This work investigates the use of Non-destructive tests as a tool for monitoring the structural performance of concrete structures. The investigation encompassed four phases; the first of which involved the use of destructive and non-destructive mechanisms to assess concrete strength on cube specimens. The second phase research focused on site assessment for a twin engineering theatre located at the Faculty of Engineering, University of Lagos using rebound hammer and ultrasonic pulse velocity tester. The third phase was the use of linear regression analysis model with MATLAB to establish a relationship between calibrated strength as well as ultrasonic pulse velocities with their corresponding compressive strength values on cubes and values obtained from existing structures. Results show that the root-mean squared-R² values for rebound hammer ranged between 0.275 and 0.742 while ultrasonic pulse velocity R² values were in the range of 0.649 and 0.952 for air curing and water curing systems respectively. It initially appeared that the Ultrasonic pulse velocity was more suitable for predicting concrete strength than rebound hammer but further investigations showed that the latter was adequate for early age concrete while the former was more suited for aging concrete. Hence, a combined use is recommended in this work.

Acoustic emission monitoring (AEM) has emerged as an effective technique for detecting wire-breaks resulting from, e.g., stress corrosion cracking, and its application on prestressed concrete bridges is increasing. The success of this monitoring measure depends crucially on a carefully designed sensor layout. For this the attenuation of elastic waves within the structure’s material is determined ideally in-situ through object-related measurements with a reproducible signal source, typically a rebound-hammer. This assumes that the attenuation coefficients derived from rebound-hammer tests are comparable to those from wire-breaks, thus allowing their results to be directly applied to wire-break detection without further adjustments. This study challenges this assumption by analysing attenuation behaviour through an extensive dataset. Employing time-domain and frequency analysis, the research generates attenuation profiles from laboratory experiments and in-situ measurements across various girders and bridge structures, extracting the slope and standard deviation of the residuals. While generally validating this approach, the findings highlight differences in attenuation behaviour from among wire-break signals and rebound-hammer impulses, whereby the latter potentially underestimates the relevant attenuation of wire-breaks by approximately 20 %. Consequently, a transfer factor is proposed to adjust object-related measurement results for wire-break scenarios, including a variance of 1.0 dB/m to cover a 95 % confidence interval for sample scattering. Moreover, the anisotropic attenuation behaviour across different structures was studied, showing that transverse attenuation consistently exceeds the longitudinal, significantly influenced by structural features such as voids. In prefabricated concrete bridges with in-situ-cast concrete slabs, transverse signal transmission remains unhindered across multiple elements. Finally, the results provide a valuable reference for the design of sensor layouts in bridge monitoring, particularly benefiting scenarios where direct in-situ experiences are lacking.

On-stream inspections are the most appropriate method for routine inspections during plant operation without going through production downtime. Ultrasonic inspection, one of the on-stream inspection methods, faces challenges when performed at high temperatures exceeding the recommended 52°C. This study aims to determine the ultrasonic velocity and attenuation with the known material grade, thickness, and temperatures by comparing theory calculation versus experiment with temperatures ranging between 30°C to 250°C on low carbon steel covering most petrochemical equipment material and working conditions. The theoretical analysis was to obtain Young's modulus, Poisson's ratio, and longitudinal velocity at different temperatures. The experiments validated the predicted results of ultrasonic change due to temperature increase and showed a maximum error of 3%. The experimental data of velocity and decibel change from the temperature range provide a reference for the future when dealing with unknown materials information on site that require a quick corrosion status determination.

Sensing Technology (ST) plays a key role in Structural Health Monitoring (SHM) systems. ST focuses on developing sensors, sensory systems or smart materials that monitor a wide variety of materials properties aiming to create smart structures and smart materials, using Embedded Sensors (ESs), and allowing continuous and permanent measurements of the structural integrity. The integration of ESs is limited to the processing technology to embed the sensor due to its high-temperature sensitivity and the possibility of damage during its insertion into the structure. In addition, the technological process selection is dependent on the base material composition, either metallic or composite parts. The selection of smart sensors or the technology underlying them is fundamental to the monitoring mode. This paper presents a critical review of the fundaments and applications of sensing technologies for SHM employing ESs, focusing on the actual developments and innovation of these, as well as analysing the challenges that these technologies present, to build a path that allows a connected world through distributed measurement systems.

Acquisition of real-time hydraulic data is an essential component for flood forecasting. However, we frequently face difficulties in obtaining discharge data using classical contact methods during high magnitude floods and for systems experiencing rapid hydro-geomorphological adjustment. Therefore, we developed low-cost, non-contact sensors and platforms that are designed to overcome these difficulties. These advances enable flood flow properties to be monitored at multiple locations across a river catchment, at low-cost, and communicated in near real-time by using an image velocimetry method. This is an optics-based approach for stream flow measurement using commercially available near-infrared digital cameras to acquire video footage in full HD (30fps). Video footage is then subjected to optical flow tracking techniques based on cross-correlation, and feature-based tracking, enabling the displacement rates of detected features (for example natural foam, seeds, woody debris, and turbulent structures) to be computed. This manual provides step by step guidance to install an image-based gauging station. It contains the list of necessary components, the calibration process of a new camera and the assembly procedure of the system.

The present paper aims to increase knowlodge of the methods of resistance estimating of concrete in situ by means of non-destructive tests used to integrate the quantitative results from cylindrical specimens (core). The results of experimental investigations carried out on concrete conglomerate samples of a school building are shown. The experimental campaign then will be presented like a case study, conducted on a series of concrete beams and pillars of an existing building. The distructive tests on cores were conducted at the Civil Structures Laboratory of the Engineering Department of the University of Campania "Luigi Vanvitelli". The expression obtained through the calibration procedure of the values of non-destructive tests with those provided by the core drills allowed to estimate the average values of the compressive strength of the concrete. It is highlighted how this result was achieved with a very limited core number provided that they are extracted in selected points and that there was a proportionality link with the resistances obtained from non distructive tests.

