The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

To obtain smooth coatings of TiO2 for building a new design of Ti-6Al-4V heart valve, the anodic oxidation technique in pre-spark conditions was evaluated. TiO2 coating is necessary for its recognize biocompatibility and corrosion resistance. A required feature on surfaces in contact with blood is a low level of roughness (Ra ≤ 50 nm) that not favor the formation of blood clots. The present paper compares the coatings obtained by anodic oxidation of the Ti-6Al-4V alloy using H2SO4 at different concentrations (0.1 M to 4 M) as electrolyte and applying different voltages (from 20 V to 70 V). Color and morphological analysis of coatings are performed using optical and scanning microscopy. The crystalline phases were analyzed by glancing X-ray diffraction. By varying the applied voltage different interference colors coatings were obtained. The differences in morphologies of the coatings, due to the change in concentration, are more evident at high voltages limiting the oxidation conditions for the desired application. Anatase phase was detected from 70 V for 1 M H2SO4. An increase in the concentration of H2SO4 decreases the voltage at which the transformation of amorphous to crystalline coatings occurs, i.e. with 4 M H2SO4 the anatase phase appears at 60 V.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.

The proton conductivity, phase composition and mechanical properties of (1-x)CsH2PO4–x fluoropolymer electrolytes (x-mass fraction, x=0-0.3) have been investigated firstly and discussed. UPTFE and PVDF-based polymers (F2M, F42, SKF26) with the high mechanical properties and thermal stability have been chosen as a fluoropolymer additive. According the XRD data, a monoclinic CsH2PO4 (P21/m) phase is retained in all compositions of the polymer electrolytes studied. The conductivity of (1-x)CsH2PO4-x fluoropolymer in the high-temperature phase decreases by approximately one order of magnitude compared with the pure CsH2PO4 for x~0.15-0.20. The size and shape of CsH2PO4 particles and their distribution have been shown to affect significantly the proton conductivity and mechanical properties of the membranes. The thin-film composite systems were produced by various methods of the obtaining salt particles, their mixing and applying to a polymer matrix. The uniform distribution of particles in the polymer systems with the size of ~300 nm was achieved by a pretreatment of the suspension in a bead mill. CsH2PO4-based mechanically strong membranes with the thickness ~50–100 μm were obtained for the soluble fluoropolymers (F2M, F42, SKF26). With an increase in the mass fraction of the polymer the ability of the membranes to resist the plastic deformation and the mechanical strength increases and comparable to the best low temperature membranes. The proton-conducting membranes (1-x)CsH2PO4 – x fluoropolymer with the optimal combination of the conductivity, mechanical and hydrophobic properties are promising for use in solid acid fuel cells.

Electrochemical Impedance Spectroscopy techniques were applied in this work to 9 lead-acid battery prototypes fabricated industrially, divided on three type/technology packages. Frequency dependent impedance changes were interpreted during successive charge/discharge cycles on two distinct stages: 1) immediately after fabrication; and 2) after a controlled aging procedure to 50% Depth of Discharge, following industrial standards. By investigating their State of Health behaviour vs electrical response, three methods were employed, namely the (Q-Q0) total charge analysis, the decay values of Constant Phase Element in the equivalent Randles circuits, and the resonance frequency of the circuit. A direct correlation has been found for prediction of the best performant batteries in each package, thus allowing a qualitative analysis capable to provide the decay of the battery State of Health. We emphasized which parameters are directly connected with their lifetime performance in both stages, and by consequence, which type/technology battery prototype emphasize the best performance. Based on this methodology, the industrial producers can further establish the quality of the novel batteries in terms of performance vs lifespan, allowing them to validate the novel technological innovations implemented in the current prototypes.

The lithium-ion batteries are widely used as a power source for portable devices, including cell phones. The useful life is about 2 years or 500 cycles, contributing to the generation of waste from electrical and electronic equipment (WEEE). Mining of lithium and cobalt damages the environment and is onerous; therefore, sustainable alternatives, such as obtaining these elements from secondary sources as recycling of lithium-ion batteries, are essential to provide the inputs used in the sector. However, the metallurgical route which will used to recovering them must be considered, due to this work aims for a more environmentally favorable process using DL-malic acid 1.5 M and instead of compared with sulfuric acid 2 M, heat pretreatment of 1 h and 3 h, and for all conditions, experiments were carried out with and without adding the oxidizing agent hydrogen peroxide. The best yields occurred in presence of H2O2 10 % v/v, and heat pretreatment of 1 h: 33.49 % Co and 4.63 % Li, and 29.78 % Co e 3.44 % Li were recovered by sulfuric acid and DL-malic acid, respectively.

This paper presents the use of Graph Neural Networks (GNNs) to predict the tensile strength of Fused Deposition Modeling (FDM) specimens. In the present work, there are four main input parameters i.e. Infill percentage, Layer height, Print speed and Extrusion temperature while the Tensile Strength is an output parameter were considered. This study includes use of central composite design based response surface methodology to finalize the experimental layout. 3D printed specimen were manufactured as per the ASTM E8 standard on FDM printer using Polylactic Acid (PLA) as filament. Micro-tensile test were performed on the printed specimen as per ASTM E8 standard. The GNN algorithm was trained on a dataset of FDM specimens, achieving a mean squared error (MSE) of 2.47, mean absolute error (MAE) of 1.14, and R-squared value of 0.78. An adjacency matrix, which shows the connections between nodes in a graph. The obtained plot for nodes and weights in a GNN provide valuable information about the model and its performance. The results show the potential of using GNNs in predicting the mechanical properties of additively manufactured specimens and provide a promising direction for further research in this field.

Lead Acid Batteries (LABs) are used for starting, lighting, and igniting, as well as in air conditioning systems and to supply power to electric engines in transport vehicles (TVs). However, the application of LABs for TVs has faced a number of market challenges, mounted by the upcoming high energy density and long lifespan batteries, such as lithium ion. LABs, on the other hand, are inexpensive. The key research question is, how can the lifespan of LABs used in automotive industries be increased, while still ensuring a low cost solution? Thus, integrating LABs with the supercapacitor (known as an electric double layer capacitor—EDLC) is likely to outperform the competing alternative batteries for TVs. This paper proposes a multiple stage approach to hybrid lead acid batteries and a supercapacitor system for TVs that is capable of maintaining the battery state-of-charge (SOC) at statistically high limits, ranging between 90% and 95%. This SOC target will likely ensure that the lifespan of the hybrid battery system can be elongated (extended) more than its competitors. In this study, the multiple stage approach of concatenated converters has been designed in order to satisfy all energy storage requirements for different characteristics of LABs and the supercapacitor. The designed hybrid system has been simulated using Matrix Laboratory (MATLAB/Simulink (version R2016a, MathWorks, Natick, MA, USA)). The simulated results show that high transient currents from the direct current (DC) bus of LABs, caused by the regenerative braking or deceleration of the TVs, reduce the battery lifespan and induce mechanical stress. The supercapacitor reduces the stress on the LAB by absorbing high transient currents. This, in turn, keeps the LABs’ SOC between 90% and 96% and the voltage at 12 V. As indicated by the simulated results, the hybrid battery SOC is maintained at 90–96% and the terminal voltage is approximately 12 V.

Accurate and efficient battery modeling is essential to maximize the performance of isolated energy systems and to extend battery lifetime. This paper proposes a battery model that represents the charging and discharging process of a lead-acid battery bank. This model is validated over real measures taken from a battery bank installed in a research center placed at “El Chocó”, Colombia. In order to fit the model, three optimization algorithms (Particle Swarm Optimization, Cuckoo Search, and Particle Swarm Optimization+Perturbation) are implemented and compared, being the last one a new proposal. This research shows that the model with the proposed algorithm is able to estimate and manage the real battery characteristics as SOC and charging/discharging voltage. The comparison between simulations and real measures shows that the model is able to absorb reading problems, signal delays, and scaling errors. The approach we present can be implemented in other types of batteries especially those used in stand-alone systems.

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

In this study, additive manufacturing of reinforced parts using metallic wire as both a reinforcement component and a shape memory stimulus through Fused Deposition Modeling (FDM) was investigated. A Shape Memory Polymer (SMP) restores its original shape and recovers it upon specific stimuli. This research employed chromium-nickel metal wire as a reinforcing component to enhance mechanical properties and introduce the capability for thermal stimulation of polylactic acid (PLA) via electrical current using the "in-situ impregnation" method within FDM process. Reinforced specimens were fabricated with wire with two diameters of 0.1 and 0.15 mm, along with two volume percentages of 5 and 10. Comprehensive evaluations encompassing mechanical (tensile and flexural) and thermal properties of the printed specimens were conducted. The outcomes revealed a significant enhancement in both tensile and flexural properties of the polymer matrix due to the embedding metallic wire, even under elevated temperatures during bending test. Furthermore, the thermal properties of the reinforced specimens were examined by subjecting them to various voltages, resulting in temperature ranging from 36.4 to 150.1°C. These findings highlight the ability to tailor a wide range of mechanical properties and shape recovery in the reinforced specimens by carefully selecting the wire volume fraction, voltage, and wire diameter, thus regulating the materials properties with specific application requirements.

Additive manufacturing (AM) are used in several industries such as automotive, aerospace, and medical sciences. One of the most common devices used in additive manufacturing is fused deposition modeling (FDM) 3D printers. This fabrication method has different inputs that affect the quality of the parts. In this research, the bending fatigue properties of polylactic acid (PLA) biomaterial made with a 3D printer are investigated. To demonstrate the influence of printing parameters on fatigue lifetime, standard specimens with nozzle diameters of 0.2-0.6 mm, extruder temperature of 180-240°C, and print speed of 5-15 mm/s were printed. After performing fully-reversed bending fatigue tests, it was found that printed specimens at 180°C have the best fatigue lifetime in most cases. Accordingly, fatigue behavior improved by reducing the nozzle diameter. Printing at lower temperatures also improved fatigue lifetime. The printing speed affected the slope of the S-N diagram, known as the fatigue strength exponent.

Background and objectives: This study were designed to determine uric acid concentration and renal histopathology of M. calabura L. stem bark extract in diabetic rats and to compare the natural product of M. calabura L. stem bark extract with allopurinol. Materials and Methods: A completely randomized design was used for the experiment which consisted of 6 treatment groups, each consisting of 4 rats, as follows: 1) NR, normal rat; 2) KN, diabetic rat (negative control); 3) KP, diabetic rats given allopurinol 10 mg/kg body weight; 4) EM150, diabetic rats given the test extract 150 mg/kg body weight/day; 5) EM300, diabetic rats given the test extract 300 mg/kg body weight/day; and 6) EM450, diabetic rats given the test extract 450 mg/kg body weight/ day. Results: The results showed that M. calabura L. stem bark extract decrease (p<0.05) uric acid levels in diabetic rats and no specific damage to renal proximal tubular cells was seen. Conclusions: It was concluded that M. calabura L. stem bark extract has a potential as an antihyperuricemic in diabetic rats. The recommended does was 300 mg/kg body weight to provide a significant effect on reducing the uric acid level in diabetic rats. Our findings support the use of this plant as a treatment for gout and other inflammatory diseases.

Two peat cores from two bogs were used to reconstruct high–resolution changes in atmospheric Pb accumulation rate (Pb AR) in Belgium during the Roman period. The two records were compared to assess the reliability of peat cores as archives of atmospheric Pb deposition and to established histories of atmospheric emissions from anthropogenic sources. To address these issues we analyze Pb concentration and isotopes, using ICP-MS, LA-ICP-MS and MC-ICP-MS in two peat sections, spanning 1000 yr each. Lead concentrations in the two cores range from 0.1 to 60 μg g⁻¹, with the maxima between 15 and 60 μg g⁻¹. The average natural background of Pb AR was 0.005± 0.002 mg m^-2 yr^-1 and the maximum ranges from 0.7 to 1.2 mg m^-2 yr^-1 between 50 BC and AD 215. The highest Pb AR exceed the pre-Roman period values by a factor of 25-30. Pb isotopic composition indicates that mining and metallurgical activities were the predominant sources of pollution during the Roman period. The Pb AR and chronologies in the Belgian peat cores are consistent with those reported for other continental archives as lake sediments, peat and ice cores.

Metal, primarily Fe and Zn, deficiencies affect over half of the world's population. Human diets with prevalent cereal products cause micronutrient malnutrition. Biofortification is one of the most effective approaches to alleviate malnutrition. Spring wheat genetically stable (M7) mutant lines developed with 100 and 200 Gy gamma treatments to broaden genetic variation and search for new resources were analyzed for nutritionally important minerals (Ca, Mg, K, Fe, and Zn), their bioavailability, and grain protein content (GPC). The variation was 172.3–883.0 mg/kg for Ca, 472.9–1088 mg/kg for Mg, 3128.6–5487.5 mg/kg for K, 40.9–89.0 mg/kg for Fe, and 22.2–89.6 mg/kg for Zn. In mutant lines, among the investigated minerals, the highest increases in concentrations were observed in Fe, Zn, and Ca when compared to the parent. Some mutant lines, mostly in the 100 Gy-derived germplasm, had two to three times higher Fe, Zn, and Ca concentrations, lower phytic acid concentration (1.4–2.1 times), and 6.5–7% higher GPC compare to the parent. Variation was detected for the Ca:Phy, Mg :Phy, Phy:K, Phy:Fe, and Phy:Zn molar ratios, (1.27–10.41, 5.05–18.68, 1.66–4.87, 1.40–5.32 and 1.78–11.78, respectively). The results showed how the genetic variation could be generated through radiation and be useful to develop biofortification by micronutrient varieties with their appropriate bioavailability to overcome malnutrition.

