We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

This paper is a thorough review of innovative architectures of electro-hydraulic servovalves that exploit actuation systems based on piezo-electric materials. The use of commercially available piezo-electric actuators, namely, piezo-stacks, amplified piezo-stacks, rectangular benders and ring benders, is very promising for the actuation of the main stages and of the pilot stages of servovalves, given the fast response and low weight of piezoelectric materials. The use of these actuators can also allow novel designs to be developed, thus helping manufacturers to overcome the typical drawbacks of commercial servovalves, such as the high complexity and the high internal leakage of the pilot stages of two stage servovalves, as well as the large size and weight of direct drive servovalves. Firstly, the piezoelectric actuators that can be used for driving servovalves are presented in the paper and their characteristics are thoroughly discussed. Then, the main novel architectures present in the literature are explained and compared with the commercial ones, and their performance parameters are discussed to draw conclusions on the prospect that some of these architectures can be used by manufacturers as future designs.

This paper provides a proof of concept for a linear electric generator that can be used to harvest energy from various sources of linear motion, such as vibrations, free-piston engines and wave energy. The generator can be used to power small electronic devices, such as sensors, or charge household batteries. Literature was reviewed to develop an understanding about the applications, control methods, excitation methods and mechanics of rotating and linear electric machines. A bidirectional, two-sided linear machine was designed with two stator cores and a single mover core. The stator windings and mover winding can be independently excited, allowing for three modes: no mover excitation, DC excited mover, and AC excited mover. Simulations results showed that the magnetic flux generated by DC excited stator cores were concentrated in the centre of the mover core. The use of two stator cores eliminates lateral flux in the mover core when it is not excited, minimising attraction and repulsion forces. Parametric analysis showed that flux cutting occurred in all operation modes, verifying that the generator will produce power when operating. Hardware tests produced an output current when the machine is electrically and mechanically excited, verifying the proposed design.

We present the prototype and analytical model of a miniaturized impact actuation mechanism, providing a fast out-of-plane displacement to accelerate objects against gravity, allowing for freely moving objects and hence for large displacements without the need of cantilevers. To achieve the necessary high speed, we chose a piezo electric stack actuator driven by a high-current pulse generator, connected to a rigid support and a rigid three-point contact with the object. We describe this mechanism with a spring-mass model and compare various inertial masses, all of them spheres, from different diameters and materials. As expected, we found that larger flight heights are achieved by harder projectiles, achieving, e.g., approx. 3 mm displacement for a 3 mm steel sphere using a 3x3x2 mm³ piezo stack.

PIEZO1 plays a crucial role in the human body as a mechanosensory ion channel. It has been demonstrated that PIEZO1 is important in tissue development and regulating many essential physiological processes. Studies have suggested that the PIEZO1 ion channel plays a role in invasion and progression in cancer; elevated levels of PIEZO1 have been correlated with increased migration in breast cancer cells, chemo-resistance and invasion in gastric cancer cells, and increased invasion of osteosarcoma cells. In addition, high PIEZO1 expression levels were correlated with a worse prognosis in glioma patients. On the other hand, studies in lung cancer have attributed high PIEZO1 levels to better patient outcomes. However, the clinical impact of PIEZO1 in breast cancer is not well characterized. Therefore, our goal was to determine the clinical relevance of PIEZO1 in breast cancer. Analysis of breast cancer data from The Cancer Genome Atlas (TCGA) was conducted to investigate PIEZO1 expression levels and correlation to survival, followed by validation in an independent dataset, GSE3494. We also performed gene set enrichment analysis (GSEA) and analyzed immune cell levels in breast tumors from TCGA through a CIBERSORT algorithm. Our results demonstrated that PIEZO1 expression levels are higher in hormone receptor (HR) negative than HR positive cohorts. High PIEZO1 expression is correlated with a significant decrease in survival in HR negative cohorts, suggesting that PIEZO1 could be utilized as a prognostic biomarker in HR negative breast cancer. GSEA showed that various signaling pathways associated with more invasive phenotypes and resistance to treatments, including epithelial-mesenchymal transition (EMT), hypoxia, and multiple signaling pathways, are enriched in high PIEZO1 HR negative tumors. Our results also demonstrated a decrease in CD8+ and CD4+ T cell infiltration in high PIEZO1 HR negative tumors. Further investigations are necessary to elucidate the mechanistic roles of PIEZO1 in HR negative breast cancer.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

The origin of an anomalous excess of high-energy (about 100 GeV and higher) positrons in cosmic rays is one of the rare problems in this field which is proposed to be solved with dark matter (DM). Attempts to solve this problem are faced with the issue of having to satisfy the data on cosmic positrons and cosmic gamma-radiation, which inevitably accompanies positron production such as FSR (final state radiation), simultaneously. We have been trying to come up with a solution by means of two approaches: making assumptions (*) about the spatial distribution of the dark matter, and (**) about the physics of its interactions. This work is some small final step of a big investigation regarding the search for gamma suppression by employing the second approach and a model with a doubly charged particle decaying into two positrons (X++→e+e+) is suggested as the most prospective one from those considered before.

