Solid particle cationic polyacrylamide (CPAM) is one of the most commonly used organic polymer flocculants in oilfield wastewater treatment, but there are some problems, such as slow dissolution rate, and easy to form a "fish-eye" in the process of diluting into aqueous solution. However, the current liquid CPAM products also have some problems, such as low effective content, poor storage stability, degradation in a short time and high preparation cost. In this paper, a secondary processing technology of solid particle CPAM was studied, and a CPAM suspension was successfully prepared. This suspension has an effective content of 50.00%, No separation in 7 days of storage at room temperature, no separation in 30 min of centrifugation at a speed of 2000 r/min, and diluted to a 0.40 % weak gel solution in just 16.00 min. For 1000 NTU of diatomite simulated wastewater, the optimal turbidity removal rate of the suspension was 99.50%, which was higher than the optimal turbidity removal rate of 98.40% for the inorganic flocculant polymeric aluminum chloride (PAC). For oil and gas field oily wastewater, the optimal turbidity removal rate of CPAM suspension was 35.60%, which was higher than the optimal turbidity removal rate of 28.40% for solid particle CPAM.

Following the general aim of recapitulating the native mechanical properties of tissues and organs in vitro, the field of materials science and engineering has benefited from recent progress in developing compliant substrates with similar physical and chemical properties. In particular, in the field of mechanobiology, soft hydrogels can now reproduce the precise range of stiffnesses of healthy and pathological tissues to study the mechanisms behind cell response to mechanics. However, it was shown that biological tissues are not only elastic but also relax at different timescales. Cells can indeed perceive and actually need this dissipation because it is a critical signal integrated with other signals to define adhesion, spreading and even more complicated functions. The mechanical definition of hydrogels used in mechanobiology is however commonly limited to the elastic stiffness (Young’s modulus) and this value is known to depend greatly on the measurement conditions that are rarely reported. Here, we report that a simple relaxation test performed under well defined conditions can provide all the necessary information to characterize soft materials mechanically, by fitting the dissipation behavior with a generalized Maxwell model (GMM). The method was validated using soft polyacrylamide hydrogels and proved to be very useful to unveil precise mechanical properties of gels that cells can sense and offer a set of characteristic values that can be compared with what is typically reported from microindentation tests.

Large-scale volumetric fracturing is generally used during shale gas development. The return rate of fracturing fluid is low, and a large amount of slickwater will be retained in the reservoir. The adsorption and desorption of partially hydrolyzed polyacrylamide (HPAM), an additive commonly used in slickwater, on the surface of shale was studied using Longmaxi Shale from the Sichuan Basin. The experimental results showed that the mass ratio of the HPAM solution to shale reached saturation adsorption at 20:1 when the concentration of HPAM solution was 1000 mg/L and 25:1 when the concentration of HPAM solution was 500 mg/L. The mass ratio of the HPAM solution to shale was fixed at 25:1, and the adsorption equilibrium was reached at a HPAM concentration of 1000 mg/L when the aqueous solution temperature was 30°C and 800 mg/L when the aqueous solution temperature was 60°C. The Langmuir adsorption model yielded a better fit than the Freundlich adsorption model. The adsorption equilibrium time at 30°C was at 60 min for a HPAM concentration of 500 mg/L, while for a concentration of 1000 mg/L, it was at 90 min. The adsorption equilibrium time at 60°C was 40 min for a HPAM concentration of 500 mg/L, whereas it was 60 min for a HPAM concentration at 1000 mg/L. The pseudo-second order kinetics model yielded better fits than the pseudo-first order kinetics model. The adsorption of HPAM on shale was strong, and the adsorbed HPAM resembled cobwebs adhering to the shale surface. HPAM on the surface of shale after adsorption could resist the desorption capacity of water. However, when the amount of adsorbed HPAM on shale increased significantly, the amount of residual HPAM on the surface of the shale decreased rapidly during desorption in deionized water. The desorption of HPAM on the shale surface followed a modified desorption model. The higher the concentration of HPAM adsorbed on the shale surface was, the easier it was to desorb, the easier it was to be removed from the shale.

EOR is a process that helps maximize recoverable oil reserves, extend field life and increase recovery rates, and is an important tool for companies to maintain production and increase return on investment. In this article, the performance of nanoclay on aqueous phase viscosity, wettability, and recycled oil in core fluidization in polyacrylamide nanofluid has been investigated in different experiments and EOR. We have used polymers due to the properties of polymers in increasing rheology and effective mobility and controlling stability and variability to resume growth oil in nanofluids. Adding 5% by weight of salt to polymer-clay nanofluid has also been investigated in samples comparable to pure nano clay without salt. The viscosity of this suspension increases by about 50% by adding a certain amount of salt. If the same amount of salt is added to the polymer diluent, the viscosity decreases drastically. The results of the wettability test also show that clay has a better potential to change the wettability in the tendency to salt. In core fluidization tests, the highest efficiency of 30% was obtained in the third recycling in the combination of clay nanoparticles and sulfone copolymer. The highest efficiency was obtained in the third scenario in core fluidization tests, that is; A combination of resin nanoparticles and sulfone copolymer. Their detailed behavior in the characteristics of wettability, rheology, and core fluidization is analyzed in this article.

