This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

The interaction between the grid network and the offshore wind power plant (WPP) network can lead to the amplification of certain harmonics and potentially resonant conditions. Offshore WPP should limit the increment of harmonic voltage distortion at the point of connection to the grid network as well as within their internal network. The harmonic distortion should be limited within the planning level limits using harmonic compensation, which is usually achieved by using static filters. In this paper an active damping compensation strategy with a STATCOM using emulation of resistance at the harmonic frequencies of concern is analysed. Such a compensation is effective for the local bus, though the performance is not guaranteed at the remote bus. This paper investigates the challenges associated with remote harmonic compensation in the offshore WPP, which is connected to the onshore grid through long high-voltage cables and transformers. First, the harmonic distortion and the compensating effects of the filter are theoretically assessed. Afterwards, they are demonstrated using harmonic propagation studies and time domain simulations in PSCAD.

A layout of urban waste fired zero emission power plant is described in this paper. The principle of layout, which comes from similar coal-fired plants retrieved from the literature, integrates gasification with a power generation section, and implements two parallel conversion processes, one supplied by the heat of the gasifier consisting of a thermoacousticmagnetohydrodynamic (TAMHD) generator, while in the second one the syngas is treated in order to obtain almost pure hydrogen, which is fed to fuel cells. The CO2 deriving from the oxidation of Carbon base is stocked in liquid form. The novelty of the proposed layout lies in the fact that the entire conversion is performed without solid moving parts. The resulting plant avoids any type of emissions in the atmosphere, increases mechanical efficiency as compared to traditional plants, thanks to the absence of moving parts, nonetheless, resolving at its root the ever-increasing waste-related pollution problems.

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

Power generation using renewable technologies has become a primordial option to satisfy the energy demand all over the world, being solar concentrating technologies widely applied for this purpose. A combination of Parabolic Trough Collector with Direct Steam Generation has been considered an excellent option for power generation, due to the economic cost and complexity in the plant are reduced. The thermal evaluation of the solar power plant as well as the PTC in the DSG process is very important in viability and economic analysis. In this sense, as the main objective of this work, a numerical tool for evaluating DSG with PTC technology has been developed. The software SOLEEC is a versatile, reliable, accurate and friendly to the user for thermally evaluating a DSG with PTC technology. The user has the possibility to compare the thermal behavior of different geometrical dimensions for a PTC; and even consider different materials; in order to satisfy the demand of superheated steam by a DSG process. The software has an error less than 5% when compared with literature results and in this paper is used to evaluate a power plant in Mexico obtaining that the change to DSG proposing different PTC could reduce the solar field about 35%.

The increasing variability in power plant load, in response to a wildly uncertain electricity market and the need to to mitigate CO₂ emissions, lead power plant operators to explore advanced options for efficiency optimization. Model-based, system-scale dynamic simulation and optimization are useful tools in this effort, and the subject of the work presented here. In prior work, a dynamic model validated against steady-state data from a 605 MW subcritical power plant was presented. This power plant model is used as a test-bed for dynamic simulations, in which the coal load is regulated to satisfy a varying power demand. Plant-level control regulates plant load to match an anticipated trajectory of the power demand. The efficiency of the power plant operating at varying load is optimized through a supervisory control architecture that performs set point optimization on the regulatory controllers. Dynamic optimization problems are formulated to search for optimal time-varying input trajectories that satisfy operability and safety constraints during the transition between plant states. An improvement in time-averaged efficiency of up to 1.8% points is shown feasible with corresponding savings in coal consumption of 184.8 tons/day and carbon footprint decrease of 0.035 kg/kWh.

A novel hybrid CSP-PV power plant is presented. Instead of the integration used in current hybrid power plants, where part of the PV production is charged into the thermal energy storage system through electrical resistors, the proposed system integrates both PV and thermal solar fields using a high-temperature heat pump. Both the heat pump and the heat engine are based on Brayton supercritical CO2 thermodynamic cycles. Such integration allows for charging the molten salts storage as if a central tower receiver field supplied the thermal energy, whereas parabolic trough collectors are employed. Unlike conventional hybrid plants, where the storage of PV production leads to a decrease in power injected into the grid throughout the day, the power injected by the proposed system remains constant. The heat engine efficiency is 44.4%, and the COP is 2.32. The LCOE for a 50 MWe plant with up to 12 hours of storage capacity is 171 $/MWh, which is lower than that of existing CSP power plants with comparable performance. Although the cost is higher compared to a PV plant with batteries, this hybrid system offers two significant advantages: it eliminates the consumption of critical raw materials in batteries, and all the electricity produced comes from a synchronous machine.

This short communication makes use of the principle of singular perturbation to approximate the ordinary differential equation (ODE) of prompt neutron (in the point kinetics model) as an algebraic equation. This approximation is shown to yield a large gain in computational efficiency without compromising any significant accuracy in the numerical simulation of primary coolant system dynamics in a PWR nuclear power plant. The approximate (i.e., singularly perturbed) model has been validated with a numerical solution of the original set of neutron point-kinetic and thermal–hydraulic equations. Both models use variable-step Runge–Kutta numerical integration.

Generator automatic voltage control device (AVC) is an automatic voltage and reactive power optimization control terminal on the power plant side. Aiming at improving the performance of generator automatic voltage control device, this paper introduces a detection method of AVC substation performance based on virtual dispatching terminal environment. During the testing, the upper computer of redundant power plant is connected to the virtual dispatching terminal environment to simulate the sending instructions of AVC master station, the behavior of AVC sub stations and the excitation system of generators. The performance of AVC substation is evaluated according to the feedback adjustment results, which can effectively detect the abnormal behavior of AVC substation in power plant.

This study aims to determine the optimal configuration (position and operation duration) for wall mounted mechanical mixers based on the comparison of three-dimensional computational fluid dynamics (CFD) modelling results and physical data collected from the treatment plant. A three-dimensional model of anoxic zone 1, 2 and 3 of Northern Wastewater Treatment Plant (WWTP) located at Cairns Regional Council, Cairns, Queensland, Australia was developed and validated. The model was used to simulate the flow pattern of the WWTP and the simulation results are in good agreement with the physical data varying between 0% to 15% in key locations. The anoxic zones were subject to velocities less than the desired 0.3 metres per second however results for suspended solids concentration indicate that good mixing is being achieved. Results for suspended solids concentrations suggest that the anoxic zones are towards the upper limits recommended by literature for specific power dissipation. The duration for operation of mechanical mixers was investigated and identified that the duration could be reduced from 900 seconds down to 150 seconds. Alternative mixer positioning was also investigated and identified positioning which would increase the average flow velocity with decreased duration (150 seconds). The study identified that Council may achieve savings of $24,000 per year through optimisation of the mechanical mixers.

Natural gas combined cycle power plants (CCPPs) are widely used to meet peak loads in electric energy production. Continuous monitoring of the output electrical power of CCPPs is a requirement for power performance. In this study, the role of ambient temperature change having the greatest effect on electric production is investigated for a natural gas CCPP. The plant has generated electricity for fourteen years and setup at 240 MW in Aliağa, İzmir, Turkey. Depending on the seasonal temperature changes, the study data were obtained from each gas turbine (GT), steam turbine (ST) and combined cycle blocks (CCBs) in the ambient temperature range of 8-23°C. It has been found that decreases of the electric energy in the GTs because of the temperature increase and indirectly diminishes of the electricity production in the STs. As a result, the efficiency of each GT, ST and CCB reduced, although the quantity of fuel consumed by the controllers in the plant was decreased. As a result of this data, it has been recommended and applied that additional precautions have been taken for the power plant to bring the air entering the combustion chamber to ideal conditions and necessary air cooling systems have been installed.

In this study, a tuned mass damper is proposed as a seismic acceleration mitigating technique of an electrical cabinet inside the nuclear power plant. In order to know the mitigation performance, the electrical cabinet and the tuned mass damper were modeled using SAP2000. The sine sweep wave was used to confirm the vibration characteristics of the cabinet over a wide frequency range, and the several various earthquakes were applied to the cabinet to verify the control performance of the tuned mass damper. After analyzing the numerical results, it is summarized that the application of the proposed technique can reduce the acceleration response of the cabinet.

The hybridization of conventional thermal power plants by incorporation of renewable energy systems has witnessed widespread adoption in recent years. This trend aims not only to mitigate carbon emissions but also to enhance the overall efficiency and performance of these power generation facilities. However, calculating the performance of such intricate systems using fundamental thermodynamic equations proves to be both laborious and time-intensive. Nevertheless, possessing accurate and real-time insights into their performance is of utmost significance to ensure optimal plant operation, facilitate decision-making, and streamline power production planning. In this paper, we delve into the application of machine learning techniques, particularly hybrid methodologies, to predict the performance of power plants. Specifically, we employ three approaches: the Adaptive Neuro-Fuzzy Inference System (ANFIS), the ANFIS optimized via Particle Swarm Optimization (ANFIS-PSO), and the ANFIS optimized through Genetic Algorithm (ANFIS-GA). These techniques are alternatively applied to a complex hybrid thermal power plant, namely an Integrated Solar Combined Cycle Power Plant (ISCCPP). This ISCCPP comprises a steam turbine section, a gas turbine section, and a concentrated solar power system utilizing troughs as collectors. The energy transfer fluid, in conjunction with exhaust from the gas turbine section, heats water within a vessel or steam generator, producing steam to propel the steam turbine's rotor. Electricity generation is facilitated by both gas and steam turbines, which are coupled to a generator. The findings of this study underscore the accuracy and appropriateness of ANFIS-based models in evaluating and predicting the performance of intricate hybrid power plants. The ANFIS model exhibited an impressive overall coefficient of correlation of 0.9991. Notably, the integration of evolutionary algorithms (PSO and GA) into the ANFIS framework elevated model performance, yielding correlation coefficients of 0.9994 for ANFIS-PSO and 0.9997 for ANFIS-GA. It is noteworthy that ANFIS-GA demonstrated superior predictive capability. The modeling framework developed in this research offers valuable support to designers, energy managers, and decision-makers. It provides a robust and dependable tool to assess the performance of hybrid thermal power plants, which are poised for a global surge in numbers amid the ongoing energy transition.

