A recent study revealed a persistent presence of the PP-Spike recombinant protein in 50% of individuals who received ModRNA injections, contrasting with unvaccinated controls, whether SARSCoV-2 infected or not, up to 187 days post-injection. The implications of these findings are discussed in the context of PP-Spike recombinant protein-induced hyperimmune/inflammatory reactions and thrombotic vasculitis as mechanisms to elucidate the serious side effects, long-term organ complications, and excess deaths observed after administering Covid ModRNA products. These results underscore the urgent need for a comprehensive reassessment of the risk-benefit profile of ModRNA injections, including an immediate halt in their use for any person, and a renewed emphasis on understanding and addressing their long-term effects on human health

In the preparation of polymer-clay nanocomposites the chemical incompatibility between the clay surface and polyolefins can be overcome by using clays organically modified with short chain organic cations. The compatibility can be further enhanced by using functionalized polymer that wets the clay surface while being miscible with the non-polar polymer matrix. In this work we tried to modify the host polymer polypropylene (PP) by irradiating it with gamma-rays in air knowing that it undergoes oxidation and chain scission simultaneously. Thus lower molecular weight PP with highly polar surface due to oxidation can be expected to play double role of clay modifier and functional compatibilizer. This has been observed to be the case. Finely ground PP granules were irradiated in air in a ⁶⁰Co γ-irradiator at the dose rate of 0.08 kGy/h (low dose rate to enhance oxidation) to 5, 10, and 20 kGy total doses. The extent of oxidation and change in molecular weight were determined by ATR-FTIR and Melt Flow Rate measurements respectively. PP/MMT nanocomposites were prepared by using 20% γ-PP, 1-5 % MMT and pristine PP to make up the total 100 in a torque rheometer. Maleated PP was also used in similar quantities to compare the effectiveness of γ-PP as a compatibilizing agent. Nanocomposites prepared with 10 kGy irradiated PP was found to show optimum mechanical properties among all formulations, with 26% increase in E-modulus and 10% increase in tensile strength as compared to pristine PP. Ternary PP nanocomposites were characterized by XRD, SAXS and PALS studies.

Introduction: PP, also called plantar ligament, is a fibrocartilaginous structure found in the metatarsophalangeal (MP) and interphalangeal (IP) joints. The aim of our study is to evaluate the role of MRI, both in standard position and with joint hyperextension, “stress test” (ST), in the study of the plantar plate (PP) disease that involves metatarsophalangeal joints. Material and methods: 25 patients were recruited into our study over a two-year period, 15 positive for metatarsal pain and 10 controls. All symptomatic patients were evaluated before treatment (surgery). Hence, the imaging features were reflective of the natural and true state of the lesions. Results:25 patients were recruited into our study over a two-year period, 15 positive for metatarsal pain and 10 controls. In symptomatic patients: 11/15 demonstrated plantar plate tear/dysfunction on both standard position and stress test, 2/15 had plantar plate tear on stress test (tear not showed on standard position), and 2/12 had no plantar plate tear on both standard position and stress test. The latter two patients showed dorsal subluxation on stress test due to micro-instability for plantar plate failure. In asymptomatic patients, 9/10 were negative for plantar plate dysfunction, and 1/10 was positive for plantar plate dysfunction (dorsal subluxation demonstrated only on stress test), without plantar plate tear. Conclusion:Standard MRI reported, in asymptomatic patients, a specificity of 100% and high NPV (90%), incremented by the ST (NPV and specificity 100%). In symptomatic patients, PP evaluation on standard MRI reported sensitivity of 80%, while stress test increased sensitivity to 100%; in the evaluation of dorsal subluxation of the metatarsophalangeal joint, the sensitivity was 60% (standard MRI) but reached 100% with ST. "Stress test" is an easy task to perform and even affordable in terms of time-consuming (requiring only one additional T2-weighted MRI sequence) for both patients and operators.

Mechanical recycling of solid plastic wastes on a small-scale level can be accomplished with the correct approaches. Thermoplastics are mostly considered for mechanical recycling because of their physical properties and ease of reprocessing. This paper reviews the mechanical reprocessing techniques of selected thermoplastics (polyethylene terephthalate and polyolefins) since they constitute a significant proportion of plastics used commercially. Furthermore, necessary considerations for effective operation of small-scale plants, including energy requirements of machinery and optimisation in order to improve efficiency and product quality, are discussed. A clearer understanding and addressing of the process-related challenges will lead to successful establishment and management of small-scale mechanical recycling facilities to benefit communities. Efficient small-scale mechanical reprocessing establishments have become essential in reducing the environmental impacts of solid plastic wastes and for energy conservation.