Kinetic parameters of SO2 adsorption on unburned carbons from lignite fly ash and activated carbons based on hard coal dust were determined. The model studies were performed using the linear and non-linear regression method for the following models: pseudo first and second-order, intraparticle diffusion, and chemisorption on a heterogeneous surface. The quality of the fitting of a given model to empirical data was assessed based on: R2, R, Δq, SSE, ARE, χ2, HYBRID, MPSD, EABS, and SNE. It was clearly shown that it is the linear regression that more accurately reflects the behaviour of the adsorption system, which is consistent with the first-order kinetic reaction – for activated carbons (SO2+Ar) or chemisorption on a heterogeneous surface – for unburned carbons (SO2+Ar and SO2+Ar+H2O(g)+O2) and activated carbons (SO2+Ar+H2O(g)+O2). Importantly, usually, each of the approaches (linear/non-linear) indicated a different mechanism of the studied phenomenon. A certain universality of the χ2 and HYBRID functions has been proved, the minimization of which repeatedly led to the lowest SNE values for the indicated models. Fitting data by any of the non-linear equations based on the R or R2 functions only, cannot be treated as evidence/prerequisite of the existence of a given adsorption mechanism.

Electromagnetic sensors have been used for inspecting small surface defects of metals. Based on the eddy-current thin-skin regime, a revised algorithm is proposed for a triple-coil drive-pickup eddy-current sensor scanning over long surface crack slots (10 mm) with different rotary angles. The method is validated by the voltage measurement of the designed EC sensor scanning over a benchmark (ferromagnetic) steel with surface defects of different depths and rotary angles. With an additional sensing coil for the designed EC sensor, the defect angle (or orientation) can be measured without spatially and coaxially rotating the excitation coil. By referring to the voltage change (due to the defect) diagram (voltage sum versus voltage different) of two sensing pairs, the rotary angle of the surface crack is retrieved with a maximum residual deviation of 3.5 %.

In an industrial environment, the quality assurance of weld seams requires extensive efforts. The most commonly used methods for that are expensive and time-consuming destructive tests, since quality assurance procedures are difficult to integrate into production processes. Beyond that, available test methods allow only the assessment of a very limited set of characteristics. They are either suitable for determining selected geometric features or for locating and evaluating internal seam defects. The presented work describes an evaluation methodology based on microfocus X-ray computed tomography scans (µCT scans) which enable the 3D characterization of weld seams, including internal defects such as cracks and pores. A 3D representation of the weld contour, i.e., the complete geometry of the joint area in the component with all quality-relevant geometric criteria, is an unprecedented novelty. Both the dimensions of the weld seam and internal defects can be revealed, quantified with a resolution down to a few micrometers and precisely assigned to the welded component. On the basis of the methodology developed within the framework of this study, the results of the scans performed on the alloy AA 2219 can be transferred to other aluminum alloys. In this way, the data evaluation framework can be used to obtain extensive reference data for the calibration and validation of inline process monitoring systems employing Deep Learning-based data processing.

The motivation of this work is to investigate experimentally the influence of non-thermal plasma (NTP) application on the reaction kinetics of atmospheric pressure steam gasification of charcoal using a thermostatically controlled drop tube reactor. A gliding-arc generator provides about 1 kW electrical power NTP. For comparison thermal gasification is investigated under comparable flow and specific energy input conditions providing additional heat to the steam. Optical temperature measurement 20 cm flow down of the NTP zone is utilized to characterize the specific enthalpy of the reactive flow. The composition of produced syngas is measured by a gas analyzer and used for the calculation of gas flow rates. The results show a NTP-enhancement on the production of individual syngas components (H2, CO, CH4), especially on hydrogen production by around 39%. The syngas-based carbon conversion and hydrogen release are calculated from the carbon and hydrogen balance between the correspondent content in syngas and in the feedstock. The NTP promoted the carbon conversion and hydrogen release by 25% and 31%, respectively. The first-order reaction kinetics are determined by data-fitting in an Arrhenius diagram. The plasma enhanced the reaction rate coefficients by 27%. Based on experimental results and other literature, possible plasma-induced reactions are proposed.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

This study aimed to explore the feasibility of using airborne acoustic emission in laser beam butt welding for the development of an automated classification system based on neural networks. The focus was on monitoring the formation of joint gaps during the welding process. To simulate various sizes of butt joint gaps, controlled welding experiments were conducted, and the emitted acoustic signals were captured using audible to ultrasonic microphones. To implement an automated monitoring system, a method based on short-time Fourier transformation was developed to extract audio features, and a convolutional neural network architecture with data augmentation was utilized. The results demonstrated that this non-destructive and non-invasive approach was highly effective in detecting joint gap formations, achieving an accuracy of 98%. Furthermore, the system exhibited promising potential for low latency monitoring of the welding process. The classification accuracy for various gap sizes reached up to 90%, providing valuable insights for characterizing and categorizing joint gaps accurately. Additionally, increasing the quantity of training data with quality annotations could potentially improve the classifier model's performance further. This suggests that there is room for future enhancements in the study.

Abstract: Background: Non-invasive acquistion of beat-to-beat pulse transit time (PTT) via piezoelectric/piezocapacitive sensors (PES/PCS) may expand perioperative hemodynamic monitoring. This study evaluated the ability for PTT via PES/PCS to correlate with systolic, diastolic, and mean invasive blood pressure (SBPIBP, DBPIBP, and MAPIBP) and to detect SBPIBP fluctuations. Methods: PES/PCS and IBP measurements were performed in 20 patients undergoing abdominal, urological, and cardiac surgery. A Pearson’s correlation analysis (r) between 1/PTT and IBP was performed. The predictive ability of 1/PTT with changes in SBPIBP was determined by area under the curve (reported as AUC, sensitivity, specificity). Results: Significant correlations between 1/PTT and SBPIBP were found for PES (r=0.64) and PCS (r=0.55) (p<0.01), as well as MAPIBP/DBPIBP for PES (r=0.6/0.55) and PCS (r=0.5/0.45) (p<0.05). A 7% decrease in 1/PTTPES predicted a 30% SBPIBP decrease(0.82, 0.76, 0.76), while a 5.6% increase predicted a 30% SBPIBP increase (0.75, 0.7, 0.68). A 6.6% decrease in 1/PTTPCS detected a 30% SBPIBP decrease (0.81, 0.72, 0.8), while a 4.8% 1/PTTPCS increase detected a 30% SBPIBP increase (0.73, 0.64, 0.68). Conclusions: Non-invasive beat-to-beat PTT via PES/PCS demonstrated significant correlations with IBP and detected significant changes in SBPIBP. Thus PES/PCS as a novel sensor technology may augment intraoperative hemodynamic monitoring during major surgery.