The paper presents the results of energy and environmental analysis of geothermal CHP plant operation in Polish conditions. As the most favorable, for the geothermal conditions prevailing in Poland, the variant of CHP plant based on Organic Rankine Cycle (ORC) has been taken into consideration. As the case study the existing geothermal well located in the town of Konin in the Wielkopolska voivodship has been chosen. The conceptual design of CHP plant has been proposed and evaluated from energy and environmental point of view. As energy performance criteria the non-renewable primary energy consumption has been chosen. In case of environmental performance carbon dioxide emission has been taken as evaluation criteria. The analysis has been performed for different operating conditions and three working fluids.

The vision of the community around Geothermal Power Plant (GPP) is the development of GPP should be based on sustainable development principles, without jeopardizing the quality of life and justice for communities surrounding the power plant. This research aims to: (i) identifying issues that arise as an impact of the development of GPP in the rural Tompaso, and (ii) finding solutions to the issues to minimize the conflict that arises from further GPP development in rural Tompaso and its surroundings. This study is based on the competitive intelligence (CI) research method. The results show that the development of GPP in Tompaso has a negative impact on the natural environment and social environment. The technical solutions offered include: (i) bioremediation by cultivating plants that absorb arsenic; (ii) biosulfurization and desulfurization for reducing air pollution, especially sulfur; (iii ) floods and extreme drought are managed by improving infrastructure and reforestation; (iv) social conflicts (land acquisition, working days, labor recruitment and settlement security) are solved by intensifying program dissemination to the community and involving local communities in decision making. The recommended policy is providing incentives to the local community through strategic programs for the development of human and natural resources.

Coal combustion in thermal power plants releases ash. Ash is reported to cause different adverse health hazards in humans and other organisms. Owing to the presence of radionuclides, it is also considered as a potential radiation hazard. In this study, based on the surface radiation measurements and relevant ancillary data, expected radiation risk zones were identified with regard to the human population residing near the Thermal Power Plant. With population density as the risk determining criteria, about 20% of the study area was at ‘High’ risk and another 20% of the study area was at ‘Low’ risk zone. The remaining 60% was under medium risk zone. Based on the findings remedial measures which may be adopted have been suggested.

In this contribution, we make an attempt to write a theoretical proposal for designing an eco friendly thermal power plant which runs with cold nuclear fusion technology at a temperature of (1500 to 2000) deg.C. In our recently published papers, we have proposed a clear cut mechanism for understanding and implementing cold nuclear fusion technique pertaining to fusion of hydrogen with metals of mass numbers starting from 50. In this context, we would like to stress the point that, fusion of hydrogen under controllable temperature and pressure can be understood as a phenomenon of fusing neutron to the nucleus of the base atom. Part of isotopic nuclear binding energy difference of final and base atomic nuclides can be seen in the form of safe thermal energy of the order of (1 to 3) MeV per atom against 200 MeV released in nuclear fission of one Uranium atom. Due to increased heaviness and weak interaction, sometimes fused neutron splits into proton and electron. Proton seems to be retained by the base atom’s nuclear core and electron seems to join with the electronic orbits of the base atom. In this way, increased mass of base atomic nuclide helps in eco friendly production of thermal energy in large quantity. For this purpose we consider Iron-56 as a fuel. In a simplified view, under strong nuclear attractive forces, Iron-56 absorbs hydrogen atom as a neutron and by emitting 1MeV equivalent thermal energy transforms to Iron-57. Thus, one gram of Iron-56 can generate 1000MJ of heat with 50% efficiency. In a shortcut approach, by bombarding powder and semi-liquid forms of Iron-56 with direct neutrons coming from neutron source, our proposal can be tried, understood and verified experimentally.

This study investigated the risk of lung and bladder cancers in people residing in proximity of a coal-oil-fired thermal power plant in an area of north-eastern Italy, covered by a population-based cancer registry. Incidence rate ratios (IRR) by sex, age, and histology were computed according to tertiles of residential exposure to benzene, nitrogen dioxide (NO2), particular matter, and sulfur dioxide (SO2) among 1076 incident cases of lung and 650 cases of bladder cancers. In men of all ages and in women under 75 years of age, no significant associations were observed. Conversely, in women aged >75 years significantly increased risks of lung and bladder cancers were related to high exposure to benzene (IRR for highest vs. lowest tertile: 2.00 for lung cancer and 1.94 for bladder cancer) and NO2 (IRR: 1.72 for lung cancer; and 1.94 for bladder cancer). In these women, a 1.71-fold higher risk of lung cancer was also related to a high exposure to SO2. The findings of this descriptive study indicated that air pollution may have a role with regard to the risk of lung and bladder cancers, limited to women aged ≥ 75 years. Such increased risk warrants further analytical investigations.

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

In this work, we investigate the ability of a data assimilation technique and space-borne observations to quantify and monitor changes in nitrogen oxides (NOx) emissions over North-Western Greece for the summers of 2018 and 2019. In this region, four lignite-burning power plants are located. The data assimilation technique, based on the Ensemble Kalman Filter method, is employed to combine space-borne atmospheric observations from the high spatial resolution Sentinel-5 Precursor (S5P) Tropospheric Monitoring Instrument (TROPOMI) and simulations using the LOTOS-EUROS Chemical Transport model. The Copernicus Atmosphere Monitoring Service-Regional European emissions (CAMS-REG, version 4.2) inventory based on year 2015 is used as the a priori in the simulations. Surface measurements of nitrogen dioxide (NO2) from air quality stations operating in the region are compared with the model surface NO2 output using either the a priori (base run) or the a posteriori (assimilated run) NOx emissions. The high biases found between the in situ NO2 measurements and the base run surface NO2 decrease in the assimilated run in most cases. The bias in the station near the largest power plant decreases to 2.0 μg/m3 (2.83 μg/m3) from 10.5 μg/m3 (8.46 μg/m3) in 2019 (2018 respectively). Concerning the estimated annual a posteriori NOx emissions it was found that, for the pixels hosting the two largest power plants, the assimilated run results in emissions decreased by ~40-50% for 2018 compared to 2015, whereas a larger decrease, of ~70% for both power plants, was found for 2019, after assimilating the space-born observations. For the same power plants, the European Pollutant Release and Transfer Register (E-PRTR) reports decreased emissions in 2018 and 2019 compared to 2015 (-35% and -38% in 2018, -62% and -72% in 2019), in good agreement with the estimated emissions. We further compare the a posteriori emissions to the reported energy production of the power plants during the summer of 2018 and 2019. Mean decreases of about -35% and-63% in NOx emissions are estimated for the two larger power plants in summer of 2018 and 2019, respectively, which are supported by similar decreases in the reported energy production of the power plants (~-30% and -70%, respectively).

In order to harmonize supply and demand of green energy, new future-proof technologies are needed. Here, hydrogen plays a key role. Within the current framework conditions, the production of green hydrogen is not yet economically viable. The use of the oxygen produced and the possible increase in efficiency associated with it mostly remains unconsidered. The aim is to demonstrate that the economic efficiency of a power-to-gas (PtG) project can be increased by using the by-product oxygen. In this research project, a water electrolyser connected to grid is powered to supply hydrogen to a hydrogen refuelling station. By utilising the by-product oxygen from water electrolysis for a wastewater treatment plant (WWTP), it is shown that the net present value (NPV) of the project can be improved by up to 13 % compared to the initial scenario. If a photovoltaic (PV) system is used in addition to grid electricity for higher green hydrogen production, the NPV can be further improved by up to 58 %. The levelized cost of hydrogen (LCOH) is calculated for different scenarios with and without oxygen configuration. A sensitivity analysis is then performed to find important parameters.

On 2013 the Villonaco wind farm (16.5 MW), the first wind farm in continental Ecuador near the city of Loja, began operations. The power generated is delivered to the National Interconnected System (SNI), which services the city. This research confronts two sets of real data, the electricity use of the urban area of Loja, and the power generated by the Villonaco Wind Farm. Electricity use follows clearly defined daily and weekly cycles, and wind power has a seasonal behaviour. The study shows that wind power integration cannot be a long-term stable power source regardless power or generation surplus. Another essential finding is that time series can be used as a statistical source to determine the need for short- (seconds) and long- (days, weeks) term energy storage. Strategies to further the energy autonomy of the urban area through the expansion of the wind farm by a factor of 2 are discussed.

