Non-exhaust fine particles such as tires and brakes emitted from vehicles have a significant impact on air pollution and human harm, and regulations on emissions are being discussed in earnest, starting with the introduction of brake wear particles emission standards in Euro 7. Various indoor and outdoor experiments were conducted, such as analysis of the amount of wear on tires and brakes, and analysis of the physical and chemical properties of fine particles, as fundamental data for the introduction of emission standards and the development of low wear tires and brakes to meet regulations. Recently, international standardized indoor experimental methods for brakes have been announced, and indoor and outdoor experimental methods for tires have been continuously studied to develop international standardized methods. In particular, tire-break-road wear particles are usually mixed with each other in the non-exhaust particles from a vehicle driving on real roads, and in-depth research is being performed on the accurate classification and characteristic analysis. In this study, the characteristics of the volatile organic components (VOCs) and marker substances for tire and tire-road wear fine particles were analyzed. A system capable of measuring non-exhaust wear fine particles was installed on the vehicle, and samples were collected from the vehicle running on the two different driving conditions, various constant speeds in the proving ground road and real driving roads. The VOCs contained in tires and tire-road-wear particles (TRWPs) under the specific temperature conditions with a thermogravimetric analyzergas chromatography/mass analysis (TGA-GC/MS). In addition, the correlations between VOCs and tire rubber components were analyzed through marker analysis using pyrolysis-gas chromatography/mass analysis (GC/MS). In VOCs, n-Hexane, n-Dodecane, and 1-Butene were measured relatively much in both constant-speed and real-drive tests. In addition, marker substances of synthetic rubber and natural rubber were not detected in the collected background fine particles.

This manuscript critically reviews the design and delivery of spray-dried particles for the achievement of high total lung doses (TLD) with a portable dry powder inhaler. We introduce a new metric termed the product density, which is simply the TLD of a drug divided by the volume of the receptacle it is contained within. The product density is given by the product of three terms: the packing density (the mass of powder divided by the volume of the receptacle), the drug loading (the mass of drug divided by the mass of powder), and the aerosol performance (the TLD divided by the mass of drug). This manuscript discusses strategies for maximizing each of these terms. Spray drying at low drying rates with small amounts of a shell-forming excipient (low Peclet Number) leads to formation of higher density particles with high packing densities. This enables ultrahigh TLD (>100 mg of drug) to be achieved from a single receptacle. Emptying of powder from capsules is directly proportional to the mass of powder in the receptacle, requiring an inhaled volume of about 1 L for fill masses between 40 and 50 mg and up to 3.2 L for a fill mass of 150 mg.

Developing particles of different anisotropic shapes are the hot topic since decades as they guarantee some special features of properties not possible through other means. Again, controlling atoms to develop certain size and shape particle is a quite challenging job. In this study, gold particles of different shapes are developed via pulse-based electronphoton-solution interface process. Gold atoms of certain transition state develop monolayer assembly at solution surface around the light glow (known in argon plasma) being generated at bottom of copper capillary (known in cathode). The rate of uplifting gold atoms to solution surface is being controlled by forcing energy (travelling photons) pursuing electrons and high energy photons (in high density) entering to solution. Gold atoms dissociated from the precursor under dissipating heat energy into the solution supplied under propagating photons characteristic current through immersed graphite rod (known in anode). Placing packets of nano shape energy of tuned pulse protocol over compact monolayer assembly comprising transition state atoms develop tiny-sized particles of formed shape. On separation of joint tiny particles into two equilateral triangular-shaped tiny particles, exerting forces of surface format elongate atoms of one-dimensional arrays converting them into structures of smooth elements. Due to immersing level of force, such tiny-shaped particles pack from different zones at centre of light glow where they assembled structures of smooth elements for developing mono-layers of different shapes of particles. Developing one-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from nearly rearward zones of reflection of north-south poles, whereas, developing multi-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from the east-west poles and near regions. Depending on the number of assembled structures of smooth elements at point of nucleation, packing of tiny-shaped particles from different zones develop different shapes of the anisotropic particles. At fixed precursor concentration, increasing the process time results into develop particles of low aspect ratio. Under tuned parameters, developing mechanisms of particles exhibiting unprecedented features are discussed.

Two meters is the ratio of the distance between two points according to the standard 1-meter ruler saved somewhere in France, and this comparative ratio is really equal to dimensionless number 2. We can easily repeat such comparative ratios for kilograms and any other quantities that modern physics believes they carry units. When we think about it, all physical quantities are dimensionless comparative ratios referred to standard units saved somewhere in France (never mind more complicated, derived units, they still depend on the particular items saved in France). Once this important fact is established for dimensional units, we realize how we should deal with dimensionless constants in physics: we need to determine one such constant by experiment, and then all other related dimensionless constants fall in place by simple ratios, just as has been done for dimensional units over many years in the past. For the forces of nature, we advocate the fine-structure constant as the dimensionless quantity that will serve as the baseline for other dimensionless constants representing the coupling of forces. Then, we can extend gravity in the atomic world and quantum physics into large-scale cosmology, both quite flawlessly.

Core-shell particles are heterogenous micro- or nanoparticles with solid, liquid or gas core encapsulated by a protective solid shell. The unique composition of core and shell materials imparts smart properties to the particles. Core-shell particles are gaining increasing attention as tuneable and versatile carriers for pharmaceutical and biomedical applications including targeted drug delivery, controlled drug release, and biosensing. This review first provides an overview of fabrication methods for core-shell particles, followed by a brief discussion on their application and a detailed analysis on manipulation including assembly, sorting, and triggered release. We compile current methodologies employed for manipulation of core-shell particles and demonstrate how existing methods of assembly and sorting micro/nanospheres can be adopted or modified for core-shell particles. Various triggered release approaches for diagnostics and drug delivery are also discussed in detail.

A systematic investigation of the dynamic clustering behavior of active particles under confinement, including the effects of both particle density and active driving force is presented based on a hybrid coarse-grained molecular dynamics simulation. First, a series of scaling laws were derived with power relationships for the dynamic clustering time as a function of both particle density and active driving force. Notably, the average number of clusters N ̅ assembled from active particles in the simulation system exhibits a scaling relationship with clustering time t described by N ̅∝t^(-m). Simultaneously, the scaling behavior of the average cluster size S ̅ is characterized by S ̅∝t^m. Our findings reveals the presence of up to four distinct dynamic regions concerning clustering over time, with transitions contingent upon the particle density within the system. Furthermore, as the active driving force increases, the aggregation behavior also accelerates, while an increase in density of active particles induce alterations in the dynamic procession of the system.

Affine quantization is a relatively new procedure, and it can solve many new problems. This essay reviews this new, and novel, procedure for particle problems, as well as those of fields and gravity. New quantization tools, which are extremely close to, and even constructed from, the tools of canonical quantization, are able to fully solve selected problems that using the standard canonical quantization would fail. In particular, improvements can even be found with an affine quantization of fields, as well as gravity.

Starting from the SU(2) group of weak interactions in the presence of Electric Charge Swap (ECS) symmetry, we show that ordinary and non-regular (ECS) leptons are related by the ECS rotational group SO(3). We find that many Standard Model (SM) algebras depend on the sin of the angle θs of the ECS rotational group SO (3). We call these ECSM algebras. Furthermore, the break of the gauge symmetry of the SM groupoid gives the massive ECS particle. We find that the ECS particle masses are related with the SM particle masses by sinθs . We also investigate the finite subgroups of the ECS Möbius transformations. We find that sinθs could be derived from the ECS dihedral group DF, which refers to the symmetry of the fermionic polygon (F-gon). The average value of the anchor of the SM algebroid depends on the fermionic Catalan numbers (CF). Finally, we find that the ECS physics at loop level differs the SM physics. The ECSM mass is suppressed by the CF numbers. For 24 fermions, the calculated one-loop radiative correction to the bare Higgs mass µ is 125GeV—a value very close to the experimental one.

This work describes and interprets the presence of heavy minerals in the western Portuguese continental margin using a set of 78 bottom samples collected from 3 distinct areas of this margin: Porto, Aveiro and Nazaré canyon head areas. The main transparent heavy mineral suite (minerals with frequencies >10%), is composed by amphiboles (hornblende), mica (biotite), andalusite, tourmaline and garnet. A secondary suite (minerals with frequencies between 1 and 10%), is composed by pyroxene (enstatite, diopside and augite), staurolite, zircon and apatite. With very low frequency representing less than 1% we found rutile, olivine, kyanite, monazite, epidote, sphene, anatase, sillimanite and brookite. The main primary sources (igneous and metamorphic rocks) explain the presence of these minerals. However, the application of the principal component analysis, with a previous application of the centered log ratio transformation of the heavy mineral data, also stresses for the importance of the grain sorting as a process in controlling the heavy mineral occurrence. The importance of this process is mostly sustained by the distribution pattern of mica and of the most flattened amphibole grains in a way that these particles tend to have a hydraulic affinity to finer grained sediments.

Filamentous manganese (Mn) oxide particles, which occur in the suboxic zone of stratified waterbodies, are important drivers of diverse elemental cycles. Although these particles are considered to be bacteriogenic, the environmental factor responsible for their formation has not been identified. Based on this study of laboratory cultures of a model Mn(II)-oxidizing bacterium, the supply of algal extracellular polymeric substances (EPS) was shown to stimulate Mn(II) oxidation and thus the production of filamentous Mn oxide particles. This observation was consistent with results obtained for naturally occurring particles collected from a near-bottom layer (depth of ~90 m) in the northern basin of Lake Biwa, Japan, that is, most Mn particles resembling delta-MnO2 were associated with an EPS-like gelatinous matrix, which contained dead algal cells and was lectin-stainable. In the lake water column, EPS produced by photosynthesis sank to the bottom layer. The analysis of the quality of water samples, which have been collected from the study site for 18 years, reveals that the annual average total phytoplankton biovolume in the surface layer correlates with the density of filamentous Mn particles in the near-bottom layer. Among different phytoplankton species, green algae appeared to be the key species. The results of this study suggest that algal EPS production induces the formation of filamentous Mn oxide particles in the near-bottom layer of the northern basin of Lake Biwa.

Low-cost monitors make it possible now for the first time to collect long-term (months to years) measurements of potential indoor exposure to fine particles. Indoor exposure is due to two sources: particles infiltrating from outdoors and those generated by indoor activities. Calculating the relative contribution of each source requires identifying an infiltration factor. We develop a method of identifying periods when the infiltration factor is not constant, and searching for periods when it is relatively constant. From an initial regression of indoor on outdoor particle concentrations, a Forbidden Zone can be defined with an upper boundary below which no observations should appear. If many observations appear in the Forbidden Zone, they falsify the assumption of a single constant infiltration factor. This is a useful quality assurance feature, since investigators may then search for subsets of the data in which few observations appear in the Forbidden Zone. The usefulness of this approach is illustrated using examples drawn from the PurpleAir network of optical particle monitors. An improved algorithm is applied with reduced bias, improved precision, and a lower limit of detection than either of the two proprietary algorithms offered by the manufacturer of the sensors used in PurpleAir monitors.

