This study proposes a 3D particle-base (discrete) multiphysics approach for modelling calcification in the aortic valve. Different stages of calcification (from mild to severe) were simulated, and their effect on the cardiac output assessed. The cardiac flow rate decreases with the level of calcification. In particular, there is a critical level of calcification below which the flow rate decreases dramatically. Mechanical stress on the membrane is also calculated. The results show that, as calcification progresses, spots of high mechanical stress appear. Firstly, they concentrate in the regions connecting two leaflets; when severe calcification is reached, then they extend to the area at the basis of the valve.

MoS2 lithium-based grease is suitable for lubrication protection between bearings at high temperatures and loads due to its excellent tribological properties. However, there is little research on the influence of different addition methods of MoS2 additive on the tribology and corrosion properties of lithium grease. In this work, vegetable oil with low toxicity, high biodegradation rate, and low cost was selected as the base oil, lithium 12-hydroxystearate as the thickener, and MoS2 as the additive. The effects of different adding modes of MoS2 on the tribology and corrosion properties of lithium grease were studied. The experimental results showed that adding 0.01wt% MoS2 before thickening was more conducive to improving the tribological properties of lithium grease. The average friction coefficient was 0.034, and the average spot diameter was reduced by 0.16mm. After grinding and adding 0.01wt% MoS2, the corrosion inhibition efficiency of the steel sheet was as high as 96.97%. The main reason was that the longer stirring and grinding were conducive to the uniform distribution of MoS2 in the grease, and the protective film formed by MoS2 and GCr15-bearing steel improved the lubrication performance and corrosion inhibition performance of the friction system.

Deployment of unmanned aerial vehicles (UAVs) as aerial base stations (ABSs) has been considered to be a feasible solution to provide network coverage in scenarios where the conventional terrestrial network is overloaded or inaccessible due to an emergency situation. This article studies the problem of optimal placement of the UAVs as ABSs to enable network connectivity to the users in a coverage free zone. The main contributions of this work include two approaches to position the UAVs and to assign user equipment (UE) to each UAV, such that the sum-rate and the coverage probability of the network is maximized. An approach can be selected depending on the prevailing scenario. The first approach uses clustering algorithm to determine the 2D positioning of the UAV and a matching algorithm is used for UE assignment by considering the characteristics of the air-to-ground propagation channels as well as the impact of co-channel interference from ABSs. Then it uses exhaustive search on different altitudes to find the optimal altitude. In the second approach, 2D positioning and UE assignment are done similarly to the first approach. However, the sub-optimal altitude is estimated using particle swarm optimization (PSO). The first approach is suitable for a system which has computational resource constraints or lower probability of line of sight (LoS) links. In contrast, the second approach is suitable for data rate greedy systems or a higher probability of LoS links.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

The inverse finite element method (iFEM) is a novel method for reconstructing the full-field displacement of structures by discrete measurement strain. In practical engineering applications, the accuracy of iFEM is reduced due to the positional offset of strain sensors during installation, and errors in structural installation. Therefore, coarse and fine two-stage calibration (CFTSC) method is proposed to enhance the accuracy of the reconstruction of structures. Firstly, the coarse calibration is based on a single-objective particle swarm optimization algorithm to optimize the displacement-strain transformation matrix related to the sensor position. Secondly, as selecting different training data can affect the training effect of self-constructed fuzzy networks, this paper proposes to screen the appropriate training data based on residual analysis. Finally, the experiments of the wing integrated antenna structure verify the efficient of the method on the reconstruction accuracy of the structural body displacement field.

The efficacy of weed management depends on the correct control timing according to the seedling emergence dynamics. Since soil temperature and soil moisture are two main factors that determine weed germination, the hydrothermal time model can be used to predict their emergence. The aim of this study was to estimate the base temperature (Tb) and base water potential (Ψb) for germination of Chenopodium album, Amaranthus retroflexus, Setaria pumila and Panicum capillare collected from fields in continental Croatia and then to compare these values with those of Italian populations embedded in the AlertInf model. Germination tests were performed at seven constant temperatures (ranging from 4 to 27°C) and eight water potentials (0.00 to - 1.00 MPa). Estimated Tb and Ψb were 3.4°C, -1.38 MPa for C. album, 13.9°C, -0.36 MPa for A. retroflexus, 6.6°C, -0.71 MPa for S. pumila and 11.0°C, -0.87 MPa for P. capillare, respectively. According to the criterion of overlap of the 95% confidence intervals, only Tb of C. album, and Ψb of A. retroflexus were similar between Croatian and Italian populations. Further field experiments should be conducted in the Croatian field to monitor weed emergence patterns of C. album and to calibrate the AlerInf equation parameters.

Although Eulerian approaches are standard in computational acoustics, they are less effective for certain classes of problems like bubble acoustics and combustion noise. A different approach for solving acoustic problems is to compute with individual particles following particle motion. In this paper, a Lagrangian approach to model sound propagation in moving fluid is presented and implemented numerically, using three meshfree methods to solve the Lagrangian acoustic perturbation equations (LAPE) in the time domain. The LAPE split the fluid dynamic equations into a set of hydrodynamic equations for the motion of fluid particles and perturbation equations for the acoustic quantities corresponding to each fluid particle. Then, three meshfree methods, the smoothed particle hydrodynamics (SPH) method, the corrective smoothed particle (CSP) method, and the generalized finite difference (GFD) method, are introduced to solve the LAPE and the linearized LAPE (LLAPE). The SPH and CSP methods are widely used meshfree methods, while the GFD method based on the Taylor series expansion can be easily extended to higher orders. Applications to modeling sound propagation in steady or unsteady fluids in motion are outlined, treating a number of different cases in one and two space dimensions. A comparison of the LAPE and the LLAPE using the three meshfree methods is also presented. The Lagrangian approach shows good agreement with exact solutions. The comparison indicates that the CSP and GFD method exhibit convergence in cases with different background flow. The GFD method is more accurate, while the CSP method can handle higher Courant numbers.

Contrapose the highly integrated, multiple types of faults and complex working conditions of aircraft Electro Hydrostatic Actuator (EHA), to effectively identify its typical faults, we propose a fault diagnosis method based on the fusion convolutional neural networks (FCNN). First, the aircraft EHA fault data is encoded by GADF to obtain the fault feature images. Then we build an FCNN model that integrates the 1DCNN and 2DCNN, where the original 1D fault data is the input of the 1DCNN model, and the feature images obtained by GADF transformation are used as the input of 2DCNN. Multiple convolution and pooling operations are performed on each of these inputs to extract the features, next these feature vectors are spliced in the convergence layer, and the fully connected layers and the Softmax layers are finally used to attain the classification of aircraft EHA faults. Furthermore, the multi-strategy hybrid particle swarm optimization (MSPSO) algorithm is applied to optimize the FCNN to obtain a better combination of FCNN hyperparameters; MSPSO incorporates various strategies, including an initialization strategy based on homogenization and randomization, and an adaptive inertia weighting strategy, etc. The experimental result indicates that the FCNN model optimized by MSPSO achieves an accuracy of 96.86% for identifying typical faults of the aircraft EHA, respectively higher than the 1DCNN and the 2DCNN about 16.5% and 5.7%. Additionally, the FCNN model improved by MSPSO has a higher accuracy rate when compared to PSO.

The reactive nature of traditional frequency stability methods can lead to delayed corrective actions and unnecessary loss-of-load. This work presents a distributed model predictive control method for proactive power system frequency stability. Dynamic state estimation model is derived through a particle filter. By being able to estimate the future state of frequency, corrective actions can be taken before the system reaches a critical condition. Proactive approach makes it possible to optimize the response to a disturbance, which results in a decrease of the amount of compensation utilized. The method is tested via Matlab simulations based on Kundur's Two-Area System, and the IEEE 14-Bus system. Performance metrics are provided and evaluated against other contemporary solutions found in literature. Easy-to-derive model, without hard-to-design parameters, indicate potential towards real-life applications.

Single particle analysis with cryogenic electron microscopy (cryo-EM) can determine high resolution structures of macromolecular assemblies. To reconstruct final three-dimension(3D) density map, a reliable initial model is essential and ab-initio reconstruction usually can avoid model bias. The grand challenge for ab-initio reconstruction is to alignment two-dimension(2D) low signal-to-noise ratio(SNR) of particle images with random and unknown parameters. Here we formulate a fast ab initio reconstruction method(named AlignFM) based on Fourier Mellin transform and particle-swarm intelligence optimization(PSO) algorithm. It enables simultaneous 2D alignment and 3D refinement, which can fast generate a reliable 3D map. After experiments on several real datasets. AlignFM shows high performance on fast ab initio reconstruction with a small amount of data.

We review some properties of a relativistic classical massless charged particle with spin interacting with an external electromagnetic field. We give in particular a proper definition of kinetic energy and total energy, the latter being conserved when the external field is stationary. We find that the particle’s velocity may differ from c as a result of the spin - electromagnetic field interaction, without jeopardizing Lorentz invariance.

Understanding tumor attachments and management of feeding arteries are very important factors to achieve safe resection of skull base meningioma. We examined the distributions and frequencies of feeding arteries in skull base meningioma by cerebral angiography, and also assessed relationships to tumor attachment for skull base meningioma. We enrolled patients with skull base meningioma who underwent MRI and cerebral digital subtraction angiography (DSA), from September 2015 to October 2022. Subjects comprised 115 patients (32 males, 83 females; mean age, 52.7 years) with 117 meningiomas showing tumor attachments around the “cavernous sinus to upper part of the clivus” (Area 1), “lower part of the clivus to foramen magnum” (Area 2), and “tentorium around the petrous bone” (Area 3). We examined feeding arteries based on cerebral angiography and counted the number of related feeding arteries. Particularly frequent arteries, such as the dorsal meningeal artery (DMA), ascending pharyngeal artery (APA), tentorial artery (TA), and petrosal branch (PB) of the middle meningeal artery (MMA) were analyzed for associations of tumor attachment to Areas 1–3. DMA, APA, TA, and PB are very frequent feeding arteries among skull base meningiomas. In some cases, the artery of the foramen rotundum, posterior ethmoidal artery, recurrent meningeal artery, posterior meningeal artery, etc., supply blood to the skull base meningioma. Meningiomas with DMA as a feeding artery correlated strongly with tumor attachment to Area 1 (p<0.001). Meningiomas with APA correlated strongly with tumor attachment to Area 2 (p<0.001). Meningiomas with TA correlated strongly with tumor attachment to Area 3 (p<0.001). PB correlated with Area 3 (p<0.05). Visualization of these arteries suggests tumor attachments to the correlated areas. An accurate anatomical understanding of tumor attachment and feeding arteries is essential to determine appropriate surgical strategies for skull base meningioma. Pre-operative DSA can provide further understanding of the feeding arteries and attachments of skull base meningioma.

Proteasomes critically regulate proteostasis via protein degradation. Proteasomes are multisubunit complexes composed of the 20S proteolytic core particle (20S CP) that, in association with one or two 19S regulatory particles (19S RPs), generate the 26S proteasome. 26S is the major proteasomal complex in the cells. Native gel protocols are used to investigate the 26S/20S ratio. However, a simple method for detecting these proteasome complexes in the cells is missing. To this end, using CRISPR technology, we YFP tagged the endogenous PSMB6 (b1) gene, a 20S CP subunit, and co-tagged endogenous PSMD6 (Rpn7), a 19S RP subunit, with mScarlet fluorescent protein. We observed colocalization of YFP and mScarlet fluorescent proteins in the cells, with higher nuclear accumulation. Nuclear proteasomal granules are formed under osmotic stress, and all were positive for YFP and mScarlet. Previously we have reported that PSMD1 knockdown, one of the 19 RP subunits, gives rise to a high level of “free” 20S CP. Intriguingly, under this condition, the 20S-YFP remained nuclear, whereas the PSMD6-mScarlet is mostly in cytoplasm, demonstrating the distinct subcellular distribution of uncapped 20S CP. Lately, we have shown that the PSMA3 (a7) C-termininus, a 20S CP subunit, binds multiple intrinsically disordered proteins (IDPs). Remarkably, truncation of the PSMA3 C-terminus is phenotypically reminiscent of PSMD1 knockdown. These data suggest the PSMA3 C-terminal region is critical for the 26S proteasome integrity.