This article introduces new method using ANN to control SVC in order to correct the source power factor of low voltage network. Two ANN approaches are investigated to design accurate and fast power factor correction (PFC) controller. First approach uses simple ANN (SANNA). Second approach uses cascaded ANN (CANNA). ANN regression, performance and the calculated error for both approaches are investigated to select between the two approaches. CANNA is selected as a better solution and it used to build the ANN PFFC controller using database, generated by MATLAB-Simulink, for standard three low voltage levels (240V, 220V and 110V). Nine test cases are carried out to validate the performance of proposed ANN PFC controller with a network has variable loads and low power factor (0.6 approximately). In order to extend the use of the controller to other voltage levels not included in the training process of the cascaded ANN, only the SVC is resized. Another nine cases are carried out with the same loads using the same ANN controller, as it is, to test its performance with the extended voltage level range (415V, 230V and 120V). The results show accurate and fast response in all test cases.

Power quality problem is a hot area in power systems and drives that has drawn the attention of many researchers. This is because of the threat it poses on the health of electrical systems and the cost incurred on utility bills. The problem arises as a result of the need for reactive power to be supplied alongside active power in power transmission and distribution. Unfortunately, reactive power is consumed by almost all components of the system, leading to a shortage. To solve this problem, there is a need to compensate for the lost reactive power. Several researchers have proposed various approaches to mitigate this problem such as thyristor switched capacitor bank, series compensator, series reactor, series var compensator (SVC), Static Synchronous Compensator (STATCOM), synchronous condenser and others. In order to further draw attention in this area, this work investigates a number of research papers on power compensation techniques and draw up challenges from each work that can be considered for further investigation. To this end, each research paper reviewed is evaluated in terms of problem solved, technique used, and results obtained. It therefore offers ample opportunities for researchers to explore in improving power quality and power system safety.

Risk-based redispatch optimization is proposed as a methodology to support the Transmission System Operator (TSO) with preventive remedial actions obtained by extending the security constrained unit commitment/economic dispatch with constraints resulting from the risk assessed for the power system. Although being heuristic, the methodology is based on comprehensive dynamic security assessment as time-domain simulations are used, allowing to express the degree of all types of instabilities, e.g., caused by contingencies, in monetary terms. Therefore, the risk is assessed as the expected value of the cost incurred by the TSO. Such approach forms a new pathway to including risk in planning procedures already used by TSOs. Results obtained for the IEEE39 dynamic power system, with costs assigned to load shedding and generator tripping due to single transmission lines short-circuits, are shown as a reference case.

This paper deals with the design, simulation and implementation of shunt hybrid compensator to maintain the power quality in 3-phase distribution networks feeding different types balanced and unbalanced nonlinear loads. The configuration of the compensator consists of a selective harmonic elimination passive filter, a series connected conventional 6-pulse IGBT inverter, acting as the active filter terminated with a dc link capacitor. The theory and modelling of the compensator based on current harmonic components at the load end and their decomposition in d-q axis frame of reference are utilized in the reference current generation algorithm. Accordingly, the source current waveform is made to follow the reference current waveform using a high frequency carrier based controller. Further, this inner current control loop is supported by a slower outer voltage control loop for sustaining desirable dc link voltage. Performance of the compensator is evaluated through MATLAB simulation covering different types of loads and reduction of harmonic currents and THD at the supply side along with excellent regulation of dc link voltage are confirmed. The performance of a hybrid compensator designed and fabricated using the above principles is evaluated and corroborated with the simulation results.

Integration of wind energy into the grid faces a great challenge regarding power quality. The International Electrotechnical Commission (IEC)~61400-21 standard defines the electrical characteristics that need to be assessed in a Wind Turbine (WT), as well as the procedure to measure the disturbances produced by the WT. One of the parameters to be assessed are voltage fluctuations or flicker. To estimate the flicker emission of a Wind Power Plant (WPP), the standard establishes that a quadratic exponent should be used in the summation of the flicker emission of each WT. This exponent was selected based on studies carried out in WPPs with type I and II WTs. Advances in wind turbines technology have reduced their flicker emission, mainly thaks to the implementation of power electronics for the partial or total management of the power injected into the grid. This work is based on measurements from a WPP with 16 type III WTs. The flicker emission of a single WT and of the WPP were calculated. Low flicker emission values at the Point of Common Coupling (PCC) of the WPP were obtained. The flicker estimation at the PCC, based on the measurement from a single WT, was analyzed using different exponents. The results show that a cubic summation performs better than the quadratic one in the estimation of the flicker emission of a WPP with type III WTs.

While microcredits are, by the development practitioners, repeatedly hailed as a useful measure of development policy, this empirical research in Bangladesh arrives at different results: the governing and disciplinary measures are necessary to trigger the best possible repayment success. Based on interviews with the microfinance beneficiaries, loan officers, and microfinance experts in Bangladesh, I chart some of the most frequently used governing and disciplinary techniques including fictitious proximity of loan officers, their fields of visibility and surveillance processes. The “success” of credit delivery is a neoliberal stance that ensures the ceaseless debt repayment process using the intentional and planned conduct, capitalizing social capital and credit honour reputation, surveillance over business enterprises, use of equivocal language and different forms of deception. The development strategy through microfinance in Bangladesh is a development “dispositif” with a changing shift in its declared social missions.

The Power Theory of Exchange and Money (PTEM) refines the economic neoclassical two-equation model of exchange. PTEM replaces the statistical average condition of exchange, which represents the equality of supply and demand for all transactions in the market, with a more specific equation of the equality of the generalized power of the parties in relation to their objects of exchange. The purpose of the article is to show the application of PTEM for the study of various social phenomena. Along with a brief summary of the main statements of this theory, its integration into the existing corpus of theories and ideas in economics and sociology is considered. The conclusions of power theory are then applied to consider the following topics: the objective motivation of exchange by the desire to increase power, the power nature of market equilibrium, the power nature of money, the accumulation of power through profit, the creation of money as a power act, the role of the state in the creation of money, the measure of power as a possible tool for social and political research.

Computer systems that operate in remote locations such as satellites, remote weather stations and autonomous robots are highly limited in the availability of energy for their operation. This work aims to employ artificial intelligence algorithms in energy management in order to obtain the maximum energy yield and the prediction of energy availability to the system. The work presents the main types of algorithms used in artificial intelligence and presents the creation of a prototype that will operate as a low power system powered by batteries and a small solar plate, the prototype will perform inferences on the LSTM neural network algorithm in order to predict the future availability of energy, consequently the management system will carry out the energy distribution in order to obtain the maximum operation of the prototype without total discharge of the batteries. So that the artificial intelligence system could be embedded in the prototype, the TensorFlow Lite framework was used, which allows the inference to be carried out in devices with low consumption and limited processing power.

One of the challenges posed by renewable energies is the stabilization of parameters related to the quality of electrical energy. This study demonstrates the existence of a relationship between input blocks of hydropower and the variation of the fundamental frequency of the electricity grid. By mapping production data provided by Spanish Electric Network with frequency measured in the laboratory, it is shown that gradients of hydropower are correlated with frequency fluctuations for certain characteristic times. Considering hourly instances of energy input, the study compares two methods for calculating hydropower gradients (linear regression and pseudo-linear regression); and two methods for calculating local frequency extremes (the "specular inertia" method and analysis by comparison with the moving average), in order to corroborate the results.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

This paper discusses recent developments in creep, over a wide range of temperature, that mqy change our understanding of creep. The five-power law creep exponent (3.5 to 7) has never been explained in fundamental terms. The best the scientific community has done is to develop a natural three power-law creep equation that falls short of rationalizing the higher stress exponents that are typically five. This inability has persisted for many decades. Computational work examining the stress-dependence of the climb rate of edge dislocations we may rationalize the phenomenological creep equations. Harper-Dorn creep, “discovered” over 60 years ago has been immersed in controversy. Some investigators have insisted that a stress exponent of one is reasonable. Others believe that the observation of a stress exponent of one is a consequence of dislocation network frustration. Others believe the stress exponent is artificial due to the inclusion of restoration mechanisms such as dynamic recrystallization or grain growth that is not of any consequence in the five power-law regime. Also, the experiments in the Harper-Dorn regime, which accumulate strain very slowly (sometimes over a year) may not have attained a true steady state. New theories suggest that absence or presence of Harper-Dorn may be a consequence of the initial dislocation density. Novel experimental work suggests that power-law breakdown may be a consequence of a supersaturation of vacancies which increase self-diffusion.

In this paper a variable’s involved in assessing the quality of a distributed generation system are reviewed, aiming to minimize the electric power losses (unused power consumption) and optimize the voltage profile. To provide this assessment, several experiments have been made to the IEEE 34-bus test case and various actual test cases with the respect of multiple DG units. The possibility and effectiveness of the proposed algorithm for optimal placement and sizing of DG in distribution systems have been verified. Finally, four algorithms were trailed: simulated annealing (SA), hybrid genetic algorithm (HGA), genetic algorithm (GA) and variable neighbourhood search. The HGA algorithm was found to produce the best solution at a cost of longer processing time.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well-suited for mass-production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we use a polynomial taper profile optimization algorithm to design 1×2 and 2×2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best performing 1×2 and 2×2 power splitters have 20 μm and 16 μm coupling lengths, respectively. Our designs have minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across 9 different chips show excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1×2 and 2×2 adiabatic optical power splitters have excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements show greater than 20 dB extinction ratios over 130 nm bandwidth. We also demonstrate the design of 1×2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%.

