKD. Knowing up to which values ​​of creatinine or renal clearance any drug can be administered is fundamental. We wanted to summarize, on this sizable and complex topic, the experiences of various prior study to get clearer ideas and a more precise reference about the assessment and management of HF and CKD.