The aim of the experiment was to determine the effect of strontium oxide addition on zirconium silicate recrystallization when adding strontium oxide to the glaze composition. Zirconia glazes (4 different contents) were prepared to which strontium oxide was added in amounts of 0, 1, 3, 6, and 12 mass%. SrO. The characteristic temperatures of the raw glazes were measured, based on which the maximum firing temperatures were determined. The fired glazes were subjected to study of the phase composition and observation of the microstructure. Analysis of the characteristic temperatures showed a fluxing effect, but it was not as strong for all glazes. Differences in the amount of the crystalline phase of zirconium silicate obtained in fired glazes and the partial transition of zirconium silicate to the amorphous phase were observed. Observations of the microstructure clearly indicated an increase in the homogeneity of the distribution of zirconium silicate.

The widely adopted temperature for solid solution heat treatment (ST) for the conventionally fabricated Inconel 718 is 1100 °C for a hold time of 1 h or less. This ST scheme is however not enough to dissolve Laves and annihilate dislocations completely in samples fabricated with Laser metal powder bed fusion (L-PBF) additive manufacturing (AM)-Inconel 718. In spite this, the highest hardness obtained after aging for ST temperatures (970 - 1250 °C) is at 1100 °C/1h [1]. The unreleased residual stresses in the retained lattice defects are potentially affecting other properties of the material. Hence, this work aims to investigate if a longer hold time of ST at 1100 °C will lead to complete recrystallization while maintaining the strength after aging or not. For this study, L-PBF-Inconel 718 samples were ST at 1100 °C at various hold times (1, 3, 6, 9, 16 or 24 h) and aged to study the effects on microstructure and hardness. In addition, a sample was directly aged to study the effects of bypassing ST. The samples (ST and aged) gain hardness by 43 – 49 %, depending on hold time. A high density of annealing twins evolved during 3 h of ST and the quantity only slightly varies for longer ST.

This paper presents the results of investigations of the effects of hot deformation parameters in compression investigation on the austenite grain size in HSLA steel (0.16% C, 0.037% Nb, 0.004% Ti, 0.0098% N). The axisymmetric compression investigations were performed on cylindrical investigation specimens of d=1.2 using the Gleeble 3800 simulator. The strain rate=1s^-1÷15.9s^-1 and strain degree ε=1.2. Before deformation, the research specimens were austenitized at TA = 1100 ÷ 1250 °C. Metallographic observations of the primary austenite grains were conducted with an optical microscope, while the structure of dynamically recrystallized austenite, inherited by martensite, was examined by EBSD technique using a scanning electron microscope. Based on the analysis of investigation results, it was found that the size of dynamically recrystallized austenite grains in HSLA steel were clearly affected by hot compression parameters. In contrast, no significant impact of austenitising temperature on their size was found.

The material undergoes high temperature and high strain rate deformation process during cutting process, may induce the dynamic recrystallization behavior and result the evolution of dynamic mechanical properties of the material to be machined. In this paper, the modified Johnson-Cook(J-C) model for Nickel based powder metallurgy superalloy considering dynamic recrystallization behavior in high strain rate and temperature is proposed. The dynamic mechanical properties of the material under different strain rates and temperature conditions are obtained by quasi-static compression test and split Hopkinson pressure bar (SHPB) test. The coefficients of the modified J-C model are obtained by linear regression method. The modified model is verified by comparison with experimental and model prediction results. The results show that the modified J-C model proposed in this paper can accurately describe the mechanical properties of nickel-based powder metallurgy superalloys at high temperature and high strain rate. Which provides help for studying the cutting mechanism and finite element simulation of nickel-based powder metallurgy superalloy.