Proper management of solar energy, as an effective renewable source, is of high importance toward sustainable energy harvesting. This paper offers a novel sophisticated method for predicting solar irradiance (SIr) from environmental conditions. To this end, an efficient metaheuristic technique, namely electromagnetic field optimization (EFO) is employed for optimizing a neural network. This algorithm quickly mines a publicly available dataset for non-linearly tuning the network parameters. To suggest an optimal configuration, five influential parameters of the EFO (i.e., N_Pop, R_rate, Ps_rate, P_field, and N_field) are optimized by an extensive trial and error practice. Analyzing the results showed that the proposed model can learn the SIr pattern and predict it for unseen conditions with high accuracy. Furthermore, it provided about 10% and 16% higher accuracy compared to two benchmark optimizers, namely shuffled complex evolution and shuffled frog leaping algorithm. Hence, the EFO-supervised neural network can be a promising tool for the early prediction of SIr in practice. The findings of this research may shed light on the use of advanced intelligent models for efficient energy development.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

A supply chain management (SCM) system is a strategic cooperative that organically integrates all supply chains to improve the performance of a company. The greatest critical success factor of SCM is partnership. Without cooperation between companies, SCM performance is limited. Does this imply, therefore, that companies within the supply chain can achieve mutual transactions equally? If the power between companies is unequal, how does this affect their partnership? The focus of this study is to assess whether power types enhance SCM performance through partnerships. We categorize power types as mediated and non-mediated. Mediated power is categorized based on coercion, reward, and legitimate, while non-mediated power is categorized based on information, expert, and reference. Therefore, this study examines how power types form a causal partnership relationship within the supply chain, and performs an empirical investigation on how the partnerships influence SCM performance.

In this paper, new N-way Wilkinson power dividers (WPDs) are represented by using slow-wave structures such as narrow slits loaded and meandered transmission lines. The slit loaded and meandered lines are used to represent the quarter wavelength transmission lines of a conventional WPD for size reduction. Based on the proposed approaches, 2-, 4- and 8-way power dividers are designed, simulated and fabricated. The fabricated -, 4- and 8-way circuits have been measured at the center frequencies of 2.03, 1.77, and 1.73 GHz in an excellent agreement with the predicted ones. The meandered transmission lines are also used to design new types of WPDs having novel input/output port arrangements. For this purpose, two 3-way WPDs are located at both sides of the same board so as to have different power splitting ratios at different inputs and outputs to provide alternative solutions for antenna arrays. Furthermore, a 5-way dual layer WPD is introduced by locating the meandered transmission lines to two layers. The proposed 3- and 5-way WPDs allow halving the input power at the next output port in the order of P/2, P/4, P/8, P/16, and P/16. All of the designed power halving WPDs have been simulated, fabricated and successfully tested.

In the development of power systems it is indicated very often, that transformation of power systems should be carried out in accordance with the idea of energy democracy. This will develop energy communities, that are trying to meet energy needs by using local renewable generation sources. This may result with a temporary low load on the MV lines connecting the community grid and the power system. Such state may cause incorrect operation of power protection systems. This can cause an extended protection operation time, due to decision algorithms inactivity at low values of measurement currents. Therefore, the detailed MV lines overcurrent digital protection model and a dynamic model of the power network were developed. The simulation results are showing that the settings of the parameters activating the protection decision algorithms affect their operation time in dynamic conditions. The conclusion is that the development of the power protection automatics must be carried out in the same time (preferably in advance) with the change of the power system operation model. This is very important for future power systems with high penetration energy communities and renewable generation sources.

A decade ago, non-radiative wireless power transmission reemerged a promising alternative to deliver electrical power to devices where a physical wiring proved to be unfeasible. However, conventional coupling-based approaches are neither scalable nor efficient when multiple devices are involved, as they are restricted by factors like coupling and external environments. Zenneck waves are excited at interfaces, like surface plasmons and have the potential to deliver electrical power to devices placed on a conducting surface. Here, we demonstrate, efficient and long range delivery of electrical power by exciting non-radiative waves over metal surfaces to multiple loads.Our modeling and simulation using Maxwells equation with proper boundary conditions shows Zenneck type behavior for the excited waves and are in excellent agreement with experimental results. In conclusion, we physically realize a radically different power transfer system, based on a wave, whose existence has been fiercely debated for over a century.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.

To quantitatively estimate the risk of power system operation under extreme rainfall, a multi-scenario stochastic risk assessment method is proposed. First, a scenario generation scheme considering waterlogged faults of power facilities is constructed based on the storm water management model (SWMM) and the extreme learning machine method. These scenarios will be merged to several typical scenario sets for further processing. The outage of power facilities will induce power flow transfer which may consequently lead to transmission lines’ thermal limit violation. Semi-invariant and Gram-Charlier level expansion methods are adopted to analytically depict the probability density function and cumulative probability function of each line’s power flow. The optimal solution is performed by a particle swarm algorithm to obtain proper load curtailment at each bus, and consequently the violation probability of line thermal violations can be controlled within an allowable range. The volume of load curtailment as well as their importance are considered to quantitatively access the risk of power supply security under extreme precipitation scenarios. The effectiveness of the proposed method is verified in case studies based on the IEEE 24-bus system.

The local reactive power control in distribution grids with a high penetration of distributed energy resources (DERs) is essential in future power system operation. Appropriate control characteristic curves for DERs support stable and efficient distribution grid operation. However, the current practice is to configure local controllers collectively with constant characteristic curves that may not be efficient for volatile grid conditions or the desired targets of grid operators. To address this issue, this paper proposes a time series optimization-based method to calculate control parameters, which enables each DER to be independently controlled by an exclusive characteristic curve for optimizing its reactive power provision. To realize time series optimizations, the open-source tools pandapower and PowerModels are interconnected functionally. Based on the optimization results, Q(V)- and Q(P)-characteristic curves can be individually calculated using the linear decision tree regression to support voltage stability and provide reactive power flexibility and potentially reduce grid losses and component loadings. In this paper, the newly calculated characteristic curves are applied in two representative case studies, and the results demonstrate that the proposed method outperforms the reference ones suggested by grid codes.

Harmonic resonances are part of the Power Quality (PQ) problems of electrified railways and have serious consequences for the continuity of service and integrity of components in terms of overvoltage stress. The interaction between Traction Power Stations (TPSs) and trains that causes line resonances is briefly reviewed showing the dependence on infrastructure conditions. The objective is real-time monitoring of resonance conditions seen first of all from the onboard panto-graph interface, but it is equally applicable at TPS terminals. Voltage and current spectra, and de-rived impedance and power spectra, are analyzed proposing compact and efficient methods based on Short-Time Fourier Transform, suitable for real-time implementation with the hardware avail-able for energy metering and harmonic interference monitoring. The methods are tested by sweeping long recordings taken at some European railways, covering cases of longer and shorter supply sections, with a range of resonance frequencies of about one decade. They give insight into the spectral behavior of resonances, their dependency on position and change over time, and criteria to recognize genuine infrastructure resonances from rolling stock emissions.

This paper proposes a method based on genetic algorithm (GA) for the security-constrained optimal dispatch of integrated natural gas and electricity networks, considering operating scenarios in both energy systems. The mathematical formulation of the optimization problem consists of a multi-objective function which aims to minimize both cost of thermal generation (diesel and natural gas) as well as the production and transportation of natural gas. The joint gas-electricity system is modeled by two separate groups of nonlinear equation, which are solved by the combination of Newton's method with the GA. The applicability of the proposed method is tested in the Belgian gas network integrated with the IEEE 14-bus test system and a 15-node natural gas network integrated with the IEEE 118-bus test system. The results demonstrate that the proposed method provides efficient and secure solutions for different operating scenarios in both energy systems.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

A closed form solution for the common and differential modal currents induced on a pair of infinitely long parallel conductors by a voltage source was derived. For lossy conductors the current consists of a continuous spectrum of radiation modes and (for the common mode) a modified low loss Sommerfeld-Goubau mode and (for the differential mode) a quasi-TEM mode. This model is used to investigate the influence of a parallel conductor on microwave power line communication systems. For typical parameters, it is shown that the performance of these systems can be enhanced.

The decarbonization of the electrical energy sector is in progress for contrasting the climate changes, with a relevant increase of the Renewable Energy Sources (RES) power plants, mostly in Dispersed Generation (DG). The adequacy and the security of power systems, with a huge penetration of RES in DG is possible with a suitable integration of energy storage. In fact, energy storages are able to provide many different services for long-term adequacy and real time security. In this framework the present paper deals with a Thermal Energy Storage (TES) proposed for power system services. The technology presented is made up of modules containing a bed of fluidizable solid particles, which can store thermal energy from waste heat, process heat and/or from electricity. Stored thermal energy can be released, e.g. as superheated steam, for thermal uses or converted into electricity, by means of steam turbines. Some possible applications are then reported explaining advantages and limits.