Today, air quality is one of the global concerns that governments are facing. One of the main air pollutants is the particulate matter (PM) that affects human health. This article presents the modeling of a purification system by means of negative air ions (NAIs) for air pollutant removal, using computational intelligence methods. The system uses a high voltage booster output to ionize air molecules from stainless steel electrodes; its particle-capturing efficiency reaches up to 97%. With two devices (5 x 2 x 2.5 cm), 2 trillion negative ions are produced per second, and the particulate matter (PM 2.5) can be reduced from 999 to 0 mg / m3 in a period of approximately 5 to 7 minutes (in a 40 x 40 x 40 cm acrylic chamber). This negative ion generator is a viable and sustainable alternative to reduce polluting emissions, with beneficial effects on human health.

Cell-to-cell distant mechanical communication has been demonstrated by using in-vitro and in-vivo models. However, the molecular mechanisms underlying long-range cell mechanoresponsive interactions remain to be more elucidated. This study further examined the roles of α-Catenin and Piezo in traction force-induced rapid branch assembly of airway smooth muscle (ASM) cells on Matrigel hydrogel containing type I collagen. Our findings demonstrate that siRNA-mediated downregulation of α-Catenin or chemical inhibition of Piezo activity significantly reduced both cell directional movement and branching assembly. In regarding the role of N-cadherin in regulating branch assembly but not directional migration, our results further confirmed that siRNA downregulation of α-Catenin caused a remarked reduction of focal adhesion formation, as assessed by focal Paxillin and Integrin α5 localization. These observations implied that mechanosensitive α-Catenin was involved in both cell-cell and cell-matrix adhesions. Additionally, Piezo showed partial localization with Paxillin in focal adhesions, which was inhibited by α-Catenin downregulation with siRNA. This provides a plausible clue for Piezo mechanosensing traction force in the hydrogel. Collectively, our findings highlight the significance of α-Catenin in regulating cell-matrix interactions along with possible interpretation for Piezo mechanosensation at focal adhesions during cell-cell distant mechanical communication.

In the last decades synthetic jet actuators have gained much interest among the flow control techniques due to their short response time, high jet velocity and absence of traditional piping, that matches the requirements of reduced size and low weight. A synthetic jet is generated by the diaphragm oscillation (generally driven by a piezoelectric element) in a relatively small cavity, producing periodic cavity pressure variations associated with cavity volume changes. The pressured air exhausts through an orifice, converting diaphragm electrodynamic energy into jet kinetic energy. This review paper faces the development of various lumped-element models (LEMs) as practical tools to design and manufacture the actuators. LEMs can quickly predict device performances such as the frequency response in terms of diaphragm displacement, cavity pressure and jet velocity, as well as the efficiency of energy conversion of input Joule power into useful kinetic power of air jet. The actuator performance is analyzed also by varying typical geometric parameters such as cavity height and orifice diameter and length, through a suited dimensionless form of the governing equations. A comprehensive and detailed physical modeling aimed to evaluate the device efficiency is introduced, shedding light on the different stages involved in the process. Overall, the influence of the coupling degree of the two oscillators, the diaphragm and the Helmholtz’s one, on the device performance is discussed throughout the paper.

Pistol shrimps generate cavitation bubbles. Cavitation impacts due to bubble collapses are harmful phenomena, as they cause severe damage to hydraulic machineries, such as pumps and valves. However, cavitation impacts can be utilized for mechanical surface treatment to improve the fatigue strength of metallic materials, which is called “cavitation peening”. Through conventional cavitation peening, a cavitation is generated by a submerged water jet, i.e., a cavitating jet or a pulsed laser. The fatigue strength of magnesium alloy when treated by the pulsed laser is larger than that of the jet. In order to drastically increase the processing efficiency of cavitation peening, the mechanism of pistol shrimp (specifically when used to create a cavitation bubble), i.e., alpheus randalli, was quantitatively investigated. It was found that a pulsed water jet generates a cavitation bubble when a shrimp snaps its claws. Furthermore, two types of cavitation generators were developed, namely, one that uses a pulsed laser and one that uses a piezo actuator, and this was achieved by mimicing a pistol shrimp.