One of the most widely available and extensively produced varieties of industrial hemp, which generates a substantial amount of consumer-increasing waste in the form of hemp cellulose. In this study, recycling with a compressed and high-speed method that combines crushing and alkali treatment effectively converts leftover hemp fiber into ultrafine powder. SEM (Scanning Electron Microscopy), AFM (Atomic Force Microscope), FTIR (Fourier-transform Infrared Spectroscopy), and XRD (X-ray Diffraction) examined the original morphology of hemp fiber treated with alkali, fiber heated to 200 ℃, and crushed powder. Particle size, crystallinity, fiber surface, and strength increased and decreased. It became apparent that fiber strength decreased and fiber roughness significantly increased after alkali treatment. Fiber increased significantly, and crystallinity decreased after crushing. It was simple and effective for converting the leftover hemp fiber into micron-sized powder. In about 3 to 5 minutes, approximately 1 kg of dry ultrafine powder with a particle size of 10.44 μm was produced. This production method will significantly enhance future industrial applications of waste hemp fiber.

To enable purposeful design and implementation of automated concrete technologies, precise assessment and prediction of the complex material flow at various stages of the process chain are necessary. This paper investigates the intermediate stage of the extrusion and deposition processes in extrusion-based 3D-concrete-printing, using a numerical model based on the Particle Finite Element Method (PFEM). In PFEM, due to the Lagrangian description of motion, remeshing algorithms and the alpha shape method are used to track the free surface during large deformation scenarios. The Bingham constitutive model was used for describing the rheological behaviour of fresh concrete. This model is validated by comparing the numerically predicted layer geometries with those obtained from laboratory 3D printing experiments. Extensive parametric studies were then conducted using the numerical simulation, delineating the influence of process and material parameters on the layer geometries, the dynamic surface forces generated under the extrusion nozzle and the inter-layer interactions.

Lipophilicity can be measured with different methods, such as Shake-Flask or liquid chromatography. HPLC presents the advantage of overcoming solubility issues and therefore extending the range of lipophilicity to high values. A specific HPLC method, called ELogD, had been developed 20 years ago on a C₁₆-amide stationary phase, enhancing hydrophobic and hydrogen bond interactions to mimic octanol-water partition. The emergence of novel stationary phases added to the need for a less complex mobile phase has led to the development of a new HPLC assay called alphaLogD, applicable to neutral and basic compounds at pH 7.4, that combines superficially porous particles, a high number of equilibriums between solutes and stationary phase, and results in a lower number of isocratic methods to determine the logk’_w at a higher throughput. Statistical studies have been run to successfully evaluate the alphaLogD method compared to the Shake-Flask method and to allow this lipophilicity measurement into the so-called Beyond-Rule-of-5-molecules space.

One of the industries with the fastest rate of growth is healthcare, and this industry's enormous data requires extensive cloud storage. The cloud may offer some protection, but there is no assurance that data owners can rely on it for refuge and privacy amenities. Therefore, it is essential to offer security and privacy protection. Increased customer satisfaction with security and privacy preservation is crucial since healthcare big data and its sources are stored in the cloud and contain increasingly private and sensitive information. However, maintaining privacy and security in an untrusted green cloud environment is difficult, thus the data owner should have complete data control. A new work SecPri-BGMPOP(security and privacy of Boost graph Convolutional Network -Pinpointing-Optimization Performance) is suggested that can offer a solution that involves several different steps in order to handle the numerous problems relating to security and protecting privacy. Initially Boost Graph Convolutional Network Clustering (BGCNC) algorithm, which reduces computational complexity in terms of time and memory measurements, is first applied to the input dataset to begin the clustering process. Second, enlarge by employing a piece of the magnifying bit string to generate a safe key, pinpointing based encryption avoids amplify leakage even if a rival or attacker decrypts the key or asymmetric encryption. Finally, to determine the accuracy of the method, an optimal key was created using a meta-heuristic algorithmic framework called Hybrid fragment horde bland lobo Optimization (HFHBLO). Our proposed method currently kept in a cloud environment, allowing analytics users to utilize it without risking their privacy or security.

A calculation is presented for the mass relationships between electron, muon and the tau particle. It is shown that charged leptons with mass levels beyond the one of the tau particle cannot exist because of insufficient binding energy. The underlying mechanism of the relationship between the leptons is the isospin feature of Dirac particles, which appears being a substantial attribute next to nuclear angular spin. It is further shown that the energy of the elementary electric charge, such as embodied by the mass of an electron, is due to the interaction between the isospins of the pion’s quark and antiquark.

The primary objective of this research was to assess the energy consumption of the gas treatment units at Bonny NLNG Refinery, the first Gas Refinery in Rivers State, Nigeria, while utilizing semi-lean amine. To achieve this goal, a simulation of the units was conducted using the advanced software package Aspen Hysys (V.8.3). The simulation was designed to accurately represent the dynamic behavior of the refinery's gas treatment units, allowing for a comprehensive analysis of their energy usage. The research aimed to quantify the energy consumption of the gas treatment units and identify opportunities for energy optimization. By utilizing semi-lean amine, which is known to improve energy efficiency, the study sought to evaluate the potential energy savings that could be achieved in the refinery's operations. The simulation model incorporated the specific design and operational parameters of the gas treatment units at Bonny NLNG Refinery, including the gas flow rate, lean amine concentration, absorber pressure, stripping temperature, amine circulation rate, and acid gas removal efficiency. By considering these parameters, the simulation accurately represented the dynamic behavior of the gas treatment units, enabling a detailed analysis of their energy consumption. Through the simulation, various scenarios and operational conditions were evaluated to determine the optimal set of parameters that minimized energy consumption. The research also examined the trade-offs between energy consumption, acid gas removal efficiency, and other performance indicators, such as amine circulation rate and regeneration efficiency. The findings of this research have significant implications for the energy efficiency and sustainability of gas treatment operations at Bonny NLNG Refinery. By identifying opportunities for energy optimization and providing recommendations for the utilization of semi-lean amine, the study contributes to the development of more efficient and environmentally friendly gas treatment processes. Overall, this research combines advanced simulation techniques with a comprehensive analysis of energy consumption to provide valuable insights into the energy efficiency of gas treatment units at Bonny NLNG Refinery, enabling informed decision-making and potential improvements in energy utilization. By utilizing the percentage-based unit simulation approach, a detailed examination of the energy consumption patterns was obtained. This analysis provides valuable insights into the operational efficiency and determination of potential energy-saving opportunities within the gas treatment units. This study specifically focuses on the integration of an absorption column split stream (stream flow) and a flash unit as a potential means to reduce the energy consumption of gas treatment devices. The integration of these units aims to optimize the overall energy efficiency of the gas treatment process by recovering and utilizing waste heat and reducing energy losses. The absorption column split stream allows for the diversion of a portion of the gas stream to a flash unit before entering the absorber. The flash unit operates at a lower pressure, which facilitates the release of entrained hydrocarbons and reduces the overall energy requirements for gas treatment. By separating and recovering the hydrocarbons in the flash unit, energy losses associated with their absorption and subsequent regeneration are minimized. Through the simulation, the study analyzes the energy consumption patterns of the gas treatment units with and without the integration of the absorption column split stream and flash unit. Comparative assessments are conducted to evaluate the energy savings and overall operational efficiency achieved through this integration. The findings of this research will provide valuable insights into the potential energy-saving opportunities offered by the integration of the absorption column split stream and flash unit in gas treatment devices. It will help refine the design and operation of gas treatment units, enabling more energy-efficient processes in the gas refining industry. By optimizing energy consumption in gas treatment units, the study contributes to the industry's goals of reducing greenhouse gas emissions and improving sustainability. The integration of the absorption column split stream and flash unit offers a promising approach to enhance energy efficiency, reduce operational costs, and minimize environmental impact. Overall, this research underscores the importance of exploring innovative solutions, such as the integration of different process units, to achieve energy savings in gas treatment operations. Through a comprehensive analysis of energy consumption patterns, this study aims to provide practical recommendations for optimizing energy efficiency in gas treatment units, fostering a more sustainable and efficient gas refining industry.The research specifically explores the impact of integrating the absorption column split stream and flash unit when dealing with sour gas streams containing carbon dioxide concentrations of less than mole ℅, while utilizing MDEA fluid as the solvent. Through comprehensive analysis and simulation using advanced software tools, the study demonstrates that by incorporating the absorption column split stream and flash unit, a significant reduction in device energy consumption of up to 10% can be achieved. The integration of the absorption column split stream and flash unit offers promising opportunities to enhance the energy efficiency of gas treatment devices. By diverting a portion of the gas stream to the flash unit, the separation of hydrocarbons and the subsequent release of entrained hydrocarbons at lower pressure significantly reduce the overall energy requirements for gas treatment. The comprehensive analysis and simulation conducted in the research provide concrete evidence of the energy-saving potential of this integration. By quantifying the energy consumption patterns and comparing scenarios with and without integration, the study establishes the effectiveness of the approach and its impact on operational efficiency. The findings of the research highlight the importance of considering the specific gas composition and utilizing appropriate solvents, such as MDEA, for optimizing energy efficiency. The integration of the absorption column split stream and flash unit not only reduces energy consumption but also offers the potential for cost savings and environmental benefits. Overall, the research demonstrates that by incorporating the absorption column split stream

ABSTRACT"In the realm of the industrial complex, a pressing concern lies in optimizing resource utilization and enhancing energy efficiency. This critical issue finds strong support from a variety of government programs, strategies, and regulatory documents. To effectively tackle this challenge and revolutionize petrochemical production, it is imperative to establish and develop innovative mechanisms. One such mechanism involves harnessing the power of automation and advanced Industry 4.0 technologies to streamline production processes. By doing so, we can unlock the full potential of these systems, driving operational efficiency, conserving valuable reserves, and propelling innovation within the petrochemical industry."The article delves into an in-depth analysis of the prominent trends in the application of the "Industry 4.0" concept within the petrochemical industry. It sheds light on the various factors that impact the efficiency of organizing production systems. Additionally, the article identifies the primary avenues that drive the advancement and enhancement of production organization practices. Moreover, the article explores the fundamental tools employed for process improvements and highlights the significance of process automation in petrochemical plants. By examining these key aspects, it aims to provide valuable insights and recommendations for leveraging Industry 4.0 technologies to optimize production processes in the petrochemical industry..The study focuses on examining and evaluating various systems and technologies that contribute to the optimization of production processes within the petrochemical industry. Specifically, it delves into the implementation and benefits of the just-in-time system, the 5S system for workplace rationalization, as well as different information systems including ERP systems and CALS-technologies. By exploring these systems and technologies, the article aims to identify the advantages of automating production processes within the petrochemical complex. This analysis will unveil the potential benefits such as improved efficiency, reduced waste, enhanced productivity, streamlined operations, and increased overall competitiveness. Through this research, we aim to shed light on the value of these automation solutions and their impact on driving the petrochemical industry towards greater success.

This research was conducted on the Maribaya Timur school community in Lembang Subdistrict, West Bandung Regency, Indonesia, which is an active community in the area that is threatened by the potential for earthquake disasters due to the active Lembang fault. Disaster risk reduction efforts are pursued through increasing school-based preparedness that involves members of the school community, surrounding communities and various institutions that are associated with reducing the risk of school-based earthquake. Increasing preparedness against earthquakes focuses more on aspects of capacity building of school communities in reducing disaster risk, while aspects of vulnerability and threats have not been the focus of disaster risk reduction. The steps taken refer to the element of preparedness by aligning with the conditions, needs and potential that exist in the school community. Theoretically, if the school community has preparedness to face an earthquake disaster, the risk of earthquake disaster in the school community will be reduced so that it can minimize losses, victims and suffering that will be caused by the earthquake disaster.