Flotation of small particles is one of the global challenges facing the mineral raw materials processing industry. Large amounts of non-ferrous and rare metals are lost in the flotation tailings in the form of mineral particles below 15 µm in size as a result of the low effectiveness of their capture by coarse bubbles generated in conventional flotation machines. The method of combined microflotation, which is being developed in recent years, uses not only coarse but also microbubbles (MB) produced in the stand-alone generator of air-in-water microdispersion, which serves as the flotation carriers. Depending on the dose of MB, the effect of their application may be both positive, but also negative. The theoretical analysis of various mechanisms of particle transfer onto the surface of coarse bubbles and further into the froth layer allowed to obtain the formula for the optimal MB dose f=2dddpρp, where dd is MB size; dp and ρp respectively are the size and the density of particles. Experiments performed on the copper ore flotation tailings at the Atalaya Mining (Spain) and Chaarat Kapan (Armenia) concentrators showed that, besides the optimal MB dose in the range of 1-3 ml/g, there is another optimal MB dose in the range of 10-20 ml/g, where the copper recovery increases by several percent compared to the reference test (f= 0). In the area between the optimal MB doses, the deep minimum in copper recovery is observed, which value is by several percent lower compared to the value in the reference test.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

Recent researches indicated that metal nanoparticles which have the unique optical properties can be used to enhance the spectral response of the photovoltaic modules. Since most of the nanoparticles have enhancement effects in a specific wavelength range, improving the spectral response of the photovoltaic modules in a broadband range is crucial for their applications in imaging, energy harvesting, and optical communication. In this study, flower-like silver particles are applied to achieve the enhancement effects in a broadband range. The optical absorption of photovoltaic modules is improved in a broad wavelength range of 400~2000 nm by immobilizing flower-like silver particles onto an amorphous Si p-i-n structure, and the peak responsivity of the spectral response is enhanced by about 10 times. Theoretical investigation further elaborates that the enhancement originates from the near-field effects of silver particles due to the interaction of different parts of the flower-like silver particles. Through these studies, we demonstrate that, utilizing the subwavelength silver particles with roughness surface can achieve the spectral response of the photovoltaic modules enhanced in broadband range, which can improve the utilization efficiency of optical energy for the applications of sensing, imaging, optical communication, and energy harvesting.

Major progress in the field of regenerative medicine are expected from the design of artificial scaffolds that mimic both the structural and functional properties of the ECM. The bionanocomposites approach is particularly well fitted to meet this challenge as it can combine ECM-based matrices and colloidal carriers of biological cues that regulate cell behavior. Here we have prepared bionanocomposites under high magnetic field from Tilapia fish scale collagen and multifunctional silica nanoparticles (SiNPs). We show that scaffolding cues (collagen), multiple display of signaling peptides (SiNPs) and control over the global structuration (magnetic field) can be combined into a unique bionanocomposite for the engineering of biomaterials with improved cell performances.

I demonstrate that the macrocosmic gravitational interaction between two masses and the microcosmic electrostatic interaction between two charges unify in simple concepts and mathematical laws when electric charge and ordinary mass are interpreted in reciprocal terms. No previous research has ever attempted to unify charge and mass. The difficulty has been lack of an intelligible definition of charge. A three-point paradigm shift solves the problem, giving convincing evidence – for the first time – that positron and negatron are the ultimate elementary particles. That is, matter is pure positive and negative grains of electricity. Paradigm shift #1: Electron is a moving charge; a charge is static electron – ‘one entity two identities’. This implies that ordinary matter contains equal numbers of positive and negative electrons – observed in motion as ‘electrons’ and at rest as ‘charges’. In motion, a positron-negatron pair obeys the laws of electrodynamics and annihilates; at rest, the pair obeys the laws of electrostatics and neutralizes. Paradigm shift #2: Electron mass and electrostatic field are either positive or negative. Opposite masses and fields, rather than indefinable ‘charge’, make opposite electrons physically different. Paradigm shift #3: Electric charge and ordinary mass interconvert. Positive charge (e⁺) and negative charge (e^-) neutralize to neutral charge (2e⁰), which is nature’s quantum of ordinary mass. Conversely, a quantum of ordinary mass splits to opposite charges e.g. in frictional electrification. The insights systematize the search, identification and classification of ‘elementary particles’, ending decades of confusion in the ‘elementary particle zoo’. They identify a new, stable subatomic particle – a third nucleon.

Immobilizing particles on beads, fibers or filaments, when only one side is exposed to the reaction medium and therefore can be selectively functionalized, is a scalable and easy to control strategy for the fabrication of amphiphilic Janus particles. Here we describe a new, robust method for the fabrication of amphiphilic Janus particles based on immobilization of polymethylsilsesquioxane (PMSQ) particles on polycarbonate (PC), a high impact-resistance polymer with superior mechanical properties. The immobilization of the particles on the PC microspores is preformed via inverse solvent displacement method. PMSQ particles are added to a PC solution in tetrahydrofuran (THF), a good solvent for PC. The solution is then precipitated by the introduction of aqueous surfactant solution (anti solvent for PC) under an ultrasonic field. It is important to note that THF and water are miscible and do not form emulsion. During precipitation, PMSQ particles are assembled onto the surface of the PC spherical precipitates/microspheres. The exposed hemispheres of the PMSQ particles are then selectively silanized by (3-Aminopropyl)triethoxysilane (APTES) to introduce amine groups on their surface. To increase the polarity of the functionalized hemispheres, the amine groups are further modified to introduce carboxyl groups. SEM characterization confirms the fine embedment of PMSQ particles onto the PC microspheres. Covalent attachment of silica nanoparticles (NPs) to the functionalized hemispheres of the resulting particles along with fluorescent confocal microscopy conclusively proof the successful fabrication of amphiphilic Janus particles. The immobilization of particles onto highly rigid polymeric microspheres such as PC may pave the way to the development of a robust fabrication procedure with high resistance to temperature fluctuations and harsh mixing conditions that can arise during preparation. This method can be implemented toward a large variety of other synthetic commercial polymers such as polyamide, polyether sulfones, Polyether ether ketone or similar.

Walking School Buses (WSBs) provide a safe alternative to being driven to school. Children benefit from the contribution the exercise provides towards their daily exercise target, it gives children practical experience with respect to road safety and helps to relieve traffic congestion around the entrance to their school. Walking routes are designed largely based in road safety considerations, catchment need and the availability of parent support. However, little attention is given to the air pollution exposure experienced by children during their journey to school, despite the commuting microenvironment being an important contributor to a child’s daily air pollution exposure. This study aims to quantify the air pollution exposure experienced by children walking to school and those being driven by car. A school was chosen in Bradford, UK. Three adult participants carried out the journey to and from school each carrying a P-Trak ultrafine particle (UFP) count monitor. One participant travelled the journey to school by car while the other two walked, each on opposite sides of the road for the majority of the journey. Data collection was carried out over a period of two weeks, for a total of five journeys to school in the morning and five on the way home at the end of the school day. Results of the study suggest that car commuters experience lower levels of air pollution dose due to lower exposures and reduced commute times. The largest reductions in exposure for pedestrians can be achieved by avoiding close proximity to traffic queuing up to intersections, and, where possible, walking on the side of the road opposite the traffic, especially during the morning commuting period. Major intersections should also be avoided as they were associated with peak exposures. Steps to ensure that the phasing of lights is optimized to minimize pedestrian waiting time would also help reduce exposures. If possible, busy roads should be avoided altogether. By the careful design of WSB routes, taking into account air pollution, children will be able to experience the benefits that walking to school brings while minimizing their air pollution exposure during their commute to and from school.

In this study, the problem of overcoming the infinite energy barrier separating the bradyonic and tachyonic realms is investigated. Making use of the Majorana equation for particles with arbitrary spin and the Heisenberg uncertainty principle, it is proved that, under certain conditions of spatial confinement, quantum fluctuations allow particles with very small mass and velocity close to the speed of light to pass in the tachyonic realm, avoiding the problem of the infinite barrier (bradyon–tachyon tunnelling). This theoretical approach allows an avoidance of the difficulties encountered in quantum field theory when it is extended to particles with imaginary rest mass.

If we assume that: a. The four fundamental forces of nature are independent waves without rest masses, and their speeds are constant in a vacuum, just like light. b. Light or electromagnetic waves and gravity are comparable in structures. Weak and strong interactions are similar in structures. c. Light and weak interaction have the same speed c_L with spin number +1 or –1. d. Gravity and strong interaction have the same speed c_G without spin. e. The primary particles, namely electrons, electron neutrinos, and dark neutrinos in this paper, are made by the above four waves. We can find and describe some fundamental characteristics of the primary particles (e.g., their sizes, energies, and interactions) and introduce new attractive results from them (e.g., the source of the Pauli exclusion principle, the solution to the Einstein-Podolsky-Rosen paradox, and c_G slightly faster than c_L).

The fluid seepage in local-saturated zone of subgrade promotes the migration of fine particles in the filler, resulting in the change of pore structure and morphology of the filler and the deformation of solid skeleton, which affects the fluid seepage characteristics. Repeatedly, the muddy interlayer, mud pumping and other diseases are finally formed. Based on the theory of two-phase seepage, the theory of porous media seepage, and the principle of effective stress in porous media, a two-phase fluid-solid coupling mathematical model in local-saturated zone of subgrade considering the effect of fine particles migration is established. The mathematical model is numerically calculated with the software COMSOL Multiphysics○R, the two-phase seepage characteristics and the deformation characteristics of the solid skeleton in local-saturated zone of the subgrade are studied. The research results show that due to the continuous erosion and migration of fine particles in local-saturated zone of the subgrade, the volume fraction of fine particles first increases then decreases and finally becomes stable with the increase of time. And the volume fraction of fine particles for the upper part of the subgrade is larger than that for the lower part of the subgrade. The porosity, the velocity of fluid, the velocity of fine particles, and the permeability show a trend of increasing first and then stabilizing with time; the pore water pressure has no significant changes with time. The vertical displacement increase first and then decrease slightly with the increase of time, and finally tend to be stable. For a filler with a larger initial volume fraction of fine particles, the maximum value of the volume fraction of fine particles caused by fluid seepage is larger, and the time required to reach the maximum value is shorter. It can be concluded that in actual engineering, the volume fraction of fine particles in the subgrade filler should be minimized on the premise that the filler gradation meets the requirements of the specification.

Despite the recognized potential of nanoparticles, only a few formulations have progressed to clinical trials, and an even smaller number have been approved by the regulatory authorities and marketed. Virus-like particles (VLPs) have emerged as promising alternatives to most explored nanoparticles because of the absence of viral genetic material, their incapacity to replicate, mimicry of viral structure, and tropism conservation. Furthermore, VLPs can be surface functionalized with small molecules to improve circulation half-life and target specificity. Through the functionalization and coating of VLPs, it is possible to optimize the response properties to a given stimulus, such as heat, pH, an alternating magnetic field, or even enzymes. Surface functionalization can also modulate other properties, such as biocompatibility, stability, and specificity, deeming VLPs as potential vaccine candidates or delivery systems. In this review, we address the different types of functionalization of VLPs, their importance, and their consequent biomedical applications.

This article begins with exploring fundamental limits in the universe. It examines key principles, such as the uniformity of physical laws and Energy conservation, that lead to maximum speed, locality, and maximum density. These universal limits govern physical phenomena, leading to very interesting results.I demonstrate that quarks and leptons comprise smaller entities named "Quantum Black Holes." These Quantum black holes are relativistically rotating miniature charged black holes consisting of a single core at the highest possible density. Quantum black holes are the only structures small enough in space-time capable of keeping all charges quantized (including gravitational charges.)By the end of the article, I prove that Quantum black holes explain the deficiencies of SM. They facilitate explanations of quantized gravity, the nature of Luminous and dark Matter, establishing the Mass, size, and (quantized) charges quantities of elementary particles, the nature of neutrino oscillations, and more. Elementary particles release their Energy outward, altering the curvature of nearby space-time and providing new insights into the nature of space-time curvature change. With this understanding, we can characterize movements and processes in local space-time using five sets of equations simultaneously: four representing the four charge types and one representing Dark Matter.