This study explores the feasibility of using an oscillating plate downstream of a cylindrical body to produce mechanical energy from a Von Kármán vortex street. The study aims to quantify the impact of the plate length, its separation from the cylinder, and a machine damping factor on the power coefficient and the blade’s displacement to identify the optimal configuration. This preliminary assessment assumes that the plate oscillation is small enough to avoid changes in the vortex dynamics. This assumption allows the construction of a surrogate model using CFD to evaluate the effect of plate length and separation from the cylinder on the fluctuating lift forces over the plate. Later, the surrogate model, combined with varying machine damping factors, facilitates the description of the device’s dynamics through the numerical integration of an angular momentum equation. The results showed that a plate with 0.52D length, 5.548D separation from the cylinder, and a damping factor of 0.013 achieved a power coefficient of 0.147 and a perpendicular displacement of 0.266D. These results demonstrate a substantial improvement in the performance of bladeless generators.

Solid tumours are characterized by an altered microenvironment (TME) from the physi-cochemical point of view, displaying a highly hypoxic and acidic interstitial fluid. Hy-poxia results from uncontrolled proliferation, aberrant vascularization and altered can-cer cell metabolism. Tumour cellular apparatus adapt to hypoxia by altering its metab-olism and behaviour, increasing its migratory and metastatic abilities by acquisition of a mesenchymal phenotype and selection of aggressive tumour cell clones. Extracellular acidosis is considered a cancer hallmark, acting as a driver of cancer aggressiveness by promoting tumour metastasis and chemoresistance by selecting for more aggressive cell phenotypes, although the underlying mechanism is still not clear. In this context, Ca2+ channels represent good target candidates due to their ability to integrate signals from the TME. Ca2+ channels are pH and hypoxia sensors and alterations in Ca2+ homeostasis in cancer progression and vascularization have been extensively reported. The present review will focus on Ca2+ permeable ion channels, with a major focus on TRP, SOC and PIEZO channels, that are modulated by tumour hypoxia and acidosis as well as the role of the resulted altered Ca2+ signals on cancer progression hallmarks. A deeper compre-hension of the Ca2+ signaling and acidic pH/hypoxia interplay will break new ground for the discovery of alternative and attractive therapeutics targets.

First of all the paper presents a solid solution of piezoelectric ceramic that was synthesized according to the general formula Pb(1-x)Srx(Ti0.48Zr0.52)(1-y)NbyO3 with x = 0.05 and y = 0.02, using wet ceramic processing technology and using an oxide mix as prime material. The effects of dopants (Sr2+ and Nb5+) on phase constitution, on microstructure and on the dielectric and piezoelectric properties were determinate. The Zr/Ti ratio was chosen near the morphotropic phase boundary of the PZT system in studied composition. The XRD data revealed that the PZT doped composition had tetragonal perovskite structure. Secondly the paper presents the design of the novel piezo-motor based on a surface wave which translates the linear extension of different piezoelectric segments of a piezoelectric cylinder into a rotational bending movement. This rotational bending of the piezoelectric cylinder is then transformed into a continuous rotation of the rotor through a calculated contact. The design of the motor takes advantage of the high piezoelectric constants of the developed material in an optimal way in order to increase the energetic efficiency. A brief mathematical model of electromechanical answer of piezoelectric materials is presented as it was used in the modeling of the material during the numerical simulations.

To gain insight into the differences between onshore and offshore atmospheric turbulence, 2 pressure fluctuations were measured for offshore wind under different environmental conditions. 3 A durable piezo-electric sensor was used to sample turbulent pressure data at 50 kHz. Offshore 4 measurements were performed at 100 m height on Germany’s FINO3 offshore platform in the 5 German Bight together with additional meteorological data provided by Deutscher Wetterdienst 6 (DWD). The statistical evaluation revealed that the stability state in the atmospheric boundary has a 7 large impact on turbulent fluctuations. Therefore, we used higher statistical properties (described 8 by so-called shape factors) to the stability state. Data was classified to be either within the unstable, 9 neutral or stable stratification. We found that in case of stable stratification, the shape factor is 10 mostly close to zero, indicating that a thermally stable environment produces closer-to Gaussian 11 distributions. Non-Gaussian distributions were found in unstable and neutral boundary layer states 12 and an occurrence probability was estimated. Possible impact on laminar-turbulent transition on the 13 blade is discussed with application of so-called laminar aerofoils on wind turbine blades. Use of a 14 cut-off frequency to separate load and aerodynamic turbulence is proposed.