This paper provides an optimization strategy for flexible operation at the system level, so as to guide the real-time flexible ramping of the power grid. Firstly, the concept of regional power grid flexibility was clarified, and the ramping factor is proposed as a flexibility metric. On this basis, taking the output priority of each node as the objective function and considering constraints such as line flow, power balance, and system flexibility, a mathematical model for regional power grid transmitting flexible power externally is proposed. Compare with the traditional models, this model focuses more on flexibility rather than economy. The case analysis based on the improved IEEE 30-Bus System verifies the feasibility and effectiveness of the proposed strategy and its advantages over the traditional models.

Wireless communications are gaining massive demand for faster video streaming, virtual reality, and 5G-based IoT (Internet of Things) applications. Due to this network congestion increases hastily. The demand for user-specific services, machine learning, forcing the radio access network (RAN) to provide improvement in utilization of spectrum efficiency, minimizing power consumption, and improving data rate. For LTE/LTE-A network specifications provided by third-generation partnership project (3GPP), guarantees to provide qualitative of service (QoS). Release 15/16 utilizes two-dimensional (2D) active antenna array systems (AAS). This kind of AAS provides beam forming in both azimuth and elevation also termed as Full Dimensional MIMO (FD-MIMO). It enhances the radiation pattern of the antenna array element by adjusting the angular power spectra at the base station (BS), it also allows selecting the minimum number of antennas for effective beam forming toward specific user equipment’s (UEs). Spectrum allocation challenge can be dealt with at mm wave band having FR2 (>6GHz) frequency band specified by International Telecommunication Union (ITU-R) in line with IMT-2020 specifications. The spectrum is free at mm Wave for communication of 5G. However, the main challenge is, it faces path loss and atmospheric loss electromagnetic energy absorbed by gases like oxygen. In this work, the 5G new RAN power spectrum and power delay profile at 10GHz carrier frequency with 20MHz to 100MHz channel bandwidth is observed for line of sight (LOS) and non-line of sight (NLOS) communication for guaranteed QoS. To demonstrate the path loss and power delay profile (PDP) in directional and Omni-directional antennas NYUSIM channel simulator is utilized.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

In this paper, the power quality of interconnected microgrids is managed using a Model Predictive Control (MPC) methodology which manipulates the power converters of the microgrids in order to achieve the requirements. The control algorithm is developed for the microgrids working modes: grid-connected, islanded and interconnected. The results and simulations are also applied to the transition between the different working modes. In order to show the potential of the control algorithm, a comparison study is carried out with classical Proportional-Integral Pulse Width Modulation (PI-PWM) based controllers. The proposed control algorithm not only improves the transient response in comparison with classical methods but also shows an optimal behavior in all the working modes, minimizing the harmonics content in current and voltage even with the presence of non-balanced and non-harmonic-free three-phase voltage and current systems

Let be a power function $f_{r,M}(s)$ defined for every $s$ within the finite set $M$ as follows $$f_{r,M}(s)= \begin{cases} s^r, \ &s\in M,\\ 0, \ &\mathrm{otherwise}. \end{cases} $$ Let a discrete convolution of $f_{r,M}(s)$ be denoted as follows $\mathrm{Conv}_{r,M}[n]=(f_{r,M}*f_{r,M})[n]$. Let a real coefficients $A_{m,j}$ be given by the following recurrence $$ A_{m,j} = \begin{cases} 0, & \mathrm{if } \ j<0 \ \mathrm{or } \ j>m, \\ (2j+1)\binom{2j}{j} \sum_{d=2j+1}^{m} A_{m,d} \binom{d}{2j+1} \frac{(-1)^{d-1}}{d-j} B_{2d-2j}, & \mathrm{if } \ 0 \leq j < m, \\ (2j+1)\binom{2j}{j}, & \mathrm{if } \ j=m. \end{cases} $$ In this paper we show that for every $n>0$ the following odd-power identities involving coefficients $A_{m,j}$ and convolution transform $\mathrm{Conv}_{r,M}[n]$ hold $$ \begin{split} n^{2m+1}+1&=\sum_{r=0}^{m}A_{m,r}\mathrm{Conv}_{r,\mathbb{N}}[n],\\ n^{2m+1}-1&=\sum_{r=0}^{m}A_{m,r}\mathrm{Conv}_{r,\mathbb{Z}_{>0}}[n],\\ n^{2m+1}&=\sum_{r=0}^{m}A_{m,r}\sum_{k=1}^{n} k^r(n-k)^r\\ &=\sum_{r=0}^{m}A_{m,r}\sum_{k=0}^{n-1} k^r(n-k)^r. \end{split} $$

Concern about the planet's future has motivated governments around the world to adopt policies that promote more responsible energy consumption. Reducing emissions of the principal cause of climate change man-made greenhouse gases requires greater system efficiency and the utilization of renewable energy sources. The generation of electricity is the single largest source of hazardous pollutants, followed by the transportation sector. This is true due to the extreme reliance on petroleum and its derivatives that these industries have. Electric mobility is receiving more attention from businesses, governments, and academic institutions as a means to reduce the negative impacts of current energy consumption. Without measures to address common technical issues, electric vehicles would strain electrical infrastructure. In order to determine the best strategy for switching operations and feeder reconfiguration, this research presents a helpful hybrid genetic algorithm particle swarm optimization (HGAPSO) method. Meet transmission limits while decreasing real power losses and enhancing the system's bus voltage profile. The effects of HGAPSO on power losses and voltage distributions in the network are analyzed. Then, a report is produced contrasting GA and PSO. This cross-breeding of GA and PSO led to HGAPSO. This important problem can be solved more effectively with the use of new or improved algorithms. To find the optimal reconfiguration and properly rearrange transmission network interconnection, it employs a plethora of heuristic optimization algorithms. The objective is to limit bus voltage variations while maintaining the system's radial topology and minimizing power usage. The reliability and performance of the procedure were evaluated using MATLAB's IEEE 33-bus communication network. The outcomes demonstrate the effectiveness of the proposed technique, which cuts down on power waste during standalone runs and speeds up the processing time.

Mobile robots can perform tasks on the move, including exploring terrain, discovering landmark features or moving a load from one place to another. This group of robots is characterized by a certain level of intelligence allowing making decisions and responding to stimuli received from the environment. As part of Industry 5.0, such mobile robots and humans are expected to co-exist and work together in a shared environment to make human work less tiring, quicker, and safer. This can only be realized when clean, dense, and economical energy sources are available. The aim of the study is to analyze the state of the art and to identify the most important directions for future developments in robotic power systems based mainly on batteries. The efficiency and performance of the battery depends on the design using different materials. Work environments and performance requirements are considered in this systematic review to classify solutions that help developers choose the best suited power system for specific application. Indirectly, the aim of the work is to generate discussion within the scientific and engineering community. A narrative review of publications from six major bibliographic databases according to preset inclusion criteria was combined with a critical analysis of current and future technologies. The main findings of the review allow answering question what is the role of modern power source technologies, artificial intelligence and ground-breaking research work in global policies related to energy saving, green policies, and sustainable development. The main opportunities and threats are discussed, and a brief feasibility analysis is carried out. Novelty of the article relates not only to the analysis of technologies, but also to approaches and their use under conditions of limited resource availability, when resource usage must be minimized. The article provides an overview of batteries, their specifications, classifications, and their advantages and disadvantages. In addition, we propose: (1) an algorithm for selecting main energy source for robot application, and (2) an algorithm for selecting electrical system power supply. Current mobile robot batteries are, in most cases, their biggest limitation. Progress in batteries development is too slow to catch up with the demand for robot autonomy and range requirements, limiting the development of mobile robots. Further intensive research and implementation work is needed to avoid years of delay in this area.

One of the most crucial and economically beneficial tasks for energy customer is peak load curtailment. On account of the fast response of renewable energy resources (RERs) such as photovoltaic (PV) units and battery energy storage system (BESS), this task is closer to be efficiently implemented. Depends on the customer peak load demand and energy characteristics, the feasibility of this strategy may warry. When adaptive neuro-fuzzy inference system (ANFIS) is exploited for forecasting, it can provide many benefits to address the above-mentioned issues and facilitate its easy implementation, with short calculating time and re-trainability. This paper introduces a data driven forecasting method based on fuzzy logic for optimized peak load reduction. First, the amount of energy generated by PV is forecasted using ANFIS which conducts output trend, and then, the BESS capacity is calculated according to the forecasted results. The trend of the load power is then decomposed in Cartesian plane into two parts, left and right from load peak, searching for BESS capacity equal. Network switching sequence over consumption is provided by a fuzzy logic controller (FLC) with respect to BESS capacity and PV energy output. Finally, to prove the effectiveness of the proposed ANFIS-based peak shaving method, offline digital time-domain simulations have been performed on a real-life practical test micro grid system in MATLAB/Simulink environment and the results have been experimentally verified by testing on a practical micro grid system with real-life data obtained from smart meter and also, compared with several previously-reported methods.