Acoustic focusing of particle flow in microfluidics has been shown to be an efficient tool for particle separation for various chemical and biomedical applications. The mechanism behind the method is the selective effect of the acoustic radiation force on distinct particles. In this way, they can be selectively focused and separated. The technique can also be applied under stationary conditions, i.e., in the absence of fluid flows. In this study, the manipulation of self-propelled particles, such as Janus particles, in an acoustofluidic setup is investigated. In experiments with self-propelled Janus particles and passive beads, we explore the interplay between self-propulsion and the acoustic radiation force. Our results demonstrate unusual and potentially useful effects such as selective trapping, escape and assisted escape in binary mixtures of active and passive particles. We also analyze various aspects related to the behavior of Janus particles in acoustic traps in the presence and absence of flows.

The primary sources of particulate matter are linked to human activity. Certain particulate emissions, particularly those of a finer nature, can significantly impact human health, making them one of the most concerning pollutants. Ultrafine particles (UFP), which have a diameter of less than 100 nm, are of particular concern due to their impact on human health and the difficulty in controlling them. The concentration of ultrafine particles (UFP) in the workplace is a growing concern and is classified as an emerging risk. Workers may be exposed to UFP through inhalation, skin absorption, ingestion, or a combination of these routes. This study aims to determine the levels of UFP exposure among workers in environments with varying direct particle emission patterns. Measurements were conducted to compare the results with the levels recommended by the WHO. The study monitored industrial workplaces with direct particulate matter emissions, such as a carpentry and a bakery, as well as social sector sites without or almost without direct particle emissions, such as a school and a health clinic. One conclusion drawn from this study is that all tasks and occupations are susceptible to high levels of UFP, exceeding WHO recommended values in virtually all monitored environments. Therefore, monitoring and controlling UFP is crucial. Further in-depth studies on this subject are also necessary..

Two novel members of the subfamily Betarhabdovirinae, family Rhabdoviridae, were identified in Brazil. Overall, their genomes have the typical organization 3’-N-P-P3-M-G-L-5’ observed in mono-segmented plant-infecting rhabdoviruses. In aristolochia-associated cytorhabdovirus (AaCV), found in the liana aristolochia (Aristolochia gibertii Hook), an additional short orphan ORF encoding a transmembrane helix was detected between P3 and M. AaCV genome and deduced encoded proteins share the highest identity values, consistently < 60%, with their counterparts of yerba mate chlorosis-associated virus (Cytorhabdovirus flaviyerbamate). The second virus, false jalap virus (FaJV), was detected in the herbaceous plant false jalap (Mirabilis jalapa L.) and represents together with tomato betanucleorhabdovirus 2, originally found in tomato plants in Slovenia, a tentative new species of the genus Betanucleorhabdovirus. FaJV particles accumulate in the peri-nuclear space, and electron-lucent viroplasms were observed in the nuclei of the infected cells. Notably, distinct from typical rhabdoviruses, most virions of AaCV were observed to be non-enclosed within membrane-bounded cavities. Instead, they were frequently seen in close association with surfaces of mitochondria or peroxisomes. Unlike FaJV, AaCV was successfully graft-transmitted to healthy plants of three species of the genus Aristolochia, while mechanical and seed transmission proved unsuccessful for both viruses. Data suggest that these viruses belong to two new tentative species within the subfamily Betarhabdovirinae.

The pressing process and density profile of particleboards produced with addition of waste wood containing phenol-formaldehyde (PF) resin was presented. The particles were melamine-urea-phenol-formaldehyde (MUPF) resinated. Recovered particles were obtained from post-industrial waste plywood. The press closing time recorded during the pressing of mats containing only recovered particles in the core layer (100%), at a unit pressure of 3 MPa, in which the face layer rate was 50%, resin load for face and core layer was 12% and 10% was shorter by 29% than for the industrial particle mats. Regardless of the level of variability of independent factors the overheating time of mats to a temperature of 100 °C, containing recovered particles was 10% - 20% shorter than the time of overheating mats with industrial particles. The greatest impact (52%) on maximum density of the face layer of particleboards was demonstrated by the content of the recovered particles and the resin load (32%). The maximum density area of the face layer was located closer to the surface in particleboards produced with a higher (80%, 100%) content of the recovered particles, a higher (i.e. 12% and 10%, respectively, for face and core layer) resin load, a lower (35%) face layer rate and a higher (3 MPa ) unit pressure.

In this study, we reported that novel single-chain fusion-proteins linked thromboxane A2 (TXA2) receptor (TP) to a selected G-protein α-subunit q (SC-TP-Gαq), or s (SC-TP-Gαs) could be stably expressed in megakaryocytes (MK). We tested the MK-released platelet-linked particles (PLPs) to be used as a vehicle to deliver the over-expressed SC-TP-Gαq), or s (SC-TP-Gαs) to regulate human platelet function. To understand how the single-chain TP-Gα fusion proteins could regulate opposite platelet activities by an identical ligand TXA2, we used dual-binding domains linked to different signaling pathways within a single polypeptide chain using a 3D structural model. The immature MKs were cultured and transfected with cDNAs constructed from structural models of the individual SC-TP-Gαq and SC-TP-Gαs, respectively. After transient expression was identified, the immature MKs stably expressing SC-TP-Gαq or SC-TP-Gαs (stable cell lines) were selected. The stable cell lines were induced into mature MKs which released PLPs. Western blot analysis confirmed that the released PLPs were carrying the recombinant SC-TP-Gαq or SC-TP-Gαs. Flow cytometry analysis showed the PLPs carrying SC-TP-Gαq were able to perform the activity by promoting platelet aggregation. In contrast, PLPs carrying SC-TP-Gαs reversed Gq to Gs signaling to inhibit platelet aggregation. This is the first time demonstrating that SC-TP-Gαq and SC-TP-Gαs were successfully overexpressed in MK cells and released as PLPs with proper folding. This bio-engineering led to the formation of two sets of biologically active PLP forms, which mediate calcium and cAMP signaling, respectively. As a result, these PLPs are able to bind to identical endogenous TXA2 with opposite activities, inhibiting and promoting platelet aggregation as required for therapeutic process.The results also demonstrated the nucleus-free PLPs could be used to deliver recombinant membrane-bound GPCRs to regulate cellular activity in general.

Hemoglobin based oxygen carriers (HBOC) as blood substitutes are one of the great hopes of modern transfusion and emergency medicine. After the major safety-relevant challenges of the last decades seem to be largely overcome, current developments have in common that they are affected by degradation and excretion at an early stage in test organisms. Several possible mechanisms that may be responsible for this are discussed in the literature. One of them is CD163, the receptor of the complex of haptoglobin (Hp) and hemoglobin (Hb). The receptor has been shown in various studies to have an affinity for Hb in the absence of Hp. Thus, it seems reasonable that CD163 could possibly also bind Hb within HBOC and cause phagocytosis of the particles. In this work we investigated the role of CD163 for the uptake of our HbMP (hemoglobin sub-micron particles) in monocytes and additionally screened for alternative ways of particle recognition by monocytes. In our experiments, blockade of CD163 by specific monoclonal antibody proved to partly inhibit HbMP-uptake by monocytes. It appears however, that several other phagocytosis pathways for HbMP might exist, independent of CD163 and also Hb.

Seasonal variations in atmospheric ultrafine particulate matter (PM0.1) were monitored in Bangkok, Thailand, from 2016 to 2017. PM0.1 bound organic carbon (OC), and elemental carbon (EC) were collected by a cascade air sampler that can collect PM0.1 and estimated by a thermal-optical carbon analyzer following the IMPROVE-TOR protocol. The annual average PM0.1 in Bangkok was 14.5 ± 4.7 µg/m3, higher than in large Asian cities like Shanghai and Hanoi. Biomass burning from neighboring areas was shown to increase the particle concentration. Apparent risings in carbon species as OC, EC, and OC/EC ratios in the wet and dry seasons were observed, and Char-EC/Soot-EC displayed that the PM0.1 in the Bangkok atmosphere was influenced mainly by the vehicle exhaust, even though the influence of biomass burning was more sensitive during the dry season. The effective carbon ratio (ECR) displays that carbonaceous aerosol is light-absorbing; the dry season increase contributed to climate and air quality. The finding of this work is of great importance to air pollutants control policies in urban areas.

Prior studies have focused on the overall behavior of randomly moving particle swarms. However, the characteristics of the stochastic-constrained particles that form ubiquitously within these swarms remain oblivious. This study demonstrates a generalized diffusion equation for stochastic-constrained particles that considers the velocity and location aggregation effects observed from their parent particle swarm (i.e., a completely random particle swarm). This equation can be approximated as the form of Schr\"odinger equation in the microcosmic case (low relative density) and describe the dynamics of the total mass distribution in the macrocosmic case (high relative density). The predicted density distribution of the particle swarm in the stable aggregation state is consistent with the total mass distribution of massive, relaxed galaxy clusters (at least in the range of r < r_s), preventing cuspy problems in the empirical Navarro-Frenk-White (NFW) profile. This study opens a window to observe the dynamics of stochastic-constrained particles from a third perspective, from which the aggregation effect of particles without gravitation can be saw.

The acquisition of adverbs in French as L2 (FSL) by learners with different L1s, at various levels of proficiency, has been extensively studied within various SLA projects (ESF, Interfra etc.). In the generativist tradition, it has been noted that “high category adverbs” such as those related to Mood-evaluative, Mood-epistemic and Tense are present early in FSL data. In the functionalist school, the early presence of time adverbs and scope particles in learner varieties has been analysed in relation with the informational and syntactic structures observed in these varieties and in terms of their contribution to temporal reference and other semantic domains in discourse.

In this article we first write a brief review of supersymmetric quantum mechanics and then we discuss the equivalence of two co-existing formalisms viz. tensor product formalism and partner hamiltonian formalism for 1-D SUSY Harmonic oscillator. Finally, we present a Mathematica code with which one can calculate the eigenstates of any 1-D SUSY partner Hamiltonian along with two illustrated examples of 1-D SUSY HO and 1-D SUSY infinite potential box.

Residential coal combustion is one of the most significant sources of carbonaceous aerosols in the Highveld region of South Africa, significantly affecting the local and regional climate. In this study, we investigated single coal-burning particles emitted when using different fire-ignition techniques (top-lit up-draft vs bottom-lit up-draft) and air ventilation rates (defined by the number of air holes above and below the fire grate) in selected informal braziers. Aerosol samples were collected on nucleopore filters at the Sustainable Energy Technology and Research Centre Laboratory, University of Johannesburg. Individual particles (~700) were investigated using a scanning electron microscope equipped with energy-dispersive X-ray spectroscopy (EDS). Two distinct forms of spherical organic particles (SOPs) were identified, one less oxidized than the other. The particles were further classified into "electronically" dark and bright. EDS analysis showed that 70% of the dark spherical organic particles had higher (~60%) relative oxygen content than in the bright SOPs. We quantified the morphology of spherical organic particles and classified them into four categories: ~50% are bare single particles; ~35% particles are aggregated and form diffusion accretion chains; 10% have inclusions, and 5% are deformed due to impaction on filter material during sampling. We conclude that there are two distinct kinds of coal burning spherical organic particles and that dark SOPs are less volatile than bright SOPs. We also show that these spherical organic particles are similar in nature and characteristics to tar balls observed in biomass combustion and that they have the potential to absorb sunlight thereby affecting the earth’s radiative budget and climate. This study provides insights into the mixing states, morphology, and possible formation mechanisms of these organic particles from residential coal combustion in informal stoves.