Vitamin C status is known to be associated with several demographic and lifestyle factors. These include gender, age, ethnicity, pregnancy/lactation, body weight, smoking status and dietary habits. In the present study, our aim was to interrogate the National Health and Nutrition Examination Survey (NHANES) 2017-2018 datasets to assess the impact of these factors on vitamin C dose-concentration relationships to establish if there are higher requirements for vitamin C in certain subpopulations and the possible extent of these additional requirements. The relevant data were extracted from the NHANES 2017-2018 datasets, the final cohort of which comprised 2828 non-supplementing adult males and females (aged 18 – 80+ years) with both vitamin C serum concentrations and dietary intake data available. The data was subsequently stratified by gender, age tertiles (≤36, 37-58, ≥59 years), ethnicity (non-Hispanic white, non-Hispanic black, and total Hispanic), socioeconomic tertiles (poverty income ratios: &gt;3.0, 1.36 – 3.0, ≤1.35), weight tertiles (≤72, 72-91, ≥91 kg), BMI tertiles (≤26, 26-32, ≥32 kg/m2) and smoking status. Sigmoidal (four parameter logistic) curves with asymmetrical 95% confidence intervals were fitted to the dose-concentration data. We found that males required vitamin C intakes ~1.2-fold higher than females to reach ‘adequate’ serum concentrations of 50 µmol/L. Males had both higher body weight and a higher prevalence of smoking than females. Smokers required vitamin C intakes ~2.0-fold higher than non-smokers to reach adequate vitamin C concentrations. Relative to adults in the lighter weight tertile, adults in the heaver weight tertile required ~2.0-fold higher dietary intakes of vitamin C to reach adequate serum concentrations. We did not observe any impact of ethnicity or socioeconomic status on the vitamin C dose-concentration relationship, and although no significant difference between younger and older adults was observed at vitamin C intakes &gt; 75 mg/day, at intakes &lt; 75 mg/day, older adults had an attenuated serum response to vitamin C intake. In conclusion, certain demographic and lifestyle factors, specifically gender, smoking and body weight, have a significant impact on vitamin C requirements. Overall, the data indicate that the general population must consume ~110 mg/day of vitamin C to attain adequate serum concentrations, smokers require ~165 mg/day relative to non-smokers, and heavier people (100+ kg) require ~155 mg/day to reach the same vitamin C concentrations. These findings have important implications for global vitamin C dietary recommendations.

The aim of this study was to investigate succinic acid production from lactose concentrate, a by-product of cheese-making, using Actinobacillus succinogenes and Basfia succiniciproducens. Although the capability of these strains to metabolize different sugars is already known, their application in the conversion of lactose bears high potential for optimization. With regard to B. succiniciproducens this approach is completely novel. In particular the influence of the mediums sugar concentration and its supplementation with yeast extract to prevent a lack of proteins and vitamins were examined. Lactose based media containing sugar concentrations between 20 and 65 g L-1 and 5 g L-1 yeast extract were fermented, whereby both strains showed comparable performances. The best results in succinic acid yield and acid concentration, 0.57 g g-1 initial sugar and 23 g L1, were achieved at an initial sugar concentration of 43 g L-1. The necessity of yeast extract was demonstrated using the sugar optimized medium without supplementation. As a result, yield and concentration of succinic acid dropped to 0.34 g g-1 and 13 g L-1, the sugar consumption decreased from more than 99 to less than 55 %. Therefore the supplementation amount of 5 g L-1 yeast extract can be regarded as well-balanced.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

Plants endogenous hormones play an important role in resistance to soil lead (Pb) contamination. In order to explore the response of plant hormones to Pb stress, pot experiment was conducted to analysis the hormones contents, related gene expressions and Pb accumulation of Arabis alpina under Pb treatment and transporter (CAX(cation exchangers), HMA(heavy metal ATPase) and ABC(ATP-binding cassette transporter)) activities under foliage spraying auxin (IAA). The results showed that contents of total Pb and soluble components Pb (vacuoles) in roots and leaves of Arabis alpina increased with increase of Pb treatment concentrations. Compering to 100 mg·kg-1 Pb2+ treatment, Pb contents in soluble components of roots and leaves under 300 mg·kg-1 Pb2+ treatment increased by 896.3% and 238.8%, respectively. The contents of endogenous hormones in leaves and roots increased under Pb treatment concentrations. Comparing to control (0 mg·kg-1 Pb2+ treatment), contents of auxin in roots and leaves under 100 mg∙kg-1 Pb treatment increased by 176.19% and 585.29%, respectively. Auxin contents in xylem saps under 100 and 300 mg∙kg-1 Pb treatments increased by 283.14% and 100.30%, respectively. Gene expression related to auxin transport was up-adjusted. The expressions of three gene related to auxin-repressed 12.5 kDa protein and auxin-responsive GH3 family were down-adjusted. Under foliage spraying IAA, Pb contents in leaves increased by 29.81% and Pb content in symplast sap was higher than that with non spraying IAA treatment. The activities of CAX and HMA in roots of A. alpina increased by 9.62% and 8.79% with foliage spraying IAA treatment, while activity of ABC decreased by 21.94%. In general, contents of auxin and related genes expressions of A. alpina increased under Pb treatment, which enhanced activities of CAX and HMA resulting in Pb translocation through symplast pathway.

Dendrobium okinawense is an endangered epiphytic orchid, and there has been no scientific report so far on its propagation. Protocorm is mass of cell, and protocorm-like bodies (PLBs) look alike protocorm produced by vegetative explants in vitro. Regeneration of PLBs is the most efficient technique for the orchids micro-propagation. We used different light emitting diodes (LEDs) for the efficient PLB organogenesis of D. okinawense. PLBs regenartion under green and red LED surpassed respectively 81.1% and 71.6% in numbers, and respectively 80.8% and 57.8% in fresh weight over white fluorescent light. We manipulated the culture media by different concentrations of PCIB and HMI. PLBs organogenesis promoted by low concentration, it increased respectively 35.9% and 19.3% over control by 0.01 mg/L PCIB and 0.01 ml/L HMI in numbers. Green LED and PCIB independently produced mostly similar numbers of new PLBs. Interestingly, culture media with 0.01 mg/L of PCIB further increased 8.5% of the numbers of PLBs under green LED, whereas the culture media with 0.01 mg/L HMI reduced the number of PLBs under green LED. PLBs culture under green LED with very low concentrations of PCIB manipulated culture media can significantly increase their organogenesis of D. okinawense.

In this work, nanochitosan (NC) was prepared through ionic gelation using low-molecular-weight chitosan and maleic acid (MA). The synthesized NC was charac¬terized by means of Fourier Transform Infrared Spectroscopy (FTIR), Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM). In the course of preparation, the particle size of the material was strongly depended on the parameters such as chitosan concentration and pH of the solution. By controlling the above parameters, NC with the size of smaller than 100 nm was prepared. The chitosan and prepared NC were used for the adsorption of Pb (II) from aqueous solutions in a batch system. Among the sorption parameters, pH showed the strongest effect on the sorption process and maximum Pb (II) removal was obtained at pH value of 6. The pseudo-first-order and pseudo-second-order were used to track the kinetics of adsorption process. Langmuir and Freundlich isotherms were subjected to sorption data to estimate the sorption capacity. NC proved to be an excellent adsorbent with remarkable capacity to remove Pb (II) ions from the aqueous solutions at various concentrations. The NC also showed incredible performance with a comparatively easier preparation process than other reported work.

This study presents the encapsulation of two amino acid-based ionic liquids (AAILs), 1-Ethyl-3-methylimidazolium glycine [Emim][Gly] and 1-Ethyl-3-methylimidazolium alanine [Emim][Ala], in a highly porous metal organic framework (MOF-177), to generate state-of-the-art composites for post-combustion CO2 capture. The thermogravimetric analysis (TGA) demonstrated a successful encapsulation of the AAILs, consequently dramatically reducing the composites' surface area and pore volume. Both [Emim] [Gly]@MOF-177 and [Emim][Ala]@MOF-177 had close to 3 times the CO2 uptake of MOF-177 at 20 wt.% loading, 0.2 bar, and 303 K. Additionally, 20-[Emim][Gly]@MOF-177 and 20-[Emim] [Ala]@MOF-177 enhanced their CO2/N2 selectivity from 5 (pristine MOF-177) to 13 and 11, respectively.

The PB Sudirman hydroelectric power plant, built in 1988, has fewer than 50 years of operational life. In contrast, the planned operating life for this dam is 50 years. This dam is experiencing intensive sedimentation, which results in siltation. Dredging efforts and catchment area management are conducted to extend the operational life of the dam. Therefore, technical and economic analysis of dredging activities and the potential benefits of dredged sediment is needed to determine the solution's effectiveness. We use the site survey method to conduct an environmental impact analysis and interviews with dam managers. The identification of the extent and distribution of erosion-sedimentation was carried out as part of the technical assessment. In the economic study, we calculate the dredging costs and profits from selling dredged sediments, mainly sand. The analysis results show that the dredging of deposits in the foreset slope area is not profitable. There are 17 areas of bank spoil that have economic benefits. This study concludes that the need for dredging costs on foreset slopes is higher than the profit from selling dredging sediments.

Hazardous toxic metals, such as lead and cadmium, and to a lesser extent aluminum, are extensively recognized as detrimental for health following ingestion within food and water, or following inhalation. Gut and food-derived microbes, by interacting with heavy metals, may actively or passively modulate their bioavailability inside the gut, either by adsorption or by sequestration. Such a bioremediation within the gut implies the selection of safe microbes, based on their specific capacities to immobilize metals. We investigated the metal removal ability of 225 bacteria toward the potential harmful trace elements lead, cadmium and aluminum in vitro, using Inductively Coupled Plasma Mass Spectrometry analysis. Interspecies and intraspecies comparisons were addressed and discussed among bacteria from the phylum Firmicutes, which are mostly lactic acid bacteria, including Lactobacillus spp, with some Lactococcus, Pediococcus and Carnobacterium representatives, Actinobacteria as well as Proteobacteria. The effect on mixture of lead and cadmium was also investigated. Although the purpose of such a screening is so far not to elucidate each of the various strain specific- and metal dependent- mechanisms of heavy metal removal, we identified potential bacteria which are able to alleviate Pb(II) and Cd(II) concerns in order to propose performing candidate probiotics for metal xenobiotic bioremediation.

The Dongtangzi large Zn-Pb deposit is located in the southwest of the Fengxian-Taibai (abbr. Fengtai) ore cluster in the west Qinling orogen, whose origin has been controversial, positing diverse genesis mechanisms such as sedimentary-exhalative (SEDEX), sedimentary-reformed, and epigenetic hydrothermal type. In this work, based on detailed observation and systematic study on ore geology, the results of high-precision Rb-Sr isotopic dating on sulfides of the main orebody and Sm–Nd isotopic dating on associated carbonates have been carried out, which yield isochron ages of 211.6 ± 2.6 Ma and 211 ± 4 Ma, respectively. In-situ S-Pb isotopic studies show that the ore related sulfides display a narrow range of δ³⁴S values from 1.1 ‰ to 10.2 ‰, with ²⁰⁶Pb/²⁰⁴Pb, ²⁰⁷Pb/²⁰⁴Pb and ²⁰⁸Pb/²⁰⁴Pb ratios of 18.07 to 18.27, 15.64 to 15.66, and 38.22 to 38.76, respectively. While the pyrite of sedimentary period and the granite porphyry dike have δ³⁴S values vary from 15.8 to 21.4‰, and from 2.1 to 4.3‰ (with ²⁰⁶Pb/²⁰⁴Pb ratios of 18.09 to 18.10, ²⁰⁷Pb/²⁰⁴Pb ratios of 15.59 to 15.61, and ²⁰⁸Pb/²⁰⁴Pb ratios of 38.17 to 38.24) respectively. Combining the regional geology, we propose that the Dongtangzi Zn-Pb deposit is the product of multi-stage epigenetic hydrothermal fluid processes, driven by late Triassic regional tectono-magmatic activities in regional extensional regime, with metallic materials originate from a mixture of Triassic magmatic processes and metamorphic basement.

The photocatalysis process over N-doped TiO2 under visible light is examined for Pb(II) oxidation to form the less toxic and handleable PbO2 suggesting a new method for Pb(II) remediation. The doping TiO2 with N element was conducted by simple hydrothermal technique and using urea as the N source with various concentrations. The doped photocatalysts were characterized by DRUVS, XRD, FTIR and SEM-EDX instruments. Photocatalysis of Pb(II) through batch experiment was performed for evaluation of the doped TiO2 activity under visible light, with applying various fractions of N doped, photocatalyst weigh, irradiation time, and solution pH. The research results attributed that N doping has been successfully performed, that shifted TiO2 absorption into visible region, allowing it to be active under visible irradiation. The photocatalytic removal of Pb(II) under visible ligth over N-TiO2 showed more effective than that of over the un-doped photocatalyst. The removal of Pb(II) has notably taken place through oxidation, that may form PbO2. The highest photocatalytic oxidation of Pb(II) 15 mg/L in 25 mL of the solution could be reached by using TiO2 doped with 10%w of N, 15 mg of N-TiO2 weight, 30 minutes of time, and at pH 8, suggesting a feseable method for Pb(II) remediation.

Pb found in rain water is not only caused by tin roof on houses but also caused by the pollution of industrial activities, vehicles and land clearing activity by fire. Pb pollutant dissolves and enters into rain water storages and it’s consumed as drinking. Pb can cause bad impact to human, for example disruption of enzyme, anemia and low intelligence. The purposes of this research are (1) to evaluate Pb, pH and turbidity level in rain water, (2) to analyze the effectiveness of mollusk sand filtration and the absorption of activity carbon to decrease Pb, turbidity and pH, and (3) to analyze the correlation of Pb, length of stay and smoking habit on public health. This research is an experimental by using pre and post test designs with control and observational by using cross sectional design. The research was conducted in urban and rural areas of Pontianak and Kubu Raya regency. The sampling was done in determining the number of samples of Pb, pH and turbidity in rain water. The analyzing the data by using computer program. The results show that: (1) the average of Pb, pH and turbidity level before treatment is considered high at 131.7 µg/L on Pb, turbidity at 20 NTU and low pH at 5.2. After the treatment was the Pb has decreased to 0.71 µg/L and turbidity has to 5.66 NTU, pH to 6.9 and (2) Rain water treatment is very effective to decrease Pb for 99.4% and turbidity for 72%, and (3) there is a correlation among Pb found in rain water, length of stay and smoking activity to public health. Recommends that: the residents of Pontianak and Kubu Raya to process rain water before consuming. The rain water treatment can be done by applying mollusk sand filtration and absorption of active carbon.