In remote sensing applications, one of the key points is the acquisition, real-time pre-processing and storage of information. Due to the large amount of information present in the form of images or videos, compression of this data is necessary. Compressed sensing (CS) is an efficient technique to meet this challenge. It consists in acquiring a signal, assuming that it can have a sparse representation, using a minimal number of non-adaptive linear measurements. After this CS process, a reconstruction of the original signal must be performed at the receiver. Reconstruction techniques are often unable to preserve the texture of the image and tend to smooth out its details. To overcome this problem, we propose in this work, a CS reconstruction method that combines the total variation regularization and the non-local self-similarity constraint. The optimization of this method is performed by the augmented Lagrangian which avoids the difficult problem of non-linearity and non-differentiability of the regularization terms. The proposed algorithm, called denoising compressed sensing by regularizations terms (DCSR), will not only perform image reconstruction but also denoising. To evaluate the performance of the proposed algorithm, we compare its performance with state-of-the-art methods, such as Nesterov's algorithm, group-based sparse representation and wavelet-based methods, in terms of denoising, and preservation of edges, texture and image details, as well as from the point of view of computational complexity. Our approach allows to gain up to 25% in terms of denoising efficiency, and visual quality using two metrics: PSNR and SSIM.

The moisture content of maize seed is an important indicator for evaluating seed quality and a fundamental item in grain testing. The experiment used direct drying method to measure the moisture content of 80 different varieties of maize samples, and captured their images using a hyperspectral imaging (HSI) system in the spectral range of 1100~2498nm. By comparing seven spectral preprocessing methods, the PLSR model established after Normalize pretreatment had the best effect. The characteristic wavelengths were selected by Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS) and Uninformative Variable Elimination (UVE). Twelve prediction models were established for full band spectra and characteristic wavelengths based on PLSR, PCR and SVM. By comparing the performance of the prediction models, it was found the Normalize-SPA-PLSR algorithm was optimized. The values of RC2 and RP2 in the model were higher, which were 0.9936 and 0.9933, respectively, while the values of RMSEP and RMSECV were lower, which were 0.0357 and 0.0380, respectively. The Normalize-SPA-PLSR model was used as a visual prediction model for moisture content of maize seed, the 20 maize varieties in the prediction set were visualized to obtain visualized color images of moisture content. The color differences between different moisture content images were significant. The result indicated that hyperspectral imaging could accurately, rapidly, and non-destructive predict moisture content of maize seed, which provided technical support for moisture content detection in the process of maize harvest, storage and processing.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

Flare stacks are a key element in the safety of petrochemical and refinery industries; the correct operating conditions thereof must be ensured through a schedule for the periodic reviewing of all parts thereof. Advances in Non-Destructive Testing (NDT) in recent years and the application thereof to this field allow reliable, objective information to be obtained. This article describes and groups together the main applicable NDT techniques, analysing their advantages and disadvantages, updated with the new possibilities offered by unmanned aircraft or drones.

Regression models form the core of the discipline of econometrics. One of the basic assumptions of classical linear regression model is that the values of the explanatory variables are fixed in repeated sampling. However, in most of the real life cases, particularly in economics the assumption of fixed regressors is not always tenable. Under a non-experimental or uncontrolled environment, the dependent variable is often under the influence of explanatory variables that are stochastic in nature. There is a huge literature related to stochastic regressors in various aspects. In this paper, a historical perspective on some of the works related to stochastic regressor is being tried to pen down based on literature search.

To assess the community health workers’ (CHWs) knowledge, attitude, and practices (KAP) in type-2 diabetes (T2D) and hypertension (HTN) management. We thus also sought to assess the potential health system barriers for incorporating CHWs in T2D and HTN management. Mixed-method study comprised (1) a survey among 153 active CHWs to assess their KAP of T2D and HTN, and (2) semi-structured interviews with key informants to understand challenges of the health system and proposed solutions in incorporating CHWs in T2D and HTN management. The majority of CHWs correctly answered general knowledge questions on NCDs, risk factors, and prevention; however, only one-quarter correctly answered questions on smoking, family history, or tobacco use as risk factors. Most respondents appeared to have positive attitudes and have been practicing some activities related to T2D and HTN. Both financial and non-financial resource constraints were cited as challenges of the health system; therefore, re-structuring the role definition of CHWs and task of responsibilities, and assessment the need and workload have been proposed as ways forwards to effectively incorporate CHWs in T2D and HTN care. CHWs in Cambodia have shown their potential in T2D and HTN management; however, a well-designed strategy including technical training, clearly defined roles and responsibilities, and strong supporting structure are important to maximize their potential in the health system.

Cavitation bubbles are commonly existing in shipbuilding engineering, ocean engineering, mechanical engineering, chemical industry, and aerospace. Asymmetric deformation of bubble occurs near the boundary, and the non-spherical cavitation bubbles have strong destructive effects, inducing high amplitude loading at the nearby boundary. The purpose of this paper is to investigate the laser-induced of cavitation bubble, non-spherical collapse behavior near the boundary. In this study, experimental data such as bubble pulsation process and bubble surface velocity distribution were obtained by high-speed camera technique and full-field velocity calculation. The results show that the bubble appeared non-spherical collapse shapes, near different boundaries, with near-hemispherical, near-ellipsoidal, near-cone and near-pea shapes, and the bubble surface velocity distribution is not uniform. When bubble near the free surface or rigid boundary, the smaller the stand-off r is, the more obvious the repulsive effect of the free surface and the attractive effect of the rigid boundary are. As the stand-off r decreases, the larger the Bjerknes force and the bubble surface velocity difference, the more pronounced the non-spherical shape.

The authors of the paper have made an attempt to detect the fibre content and fibre spacing in a steel fibre reinforced concrete (SFRC) industrial floor. Two non-destructive testing (NDT) methods: an electromagnetic induction technique and a radar-based technique were applied. The first method allowed to detect the spacing in subsequent layers located in the thickness of the slab. The result of the second method was a 3D visualization of the detected fibre in the volume of concrete slab. The conducted tests showed aptitude and limitations of the applied methods in estimating fibre volume and spacing. The two techniques also allowed to locate the areas with relatively low fibre concentration which are very likely to be characterized by low mechanical properties.

Prompt removal of misfolded membrane proteins and misassembled membrane protein complexes is essential for membrane homeostasis. However, the elimination of these toxic proteins from the hydrophobic membrane environment has high energetic barriers. Transmembrane FtsH is the only known ATP-dependent protease responsible for this task, unlike other well-studied soluble ATP-dependent proteases. The mechanisms by which FtsH recognizes, unfolds, translocates, and proteolyzes its substrates remain unclear. Here, we report the crystal structures of the Thermotoga maritima FtsH periplasmic domain (PD) in an associative trimeric state at a 1.5-1.95 Å resolution. We also describe the pH-dependent oligomerization states of the isolated PD using dynamic light scattering. These observations help us understand how FtsH recognizes membrane-anchored misfolded proteins.