Let $a, b$ and $n > 1$ be three positive integers such that $a$ and $\sum_{j=0}^{n-1} b^j$ are relatively prime. In this paper, we prove that the toric ideal $I$ associated to the submonoid of $\mathbb{N}$ generated by $\{\sum_{j=0}^{n-1} b^j\} \cup \{\sum_{j=0}^{n-1} b^j + a\, \sum_{j=0}^{i-2} b^j \mid i = 2, \ldots, n\}$ is determinantal. Moreover, we prove that for $n > 3$, the ideal $I$ has a unique minimal system of generators if and only if $a < b-1$.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

The Wind Energy Conversion System (WECS) plays an inevitable role across the world. In particular, the attention for Permanent Magnet Synchronous Generators (PMSGs) connected with wind farm is popular. This paper deals with the literature review that describes the recent advances, progresses and innovatory trends on PMSGs for WECS. Comparison between geared and direct-driven conversion systems and the classification of electrical machines used in WECS are discussed. A detailed analysis on the design aspects considering various topologies of PMSGs are encompassed in the literature. The PMSG design and optimization problems are solved by field computation techniques and optimized by using Soft Computing (SC) techniques .The three-dimensional, finite element software platform for the analysis and design of PMSGs is discussed. This paper also deals with the interdisciplinary modeling, analysis, and optimization of PMSG using Finite Element Analysis (FEM) and SC techniques. Finally, PMSGs are reviewed and compared for further exploration.

the intermittency and variability of these permeated Distributed Generators (DGs) could critically cause many security and economy risks to distribution systems. This paper applied a certain mathematical distribution to imitate the output variability and uncertainty of DGs. And then, four risk indices EENS, PLC, EFLC and SI were established to reflect the system risk level of distribution system. For the certain mathematical distribution of the DGs' output power, a developed PEM (point estimate method)-based method was proposed to calculate these four system risk indices. In this developed PEM-based method, enumeration method was used to list the states of distribution systems, an improved PEM was presented to deal with the uncertainties of DGs and the value of load curtailment in distribution systems was calculated by an optimal power flow algorithm. Finally, the effectiveness and advantages of this proposed PEM-based method for distribution system assessment were verified by the tests of a modified IEEE 30-bus system. Simulation results have shown that this proposed PEM-based method has a high computational accuracy and highly reduced computational costs compared with other risk assessment methods and is very effective for risk assessments.

This study explores the advanced integration of Bi2Te3-based thermoelectric systems in Ocean Thermal Energy Conversion (OTEC) to optimize performance. OTEC, a promising renewable energy source, needs help in efficiency maximization. We address this by implementing Bi2Te3 thermoelectric generators (TEGs), known for their high thermoelectric efficiency at low-temperature differences. Our research encompasses a comprehensive simulation and analysis of these TEGs in OTEC systems, examining material properties, system design, and environmental impact. We present a novel approach to integrating these TEGs, optimizing their arrangement, and interfacing with the OTEC cycle to enhance overall efficiency. The study also investigates the durability and cost-effectiveness of Bi2Te3 TEGs in marine environments. Results demonstrate a significant improvement in energy conversion efficiency, highlighting the potential of Bi2Te3 TEGs in sustainable ocean energy exploitation. This work advances material science in renewable energy, providing valuable insights into the practical application of thermoelectric materials in large-scale energy systems. It paves the way for future research on material optimization and system integration, essential for developing efficient and sustainable OTEC systems.

This research emphasizes a meta-heuristic Modified Ant Lion Optimizer (MALO) optimization approach for simultaneous utilization of DSTATCOM devices and distributed Photovoltaic (PV) sources with network reconfiguration in a radial power distribution scheme. In a radial power distribution network with network reconfiguration majority of the research is based on Constant Power model analysis. However, it is noticed that load models have a substantial impact on the distributed PV sources and the D-STATCOM device's optimal size and position. The effect of the Constant Power (CP) and Polynomial (ZIP) with load growth load models for the simultaneous insertion of distributed PV sources and DSTATCOM devices with network reconfiguration examined in this research work for power system planning. The penetration levels of distributed PV sources considered for the investigation are 25%, 50%, 75%, and 100%. The principal objective of this research is to reduce network total power losses, enhance the voltage magnitude profile at all buses, and reduce the overall operating cost while adhering to equality and inequality constraints. The proposed algorithm verified on 118-node test systems. The investigation is carried out for planning network upgradation to a High Voltage Distribution System(HVDS) on 317 nodes in the rural Bangalore Electricity Supply Company Limited(BESCOM) radial distribution scheme. Simulated results obtained by this method are validated with the BAT algorithm and available techniques in the literature.