Diamidophosphate has been identified as a possible prebiotic compound used in the precursor membranes of the first ‘life’. Compounds such as these will be helpful in developing novel biomimetic approaches in synthetic chemistry. Thermochemical data for this type of compounds are not available. Hess’ law and estimates from calorimetric measurements used by Wakefield in the 1970s for other amido phosphates have been used to estimate the thermochemical values for the diamido and monoamido-phosphoric acid. Enthalpy of formation at 298.15 ^oC is calculated as – 821.9 kJ/mol and the free energy of formation calculated as -813.5 kJ/mol for the diamidophosphoric acid. The calculated enthalpy of formation of monoamidic phosphoric acid is -1117.1 kJ/mol and its free energy of formation is - -1105 kJ/mol.

The determination of the specific surface free energy, specific properties and Lewis’s acid base of solid materials is of capital importance in many industrial processes such as adhesion, coatings, two dimensional films and adsorption phenomena. (1) Background: The physicochemical properties of many solid particles were characterized during the last forty years by using the retention time of injected well-known molecules into chromatographic column containing the solid substrates to be characterized. The obtained net retention time of the solvents adsorbed on the solid allowing the determination of the net retention volume directly correlated to the specific surface variables, dispersive, polar and acid-base properties. (2) Methods: Many chromatographic methods were used to quantify the values of the different specific surface variables of the solids. However, one found a large deviation between the different results. In this paper, one proposed a new method that quantify the specific free energy of adsorption as well as the Lewis’s acid-base constants of many solid surfaces. (3) Results: The new applied method allowed us to obtain the specific enthalpy and entropy of adsorption of polar model organic molecules on several solid substrates such as silica, alumina, MgO, ZnO, Zn, TiO2 and carbon fibers. (4) Conclusions: our new method based on the separation between the dispersive and polar free surface energy allowed to better characterize the solid materials.

Soil washing is a rapid and efficient method for heavy metals removal. In this study, in order to prove the feasibility of leaching remediation technology for remediation of lead-contaminated soil around a smelter, intermittent oscillating washing tests and extensive continuous tests were conducted to remediate Pb contaminated soils. Plant growth tests with wheat (Bainong Aikang 58) were also conducted to investigate the effects of leaching on plant growth and the Pb content of stems and leaves. The results revealed that in soils, Pb mainly exists in the forms of PbCO3, Pb5(PO4)3Cl2, PbSO4, and in small amounts of PbS. The intermittent oscillating washing tests showed that a lower liquidsolid(L/S) ratio and a higher leaching temperature and time were related to increased Pb removal efficiency. The Pb removal efficiency rates in the oscillating washing tests and the extensive continuous tests were 72.50% and 69.94%, respectively. In addition, the chemical and physical characteristics of the soil were basically unchanged after the leaching regimes. The results of the plant growth tests showed that the leaching regimes did not have a negative effect on the survival rate and growth of the wheat, and the heavy metal contents of the stem and leaf were effectively reduced. This study provides a reference for the large-scale remediation of contaminated soils.

A powder synthesis of PbMoO₄ from ancient lead (Pb) and deeply purified commercial MoO₃ powders was performed using a wet chemistry technique to achieve the low radioactivity scintillator for neutrinoless double beta decay search in ¹⁰⁰Mo. The synthesized powders were used to grow single crystals of PbMoO₄ by a Czochralski technique in Ar environment. The luminescence and scintillation properties were measured with excitations using UV, X- and γ-rays in temperature range of 10-300 K. Annealing of the grown PMO crystal in air atmosphere enhanced the scintillation light yield by ~3 orders of magnitude compared to that measured before annealing. The scintillation light yield of grown PMO crystal at 10 K is found to be 127% to that of a reference PMO crystal under 662 keV γ-rays excitation from a ¹³⁷Cs source. The background measurement of the grown crystal performed at 50 K shows negligible activity from ²¹⁰Pb compared to that of reference PMO crystal. These preliminary performances show that the PMO crystal grown from ancient Pb and deeply purified MoO₃ powders has the great potential to be used as cryogenic scintillator for the neutrinoless double beta decay search in ¹⁰⁰Mo.

The Kuznetsk Basin (Kuzbass) is one of the largest coal basins in Siberia and a reference area for the ancient Angaraland continent. The proximity of the Kuzbass and Siberian platform caused their biotic similarities in the Late Palaeozoic. However, due to biota endemism, the Kuzbass Upper Palaeozoic does not correlate directly with the International Chronostratigraphic Chart (ICC). This paper discusses radioisotopic (CA-ID-TIMS) dating of zircons from a volcanic tuff located in the Starokuznetsk Formation. This level matches the interval of the Balakhonka/Kolchugino (B/K) floral change in Kuzbass, i.e. the gradual replacement of cordaitoid-dominated wet forests (Balakhonka flora) by more arid fern-pteridosperm-cordaitoid assemblages (Kolchugino flora). New age (276.9 ± 0.4 Ma) directly correlates the Starokuznetsk Fm with the Upper Kungurian of the ICS. We compared the Kuzbass data with data of the Western Verkhoyanie, where Middle Permian ammonoids (Sverdrupites assemblage) occur in strata recording the B/K floral change. Available (ICC) and new datings indicate the lag between the B/K floral change in low (Kuzbass) and high (Verkhoyanie) latitudes of Angaraland. The B/K floral change in the Kuzbass began in the early Late Kungurian and was completed by the end of this age. In contrast, the B/K floral change in Verkhoyanie began at the end of the Late Kungurian and was completed in the Late Wordian. The delay in the floral changes at different latitudes of Angaraland suggests that existing interregional correlations need further improvement.

Detailed mapping and structural observations on the Cycladic Blueschist Unit (CBU) of Iraklia island integrated by detrital zircon (DZ) U-Pb ages elucidate the Mesozoic pre-subduction evolution and the Cenozoic orogenic events. Field data reveal that the Iraklia tectonostratigraphy includes a heterogeneous Lower Schist Unit juxtaposed against a Variegated Marble Unit and an overlying Upper Schist Unit. The contact is an extensional ductile-to-brittle-ductile, top-to-N shear zone, associated with the Oligo-Miocene exhumation. The DZ spectrum of the Lower Schist Unit characterized by Gondwanan/peri-Gondwanan provenance signatures points to Late Triassic maximum depositional ages (MDAs). A quartz-rich schist layer yielded Precambrian DZ ages exclusively, considered part of the pre-Variscan metasedimentary Cycladic Basement, equivalent to those observed on Ios island. A significant change occurred during the deposition of the Upper Schist Unit, revealing Late Cretaceous MDAs and a high amount of Late Paleozoic DZ ages, attesting to more internal Pelagonian source areas. The imprint of Paleotethyan vs. Neotethyan geodynamic events is revealed in the DZ U-Pb ages record. The Triassic DZ input demonstrates eroded volcanic material related to the final Paleotethys closure and the Pindos/CBU rift basin opening. Late Cretaceous metamorphic/magmatic zircons and ~48-56 Ma zircon rims constrain the onset of subduction and high-pressure metamorphism.

Researchers from around the world are looking for better and cheaper ozone production. One of the methods increasing the efficiency of ozone production is the use to a rotating electrode presented in this paper. Experiments were carried out which shows that the most important parameters are the materials used on the electrodes and the condition of its surface. The metallographic investigations of the electrodes after continuous monthly work was made, which show how the raids layers are formed. As a result of working in a highly oxidizing environment, the electrode is oxidized in the process of chemical corrosion. It is obvious that the layer of corrosion products created during the work of the plasma reactor isolates the surface of the electrode, which reduces the intensity of the electric field, causing a decrease in the amount of plasma generated, which is a direct cause of lowering the concentration of ozone during this process. The dynamics of plasma generation process and the type of electrode material working in changing process conditions are the decisive factors influencing the concentration of ozone produced. The influence of the medium, which is the electrode material, depends mainly on its resistance to corrosion in the environment of dynamically changing conditions, e.g. electrode rotation, oxygen flow through the rotating electric field and the long monthly working time of the plasma reactor.

Flushing tap water is often promoted as a simple and low cost approach to reducing water lead exposures. This study evaluated lead reduction when prevailing flush guidelines (30 seconds-2 minutes) are implemented in a city compliant with lead-associated water regulations (New Orleans, LA). Water samples (n=1,497) collected from a convenience sample of 376 residential sites (2015-2017) were analyzed for lead in samples collected: at 1) first draw (n=375), and after incremental flushes of 2) 30-45 seconds (n=375), 3) 2.5-3 minutes (n=373), and 4) 5.5-6 minutes (n=218). There was no significant reduction when compared to the first draw lead level, until the 6 minute flush (p<0.05); but most sites (52%) still had detectable lead (≥1 ppb) after 6 minutes. Older homes (pre-1950) and low occupancy sites had significantly higher WLLs (p<0.05).Each sample type had health-based standard exceedances at over 50% of sites sampled (max: 58 ppb). While flushing is an effective short-term approach to remediate high lead, prevailing flush recommendations are an inconsistently effective exposure prevention measure that can often inadvertently increase exposures. Public health messages should be modified to ensure appropriate application of flushing for specific cities, while acknowledging its short-comings and practical limitations.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

Gold occurrence Maljavr, located in amphibolite metamorphosed rocks in the Uragubsky greenstone belt, is the first gold prospect connected with conglomerates of Archean age, found in the Fennoscandian Shield. Gold mineralization is controlled by a series of lenses of altered rocks in biotite gneiss-metaconglomerate. The age of zircon from biotite gneiss in the zone of alteration is 2665±22 Ma, this is considered as the time of alteration processes. Biotite gneiss and altered rocks were later intruded by tourmaline granite pegmatite at 2508±7Ga, the pegmatite caused recrystallization of sulfide minerals in the altered rocks. Visible gold in association with bismuth minerals native bismuth, ehrigite (the second finding in the world), maldonite, bismuthinite, joseite-B, hedleyite was found exceptionally in polymineral inclusions in recrystallized arsenopyrite and löllingite. The age of pegmatite 2508±7Ma we regard as the time of formation of gold-bismuth mineralization. Geological position of the Maljavr occurrence, the linkage of gold mineralization with pegmatite, geochemical association Au-As-Se-Te-Bi in the mineralized rocks – all these characteristics correspond to intrusion-related gold deposits. Biotite gneiss-metaconglomerate, hosting the mineralized altered rocks, was the probable primary source of arsenic and gold for mineralization.

The heavy metal lead (Pb) can irreversibly damage the human nervous system. To help understand Pb-induced damage, we applied a genetically encoded Förster resonance energy transfer (FRET)-based Pb biosensor Met-lead 1.44 M1 to two living systems to monitor the concentration of Pb: induced pluripotent stem cell (iPSC)-derived cardiomyocytes as a semi-tissue platform, and Drosophila melanogaster fruit flies as an in vivo animal model. Different FRET imaging modalities were used to obtain FRET signals, which represented the presence of Pb in the tested samples in different spatial dimensions. Using iPSC-derived cardiomyocytes, the relationship between beating activity (20–24 beats per minute, bpm) determined from the fluctuation of fluorescent signals and the concentrations of Pb represented by the FRET emission ratio values of Met-lead 1.44 M1 was revealed from simultaneous measurements. Pb (50 μM) affected the beating activity of cardiomyocytes, whereas two drugs that stop the entry of Pb differentially affected this beating activity: verapamil (2 μM) did not reverse the cessation of beating, whereas 2-APB (50 μM) partially restored this activity (16 bpm). The results clearly demonstrate a potential of this biosensor system as an anti-Pb drug screening application. In the Drosophila model, Pb was detected within the adult brain or larval central nervous system (Cha-gal4>UAS-Met-lead 1.44 M1) using fast epifluorescence and high-resolution two-photon 3D FRET ratio image systems. The tissue-specific expression of Pb biosensors provides an excellent opportunity to explore the possible Pb-specific populations within living organisms. We believe that this integrated Pb biosensor system can be applied to the prevention of Pb poisoning and advanced research on Pb neurotoxicology.

Novel collector lead(II)-benzohydroxamic acid (Pb(II)-BHA) complexes in aqueous solution were characterized by using experimental approaches, including Ultraviolet-visible (UV-Vis) spectroscopy and electrospray ionization–mass spectrometry (ESI-MS), as well as first-principle density functional theory (DFT) calculations with consideration for solvation effects. The Job plot delineated that a single coordinated Pb(BHA)⁺ should be formed first, and the higher coordination number complexes can be formed subsequently. Moreover, the Pb(II)-BHA species can aggregate with each other to form complicated structures, such as Pb(BHA)₂ or highly complicated complexes. ESI-MS results validated the existence of Pb-(BHA)_n=1,2 under different solution pH values. Further, the first-principles calculations suggested that Pb(BHA)⁺ should be the most stable structure, and the Pb atom in Pb(BHA)⁺ will act as an active site to attack nucleophiles. These findings are meaningful to further illustrate the adsorption mechanism of Pb(II)-BHA complexes in mineral processing.

Precise binding affinity predictions are essential for structure-based drug discovery (SBDD). Focal adhesion kinase (FAK) is a member of the tyrosine kinase protein family and is overexpressed in a variety of human malignancies. Inhibition of FAK using small molecules is a promising therapeutic option for several types of cancer. Here, we conducted computational modeling of FAK targeting inhibitors using 3-dimensional structure-activity relationship (3D-QSAR), molecular dynamics (MD), and hybrid topology-based free energy perturbation (FEP) methods. The structure-activity relationship (SAR) studies between the physicochemical descriptors and inhibitory activities of the chemical compounds were performed with reasonable statistical accuracy using CoMFA and CoMSIA. These are two well-known 3D-QSAR methods based on the principle of supervised machine learning (ML). Essential information regarding residue-specific binding interactions was determined using the MD and MM-PB/GBSA methods. Finally, physics-based relative binding free energy (〖∆∆G〗_RBFE^(A→B)) values of analogous ligands were estimated using the alchemical FEP simulation. An acceptable agreement was observed between the experimental and computed relative binding free energies. The overall results using ML and physics-based hybrid approaches could be useful for the rational optimization of accessible lead compounds with similar scaffolds targeting the FAK receptor.