Electromagnetic sensing has been used for diverse applications of non-destructive testing, including the surface inspection, measurement of properties, object characterization. However, the measurement accuracy could be significantly influenced by the lift-off between sensors and samples. To address the issue caused by lift-offs, various strategies have been proposed for the permeability measurement of ferromagnetic steels, which mainly involves different sensor designs and signal features (e.g., the zero-crossing feature). In this paper, a single high-frequency scenario for the permeability retrieval is introduced. By combining the signal of two sensing pairs, the retrieval of magnetic permeability is less affected by the lift-off of sensors. Unlike the previous strategy on reducing the lift-off effect (directly taking the phase term out of the integration) using the Dodd-Deeds analytical method, the proposed method is based on a high-frequency linear feature of the phase term. Therefore, this method has the merit of high accuracy and fast processing for the permeability retrieval (a simplified version of Dodd-Deeds analytical formulas after the integration). Experimental measurement has been carried out on the impedance measurement of designed sensors interrogating ferromagnetic dual-phase steels. For sensor lift-offs of up to 10 mm, the error of the permeability retrieval is controlled within 4 % under the optimal frequency.

Diagnosis and prognosis of failures for aircrafts’ integrity are some of the most important regular functionalities in complex and safety-critical aircraft structures. Further, development of failure diagnostic tools such as Non-Destructive Testing (NDT) techniques, in particular, for aircraft composite materials, has been seen as a subject of intensive research over the last decades. The need for diagnostic and prognostic tools for composite materials in aircraft applications rises and draws increasing attention. Yet, there is still an ongoing need for developing new failure diagnostic tools to respond to the rapid industrial development and complex machine design. Such tools will ease the early detection and isolation of developing defects and the prediction of damages propagation; thus allowing for early implementation of preventive maintenance and serve as a countermeasure to the potential of catastrophic failure. In this paper, following a short introductory summary and definitions, this paper provides a brief literature review of recent research on failure diagnosis of composite materials with an emphasis on the use of NDT techniques in aerospace industry. In addition to this, within a some of significant NDT application extents, prognosis of composites is also briefly discussed.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

We present a new penalized method for estimation in sparse logistic regression models with group structure. Group sparsity suggests us to consider the Group Lasso penalty. Being different from penalized log-likelihood estimation, our method can be viewed as a penalized weighted score function method. Under some mild conditions, we provide non-asymptotic oracle inequalities promoting group sparsity of predictors. A modified block coordinate descent algorithm based on a weighted score function is also employed. The net advantage of our algorithm over the existing Group Lasso-type procedures is that the tuning parameter can be pre-specified. The simulations show that this algorithm is considerably faster and more stable than competing methods. Finally, we illustrate our methodology with two real data sets.

For the soil in different regions, the nutrient fertility contained in it is different, and the detection and zoning management of soil nutrients before tillage every year can improve grain yield. In this paper, an integrated learning strategy model based on black soil hyperspectral data is designed for rapid classification of organic matter content classification of black soil. Soil hyperspectral image dataset of Xiangyang Experimental Base was collected; by changing the internal structure of the stacking model, an LSVM-stacking model with (MLP, SVC, DTree, XGBl, kNN) five classifiers as the L1 layer was built, and the simulated annealing algorithm was used for hyperparameter optimization. Compared to other stacking models, the LSVM-stacking metrics are significantly improved. The accuracy rate of hyperparameter optimization is improved by 38.6515%, the accuracy rate of the independent test data set is 0.9488, and the comparison of individual learners can improve the recognition classification accuracy of label"1" to 1.0.

Developing efficient Artificial Intelligence (AI)-enabled system to substitute human role in non-destructive testing is an emerging topic of considerable interest. In this study, we propose a novel impact-echo analysis system using online machine learning, which aims at achieving near-human performance for assessment of concrete structures. Current computerized impact-echo systems commonly employ lab-scale data to validate the models. In practice, however, the echo patterns can be far more complicated due to varying geometric shapes and materials of structures. To deal with a large variety of unseen data, we propose a sequential treatment for echo characterization. More specifically, the proposed system can adaptively update itself to approaching human performance in impact-echo data interpretation. To this end, a two-stage framework has been introduced, including echo feature extraction and the model updating scheme. Various state-of-the-art online learning algorithms have been reviewed and evaluated for the task. To conduct experimental validation, we collected 10,940 echo instances from multiple inspection sites with each sample had been annotated by human experts with healthy/defective condition labels. The results demonstrated that the proposed scheme achieved favorable echo pattern classification accuracy with high efficiency and low computation load.

The presented study is focused on the impact of binding zones locations at immunochromatographic test strips into analytical parameters of multiplex lateral flow assay. Due to non-equilibrium conditions for such assays the duration of immune reactions influences significantly on analytical parameters, and the integration of several analytes into one multiplex strip may cause essential decrease of sensitivity. To choose the best location of binding zones, we have tested reactants for immunochromatographic assays of lincomycin, chloramphenicol, and tetracycline. The influence of the distance to the binding zones on the intensity of coloration and limit of detection (LOD) was rather different. Basing on the obtained data, the best order of binding zones was chosen. In comparison with non-optimal location the LODs were 5-10 fold improved. The final assay provides LODs 0.4, 0.4 and 1.0 ng/mL for lincomycin, chloramphenicol, and tetracycline, respectively. The proposed approach can be applied for multiassays of other analytes.

The identification of fetal cells in the blood and tissues of healthy mothers raised questions about the potential alloreactive origins of various diseases, such as autoimmunity, diabetes, arteriosclerosis, and cancer. However, the extent to which alloreactivity contributes to these diseases remains unverified. This study presents a basic mathematical disease model based on the genes’ origin and immunological interactions. This model, grounded in set theory, classifies these immunological interactions based on their intrinsic, extrinsic, and allogeneic nature. Therefore, this model offers an unexpected common theoretical foundation for understanding alloreactivity, genetic diseases, and infections. Furthermore, this model provides a valuable framework for scrutinizing the role of alloreactivity in health and disease.