In this paper, in order to provide proper parameters for the preparation of semi-solid billets, the semi-solid annealing of hot-rolled 2A14 Al alloy was investigated. The microstructure was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) with X-ray energy dispersive spectrometer (EDS) and electron backscattered diffraction (EBSD), scanning transmission electron microscope (STEM). XRD results show that with the increase of temperature, equilibrium θ-Al2Cu gradually dissolved in the matrix. The EDS results of SEM and STEM show that there were coarse θ-Al2Cu phase, ultra-fine precipitate Al(MnFeSi) or (Mn, Fe)Al6 phase and atomic clusters in the microstructure. EBSD results show that the recrystallization mechanism was dominated by continuous static recrystallization (CSRX), the homogeneous nucleation occurred when the sample was heated to near solidus temperature, and CSRX happened in the semi-solid temperature. In the process of recrystallization, the micro-texture changed from preferred orientation to random orientation. A variety of experimental results show that static recrystallization (SRX) occurred at semi-solid temperature due to the blocking effect of atomic clusters on dislocation slip and the Zener drag effect of fine precipitates on low angle grain boundaries (LAGBs) disappeared with melting at semi-solid temperature.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Calcium dihydrogen phosphate monohydrate [Ca(H2PO4)2·H2O] (a fertilizer) was successfully synthesized by the recrystallization process by using a prepared triple superphosphate (TSP) that derived from oyster shell waste as starting material. This bio-green, eco-friendly process to produce an important fertilizer can promote a sustainable society. The shell-waste-derived TSP was dissolved in distilled water and kept at 30, 50, and 80 °C. Non-soluble powder and TSP solution were obtained. The TSP solution fraction were then dried and the recrystallized products (RCP30, RCP50, and RCP80) were obtained and confirmed as Ca(H2PO4)2·H2O. Whereas the non-soluble products (NSP30, NSP50, and NSP80) were observed as calcium hydrogen phosphate dihydrate (CaHPO4·2H2O). The recrystallized yields of RCP30, RCP50, and RCP80 were found to be 51.0%, 49.6%, and 46.3%, whereas the soluble percentages were 98.72%, 99.16%, and 96.63%, respectively. RCP30 shows different morphological plate sizes, while RCP50 and RCP80 present the coagulate crystal plates. X-ray diffractograms confirm the formation of both the NSP and RCP. The infrared adsorption spectra confirmed the vibrational characteristics of HPO42‒, H2PO4‒ and H2O existed in CaHPO4·2H2O and Ca(H2PO4)2·H2O. Three thermal dehydration steps of Ca(H2PO4)2·H2O (physisorbed water, polycondensation, and re-polycondensation) were observed. Ca(H2PO4)2 and CaH2P2O7 are the thermodecomposed products from the first and second steps, whereas the final product is CaP2O6.

In this study, the hot deformation of Cu-0.55Sn-0.08La (wt%) alloy was studied by gleeble-3180 testing machine at deformation temperatures of 400-700oC and various strain rates. The stress-strain curve showed that the hot deformation behavior of Cu-0.55Sn-0.08La (wt%) alloy was greatly affected by work hardening, dynamic recovery, and dynamic recrystallization. The activation energy Q was calculated as 287.141 kJ/mol , and hot compression constitutive equation was determined as ε ̇=[sinh(0.006388σ)]^12.123∙exp⁡(37.7505-287.141/RT). The microstructural evolution of the alloy during deformation at 400oC revealed the presence of both slip and shear bands in the grains. At 700oC, dynamic recrystallization grains were observed but recrystallization was incomplete. In sum, these results provided the theoretical basis for continuous extrusion process of alloys with promising future use.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

For a wide industrial application of magnesium alloys, a method for imparting high damping properties while maintaining mechanical properties is required. Controlling the crystallographic texture seems to be useful, because dislocations are known to have a significant influence on the damping characteristics of magnesium alloys. Therefore, the effect of twinning and annealing, which can affect to the recrystallization were investigated in this study. An AZ31 alloy was hot rolled at 673K with a reduction ratio of 10 % and 50 %, and then annealed at 673K and 723K for 0.5, 1, 2, and 3H respectively. SEM-EBSD was used to examine the microstructure and texture. In addition, each specimen’s hardness and internal friction were contemporarily measured. As a result, hot rolling produced tensile twins and their fraction increased with internal friction when the reduction ratio increased. Due to annealing, a discontinuous type of static recrystallization occurred within the twinning grains, and was highly activated along with the increasing annealing temperature and the fraction of twinning. In the samples annealed at 723K, the internal friction continuously increased over the annealing time, whereas in the samples annealed at 673K, the decrease in dislocation density was delayed while, the internal friction showed a relatively low value.