Obesity results in hepatic fat accumulation, i.e., steatosis. Besides the fat overload, impaired fatty acid β-oxidation also promotes steatosis. Fatty acid β-oxidation takes place in mitochondria and peroxisomes. Usually very long chain and branched-chain fatty acids are first oxidized in peroxisomes, and the resultant short chain fatty acids are further oxidized in mitochondria. Peroxisome biogenesis is regulated by peroxin 16 (PEX16). In liver-specific PEX16 knockout (Pex16Alb-Cre) mice, hepatocyte peroxisomes were absent, but hepatocytes proliferated, and liver mass was enlarged. These results suggest that normal liver peroxisomes restrain hepatocyte proliferation and liver sizes. After high fat diet (HFD) feeding, body weights were increased in PEX16 floxed (Pex16fl/fl) mice and adipose-specific PEX16 knockout (Pex16AdipoQ-Cre) mice but not in the Pex16Alb-Cre mice, suggesting that the development of obesity is regulated by liver PEX16 but not by adipose PEX16. However, it was previously reported that HFD-induced obesity in the Pex16AdipoQ-Cre mice was more severe than in the wild type mice, which was not observed until 27 weeks of HFD feeding. Thus, liver initiates the development of obesity, which is enhanced by abnormal adipocytes. HFD increased liver mass in the Pex16fl/fl mice but somehow reduced the already enlarged liver mass in the Pex16Alb-Cre mice. Basal levels of serum triglyceride, free fatty acids and cholesterol were decreased whereas serum bile acids were increased in the Pex16Alb-Cre mice, and HFD-induced steatosis was not observed in the Pex16Alb-Cre mice. These results suggest that normal liver peroxisomes contribute to the development of liver steatosis and obesity.

The solute carrier family 25 (SLC25) participates in the transport of metabolites and cofactors across the membranes of mitochondria, plastids, peroxisomes, and endoplasmic reticulum. By calling for genomic blocks involved in adjacent metabolic reactions, this report introduces gene clusters of the Slc25 subfamily 44, stilbene and chalcone synthases, and subunits of the mitochondrial electron transfer complexes. The Slc25A44 gene was found ubiquitously expressed and transcriptionally co-regulated with energy metabolism genes in human, mouse, and Arabidopsis thaliana. The Slc25A44s also had no homozygous missense mutation and were highly conserved at intra-species level with the majority of polymorphism present in the non-coding regions. When expressed in oocytes, AdSlc25A44 from Arachis duranensis showed transport activity for the common precursors of flavonoids, stilbenoids, and ubiquinone. Accordingly, AdSLC25A44 and its human orthologue HsSLC25A44 elevated the production of para-coumaric, 4-aminobenzoic, and 4-hydroxybenzoic acids in Saccharomyces cerevisiae strains designed to produce para-coumaric acid via different pathways. Moreover, the engineered SLC25 subfamily specific signature, i.e., AdSLC25A44^LWW206IQF, had a stronger effect on para-coumaric acid secretion than the native variant. Importantly, the aerobic growth-rate of S. cerevisiae was significantly higher when expressing the AdSLC25A44, HsSLC25A44, or AdSLC25A44^LWW206IQF. These results suggest that SLC25A44 is an essential mitochondrion-ER-nucleus zone transporter associated with metabolism of secondary metabolites and energy.

Soarinho Alkaline Intrusion, southeastern Brazil, makes part of the Serra do Mar Igneous Province, and it is composed of alkali feldspar syenite, alkali feldspar trachyte, quartz syenite, and mon-zonite. Geochemical and geochronological analysis of the Soarinho were compared with data from its neighbors Rio Bonito and Tanguá. Zircon U-Pb Laser Ablation ages show that Soarinho is youngest than Rio Bonito and Tanguá. Ages obtained from the monzonite (60 ± 2 Ma), alkali feldspar syenite (58 ± 2 Ma), and quartz syenite (58 ± 2 Ma) are indistinguishable within error. Petrographic and geochemical data show a clear contrast among Soarinho, Rio Bonito, Tanguá, and Lu-Hf isotopic data for the three alkaline intrusions (all negative), point to some similarities in their sources. The data suggest an enriched mantle source for Soarinho; however, an older con-tinental crust contribution cannot be discarded.

Among the thermophysical properties, the surface / interfacial tension, viscosity and density / molar volume of liquid alloys are the key properties for the modelling of microstructural evolution during solidification. Therefore, only reliable input data can yield accurate predictions preventing the error propagation in numerical simulations of solidification related processes. Due to experimental difficulties related to reactivity of metallic melts at high temperatures, the measured data are often unreliable or even lacking. The application of containerless processing techniques either leads to a significant improvement of the accuracy or makes the measurement possible at all. On the other side, accurate model predicted property values could be used to compensate the missing data; otherwise, the experimental data are useful for the validation of theoretical models. The choice of models is particularly important for the surface, transport and structural properties of liquid alloys representing the two limiting cases of mixing, i.e. ordered and phase separating alloy systems. To this aim, the thermophysical properties of the Fe-Si and Cu-Pb systems were analysed and the connections with the peculiarities of their mixing behaviours are highlighted.

The human chromosome 11q13 (HSA 11q13) genomic locus is a major cancer hotspot and has been established as the most frequently altered by amplification in a variety of human cancers. The fatty acid desaturase genes (FADS1, FADS2 and FADS3) localize to the 11q12- 13.1 region. FADS2 activity is promiscuous, catalyzing biosynthesis of polyunsaturated and monounsaturated fatty acids, including unsaturated branched chain fatty acids (BCFA) by Δ6, Δ8, and Δ4 desaturation toward at least 16 substrates. Our main aim here is to review known and putative consequences of FADS2 dysregulation due to effects on the 11q13 locus in various cancer types. We searched PubMed and Google Scholar databases for articles that showed 11q13 amplification and studies reporting FADS2 function in various cancer types. FADS2 silencing causes synthesis of sciadonic acid (ScA, 5Z,11Z,14Z-20:3) in MCF7 cells and breast cancer in vivo. 5Z,11Z,14Z-20:3 is structurally identical to the eicosanoid precursor arachidonic acid (5Z,8Z,11Z,14Z–20:4) except it lacks the internal Δ8 double bond required for prostaglandin and leukotriene synthesis, among other eicosanoids. Melanoma, prostate, liver and lung cancer cells insensitive to SCD inhibition show increased FADS2 activity leading to sapienic acid (16:1n10) biosynthesis from 16:0. Elevated serum mead acid (20:3n-9) levels were found in more than a third of hepatocellular carcinoma patients, indicative of an unsatisfied demand for arachidonic acid, likely as a substrate for eicosanoids. A highly expressed circular RNA (hsa_circ_022382) within an exonic region of FADS2 is associated with shorter overall survival in colorectal cancer patients. Similarly, in lung cancer tissues circFADS2 RNA is highly expressed. Palmitic acid (16:0) is a common substrate for SCD and FADS2. FADS2 circular RNAs are at high levels in colorectal and lung cancer tissues. The evidence thusfar supports an effort for future research on the role of FADS2 as a tumor suppressor in a range of neoplastic disorders.

Choline is metabolized by the gut microbiota into trimethylamine (TMA), the precursor of pro-atherosclerotic molecule trimethylamine N-oxide (TMAO). Reduction of TMA formation has been shown to provide to cardioprotective effects, and some phytochemicals may produce such reduction. This study aimed to develop an optimized, high-throughput anaerobic fermentation methodology to study inhibition of choline microbial metabolism into TMA by phenolic compounds with healthy human fecal starter. Optimal fermentation conditions were: 20 % fecal slurry (1:10 in PBS), 100 M choline, and 12 h fermentation. Also, 10 mM of 3,3-dimethyl-1-butanol (DMB) was defined as a positive TMA production inhibitor, achieving a ~50 % reduction in TMA production. Gallic acid and chlorogenic acid reported higher TMA inhibitory potential (maximum of 80 -90 % in. TMA production inhibition), with IC50 around 5 mM. Nor DMB neither gallic acid and chlorogenic acid reduced TMA production through cytotoxic effects, indicating mechanisms such as altered TMA lyase activity or expression.

This paper is devoted to an accurate determination of the London dispersive and polar free energy of adsorption, the two Lewis acid γs+ and base γs- components of polar surface energy γsAB of 2D single-crystalline and polycrystalline covalent organic frameworks such as TAPPy-TPA-COFs. Inverse gas chromatography (IGC) at infinite dilution was used to quantify the different surface parameters of the different materials. From IGC measurements, one determined the net retention time of the adsorption of n-alkanes and several polar solvents on single-crystalline and polycrystalline covalent organic frameworks. The free surface Gibbs energy of adsorption was obtained for the various organic molecules at different temperatures from their net retention volume values. The separation between the London dispersive energy and the polar energy of adsorbed molecules was carried out by using a new thermodynamic parameter PSX chosen as new indicator variable and taken into account the deformation polarizability and the harmonic mean of the ionization energies of solvents and solid materials, derived from London dispersion equation. The obtained results are very promising for the accurate determination of the surface thermodynamic parameters of adsorption of organic solvents on solid surfaces.

The results of an LA-ICP-MS U-Pb dating and Hf isotope study of zircon crystals separated from small eclogite xenoliths found in Devonian kimberlites within the Prypyat horst, Ukraine, are reported. The studied area is located in the Central Belarusian Suture Zone, which represents a Paleoproterozoic belt extending along the boundary between the Sarmatian and Fennoscandian segments of the East European Platform. Four laser ablation sites on two zircon grains yielded Paleoproterozoic U-Pb ages between 1954 ± 24 Ma and 1735 ± 54 Ma. In contrast, three of four Hf sites revealed negative εHf values and Paleoarchean to Mesoarchean model ages, excluding the possibility that the eclogite xenoliths represent segments of a Paleoproterozoic subducted slab or younger mafic melts crystallized in the subcontinental lithospheric mantle. A single laser ablation Hf spot yielded a positive εHf value (+3) and a Paleoproterozoic model age. Two models for eclogite origin can be proposed. The first foresees the extension of the Archean lower-crustal or lithospheric roots beneath the Central Belarus Suture Zone for over 200 km from the nearest known outcrop of Archean rocks. The second model is that the Central Belarus Suture Zone represents a rifted-out fragment of the Kola-Karelian craton that was accreted to Sarmatia before the actual collision of these two segments of Baltica.

This research illustrates modification of multi-walled carbon nanotubes (MWCNT) by ZrO2/Pb to construct nanocomposites (MWCNT/ZrO2/Pb-NCs) by simple precipitation technique and subsequently examine its ability for adsorption of Amido black (AB) and Eosin B (EB) dyes in binary system. The present nanocomposites investigation by FESEM, XRD, FTIR, and EDX analysis, reveal its as-synthesized crystalline nature with cubic morphology and average particle size 30–50 nm. The present nano-adsorbent represent high efficiency for AB and EB adsorption from aqueous solution, while dependency of variables including pH, initial concentration of dyes, contact time and MWCNT/ZrO2/Pb-NCs mass were analyzed by central composite design (CCD). The predicted maximum removal percentage was 95% removal for both dyes is consequence of adjustment of operational conditions at pH of 6.0; 0.05 g MWCNT/ZrO2/Pb-NCs; 15 min stirring at 15 mg L-1 for both dyes. The Langmuir as applicable for representation and description of reveal data of adsorption with adsorption capacity of 15.46 and 16.92 mg g-1 for AB and EB, respectively. Pseudo-first order model owing to its high correlation coefficient and closeness of experimental and theoretical data well represented behavior of corresponding adsorption system. Mechanism examination strongly proof high contribution of external mass transference as the main rate-controlling step. The successful regeneration of MWCNT/ZrO2/Pb-NCs suggested their usefulness in wastewater treatment and its ability of environmental management.

Fosmidomycin (FOS) is a naturally occurring compound active against the enzyme DXR in the MEP pathway, and using it as a template for lead structure design is an effective strategy in developing new active compounds. In this work, by replacing the hydroxamate unit of FOS with pyrazole, isoxazole and the related heterocycles that also have the metal ion binding affinity, while retaining the monophosphonic acid in FOS or replacing it with a bisphosphonic acid group, heterocycle-containing mono- and bisphosphonic acid compounds as FOS analogs were designed. The key steps involved in the facile synthesis of these FOS analogs include the Michael addition of diethyl vinylphosphonate or tetraethyl vinylidenebisphosphonate to β-dicarbonyl compounds and the subsequent cyclic condensation with hydrazine or hydroxylamine. Two additional isoxazolinone-bearing FOS analogs were synthesized by the Michaelis-Becker reaction with diethyl phosphite as a key step. The bioactivity evaluation on model plants demonstrated that several compounds have better herbicidal activities compared to FOS, with the most active compound showing a 3.7-fold inhibitory activity on Arabidopsis thaliana, while on the root and stalk of Brassica napus L. and Echinochloa crus-galli in pre-emergence inhibitory activity test, the activities of this compound were found to be 3.2- and 14.3-, 5.4- and 9.4-fold, respectively, and in post-emergency activity test on Amaranthus retroflexus and Echinochloa crus-galli, 2.2- and 2.0-fold inhibition activities were displayed. Despite the significant herbicidal activity, this compound exhibited a DXR inhibitory activity lower than that of FOS but comparable to that of other non-hydroxamate DXR inhibitors, and the dimethylallyl pyrophosphate rescue assay gave no statistical significance, suggesting a different target might be involved in the inhibiting process. This work demonstrates that using bioisosteric replacement can be considered a valuable strategy for discovering new FOS analogs that may have high herbicidal activity.

This work reports of the use of a bench scale chemostat (CSTR) in continuous mode and of a pilot scale membrane bioreactor (MBR) in fed-batch mode to intensively produce acetic and butyric acids using Cl. butyricum grown on synthetic media. These studies were then used to perform a cost estimation study of the MBR system to assess the potential economic impact of this proposed methodology. The MBR system was found highly productive reaching 37.88 g L-1 h-1 of acetic and 14.44 g L-1 h-1 of volumetric cell productivity, favoring acetic acid production to butyric at a ratio 3:1. The cost of preparation and production of carboxylic acids using this system was found as 0.0062 £PS/kg respectively and an up to 99% carbon recovery.