Penetration of grid connected inverters (GCI) has arisen in power systems due to increasing integration of renewable sources. However, restrictive grid codes require that renewable sources connected to the grid with power electronic systems must be properly connected and appropriate currents must be injected to support stability of the grid under grid faults. Simultaneous injection of symmetrical positive and negative sequence currents is mandatory to support stabilization of grid at the instant of grid faults. Conventional synchronously rotating frame dq current controllers are insufficient under grid faults due to low bandwidth of PI controllers. This paper proposes a new grid current control strategy for grid connected voltage source inverters under unbalanced grid voltage conditions. A proportional current controller with a first order low pass filter disturbance observer (DOb) is proposed which establishes positive sequence power requirements and independently control negative sequence current components under unbalanced voltage conditions. The method does not need any parameter, since it estimates nonlinear terms with low pass filter DOb. Simulations are implemented in Matlab/Simulink platform demonstrating the effectiveness of proposed method.

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

Improving performance and promoting sustainability in women's handball are key objectives to maximize the potential of female players and ensure the long-term viability of the sport. In this context, training with Olympic movements and their derivatives improves the development of strength, power, and speed, which are determinants of performance in team sports. The aim of this study was to determine if training with Olympic movements produces significant improvements in jumping, throwing, sprinting, and change of direction performance in women handball players. Twenty-one female handball players participated in the study (10 for the control group and 11 for the intervention group). Age ranged from 15 to 17 years. All participants performed four assessment tests (Abalakov Test, throw test, 20-meter Sprint and V-Cut Test) to determine jump height, throwing speed, running speed, and change of direction ability. Measurements were carried out before and after the intervention. For six weeks, the control group performed the strength work established by the club twice a week while the intervention group additionally performed training with Olympic movements. Significant differences (p &lt;0.05) were found between the pre and post measurement of the control group and the intervention group in jump height, throwing speed and running speed, being higher in the intervention group. For the change of direction, no significant differences were found. Between groups, significant differences were observed at the end of the intervention for jump height and running speed. The conclusion of this study was that, by training with Olympic movements, in addition to regular training, could produce greater improvements in jumping performance, throwing speed and running speed in female handball players.

This article presents a proposed system that enables energy transfer from the dc grid to a single-phase onboard grid, operating at an hi frequency. In addition to the energy transfer function, it additionally enables compensation of reactive power in the ac grid when the converter operates at less than rated power. To operate in compensator mode, it is necessary to decouple the current from the grid into active and reactive components and control them independently. To achieve good dynamics, synchronizers that operate in the dq system are used. In the case of a single-phase grid, it requires such a synchronizer to generate virtual quadrature signals. The used systems based on second-order generalized integrator are good, but to improve dynamics in the work a quadrature generator based on trigonometric calculations was proposed. The developed system was implemented in a proportional resonant current control system. Tests performed in steady state and in dynamic states related to typical grid disturbances showed better dynamic properties than the standard integrator-based system.Keywords: power transfer; compensator; P+R controller

The design of highly efficient sensitizers is one of the most significant areas in dye-sensitized solar cell (DSSC) research. We have studied a series of benzothiadiazole-based D-π-π-A organic dyes, putting emphasis on the influence of the donor moiety on the DSSC’s efficiency. Using linear response time-dependent density functional theory (TDDFT) with the CAM-B3LYP functional different donor groups were characterized in terms of electronic absorption spectra and key photovoltaic parameters. As a reference a dye has been considered which has a benzothiadiazole fragment linked via thiophene rings to a diphenylamine donor and a cyanoacrylic acid acceptor. The different systems are first studied in terms of individual performance parameters, which are eventually aggregated into the power conversion efficiency. Here only the amino-substituted species shows a modest increase, whereas the dimethylamino case even shows a decrease.

The growing need to use renewable sources and the current difficulty in spreading the electricity grid in a widespread manner raise the question of how to respond to the need for more electricity immediately. The idea behind this study is to power a horizontal axis wind turbine with the air flow generated for cooling a stationary internal combustion engine. The power extracted from this solution is significantly lower than that of the internal combustion engine (about 0.3%) and could be advantageous only in limited contexts. Installation costs are limited because many elements deriving from wind variability can be removed or simplified.

This study analyzes the correlation between the lifetime and the rest energy of the unstable particle states with a lifetime greater than the zeptosecond (10⁻²¹ s), using data available from the Particle Data Group. This set of states seems to be divided into three groups, in each of which the two quantities can be correlated through a remarkably accurate power law. Although this fact does not represent anything new compared to the predictions of the Standard Model, it nevertheless reveals an unexpected order structure in the set of particle decays, emerging from such predictions.

We consider a control problem for a diffusive PDE model of heterogeneous population of thermostatically controlled loads (TCLs) aiming to balance the aggregate power consumption within a given amount of time. Using the Green’s function approach, the problem is formulated as an approximate controllability problem for a residue depending on control parameters nonlinearly. A sufficient condition for approximate controllability is derived in terms of initial temperature distribution, operation time of TCLs and threshold value of the aggregate power consumption. Case studies allow to reveal the advantages of the proposed solution from numerical calculations point of view.

Purposely slow velocity resistance exercise (i.e., 10 s concentric and eccentric phases) is a popular training method, but limits the loads that can be lifted (e.g., <50% 1 RM). This study compared the biomechanical properties of purposely slow velocity (SLOW) and traditional resistance exercise (TRAD) that uses maximal lifting velocities. Healthy resistance-trained men (n=5) performed two testing sessions (barbell squat and bench press) in random-order; a SLOW session (1 set x 10 repetitions at 28% 1 RM, 10 s concentric & eccentric), and a TRAD session (3 x 10 at 70% 1 RM, controlled eccentric and maximal concentric). A force plate and linear position transducer were used to collect kinetic and kinematic data for every repetition of both protocols (α = 0.05). For both exercises, both concentric and eccentric mean force (N) and power (W) for each repetition was greater for TRAD. When the entire training session (squat + bench press) was examined, SLOW exhibited greater time under tension, while TRAD produced greater work (J) and impulse (N·s). Contrary to suggestions in both the lay and scientific literature, purposely slow resistance exercise produced less force, power, and work than traditional velocity resistance exercise.

For the particular selected type of fractals, i.e., the Kronecker product based fractals, the introductory common classification is proposed. It essentially relies on the size and content of the initial fractal matrix. In turn, it gives one of the possible explanation of the phenomenal ability to produce a few of the most popular fractals using many different algorithms, languages and tools. Also, it paves the way to discover on the regular basis thousands of the new fractals, and this gives researchers a wider range of fractal models to choose from.

Ultralight power generation equipment has high requirements for the power density, continuous operation, and transient stability of the whole machine, and there is a direct conflict between high power density design and substantial stability control in the power unit design. In order to meet the power density requirements of ultra-light power stations, three main problems need to be solved, namely engine speed oscillation and flameout in the process of load power mutation, matching of the generator and engine torque, and stabilizing the voltage waveform of the AC output end. In this paper, we proposed an exquisite control strategy for ultralight power generation systems in engines, generators, and inverters. The effectiveness and practicability of the proposed strategy are verified by both simulation and experiment. The results show that the proposed control strategy can effectively solve the instability problem of the ultralights generator set and improve the stability of the system, where the response recovery can be achieved within 0.9 seconds under the condition of total load increase or decrease, and the mismatching degree of the generator following the engine is reduced by 90%. The strategy could also guarantee long-term stable operation with high-quality electrical energy output.

Comparisons of power flows and efficiencies in two structurally quite similar cylindrical series-parallel planetary gear systems (PGSs) were performed in three separate parts of this paper. Each of these single degree of freedom (DoF) systems consists of three different 2KH subsystems connected in series-parallel. The main goal was to prove that apart from complex, structurally and dynamically coupled PGSs, there are also complex and only structurally coupled PGSs, in which the phenomenon of power flow circulation inside closed loops does not occur. Such a half-coupled type of PGS is herein called pseudo-coupled. Therefore, Part I discusses in detail the geometry, kinematics and statics of coupled PGSs in order to determine power flow paths. A comparison of the directions of power flow in both types of PGSs can be made in Part II after determining the power flow paths in the second planetary gear in a similar way. The directions of power flow in both types of PGSs were determined in a relatively simple way, thanks to the distinction between active and passive torques and thus active and passive shafts of individual subsystems. The efficiency comparison made in Part III will show whether power circulation has an influence on the efficiency value, at least in these two types of PGSs.

Keeping the bus voltage within acceptable limits depends on dispatching reactive power. Power quality improves as a result of creating an effective power flow system, which also helps to reduce power loss. Therefore, Optimal Reactive Power Dispatch (ORPD) studies aim at designing appropriate system configurations to enable a reliable operation of power systems. Establishment of such a configuration is handled through control variables in power systems. On the other hand, installing Distributed Generation Unit (DGU) into a power system can have an important effect on power quality and power loss minimization. In this paper, Grey Wolf Optimization (GWO method is applied to ORPD problem for the first time, to find optimal placement of newly installed DGUs at the power system. Active power loss and voltage minimization have been minimized by optimizing the control variables while keeping them within their upper and lower bounds, and by finding the optimal placement of a newly installed DGU in power system. On the basis of IEEE 30 bus and IEEE 118 bus systems, performance of the suggested approach is investigated. A comparison is also performed among the proposed method and some other methods. Test results demonstrate that the resulting configuration contributes to growing the rate of renewable integration to a power system. The results also indicate that the suggested optimization approach applied to ORPD problem has improved power system performance in terms of both on power loss and voltage deviation. The promising results highlight the potential of the GWO algorithm to facilitate the integration of renewable power sources, and its role in promoting sustainable energy solutions.