The non-symmetrical collapse of an empty cylindrical cavity is modelled using Smoothed Particle Hydrodynamics. The presence of a nearby surface produces an anisotropic pressure field generating a high velocity jet that hits the surface. The collapse follows a different dynamic based to the initial distance between the centre of the cavity and the surface. When the distance is greater than the cavity radius (detached cavity) the surface is hit by travelling shock waves. When the distance is less than the cavity radius (attached cavity) the surface is directly hit by the jet and later by other shock waves generated in the last stages of the of the collapse. The results show that the surface is hit by a stronger shock when distance between the centre of the cavity and the surface is zero while showing more complex double peaks behaviour for other distances.

The Selective Paste Intrusion (SPI) method is a layer-by-layer additive manufacturing technique that allows for the production of complex geometries in concrete elements by selectively bonding aggregates with cement paste in a particle bed. To create reinforced concrete, the Wire and Arc Additive Manufacturing (WAAM) process shall be integrated into SPI. This technique allows the production of almost free-formed reinforcement and thus complements the advantage of SPI to produce free-formed structures of almost any geometry. However, integration of WAAM into SPI poses a considerable challenge, as high temperatures are generated during the welding process. These temperatures can negatively affect the rheological properties of the cement paste, in turn the penetration behavior of the paste in the particle bed and, subsequently, the mechanical properties of the hardened concrete. A possible passive cooling strategy is to increase the protruding length of the reinforcement bars out of the particle-bed. This requires that the distance of the print nozzle to the particle bed is as well increased, since it must be possible to move it across the reinforcement. The objective was thus to investigate the effect of that distance on print quality and to quantify a maximum allowable distance for an adequate print quality (for the printer setting used) in terms of shape accuracy and concrete strength. Compressive and flexural strength tests as well as geometrical measurements using a 3D scanning method were performed on specimen, printed with varying print nozzle to particle bed distances. It can be stated that for the used SPI print-heads, nozzle-types and parameter settings, the distance between the nozzle and the particle bed should not exceed 50 mm to ensure sufficient print quality in both shape accuracy and mechanical strength.

While the standard model accurately describes data at the electroweak scale without inclusion of gravity, beyond the standard model physics is increasingly intertwined with gravitational phenomena and cosmology. Thus gravity mediated breaking of supersymmetry in supergravity models lead to sparticles masses, which are gravitational in origin, observable at TeV scales and testable at the LHC, and supergravity also provides candidate for dark matter, a possible framework for inflationary models and for models of dark energy. Further, extended supergravity models, and string and D-brane models contain hidden sectors some of which may be feebly coupled to the visible sector resulting in heat exchange between the visible and hidden sectors. Because of the couplings between the sectors both particle physics and cosmology are effected. The above implies that particle physics and cosmology are intrinsically intertwined in the resolution of essentially all of the cosmological phenomena such as dark matter and dark energy and in the resolution of cosmological puzzles such as Hubble tension and EDGES anomaly. Here we give a brief overview of the intertwining and implications for the discovery of sparticles, and the resolution of the cosmological anomalies and identification of dark matter and dark energy as major challenges for the coming decades.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in the rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments of Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reducing surface runoff during rainy season.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

Organometallic drug development is still in its early stage, but recent studies show that organometallics having iron as the central atom have the possibility of becoming good drug candidates because iron is an important micro-nutrient, and it is compatible with many biological systems, including the human body. Being an eco-friendly Lewis acid, iron can accept the lone pair of electrons from imino(sp2)-nitrogen, and the resultant iron-imine complexes with iron as a central atom have the possibility of interacting with several proteins and enzymes in humans. Iron-imine complexes have demonstrated significant potential as anticancer, bactericidal, fungicidal, and other medicinal activities in recent years. This article systematically discusses major synthetic methods and pharmacological potentials of iron-imine complexes having in vitro activity to significantly affect clinical performance from 2016 to date. In a nutshell, this manuscript offers a simplistic view of iron complexes in medicinal inorganic chemistry: for instance, iron is presented as an "eco-friendly non-toxic" metal (as opposed to platinum) that will lead to non-toxic pharmaceuticals. The abundant literature on iron chelators shows that many iron complexes, particularly if redox-active in cells, can be quite cytotoxic, which can be beneficial for future targeted therapies. While we made every effort to include all the related papers, any omission is purely unintentional.

A problem involving the government's inspection of coins in Lower Slobbovia is discussed in the \emph{American Mathematical Monthly}. It is desirable to classify and correct counterfeit coins by utilizing the fewest possible measures. However, previous article only proves the existence of the solution, which does not give a practical solution to the problem. This note provides effective methods to achieve the identification of coiners using dirac delta function and singularity function. Moreover, unit-order construction of continuum mappings and discretization of unique basis vectors with semi-expansion are established in S-base space.

Multiplex genome editing may induce genotoxicity and chromosomal rearrangements due to double-strand DNA breaks at multiple loci simultaneously induced by programmable nucleases, including CRISPR/Cas9. However, recently developed base-editing systems can directly substitute target sequences without double-strand breaks. Thus, the base-editing system is expected to be a safer method for multiplex genome-editing platforms for livestock. Target-AID is a base editing system composed of PmCDA1, a cytidine deaminase from sea lampreys, fused to Cas9 nickase. It can be used to substitute cytosine for thymine in 3-5 base editing windows, 18 bases upstream of the protospacer-adjacent motif site. In the current study, we demonstrated Target-AID-mediated base editing in porcine cells for the first time. We targeted multiple loci in the porcine genome using the Target-AID system and successfully induced target-specific base substitutions with up to 63.15% efficiency. This system can be used for the further production of various genome-engineered pigs.

A random variable X that is base b Benford will not in general be base c Benford when c is not equal to b. This paper builds on two of my earlier papers and is an attempt to cast some light on the issue of base dependence. Following some introductory material, the “Benford spectrum” of a positive random variable is introduced and known analytic results about Benford spectra are summarized. Some standard machinery for a “Benford analysis” is introduced and combined with my method of “seed functions” to yield tools to analyze the base c Benford properties of a base b Benford random variable. Examples are generated by applying these general methods to several families of Benford random variables. Berger and Hill's concept of “base-invariant significant digits” is discussed. Some potential extensions are sketched.

The fluid flow field at the upper airways is highly complex due to the complex structure of the airway. The inhaled particle flow, the air streamline and the interaction of the continuum and discrete phase could significantly affect the transport behaviour of the inhaled particles. A range of analytical, mathematical and computational fluid dynamics (CFD) models analyzed the airflow and particle transport in different idealized and asymmetric airway models. A precise understanding of the continuum and discrete phase interaction in realistic human airways is missing, and this study aims to develop a CFD-DEM model for particle transport in realistic airways. This study uses the CFD model for the continuum phase and the discrete element method (DEM) for the discrete phase. A soft sphere approach is used for the interaction of the discrete phase. Proper validation is performed for particle transport efficiency. The CFD-DEM model analyzed the particle transport in an idealized and realistic airway model, and different methods are used to analyze the transport behaviour. During the particle-particle interaction, a stagnation point and a high-pressure zone are observed at the airway model's carinal angle. The numerical results report higher deposition efficiency (DE) for particle-particle interaction than without interaction. The flow field becomes highly complex with the spring constant values, and higher DE is found for high spring constant values. The spring dashpot friction-dshf method shows higher deposition at the upper part of the airways than other interaction methods. The findings of this study and more case-specific analysis would improve the knowledge of aerosol transport in airways and the health risk assessment of the patient.

Double suction centrifugal pump installed along the Yellow River faces the serious sediment erosion due to the high sediment content which cause the poor operation efficiency of pump unit. The particle motion characteristics and erosion characteristics in the pump under different flow rates and different particle concentrations were numerically simulated based on the particle track model of solid-liquid two-phase flow. The results show that the flow rate has a significant effect on the particle tracks and the erosion caused by the particles in the impeller. The total erosion rate is positively correlated with the flow rate, and increases with the increase of flow rate. The vortex and secondary flow in the impeller have obvious influence on the particle trajectory, which increases the particle concentration at the trailing edge of the pressure surface and intensifies the impact erosion in this area. The particles carried by the vortex intensifies the local erosion. The particle concentration mainly affects the erosion rate, but has little effect on the erosion position. The in-fluence of flow rate on the pump erosion is greater than that of the particle properties. These results provide a reference for optimization of the design of anti-erosion blades of the double-suction pump and regulation-operation of pumping station.

Meshfree particle method, which is always regarded as a pure Lagrangian approach, is easily represented complicated domain topologies, moving boundaries, and multiphase media. Solving acoustic problems with the mesfree particle method forms a branch of the acoustic wave modeling field, namely, particle-based computational acoustics (PCA). The aim of this paper is to improve the accuracy of using the PCA method to solve two-dimensional acoustic problems, and realize the particle representation with a hybrid meshfree and finite-difference time-domain (FDTD) method for acoustic boundary conditions at both the plane and curved surface. As a widely used Lagrangian meshfree method, the smoothed particle hydrodynamics (SPH) based on the support domain and the kernel function has developed rapidly in recent years. The traditional SPH method is easily implements parallel processing and has been applied in sound wave simulation. As a corrective method with higher accuracy than SPH, the acoustic propagation and scattering in the time domain is simulated with the corrective smoothed particle method (CSPM). Moreover, a hybrid meshfree-FDTD boundary treatment technique is utilized to represent different acoustic boundaries in the Lagrangian approach. In this boundary treatment technique, the parameter value of virtual particles is obtained with the FDTD method, which concerns truncation errors based on the Tayler series expansion. Soft, rigid, and Mur’s absorbing boundary conditions are developed to simulate sound waves in finite and infinite domain. Results of modeling acoustic propagation and scattering show that CSPM is accurate and convergence with exact solutions, and different acoustic boundaries are validated to be effective in the computation.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

The present study produced and characterised chitosan, chitosan nanoparticle, chitosan n – benzaldehyde Schiff base, chitosan nanoparticle n – benzaldehyde Schiff base, Fe(III) chitosan n – benzaldehyde Schiff base and Fe(III) chitosan nanoparticle n – benzaldehyde Schiff base for biomedical application as antimicrobial agents. The materials were characterized with Fourier Transform Infrared spectroscopy, X-ray Diffractogram and biologically evaluated using disc diffusion method with three gram-positive bacteria. The FTIR absorption peaks were shifted to a lower wave number than the micro materials from which it was modified. These clearly indicate the linkage between phosphate, ammonium ion, Schiff base and Fe(III) metal. The diffracted peaks of Fe(III) chitosan nanoparticle n – benzaldehyde Schiff base were new peaks at 2θ = 24o and 42o when compare to the peak of Fe(III) chitosan n – benzaldehyde Schiff base of 2θ = 22.5o and 34o. The difference in peak shift were attributed to the ionic bonding of the complexation of Fe(III) with the blending of benzaldehyde to chitosan – Tpp backbone structure. Fe(III) chitosan nanoparticle Schiff base has more antimicrobial activity against same bacteria and fungi tested than Fe(III) chitosan n – benzaldehyde Schiff base, chitosan n – benzaldehyde Schiff base and chitosan. The antimicrobial activities of the synthesised six materials shown that the materials have high activities than the above – mentioned standard drugs.