As the largest accretionary orogen in the world, the Central Asian Orogenic Belt (CAOB) has continuous juvenile crustal growth in the Phanerozoic. The northern margin of the North China Craton(NCC) and its adjacent area is the eastern segment of the CAOB, and is a key area to study the geological evolution of Paleo-Asian Ocean (PAO). In the Permian, the west of the northern margin of NCC belongs to a post-collision extensional environment, and the east belongs to a subduction stage. But, As a connecting area, the Permian evolution of PAO in the middle of northern margin of NCC has not been systematically studied. In order to fill the blank and understand the temporal and spatial continuous evolution process of PAO, this paper focused on the Permian granitic rocks in the Chifeng area, zircon U-Pb dating and the geochemical analysis of the whole rock main and trace elements were conducted in order to build a granite chronological framework, discuss the genesis and tectonic background of the granite rocks as well as the magma-tectonic evolution history in the Chifeng area. Zircon U-Pb dating results of 8 samples are 269±1 Ma, 268±3 Ma, 260±4 Ma, 260±1 Ma, 260±1 Ma, 255±2 Ma, 254±2 Ma, 256±1Ma, which showed that the Permian granitic rocks had undergone three stages of emplacement: (1) The monzogranite and syenite (294-284 Ma); (2) The monzogranite (269-260Ma) and (3) The monzogranite and syenite (256-254Ma). The Middle Permian magmatism (269-260Ma) was represented by the monzogranite assemblages with different grain sizes. The geochemical characteristics showed that they were high-potassium calc-alkaline-potassium dossonite series of granites formed in compressional environment, indicating there was a collision between the Xing’an-Mongolian Orogenic Belt (XMOB) and the North China Craton (NCC). During the Late Permian-Early Triassic (256-248Ma), the granites in the Chifeng area are dominated by the A-type and I-type granites of high-potassium calc-alkaline series formed under an extensional environments, which constituted typical "bimodal" rock assemblage combined with the coeval basic rocks, suggesting the study area was in an extensional environment where the subducting slab is fragmented during the collision between the XMOB and the NCC. According to emplacement time and occurrence location, the plutons are interpreted to have been generated by the subduction-collision of the Paleo-Asian oceanic crust beneath the NCC. This study provides strong evidence for Permian tectonic evolution and the characterization of the eventual closure of the Paleo-Asian Ocean in the Chifeng City at the northern margin of the NCC.

Most methods for measuring environmental lead (Pb) content are time consuming, expensive, hazardous, and restricted to specific analytical systems. To provide a facile, safe tool to detect Pb, we created pMet-lead, a portable fluorescence resonance energy transfer (FRET)-based Pb biosensor. pMet-lead comprises a 3D-printed frame housing a 405-nm laser diode — an excitation source for fluorescence emission images (YFP and CFP) — accompanied by optical filters, a customized sample holder with a Met-lead 1.44 M1 (the most recent version)-embedded biochip, and an optical lens aligned for smartphone compatibility. Measuring the emission ratios (Y/C) of the FRET component enables Pb detection with a dynamic range of nearly 2 (1.96), pMet-lead/Pb dissociation constant (K_d) 45.62 nM, and limit of detection 40 nM (0.832 μg/dL, 8.32 ppb). To mitigate earlier problems with lack of selectivity for Pb vs. zinc, we preincubated samples with tricine, a low-affinity zinc chelator. We validated pMet-lead measurements of characterized laboratory samples and unknown samples from six regions in Taiwan by inductively coupled plasma mass spectrometry (ICP-MS). Notably, two unknowns had Y/C ratios significantly higher than that of the control (3.48 ± 0.08 and 3.74 ± 0.12 vs. 2.79 ± 0.02), along with Pb concentrations (10.6 ppb and 15.24 ppb) above the WHO-permitted level of 10 ppb in tap water, while the rest four unknowns showing no detectable Pb upon ICP-MS. These results demonstrate that pMet-lead provides a rapid, sensitive means for on-site Pb detection in water from the environment and in living/drinking supply systems to prevent potential Pb poisoning.

The early Paleozoic is a crucial period in the formation and evolution of the Eastern Kunlun Orogenic Belt (EKOB), and is of great significance for understanding the evolutionary history of the Proto-Tethyan Ocean. This paper presents new petrography, geochemistry, zircon U–Pb dating, and Lu–Hf isotopic research on the Yuejingshan gabbro from the eastern segment of the EKOB. Zircon U–Pb data suggests that the gabbro formed in the Early Silurian (435 ± 2 Ma). All samples have relatively low TiO₂ contents (0.45–2.97%), widely varying MgO (6.58–8.41%) and Mg^# (58–65) contents, and are rich in large ion lithophile elements (LILE such as Rb, Ba, Th, and U) and light rare earth elements (LREE). This indicates that it has a similar geochemical composition to island arc basalt. The major element features indicate that the formation of this gabbro underwent fractional crystallization of clinopyroxene, olivine, and plagioclase. The depletion of high field strength elements (HFSE, such as Nb, Ta, and Ti), and a slightly positive Hf isotope (with εHf_(t) ranging from 1.13 to 2.45) may be related to the partial melting of spinel-bearing peridotite, led by slab fluid metasomatism. The gabbro likely represents magmatic records of the latest period of the early Paleozoic oceanic crust subduction in the Eastern Kunlun. Therefore, the final closure of the Proto-Tethyan Ocean and the beginning of collisional orogeny occurred before the Early Silurian.

A series of precise data consisting of zircon U–Pb ages, whole-rock geochemistry and Sr–Nd–Hf isotope compositions from the Huhetaoergai granitic pluton was collected in this study and combined with data from the western Huhetaoergai, Zhuxiaogubuhe and Yagan granitic plutons to constrain the petrogenesis and tectonic setting of granitic plutons in the northern Ya-Gan fault zone, North Alxa, China. The Huhetaoergai pluton is composed of hornblende diorite, medium- to coarse-grained biotite adamellite and coarse-grained biotite adamellite with K-feldspar megacrysts. The U–Pb zircon ages of biotite adamellite are 220.5 ± 1.9 Ma and 226.5 ± 2.4 Ma. These granitoids are I-type granites with highly radiogenic initial ⁸⁷Sr/⁸⁶Sr of 0.708085–0.735470, negative eNd(t) average values of −2.98–3.23 and high eHf(t) of 9–11.05. These features indicate the granitoids were formed from magmas generated from juvenile crust. We speculate that the granitoids of the Huhetaoergai pluton were emplaced during an episode of intense intraplate orogenic movement evolution in an extrusional setting after a period of extensional postcollisional intraplate evolution.

Piezoelectric properties are of significant importance to medical ultrasound, actuators, sensor, and countless other device applications. The mechanism of piezoelectric properties can be deeply understood from structure evolutions. In this paper, we report a diagram of structure evolutions of the Pb(Zn1/3Nb2/3)0.91Ti0.09O3 (PZN-9PT) single crystal with excellent piezoelectric properties among the orthorhombic, tetragonal, and cubic phases with temperature increasing from room temperature to 220 C. Through fitting the temperature dependence XRD curves with Gauss and Lorenz functions, we obtained the evolutions of the content ratio of three kinds of phases (orthorhombic, tetragonal and cubic) and the lattice parameters of the PZN-9PT system with the changes of temperature. The XRD fitting results together with Raman and dielectric spectrums show that the phase transitions of PZN-9PT are a typical continuous evolution process, very similar to the phase transition of paraffin from solid to liquid. Additionally, resonance and anti-resonance spectrum show excellent piezoelectric properties of the crystals, which probably originate from the nano twin domains, as demonstrated by the TEM images. Of particular attention is that the thickness electromechanical coupling factor kt is up to 72%.

Lignocellulosic biomass fractionation is typically performed using methods that are somehow harsh to the environment, such as in the case of the kraft pulping. In recent years, the development of new sustainable and environmentally friendly alternatives has grown significantly. Among the developed systems, bio-based solvents emerge as promising alternatives for biomass processing. Therefore, in the present work, the bio-based and renewable chemicals, levulinic acid (LA) and formic acid (FA), were combined to fractionate lignocellulosic waste (i.e., Maritime pine sawdust) and isolate lignin. Different parameters, such as LA/FA ratio, temperature, and extraction time, were optimized to boost the yield and purity of extracted lignin. The LA/FA ratio was found to be crucial regarding the superior lignin extraction from the waste biomass. Moreover, the increase in temperature and extraction time enhances the amount of extracted residue but compromises the lignin purity and reduces its molecular weight. The electron microscopy images revealed that biomass samples suffer significant structural and morphological changes, which further suggests the suitability of the new developed bio-fractionation process. Same was concluded by the FTIR analysis, in which no remaining lignin was detected in the cellulose-rich fraction. Overall, the novel combination of bio-sourced FA and LA has shown to be a very promising system for lignin extraction of high purity from biomass waste, thus contributing to extend the opportunities of lignin manipulation and valorisation into novel added-value biomaterials.

The food additive sorbic acid is considered as an effective preservative for certain cereal products, and propionic acid is commonly added in bakery wares, e.g. bread and fine bakery wares. The aim of this study is to develop and validate a new nuclear magnetic resonance spectroscopy (¹H NMR) method for routine screening and quantification of sorbic and propionic acids in bread and several bakery products for quality control purposes. Results showed that none of the screened samples contained higher concentrations than regulatory maximum limits. However, for some samples, labelling of preservatives was lacking or they were used in food categories, for which the use is not approved. It can be concluded that the developed NMR method can be used for routine screening of bakery products.

Sulfonated carbon was used as an efficient and reusable heterogeneous solid acid catalyst for the synthesis of biodiesel via esterification of oleic acid with methanol under high voltage conditions. Using an inexpensive and reusable catalyst, environmental benignity, excellent yields in short times, synthesis in atmospheric pressure and low temperature conditions are some of the important features of this protocol. In the final results were confirmed by GC.

Ageing is associated with a decline in both Nrf2 activity and DNA repair efficiency, leading to the accumulation of DNA damage and an increased risk of cancer. Understanding the mechanisms behind the increased level of damaged DNA during ageing is crucial for developing interventions to mitigate age-related cancer risk and improve overall health in older individuals. (Poly)phenols are plant-derived bioactive compounds that undergo metabolism into simpler phenolic catabolites following ingestion. While these compounds have been associated with various health benefits, further analysis of their bioavailable catabolites is necessary. To this end, four phenolic catabolites derived from colonic microbiota were investigated for their ability to reduce DNA damage in response to oxidative challenge and modulate the Nrf2-Antixoidant Response Element pathway. Normal and adenocarcinoma colonocyte cell lines (CCD 841 CoN, & HT29 respectively) were exposed to sub cytotoxic concentrations (>10 µM,) of hydroxylated (4-hydroxybenzoic acid, 3-(3’-hydroxyphenyl) propionic acid) and non-hydroxylated (benzoic acid or 3-phenylpropionic acid) phenolic acids. Using the COMET assay, each catabolite demonstrated significant (p<0.001) geno-protective activity, albeit with varying potency. They also significantly modulated expression of key genes in the Nrf2-ARE pathway, including Nrf2, Heme oxygenase-1 (HO-1), and NAD(P)H dehydrogenase quinone 1 (NQO1). Hydroxylation of the phenolic acids appeared to have a limited effect with respect to bioactivity. Overall, the colon derived phenolic metabolites, when assessed at physiologically relevant concentrations, reduced DNA damage in both normal and adenocarcinoma colonic cells in response to oxidative challenge, mediated – at least in part via upregulation of the Nrf2-ARE pathway.

Oxalate is a divalent organic anion that has implications across many biological and commercial processes. It is derived from plant sources, such as spinach, rhubarb, tea, cacao, nuts, and beans, and therefore is commonly found in raw or processed food products. Oxalate can also be made endogenously by humans and other mammals as a byproduct of hepatic enzymatic reactions. It is theorized that oxalate is useful for plants to store calcium and protect against herbivory. Clinically, oxalate is best known to be a major component of kidney stones, which commonly contain calcium oxalate crystals. Oxalate can induce an inflammatory response that decreases the immune system’s ability to remove renal crystals. When formulated with platinum as oxaliplatin (an anticancer drug), oxalate has been proposed to cause neurotoxicity and nerve pain. There are many sectors of industry that are hampered by oxalate, and some that depend on it. For example, calcium oxalate is troublesome in the pulp industry and the alumina industry as it deposits on machinery. On the other hand, oxalate is a common active component of rust removal and cleaning products. Due to its ubiquity, there is interest in developing efficient methods to quantify oxalate. Over the past four decades several diverse methods have been reported. These approaches include electrode-based detection, liquid chromatography or gas chromatography coupled with mass spectrometry, enzymatic degradation of oxalate with oxalate oxidase and detection of hydrogen peroxide as a product, and indicator displacement-based methods employing fluorescent or UV light-absorbing compounds. It has become clear that no single method will work best for every purpose. This review describes the strengths and limitations of each method, and may serve as a reference for investigators to decide which approach is most suitable for their work.

Hyaluronic acid, known also as hyaluronan, is the most abundant glycosaminoglycan in the extracellular matrix. It is produced by most of the cells in the human body, possibly contributing to various fundamental biological processes. This prompts interest in its therapeutic value. Hyaluronic acid (HA) has been used for various treatments owing to its broad range of properties in medical and dental field specially in periodontology. The review gives an overview on the effects of HA on fibroblasts, bone, wound healing, periodontal regeneration, aphthous ulcer/stomatitis and stem cells. Outcomes of including Hyaluronic acid in non-surgical periodontal therapy, drug delivery system and surgical procedures such as root coverage, papilla regeneration, root conditioning, intrabony defects, guided tissue regeneration are rather optimistic. HA has shown astounding potential in treating periimplantitis. Newer frontiers have to be explored to comprehend the other promising properties of HA. Keyword – Hyaluronic Acid, Periodontology.