An iterative outlier elimination procedure based on hypothesis testing, commonly known as Iterative Data Snooping (IDS) among geodesists, is often used for the quality control of the modern measurement systems in geodesy and surveying. The test statistic associated with IDS is the extreme normalised least-squares residual. It is well-known in the literature that critical values (quantile values) of such a test statistic cannot be derived from well-known test distributions, but must be computed numerically by means of Monte Carlo. This paper provides the first results about Monte Carlo-based critical value inserted to different scenarios of correlation between the outlier statistics. From the Monte Carlo evaluation, we compute the probabilities of correct identification, missed detection, wrong exclusion, overidentifications and statistical overlap associated with IDS in the presence of a single outlier. Based on such probability levels we obtain the Minimal Detectable Bias (MDB) and Minimal Identifiable Bias (MIB) for the case where IDS is in play. MDB and MIB are sensitivity indicators for outlier detection and identification, respectively. The results show that there are circumstances that the larger the Type I decision error (smaller critical value), the higher the rates of outlier detection, but the lower the rates of outlier identification. For that case, the larger the Type I Error, the larger the ratio between MIB and MDB. We also highlight that an outlier becomes identifiable when the contribution of the measures to the wrong exclusion rate decline simultaneously. In that case, we verify that the effect of the correlation between the outlier statistics on the wrong exclusion rates becomes insignificant from a certain outlier magnitude, which increases the probability of identification.

In pursuit of sustainable human survival, the effective utilization of renewable energy has become critical to technological advancement. Ocean Thermal Energy Conversion (OTEC) technology, which generates electricity by leveraging the temperature differential between surface and deep ocean waters, enables stable power generation around the clock. In this domain, the combination of thermoelectric generators (TEGs) and heat exchangers has exhibited immense potential for ameliorating the deficiencies of conventional OTEC. This study uses numerical simulation to investigate the fluid dynamics characteristics of heat exchangers with flat fins and different types of longitudinal vortex generators (LVGs) under the same number of fins. The research encompasses heat exchangers with rectangular, triangular, and trapezoidal LVGs. Concurrently, the analysis examines how the vortices generated by the LVGs influence the thermoelectric performance of the TEGs. The results demonstrate that heat exchangers integrating flat fins and LVGs can enhance the power generation efficiency of TEGs. However, the pumping power required by the LVGs constrains the thermoelectric conversion efficiency. Compared to rectangular and triangular LVGs, trapezoidal LVGs achieve a superior balance between output and pumping power. Heat exchangers utilizing trapezoidal LVGs can attain the highest TEG thermoelectric conversion efficiency with a specific seawater flow velocity. Overall, these findings provide valuable reference information for applying TEGs and heat exchangers in OTEC design.

Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.

In this paper, by extending some results of informational genomics, we present a new randomness test based on the empirical entropy of strings and some properties of repeatability and unrepeatability of substrings of certain lengths. We give the theoretical motivations of our method and some experimental results of its application to a wide class of strings: decimal representations of real numbers, roulette outcomes, logistic maps, linear congruential generators, quantum measurements, natural language texts, and genomes. It will be evident that the evaluation of randomness resulting from our tests does not distinguish among the different sources of randomness (natural, or pseudo-casual).

Load variations in any power system result in losses escalation and voltage drops. With the sensible and optimal allocation of distributed generators (DGs), these problems could be considerably mitigated. It has been seen in the priorly existing methods that ideally allocation of DGs has been carried out during fixed loads and constant power requirements. However, in real scenarios the loads are always variable and allocation of DGs must be done in accordance to the variations of the connected load. Therefore, the current paper addressed the aforementioned problem by distinctive optimal allocation of DGs for each variability of 24hour load horizon. However, the single exclusive solution is considered among all allocations of 24 hours. The min-max regret concept has been utilized in order to deal with such methodology. Altogether, 24 scenarios are analyzed wherein each scenario corresponds to a specific hour of the respective day. The optimal allocation of DGs in terms of their optimal sizing and placement has been carried out by using three algorithms including battle royal optimization (BRO), accelerated particle swarm optimization (APSO) and genetic algorithm (GA). The multi-objective optimization problem is evaluated on the basis of minimum value criterion of the multi-objective index (MO). MO comprises of active and reactive power losses and voltage deviation. Hence, in order to find robustness of proposed technique, Conseil international des grands réseaux electriques (CIGRE’s) MV benchmark model incorporating 14 buses has been considerably used as a test network. In the end the results of three proposed algorithms have been compared.