This study focuses on one of the most famous open problems in mathematics, namely the Collatz conjecture. The Collatz conjecture or 3x + 1 Problem is perhaps today's most enigmatic unsolved mathematical problem. It is named after Lothar Collatz, who rst proposed it in 1937. It may be stated as as follow: Take any positive integer n. If n is even then divide it by 2, else do \triple plus one" and get 3n + 1. The conjecture is that this process will eventually reach the number 1, regardless of which positive integer is chosen initially. In this paper, we present a simple proof for the Collatz conjecture.

A series of novel indole Schiff base derivatives (2a–2t) containing a 1,3,4-thiadiazole scaffold modified with a thioether group were synthesized, and their structures were confirmed using FT-IR, ¹H NMR, ¹³C NMR, andHR-MS. In addition, the antifungal activity of synthesized indole derivatives was investigated against Fusarium graminearum (F. graminearum), Fusarium oxysporum (F. oxysporum), Fusarium moniliforme (F. moniliforme), Curvularia lunata (C. lunata), and Phytophthora parasitica var. nicotiana (P. p. var. nicotianae) using the mycelium growth rate method. Among the synthesized indole derivatives, compound 2j showed the highest inhibition rates of 100%, 95.7%, 89%, and 76.5% at a concentration of 500 μg/mL against F. graminearum, F. oxysporum, F. moniliforme, and P. p. var. nicotianae, respectively. Similarly, compounds 2j and 2q exhibited higher inhibition rates of 81.9% and 83.7% at a concentration of 500 μg/mL against C. lunata. In addition, compound 2j has been recognized as a potential compound for further investigation in the field of fungicides.

Single-stand selective monofunctional uracil DNA glycosylase 1 (SMUG1) works to remove uracil and certain oxidized bases from DNA during base excision repair (BER). This review provides a historical characterization of SMUG1 and 5-hydroxymethyl-2'-deoxyuridine (5-hmdU) one important substrate of this enzyme. Biochemical and structural analyses provide remarkable insight into the mechanism of this glycosylase revealing SMUG1 has a unique helical wedge which influences damage recognition during repair. Rodent studies suggest that, while SMUG1 shares substrate specificity with another uracil glycosylase UNG2, loss of SMUG1 can have unique cellular phenotypes. This review highlights the multiple roles SMUG1 may play in preserving genome stability, and how the loss of SMUG1 activity may promote cancer. Finally, we discuss recent studies indicating SMUG1 has moonlighting functions beyond BER, playing a critical role in RNA processing including the RNA component of telomerase.

Abstract Thyroid diseases have a complex and multifactorial aetiology. Despite the numerous studies on the signals referable to the malignant transition, still remain elusive the molecular mechanisms concerning the role of oxidative stress. Based on its strong oxidative power, H2O2 could be responsible for the high level of oxidative DNA damage observed in cancerous thyroid tissue and hyper-activation of mitogen-activated protein kinase (MAPK), and PI3K/Akt, that mediate ErbB signaling. Increased levels of 8-oxoG DNA adducts have been detected in the early stages of thyroid cancer. These DNA lesions are efficiently recognized and removed by the base excision repair (BER) pathway initiated by 8-oxoG glycosylase1 (OGG1). This study investigated the relationship between the EGFR and OGG1-BER pathways and their mutual regulation following oxidative stress stimulus by H2O2 in human thyrocytes. We clarified the modulation of ErbB receptors and their downstream pathways (PI3K / Akt and MAPK / ERK) under oxidative stress (from H2O2) at the level of gene and protein expression, according to the mechanism defined in a non-pathological cell system, Nthy-ori 3-1. Later, on the basis of the obtained results of gene expression cluster analysis in normal cells, we assessed the dysregulation of the relationships in a model of papillary thyroid cancer with RET/TPC rearrangement (TPC-1). Our observations demonstrated that a H2O2 stress may induce a physiological cross-regulation between ErbB and OGG1-BER pathways in normal thyroid cells (while this is dysregulated in the TPC-1 cells. Gene expression data also delineated that MUTYH gene could play a physiological role in cross-talk between ErbB and BER pathways and this function is instead lost in cancer cells. Overall our data about OGG1 protein expression suggest that the alternative splicing mechanisms may lead to different protein isoforms, physiologically regulated in response to ErbB modulation, and that these could be dysregulated in the progression of thyroid malignancies with RET/TPC rearrangement.

Most human genetic disease arises from point mutations. These genetic diseases can theoretically be corrected by gene therapy but clinic practice is still far from mature. Nearly half of the pathogenic single-nucleotide polymorphisms (SNPs) are caused by G:C>A:T or T:A>C:G base changes. The best current methods to repair these changes are by base editing without footprint using recently developed CRISPR-Cas9 technology by David Liu’s lab. These base editing methods have been confirmed with precision and efficiency in cultured mammalian cells, but it is barely confirmed and the efficiency is still very low. Animal models are important in dissecting pathogenic mechanism for human genetic diseases and efficacy testing of base correction in vivo. Cytidine base editor BE4 is a newly developed version of cytidine base editing system that converts cytidine (C) to uridine (U) in cultured mammalian cells but has not been proven in vivo. In this study, we have tested this system in cells to inactivate GFP gene and in mice by introducing single-base substitution that leads to a stop codon in tyrosinase gene. High percentage albino coat-colored mice were obtained from black coat-colored donor zygotes after pronuclei microinjection. Sequencing results showed that expected base changes were obtained with high precision and efficiency (56.25%). There are no off-targeting events identified in predicted off-target sites. Results confirm BE4 system can work in vivo with high precision and efficacy, and has great potentials in clinic to repair human genetic mutations.

in this article, an ultra-wideband traveling wave antenna with antipodal topology is proposed. The proposed design is realized on an economical substrate with minimum thickness. The proposed design offers an ultra-wide bandwidth of 26 to 40 GHz, translating to 42%. The dimensions of the antenna are 20mm x10mm x 0.5mm indicating an electrically compact structure. The proposed antenna offers high front to back ratio of at least 10dB across the bandwidth of operation. The forward gain of the antenna varies from 4 to 7dBi in the afore-mentioned band. The pattern integrity is maintained throughout the band. The antenna is fabricated using the commercial photolithography process. A mutli-step topology of the antennas is also proposed for wide angular coverage. The coverage is greater than 150º with mutual coupling less than 25dB. These performance metrics is achieved with a very small footprint. Simulated and experimental results are presented in this paper.

Abstract. Leiomyoma is a benign tumour of smooth muscle cells classified into three groups: solid leiomyoma, angioleiomyoma and leiomyoblastoma. Angioleiomyoma arises from the tunica media of veins and arteries of vascular smooth muscle.Nasal cavity, paranasal sinus and oral cavity are the most frequent locations in Head and Neck region. Here we present the case of a tongue base angioleiomyoma with an emphasis on clinical data, pathologic findings and surgical approach. The patient complained about a one-month of globus sensation, dysphagia and hemoptysis without other systemic symptoms. Laryngoscopy revealed the presence of a 2 cm solitary submucosal mass located on the left tongue base covered with normal mucosa. The patient underwent direct laryngoscopy to perform a biopsy for the purpose of achieving the conclusive diagnosis. Treatment options were discussed, included surgical resection. Transoral robot-assisted resection was performed without complications. Clearly the description of our case does not want to have a purpose in terms of indications but wants to describe the possibility of considering TORS in the case of benign tumours of the tongue base, especially in cases like this where a standard technique can difficulty be achieved. Current literature review was provided and discussed.

In this paper, a circularly polarized broadband slot antenna is designed for base station applications. The antenna is built on a square-shaped FR4 Epoxy substrate that measures 60mm in length and 1mm in height with a relative permittivity of 4.4. The ground plane has a recessed slot, and the feeding mechanism employs an offset microstrip line. The slot enables circular polarization and optimal impedance matching, which are enhanced further by offset feeding and the addition of stubs to create a composite-shaped patch. With an impedance bandwidth of 106% (1.28 GHz-4.16 GHz) and an axial ratio bandwidth of 69% (1.71 GHz-3.51 GHz), the CP broadband slot antenna effectively covers popular mobile communication bands such as GSM 1800, GSM 1900, 3G/LTE 2100, 3G/LTE 2300, 4G/LTE 2500, and 2.4 GHz Wi-Fi bands. The maximum gain is simulated to be 3.5 dB.

Plasma-activated water (PAW) is an emerging and promising green technology in the agriculture sector during recent years. The aim of this study was to examine the influence of the spraying of PAW and amino acid fertilizer concentrations on the physiological, biochemical and phytochemical characteristics of German chamomile varieties under field conditions. Method: The experiment was performed during 2020–2021 as a factorial using a randomized complete block design with three replications, in an arid and warm region. The factors contained five fertilizer levels (0 (control), 1, 2, 3 ml·L−1 amino acid and PAW) and three German chamomile cultivars Bona, Bodegold, Lianka). Physiological, biochemical and phytochemical traits such as plant height, fresh and dried flower weight, chlorophyll a, b, carotenoids, CHN elements, C:N ratio, total protein, amino acid profile, essential oil yield, apigenin content and major secondary metabolites were examined. Results: The ANOVA indicated that the impact of the cultivar and fertilizer was significant on all physiological, biochemical and phytochemical studied parameters. The amino acid fertilizer and PAW enhanced physiological features, hydrogen, C:N ratio, essential oil yield, apigenin content and main phytochemical compositions like chamazulene and α-bisabolol, but it had no incremental effect on the carbon, nitrogen, and total protein percentage. Conclusion: Findings revealed that the application of foliar amino acid fertilizer and PAW treatments improves physiological, biochemical and phytochemical parameters in German chamomile cultivars under field conditions.

Quantitative measurements of performance parameters has the potential to increase consistency and enhance performance of the surfaces as well as to contribute to the safety of horses and riders. This study investigates how factors known to influence the performance of the surface, incorpo-ration of a drainage package, control of the moisture control, and introduction of a geotextile reinforcement, affect quantitative measurements of arena materials. The measurements are made by using affordable lightweight testing tools which are readily available or easily constructed. Sixteen boxes with arena materials at a consistent depth were tested with the Going Stick (GS), both penetration resistance and shear, the impact test device (ITD), and the rotational peak shear device (RPS). Volumetric moisture content (VMC %) was also tested with time-domain reflectometry (TDR). Results obtained using GS, RPS, ITD, and TDR indicate that the presence of the drainage package, moisture content, and geotextile addition were detected. Alterations due to combinations of treatments could also be detected by GS, ITD, and TDR. While the testing showed some limi-tations of these devices, the potential exists to utilize them for quality control of new installations as well as for the monitoring of maintenance of the surfaces.

Global population is predicted to approach 10 billion by 2050, an increase of over 2 billion from today. To meet the demands of growing, geographically and socio-economically diversified nations, we need to diversity and expand agricultural production. This expansion of agricultural productivity will need to occur under increasing biotic, and environmental constraints driven by climate change. Clustered regularly interspaced short palindromic repeats-site directed nucleases (CRISPR-SDN) and similar genome editing technologies will likely be key enablers to meet future agricultural needs. While the application of CRISPR-Cas9 mediated genome editing has led the way, the use of CRISPR-Cas12a is also increasing significantly for genome engineering of plants. The popularity of the CRISPR-Cas12a, the type V (class-II) system, is gaining momentum because of its versatility and simplified features. These include the use of a small guide RNA devoid of trans-activating crispr RNA (tracrRNA), targeting of T-rich regions of the genome where Cas9 is not suitable for use, RNA processing capability facilitating simpler multiplexing, and its ability to generate double strand breaks (DSB) with staggered ends. Many monocot and dicot species have been successfully edited using this Cas12a system and further research is ongoing to improve its efficiency in plants, including improving the temperature stability of the Cas12a enzyme, identifying new variants of Cas12a or synthetically producing Cas12a with flexible PAM sequences. In this review we provide a comparative survey of CRISPR-Cas12a and Cas9, and provide a perspective on applications of CRISPR-Cas12 in agriculture.