In order to achieve better knowledge of the thermal barrier coatings (TBCs) by supersonic atmospheric plasma spraying (SAPS) process, an experimental study was carried out to elaborate physicochemical properties of particles in-flight during the SAPS process. One type of commercially available agglomerated and sintered yttria-stabilized-zirconia (YSZ) powders were injected into the SAPS plasma jet and collected by shock chilling method. The YSZ particles in-flight physicochemical properties of the melting state, morphology, microstructure, particle size distribution, element composition changes and phase transformation during the SAPS process have been systematically analyzed. The melting state, morphology and microstructure of the collected particles were determined by scanning electron microscopy (SEM). The particle size distribution was measured by a laser particle size analyzer (LPSA). Element compositions were quantitatively analysed by an electron probe X-ray microanalyzer (EPMA). Additionally, the X-ray diffraction (XRD) method was used to analyse the phase transformation. The results showed that the original YSZ powders injected into the SAPS plasma jet were quickly heated and melted from the outer layer companied with breakup and collision-coalescence. The outer layer of the collected particles containing roughly hexagonal shaped grains exhibited a surface texture with high sphericity and the inside was dense with hollow structure. The median particle size was decreased from 45.65 μm to 42.04 μm. Besides, phase transformation took place and the content of zirconium (Zr) and yttrium (Y) element was decreased with the evaporation of ZrO2 and Y2O3.

Bio-separation of natural molecules as well as clinical compounds has been constantly developed in last decades. Several techniques are available but the majority of them presents drawbacks such us impossibility to be applied for industrial purposes. The main limitations for the scaling up are high costs and the fact that the devices work with microfluid dynamics. Nevertheless, magnetic bio-separation is considered the most prone to be used for large scale applications. Herein, we propose a simple magnetic separation method that is not based on microfluid dynamics, can work in a continuous- and high-flow rate and can be easily automated in order to be used for standard separation purposes. It is based on the use of an anisotropic flexible ferric magnetic strip, Teflon hoses and a pumping device. We show the modelling of the separation process along with an experimental test on iron oxide magnetic particles. The results showed that it is possible to remove, and separately collect, more than 92% of magnetic particles from a liquid solution of 100 ml in roughly 15 minutes.

A new approach to the measurement with elastic lidar of depolarization produced by atmospheric aerosols is presented. The system uses two different telescopes: one for depolarization measurements and another for total-power measurements. The system architecture and principle of operation are described. The first experimental results are also presented, corresponding to a collection of atmospheric conditions over the city of Barcelona.

This paper investigates the problem of a relativistic Dirac half-integer spin free particle tunneling through a rectangular quantum-mechanical barrier. If the energy difference between the barrier and the particle is positive, and the barrier width is large enough, there is proof that the tunneling may be superluminal. For first spinor components of particle and antiparticle states, the tunneling is always superluminal regardless the barrier width. Conversely, the second spinor components of particle and antiparticle states may be either subluminal or superluminal depending on the barrier width. These results derive from studying the tunneling time in terms of phase time. For the first spinor components of particle and antiparticle states, it is always negative while for the second spinor components of particle and antiparticle states, it is always positive, whatever the height and width of the barrier. In total, the tunneling time always remains positive for particle states while it becomes negative for antiparticle ones. Furthermore, the phase time tends to zero, increasing the potential barrier both for particle and antiparticle states. This agrees with the interpretation of quantum tunneling that the Heisenberg uncertainty principle provides. This study’s results are innovative with respect to those available in the literature. Moreover, they show that the superluminal behaviour of particles occurs in those processes with high-energy confinement.

The Standard Model is not a complete description of reality; it omits the existence of dark matter, dark energy, and an explanation as to why no CP violation has been observed. However, some of these phenomena could be explained through a new force mediated by a new boson. If such a boson were massless it would result in a power law potential and if massive the interaction would be Yukawa-like. A previous experiment employing a micro-mechanical oscillator and a spherical test mass interactions was successful in placing the best limits on a mass-mass Yukawa-like interaction, but the data was never analyzed in the context of a power law. Here that data is analyzed considering a power law for powers n = 1-5 where n is the number of boson exchanges. The results show that the limits obtained through power law analysis of this data are not better than the currently accepted limits. A discussion of an experiment design capable of producing better limits on power law extensions to the Standard Model is presented, and suggests micro mechanical oscillators based experiment remains capable of improving the limits by at least one order of magnitude.

Low-cost monitors have made possible for the first time measurements of long-term (months to years) potential indoor exposures to fine particles. Indoor and outdoor measurements made over nearly 5 years (2017-2021) by the largest network of low-cost monitors in the United States (PurpleAir) are compared to the prevalence of adult smokers in 1650 Zip codes within the three West Coast states of California, Oregon, and Washington. The results show that mean indoor exposures above the 75th percentile of adult smoking prevalence are more than 50% higher than those below the 25th percentile. Mean outdoor concentrations are also elevated, but by a smaller amount (20%). Both comparisons are significant at the p&lt;0.001 level. The elevation of the PM2.5 concentrations with increasing smoking prevalence is evidence of environmental disparities in income, education, and other socioeconomic indices..

The flow field around a straight chain of multiple slip spherical particles rotating steadily in an incompressible Newtonian fluid about their line of centers is analyzed at low Reynolds numbers. The particles may vary in radius, slip coefficient, and angular velocity, and they are permitted to be unevenly spaced. Through the use of a boundary collocation method, the Stokes equation governing the fluid flow is solved semi-analytically. The interaction effects among the particles are found to be noteworthy under appropriate conditions. For the rotation of two spheres, our collocation results for their hydrodynamic torques are in good agreement with the analytical asymptotic solution in the literature obtained by using a method of twin multipole expansions. For the rotation of three spheres, the particle interaction effect indicates that the existence of the third particle can influence the torques exerted on the other two particles noticeably. The interaction effect is stronger on the smaller or less slippery particles than on the larger or more slippery ones. Torque results for the rotation of chains of many particles visibly show the shielding effect among the particles.

Detection of virus in sample is an actual problem in biotechnology, virology, medicine using biosensor. History of problem dates back to middle of last century and is associated with development of an ion-sensitive solid-state device for neurophysiological measurements. Aim of work is theoretical investigation process of detection antibody+antigen (AB+AG) complexes using SOI-FET biosensor. On example of crystal with ten biosensors, estimates of probability detection AB+AG complexes influenza virus are made. In detection process, following four results are possible: – target complex is present in test sample, and it was correctly detected; – target complex is present in sample, but it was not detected; – target complex is absent in sample, but background particles are mistakenly detected as target complex; – target complex is absent in sample, background particles present in sample and are correctly detected as noise.

Up to now, many studies have been performed on particle radiations before or during earthquakes (EQs). In our previous study, with the help of piezoelectricity relationships and the elastic energy formula, the MCNPX simulation code was applied to find the amount of created atomic/ nuclear particles, the dominant interactions; and the energy of the particles for various sizes of quartz and granite blocks. In this study, using the MCNPX simulation code, we have estimated the flux of the particles (created from under-stressed granitic rocks) at different distances from the EQ hypocenter inside the fractures, filled with air, water, and CO2. It was found that inside a water-filled fracture, the particles do not show the flux far from the EQ hypocenter, but inside the gases like air and CO2 with the normal condition density, different types of particles can have a flux far from the source (more than a kilometer) and they might reach themselves to the surface in the case that the EQ hypocenter is very shallow (0- 5 km). However, for deep EQs, it seems that the most detected nuclear particles on the surface should pass via the vacuum-filled fractures and reach themselves to the surface. Moreover, it was concluded that the more density of the fracture’s filling fluid, the less distance that the particles can have a flux.

Natural systems of units $\{U_i\}$ need to be overhauled to include the dimensionless coupling constants $\{\upalpha_{U_i}\}$ of the natural forces. Otherwise, they cannot quantify all forces in a unified manner. Thus, each force must furnish a system with at least one dimensional and one dimensionless constant. We revisit three natural systems of units (atomic, cosmological, and Planck). The Planck system is easier to rectify, and we do so in this work. The atomic system discounts $\{ G, \upalpha_G \}$, thus it cannot account for gravitation. The cosmological system discounts $\{ \slashed{h}, \upalpha_\slashed{h} \}$, thus it cannot account for quantum physics. Here, the symbols have their usual meanings; in particular, $\upalpha_G$ is the gravitational coupling constant and $\upalpha_\slashed{h}$ is the fine-structure constant. The speed of light $c$ and the impedance of free space $Z_0$ are resistive properties of the vacuum, thus they must be present in all systems of units. The upgraded Planck system $${\rm UPS} \,:=\,\{ c, Z_0, G, \upalpha_G, \slashed{h}, \upalpha_\slashed{h}, \,\dots\,\!\},$$ describes all physical scales in the universe---it is nature's system of units. As such, it reveals a number of properties, most of which have been encountered previously in seemingly disjoint parts of physics, and some of which have been designated as mere coincidences. Based on the UPS results, that relate (sub)atomic scales to the Planck scale and the fine-structure constant to the Higgs field, we can state with confidence that no observed/measured physical properties are coincidental in this universe.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Little is understood about the impact of nebulisation on the viability of SARS-CoV-2. In this study, a range of nebulisers with differing methods of aerosol generation were evaluated to determine SARS-CoV-2 viability following aerosolisation. The aerosol particle size distribution was assessed using an aerosol particle sizer (APS) and SARS-CoV-2 viability was determined after collection into liquid media using All-Glass Impingers (AGI). Viable particles of SARS-CoV-2 were further characterised using the Collison 6-jet nebuliser in conjunction with novel sample techniques in an Andersen size-fractioning sampler to predict lung deposition profiles. Results demonstrate that all the tested nebulisers can generate stable, polydisperse aerosols (Geometric standard deviation (GSD) circa 1.8) in the respirable range (1.2 to 2.2µm). Viable fractions (PFU/particle, the virus viability as a function of total particles produced) were circa 5x10^-3 and were not significantly affected by relative humidity. The novel Andersen sample collection methods successfully captured viable virus particles across all sizes; with most particle sizes below 3.3µm. MMADs (Mass Median Aerodynamic Diameters) were calculated from linear regression of log10-log10 transformed cumulative PFU data, and calculated MMADs accorded well with APS measurements and did not differ across collection method types. This data will be vital in informing animal aerosol challenge models, and infection prevention and control policies.

Complex colloidal fluids, depending on particulates’ shapes and packing fractions, may have a wide range of shear thinning and thickening behaviors. A particular interesting way to transition between different types of such behavior is by infusing functional complex particles that can be manufactured using modern techicques such as 3D printing. In this paper, we display 2D molecular dynamics simulations of such fluids with infused star-shaped functional particles, with variable leg length and number of legs, as they are infused in a non-interacting, coarse-grained fluid. We vary the packing fraction (ϕ) of the system, and for each different system we apply shear with various strain rate that turns the fluid into a jammed state and rise the apparent viscosity of fluid. We demonstrate the dependence of viscosity with the particles’ packing fraction. We show the role of shape and design dependence of the functional particles towards the transition to a shear thickening fluid .