The environmental issues we are currently facing require long-term prospective efforts for sustainable growth. Renewable energy sources seem to be one of the most practical and efficient alternatives in this regard. Understanding a nation's pattern of energy use and renewable energy production is crucial for developing strategic plans. No previous study has been performed to explore the dynamics of power consumption with the change in renewable energy production on a country-wide scale. In contrast, a number of deep learning algorithms demonstrated acceptable performance while handling sequential data in the era of data-driven predictions. In this study, we developed a scheme to investigate and predict total power consumption and renewable energy production time series for eleven years of data using a Recurrent Neural Network (RNN). The dynamics of the interaction between the total annual power consumption and renewable energy production are investigated through extensive Exploratory Data Analysis (EDA) and a feature engineering framework. The performance of the model is found satisfactory through the comparison of the predicted data with the observed data, visualization of the distribution of the errors and Root Mean Squared Error (RMSE) value of 0.084. Higher performance is achieved through the increase in the number of epochs and hyperparameter tuning. The proposed framework can be used and transferred to investigate the trend of renewable energy production and power consumption and predict the future scenarios for different communities. Incorporation of the cloud-based platform into the proposed pipeline may lead to real-time forecasting.

Presently power control and management play a vigorous role in information technology and power management. Instead of non-renewable power manufacturing, renewable power manufacturing is preferred by every organization for controlling resource consumption, price reduction and efficient power management. Smart grid efficiently satisfies these requirements with the integration of machine learning algorithms. Machine learning algorithms are used in a smart grid for power requirement prediction, power distribution, failure identification etc. The proposed Random Forest-based smart grid system classifies the power grid into different zones like high and low power utilization. The power zones are divided into number of sub-zones and map to random forest branches. The sub-zone and branch mapping process used to identify the quantity of power utilized and the non-utilized in a zone. The non-utilized power quantity and location of power availabilities are identified and distributed the required quantity of power to the requester in a minimal response time and price. The priority power scheduling algorithm collect request from consumer and send the request to producer based on priority. The producer analysed the requester existing power utilization quantity and availability of power for scheduling the power distribution to the requester based on priority. The proposed Random Forest based sustainability and price optimization technique in smart grid experimental results are compared to existing machine learning techniques like SVM, KNN and NB. The proposed random forest-based identification technique identifies the exact location of the power availability, which takes minimal processing time and quick responses to the requestor. Additionally, the smart meter based smart grid technique identifies the faults in short time duration than the conventional energy management technique is also proven in the experimental results.

The work addresses the problem of Power Quality (PQ) metrics (or indexes) suitable for DC grids, encompassing Low and Medium Voltage applications, including electric transports, all-electric ships and aircrafts, electric vehicles, distributed generation and microgrids, modern data centers, etc. The two main pillars on which such PQ indexes are discussed and built are: i) the physical justification, so the electric phenomena affecting DC grids and components (PV panels, fuel cells, capacitors, batteries, etc.), causing e.g. stress of materials, ageing, distortion, grid instability; ii) the existing standardization framework, pointing out desirable coverage and extension, similarity with AC grids standards, but also inconsistencies. The first point is made more clear and usable by a graphical overview of the discussed phenomena. On this basis PQ is interpreted beyond the usual low-frequency range, including thus supraharmonics and common-mode disturbance, and filling the gap with the Electromagnetic Compatibility domain. However, phenomena typical of EMC and electrical safety (such as various types of overvoltages and fast transients) are excluded. Suitable PQ indexes are then reviewed, suggesting integrations and modifications, to cover the relevant phenomena and technological progress, and to better follow the normative exigencies.

The development of small scale hydroelectric power plants in Norway is determined by natural conditions, policies, attitudes and property rights. The owner of the river is the central decision maker. It is he who decides whether he will develop the power plant himself, Whether he wants to enter into a contract with an external investor and let him develop the power plant, whether he will sell his property rights or postpone the decisions. All available choices will involve risk. In order for him to make the best choice he must find the certainty equivalent to each of the choices and choose the one with the highest certainty equivalent. This is the first time the utility theory of John von Neumann and Oskar Morgenstern has been applied to decision makers in the hydro power industry in Norway.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

This paper studies a multihop amplify-and-forward (AF) simultaneous wireless information and power transfer (SWIPT) relaying system. Each relaying node harvests energy using power splitting (PS) scheme from a part of its received signal to amplify and forward the rest the received signal to the next relay. Based on this system model and signal flow, we derived and solved the convex energy minimization problem with optimal PS ratio. The influence of processing cost was then investigated for the AF-SWIPT system with the decode-and-forward SWIPT as benchmark, where AF-SWIPT was found to be superior.

Power converter technologies have become increasingly vital in various applications due to their efficient management of electrical energy. With the growing prominence of renewable energy sources like solar and wind, the high penetration of power electronic converters has been justified. However, ensuring power quality has emerged as a significant challenge for grid-connected power converters. The divergence from the ideal sinusoidal waveform in terms of magnitude and frequency impacts both grid-side currents and voltages. Several studies have proposed solutions to address power quality issues at the load side. The advancement of power converters has been fueled by the development of high-performance microprocessors and the emergence of high-speed switching devices, such as SiC-MOSFETs. This paper focuses on the design of voltage source converters, particularly those based on SiC-MOSFET semiconductor devices. The article presents the design of H-Bridge cells, discusses two-level voltage source converters based on cascade H-Bridge cells in parallel configuration with experimental fault analysis, addresses the seven-level voltage source converters topology, and explores the design and experimental results of the matrix converter. The findings underscore the importance of considering the entire converter design for improved performance at high switching frequencies. The article concludes by summarizing the main outcomes and implications of this research.

This paper presents a new methodology to evaluate the performance of an electric vehicle hybrid power system consisting of a fuel cell and a supercapacitor. The study compares the results with those obtained for a battery-electric vehicle. The methodology extends to three driving modes, ECO, NORMAL, and SPORT, corresponding to conservative, moderate, and aggressive acceleration, and three driving conditions, low, medium, and high energy demand. We develop a simulation process to evaluate the energy consumption and the energy rate of a specific electric vehicle used as a prototype for the study. The methodology applies to a driving route that includes acceleration, deceleration, braking, and constant speed segments reproducing standard driving conditions in urban journeys. The proposed method considers combined driving modes, ECO, NORMAL, and SPORT, in each acceleration process, with variable fractions, 0% to 100%, for each mode. This methodology optimizes the simulation results as it fits the current driving way in urban environments. The simulation results show an average reduction in energy consumption of 37% and 27.1% in vehicle weight, contributing to lower energy use. The study concludes that using a hybrid power system, fuel cell/supercapacitor, instead of a battery in electric vehicles is beneficial, especially in journeys with frequent acceleration processes.

This work investigates how to balance the electricity supply and demand in a carbon-neutral northern Europe. Applying a cost-minimizing electricity system model including options to invest in eleven different flexibility measures, cost-efficient combinations of strategies to manage varia-tions are identified. The results of the model are post-processed using a novel method to map the net load before and after flexibility measures are applied to reveal the contribution of each flexi-bility measure. The net load is mapped in the space spanned by the amplitude, duration, and number of occur-rences. The mapping shows that, depending on cost structure, flexibility measures contribute to reduce the net load in three different ways; 1) by reducing variations of long duration but low amplitude, 2) by reducing variations of high amplitude but short duration and low occurrence or 3) by reducing variations of high amplitude, short duration and high occurrence. It is found that cost-efficient variation management is achieved by combining wind and solar power and by combining strategies (1-3) to manage variations. The cost-efficient combination of strategies de-pends on electricity system context where electricity trade, flexible hydrogen and heat production (1) manage the majority of variations in regions with good conditions for wind power while sta-tionary batteries (3) are the main contributors in regions with good conditions for solar power.

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performance proves that the system is suitable for a given range of boundary conditions from a thermodynamic standpoint, as well as in terms of system complexity and technical feasibility. New possibilities with regard to added power production have the potential to improve the economics and promote the use of absorption chiller systems.

High-penetration of Distributed Energy Resources (DER) in low voltage distribution grids, mainly photovoltaics (PV), might lead to overvoltage in the point of common coupling. Volt-VAr is one of the common control functions for DER power converters used to enhance the stability and the reliability of the voltage in the distribution system and, thus, fulfilling the network operator requirements. In this study, a centralized algorithm will provide local Volt-VAr control parameters to each PV inverter, based on the electrical grid characteristics where each equipment is installed. Since accurate information of grid characteristics is typically not available, the parametrization of the electrical grid is done using power meter data in DER location and a voltage sensitivity matrix. The algorithm has different optimization modes to both minimize voltage deviation and line current. In order to validate the effectiveness of the algorithm and its deployment in real infrastructure, it has been tested in an experimental setup with PV emulators in a set of 5-day tests. Volt-VAr control algorithm successfully adapted its parameters based on grid topology and PV inverter characteristics, achieving a voltage reduction up to 25% of the allowed voltage deviation.