Legumes are a diverse and important group of plants that play a vital role in agriculture, food security, and environmental sustainability. Rhizobia are symbiotic bacteria that form nitrogen-fixing nodules on legume roots, providing the plant with a valuable source of nitrogen. Phenolic acids are a group of secondary metabolites produced by plants that have a wide range of biological functions, including defense against pests and diseases, tolerance to abiotic stresses, and nutrient uptake. In the context of climate change and the imperative for sustainable agriculture, this study delves into the dynamic responses of legume species to varying light intensities and their intricate interactions with soil microorganisms. We investigated the impact of light intensity and rhizobial inoculation on the biomass, nitrate reductase, acid phosphatase, and production of phenolic acids in the roots of four legume species, Trifolium repens, Vicia sativa, Ornithopus compressus, and Coronilla juncea. Plants were grown under three light intensity regimes (low, medium, and high) and inoculated with either rhizobia or a non-inoculated control. The results highlights that shaded-light-adapted species, T. repens and V. sativa, increased root exudate production when exposed to high light intensity. This response aligns with their mining strategy, effectively allocating resources to optimize nutrient acquisition under varying conditions. In contrast, species hailing from well- illuminated environments, O. compressus and C. juncea, displayed distinct strategies by significantly increasing biomass under high irradiance, capitalizing on the available light and nutrients. The mining strategy of legumes emerged as a central theme, influencing biomass production, nitrogen dynamics, and enzymatic activities. The strong correlations between biomass and total nitrogen accumulation underscore the role of the mining strategy in efficient nutrient acquisition. Inoculated plants, which rely more on biological nitrogen fixation (BNF), exhibited lower δ15N values, indicative of a successful mining strategy to acquire and utilize atmospheric nitrogen. Enzymatic activities and phenolic acids exhibited significant interspecies variations, reflecting the adaptability of legumes to different light conditions. The findings of this study could be used to develop new strategies for improving legume stress tolerance, nutrient uptake capacity, and rhizosphere health.

We present synthetic experiments of lactic acid (LA) polycondensation to produce poly(lactic acid) (PLA), as well as kinetic modeling calculations that capture the polymer molecular weight increase with time, given the initial concentrations. Tin-octoate-catalyzed polycondensation of (D,L)- or L-lactic acid, was carried out in pre-dried toluene after azeotropic dehydration for 48-120 hours at 130-137 °C. The polymerization was optimized by varying lactic acid and catalyst concentrations as well as the temperature. Gel Permeation Chromatography was used to experimentally follow the evolution of molecular weights and the products were characterized by NMR, TGA, DSC and IR. Under optimal conditions, PLLA with weight-average molecular weight (Mw) of 161 kDa could be obtained. The rate equations that describe polycondensation kinetics were recast in a condensed form that allowed very fast numerical solution and calculation of the number-average molecular weight with time. Deviations with respect to the experiment were minimized in a least-squares fashion, to determine rate constants. The optimized kinetics parameters are shown to reproduce the experimental data accurately

Coffee is one of the most popular beverages in the world. Annual coffee consumption continues to increase, but at the same time, it generates a large amount of spent coffee grounds from the brewing process, that arises environmental problems. An appropriate solution to manage these spent coffee grounds becomes crucial. Our project aims to discuss the feasibility of utilizing the spent coffee ground to synthesize polylactic acid as a recycling application for spent coffee ground. This paper will discuss the properties and potential recycling applications of spent coffee grounds, the brief production process of polylactic acid, and the potential process for converting spent coffee ground to lactic acid. From our review, it is feasible to utilize spend coffee ground as the primary sources for lactic acid production by bacteria fermentation, and further produce bioplastics, polylactic acids by ring-opening polymerization. Possible ways to improve the yield and corresponding cost analysis are also discussed.

Plants are constantly exposed to a variety of different environmental stresses, including drought, salinity, and elevated temperatures. These stress cues are assumed to aggravate in the future driven by the global climate change scenario which we are currently experiencing. These stressors have largely detrimental effects on plant growth and development and, therefore, put global food security in jeopardy. For this reason, it is necessary to expand our understanding of the underlying mechanisms by which plants respond to abiotic stresses. Especially boosting our insight into the ways by which plants balance their growth and their defense programs appears to be of paramount importance, as this may lead to novel perspectives that can pave the way to increase agricultural productivity in a sustainable manner. In this review, our aim was to present a detailed overview of different factettes of the crosstalk between the antagonistic plant hormones abscisic acid (ABA) and auxin, two phytohormones that are the main drivers of plant stress responses, on the one hand, and plant growth, on the other.

Acid fracturing simulation is used widely to optimize carbonate reservoirs and improve acid fracturing treatment performance. In this study, a method was used to minimize the risk of the acid fracturing treatment. First, optimal fracture geometry parameters with UFD methods are calculated. After that, design components change as long as fracture geometry parameters reach their optimal values. The results showed a high flow rate needed to achieve optimal fracture geometry parameters with increasing acid volume. Sensitivity analysis was performed on controllable and reservoir parameters. It observed that a high flow rate should be applied for a low fluid viscosity to achieve the optimization goals. Straight acid reaches optimal conditions at a high flow rate and low volume. These conditions for retarded acids appear only at a low flow rate and high volume. The study of the acid concentration for gelled acid showed that as it increased, the flow rate and volume increased. Besides, for low permeability formation, a large fracture half-length and small fracture width are desirable. In this case, a higher flow rate will be required. The sensitivity analysis showed that the optimum flow rate and acid volume increase and decrease for the high Young's modulus. The effect of closure stress was also investigated and observed for a sample with high closure stress, low flow rate, and high acid volume are required.

Tea and coffee are the most commonly used beverages throughout the world. Both decoctions are rich in small organic molecules such as phenolics/polyphenolics, purine alkaloids, many methylxanthines, substituted benzoic and cinnamic acids. Many of these molecules are physiologically chemopreventive and chemoprotective agents against many severe conditions such as cancer, Alzheimer, Parkinsonism, inflammation, sleep apnea, cardiovascular disorders, bradycardia, fatigue, muscular relaxation, and oxidative stress. Caffeine, a purine alkaloid, is a common metabolite of both tea and coffee aqueous decoctions and its concentration in tea/coffee depends on the fermentation process, preparation of the water extract and quality of tea leaves/coffee beans. A 250 ml of a coffee cup contains 100-150 mg caffeine while the same volume of strong tea contains 25-40 mg caffeine. The present paper presents the potential of caffeine as a potent chemopreventive agent that can be used for numerous physiological disorders.

In the last decades, cultivation of chia (Salvia hispanica L.) has expanded around the world and the seeds have become well known due to their rich composition in nutrients and bioactive compounds. The aim of this work was to evaluate the physical, chemical and nutritional profile of eight chia seeds grown in different Latin-American countries (Argentina, Bolivia, Chile, Ecuador, Mexico, Paraguay and Peru). The results showed that several nutritional parameters such as the protein content and amino acid profile, dietary fiber content, lipid content, mineral composition and phytate present in the seeds depend on the location they were grown in. Other parameters such as ash content, fatty acid profile or physical parameters were uniform across locations (except for color parameters). The results support the notion that nutritional characteristics of seeds are determined by the seed's origin, further analysis is needed to define the exact mechanisms that control the changes in the seeds nutritional properties.

Ecuador is the world's fifth largest cocoa producer, generating hundreds of annual tons of residues from this fruit. This research aims to value this residual (cocoa pod husk) by using it as raw material to obtain pectin, which is widely used in the food and pharmaceutical industries. For them, the extraction of three different organic acids with GRAS status (and therefore safe for their use), citric, malic and fumaric acids, were studied. In addition, two other factors, temperature (70-90°C) and extraction time (60-90 min), were explored in a central composite design of experiments. Under the conditions of the experiment, it was obtained that the best yields were reached for citric acid, malic acid and fumaric acid and for ~86 min of extraction time. The temperature did not show a significant influence on the yield. The pectins obtained under optimal conditions were characterised, showing their similarity with commercial pectin. However, the equivalent weight and the esterification degree of the pectin obtained with fumaric acid classify it as having a high equivalent weight and a low degree of esterification. It differs significantly from the other two acids, perhaps due to the limited solubility of fumaric acid.

The rise in prevalence of obesity in women of reproductive age in both developed and developing countries might propagate intergenerational cycles of detrimental effects on metabolic health, contributing to substantial economic burden on society. Placental lipid metabolism might be disrupted by maternal obesity, which possibly affects the life-long health of the offspring. Here, we investigated placental lipid metabolism and handling from women with pre-gestational obesity as a sole pregnancy complication and compared to placental responses of lean women. Open profile and targeted lipidomics were used to assess placental lipids and oxidized products of docosahexahenoic acid (DHA), neuroprostanes, and arachidonic acid (AA), isoprostanes. Placental fatty acid transporters FABP1, FABP3 and endothelial lipase protein were measured. Despite no signs of overall alterations in lipid content, increased contents of DHA, AA, DHA-derived neuroprostanes and AA-derived isoprostanes and decreased content of FABP1 protein were found in placentas from obese women. Multivariate analyses suggested that these oxidised fatty acids are associated with maternal and placental inflammation and also with birth weight. These results might shed light on the molecular mechanisms associated with altered fatty acid metabolism and lipid handling in maternal pre-gestational obesity, placing these oxidized fatty acids as novel mediators of placental function.

Thai basil is a renowned medicinal plant and a rich source of bioactive antioxidant compounds having several health benefits, with actions to prevent of cancer, diabetes and cardiovascular disease. Plant cell and tissue culture technologies can be routinely established as an important, sustainable and low-cost biomass source for the production of high-value phytochemicals. The current study aimed at developing an effective protocol for the production of Thai basil leaf derived callus cultures with sustainable and high production of biomass and antioxidants as an alternative of leaves production. MS basal medium with various concentrations of plant growth regulators (PGRs) compatible with nutraceutical applications (i.e., gibberellic acid (GA3) and 6-benzylaminopurine (BAP) either alone or in combination with naphthalene acetic acid (NAA)) were evaluated. Among all tested PGRs, the combination BAP:NAA (5 mg/L:1 mg/L) yield maximum biomass accumulation (fresh weight (FW): 190 g/L and dry weight (DW): 13.05 g/L) as well as enhanced phenolic (346.08 mg/L) production. HPLC quantification analysis indicated high productions of chicoric acid (35.77 mg/g DW) and rosmarinic acid (7.35 mg/g DW) under optimized callus culture conditions. Antioxidant potential was assessed using both in vitro cell free and in vivo cellular antioxidant assays. Maximum in vitro antioxidant activity DPPH (93.2 % of radical scavenging activity) and ABTS (1322 µM Trolox equivalent antioxidant capacity) was also observed for the extracts from callus cultures grown on optimal conditions. In vivo cellular antioxidant activity assay confirmed the effective protection against oxidative stress of the corresponding extract by the maximum inhibition of ROS and RNS production. Compared to commercial leaves, callus extracts showed higher production of chicoric acid and rosmarinic acid associated with higher antioxidant capacity. In addition, this biological system also has a large capacity for continuous biomass production, thus demonstrating its high potential for possible nutraceutical applications.

Zircon xenocrysts from alkali basalts in Ratanakiri Province, Cambodia, represent a unique low-Hf zircon, within a 12,000 km long Indo-Pacific megacryst zone. Colourless, yellow, brown and red crystals ({100}, {101}, subordinate {211}, {1103}), with hopper growth and corrosion features, range up to 20 cm in size. Zircon chemistry implicates juvenile, Zr-saturated, mantle-derived alkaline melt (Hf 0.6–0.7 wt%, Y <0.2 wt%, U+Th+REE <600 ppm, Zr/Hf 66–92, Eu/Eu*_N ~ 1, positive Ce/Ce*_N, HREE enrichment). Incompatible element depletion with increasing Yb/Sm_N from core to rim at ~ constant Hf suggests single stage growth. Ti-in-zircon temperatures (~570–740 °C) are lower than predicted by crystal morphology (800–900 °C) and decrease from core to rim (D_T = 10–50 °C). The d¹⁸O values (4.88 to 5.01‰ VSMOW) are relatively low for xenocrysts from the zircon Indo-Pacific zone (ZIP). The ¹⁷⁶Hf/¹⁷⁷Hf values (+ εHf 4.5–10.2) give T_{Depleted Mantle} model source ages of 260–462 Ma and T_Crustal ages of 391–754 Ma. The source magmas reflect variably depleted lithospheric mantle with little supracrustal input. Zircon U-Pb (0.88–1.56 Ma) and (U-Th)/He (0.86–1.02 Ma) ages are older than host basalt ages (~0.7 Ma), suggesting limited residence before transport. Zircon genesis suggests Zr-saturated, Al-undersaturated, carbonatitic-influenced, low-degree partial melting (<1%) of peridotitic mantle at ~60 km beneath the Indochina terrane.

Lysophosphatidic acid (LPA) type 3 (LPA3) receptor mutants were generated in which the sites detected phosphorylated were substituted by non-phosphorylatable amino acids. Substitutions were made in the intracellular loop 3 (IL3 mutant), the carboxyl terminus (Ctail), and both domains (IL3/Ctail). The wild-type (WT) receptor and the mutants were expressed in T-REx HEK293 cells, and the consequences of the substitutions were analyzed employing different functional parameters. Agonist- and LPA-mediated receptor phosphorylation was diminished in the IL3 and Ctail mutants and essentially abolished in the IL3/Ctail mutant, indicating that the main sites were substituted and distributed in both domains. The WT and mutant receptors increased intracellular calcium and ERK 1/2 phosphorylation in response to LPA and PMA. An increase in baseline ERK phosphorylation was detected in the IL3/Ctail mutant. LPA and PMA-induced receptor interaction with β-arrestin 2 and LPA3 internalization were severely diminished in the mutants. Mutant-expressing cells also exhibit increased baseline proliferation and response to different stimuli, which were inhibited by the antagonist Ki16425, suggesting a role of LPA receptors in this process. Migration in response to different attractants was markedly increased in the Ctail mutant, which the Ki16425 antagonist also attenuated.