Is the extensive decline of insects partially due to an insect-specific feature of their functional organization that is disadvantageous for living in an industrialized environment? The unique way in which gases are supplied in insect tissues is such a special trait. It exposes cells directly to the gas phase, via tracheae that end in micro-tubes, the tracheoles, which have diameters in the same range as particles of ultra-fine dust transported by air of industrialized countries. Number and volume of these particles – calculated to be inhaled by honeybees, e.g., – are indicative to locally impede O2-uptake and CO2-release and thus to restrain physiological activities.

Biological gels (bio-gels) are hydrated polymer networks that serve diverse biological functions, which often lead to intentional or unintentional exposure to particulate matter. In this work, we derive a microscopically motivated framework that enables the investigation of penetration mechanisms into bio-gels. We distinguish between two types of mechanisms: spontaneous (unforced) penetration and forced penetration. Using experimental data available in literature, we exploit the proposed model to characterize and compare between the micro-structures of respiratory, intestinal, and cervicovaginal mucus and two types of biofilms. Next, we investigate the forced penetration process of spherical and ellipsoidal particles into a locally quadrilateral network. The proposed framework can be used to improve and complement the analysis of experimental findings in vitro, ex vivo, and in vivo. Additionally, the insights from this work pave the way towards enhanced designs of nano-medicines and allow to assess risk factors related to the nano-pollutants exposure.

Macrophages are cells involved in the primary response to debris derived from wear of implanted CoCr alloys. The biocompatibility of wear particles from a high carbon CoCr alloy produced under polarization in physiological hyaluronic acid (HA) solution was evaluated in J774A.1 mouse macrophages cultures. Polarization was applied to mimic the electrical interactions observed in living tissues. Wear tests were performed in a pin-on-disk tribometer integrating an electrochemical cell in phosphate buffer solution (PBS) and in PBS supplemented with 0.3% HA, physiological synovial fluid concentration, used as lubricant solution. Wear particles produced in 0.3% HA solution showed a higher biocompatibility in J774A.1 macrophages in comparison to those elicited by PBS. A considerable improvement in macrophages biocompatibility in the presence of 0.3 % of HA was further observed by the application of polarization at potentials having current densities typical of injured tissues suggesting that polarization produces an effect on the surface of the metallic material that leads to the production of wear particles that are macrophages biocompatible and less cytotoxic. The results showed the convenience to consider electric interactions together with other particles parameters, as are size and composition, to get a better understanding of the biological effects of the wear products.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Acute and chronic respiratory diseases impose a significant economic and health burden. Distal small airway assessment requires invasive procedures such as a bronchoscopy and bronchoalveolar lavage. The Particles in Exhaled Air (PExA) device provides a non-invasive means of assessing small airways; it captures distal airway particles sized around 0.5-7m and contains particles of respiratory tract lining fluid (RTLF) that originate during airway closure and opening. The PExA device can measure particle count and mass according to particle size. Subsequent capture of particles in a thin membrane enables application of various analytical methods to assess a broad range of biomolecules including phospholipids, proteins, inflammatory profile, and other metabolites to characterise inflammation and diseases processes such as asthma, chronic obstructive pulmonary disease, acute respiratory distress syndrome, lung cancer, and more recently acute infections such as COVID-19. PExA analysis provides a promising alternative to traditional investigative methods in the assessment, diagnosis, and management of respiratory conditions. By evaluating specific biomarkers in the RTLF associated with airway inflammation, PExA may offer a more accurate and comprehensive understanding of the molecular-level changes in the small airways of patients with acute and chronic lung diseases.

Zeta potential refers to the electrokinetic potential present in colloidal systems, exerting significant influence on the diverse properties of nano-drug delivery systems. The impact of dielectric constant on the zeta potential and charge inversion of highly charged colloidal particles, immersed in a variety of solvents spanning from polar, such as water, to nonpolar solvents, and in the presence of multivalent salts, was investigated through primitive model Monte Carlo (MC) simulations. Zeta potential ξ is decreased as decreasing the dielectric constant of the solvent, and upon further increase in the salinity and the valency of the salt. At elevated levels of salt, the colloidal particles become overcharged, in all solvents. As a result, their apparent charge becomes opposite in sign to the stoichiometric charge. This reversal of charge intensifies until reaching a saturation point with further increase in salinity, as a result, their apparent charge becomes opposite in sign to the stoichiometric charge. This reversal of charge intensifies until reaching a saturation point with further increase in salinity.

Respiratory viral infections, including influenza, respiratory syncytial virus (RSV), and, more recently, the coronavirus disease 2019 (COVID-19) pandemic, continue to pose significant global health threats. Conventional treatments for these infections often face challenges such as limited efficacy, the emergence of drug-resistant strains, and the requirement for frequent administration. In recent years, nanobodies have emerged as a promising class of therapeutic agents due to their unique properties, including small size, high stability, and specific binding capabilities. This mini-review article focuses on the application of nanobodies as spray and aerosol particles for the treatment of respiratory viral infections. Furthermore, we highlight the remarkable efficacy of nanobodies in preclinical and clinical studies against respiratory viruses, including their ability to neutralize viral particles, inhibit viral replication, and modulate the host immune response. We discuss the potential advantages of using nanobodies as inhalable formulations, including their improved delivery to the respiratory tract, enhanced stability in aerosol form, and reduced systemic side effects. Additionally, we explore the various strategies employed to engineer nanobodies for optimal aerosol delivery, such as conjugation to carrier particles or formulation as dry powders. We also examine the potential challenges and limitations associated with the development of nanobody-based aerosol therapies, including production scalability, cost-effectiveness, and regulatory considerations.

In this study, we investigate the behavior of randomly moving particles with a defined average energy, focusing on their biased motion around a specific point. These particles' velocity magnitudes follow a Maxwell distribution with a specific scale parameter. Our analysis derives the stochastic rotation rules for these particles and introduces the Ito equation conditions for biased stochastic rotation at a given curl value. We also consider the special relativistic-like effects in this context. The findings are validated through a representative example.

The concept of targeted drug delivery can be described in terms of the drug’s ability to mimic the other biological objects’ property to localize to target cells or tissues. For example, drug delivery systems based on red blood cells or mimicking some of their useful features, such as long circulation in stealth mode, have been known for decades. On the contrary, therapeutic strategies based on macrophages have gained very limited attention until recently. Here we review two biomimetic strategies associated with macrophages, that can be used to develop new therapeutic modalities: First, the mimicry of certain types of macrophages (i.e., the use of macrophages, including tumor-associated, or macrophage-like particles as a carrier for targeted delivery of therapeutic agents); and Second, the mimicry of ligands, naturally absorbed by macrophages (i.e., the use of therapeutic agents specifically targeted at macrophages). We discuss potential applications of biomimetic systems involving macrophages for the new advancements in treatment of infections, inflammatory diseases, and cancer.

Previous research via cell experiments has shown that ultrafine particles (UFPs, particles less than 100 nm) emitted from Three-Dimensional desktop printers (3D printers) had cytotoxicity. However, a few particles from different filaments and their cytotoxicity combinations have been tested. Here we quantify emissions of UFPs and use Air-Liquid Interface (ALI) from one commercially available filament extrusion desktop 3D printer utilizing three different filaments by controlled experiments. A549 cells were exposed at the ALI to UFPs generated by a working 3D printer for an average of 45 minutes and 90 minutes. Twenty-four hours after exposure, cells were analyzed for percent cytotoxicity grown on the 24-well ALI insert (LDH assay). UFP exposure resulted in decreased cell viability (significantly increased LDH levels). The result shows that Acrylonitrile butadiene styrene (ABS) has the most significant particle emission. ALI exposures enable in vitro testing of mixtures of particles such as UFP from a 3D printer. ABS is the only filament with a significant difference compared with the HEPA control in 90 minutes of exposure (p-value &lt;0.05). ABS and PETG we used during the experiment presented a significant difference compared with the HEPA control in 45 minutes of exposure.A screening analysis of potential exposure to these products in a typical environment suggests caution should be used when operating many printer and filament combinations in poorly ventilated spaces or without the aid of combined gas and particle filtration systems.

This paper presents the light scattering matrices of atmospheric aggregated hexagonal ice particles appearing in cirrus clouds. In this work aggregates consist of the same particles with different spatial orientation and number of these particles. Two types of particle shape were studied: (1) hexagonal column; (2) hexagonal plate. For both shapes we study compact and non-compact cases of arrangement of particles in aggregates. As a result, four sets of aggregates were made: (1) compact columns; (2) non-compact columns; (3) compact plates; (4) non-compact plates. Each set consists of eight aggregates with different number of particles from 2 to 9. For practical reason the bullet-rosette and the aggregate of hexagonal columns with different sizes was also calculated. The light scattering matrices were calculated for the case of arbitrary spatial orientation within the geometrical optics approximation for sets of compact and non-compact aggregates and within the physical optics approximation for two additional aggregates. It was found that light scattering matrix elements for aggregates are depend on arrangement of particles they are consisted.

PM_0.1 (particles diameter ≤ 0.1 µm), nanoparticles (NPs), and ultrafine particles (UFPs), were interchangeably used in the scientific communities. PM_0.1 originated from both natural and human sources. However, investigations of PM_0.1 and its effects on the environment, visibility, and human health risk to understand the levels of air pollution, sources, and impacts in South East Asia (SEA) countries continue to be lacking. The concentration of PM_0.1 in most SEA countries are much worse than those in western countries environment. A further motivation of this reviewed article is to provide a critical synthesis of the current knowledge and study of ambient PM_0.1 in SEA cities. The main influence of characteristics of PM_0.1 appears to be local sources including biomass burning and motor vehicles. Continuous monitoring of PM_0.1 in terms of both mass and number concentration should be further understood. A critical review is of great importance to facilitating air pollution control policies and predicting the behavior of PM_0.1 in SEA.

In this paper, the far field and near field optical responses of a gold nanoparticle are studied and simulated numerically. The electromagnetic field was excited by an electric dipole located near one end of the nanorod, which is used to model the emission of a quantum dot. Another excitation method was also simulated in which an incident plane wave is used. The excitation of dark plasmon modes of the gold nanorod is presented. The Poynting equation was solved numerically to study the influence of the gold nanorod on the dipole radiative power. In addition, the extinction cross section of the gold nanoparticle illuminated by the incident plane wave was calculated to estimate the amount of the scattered and absorbed light.

Iron (Fe), the main component of non-exhaust particulates, is known to have variable health effects that depend on the chemical species of iron. This study characterized the possible contribution of iron oxides and hydroxides to airborne brake-wear particles under realistic vehicle driving and braking conditions with different brake-pad friction materials. We found significant differences in wear coefficients and PM₁₀ emissions between non-asbestos organics (NAO) and European performance (ECE) brake pads. Iron was the dominant contributor to PM₁₀ and PM_2.5 brake-wear particles for both NAO and ECE. The iron concentration ratio in the particle mass were comparable to the disc to pads ratio measured by wear mass. The fact that magnetite, which is of interest with respect to health effects, was less abundant in NAO than in ECE suggested that tribo-oxidations occurred in NAO. Metallic iron is generated not only from abrasive wear but also from tribo-chemical reduction with magnetite as the starting material. We found differences not only in PM emissions between brake friction materials but also that the phase transformations of iron differed between friction materials. These differences were apparent in the distribution of iron oxides and hydroxides. Heat, tribo-oxidation, and tribo-reduction are intricately involved in these reactions.