The operation of electricity and natural gas transmission networks in the U.S. are increasingly interdependent, due to the growing number of installations of gas fired generators and the penetration of renewable energy sources. This development suggests the need for closer communication and coordination between gas and power transmission system operators in order to improve the efficiency and reliability of the combined energy system. In this paper, we present a co-simulation platform for examining the interdependence between natural gas and electricity transmission networks based on a direct current unit-commitment and economic dispatch model for the power system and a transient hydraulic gas model for the gas system. We analyze the value of day-ahead coordination of power and natural gas network operations and show the importance of considering gas system constraints when analyzing power systems operation with high penetration of gas generators and renewable energy sources. Results show that day-ahead coordination contributes to a reduction in curtailed gas during high stress periods (e.g., large gas offtake ramps) and a reduction in energy consumption of gas compressor stations.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Synchronization is a prerequisite for the stability of electrical energy, which is the cornerstone of a functioning society. Identifying whether generators are synchronized or not has been attracting immense research interest. Utilizing synchronized stability boundaries can strongly simplify stability discrimination. However, fundamental issues such as determining accurate stability boundaries remain challenging. In this study, an accurate synchronized stability boundary equation that is independent of the system and disturbances is presented, and it is applicable to an arbitrarily coupled grid. The special structure induced by spontaneous synchronization appears to be only near the stability boundary. The results of this study show that: the synchronous stability boundary is an intrinsic property of the system, independent of its structure and parameters. Synchronization on the network may be independent of the network. These conclusions will challenge the traditional perception of synchronization on networks, and the synchronization stability of the grid can be analyzed in a uniform way.

Geothermal energy is likely to be a significant contributor in achieving sustainable energy goals and net-zero emissions targets. Within geothermal power plants, heat exchangers play a critical role in harnessing this renewable energy source. However, these heat exchangers encounter significant challenges when exposed to geothermal fluids, including erosion, corrosion, and scaling, which adversely affects their performance and longevity. The current review focuses on surface engineering techniques, particularly coatings, as a highly effective and economically viable solution to address these challenges in geothermal heat exchangers. The review begins by providing an overview of geothermal energy, its significance in the context of sustainability and the important role played by heat exchangers in geothermal power generation, followed by the challenges and their impact on heat exchangers. The subsequent section focuses on surface engineering by coatings and its types employed to enhance the performance of heat exchangers. In the final part, the reader is presented with an overview of the challenges associated with the application of coatings in geothermal heat exchangers and potential future directions in this field. This review offers a detailed understanding of the critical role coatings play in improving the efficiency and service life of heat exchangers in geothermal power plants.

In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the delta-sigma modulator, consumes a significant amount of power in active summing, although it can achieve perfect summation. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. The objective of this article is to explore how to achieve perfect summation in a passive manner. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A pseudo 3-order delta-sigma modulator based on 4-bit quantizer is designed to verify the scheme. Simulation results show that at a supply voltage of 1.2V and a bandwidth of 20kHz, the SNDR reaches 102.62dB, power consumption is only 148.32μW, and Schreier FoM of SNDR is 183.92dB.

This book review addresses the contribution of Tim Marshall’s “The Power of Geography”. The purpose of this essay is to highlight the significant role of geography in shaping political landscapes, alliances, and global affairs through the book review. What is new about this essay is its accessible presentation of complex geopolitical concepts, making it a valuable resource for students of geography and readers interested in global politics. Through the analysis of case studies and historical background, the book illuminates the interplay between physical landscapes, territoriality, and power dynamics. The findings highlight the continuing influence of geography on nations, regional identities, and the evolving global order.

Detection of partial discharge (PD) activities in high-voltage equipment can be done according to the several mechanisms of signal detection, which are electromagnetic wave signal detection, acoustic signal detection, chemical reactions, electrical signal detection, or optical emission detection. Recently, multiple methods of detection and localization of partial discharge activities occurred in power transformers and gas-insulated switchgear (GIS) have been proposed to monitor the health condition of high-voltage equipment, especially when the awareness regarding preventive maintenance has been emphasized at the industrial level and electrical providers. In aligning the needs of industrial and the improvement of PD detection methods, this manuscript focused on reviewing the current practice methods for the detection and localization of PD signals in high-voltage equipment and comparing their efficacy, in summarizing the future direction of research work-related methods of PD detection. The comparative reviews are discussed in terms of the mechanism of PD signal detection, indication parameters, calibration technique, advantages, and limitations of each method of PD measurement in detail.

Teaching and learning a new language is a complex process that requires more than just memorizing vocabulary and grammar rules. Immersing oneself in the target language's culture and history is essential for achieving fluency and accuracy. In recent years, researchers have explored the potential of music as a tool for language learning. This paper discusses the benefits of using music in language learning, including improved listening comprehension, pronunciation and fluency, and cultural understanding. The theoretical framework of sociocultural theory, cognitive load theory, and task-based language learning is presented to support the use of music in language learning. This paper also provides practical recommendations for learners to incorporate music into their language learning routine, as well as resources for finding music in the target language, such as online music platforms and language learning apps. The article concludes by encouraging language learners to incorporate music into their language learning routine and providing resources for finding music in the target language, such as online music platforms and language learning apps. Overall, this paper demonstrates that music can be a powerful and enjoyable tool for enhancing language learning outcomes.

Polarons, quasiparticles resulting from the interaction between an impurity and the collective excitations of a medium, play a fundamental role in physics, mainly because they represent an essential building block for understanding more complex many-body phenomena. In this manuscript, we study the spectral properties of a single impurity mixed with identical bosons in a one-dimensional lattice with power-law hopping. In particular, based on the so-called T-matrix approximation, we show the existence of well-defined quasiparticle branches for several tunneling ranges and for both, repulsive and attractive impurity-boson interactions. Furthermore, we demonstrate the persistence of the attractive polaron branch when the impurity-boson bound state is absorbed into the two-body continuum and that the attractive polaron becomes more robust as the range of the hopping increases. The results discussed here are of relevance for the understanding of the equilibrium properties of quantum systems with power-law interactions.

Methane is the main cause of sewer explosion accidents, and the available monitoring methods mainly use portable gas sensors for on-site detection. However, these methods cannot grasp the dynamic changes in methane in a sewer in real time or make better predictions of methane explosion accidents. Here, we present a low-power online monitoring system for sewer methane in order to ensure the safety of urban sewers. A low-power ultrasonic gas sensor was used to monitor the methane content in biogas. Due to the impacts of changes in CO2, temperature, and humidity in the sewer on the ultrasonic methane measurement results, a corresponding compensation method was proposed. The effectiveness of the compensation method was verified through experiments, which measured the methane concentration under different influences, and the methane values measured before and after compensation were compared. The power consumption was only 1.28 mW if the system worked in intermittent operation mode, and it could operate for about 1.5 years by selecting a lithium battery with a capacity of 5 A · H. The experimental results showed that the gas detection accuracy could meet the commercial requirements and had a high compensation for the impacts of carbon dioxide, temperature, and humidity.

Dysregulation of high-frequency neuronal oscillations has been implicated in the pathophysiology of schizophrenia. Chronic methamphetamine (METH) use can induce psychosis similar to paranoid schizophrenia. The current study in mice aimed to determine the effect of chronic METH treatment on ongoing and evoked neuronal oscillations. C57BL/6 mice were treated with METH or vehicle control for three weeks and implanted with extradural recording electrodes. Two weeks after the last METH injection, mice underwent three EEG recording sessions to measure ongoing and auditory-evoked gamma and beta oscillatory power in response to an acute challenge with METH (2mg/kg), the NMDA receptor antagonist MK-801 (0.3mg/kg), or saline control. A separate group of mice pretreated with METH showed significantly greater locomotor hyperactivity to an acute METH challenge, confirming long-term sensitisation. Chronic METH did not affect ongoing or evoked gamma or beta power. Acute MK-801 challenge reduced ongoing beta power whereas acute METH challenge significantly increased ongoing gamma power. Both MK-801 and METH challenge suppressed evoked gamma power. Chronic METH treatment did not modulate these acute drug effects. There were minor effects of chronic METH and acute METH and MK-801 on selected components of event-related potential (ERP) waves. In conclusion, chronic METH treatment did not exert neuroplastic effects on the regulation of cortical gamma oscillations in a manner consistent with schizophrenia, despite causing behavioural sensitisation.

Modern exchange theories model a large market, but do not explain single exchange. The paper considers the phenomenon of single exchange and formulates the general exchange problem in the form of a system of two equations, subjective and objective. Subjective equilibrium is given by the Walras-Jevons marginal utility equation. Objective equilibrium equations by Walras and Jevons are averaged over all transactions in the market and can only give a rough general picture without explaining the specific price of an individual exchange. An exchange micro-condition must be found that, when averaged, will give the Walras market equilibrium macro-condition. The study of the internal structure of exchange leads to the need to consider power. The concept of generalized power is introduced. It is generalized power that serves as the primary comparable and measurable objective basis of exchange. The power theory of exchange provides the objective price-equation. It is demonstrated that money is a measure of generalized power in exchange and a certification of generalized power in subsequent exchanges. The proposed theory is able to uniformly explain any exchange, including a single one, which is impossible with the existing theories of exchange.