The article describes facile one-pot, hi-yielding reactions to synthesize substituted 3,4-dimethyl-1H-pyrrole-2-carboxamide (3a–m) and carbohydrazide analogues (5a–l) as potential antifungal and antimicrobial agents. The structural integrity and purity of the synthesized compounds were assigned based on appropriate spectroscopic techniques. Synthesized compounds were assessed in vitro for antifungal and antibacterial activity. The compound 5h, 5i and 5j were found to be the most potent against A. fumigatus, with MIC value of 0.031 mg/mL. The compound 5f bearing a 2,6-dichloro group on the phenyl ring was found to be the most active broad spectrum antibacterial agent with MIC value of 0.039 mg/mL. The mode of action of the most promising antifungal compounds (one representative from each series; 3j and 5h) was established by their molecular docking to the active site of sterol 14α-demethylase. Molecular docking studies revealed a highly spontaneous binding ability of the tested compounds in the access channel away from catalytic heme iron of the enzyme, which suggested that the tested compounds inhibit this enzyme and would avoid heme iron related deleterious side effects observed with existing antifungal compounds.

A new approach was presented in this study to simulate a stable atom along with subatomic particles in it. Subatomic particles in an atom are treated as conventional particles, exhibiting attraction and repulsion between them, giving a stable atom simulation. This new approach leads to developing new potentials for subatomic particles to simulate a stable atom. Subatomic particle dynamics (SPD) simulations were developed for within-atom simulations that give a stable atom structure for infinite time and provide many insights into electron trajectories and atom properties like energies and radius of the atom. The effect of protons and neutrons movement in the nucleus on electron trajectories was captured in SPD. Hydrogen and Carbon atom SPD were reported in this study. The Pilot-wave theory was implemented in this study to simulate the wave nature of subatomic particles in an atom. Electrons motion was guided by the interference pattern produced by the electron’s aether medium waves in SPD. SPD was implemented on molecules, resulting in a stable molecular structure giving insights into electron trajectories shared by multiple atoms.

In this work, we propose a variation of the cellular particle swarm optimization algorithm with differential evolution hybridization (CPSO-DE), to include constrained optimization in it, named Ts-CPD. It is implemented as a kernel of electronic design automation (EDA) tool capable of sizing circuit components considering a single-objective design with restrictions and constraints. The aim is to improve the optimization solutions in the sizing of analog circuits. To evaluate our proposal’s performance, we present the design of three analog circuits: a deferential amplifier, a two-stage operational amplifier, and a folded cascode operational transconductance amplifier. Numerical simulation results indicate that Ts-CPD can find better solutions, in terms of the design objective and the accomplishment of constraints, than those reported in previous works.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

Magnetic Particle Imaging (MPI) is a new imaging modality that sensitively and specifically detects superparamagnetic iron oxide nanoparticles (SPIONs). Many labs have been developing cellular magnetic resonance imaging (MRI) tools using both SPIONs and fluorine-19 (19F)-based contrast agents for numerous important applications, including tracking of immune and stem cells used for cellular therapies. SPION-based MRI cell tracking has very high sensitivity, but low specificity. SPIONs produce negative contrast in MRI, or signal voids. SPIO is not directly detected by MRI, but indirectly through its relaxation effects on protons, therefore, it is not possible to reliably quantify the local tissue concentration of SPION particles and cell number cannot be determined. 19F based cell tracking uses perfluorocarbons (PFC) to label cells. The number of 19F atoms can be directly measured from 19F MR images and related to cell number. 19F MRI has high specificity, but low sensitivity. MPI cell tracking displays great potential for overcoming the challenges of MRI-based cell tracking allowing for both high cellular sensitivity and high specificity and quantification of SPIO labeled cell number. In this paper we describe nanoparticle and MPI system factors that influence MPI sensitivity and resolution, quantification methods and give our perspective on testing and applying MPI for cell tracking.

Measurements of optical properties have been used for decades to study particle distributions in the ocean. They have been found useful to constrain suspended mass concentration as well as particle-related properties such as size, composition, packing (particle porosity or density) and settling velocity. Optical properties, however, provide measurements that are biased, as certain particles (based on size, composition, shape or packing) contribute to a specific property more than others. Here we study this issue both theoretically as well as by contrasting different optical properties collected simultaneously in a bottom boundary layer, to highlight the utility of such measurements as well as the biases we are likely to encounter using different optical properties to study suspended particles. In particular, we investigate the possibility to infer settling velocity from vertical profiles of optical measurements, finding that the effects of aggregation dynamics can seldom be ignored.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

The production of anatase titanium dioxide particles plays a crucial role in the sulfate process used for manufacturing white pigment. A key factor in improving the quality of white pigments is enhancing the thermal mixing process within the precipitation tank. This improvement ensures the uniform dispersion of seed particles instead of their agglomeration, leading to the formation of particles with uniform sizes. The objective of this study was to enhance three-phase CFD simulations involving the mixing process of H₂SO₄ solution, steam as a gas phase, and solid seed particles. By analyzing the trajectories of the seed particles using CFD, the optimal injection position for the seed particles within the mixing process was determined. Subsequently, lab scale test and real field test were conducted based on the insights gained from the CFD simulations. The particle size distribution of two different types of seed inlets was analyzed and compared using Transmission Electron Microscopy (TEM). The findings of this study demonstrate that the developed multi-phase CFD simulation can be effectively utilized to enhance the precipitation process for the production of anatase titanium dioxide particles.

The growth of state transfers to equalize regional development disparities affects the stability of the state's financial system. The research aims at determining how the mechanism of horizontal alignment of fiscal imbalances between local budgets affects the stability of financial system of Ukraine. To assess the asymmetry of the alignment formula, we use a quasi-experimental strategy of analyzing potential scenarios, we calculate base grants (for recipient municipalities) and reverse grants (for donor municipalities) for 1439 municipalities in Ukraine. Then we conduct counterfactual experiments, where we change the calculation subject, the number of budgets in calculation and the calculation period. Under different calculation scenarios, we determine whether the alignment mechanism has positive or negative affect on the stability of the public finance system based on the criterion of non-accumulation of budgetary debt. We establish that the current system of horizontal fiscal alignment in Ukraine overstates the fiscal capacity of communities, artificially inflating the indicators of the performance of the imbalance alignment system reform and distorting the overall picture of public finance stability. The alignment system, designed to mitigate unevenness in socio-economic community development, actually exacerbates it. The mechanism for calculating community fiscal capacity, which underlies horizontal financial alignment, requires an improved approach to determining the calculation subject and further reform.

The most important step for the installation of a wind farm is to know the wind regime in the region, since an error in estimating this wind speed causes an error proportional to the cube of power, resulting in financial losses for investors. Therefore, knowing the methods used for predicting wind speed becomes important and the knowledge of how research and studies in this area are going helps map the subject and outline strategies for developing research in strategic areas. For this purpose, the Scopus database was used considering some keywords, such as ("forecast" OR "prevision") AND "wind" AND ("turbine" OR "power" OR "energy" or "velocity" or "speed"), considering the period since 2019, and analyzing the data of the documents found using the Bibliometrix package. With the results found, it was possible to map researchers, institutions that are developing work in this area, in addition to the most cited articles, among other aspects analyzed.

In recent years, drones have been used in a wide range of fields such as agriculture, transportation of goods, and security. Drones equipped with communication facilities are expected to play an active role as base stations in areas where ground base stations are unavailable, such as disaster areas. In addition, asynchronous operation is being considered for local 5G in order to support all kinds of use cases. In asynchronous operation, cross-link interference between base stations is an issue. This paper attempts to reduce the interference caused by the drone network by introducing circularly polarized antennas. Numerical analyses are conducted to validate the effectiveness of the proposed system, where SIRs (Signal-to-Interference Ratio) are shown to be improved significantly as the numerical evaluation results.

Surgical ciliated cysts occur primarily in the maxilla after radical maxillary sinus surgery. We report a first case of a surgical ciliated cyst that developed in the infratemporal fossa 25 years after the patient sustained severe facial trauma. The patient complained of mandibular pain and limited mouth opening. The patient’s condition was completely resolved 5 months after marsupialization via Le Fort I osteotomy. Surgical morbidities can be minimized by proper diagnosis and less invasive surgery.

In 2018, the author identified a previously unknown/unreported association between dexrazoxane and poly(ADP-ribose) (PAR). Interestingly, PAR is a close structural analogue of the polyadenine nucleotide polymer, polyadenosine monophosphate (poly(A)). In this report, subsequent in silico modelling of the interaction between dexrazoxane and poly(A) reveals some notable differences from the previously reported interaction between dexrazoxane and PAR. Significantly, the supramolecular self-assembly of dexrazoxane and poly(A) is distinguished by vertically-orientated nonelectrostatic forces comparable to the stabilizing interactions between stacked bases within DNA. Notably, the vertical separation of 3.4 Å between each stack is consistent with solvent entropy as a dominant driving force in stabilising the interaction. Additionally, concomitant conformational analysis by the author reveals the existence of low energy planar conformers of dexrazoxane. This analysis enables an explanation for the considerable discrepancies and conflicts that exist within the reported pharmacokinetic data for dexrazoxane. Exploring the significance of the interaction between dexrazoxane and poly(A), the author illustrates that survival, translation and replication of the severe acute respiratory syndrome virus 2 (SARS-CoV-2) is absolutely dependent upon the mature and unhindered poly(A) tail of the SARS-CoV-2 genome. The proposition herein, that dexrazoxane, as a chameleonic agent sequesters the poly(A) tail of the SARS-CoV-2 genome by the catalysis of a supramolecular hybrid assembly establishes SARS-CoV-2 infected cells as deep compartments for the accumulation of dexrazoxane. Taken together, dexrazoxane or its demethylated analogue, represent a novel treatment to kill the SARS-CoV-2 virus by irreversible destabilization of the SARS-CoV-2 poly(A) tail.

Suzuki cross-coupling reaction has developed one of the furthermost effectual approaches for the synthesis of biaryls or substituted aromatic moieties from aryl halides and arylboronic acids with a palladium-catalyst in the past two era’s. Herein, Pd-free layered double hydroxide containing nickel catalysts were prepared by co-precipitation method under ultrasonic irradiation and N2 atmosphere with different molar ratios of Ni: Mg: Al and coded as (1NiLDHs-Dr), (1.5NiLDHs-Dr) and (2NiLDHs-Dr). A series of reduced catalysts under 5%H2/N2 at different temperatures were coded as 1NiLDHs-R200, 1.5NiLDHs-R200 and 2NiLDHs-R200. As-synthesized 2NiLDHs-Dr was the superlative catalyst when coupling different aryl halides with different boronic acids derivatives. Deep investigation of all catalysts was done using different techniques such as inductively coupled plasma optical emission spectroscopy (ICP-OES), x-ray photoelectron spectroscopy (XPS), powder x-ray diffraction (XRD), thermogravimetric analyses (TGA), Fourier transfer infrared (FTIR), scanning electron microscope (SEM) connected with energy dispersive x-ray (EDX) and N2-physisorption at -196 ℃. The results attained verified that ɑ-Ni(OH)2 was fashioned for 2NiLDHs-Dr catalyst and the enclosure of nickel ions in the cationic sheet of layered structure were responsible for the fascinating catalytic efficacy rather than the basic nature of material. The Ni-containing LDHs catalysts encourage forthcoming studies in Pd-free catalyzed C-C coupling reactions.