In ancient buildings, timber members could need specific on-site interventions, including reinforcement or repair, sometimes inserting of reinforcing material into grooves routed in the original sound wood. Grooves number, positions and dimensions, and strengthening materials may differ, according to the desired increase of bending stiffness and strength. The Modulus-of-Elasticity (MOE) of each beam is of key importance, but the incisions can affect it, net of the reduction of the removed wood. In this study 12 old beams were accurately measured and their static and dynamic MOEs calculated before and after the grooves processing, to simulate the operations of typical reinforcing interventions. One groove was routed along the length of each beam and deepened progressively by three steps. Tests have showed how the MOE is affected by the groove depth, decreasing up to one third. The paper proves how the weakening effect of grooves on-site can be assessed with dynamic MOE and roughly predicted by means of visual survey. Grooves need for strengthening beams, must be carefully evaluated because of the variation of the actual mechanical properties, net to lost wood.

This paper presents the development of an underwater crack detection system for structural integrity assessment of submerged structures, like offshore oil and gas installations, underwater pipelines, underwater foundations for bridges, dams etc. Focus is on use of machine learning based approaches. First a detailed literature review of state of the current methods for underwater surface crack detection is presented highlighting challenges and opportunities. An overview of image augmentation approach for creation of underwater optical effects is also presented. Experimental results using standard network based machine learning approach, used for surface crack detection in onshore environment, is presented. Series of Test cases are presented where existing networks performance are improved using augmented images for underwater conditions. The experimental results demonstrate the effectiveness and accuracy of the proposed system in detecting cracks in underwater structures. The system has the potential to improve the safety and reliability of underwater structures and prevent catastrophic failures.

Alternating current field measurement (ACFM) testing is one of promising techniques in the field of non-destructive testing with advantages of the non-contact capability and the reduction of lift-off effects. In this paper, a novel crack detection approach is proposed to reduce the effect of the angled crack (cack orientation) by using rotated ACFM techniques. The sensor probe is composed of an excitation coil and two receiving coils. Two receiving coils are orthogonally placed in the centre of the excitation coil where the magnetic field is measured. It is found that the change of the x component and the peak value of the z component of the magnetic field when the sensor probe rotates around a crack follows a sine wave shape. A customised accelerated finite element method solver programmed in MATLAB is adopted to simulate the performance of the designed sensor probe which can significantly improve the computation efficiency due to the small crack perturbation. The experiments have also been carried out to validate the simulations. It is found that the ratio between the z and x components of the magnetic field remains stable under various rotation angles. It shows the potential to estimate the depth of the crack from the ratio detected by combining the magnetic fields from both receiving coils (i.e., the x and z components of the magnetic field) using the rotated ACFM technique.

Eddy current testing can be used to interrogate steels but it is hampered by the lift-off distance of the sensor. Previously, the lift-off point of intersection (LOI) feature has been found for the pulsed eddy current (PEC) testing. In this paper, a lift-off invariant inductance (LII) feature is proposed for the multi-frequency eddy current (MEC) testing, which merely targets the ferromagnetic steels. That is, at a certain working frequency, the measured inductance signal is found nearly immune to the lift-off distance of the sensor. Such working frequency and inductance are termed as the lift-off invariant frequency (LIF) and LII. Through simulations and experimental measurements of different steels under the multi-frequency manner, the LII has been verified to be merely related to the sensor parameters and independent of different steels. By referring to the LIF of the test piece and using an iterative inverse solver, one of the steel properties (either the electrical conductivity or magnetic permeability) can be reconstructed with a high accuracy.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

Regression models are mostly used in all fields of sciences for modelling the relationship between a dependent variable and independent variable(s). The least square method is often used to estimate the parameters in a linear model because it is the best linear unbiased estimator. These estimates can only be reliable if the assumption of normality is satisfied. In some cases the dependent variable might be bimodal and shows a non-linear relationship with the independent variable(s). In this case, a non-linear model should be used. In non-linear model, the standard errors are often obtained by linearizing the nonlinear function around the parameter, assuming central limit theorem. After the linearization, the least square parameter estimates are obtained. It should be noted that the error of the non-linear model is different from that of the transformed linear model. Thus, there is a need to transform back to the original non-linear model. In this note, a novel non-linear function was developed into a non-linear regression model, called Normal-Power model. The least square method was used to estimate the parameter of the transformed model. Its usefulness in regression model was demonstrated using real data of Nigeria Economy-Tourism model.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

COVID-19 vaccine hesitancy and its enablers would shape community uptake of non-covid vaccines such as oral cholera vaccine (OCV) in the post-COVID-19 era. This study assessed the impact of COVID-19 vaccine hesitancy and its drivers on OCV hesitancy in a cholera endemic region of the Democratic Republic of Congo. We conducted a community-based survey in Bukavu. The survey included characteristics, intention to take OCV and COVID-19, reasons for COVID-19 hesitancy, and thinking and feeling about COVID-19 vaccines. Poisson regression analyses were performed. Of the 1708 respondents, 84.66% and 77.57% were hesitant to OCV alone and to both OCV and COVID-19, respectively. Hesitancy to COVID-19 vaccines rose OCV hesitancy by 12% (crude Prevalence Ratio, [cPR]=1.12, 95%CI[1.03-1.21]). Independent predictors of OCV hesitancy were living in semi-urban area (adjusted Prevalence Ratio [aPR]=1.10, 95%CI[1.03-1.12]), religious refusal of vaccines (aPR=1.06, 95%CI[1.02-1.12]), concerns about vaccine safety (aPR=1.05, 95%CI[1.01-1.11]) and adverse effects (aPR=1.06, 95%CI[1.01-1.12]), as well as poor knowledge (aPR=1.07, 95%CI[1.01-1.14]). Conversely, the belief about COVID-19 vaccine effectiveness reduced OCV hesitancy (aPR=0.76, 95%CI[0.62-0.93]). COVID-19 vaccine hesitancy and its drivers exhibiting a significant domino effect on OCV uptake. Addressing vaccine hesitancy through community-based health literacy interventions would likely improve the introduction of novel non-COVID-19 vaccines in post-COVID-19 era.