A delayed crosslinked polymer gel was developed for indepth water control in mature oilfields. The thermal gelation behavior of nonionic polyacrylamide (NPAM) and PEI was investigated, and sodium citrate (NaCit) was selected as a new retarder to prolong the gelation time. The gelation performance of NPAM/PEI gel system can be adjusted by the variation of NPAM or PEI concentration, and a quadratic model was developed by statistical analysis, which predict the gelation time of NPAM/PEI gel system. The obtained model showed high significance and good reliability as suggested by the F-ratio of 175.16 and high adjusted R-square value (0.9732). The decrease of the initial pH value of gelling solution leads to the weaker gel viscosity and longer gelation time due to the protonation of amine groups on the PEI chains. Increasing temperature resulted in higher gel viscosity but shorter gelation time. The addition of NaCit showed a good delayed gelation effect on the NPAM/PEI gel system, and the gel system in the presence of NaCit exhibited a good compatibility with injected and formation water. A dense three-dimensional structure was observed in matured NPAM/PEI/NaCit gel, and it could keep stable below 150℃. The gel system could effectively reduce the permeability (>95%) and restricted the flow of water after matured in natural cores.

Burkholderia andropogonis is a severe plant pathogen that can infect more than 50 plant species. Although its genome has been sequenced and annotated, various mechanisms underlying its physiology and pathogenicity remain unknown. Some of these mechanisms can be uncovered through understanding its proteome. In this study, sodium dodecyl polyacrylamide gel electrophoresis (SDS-PAGE) and mass spectrometry analysis were used to profile the proteome of B. andropogonis. Exactly 538 proteins, which belong to 190 protein families performing 88 different functions were identified. The resulting STRING network analysis identified 28 proteins having highly connected interactions with adenosine triphosphate (ATP)-binding-cassette and (ABC) transport system. To the knowledge of the authors, this is the first comprehensive proteomic study on B. andropogonis.

To provide carbon steel a long corrosion protection effect in NaCl solution with various pH, a pH-controlled intelligent inhibitor based on poly-acrylamide (PAM) and oleate imidazoline (OIM) was synthesized. SEM, FT-IR and TGA results indicating the OIM inhibitor was successfully loaded into PAM hydrogel with a very high content (39.64 wt%). The OIM release behavior from hydrogel structure have two stages, quickly release and sustained release. The pH of solution could affect the initial release kinetics of OIM inhibitor and the diffusion path in hydrogel structure. Weight loss measurement of L80 steel in different pH solution with OIM@PAM proved the inhibitor responsive release mechanism and an-ti-corrosion performance. The inhibition efficiency of OIM@PAM can maintain over 80% after long term immersion in harsh corrosive environment (pH 3), which is much higher than the inhibition efficiency of inhibitor in moderate corrosive solution.

Polyphosphate (polyP) accumulating organisms (PAOs) are the key agent to perform enhanced biological phosphorus removal (EBPR) activity, and intracellular polyP plays a key role in this process. Potential associations between EBPR performance and the polyP structure have been suggested, but are yet to be extensively investigated, mainly due to the lack of established methods for polyP characterization in the EBPR system. In this study, we explored and demonstrated that single-cell Raman spectroscopy (SCRS) can be employed for characterizing intracellular polyPs of PAOs in complex environmental samples such as EBPR systems. The results, for the first time, revealed distinct distribution patterns of polyP length (as Raman peak position) in PAOs in lab-scale EBPR reactors that were dominated with different PAO types, as well as among different full-scale EBPR systems with varying configurations. Furthermore, SCRS revealed distinctive polyP composition/features among PAO phenotypic sub-groups, which are likely associated with phylogenetic and/or phenotypic diversity in EBPR communities, highlighting the possible resolving power of SCRS at the microdiversity level. To validate the observed polyP length variations via SCRS, we also performed and compared bulk polyP length characteristics in EBPR biomass using conventional polyacrylamide gel electrophoresis (PAGE) and solution ³¹P nuclear magnetic resonance (³¹P-NMR) methods. The results are consistent with the SCRS findings and confirmed the variations in the polyP lengths among different EBPR systems. Compared to conventional methods, SCRS exhibited advantages as compared to conventional methods, including the ability to characterize in situ the intracellular polyPs at subcellular resolution in a label-free and non-destructive way, and the capability to capture subtle and detailed biochemical fingerprints of cells for phenotypic classification. SCRS also has recognized limitations in comparison with ³¹P-NMR and PAGE, such as the inability to quantitatively detect the average polyP chain length and its distribution. The results provided initial evidence for the potential of SCRS-enabled polyP characterization as an alternative and complementary microbial community phenotyping method to facilitate the phenotype-function (performance) relationship deduction in EBPR systems.

The mechanisms by which bacteriophage T4 converts the metabolism of its E. coli host to one dedicated to progeny phage production was the subject of decades of intense research in many labs from the 1950’s through the 1980’s. At this point, a wide range of phages are starting to be used therapeutically and in many other applications and also the range of available phage sequence data is skyrocketing. It is thus important to re-explore the extensive available data about the intricacies of the T4 infection process as summarized here, expand it to looking much more broadly at other genera of phages, and explore phage infections using newly-available modern techniques and a range of appropriate environmental conditions.

While significant efforts have been made to recycle metals like lithium or cobalt for sustainable development in the battery industry, other high-value materials in the renewable energy sector, such as fluorinated carbon nanotubes (FCNTs), have not been adequately explored for re-utilization after their quality has been downgraded. FCNTs are expensive and energy-intensive to produce, making their sustainable use crucial. This study explores the potential of reusing quality-downgraded fluorinated carbon nanotubes (QD-FCNTs) as eco-friendly nano-additives in microgel composites for water retention applications. By employing a surface treatment process that avoids additional energy costs and environmentally harmful chemicals, we successfully enhanced the interaction between QD-FCNTs and microgels. This treatment significantly improved water retention time by reducing rapid evaporation, enabling sustained water release. Our findings demonstrate a promising avenue for the sustainable application of quality-downgraded fluorinated carbon nanotubes in agricultural and environmental technologies.