The host glycosylation mechanism synthesizes the carbohydrates of glycoproteins of viral envelopes. Due to the loss of the Cytidine Monophospho-N-Acetylneuraminic Acid Hydroxylase gene by some mammalian species, including humans (negative-CMAH), Neu5Gc is no longer synthesized. Uptake of Neu5Gc by negative-CMAH species, through the intake of food products derived from positive-CMAH mammals, leads to incorporating Neu5Gc-glycans in the glycocalyx (xenosialylation). Neu5Gc, being a Mammalian-associated Carbohydrate Antigen (MCA), acts as a non-self-antigen, inducing an inflammatory reaction (Xenosialitis), and triggering the production of circulating antiNeu5Gc antibodies to attack/remove all incorporated Neu5Gc. In the state of Xenosialitis, the virus-neutralizing antibodies produced by a heavily xenosialylated patient following exposure to viral infection (including SarsCoV2) or anti SarsCoV2 vaccination cross-react against all incorporated non-self Neu5Gc-MCA glycans due to their resemblance with viral envelope antigens synthesized by the host glycosylation mechanism. In addition, the circulating anti-XeSias antibodies determine the massive removal of the circulating neutralizing FC-xeno-contaminated antibodies by the serum, living only the hyper-inflammatory agalattosylated antiviral IgG antibodies. Therefore, we hypothesize that the combination of antibody cross-reaction against non-self Neu5Gc-MCA glycans and the massive removal of the xeno-contaminated newly formed neutralizing antibodies in favor of hyper reactive antibodies, could be the cause of the massive inflammatory reaction (cytokine storm, coagulopathies, neuropathies) observed in Covid 19 patients or after anti-SarsCoV2 vaccination. This analysis is an invitation to investigate the post-infectious and/or post-vaccination adverse phenomena in the light of xenosialization as a key to understanding the severe post viral and post vaccine complications, including SARS-CoV2 infection or related vaccination.

To study the fermentation process of biocatalyzing decanoic acid to synthesize trans-2-decenoic acid, this study was based on the engineering E.coli constructed in the laboratory in the early stage and studied the effect of seed liquid culture time, culture temperature, inoculum amount, induction temperature, dissolution effects of substrate solvent, metal ions, and substrate loading on the yield of trans-2-decenoic acid. Based on single-factor experimental optimization, the Box–Behnken design was used to conduct response surface testing using the substrate feeding concentration, inducer concentration, and MnCl2 concentration as response variables and trans-2-decenoic acid production as the response value. The optimal fermentation process was determined through experiments: seed culture time 20 h, culture temperature 37°C, inoculation amount 1%, induction temperature 30°C, substrate flow amount 0.15 g/L, inducer concentration 5.60 g/L, MnCl2 concentration was 0.10 mM. Under these conditions, the average production of trans-2-decenoic acid was 1.982 ± 0.110 g/L. Compared with the basic LB medium, the production of trans-2-decenoic acid increased by 1.042 g/L; compared with the previous period, the yield of trans-2-decenoic acid studied increased by 1.501 ± 0.110 g/L, which provides a reliable basis for further research on the fermentation process of biocatalytic decanoic acid synthesis of trans-2-decenoic acid.

Pentadecanoic acid (C15:0) is an essential odd-chain saturated fatty acid with broad activities relevant to protecting cardiometabolic, immune, and liver health. C15:0 activates AMPK and inhibits mTOR, both of which are core components of the human longevity pathway. To assess the potential for C15:0 to enhance processes associated with longevity and healthspan, we used human cell-based molecular phenotyping assays to compare C15:0 with three longevity-enhancing candidates: acarbose, metformin, and rapamycin. C15:0 (n=36 activities in 10 of 12 cell systems) and rapamycin (n=32 activities in 12 of 12 systems) had the most clinically relevant, dose-dependent activities. At their optimal doses, C15:0 (17 µM) and rapamycin (9 µM) shared 24 activities across 10 cell systems, including anti-inflammatory (e.g., lowered MCP-1, TNFɑ, IL-10, IL-17A/F), antifibrotic, and anticancer activities, which are further supported by previously published in vitro and in vivo studies. Paired with prior demonstrated abilities for C15:0 to target longevity pathways, hallmarks of aging, aging rate biomarkers, and core components of type 2 diabetes, heart disease, cancer, and nonalcoholic fatty liver disease, our results support C15:0 as an essential nutrient with activities equivalent to, or surpassing, leading longevity-enhancing candidate compounds.

This study examines the behavior of stearic acid (SA) and 12-hydroxystearic acid (12-HSA) aqueous mixtures as a function of temperature and 12-HSA/SA molar ratio (R). Whatever R, the system exhibits a morphological transition at a given threshold temperature, from multilamellar self-assemblies at low temperature towards small micelles at high temperature, as shown by a combination of transmittance measurements, Wide Angle X-ray diffraction (WAXS), small angle neutron scattering (SANS) and differential scanning calorimetry (DSC) experiments. Such transition originates from the melting of the crystallized fatty acids within the lamellar phase. The precise determination of the threshold temperature, which ranges between 20°C and 50°C depending on R, allows for the construction of the whole phase diagram of the system as a function of R. At high temperature the micelles that are formed are oblate for pure SA solutions (R = 0) and prolate for pure 12-HSA solution (R = 1). In the case of mixtures, there is a progressive continuous transition from oblate to prolate shape when increasing R, with micelles that are almost purely spherical for R = 0.33.

Ludwigia octovalvis (Jacq.) P.H. Raven is widely used in traditional medicine for different illnesses included diabetes and hypertension. However, its impact on lipotoxicity and metabolic syndrome in vivo has not been addressed. Therefore, the aim of this study was to evaluate the effects of this plant on the metabolic syndrome parameters in a C57BL6J mouse hypercaloric diet model. L. octovalvis hydroalcoholic extract and its ethyl acetate fraction (25 mg/kg/day) were used for sub-chronic assessment (10 weeks). Also four subfractions (25 mg/kg) were evaluated in the postprandial triglyceridemia test in healthy C57BL6J mice. The hydroalcoholic extract and ethyl acetate fraction significantly decreased body weight gain (-6.9 g and -1.5 g), fasting glycemia (-46.1 and -31.2 mg/dL), systolic (-26.0 and -22.5mmHg) and diastolic (-8.1 and 16.2 mmHg) blood pressure, free fatty acid concentration (-13.8 and -8.0 μg/mL) and insulin-resistance (measured by TyG index, -0.207 and -0.18) compared to the negative control. Postprandial triglyceridemia test showed that the effects in the sub-chronic model are due, at least in part, to improvement in this parameter. L. octovalvis treatments, particularly the hydroalcoholic extract, improve MS alterations and decrease free fatty acid concentration. These effects are possibly due to high contents of corilagin and ellagic acid.

We describe the behavior of mixtures of stearic acid (SA) and its hydroxylated counterpart 12-hydroxystearic acid (12-HSA) in aqueous mixtures at room temperature, as function of the 12-HSA/(fatty acid) mole ratio R. The morphologies of the self-assembled aggregates are obtained by a multi-structural approach that combines confocal and cryo-TEM microscopies with Small-Angle Neutron Scattering (SANS) and Wide-Angle X-Rays Scattering (WAXS) measurements, coupled with rheology measurements. Fatty acids are solubilized by an excess of ethanolamine counterions, so that their heads are negatively charged. The behavior is driven by the competition between mixing entropy and enthalpic effects. A clear trend towards partitioning between the two types of fatty acids is observed, presumably driven by the favorable formation of a H-bond network between hydroxyl OH function on the 12th carbon. For all R, the self-assembled structures are locally lamellar, with bilayers composed of crystallized and strongly interdigitated fatty acids. At high R, multi-lamellar tubes are formed, similarly as for pure aqueous solutions of 12-HSA. The doping by a low amount of SA molecules only slightly modify the dimensions of the tubes (radius and length), and slightly decreases the bilayers rigidity. The solutions have a gel-like behavior originating from entanglements between tubes and show a yield stress. At intermediate R, a partial local partitioning occurs between the two types of fatty acids. The tubes coexist in solution with helical ribbons. The two structures possibly merge to form very long snaky objects with straight and curved parts. The rigidity of the bilayers and the rheological behavior of the solutions are very similar to those of the high R case. At low R, local partitioning also occurs, and the architecture of the self-assemblies associates the two morphologies of the pure fatty acids systems, respectively 2-D planar bilayers for SA and the tubes describe above for the 12-HSA molecules: they are facetted objects with planar domains enriched in SA molecules, capped with curved domains enriched in 12-HSA molecules. The rigidity of the bilayers is strongly increased, as well their storage modulus, compared to systems with larger R. The solutions remain however viscous fluids in this regime of low R.

Cholestasis is a condition defined as an abnormal decrease of bile flow due to progressive pathological states or cholestatic liver diseases that affect the biliary tree at intrahepatic and extrahepatic level. It induces complications such as cirrhosis, liver failure, malignancies, pruritus, fatigue, bone disease and nutritional deficiencies that merit close follow-up and specific interventions to improve quality of life. Furthermore, cholestasis can progress to end-stage liver disease and represents an entity with high morbidity and mortality; and economic burden, Therefore, it is important that clinicians understand the treatment options for cholestatic liver diseases. This review addresses the pathophysiology of cholangiopathies, a general view of current treatments and their molecular targets, and a specific review of those groups of drugs. The objective is to provide clinicians with an overview of the current treatment of cholangiopathies based on evidence on its efficacy and safety.

A new pathway leading to the n-10 fatty acid series has been recently evidenced, starting from sapienic acid - a monounsaturated fatty acid (MUFA) resulting from the transformation of palmitic acid by delta-6 desaturase. Sapienic acid attracts attention as novel marker of cancer cell plasticity. Here, we analyzed fatty acids including the n-10 fatty acid contents, and compared for the first time cell membranes and the corresponding extracellular vesicles (EV) of two human prostatic adenocarcinoma cell lines of different aggressiveness (PC3 and LNCaP). The n-10 components were 9-13% of the total fatty acids in both cancer cell lines and EVs, with total MUFA levels significantly higher in EVs of the most aggressive cell type (PC3). High sapienic/palmitoleic ratios indicated the preference for delta-6 vs. delta-9 desaturase enzymatic activity in these cell lines. The expressions analysis of enzymes involved in desaturation and elongation by qRT-PCR showed a higher desaturase activity in PC3 and a higher elongase activity toward polyunsaturated fatty acids than toward saturated fatty acids, compared to LNCaP cells. Our results improve the present knowledge in cancer fatty acid metabolism and lipid phenotypes, highlighting EV lipidomics to monitor positional fatty acid isomer profiles and MUFA levels in cancer.

Uric acid being a diagnostic biomarker of gout and therapeutic agent in homeopathic medicines necessitates to develop simple and specific method for its determination. Therefore, present study describes the development and validation of simple and specific colorimetric method for determination of uric acid in homeopathic tablets. Uric acid upon reaction with acid and reagent mixture produced coloured derivative which was detected at 411 nm. The method was found linear over the whole range investigated with the correlation coefficient (R²) = 0.9975. Beer’s law was obeyed over the concentration ranges from 5.0 µg/mL to 240 µg/mL. The method was found to be reliable (95.7 to 108.2% recovery), repeatable intra-day accuracy (97.01 to 107.4%) and reproducible-inter day accuracy (99.45 to 107.8%) with relative standard deviation less than 5%. The results of the present study indicate the method is easy to perform, specific and suitable to be used for the determination of uric acid in homeopathic Acid Uric Tablet using less expensive derivitization.

The direct Cr (VI) reduction process by oxalic acid was conducted and the results showed that the Cr (VI) was efficiently reduced by oxalic acid at high reaction temperature and high dosage of oxalic acid. The reduced product, Cr (III), was easily generated stable complex compounds (Cr(HC2O4)3) with oxalate, which displayed a negative effect on the reduction process. The high reaction temperature and high acidic medium could destroy the stable structure of a complex compound to release oxalate, and facilitate the reduction of Cr (VI). Generally, the present study provided a versatile strategy for Cr (VI) reduction, exhibiting a bright application future for real wastewater treatment.

The research progress of nano-hydroxyapatite and its composite biomaterials, which are widely used, is summarized. The preparation techniques and applications of nano-hydroxyapatite and its composites in tissue engineering scaffolds, sustained and controlled release drug carriers, targeting drug delivery and environmental functional materials show that nano-hydroxyapatite and its composites will have good prospects in the field of biomedicine. The nano-hydroxyapatite composite biomaterial is a first phase or multi-phase material added to the nano-hydroxyapatite to obtain a favorable histological reaction, satisfactory strength and rigidity, and to synthesize a scaffold material for tissue regeneration. As a scaffold for guiding bone tissue regeneration, nano-hydroxyapatite composite material can also be used as a targeted drug release system for drug delivery system. It has good biocompatibility and degradability and has become a research hotspot in bone tissue engineering. The complex is expected to be applied to medical diagnostic fields such as tumor cell detection and nano biological probes.

LPA3 receptors were expressed in TREx HEK 293 cells, and their signaling and phosphorylation were studied. The agonist, lysophosphatidic acid (LPA), increased intracellular calcium and ERK phosphorylation through pertussis toxin-insensitive processes. Phorbol myristate acetate, but not LPA, desensitizes LPA3-mediated calcium signaling. The agonists and the phorbol ester-induced LPA3 internalization. Pitstop 2 (clathrin heavy chain inhibitor) markedly reduced LPA-induced receptor internalization; in contrast, phorbol ester-induced internalization was only delayed. LPA induced rapid β-arrestin-LPA3 receptor association. The agonist and the phorbol ester induced marked LPA3 receptor phosphorylation, and phosphorylation sites were detected using mass spectrometry. Phosphorylated residues were detected in the intracellular loop 3 (S221, T224, S225, and S229) and in the carboxyl terminus (S321, S325, S331, T333, S335, Y337, and S343). Interestingly, phosphorylation sites are within sequences predicted to constitute β-arrestin binding sites. These data provide insight into LPA3 receptor signaling and regulation.