The classical approach to non-linear regression in physics, is to take a mathematical model describing the functional dependence of the dependent variable from a set of independent variables, and then, using non-linear fitting algorithms, extract the parameters used in the modeling. Particularly challenging are real systems, characterised by several additional influencing factors related to specific components, like electronics or optical parts. In such cases, to make the model reproduce the data, empirically determined terms are built-in the models to compensate for the impossibility of modeling things that are, by construction, impossible to model. A new approach to solve this issue is to use neural networks, particularly feed-forward architectures with a sufficient number of hidden layers and an appropriate number of output neurons, each responsible for predicting the desired variables. Unfortunately, feed-forward neural networks (FFNNs) usually perform less efficiently when applied to multi-dimensional regression problems, that is when they are required to predict simultaneously multiple variables that depend from the input dataset in fundamentally different ways. To address this problem, we propose multi-task learning (MTL) architectures. These are characterized by multiple branches of task-specific layers, which have as input the output of a common set of layers. To demonstrate the power of this approach for multi-dimensional regression, the method is applied to luminescence sensing. Here the MTL architecture allows predicting multiple parameters, the oxygen concentration and the temperature, from a single set of measurements.

Non-intrusive load monitoring (NILM) is a core technology for demand response (DR) and energy conservation services. Traditional NILM methods are rarely combined with practical applications, and most studies aim to decompose the whole loads in a household, which leads to low identification accuracy. In this paper, an NILM approach based on multi-feature integrated classification (MFIC) is explored, which combines some non-electrical features such as ON/OFF duration, usage frequency of appliances, and usage period to improve load differentiability. The implementation of MFIC algorithm is consistent with traditional event-based method. The uniqueness of our algorithm is that it designs an event detector based on steady-state segmentation and a linear discriminant classifier group based on multi-feature global similarity. Simulation results using an open-access dataset demonstrate the effectiveness and high accuracy of MFIC algorithm, with the state-of-the-art NILM methods as benchmarks.

We explores the hydrodynamical limit of a homogeneous electron gas, considering the interplay between the infrared limit and phenomenological hydrodynamics. Our study involves interactions generated by non-linear coordinate transformations. The focus begins with an analysis of non-linear coordinate transformations and their impact on normal modes in a harmonic system. The Lagrangian for a harmonic oscillator is used as an illustrative example, highlighting the role of position-dependent effective mass in preventing certain coordinate values. Moving beyond single degrees of freedom, we extend the discussion to a system with several harmonic degrees of freedom, introducing a collective variable. The effective dynamics of this collective variable are defined through a Lagrange multiplier term, emphasizing linearity in the description. Our study extends to the Current Two-Point function (CTP) formalism, introducing matrices and their inverses, such as $\hD$ and $\hD^{-1}$. Further, we delve into the dynamics of current in a homogeneous electron gas at finite density and zero temperature. Green's functions are generated using a functional integral approach, and the effective action is constructed via functional Legendre transformation. The quadratic part of the generator functional is expanded to derive the effective action, leading to the Maxwell equation and the subsequent elimination of the photon field. The resulting effective action for current dynamics is expressed in terms of the Current Two-Point function, paving the way for further exploration of the hydrodynamical aspects of the electron gas. Our study combines theoretical developments and mathematical formalism to provide insights into the hydrodynamical behavior of homogeneous electron gases.

Gradual disability worsening in Multiple Sclerosis (MS) is indicative of confirmed progression that mostly involves progression independent of relapse activity (PIRA) and is associated with neurodegeneration. Insights from pathology reveal grey matter involvement (neocortex, hippocampus, spinal cord, and deep grey matter structures) and microglia activation in early stages of MS. Cortical lesions result in thinning and atrophy and are considered accurate predictors of disability progression and cognitive decline.Neuroimaging biomarkers, such as high-resolution 7T MR images and TSPO-PET, have been examined for the detection of cortical pathology linked to cognitive deficits and thus progression, but are limited in clinical practice due to availability, time constraints, and cost.Electroencephalography (EEG) emerges as a non-invasive, cost-effective tool that reflects cortical activity in MS. Its potential in monitoring cognitive impairment is explored by focusing on nonlinear EEG analysis. The MuST PREDICT^TM project aims to extract linear and nonlinear EEG features, investigating their role in predicting disease progression and optimizing treatment. The study employs retrospective, cross-sectional, and prospective designs, utilizing EEGs from various MS forms, cognitive assessments, serum/cerebrospinal fluid biomarkers and neuroimaging. The methodology involves time-based and spectral feature extraction, employing artificial intelligence classifiers and brain criticality-based approaches.The conceptual framework of an innovative modality is herein presented, that would EEG for early MS progression detection. Standardization of the methodology could lead to the creation of a digital tool for better prognostication and treatment strategy optimization.

Peanuts, owing to their composition of complex carbohydrates, plant protein, unsaturated fatty acids, and essential minerals (magnesium, iron, zinc, and potassium), hold significant potential as a vital component of the human diet. Additionally, their low water requirements and nitrogen fixation capacity make them an appropriate choice for cultivation in adverse environmental conditions. The germination ability of seeds profoundly impacts the final yield of the crop, assessing seed viability of extreme importance. Conventional methods for assessing seed viability and germination are both time-consuming and costly. To address these challenges, this study investigated Visible-Near Infrared Spectroscopy (Vis/NIR) in the wavelength range of 500-1030 nm as a non-destructive and rapid method to determine the viability of two varieties of peanut seeds: North Carolina-2 (NC-2) and Spanish flower (Florispan). The study subjected the seeds to three levels of artificial aging through heat treatment, involving incubation in a controlled environment at a relative humidity of 85% and a temperature of 50°C over 24-hour intervals. The absorbance spectra noise was significantly mitigated and corrected to a large extent by combining the Savitzky-Golay (SG) and Multiplicative Scatter Correction (MSC) methods. To identify the optimal wavelengths for seed viability assessment, a range of meta-heuristic algorithms were employed, including world competitive contest (WCC), league championship algorithm (LCA), Genetics (GA), Particle Swarm Optimization (PSO), Ant Colony Optimization (ACO), imperialist competitive algorithm (ICA), learning automata (LA), heat transfer optimization (HTS), forest optimization (FOA), discrete symbiotic organisms search (DSOS), and cuckoo optimization (CUK). These algorithms offer powerful optimization capabilities for effectively extracting relevant wavelength information from spectral data. Results revealed that all the algorithms demonstrated remarkable accuracy in predicting the allometric coefficient of seeds, achieving correlation coefficients exceeding 0.985 and errors below 0.0036, respectively. In terms of execution time, the ICA (2.3635 seconds) and LCA (44.9389 seconds) algorithms exhibited the most and least efficient performance, respectively. Conversely, the FOA and the LCA algorithms excelled in identifying the least number of optimal wavelengths (10 wavelengths). Subsequently, the seeds were classified based on the wavelengths selected by the FOA (10 wavelengths) and (DSOS (16 wavelengths) methods, in conjunction with logistic regression (LR), decision tree (DT), Multilayer Perceptron (MP), support vector machine (SVM), k-nearest neighbor (K-NN), and NaiveBayes (NB) classifiers. The DSOS-DT and FOA-MP methods demonstrated the highest accuracy, yielding values of 0.993 and 0.983, respectively. Conversely, the DSOS-LR and DSOS-KNN methods obtained the lowest accuracy, with values of 0.958 and 0.961, respectively. Overall, our findings demonstrated that Vis/NIR spectroscopy, coupled with variable selection algorithms and learning methods, presents a suitable and non-destructive approach for detecting seed viability.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