Drought is one of the leading abiotic factors limiting morphological and physiological activities in blackberry cultivation. We investigated the effect of silver nanoparticles (AgNPs) on morphological and physiological processes in the boysenberry crop (Rubus ursinus Chamisso &amp; Schlenhtendal) under drought stress. The experiment was performed with three drought stress levels (0% PEG, 4% PEG and 8% PEG) and three AgNPs treatments (0, 0.1, 0.2 mg L−1) invitro conditions. The results showed that drought stress induced by PEG, reduced root and shoot development of boysenberry plants grown invitro. The addition of AgNPs is significantly alleviated the adverse effect of drought stress and increased the plant growth parameters. Antioxidant activity of SOD and CAT enzymes increased in boysenberry leaves when treated with AgNPs under drought conditions, while the amount of MDA decreased. Therefore, the results obtained in this study suggest that 0.1 mg L-1 AgNPs added to the medium improve the growth and development of invitro boysenberry plants under drought stress.

The novel Ionized Gas Thermoelectric Generator (IG-TEG) system that has been studied theoretically showing capabilities to continually extracting energy from the thermal energy of the ambient air, at low temperatures within the standard room temperature and below. This system does not need a temperature gradient in order to work, unlike the other TEGs that use Seebeck effect, and therefore this new system can be utilized for cooling purposes, by extracting energy instead of wasting energy in compressing the gas for cooling. This novel system was designed based on Static Ratchet Potential (SRP), which is known as a spatially asymmetric electric potential produced by an array of positive and negative electrodes. The ratchet potential produces electrical current from random Brownian Motion of charged particles that are driven by thermal energy. Ratchet potential was studied and investigated by several researches in the fields of sensing and energy harvesting. The main ratchet potential system parameter is the particles transportation, this parameter was studied under the condition of flashing ratchet potentials, and was analyzed based on several methods. In this study, a different approach is pursued to estimate particles transportation, by evaluating the charged particles distribution, and applying the other conditions of the SRP.

Standard Model is well-performing under the three-generation, but in the wake of more physics, fourth-generation leptons and quarks are introduced. In this paper, We will be reviewing various constraints surrounding quarks and leptons of 4th Generation and tried to show the importance of quarks to understand the baryogenesis. We talked about, reviewed existing parameters and set the updated lower limits of t’ and b’ by analysis. And predicted an updated version of lower mass bounds quarks and leptons. It is also reviewed that fourth generation leptons are primarily not possible because of disintegration of Higgs Boson and an interpretation has been setup. And in final, we talked about the Unified Standard Model.

Particles in classical physics are distinguishable objects, which can be picked out individually on the basis of their unique physical properties. By contrast, in quantum mechanics the standard view is that particles of the same kind (``identical particles'') are completely indistinguishable from each other. This standard view is problematic: Particle indistinguishability is irreconcilable not only with the very meaning of ``particle'' in ordinary language and in classical physical theory, but also with how this term is used in the practice of present-day physics. Moreover, the indistinguishability doctrine prevents a smooth transition from quantum particles to what we normally understand by ``particles'' in the classical limit of quantum mechanics. Elaborating on earlier work, we here discuss an alternative to the standard view that avoids these and similar problems. As it turns out, this alternative approach connects to recent discussions in quantum information theory concerning the question of when identical particles can be considered to be entangled.

We present a numerical study in which large-scale bulk simulations of self-assembled DNA constructs have been carried out with a realistic coarse-grained model. The investigation aims at obtaining a precise, albeit numerically demanding, estimate of the free energy for such systems. We then, in turn, use these accurate results to validate a recently proposed theoretical approach that builds on a liquid-state theory, the Wertheim theory, to compute the phase diagram of all-DNA fluids. This hybrid theoretical/numerical approach, based on the lowest order virial expansion and a nearest-neighbor DNA model, can provide, in an undemanding way, a thermodynamic description of DNA associating fluids that is in semi-quantitative agreement with experiments. We show that the predictions of such scheme are as accurate as the ones obtained with more sophisticated methods. We also demonstrate the flexibility of the approach by incorporating non-trivial additional contributions that go beyond the nearest-neighbor model to compute the DNA hybridization free energy.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

Solar energetic particles (SEPs) are bursts of high-energy particles that originate from the Sun and can last for hours or even days. The aim of this study is to understand how the characteristics of energetic particles was affected by the characteristic parameters of corotating interaction regions (CIRs). In particular, the particle intensity distribution with time and space in different CIRs are studied. The propagation and acceleration of particles are described by the focused transport equation (FTE). We used a three-dimensional magnetohydrodynamic (MHD) model to simulate the background field including CIRs. By changing the inner boundary conditions, we constructed CIRs with different solar wind speeds, angles between the polar axis and rotation axis, and the azimuthal widths of the fast streams. Impulsive particles are injected at the inner boundary. We then study the SEPs in different backgrounds. The results show that the CIR widths are related to the solar wind speed, tilt angles, and the azimuthal widths of the fast stream. The acceleration of particles in the reverse and forward compression regions is mainly influenced by the solar wind speed difference and the slow solar wind speed, respectively. Particles with lower energy (sub-MeV) are more sensitive to the parameters of CIRs. Different CIR parameters also greatly affect the spatio-temporal distribution of particle intensities in different ways. These results indicate that, it is crucial to consider the conditions of large-scale structure in interplanetary space when studying or predicting energetic particles. Additionally, our findings provide empirical guidance for forecasting the characteristics of SEPs.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Human exposure to foodborne inorganic nanoparticles (NPs) is a growing concern. However, identifying potential hazards linked to NP ingestion often requires long-term exposure in animals. Owing these constraints, intestinal organoids are a promising alternative to in vivo experiments, as such an in vitro approach should enable rapid and reliable assessment of the effects on the gut of ingested chemicals. However, this remains to be validated for inorganic substances. In our study, a transcriptomic analysis and immunofluorescence staining were performed to compare the effects of food-grade TiO2 (fg-TiO2) on enteroid-derived monolayers (EDMs) from murine intestinal organoids to known impacts of TiO2 on intestinal epithelium. After validating their ability to dose-dependently respond to a pro-inflammatory cytokine cocktail, EDMs were exposed to 0.1, 1 or 10 µg fg-TiO2/mL for 24h. In line with known data, a dose-related increase of muc2, vilin 1 and chromogranin A gene markers of cell differentiation was observed. In addition, fg-TiO2 induced apoptosis and dose-dependent genotoxicity, while a decreased expression of genes encoding for antimicrobial peptides, and of genes related to tight junction function was observed. These results validated the use of EDMs as a reliable model for toxicity testing of foodborne NPs likely to affect the intestinal barrier.

With the increase of global human activities, a large number of technogenic magnetic particles (TMPs) generated by industrial activities such as coal combustion, traffic and so on enter sediments on continental shelves. However, there is currently a lack of understanding of the spatiotemporal distribution of TMPs on continental shelves, as well as the sedimentary effects they cause. This review work comprehensively analyzes the source, morphology, composition, and spatiotemporal distribution characteristics of TMPs. Then it elucidates their magnetic contribution to sedimentary environments in continental shelf seas, as well as the influence of heavy metals and active iron. At the same time, the existing problems and future development directions of TMPs on continental shelves are summarized.

In a particle swarm with a fixed kinetic energy, the constituent particles move randomly and their velocity magnitudes follow a Maxwell distribution characterized by specific parameters. Within a certain time frame, particles in a sub-swarm may exhibit a bias in their movement direction. Thus, the particles may exhibit a special characteristic (biased random motion), where the group velocity in a particular direction remains constant u. For this biased particle swarm, composed of randomly moving particles with a fixed average speed c, particles have a higher probability of moving in a specific direction. Conversely, their likelihood of moving in all other directions is equally reduced. This study starts from the perspective of biased random walks and using Mathematica software proves that the diffusion rate of particles (in the reference frame R_u observed from R₀) in all directions is slower than that of an unbiased particle swarm with the same average speed c. Specifically, the degree of reduction is determined by the Lorentz-like factor. Lastly, we present the Ito equation for this biased random motion and provide associated verification examples. This study aims to serve as a reference for comprehending the underlying principles of the special relativity effect.

Biomimetic delivery systems (BDSs), inspired by the intricate designs of biological systems, have emerged as a groundbreaking paradigm in nanomedicine, offering unparalleled advantages in therapeutic delivery. These systems, encompassing platforms such as liposomes, protein-based nanoparticles, extracellular vesicles, and polysaccharides, are lauded for their targeted delivery, minimized side effects, and enhanced therapeutic outcomes. However, the translation of BDSs from research settings to clinical applications is fraught with challenges, including reproducibility concerns, physiological stability, and rigorous efficacy and safety evaluations. Furthermore, the innovative nature of BDSs demands a reevaluation and evolution of existing regulatory and ethical frameworks. This review provides an overview of BDSs, delve into the multifaceted translational challenges and present emerging solutions, underscored by real-world case studies. Emphasizing the potential of BDSs to redefine healthcare, we advocate for sustained interdisciplinary collaboration and research. As our understanding of biological systems deepens, the future of BDSs in clinical translation appears promising, with a focus on personalized medicine and refined patient-specific delivery systems.

Management of calcium and phosphate in biofluids is key to maintaining physiological mineral homeostasis (i.e., appropriate mineralization of hard tissues and an absence of mineral deposition in soft tissues). This review describes and contrasts the ways vertebrates manage calcium phosphate in two biological fluids (breast milk and serum) and illustrates the benefits of mineral sequestration by proteins. In milk, phosphoprotein-sequestered calcium magnesium phosphates provide nutritional support, whereas in serum, protein-sequestered calcium phosphates control transport and delivery of calcium and phosphate to tissues for biological function or excretion. In addition, subsets of sequestered phosphates in serum have been identified as culprits underlying ectopic deposition of calcium phosphates and toxicity.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

Rapid progress in gene editing based on clustered regularly interspaced short palindromic repeats/CRISPR-associated protein (CRISPR/Cas) has revolutionized the study of gene and genome function and genetic disease correction. While numerous genetically modified cellular and animal models have been created to understand biological processes, the clinical application of CRISPR/Cas tools has been impeded by off-targeting and delivery problems. It is generally accepted that the delivery of CRISPR in the form of a ribonucleoprotein complex (RNP) substantially reduces the time of DNA exposure to the effector nuclease, minimizing off-target effects and facilitating clinical usage. This review focuses on CRISPR/Cas RNP delivery with retro/lentiviral particles and exosomes, whose parallel production by cells transfected with viral vectors is underestimated. We critically evaluate specific mechanisms of extracellular particle formation and loading with CRISPR/Cas for each system. Additionally, the details of Cas-nanoparticle entry and uncoating, previously unappreciated in the context of gene editing efficiency, are discussed. Based on existing knowledge about the consequences of intervention in retroviral assembly, entry, or exosome formation, we outline the potential problems with CRISPR/Cas delivery using extracellular nanoparticles and ways to address them.

. This article presents, for the first time, the kinetics and the general features of a photopolymerization system (under visible light) G1/ Iodonium/ TEA/gold chloride (or A/B/N/G), having initial concentrations of A0, B0, N0 and G0, based on the proposed mechanism of Tar et al. Analytic formulas are developed to explore the new features including: (i) both FRP efficacy and the production of nanogold (NG) are proportional to the relative concentration ratios of (A0+B0+N0)/G0, which may be optimized for maximum efficacy; (ii) the two competing procedure of NG production and efficacy of free radical photopolymerization (FRP) can be tailored for optimal system with nanogold in the polymer matrix;(ii) the FRP efficacy is contributed by 3 components: the coupling of the excited state of copper complex (T) with the radicals (R and S) produced by the iodonium and the amine; (iii) the production of NG is contributed by 2 components: the coupling of T and radical (S) with gold ion; (iv) NG production has a transient state value which is an increasing function of light intensity and the combined concentration ratio [(A0/G0)+(N0/(K'M0). whereas it has a steady-state independent to the light intensity.