This research aimed to synthesize Polyvinyl fluoride (PVDF) membranes and coat them with Tannic acid (TA) nanoparticles and Polyethylene glycol (PEG) additives so that the membrane's removal efficacy for humic acid (HA) pollutant from agricultural wastewater was investigated. Thus, six membranes with PEG:TA ratios of 0:0, 1:0, 0:1, 1:1, 4:1 and 1:4 were synthesized. Then the membranes' characteristics were identified by FT-IR ATR, FESEM, and AFM analysis, and HA's particle size and zeta potential were also investigated. Based on optimizing effective parameters, the operating pressure of 1.5 bar and HA concentration of 80 ppm were selected as optimal values. The membrane with PEG:TA=4:1, as the optimally modified membrane, had a pure water flux of 446.03 L/m2.h, effluent flux of 72.43 L/m2.h and pollutant removal rate of 86.62% at pH=7 After 60 min had passed. These values for the pristine membrane (PEG:TA=0:0) were 265.64 L/m2.h, 89.39 L/m2.h, and 75.59%, respectively. The results showed that although the effluent flux was lower in the optimized modified membrane than in the pristine membrane, HA removal percentage was increased.

Fruit cracking or splitting, a severe physiological disease that highly affects appearance and quality, compromise the commodity value of fruit and also causes huge economical losses to the producers of several fleshy fruit crops. The growth-promoting phytohormone gibberellic acid (GA) and growth-inhibiting phytohormone abscisic acid (ABA) antagonistically regulate numerous developmental processes throughout the plant life cycle. Homeostasis of endogenous GA and ABA play a significant role in the normal growth of fruits, and its imbalance may lead to the occurrence of cracking or splitting during the process of fruit growth, development, ripening and postharvest storage. The pathways of GA and ABA metabolism and signaling have been studied widely, and the major components were well characterized, which including the genes encoding major biosynthesis and catabolism enzymes and the key signaling components. Nevertheless, our knowledge of the mechanisms of GA and ABA governing fruit cracking is not comprehensive enough. In this review, we not only focus on the scenarios of effects of endogenous GA and ABA contents in the fruit and exogenous plant growth regulators GA and ABA treatments, but also endeavor to provide some genetic cues on the function of GA and ABA responsible for fruit cracking modulation. Information from this review aims to strengthen the understanding of potential molecular bases underlying GA and ABA in fruit cracking control and provide guidance in breeding of fruit cultivars with cracking-resistant ideotypes, and also make great theoretical significance in guiding the establishment of integrated prevention and control measures to fruit cracking or splitting.

A key response to glucose stress is an increased production of unsaturated fatty acids to balance the increase of saturated fatty acids in the membrane. The C. elegans homolog of stearoyl-CoA desaturase, FAT-7, introduces the first double bond into saturated C18 fatty acids yielding oleic acid and is a critical regulatory point for surviving cold and glucose stress. Here, we incorporated 13C stable isotopes into the diet of nematodes and quantified the 13C-labelled fatty acid by GC-MS and HPLC/MS-MS to track the metabolic response to various concentrations of glucose. Previous work has analyzed membrane composition of C. elegans when responding to mild glucose stress and showed few alterations in overall fatty acid composition in the membrane. Here, in nematodes exposed to higher concentrations of glucose, a specific reduction of oleic acid and linoleic acid was observed. Using time courses and stable isotope tracing, the response of fatty acid me-tabolism to increasing levels of glucose stress has been characterized, revealing a funneling of monounsaturated fatty acids to preserve polyunsaturated fatty acid abundance. Taken together, higher levels of glucose unveil a specific reduction of oleic and linolenic acid in the metabolic re-wiring required to survive glucose stress.

Chiral hydroxamic acid (HA) and bis-hydroxamic acid (BHA) ligands have made significant contributions to the field of asymmetric synthesis, particularly in the synthesis of natural products. These ligands possess unique molecular structures that allow for exceptional stereochemical control, leading to their widespread use in catalytic systems. This review highlights the advancements made in asymmetric synthesis using chiral hydroxamic acid and bis-hydroxamic acid ligands and their impact on the synthesis of complex natural products. The discussion encompasses their role in enantioselective C-C bond formation, the functionalization of C-H bonds, asymmetric transformations involving heteroatoms, and their application in the total synthesis of natural products. The versatility and efficiency of chiral hydroxamic acid ligands and bis-hydroxamic acid ligands make them invaluable tools for synthetic chemists working towards the efficient and selective synthesis of natural products. This review provides a comprehensive overview of their contributions, showcasing their potential to expand the boundaries of chemical synthesis and access the diverse array of natural product scaffolds.

We investigated whether cigarette smoking and dietary acid load (DAL) are associated with the risk of chronic obstructive pulmonary disease (COPD) in middle-aged healthy Korean men. Healthy men without diagnosed chronic disease (40-64 yrs) from the KNHANES-VI (2013–2015) included in the analysis (n=774) were subdivided by smoking status and DAL levels as estimated by the net endogenous acid production (NEAP) quartile. Current smokers tended to have a higher risk of COPD than non-smokers before and after the adjustment. When divided by the DAL quartile, the Q4 tended to have a higher risk of COPD than the Q1. Additionally, current smokers with lower (Q2), modest (Q3), and highest NEAP scores (Q4) showed more than 4-fold higher risks of COPD than the non-smokers with the lowest NEAP scores (Q1). Ex–smokers with higher NEAP scores (Q3 and Q4) showed more than 4-fold higher risks of COPD than the Q1. Interestingly, the risk of COPD was also more than 6-fold higher in non-smokers with the highest NEAP scores compared to the Q1. NEAP scores and smoking status synergistically increased the risk of COPD in middle-aged healthy Korean men. It suggests that DAL levels are an important factor for the prevention and management of COPD.

COVID-19 patients suffer from detrimental effects of cytokine storm and not much success has been achieved to overcome this issue. We sought to test the ability of selenium in reducing the impact of two important cytokine storm players; IL-6 and TNF-a. The effects of four selenium compounds were evaluated on the secretion of these cytokines from THP-1 macrophages in vitro following LPS challenge. Also, potential impact of methylseleninic acid (MSeA) on Nrf2 and IkBa was determined following short treatment of THP-1 macrophages. MSeA was observed to be the most potent selenium form to reduce IL-6 and TNF-a levels among the four selenium compounds tested. In addition, an increase in Nrf2 and decrease in pIkBa in human macrophages was observed following MSeA treatment. Our data indicate that COVID-19 patients might benefit by suppressing their cytokine storm with addition of MSeA to the standard therapy.

D-Glucaric acid is an important bio-based building block of polymers and is a high value-added chemical that can be used in a variety of applications. In the present study, the Udh target genes from Pseudomonas putida and Pseudomonas syringae were used together to construct the expression vector pETDuet-2×Udh. The transformants of BL21(DE3) with vector pETDuet-2×Udh was applied to produce glucaric acid from glucuronic acid. After optimization of induction conditions, the highest Udh expression were achieved when 0.4 mmol L-1 isopropyl-β-d–thiogalactoside (IPTG) was added to cell cultures at an OD600 value of 0.6 followed by culture at 26℃ for 6 hours. The production of glucaric acid substantially reached 5.24 ± 0.015 g L-1 in fed-batch cultures in a 30 L tank. In the present study, a new system for glucaric acid production was established, which was more economic and friendly to environment.

Wet anaerobic storage of algal biomass is a promising preservation approach which can ensure continuous supply of these feedstocks to biorefineries year-round. An effective solution to preservation must ensure minimal dry matter loss and change in biochemical composition during storage. Therefore, the objective of this study was to investigate the preservation of Nannochloropsis gaditana biomass through wet anaerobic storage and its impact on biomass quality. Prior to storage, algae sample was inoculated with two different strains of lactic acid bacteria and thereafter stored for 30 and 180 days. Each inoculant limited dry matter loss to &lt;10% (dry basis) after the storage durations. Final pH values (4.3 - 4.8) indicate that the biomass samples were properly ensiled, achieving the acidic conditions necessary for preservation. Compositional analysis of the biomass after storage showed a reduction in carbohydrate content, a relative increase in lipid content, and no significant change to the protein fraction. Glucose and galactose were the prevalent sugar monomers. The low dry matter loss and minimal compositional change indicates that wet anaerobic storage is an effective means of preserving algal biomass, ensuring a constant supply of algal biomass feedstock to a biorefinery.

Glutamate decarboxylase (L-glutamate-1-carboxylase, GAD; EC 4.1.1.15) is a pyridoxal 5-phosphate-dependent enzyme, which catalyzes the irreversible α-decarboxylation of L-glutamic acid to γ-aminobutyric acid (GABA) and CO2. The enzyme is widely distributed in eukaryotes as well as prokaryotes, where it – together with its reaction product GABA - fulfils very different physiological functions. The occurrence of gad genes encoding GAD has been shown for many microorganisms, and GABA-producing lactic acid bacteria (LAB) have been a focus of research during recent years. A wide range of traditional foods produced by fermentation based on LAB offer the potential of providing new functional food products enriched with GABA that may offer certain health-benefits. Different GAD enzymes and genes from several strains of LAB have been isolated and characterized recently. GABA-producing LAB, biochemical properties of their GAD enzymes, and possible applications are reviewed here.

The evolutionary success of land plants largely relies on their ability to cope with constant environmental fluctuations, which negatively impact their reproductive fitness and trigger adaptational responses to biotic and abiotic stresses. In this challenging scenario, comprehensive research efforts so far aimed at depicting the roles of well-known phytohormones, mainly auxins, along with brassinosteroids, jasmonates, and abscisic acid, although the signaling networks coordinating the crosstalk among them remains vaguely understood. Accordingly, this review focuses on the Arabidopsis Amidase Signature (AS) superfamily members, highlighting the hitherto relatively underappreciated functions of AMIDASE1 (AMI1) and FATTY ACID AMIDE HYDROLASE (FAAH), as crucial coordinators of the growth-defense response trade-off by modulating auxin and ABA homeostasis.

Age-related macular degeneration, a leading cause of visual loss and dysfunction in the devel-oped world, is a disease initiated by genetic polymorphisms that impairs negative regulation of complement. Proteomic investigation points to altered glycosylation and loss of SIGLEC medi-ated glyco-immune checkpoint parainflammatory homeostasis as a main determinant for the vi-sion impairing complications of macular degeneration. The effect of altered glycosylation on microglial maintained retinal para-inflammatory homeostasis and eventual recruitment and polarization of peripheral blood monocyte derived macrophages (PBMDM) into the retina can explain the phenotypic variability seen in this clinically heterogenous disease. Restoring gly-co-immune checkpoint control with a sialic acid mimetic nanoparticle targeting microgli-al/macrophage SIGLECs to regain retinal para inflammatory homeostasis is a promising thera-peutic that could halt the progression of and improve visual function in all stages of macular de-generation.

Fine aroma cocoa (Theobroma cacao) is one of Ecuador's most iconic export products, representing 63% of world production; however, few advances have been made in fermentation processes that greatly influence the development of chocolate´s organoleptic characteristics. The study of starter cultures has been investigated in other countries, which seek to improve organoleptic properties or decrease fermentation time. The aim of this study was to analyze the effect of a native microbial consortium based on two yeasts (Torulaspora delbrueckii and Hanseniaspora uvarum), a lactic acid bacterium (LAB) (Lactobacillus plantarum) and an acetic acid bacterium (AAB) (Acetobacter ghanensis) inoculated at the beginning of the fermentative process, on physical and biochemical variables, microbial population dynamics, and percentage of almond fermentation. The started culture caused changes in sugar and acid content, which in turn generated temperature and pH changes in the dough, resulting in the dynamics of yeast, AAB, and mesophilic microorganisms remaining higher than those of the control throughout the fermentation process; a decrease of filamentous fungi that affect the flavor and quality of beans due to the production of acetic acid or secondary metabolites from yeasts and LAB; and optimized fermentation percentage by 24% higher than spontaneous fermentation in only 96 hours.

Amino acid efflux and influx transport systems play vital roles in industrial microorganisms’ cell growth and metabolism. However, although biochemically characterized, most amino acid transporters remain unknown at the molecular level in Bacillus licheniformis. This study focuses on the molecular and functional characterizations of three transporters, YdgF, YvbW, and YveA, mainly when catalyzing the cross-membrane flux of L-Aspartate. When growing in the minimal medium with L-Asp as the only carbon and nitrogen source, the growth of strains lacking proteins YdgF, YvbW, and YveA was significantly inhibited compared with wild-type strains, while supplementing the expression of the corresponding proteins in the single-gene knockout strains can alleviate the inhibition to some extent. Upon overexpression, the recombinant proteins mediate the accumulation of L-aspartate to varying degrees. Compared with wild-type strains, the single knockout strains of the three protein genes exhibited reduced absorption of L-aspartate. In addition, this paper focuses on the effects of these three proteins on the absorption of β-alanine, L-glutamate, D-serine, D-alanine, and glycine.

Foods are mixed with saliva in the oral cavity and swallowed. During staying in the stomach, saliva is contentiously provided to mix with the ingested foods. Because a salivary component nitrite is protonated to produce active nitrous acid at acidic pH, the redox reactions of nitrous acid with phenolic compounds in foods become possible in the stomach. In the reactions, nitrous acid is reduced to nitric oxide (•NO), producing various products from phenolic compounds. In the products, stable hydroxybezoyl benzofuranone derivatives, which are produced from quercetin and its 7-O-glucoside, are included. Caffeic acid, chlorogenic acid, and rutin are oxidized to quinones and the quinones can react with thiocyanic acid derived from saliva producing stable oxathiolone derivatives. 6,8-Dinitrosocatechis are produced from catechins by the redox reaction, and the dinitrocatechins are oxidized further by nitrous acid producing the quinones, which can make charge transfer complexes with the dinitrosocatechin and can react with thiocyanic acid producing the stable thiocyanate conjugates. In this way, various products can be produced by the reactions of salivary nitrite with dietary phenolic compounds, and reactive and toxic quinones formed by the reactions are postulated to be removed in the stomach by thiocyanic acid derived from saliva.