The purpose of this work was to achieve non-destructive detection of the internal defects of in-shell walnuts using X-ray radiography technology based on improved Faster R-CNN network model. First, the FPN structure was added to the feature extraction layer to extract richer image information. Then ROI Align was used to instead of ROI Pooling for eliminating the localization bias problem caused by quantization operation. Finally, the Softer-NMS module was introduced to the final regression layer with the predicted bounding box for improving the localization accuracy of the candidate boxes. The results indicated that the internal defects in intact walnuts with shells could be identified effectively using the proposed improved network model in this study. Specifically, the discrimination accuracy of the in-shell sound, shriveled and empty-shell walnuts were 96.14%, 91.72% and 94.80% respectively, and the highest overall accuracy can reach 94.22 %. Contrasted with original Faster R-CNN network model, the mAP and F1-value of the improved Faster R-CNN model increased by 5.86% and 5.65%, respectively. Consequently, the proposed method can be applied for the in-shell walnuts with shriveled and empty-shell defects.

This paper presents the latest developments in microCT, both globally and locally, for supporting the additive manufacturing industry. There are a number of recently developed capabilities which are especially relevant to the non-destructive quality inspection of additive manufactured parts; and also for advanced process optimization. These new capabilities are all locally available but not yet utilized to their full potential, most likely due to a lack of knowledge of these capabilities. The aim of this paper is therefore to fill this gap and provide an overview of these latest capabilities, showcasing numerous local examples.

Recent research has implicated the gut microbiota in the development of lymphoma. Dysbiosis of the gut microbial community can disrupt the production of gut microbial metabolites, thereby impacting host physiology and potentially contributing to lymphoma. Dysbiosis-driven release of gut microbial metabolites such as lipopolysaccharides can promote chronic inflammation, potentially elevating the risk of lymphoma. In contrast, gut microbial metabolites, such as short-chain fatty acids, have shown promise in preclinical studies by promoting regulatory T-cell function, suppressing inflammation, and preventing lymphoma. Another metabolite, urolithin A, exhibited immunomodulatory and antiproliferative properties against lymphoma cell lines in vitro. While research on the role of gut microbial metabolites in lymphoma is limited, this article emphasizes the need to comprehend their significance, including therapeutic applications, molecular mechanisms of action, and interactions with standard chemotherapies. The article also suggests promising directions for future research in this emerging lymphoma and gut microbiome investigation field.

Observed sea surface Ka-band normalized radar backscatter cross section (NRCS) and Doppler velocity (DV) exhibit energy at low frequencies (LF) below the surface wave range. It is shown that non-linearity in NRCS-wave slope Modulation Transfer Function (MTF) and inherent NRCS averaging within the footprint account for the NRCS and DV LF variance with the exception of VV NRCS for which almost half of the LF variance is attributable to wind fluctuations. Although the distribution of radar DV is quasi-Gaussian suggesting virtually little impact of non-linearity, the LF DV variations arise due to footprint averaging of correlated local DV and non-linear NRCS. Numerical simulations demonstrate that MTF non-linearity weakly affects traditional linear MTF estimate (less than 10% for |MTF|< 20). Thus the linear MTF is a good approximation to evaluate the DV averaged over large footprints typical of satellite observations.

There is increasing evidence that the non-cooperative models describe household structures in developing countries more succinctly compared with the unitary model. Domestic violence against women, which is pervasive in Nigeria even though likely to be under-reported, will need to be understood within the framework of non-cooperative relationship between couples. In this study, we identify factors of domestic violence against women within couples who were currently in marital or cohabiting partnerships. Also, we investigate whether domestic violence influences the decision of women to terminate pregnancies. We use data from the 2018 Nigeria Demographic and Health Survey (NDHS). Multivariate logistic regressions were used to model the predictors of domestic violence, and its influence on the decision to terminate pregnancies among married women. Of the 8,910 married women interviewed for domestic violence, 35.33% had ever experienced a form of domestic violence. We discover that women: with higher education, that is not poor, and resides in urban areas have 44%, 18% and 15% reductions in the odds of experience domestic violence respectively. On the other hand, women who are employed, own land, having husbands/partners that are employed in the agricultural sector, and drink alcohol have 1.16, 1.2, 2.07, and 2.8 times increased odds of experiencing domestic violence accordingly. Also, we uncover that currently married women experiencing domestic violence have 1.25 times increased odds of terminating pregnancies compared with their counterparts that are not experiencing domestic violence. Effectively, poverty, low levels of education, residing in rural areas, drinking habit of husbands/partners, employment, marital capital, and land ownership status of women are risk factors of domestic violence against married women in Nigeria but can be affected by policies and programmes. Importantly, public actions to contain domestic violence in order to improve maternal health should be implemented in the context of the dynamics of a non-cooperative relationship existing between married couples.

Industrial radiography is a pivotal non-destructive testing (NDT) method that ensures quality and safety in a wide range of industrial sectors. Conventional human-based approaches, however, are prone to challenges in defect detection accuracy and efficiency, primarily due to the high inspection demand from manufacturing industries with high production throughput. To solve this challenge, numerous computer-based alternatives have been developed, including Auto-mated Defect Recognition (ADR) using deep learning algorithms. At the core of training, these algorithms demand large volumes of data that should be representative of real-world cases. However, the availability of digital X-ray radiography data for open research is limited by non-disclosure contractual terms in the industry. This study presents a pipeline that is capable of modeling synthetic images based on statistical information acquired from X-ray intensity distribution from real digital X-ray radiography images. Through meticulous analysis of the intensity distribution in digital X-ray images, the unique statistical patterns associated with the exposure conditions used during image acquisition, type of component, thickness variations, beam divergence, anode heel effect, etc., are extracted. The realized synthetic images were utilized to train deep learning models, yielding an impressive model performance with mean intersection over union (IoU) of 0.93, and mean dice coefficient of 0.96, on real unseen digital X-ray radiography images. This methodology is scalable and adaptable, making it suitable for diverse industrial applications.