The term `motor control´ encompasses a wide range of mechanisms thought to be implicated in the organization of movements. Their study, like that of any other scientific field, must use specific notions to get to grips with them. This review is therefore organized along a series of notions that are frequently used in motor control, and we will discuss them with particular emphasis on neurological conditions, which may disrupt normal motor functioning. We will start with a short description of the roles of space and time, in which movements take place. Subsequently we will deal with kinematics and kinetics (dynamics) of movements. Then, we will list the inputs to motoneurons (MNs), which, in different forms, convey signals from the central nervous system (CNS) to skeletal muscles and muscle spindles, including central pattern generators (CPGs), sensory inputs and supraspinal descending fiber systems. Some helpers in movement organization will be introduced, such as internal models and neuronal network models. A relatively brief section on sensory-motor learning will follow because learning abilities are required to endow the sensory-motor system with flexibility and adaptability. The major emphasis is placed on neurological processes, which result from genetic modifications, autoimmune diseases, neurodegenerative diseases, infections in the nervous system as well as vascular and traumatic lesions. These neurological diseases lead to a variety of impairments and symptoms, particularly movement derangements including cerebellar ataxia, spasticity, and (other) movement disorders such as Parkinson’s syndromes. The conclusion is that there is no unique top controller that controls ´motor control`.

The complexity of modern power grids, exacerbated by integrating diverse energy sources, espe-cially inverter-based resources (IBRs), presents a significant challenge to grid operation and plan-ning since linear models fail to capture the intricate IBR dynamics. This study employs the Sparse Identification of Nonlinear Dynamics (SINDy) method to bridge the gap between theoretical un-derstanding and practical implementation in power system analysis. It introduces the novel Volterra-based Nonlinearity Index (VNI) to examine system-level nonlinearity comprehensively. The distinction of dynamics into first-order linearizable terms, second-order nonlinear dynamics, and third-order noise elucidates the intricacy of power systems. The findings demonstrate a fundamental shift in system dynamics as power sources transit to IBRs, revealing system-level nonlinearity compared to module-level nonlinearity in conventional syn-chronous generators. The VNI quantifies nonlinear-to-linear relationships, enriching our comprehension of power system behavior and offering a versatile tool for distinguishing between different nonlinearities and visualizing their distinct patterns through the proposed VIN profile.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

The thermoelectric generator (TEG) has much potential as a renewable energy technology that could be used in ocean thermal energy conversion (OTEC). This technique employs TEGs and heat exchangers as substitutes for the intricate elements found in conventional OTEC systems, including pressure valves, evaporators, condensers, and turbine generators. By harnessing the temperature difference between warm surface seawater and cold deep seawater, it facilitates the conversion of this thermal gradient into electrical energy. This study used computer simulations to look at and compare three different types of heat exchangers: a cavity-type heat exchanger, a heat exchanger with flat fins, and a heat exchanger with longitudinal vortex generators (LVGs). The objective was to evaluate the influence of these designs on the thermoelectric conversion performance when implemented in OTEC systems. The study's findings indicate that using heat exchanger configurations featuring flat fins, or LVGs, enhances the efficiency of thermal energy transfer from warm seawater to TEGs, resulting in a notable enhancement in the output power of TEGs. Furthermore, the efficiency of TEG thermoelectric conversion is influenced by varying seawater flow rates in relation to the performance of flat fins and LVGs. In contrast to the cavity-type heat exchanger, the utilization of a heat exchanger equipped with flat fins has been found to yield a notable enhancement in the output power of TEGs by approximately 22.92%. Furthermore, this configuration demonstrates a substantial improvement in thermoelectric conversion efficiency, exhibiting an increase of around 40.01%. These improvements are observed under certain conditions pertaining to flow rates and fin heights. Utilizing heat exchangers equipped with LVGs has been found to enhance the output power of TEGs by 13.02% and improve the overall thermoelectric conversion efficiency by 17.72%. These improvements are observed under certain conditions, including specific flow rates, LVG tilt angles, and locations.