This paper is devoted to investigate charged vector particles tunneling via horizons of a pair of accelerating rotating charged NUT black hole under the influence of quantum gravitational effects. For this purpose, we use the modified Proca equation incorporating generalized uncertainty principle. Using the WKB approximation to the field equation, we obtain a modified tunneling rate and the corresponding corrected Hawking temperature for this black hole. Moreover, we analyze the graphical behavior of corrected Hawking temperature T'_H with respect to the event horizon for the given black hole. By considering quantum gravitational effects on Hawking temperatures, we discuss the stability analysis of this black hole. For a pair of black holes, the temperature T'_H increases with the increase in rotation parameters α and w, correction parameter β, black hole acceleration α and arbitrary parameter k and decreases with the increase in electric e and magnetic charges g.

It is suggested that physical properties of common elementary particles can be associated with microscopic Primordial Black Holes (PBH) which is inferred to have formed between 10⁻²⁴ to 10⁻²⁰ seconds from Big bang in the early universe. This is also found to be related to the phenomenon of Hawking radiation from these PBH. We have revisited the properties of minimons and maximons introduced by Markov [1] in this context. Planck particles which is inferred to form near Planck time (3.857 ×10⁻⁴³ seconds) are identified as maximons with a mass √πm_p where m_p is the Planck mass. The minimons are associated with a PBH with Hawking temperature identical with the cosmic microwave background temperature of the universe. The mass of the minimons are found to be comparable to that of the lightest neutrinos (0.0185 eV). They also possess highest Compton wavelength (10⁻⁴ m) known for an elementary particle.

Different types of gold nanoparticles have been synthesized that great potential in medical applications such as medical imaging, bio-analytical sensing and photothermal therapy. However, their stability, polydispersity and biocompatibility are major issues of concern. For example, the synthesis of gold nanorods, obtained through the elongated micelle process, produce them with a high positive surface charge that is cytotoxic. While gold nanoshells are unstable and within a few weeks they decompose due to Ostwald ripening. In this work, we report the self-assembly of the capsid protein of cowpea chlorotic mottle virus (CCMV) around spherical gold nanoparticles, gold nanorods and gold nanoshells to form virus-like particles (VLPs). All gold nanoparticles were synthesized or treated to give them a negative surface charge, so they can interact with the positive N-terminus of the capsid protein leading to the formation of the VLPs. To induce the protein self-assembly around the negative gold nanoparticles, we use different pH and ionic strength conditions that were determined from the capsid protein phase diagram. The encapsidation with the viral capsid protein confers them better biocompatibility, stability, monodispersity and a new biological substrate on which one can introduce specific ligands towards particular cells, broadening the possibilities of medical application.

Exposure to particulate matter (PM) causes considerable breathing-related health risks. We assessed the inhibitory effect of Siraitia grosvenorii extract (SGE) on airway inflammation in mice exposed to a fine dust mixture of PM10 (PM diameter &lt; 10 mm) and diesel exhaust particles (DEPs) known as PM10D. SGE attenuated neutrophil infiltration and the number of immune B and T cells in lung tissue and bronchoalveolar lavage fluid (BALF) of PM10D-exposed mice. SGE reduced the secretion of cytokines and chemokines, including interleukin (IL)-1a, tumor necrosis factor (TNF)- a, IL-17, chemokine (C-X-C motif) ligand (CXCL)-1, and macrophage inflammatory protein (MIP)-2 in BALF. Airway inflammation, accumulation of inflammatory cells, and collagen fibrosis in the lung after PM10D exposure were investigated by histopathological analysis, and SGE treatment ameliorated these symptoms. SGE decreased the mRNA expression of mucin 5AC (MUC5AC), CXCL-1, TNF-a, MIP-2, and transient receptor potential vanilloid and ankyrin 1 ion channels in the lung tissues of mice. Furthermore, SGE ameliorated mitogen-activated protein kinase (MAPK)/nuclear factor-kappa B (NF-κB) signaling activated by PM10D in mice. We conclude that SGE attenuated PM10D-induced neutrophilic airway inflammation via inhibiting MAPK/NF-κB activation. These results show that SGE may be a candidate for the treatment of inflammatory respiratory diseases.

To date, no scientific study has found evidence of an afterlife, and the mechanism of consciousness is two of the most challenging questions. Here, I show a hypothesis for consciousness and the probability of an afterlife through three simple thought experiments and theoretical evidence. More studies are needed to understand the mechanism precisely. I found that consciousness can be discussed based on a new theory. Here, I hypothesize that when a person or animal dies, the selection of a new nervous system's characteristic of a new life might depend on the characteristics of the final evolved yet unknown particle. Here, I suggest that the positive or adverse evolution of the said particle depends on the natural evolution of the materialistic brain's cognition, including intelligence. The fittest intellectuals, those who have a higher potential scan mind virus, may survive happier and help more for others to improve psychological well-being. Here, I suggest that when a brain dies, the two microparticles might emit at infinite speed from the dead brain and simultaneously bond with a naturally select suitable zygote or early nervous system somewhere in the universe/s, forming a new life with the impact of new nurture.

In order to study the effect of TiB2 particles on the mechanical properties of TiB2/6061Al composites, a series of TiB2/6061Al 3D representative volume element (RVE) were established based on SEM photos. This model took into account the ductile damage of the matrix and the traction separation behavior of the interface, and the linear damage evolution law was introduced to characterize the stiffness degradation behavior of the matrix elements. The mixed boundary conditions were used for RVE tensile experiments, and the accuracy of the predicted result was verified by the agreement of the experimental stress-strain curve. Results show that the addition of TiB2 particles can effectively promote the load-bearing capacity of the composite, but elongation is reduced. With the weight fraction of TiB2 increasing from 2.5% to 12.5%, the elastic modulus, yield strength, and tensile strength are increased by 8%, 10.37%, and 11.55% respectively, while the elongation decreased by 10%. The clustering rate of the TiB2 particles is also an important factor affecting the toughness of the composites. With the increase in the clustering rate of TiB2 particles from 20% to 80%, the load-bearing capacity of the composites is not improved, and the elongation of the composites is reduced by 8%. Moreover, the high strain region provides a fast expansion path for crack propagation and the particle spacing is a crucial factor that affects the stress field.

A cloud of relativistic material particles is considered, for which the distortions of length and time caused by the presence of the Lorentz factor an order of magnitude greater than curvature of space-time by gravity. The gravitational mass of the cloud is found in the region where its size is insignificant. It is established that the coefficient of dependence of the cloud mass on the total rest mass of its particles includes a complete elliptic integral of the 2nd kind.

This is an introduction to a new concept of quantum gravity that seamlessly merges General Relativity to the Standard Model. Based upon a novel patent-pending magnetic confinement method that was designed to emulate how our sun confines and rotates charged particles about a singularity; this confinement method uses a collective of off-centered confinement coils that are directed to curve rotating charged particles about a singularity in a way that allows charged particles to relatively accelerate from geodesic deviation. With this confinement method, the subtle Relative Accelerated Energy (RAE) from deviating charged particles has the capability to be focused and exponentially increased relative to the mass-energy of a closed system; which allows for a simple pathway to understand how black holes operate at their singularities. While in the pursuit of proving that this novel method of confinement mimics how our sun operates; I was also able to develop a logical explanation of how our sun reverses its magnetic poles and cycles using the core principles of Michael Faraday. If this concept of quantum gravity is correct, there is a simple explanation for the additional observed gravitational force about the galaxies that are said to obtain dark matter. In short, this theory of quantum gravity has the potential to fully discredit the existence of theorized dark matter with a simple experiment.

RNAi technology is a versatile, effective, safe, and eco-friendly alternative for crop protection. There is plenty of evidence of its use through host-induced gene silencing (HIGS) and spray-induced gene silencing (SIGS) techniques to control viruses, bacteria, fungi, insects, and nematodes. For SIGS, its most significant challenge is achieving stability and avoiding premature degradation of RNAi in the environment or during its absorption by the target organism. One alternative is encapsulation in liposomes, virus-like particles, polyplex nanoparticles, and bioclay, which can be obtained through the recombinant production of RNAi in vectors, transgenesis, and micro/nanoencapsulation. The materials must be safe, biodegradable, and stable in multiple chemical environments, favoring the controlled release of RNAi. Most of the current research on encapsulated RNAi focuses primarily on oral delivery to control insects by silencing essential genes. The regulation of RNAi technology focuses on risk assessment using different approaches; however, this technology has positive economic, environmental, and human health implications for its use in agriculture. The emergence of alternatives combining RNAi gene silencing with the induction of resistance in crops by elicitation and metabolic control is expected, as well as multiple silencing and biotechnological optimization of its large-scale production.

Structural and morphological properties of the hydronium-potassium jarosite microstructures were investigated in this work, and their electrical properties were evaluated. All microstructures were synthesized at a reasonable temperature of 343 K with a reduced reaction time of 3 hours. Increase in the pH from 0.8 to 2.1 decreased the particle sized from 3 µm to 200 nm and increasing the aging time from 0, 3 to 7 days resulted in semispherical, spherical and euhedreal jarosite structures, respectively. A Rietveld analysis also was done, finding that increasing pH, the amount of hydronium substitution by potassium in the cationic site also increases, having a 77.72 % of hydronium jarosite (JH) plus 22.29 % potassium jarosite (JK) at pH 0.8; 82.44 % (JH) and 17.56 % (JK) at pH 1.1, and 89.98 % (JH) plus 10.02 % (JK) at pH 2.1. The results obtained in this work show that the obtained hydronium potassium jarosite microstructures with reduced particle size and euhedreal morphology can be used as anode materials for improving the life time of lithium ion batteries, due that during the analysis of the voltage obtained using electrodes made with this particles and graphite, this ranged from 0.89 to 1.36 V.

In this paper, we analyze the Hawking radiation phenomenon for types of Banados-Teitelboim-Zanelli-like (BTZ-like) black holes. For this purpose, using the Hamilton-Jacobi method, we consider semi-classical WKB approximation to calculate the tunneling probabilities of massive boson particles. For these particles, we use the equation of motion for the Glashow-Weinberg-Salam model. Using quantum tunneling process of charged massive bossons, we compute the corresponding Hawking temperatures. Furthermore, we discuss the effects of rotation parameter on tunneling probability and temperature.