5-(4-aminophenyl )-2-amino -1,3,4-thiadiazole was prepared by reaction of Thiosemicarbazide with 4-amino benzoic acid under reflux condition for 7 hours. The compound which has been synthesized successfully was subjected to addition reaction with 4-(Dimethylamino) benzaldehyde under reflux condition for 6 hours to synthesize Schiff bases. These compounds was characterized by using FTIR) and evaluated for their anticancer activity. The effect of (1, 3, 4-thiadiazole derivative) on the activity of malignant cells was studied by using different types of cell lines [Breast cancer, and human prostate cancer]. And was used the Electron microscope to show that the effect of the derivative on the cancer cells before and after 3 days of the injection time. It was found that the Schiff base of thiadiazole-1,3,4-(Dimethylamino)benzylidineamino]- [4-2-phenyl]amino was effective in reducing the size and density of malignant cells. That of 46.7 while in breast ) 145(DUprostate for growth inhibition produce of equal 85.9 µg/ml.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

Piezoelectric nanotransducers may offer key advantages in comparison with conventional piezoelectrics, including more choices for types of mechanical input, positions of the contacts, dimensionalities and shapes. However, since piezo-semiconductive nanostructures are generally much easier to fabricate and integrate into functional systems than insulating materials, modeling becomes significantly more intricate and the effects of free charges have been considered only in a few studies. The available reports are complicated by the absence of proper nomenclature and figures of merit. Besides, some analyses are incomplete. For instance, the local piezopotential and free charges within axially strained conical piezo-semiconductive nanowires have only been systematically investigated for very low doping (1016 cm-3) and under compression. Here we give the definitions for the enhancement, depletion, base and tip piezopotentials, their characteristic lengths and both the tip-to-base and the depletion-to-enhancement piezopotential-ratios. As an example, we use these definitions for analyzing the local piezopotential and free charges in n-type ZnO truncated conical nanostructures with different doping levels (intrinsic, 1016 cm-3, 1017 cm-3) for both axial compression and traction. The definitions and concepts presented here may offer insight for designing high performance piezosemiconductive nanotransducers.

Hypoxia, associated with abnormal vessel growth, is a characteristic feature of many solid tumors that increases their metastatic potential and resistance to radiotherapy. Carbon ion radiation therapy, alone or in combination with other treatments, is one of the most promising treatments for hypoxic tumors because the oxygen enhancement ratio decreases with increasing particle LET. Nevertheless, the current clinical practice does not yet fully benefit from using carbon ions for tackling hypoxia. Here we give an overview of the existing experimental and clinical evidence supporting the efficacy of C-ion radiotherapy in overcoming hypoxia-induced radioresistance, followed by a discussion of the strategies proposed to enhance it, including different approaches to maximize the LET in the tumors.

Polyaniline or PANI is a conductive polymer (CPs) with flexibility in turning into conducting properties. The drawback is mainly in terms of limited mechanical properties improvement which attracted the interest in fabrication of PANI with other polymeric materials. PANI-PVL composites film was synthesized and fabricated in this work with chronological steps according to the objectives aligned in two different phases. The first phase determines the optimum parameters to synthesize nanosized PANI. The ideal initial molar ratio, r was 1, stirring speed of 600 rpm, purified by filtration, synthesis temperature of 25 oC, washed by dopant acid, acetone and distilled water. The usage of non-ionic surfactant, Triton X-100 (TX100) with 0.1 % concentration favours the formation of smaller particle size of PANI and good dispersibility compared to the usage of anionic sodium dodecyl sulphate (SDS). The synthesis of PANI in nanosized dimension has the potential to be applied for antimicrobial applications such as gloves and antimicrobial coating of frequent contact points in the near future.

We investigate the Friedmann–Lemaitre–Robertson–Walker cosmological models within the framework of Rastall gravity incorporating particle creation. The modified field equations for Rastall gravity are derived and exact solutions are obtained under various choices of scale factors. The qualitative behaviour of our solutions depends on the Rastall coupling parameter ψ=kλ. Following the literature, we have restricted the Rastall coupling parameter ψ(k=1) to the range −0.0001 < ψ < 0.0007 at 68% CL from CMB+BAO data. Further, we have discussed the distinct physical behaviour of the derived models in detail.

We define a spinor-Minkowski metric for SL(4,C). It is not a trivial generalization of the SL(2,C) metric and it involves the Minkowskian one. We define 4x4 version of the Pauli matrices and eight 4-component associated generalized eigenvectors that can be regarded as undotted covariant spinors. The 4-component spinors can be grouped into four categories. Each category transforms in its own way. The outer products of pairwise combinations of 4-component spinors can be associated with 4-vectors. Including the dotted covariant, undotted and dotted contravariant forms totally we have sixteen pairs of spinors. Eight of them live in the conjugate space which has no countepart in SL(2,C).

During the last decade, new unusual physical phenomena have been discovered in studying the optics of dielectric mesoscale particles of an arbitrary three-dimensional shape with the Mie size parameter near 10 (q ~ 10). The paper provides a brief overview of these phenomena from optics to terahertz, plasmonic and acoustic ranges. The different particle configurations (isolated, regular or Janus) are discussed, and the possible applications of such mesoscale structures are briefly reviewed herein in relation to the field enhancement, nanoparticle manipulation and super-resolution imaging. The number of interesting applications indicates to a new promising scientific direction emerged in optics, terahertz and acoustic ranges, and plasmonics. In this paper we present the authors' view of these problems.

In this letter, instead of choosing the Einstein Rosen bridge between two black holes as in ER=EPR, we consider a wormhole between a black hole and a closed edge of the wormhole. We assume that information in a black hole travels through a wormhole, turns to mass (dark matter) in the closed region. This study is in contradiction with the existence of the white hole in our Universe. We replace the notion of the white hole with the massive closed region. We prove the metric of the closed region by the Hopf fibration, this new metric generalizes the $AdS_{5}$\ metric.

In this paper, we present a technique to unify the Reissner–Nordstr¨om metric and the Kerr–Newman metric. We construct a specifific model and calculate the entanglement entropy of black horizon. We are interested in the entangled particle and antiparticle spinning on the black hole horizon. The two Reissner-Nordstr¨om horizons r±, are the results of the rotation of several entangled particle-antiparticle on the real horizon. The energy absorbed by a black hole is transformed into a kinetic energy of the entangled particle-antiparticles. This study provides a new type of black hole metric. We show that the rotation of an entangled system of a particle and an antiparticle can create a extremal black hole. We also explore some of the implications of this point of view for the black hole entanglement.

This study analyzes the correlation between the lifetime and the rest energy of the unstable particle states with a lifetime greater than the zeptosecond (10⁻²¹ s), using data available from the Particle Data Group. This set of states seems to be divided into three groups, in each of which the two quantities can be correlated through a remarkably accurate power law. Although this fact does not represent anything new compared to the predictions of the Standard Model, it nevertheless reveals an unexpected order structure in the set of particle decays, emerging from such predictions.

Both macro and microprojectiles (e.g., interplanetary, interstellar and even intergalactic material) are seen as important vehicles for the exchange of potential (bio)material within our solar system as well as between stellar systems in our Galaxy. Accordingly, this requires estimates of the impact probabilities for different source populations of projectiles, including for intergalactic meteor particles which have received relatively little attention since considered as rare events (discrete occurrences that are statistically improbable due to their very infrequent appearance). We employ the simple but comprehensive model of intergalactic microprojectile capture by the gravity of exoplanets which enables us to estimate the map of collisional probabilities for an available sample of exoplanets in habitable zones around host stars. The model includes a dynamical description of the capture adopted from Mautner model of interstellar exchange of microparticles and changed for our purposes. We use statistical and information metrics to calculate probability map of intergalactic meteorite particle capture. Moreover, by calculating the entropy index map we estimate the concentration of these rare events. We further adopted a model from immigration theory, to show that the time dependent distribution of single molecule immigration of material indicates high survivability of the immigrated material taking into account birth and death processes on our planet. At present immigration of material can not be observationally constrained but it seems reasonable to think that it will be possible in the near future, and to use it along other proposed parameters for life sustainability on some planet.

Current numerical methods for simulating biophysical processes in aquatic environments are typically constructed in a grid-based Eulerian framework or as an individual-based model in a particle-based Lagrangian framework. Often, the biogeochemical processes and physical (hydrodynamic) processes occur at different time and space scales, and changes in biological processes do not affect the hydrodynamic conditions. Therefore, it is possible to develop an alternative strategy to grid-based approaches for linking hydrodynamic and biogeochemical models that can significantly improve computational efficiency for this type of linked biophysical model. In this work, we utilize a new technique which links hydrodynamic effects and biological processes through a property-carrying particle model (PCPM) in a Lagrangian/Eulerian framework. The model is tested in idealized cases and its utility is demonstrated in a practical application to Sandusky Bay. Results show the integration of Lagrangian and Eulerian approaches allows for a natural coupling of mass transport (represented by particle movements and random walk) and biological processes in water columns which is described by a nutrient-phytoplankton-zooplankton-detritus (NPZD) biological model. This method is far more efficient than traditional tracer based Eulerian biophysical models for 3-D simulation, particularly for a large domain and/or ensemble simulations.

Transport of hydrophobic drugs in the human body exhibits complications due to the low solubility of these compounds. With the purpose of enhancing the bioavailability and biodistribution of such drugs, recent studies have reported the use of amphiphilic molecules, such as phospholipids, for synthesis of nanoparticles or nanocapsules. Given that phospholipids can self–assemble in liposomes or micellar structures, they are ideal candidates to function as vehicles of hydrophobic molecules. In this work, we report mesoscopic simulations of nanoliposomes, constituted by lecithin and coated with a shell of chitosan. The stability of such structure and the efficiency of encapsulation of capsaicin, as well as the internal and superficial distribution of capsaicin and chitosan inside the nanoliposome were analyzed. The characterization of the system was carried out through density maps and the potentials of mean force for the lecithin–capsaicin, lecithin–chitosan and capsaicin–chitosan interactions. The results of these simulations show that chitosan is deposited on the surface of the nanoliposome, as has been reported in some experimental works. It was also observed that a nanoliposome of approximately 18 nm in diameter is stable during the simulation. The deposition behavior was found to be influenced by pattern of N-acetylation of chitosan.

Pharmaceutical aerosols play a key role in the treatment of lung disorders, but also systemic diseases, due to their ability to target specific areas of the respiratory system (RS). This article focuses on identifying and clarifying the influence of various factors involved in the generation of aerosol micro- and nanoparticles on their regional distribution and deposition in the RS. Attention is given to the importance of process parameters during aerosolization of liquids or powders and the role of aerosol flow dynamics in RS. The interaction of deposited particles with the fluid environment of the lung is also pointed out as an important step in the mass transfer of the drug to the RS surface. The analysis presented highlights the technical aspects of preparing the precursors to ensure that the properties of the aerosol are suitable for a given therapeutic target. Analyzing existing technical limitations, several potential strategies for enhancing the efficiency of targeted therapeutic delivery to or through the respiratory system are identified and presented, including the use of smart inhaling devices incorporating AI algorithms.

NUSES is a planned space mission aiming to test innovative observational and technological approaches related to the study of low-energy cosmic rays, gamma rays and high-energy astrophysical neutrinos. Two scientific payloads will be hosted onboard the NUSES space mission: Terzina and Zirè. Terzina will be an optical telescope readout by SiPM arrays, for the detection and study of Cerenkov light emitted by Extensive Air Showers generated by high-energy cosmic rays and neutrinos in the atmosphere. Zirè will focus on the detection of protons and electrons up to a few hundred MeV and to 0.1-10 MeV photons and will include the Low Energy Module (LEM). The LEM will be a particle spectrometer devoted to the observation of fluxes of low-energy electrons in the 0.1-7 MeV range and protons in the 3-50 MeV range along the Low Earth Orbit (LEO) followed by the hosting platform. The detection of Particle Bursts (PBs) in this Physics channel of interest could give new insight into the understanding of complex phenomena such as eventual correlations between seismic events or volcanic activity with the collective motion of particles in the plasma populating van Allen belts. With its compact sizes and limited acceptance, the LEM will allow the exploration of hostile environments such as the South Atlantic Anomaly (SAA) and the inner van Allen belt, in which are expected electron fluxes of the order of 106−7 cm−2 sr−1 s−1. Concerning the vast literature of space-based particle spectrometers, the innovative aspect of the LEM resides in its compactness, within 10x10x10 cm3, and in its “active collimation” approach dealing with the problem of multiple scattering at these very low energies. In this work, the geometry of the detector, its detection concept, its operation modes and the hardware adopted will be presented. Some preliminary results from the Monte Carlo simulation (Geant4) will be shown.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

Layered double hydroxides (LDHs) have emerged as promising catalysts for various acid-base catalytic reactions. Due to their unique structure and regulatable dual acid-base properties, they offer more environmentally friendly and sustainable alternatives to traditional liquid acid and base catalysts. This study introduces the structural composition, preparation methods, and acid-base catalytic properties of LDHs-based catalysts. Recent application progress of LDHs and rehydrated LDHs, LDHs-based metal nanocatalysts, and LDHs-based mixed metal oxide catalysts used as solid acid-base catalysts in acid-base green catalytic conversion is reviewed. The challenges and prospects of LDHs-based catalysts as green and sustainable catalysts are summarized and proposed.