In this paper, we introduced many new notions and new contraction named as S-weakly contraction after that we obtained the p-common best proximity point theorems for different types of contractions in the setting of complete metric spaces by using weak P_p-property and proved the uniqueness of these points. Also we presented some examples to prove the validity of our results.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

This paper presents results from numerical and experimental investigation on Charpy tests in order to point out failure mechanisms and to evaluate new polymeric blends PP+PA6+EPDM. Charpy tests were done for initial velocity of the impactor of 0.96 m/s and its mass of 3.219 kg and these data were also introduced in the finite element model. The proposed model take into account the system of four balls, including support and the ring of fixing the three balls and it has a finer discretization of the impact area to highlight the mechanisms of failure and their development in time. The constitutive models for four materials (polypropylene with 1% Kritilen, two blends PP+PA6+EPDM and a blend PA6+EPDM) were derived from tensile tests. Running simulations for each constitutive model of material makes possible to differentiate the destruction mechanisms according to the material introduced in the simulation, including the initiation and the development of the crack(s), based on equivalent plastic strain at break (EPS) for each material. The validation of the model and the simulation results was done qualitatively, analysing the shape of broken surfaces and comparing them to SEM images and quantitatively by comparing the impact duration, energy absorbed by the sample, the value of maximum force during impact. The duration of the destruction of the specimen is longer than the actual one, explainable by the fact that the material model does not take into account the influence of the material deformation speed in Charpy test, the model being designed with the help of tests done at 0.016 m/s (1000 mm/min) (maximum strain rate for the tensile tests). Experimental results are encouraging for recommending the blends 20% PP+42% PA6+28% EPDM and 60% PA6+ 40%EPDM as materials for impact protection at low velocity (1m/s). Simulation results are closer to the experimental ones for the more brittle tested materials (with less content of PA6 and EPDM) and more distanced for the more ductile materials (with higher content of PA6 and EPDM).

Remote sensing technology is crucial for accurate rooftop detection, benefiting urban planning, disaster management, and solar resource estimation. This study employs Efficient Interactive Segmentation (EISEG) to enhance the efficiency of remote sensing image labeling, with a particular focus on rooftop detection. It is necessary to use modern technology because traditional manual labelling methods are labor-intensive and complicated. The study introduces a novel framework on deep learning semantic segmentation models, facilitating an efficient approach to rooftop identification using high-resolution UAV remote sensing datasets. Large dataset of labeled UAV rooftop building images, in which each superpixel region is assigned a binary label indicating rooftop presence. Advanced methods including Asymmetric Neural Network (ANN), Dual At-tention Network (DANet), PP-LiteSeg, and Deeplab3 are implemented for automatic rooftop detection due to their higher performance and advanced architectures. These models are executed on the Baidu deep learning platform PaddlePaddle, generating initial rooftop segmentation maps crucial for estimating photovoltaic resources. The ANN model emerges with the highest accuracy at 96%, followed by DANet at 95.09%, PP-LiteSeg at 94.54%, and Deeplab3 at 81.61%. The outcomes presenting efficient models for automated rooftop identification, and demonstrating the continuous need for improving deep learning techniques in smart and sustainable cities.

The article presents the results of tests of minor head losses through PVC and PP elbows for a flow of water and mixtures of water and sand with grain sizes of up to 0.5 mm and concentrations of 5.6 g∙L-1, 10.84 g∙L-1, and 15.73 g∙L-1. The tests were carried out at variable flow velocities for three elbow diameters of 63, 75, and 90 mm. The flow rate, pressure difference in the tested cross-sections, and temperature of the fluids were measured and automatically recorded. The results of the measurements were used to develop mathematical models for determining the minor head loss coefficient as a function of elbow diameter, sand concentration in the liquid, and Reynolds number. The mathematical model was developed by cross validation. It was shown that when the concentration of sand in the liquid was increased by 1.0 g∙L-1, the coefficient of minor head loss through the elbows increased, in the Reynolds number range of 4.6∙104 − 2.1∙105, by 0.3−0.01% for PP63, 0.6−0.03 % for PP75, 1.1−0.06 % for PP90, 0.8−0.01 % for PVC63, 0.8−0.02 % for PVC75, and 0.9−0.04 % for PVC90. An increase in Re from 5∙104 to 2∙106 for elbows with diameters of 63, 75 and 90 mm caused a 7.3 %, 6.8 %, and 6.0 % decrease in the minor head loss coefficient, respectively.