We prepared poly(3,4-ethylenedioxythiophene) (PEDOT)-coated sulfonated polystyrene copolymer particles as efficient heat-shielding agents, which showed strong near-infrared (NIR) absorption, with high solid contents and good solution stability. The poly(styrene sulfonate -co-styrene) (P(SS-co-St)) copolymers were successfully synthesized via radical solution polymerization, and PEDOT-coated P(SS-co-St) (PEDOT:P(SS-co-St)) was synthesized via Fe⁺-catalyzed oxidative polymerization. PEDOT:P(SS-co-St) was characterized by nuclear magnetic resonance and Fourier transform infrared spectroscopies. The particle size and morphology of PEDOT:P(SS-co-St) were examined using transmission electron microscopy, dynamic light scattering, and zeta potential measurements. The maximum NIR-shielding efficiency of the film was 92.0% with 40% transmittance. The high solution stability of PEDOT:P(SS-co-St) make it an ideal candidate for heat-insulating materials that find application in semi-transparent heat-insulator-coated windows.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

Respiratory syncytial virus (RSV) infection is a major cause of severe respiratory disease in infants and young children worldwide. Two vaccines targeting the elderly and pregnant women have been recently approved employing the prefusion form of the RSV-fusion protein (F). However, there are currently no vaccines for infants. Studies have shown a fusion-inactive prefusogenic F form is significantly more immunogenic and produces higher antibody titers to both the prefusion and postfusion structures of the F protein. Here we have developed RSV virus-like particles (RSV-VLPs) consisting of prefusogenic F, RSV glycoprotein and matrix proteins, produced them using the baculovirus expression system, and studied their protective efficacy in Balb/c mice. Morphology and successful assembly of VLPs were confirmed by transmission electron microscopy and western blot. Mice immunized with VLPs developed high levels of serum IgG and neutralizing antibodies as compared with mice immunized with inactivated virus. The VLP vaccine also induced higher levels of IFNγ and IL4, elicited limited proliferation of CD4+ and CD8+ T cells but higher cytotoxic-T-lymphocyte responses. VLP immunization abolished lung pathology in the mice after RSV challenge. Overall, our results indicate that RSV-VLPs consisting of prefusogenic F, glycoprotein and matrix proteins are a potential vaccine candidate against RSV.

This study introduces a neural network-based approach to predict dust emission, specifically PM2.5 particles, during almond harvesting in California. Using a feedforward neural network (FNN), the research predicts PM2.5 emissions by analyzing key operational parameters of an advanced almond harvester. The model is trained on extensive field data from the almond pickup system, including variables like brush speed, angular velocity, and harvester forward speed. The results demonstrate a notable predictive accuracy of the FNN model, with a Mean Squared Error (MSE) of 0.02 and a Mean Absolute Error (MAE) of 0.01, indicating a high degree of precision in forecasting PM2.5 levels. The study also finds a strong correlation between certain operational parameters and PM2.5 emissions, highlighting specific areas for optimization in harvesting techniques. By integrating machine learning with agricultural practices, this research provides a significant tool for environmental management in almond production, offering a method to reduce harmful emissions while maintaining operational efficiency. This model presents a solution for the almond industry and sets a precedent for applying predictive analytics in sustainable agriculture.

In this study, long-term mortality effects associated with exposure to PM10, PM2.5, BC (black carbon), and NOx were analyzed in a cohort in southern Sweden during the period from 1991‒2016. Participants (those residing in Malmö, Sweden, born between 1923‒1950) were randomly recruited from 1991‒1996. At enrollment, 30,438 participants underwent a health screening, which consisted of questionnaires about lifestyle and diet, a clinical examination, and blood sampling. Mortality data were retrieved from the Swedish national cause of death register. The modeled concentrations of PM10 (particles with an aerodynamic diameter smaller than or equal to 10 µm), PM2.5 (particles with an aerodynamic diameter smaller than or equal to 2.5 µm), BC (black carbon), and NOx (nitrogen oxides) at the cohort participants' home addresses were used to assess air pollution exposure. Cox proportional hazard models were used to estimate the associations between long-term exposure to PM10, PM2.5, BC, and NOx and the time until death among the participants during the period from 1991‒2016. The hazard ratios (HRs) associated with an interquartile range (IQR) increase in each air pollutant were calculated based on the exposure lag windows of the same year (lag0), 1‒5 years (lag1‒5), and 6‒10 years (lag6‒10). Three models were used with varying adjustments for possible confounders including both single-pollutant estimates and two-pollutant estimates. With adjustments for all covariates, the HRs for PM10, PM2.5, BC, and NOx in the single-pollutant models at lag1‒5 were 1.06 (95% CI: 1.02‒1.11), 1.01 (95% CI: 0.95‒1.08), 1.07 (95% CI: 1.04‒1.11), and 1.11 (95% CI: 1.07‒1.16) per IQR increase, respectively. The HRs were in most cases decreased by the inclusion of a larger number of covariates in the models. The most robust associations were shown for NOx, with statistically significant positive HRs in all models. An overall conclusion is that road traffic-related pollutants had a significant association with mortality in the cohort.

Low-cost particulate matter (PM) sensors offer an excellent opportunity to improve our knowledge about this type of pollution. Their size and their cost, which support multi-node network deployment, along with their temporal resolution, enable them to report fine spatio-temporal resolution for a given area. These sensors have known issues across performance metrics. Generally, the literature focuses on the PM mass concentration reported by these sensors but some models of sensors also report particle number concentrations (PNC) segregated into different PM size bins. In this study, 8 units of each Alphasense OPC-R1, Plantower PMS5003 and Sensirion SPS30 have been exposed, under controlled conditions, to short-lived peaks of PM generated using two different combustion sources of PM, exposing the sensors to different particle size distributions to quantify and better understand the low cost sensors performance across a range of relevant environmental ranges. The PNC reported by the sensors were analysed. This study showed that there is added value in directly using the PNC reported by the sensors instead of the mass concentrations, which could aid the efforts to calibrate these sensors to a known accuracy. It demonstrated that all sensors tested here could track the fine temporal variation of PNC, that the Alphasense OPC-R1 could closely follow the variations of size distribution between the two sources of PM, and it showed that particle size distribution and composition are more impactful on the sensors measurement than relative humidity.

Features of nanosecond discharge development in a non-uniform electric field are studied experimentally. High spatial resolution imaging showed that thin luminous tracks of great length with a cross-section of a few microns are observed against the background of discharge glow in air and argon. It has been established that the detected tracks are adjacent to brightly luminous white spots on the electrodes or to the vicinity of these spots, and are associated with the flight of small particles. It is shown that the traces have various shapes and change from pulse to pulse. The particle tracks may look like curvy or straight lines. In some photos, they can change the direction of movement to the opposite. The particle trace was found to abruptly cut off and a bright flash is visible at the trail break point. The color of the tracks differs from that of the spark leaders, while the bands of the second positive nitrogen system dominate in the gap spectra during the existence of a diffuse discharge. Areas of blue light are evident near the electrodes, as well. Development of glow in the gap during its breakdown is revealed using an ICCD camera. Physical reasons for the observed phenomena are discussed.

Large quantities of real-time particle data are becoming available from low-cost particle monitors. However, it is crucial to determine the quality of these measurements. The largest network of monitors in the United States is maintained by the PurpleAir company, which offers two monitors: PA-I and PA-II. PA-I monitors have a single sensor (PMS1003) and PA-II monitors employ two independent PMS5003 sensors. We determine a new calibration factor for the PA-I monitor and revise a previously published calibration algorithm for PA-II monitors (ALT-CF3). From the PurpleAir API site, we downloaded 83 million hourly average PM2.5 values in the PurpleAir database from Washington, Oregon, and California between January 1, 2017 and September 8, 2021. Daily outdoor PM2.5 means from 194 PA-II monitors were compared to daily means from 47 nearby Federal regulatory sites using gravimetric Federal Reference Methods (FRM). We find a revised calibration factor of 3.4 for the PA-II monitors. For the PA-I monitors, we determined a new calibration factor (also 3.4) by comparing 26 outdoor PA-I sites to 117 nearby outdoor PA-II sites. These results show that PurpleAir PM2.5 measurements can agree well with regulatory monitors when an optimum calibration factor is found.

The Covid-19 has hit Italy in February 2020 after its outbreak in China at the beginning of January. But why Italy first among Western countries? What are the conditions that made Italy more vulnerable and the first target of such disease? What characteristics and what diffusion patterns could be highlighted and hypothesized, from the outbreak to the end of March 2020, after containment measures - including a national lock down – were introduced? In this paper we try to provide some answers to these questions, analyzing the issue from the medical, geographical and planning points of view. In particular, we started from a hypothesis of very similar economic, geographical, climatic and environmental conditions of the areas of Wuhan – in Hubei Province in China, the outbreak of the epidemics – and the Po Valley area – in Italy – where most cases and deaths were registered. Adopting an ecological approach, we compared the spatial distribution and pattern of Covid-19-related mortality in Italy with several geographical, environmental and socio-economic variables at Provincial level, analyzing them by means of spatial analytical techniques as LISA – Local Indicators of Spatial Association. Possible evidence relating Covid-19 cases and Nitrogen-related pollutants and land take arise, particularly in the Po Valley area.

The amount of outdoor particles that indoor environments receive depends on the particle infiltration factors (Fin), peculiar of each environment, and on the outdoor aerosol concentrations and size distributions. The respiratory doses received, while residing indoor, will change accordingly. This study aims to ascertain to what extent such doses are affected by the vertical distance from the traffic sources. Particle number size distributions have been simultaneously measured at street level and at about 20 m height in a street canyon in downtown Rome. The same Fin have been adopted to estimate indoor aerosol concentrations, due to the infiltration of outdoor particles and then the relevant daily respiratory doses. Aerosol concentrations at ground floor were more than double than at 20 m height and richer in ultrafine particles. Thus, although aerosol infiltration efficiency was on average higher at 20 m height than at ground floor, particles more abundantly infiltrated at ground level. On a daily basis, this involved a 2.5-fold higher dose at ground level than at 20 m height. At both levels, such doses were greater than those estimated over the period of activity of some indoor aerosol sources, therefore they represent an important contribution to the total daily dose.

A rigorous model for the electron is presented by generalizing the Coulomb's Law or Gauss's Law of electrostatics, using a unified theory of electricity and gravity. The permittivity of the free-space is allowed to be variable, dependent on the energy density associated with the electric field at a given location, employing generalized concepts of gravity and mass/energy density. The electric field becomes a non-linear function of the source charge, where concept of the energy density needs to be properly defined. Stable solutions are derived for a spherically symmetric, surface-charge distribution of an elementary charge. This is implemented by assuming that the gravitational field and its equivalent permittivity function is proportional to the energy density, as a simple first-order approximation, with the constant of proportionality referred to as the Unifield Electro-Gravity (UEG) constant. The stable solution with the lowest mass/energy is assumed to represent a ``static'' electron without any spin. Further, assuming that the mass/energy of a static electron is half of the total mass/energy of an electron including its spin contribution, the required UEG constant is estimated. More fundamentally, the lowest stable mass of a static elementary charged particle, its associated classical radius, and the UEG constant are related to each other by a dimensionless constant, independent of any specific value of the charge or mass of the particle. This dimensionless constant is numerologically found to be closely related to the the fine structure constant. This possible origin of the fine structure constant is further strengthened by applying the proposed theory to successfully model the Casimir effect, from which approximately the same above relationship between the UEG constant, electron's mass and classical radius, and the fine structure constant, emerges.

The science on the anthropogenic airborne aerosols impacting upon the World Heritage marble monument, the Taj Mahal, at Agra has been studied in the light of modern physico-chemical approaches. The study is an effort to understand yet unrecognized airborne species which were found on the surface of the Taj Mahal monument. These species have been analyzed in the light of current analytical methods to impart characterization features and their possible impacts on the surface of the marble. Chemical constituents of these substrates which were incorporated over the top surface of the monument have been identified. Interestingly, the carbon particulates which were thought in the micro level, popularly called “particulate matters” has now been identified even in the nano domain entity, which are chemically more reactive, have been found on the surface of the monument. Because of their high chemical activity these nano carbons do play newer chemistry in the presence of air and sunlight generating several reactive oxygen species (ROS).These ROS are capable to respond to complicated chemical reactions on the surface of the marble in association with deposited cyanophyceae and other deposits of plant origin causing rapid degradation. This study provides the nature of onslaught borne out by such monument exposed under the prevalent smoggy environmental scenario.