Platinum group metals (PGMs) high-grade ore tonnage from Merensky reef keeps on depreciating forcing the metallurgical industry to explore beneficiating PGMs from upper group 2 (UG2) ore which has up to 60% content of chromite and from secondary sources. The PGMs are naturally associated with base metal sulphides and the efficacy of the PGMs extraction processes is dependent on the processing of PGMs-bearing base metal sulphides. These processes include concentrating PGMs-bearing base metal sulphides through flotation, oxidation, etc. prior the metal extraction processes. The evolving mineralogy of PGMs ores has necessitated the use of multiple reagents to enhance the efficiency of the concentration process. This has led to an increased amount of inor-ganic chemicals disposal to the environment and the processing of PGMs to be less economic. Bio-technology has been investigated as a potential low cost, ecologically safe substitute for many current minerals processing methods. The metabolites produced by microorganisms have been used for many years with great success in the leaching and flotation of metals from medium and low-grade sulphide minerals. The possible application of microorganism mainly Acidithiobacillus ferrooxidans (A. ferrooxidans) in the metallurgical processing of PGMs-bearing base metal sulphides is systematically reviewed in this paper. The main emphasis is on the use of A. ferrooxidans in bio-oxidation and bioleaching, as well as their potential to substitute inorganic reagents in the flo-tation of PGMs-bearing base metal sulphides from primary and secondary sources

The ecological background condition of the semi-arid steppe region (SASR) is extremely fragile. It is recognized that the development of coal and electricity power is a kind of strong human interference behavior for regional landscape ecology. Landscape ecological classification (LEC) is the premise of landscape ecology research of the mining area. The current research on the SASR and grassland LEC of coal-power base is relatively less, but still remains uncertainty concerning how to stratify and classify urban mining landscapes into units of ecological significance at spatial scales appropriate for management. This study is based on hierarchy theory, scale theory, landscape process, the patch-corridor-matrix model, the network, the theory of multiple planning integration and the principle of remote sensing. According to the comprehensive principle, principles of the combining of structure and function, principle of the combining human-ominated and natural landscape, principle of emphasis, and principle of combining qualitative analysis with quantitative research of LEC in large-scale coal-power base(LSCPB). On the basis of occurrence method land classification, fully consider the ecological attributes of the land, integration pattern, processes and function theory of the landscape ecology, the LEC system of the LSCPB in the SASR has been constructed by using top-down decomposition classification method. Empirical research of the Victory and Mindong No.1 mining areas of Shenhua Group shows that the classification system constructed in this paper can meet the requirements of LEC and fully reflect the status of landscape ecology of LSCPB in SASR. This study can provide theoretical guidance for the landscape ecology of LSCPB, while also supporting a theoretical reference for the LEC research.

A series of MgAl-layered double hydroxide (MgAl-HT), the calcined form at 500^oC (MgAlO_x) and the re-hydrated one at 25^oC (MgAl-HT-RH) were synthesized. Physicochemical properties of the catalysts were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM). Surface area of the as-synthesized, calcined and re-hydrated catalysts was determined by N₂ physisorption at -196^oC. CO₂-teperature programmed desorption (CO₂-TPD) was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1-15) were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90^oC in liquid phase, or under microwave irradiation method. The mesoporous structure and basic nature of re-hydrated solid catalyst were responsible for their superior catalytic efficiency. The robust nature was determined by using the same catalyst for five times, where the product % yield was almost unchanged significantly.

The determination of the specific surface free energy, specific properties and Lewis’s acid base of solid materials is of capital importance in many industrial processes such as adhesion, coatings, two dimensional films and adsorption phenomena. (1) Background: The physicochemical properties of many solid particles were characterized during the last forty years by using the retention time of injected well-known molecules into chromatographic column containing the solid substrates to be characterized. The obtained net retention time of the solvents adsorbed on the solid allowing the determination of the net retention volume directly correlated to the specific surface variables, dispersive, polar and acid-base properties. (2) Methods: Many chromatographic methods were used to quantify the values of the different specific surface variables of the solids. However, one found a large deviation between the different results. In this paper, one proposed a new method that quantify the specific free energy of adsorption as well as the Lewis’s acid-base constants of many solid surfaces. (3) Results: The new applied method allowed us to obtain the specific enthalpy and entropy of adsorption of polar model organic molecules on several solid substrates such as silica, alumina, MgO, ZnO, Zn, TiO2 and carbon fibers. (4) Conclusions: our new method based on the separation between the dispersive and polar free surface energy allowed to better characterize the solid materials.

Single-particle inductively coupled plasma mass spectrometry (spICP-MS) has been used for particle size measurement of diverse types of individual nanoparticles and micrometer-sized carbon-based particles, such as microplastics. However, its applicability to the measurement of micrometer-sized non-carbon-based particles such as silica (SiO2) is unclear. In this study, the applicability of spICP-MS to particle size measurement of non-porous/mesoporous SiO2 micro-spheres with a nominal diameter of 5.0 µm or smaller was investigated. Particle sizes of these microspheres were measured using both spICP-MS based on a conventional calibration approach using an ion standard solution and scanning electron microscopy (SEM) as a reference technique and the results were compared. The particle size distributions obtained using both techniques were in agreement within analytical uncertainty. The applicability of this technique to the detection of metal-containing protein-binding mesoporous SiO2 microspheres was also investigated. Bound iron (Fe)-containing proteins (i.e., lactoferrin and transferrin) of mesoporous SiO2 microspheres were detected using Fe as a presence marker for the proteins. Thus, spICP-MS is applicable to the particle size measurement of large-sized and non-porous/mesoporous SiO2 microspheres; it has considerable potential for element-based detection and qualification of bound proteins of mes-oporous SiO2 microspheres in a variety of applications.

Based on collected power generation data associated with solar irradiance, PV system conversion efficiency and cell temperature, an hourly solar PV power estimation model by a parallel artificial neural network (ANN) and particle swarm optimization (PSO) algorithm is proposed. Weight matrices related to different seasons and geographic areas for estimation power generations have been trained by real measured operation data. The parallel PSO algorithm with heuristic global optimization technique assists the ANN training process to get near optimal solutions precisely. The accuracy and reliability of estimation is audited by actual details of photovoltaic power stations in various regions and scales. The results of estimation model can not only assist the electricity dispatcher to explicitly monitor the trend of solar power generation in different areas, but also coordinate with traditional power plants to meet load demand more accurately. The presented model will bring benefits to power dispatching for larger scales of intermittent and unstable solar power generation.

Stenting is a common method for treating atherosclerosis. A metal or polymer stent is deployed to open the stenosed artery or vein. After the stent is deployed, the blood flow dynamics influence the mechanics by compressing and expanding the structure. If the stent does not respond properly to the resulting stress, vascular wall injury or re-stenosis can occur. In this work, Discrete Multiphysics is used to study the mechanical deformation of the coronary stent and its relationship with the blood flow dynamics. The major parameters responsible for deforming the stent are sort in terms of dimensionless numbers and a relationship between the elastic forces in the stent and pressure forces in the fluid is established. The blood flow and the stiffness of the stent material contribute significantly to the stent deformation and affect the rate of deformation. The stress distribution in the stent is not uniform with the higher stresses occurring at the nodes of the structure.

This study presents a methodology to reveal traces of viral particles, as aerosol with known chemical and molecular structure, in a sample by means of photon and electron interactions. The method is based on Monte Carlo simulations and on the analysis of photon-electron fluxes-spectra through energy channels counts as a function of different aerosol viral concentrations in the air sample and looking at the peculiar photon/electron interactions with the potential abnormal atomic hydrogen (H), oxygen (O), carbon (C), and phosphorus (P) compositions present in the air sample as a function of living and nonliving matter with PO4 group RNA/DNA strands in a cluster configuration.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

The rapid increase in the number of mobile phone base stations (MPBS) has raised global concerns about the potential adverse health effects of exposure to radiofrequency electromagnetic fields (RF-EMF). The application of machine learning techniques can enable healthcare professionals and policymakers to proactively address concerns surrounding RF-EMF exposure near MPBS. In this study, we investigated the potential of machine learning models to predict health symptoms associated with RF-EMF exposure in individuals residing near MPBS.We utilized support vector machine (SVM) and random forest (RF) algorithms, incorporating 11 predictors related to participants' living conditions. A total of 699 adults participated in the study, and model performance was assessed using sensitivity, specificity, accuracy, and the area under the receiver operating characteristic curve (AUC). The SVM-based model demonstrated strong performance, achieving accuracies of 85.3%, 82%, 84%, 82.4%, and 65.1% for headache, sleep disturbance, dizziness, vertigo, and fatigue, respectively. The corresponding AUC values were 0.99, 0.98, 0.920, 0.89, and 0.81. Compared to the RF model and a previously developed model, the SVM-based model exhibited higher sensitivity, particularly for fatigue, with sensitivities of 70.0%, 83.4%, 85.3%, 73.0%, and 69.0% for these five health symptoms. Particularly for predicting fatigue, sensitivity and AUC were significantly improved (70% vs 8% and 11.1% for SVM, MLPNN, and RF, respectively, and 0.81 vs 0.62 and 0.64, for SVM, MLPNN, and RF, respectively). These findings suggest that machine learning methods, specifically SVM, hold promise in effectively managing health symptoms in individuals residing near or planning to settle in the vicinity of MPBS.

Recently, federated learning (FL) has been receiving great attention as an effective machine learning method to avoid the security issue in raw data collection as well as to distribute the computing load to edge devices. However, even though wireless communications is a essential part for implementing FL in edge networks, there have been a few works that analyze the effect of wireless networks on FL. In this paper, we investigate FL in small-cell networks where multiple base stations (BSs) and users are located according to homogeneous Poisson point process (PPP) with different densities. We comprehensively analyze the effects of geographic node deployment on the model aggregation in FL on the basis of stochastic geometry-based analysis. We derive the closed-form expressions of coverage probability with tractable approximations and discuss the minimum required BS density for achieving a target model aggregation rate in small-cell networks. Our analysis and simulation results provide insightful information for understanding the behaviors of FL in small-cell networks, and it can be exploited as a guideline for designing the network facilitating the wireless FL.

Background: The outbreak of the severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2) resulted in the global COVID-19 pandemic. The urgency for an effective SARS-CoV-2 vaccine has led to the development of a first series of vaccines at unprecedented speed. The discovery of SARS-CoV-2 spike-glycoprotein mutants, however, and consequentially the potential to escape vaccine-induced protection and increased infectivity, demonstrates the persisting importance of monitoring SARS-CoV-2 mutations to enable early detection and tracking of genomic variants of concern. Results: We developed the CoVigator tool with three components: 1) a knowledge base that collects new SARS-CoV-2 genomic data, processes it and stores its results; 2) a comprehensive variant calling pipeline; 3) an interactive dashboard highlighting the most relevant findings. The knowledge base routinely downloads and processes virus genome assemblies or raw sequenc-ing data from the COVID-19 Data Portal (C19DP) and the European Nucleotide Archive (ENA), respectively. The results of the variant calling pipeline are visualized through the dashboard in the form of tables and customizable graphs, making it a versatile tool for tracking SARS-CoV-2 variants. We put a special emphasis on the identification of intrahost mutations and make available to the community what is, to the best of our knowledge, the largest dataset on SARS-CoV-2 intrahost mutations. In the spirit of open data, all CoVigator results are available for download. The CoVigator dashboard is accessible via covigator.tron-mainz.de. Conclusion: With increasing demand worldwide in genome surveillance for tracking the spread of SARS-CoV-2, CoVigator will be a valuable resource of up-to-date list of mutations, which can be incorporated into global efforts to sustainably prevent or treat infections.

The functions of annexin A1 (ANXA1) that is expressed on membranes and in cytoplasmic granules have been fully described. Nonetheless, the role of this protein in protecting against DNA damage in the nucleus is still emerging and requires further investigation. Here, we investigated the involvement of ANXA1 in DNA damage response in placental cells. Placenta was collected from ANXA1 knockout mice (AnxA1-/-) and pregnant women with gestational diabetes mellitus (GDM). The placental morphology and ANXA1 expression, which are related to the modulation of cellular response markers in the presence of DNA damage, were analyzed. Total area of AnxA1-/- placenta was smaller because of reduced labyrinth zone, enhanced DNA damage, and impaired base excision repair (BER) enzymes, which resulted in the induction of apoptosis in the labyrinthine and junctional layers. The placentas from pregnant women with GDM showed reduced expression of AnxA1 in the villous compartment, increased DNA damage, apoptosis, and reduction of enzymes involved in the BER pathway. Our translational data provide valuable insights into the possible involvement of ANXA1 in the response of placental cells to oxidative DNA damage and represent advancement in investigations on the mechanisms involved in placental biology.

For the emerging autonomous swarm technology, from the perspective of systems science and systems engineering, there must be some novel elements and methods to aggregate multiple systems into a group, which distinguish with the general components with specific functions, and we expect to provide the presentation of their existence in the swarm development processes. The inspiration of our methodology origins from the integration of swarm ontology, multi-paradigm modeling, multi-agent system, cyber-physical system, etc. Therefore, we choose the model-driven technology as a framework to acquire an approach of model representation across the multiple levels of abstraction and composition. The autonomous strategic mechanism is defined and formed in parallel with ConOps analysis and systems design, so as to effectively solve the cognitive problem of emergence caused by the nonlinear causation among individual and whole behaviors. This approach highlights to use the MBSE processes and their artifacts to embed the meso mechanism to integrate the operational and the functional, and which means to connect the macro and micro aspects in formalism and so to become a whole with its expected goals, and then to verify and validate within a L-V-C simulation environment.

In winter sports, the equipment often comes into contact with snow or ice, and this contact generates a force that resists motion. In some sports, such as cross-country skiing, this resistive force can significantly affect the outcome of a race, as a small reduction in this force can give an athlete an advantage. Researchers have examined the contact between skis and snow in detail, and to fully understand this friction, the entire ski must be studied at various scales. At the macro scale, the entire geometry of the ski is considered and the apparent contact between the ski and the snow is considered and at the micro scale the contact between the snow and the ski base ski-base textures. In the present work, a method for characterising contact between the ski-base texture and virtual snow will be presented. Six different ski-base textures will be considered. Five of them are stone-ground ski bases, and three of them have linear longitudinal textures with a varying number of lines and peak-to-valley height, and the other two are factory-ground “universal” ski bases. The sixth ski base has been fabricated by a steel-scraping procedure. In general, the results show that a ski base texture with a higher Spk-value has less real contact area, and that the mutual differences can be large for surfaces with similar Sa-values. The average interfacial separation is, in general, correlated with the Sa-value, where a “rougher” surface exhibits a larger average interfacial separation. The results for the reciprocal average interfacial separation, which is related to the Couette type of viscous friction, were in line with the general consensus that a “rougher” texture performs better at high speed than a “smoother” one, and it was found that a texture with high Sa and Spk values resulted in a low reciprocal average interfacial separation and consequently low viscous friction. The reciprocal average interfacial separation was found to increase with increasing real contact area, indicating a correlation between the real area of contact and the Couette part of viscous friction.

Abiotic stresses, including drought, salinity, cold, heat, and heavy metals, extensively reduce global agricultural production. Approaches such as conventional breeding and transgenic breeding have been widely used to cope with these environmental stresses. The clustered regularly interspaced short palindromic repeat- Cas (CRISPR/Cas) based gene-editing tool has revolutionized due to its simplicity, accessibility, adaptability, flexibility, and wide applicability. This system has a great potential to build up crop varieties with enhanced tolerance against abiotic stresses. In this review, we summarize the most recent findings on understanding the mechanism of abiotic stress response in plants and the application of CRISPR/Cas mediated gene-editing system towards enhanced tolerance to drought, salinity, cold, heat, and heavy metals stresses. Furthermore, in this review, we highlighted the recent advancements in prime editing and base editing tools for crop improvement.

Using density functional theory (DFT) and the information-theoretic approach (ITA) quantities to appreciate the energetics and properties of biopolymers is still an unaccomplished and ongoing task. To this end, we studied the building blocks of nucleic acid base pairs and small peptides. For base pairs, we have dissected the relative importance of energetic components by using two energy partition schemes in DFT. Our results convincingly show that the exchange-correlation effect predominantly governs the molecular stability of base pairs while the electrostatic potential plays a minor but indispensable role, and the steric effect is trivial. Furthermore, we have revealed that simple density-based ITA functions are in good relationships with molecular polarizabilities for a series of 30 hydrogen-bonded base pairs and all 20 natural α-amino acids, 400 dipeptides, and 8000 tripeptides. Based on these lines, one can easily predict the molecular polarizabilities of larger peptides, even proteins as long as the total molecular wavefunction is available, rather than solving the computationally demanding coupled-perturbed Hartree-Fock (CPHF) equation or its DFT counterpart coupled-perturbed Kohn-Sham (CPKS) equation.

In the diagnosis of olfactory neuroblastoma (ONB), the presence of S-100–positive sustentacular cells surrounding the tumor is important; however, these are also present in normal nasal sinus epithelium. Although ONB often has a different final diagnosis, complete resection of the tumor has a good prognosis and minimally affects the patient's treatment plan. When the tumor extends around the internal carotid artery (ICA), complete resection is difficult due to the high risk of vascular injury; revascularization using a high-flow bypass can avoid this complication. In the present case, the tumor was located in the left sphenoid sinus and extended around the ICA. Preoperative biopsy tissue was positive for neuroendocrine markers and slightly positive for S-100 protein, leading to a diagnosis of ectopic ONB. High-flow bypass revascularization with trapping of the ICA allowed complete tumor resection. The postoperative histopathological diagnosis was neuroendocrine carcinoma, showing no S-100 protein–positive cells. There was no sign of recurrence two and a half years after surgery without additional treatment. This case demonstrates that the presence of S-100 protein–positive cells in ONB may be misleading. Although misdiagnosis of ectopic ONB should be anticipated, a complete resection of the tumor is an effective treatment strategy.

Laser shock peening as an innovative surface treatment technology can effectively improve the fatigue life, sur-face hardness, corrosion resistance, and residual compressive stress. Compared with the laser shock peening, the warm laser shock peening (WLSP) is a new surface treatment technology to improve materials’ surface performances, which takes advantage of thermal mechanical effects on stress strengthening and micro-structure strengthening, results in more stable distribution of the residual compressive stress under heating and cyclic loading process. In this paper, the microstructure of GH4169 nickel super-alloy processed by WLSP technology with differ-ent laser parameters were investigated. The proliferation and tangling of dislocations in GH4169 were observed and the dislocation density increased after WLSP treatment. The influences of different treatment by LSP and WLSP on the microhardness distribution of the surface and along cross-sectional depth were investi-gated. The microstructure evolution of the GH4169 alloy being shocked with WLSP were studied by TEM. The effect of temperature on the stability of high temperature microstructure and properties of GH4169 alloy WLP was investigated.

Through the half-unit circle area computation using the integration of the corresponding curve power series representation, we deduce a slow converging positive infinite series to $\pi$. However, by studying the remainder of that series we establish sufficiently close inequalities with equivalent lower and upper bound terms allowing us to estimate, more precisely, how the series approaches $\pi$. We use the obtained inequalities to compute up to four-digit denominator, what are in this sense, the best rational numbers that can replace $\pi$. It turns out that the well-known convergents of the continued fraction of $\pi$, $22/7$ and $355/113$ called, respectively, Yuel\"{u} and Mil\"{u} in China are the only ones found. Thus we apply a similar process to find rational estimations to $\pi+e$ where $e$ is taken as the power series of the exponential function evaluated at $1$. For rational numbers with denominators less than $2000$, the convergent $920/157$ of the continued fraction of $\pi+e$ turns out to be the only rational number of this type.

Vertical-channel organic dual-gate/base transistors would be highly interesting since vertical organic transistors are the fastest organic transistors demonstrated today. However, incorporating a dual gate/base structure into an ultra-short channel vertical architecture represents a substantial challenge. Here, we successfully realize a new device concept of vertical organic permeable dual-base transistors (OPDBTs), where either of both base electrodes can be used to change the on-currents and tune the threshold voltages. The optimized devices yield a high on-current density of 1.54 A cm^-2 and a large current gain of 9.2×10⁵, corresponding to a high transmission value of 99.998%. The detailed operation mechanisms are investigated by calibrated TCAD simulations with the Poole-Frenkel mobility model, Gaussian density of states and tunneling model. Finally, high-performance logic circuits, e.g. inverter, NAND/AND computation functions are demonstrated with one single OPDBT operating at supply voltages of < 2.0 V. We believe that OPDBTs offer a compact and technologically simple hardware platform with excellent application potential for vertical-channel organic transistors in complex logic circuits.

Background: Iranian traditional medicine is a holistic school of medicine with a long prolific history. It describes numerous concepts and the relationships between them. However, no unified terminology has been proposed for the concepts of this medicine up to the present time. Considering the extensive use of concepts in the numerous textbooks written by the scholars over centuries, comprehending the totality of the terminology is obviously a very challenging task. To resolve this issue and overcome the obstacles, and code the concepts in a reusable manner, constructing an ontology of the concepts of Iranian traditional medicine seems a necessity.Methods: Makhzan al-Advieh, an encyclopedia of materia medica compiled by Mohammad Hossein Aghili Khorasani, was selected as the resource to create an ontology of Mizaj. The steps followed to accomplish this task included (1) compiling the list of classes for Mizaj; (2) arranging the classes in taxonomy; (3) determining object properties and their cardinalities; (4) specifying annotation properties including codes, labels, synonyms, and definitions for each concept; (5) reviewing the fields pertaining to Mizaj of all monographs in Makhzan al-Advieh. The ontology was created using Protégé with adherence to the principles of ontology development provided by the Open Biological and Biomedical Ontology (OBO) foundry. Results: Mizaj ontology was constructed with a final inclusion of 105 classes, three object properties, and 1078 axioms in the Iranian Traditional Medicine General Ontology database, IrGO, freely available at http://jafarilab.com/irgo/. An indented tree view and an interactive graph view using WebVOWL were used to visualize the ontology. All classes were linked to their instances in the UNaProd database to create a knowledge-base of Mizaj. Conclusion: We constructed an ontology-based knowledge base of ITM concepts of Mizaj in the domain of materia medica to help offer a shared and common understanding of this concept, enable reuse of the knowledge, and make the assumptions explicit. Extending IrGO will bridge the gap between traditional and conventional schools of medicine and help guide future research on new treatment options.