This research is aimed to develop the method for damage degree evaluation in metals and alloys during their deformation and destruction based on acoustic emission (AE) technique. Experimental studies were carried out on tensile specimens of high-strength steel with simultaneous registration of AE signals in tested material. It was shown that the time-dependent AE primary parameters, such as the AE signal maximum amplitudes and AE activity, do not have a clear relationship with the material damage degree. This fact makes it difficult to use standard methods for assessing the damage degree of acoustic signal sources, including defects. It was proposed to use the Kolmogorov-Smirnov criterion to differ the processes of metal plastic deformation and crack propagation during the rupture. The possibility of estimating the material damage degree by high-energy AE hits share was shown. Besides, a particular expression was obtained for evaluating the damage degree for the material under study.

In response to the growing inspection demand exerted by process automation in component manufacturing, Non-destructive testing (NDT) continues to explore automated approaches that utilize deep learning algorithms for defect identification, including within digital X-ray radiography images. This necessitates a thorough understanding of the implication of image quality parameters on the performance of these deep learning models. This study investigates the influence of two image quality parameters, namely Signal-to-Noise Ratio (SNR) and Contrast-to-Noise Ratio (CNR), on the performance of U-net deep learning segmentation model. Input images were acquired with varying combinations of exposure factors such as kilovoltage, milli-ampere, and exposure time, which altered the resultant quality. The data was sorted into 5 different datasets according to their measured SNR and CNR values. The deep learning model was trained 5 distinct times, utilizing a unique dataset for each training session. Training the model with high CNR values yielded an intersection over Union (IoU) metric of 0.9594 on test data of the same category but drops to 0.5875 when tested on lower CNR test data. The result in this study emphasizes the importance of achieving a balance in training dataset according to the investigated quality parameters, to enhance the performance of deep learning segmentation models in NDT radiography applications.

Early diagnosis and treatment have always been highly desired in the fight against cancer, and detection of circulating tumor DNA (ctDNA) has recently been touted as highly promising for early cancer screening. Consequently, the detection of ctDNA in liquid biopsy gains much attention in the field of tumor diagnosis and treatment, which has also attracted research interest from the industry. However, traditional gene detection technology is difficult to achieve low cost, real-time and portable measurement of ctDNA. Electroanalytical biosensors have many unique advantages such as high sensitivity, high specificity, low cost and good portability. Therefore, this review aims to discuss the latest development of biosensors for minimal-invasive, rapid, and real-time ctDNA detection. Various ctDNA sensors are reviewed with respect to their choices of receptor probes, detection strategies and figures of merit. Aiming at the portable, real-time and non-destructive characteristics of biosensors, we analyze their development in the Internet of Things, point-of-care testing, big data and big health.

Electromagnetic eddy current sensors are commonly used to identify and quantify the surface notches of metals. However, the unintentional tilt of eddy current sensors affects results of size profiling, particularly for the depth profiling. In this paper, based on the eddy current thin-skin regime, a revised algorithm has been proposed for the analytical voltage or impedance of a tilted driver–pickup eddy current sensor scanning across a long ideal notch. Considering the resolution of the measurement, the bespoke driver–pickup, also termed as transmitter-receiver (T-R) sensor is designed with a small mean radius of 1 mm. Besides, the T-R sensor is connected to the electromagnetic instrument and controlled by a scanning stage with high spatial travel resolution , with a limit of 0.2 μm and selected as 0.25 mm. Experiments have been out on the voltage imaging of an aluminium sheet with 7 machined long notches of different depths using T-R sensor under different tilt angles. By fitting the measured voltage (both real and imaginary part) with proposed analytical algorithms, the depth profiling of notches is less affected by the tilt angle of sensors. From the results, the depth of notches can be retrieved within a deviation of 10 % for tilt angles up to 60 degrees.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Eddy current based approaches have been investigated for a wide range of inspection applications. Dodd-Deeds model and the truncated region eigenfunction expansion (TREE) method are widely applied in various occasions, mostly for the cases that the sample is relatively larger than the radius of the sensor coil. The TREE method converts the integral expressions to the summation of many terms in the truncated region. In a recent work, the impedance of the co-axial air-cored sensor due to a plate of finite radius was calculated by the modified Dodd-Deeds analytical approach proposed by authors. In this paper, combining the modified analytical solution and the TREE method, a new finite region eigenfunction expansion (FREE) method is proposed. This method involves modifying its initial summation point from the first zero of the Bessel function to a value related to the radius of the plate, therefore makes it suitable for plate with finite dimensions. Experiments and simulations have been carried out and compared for the verification of the proposed method. Further, the planar size measurements of the metallic circular plate can be achieved by utilising the measured peak frequency feature.

Hyper spectral imaging (HSI) is a technique that is used to obtain the spectrum for each pixel in the image. It helps in finding objects and identifying materials etc. Such an identification is very difficult using other imaging techniques. It allows the researchers to investigate the documents without any physical contact. Nowadays detection of unequal Ink mismatch based on HSI has shown vast improvement in distinguishing the inks. Detection of unequal Ink mismatch is an unbalanced clustering problem. This paper used K-means Clustering for ink mismatch detection. K-means Clustering find same subgroups in the data based on Euclidean distance. This paper demonstrates performance in unequal Ink mismatch based on HSI.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

In this article, we analyze the weak gravitational lensing in the context of Einstein-non-linear Maxwell-Yukawa black hole. To this desire, we derive the deflection angle of light by Einstein-non-linear Maxwell-Yukawa black hole using the Gibbons and Werner method. For this purpose, we obtain the Gaussian optical curvature and implement the Gauss-Bonnet theorem to investigate the deflection angle of Einstein-non-linear Maxwell-Yukawa black hole. Moreover, we derive the deflection angle of light in the presence of plasma medium. We also analyze the graphical behavior of deflection angle by Einstein-non-linear Maxwell-Yukawa black hole in the presence of plasma as well as non-plasma medium.

Laser energy per unit surface, necessary to trigger the material removal, decreases with the pulse shortening becoming the pulse-time independent in the sub-picosecond range. These pulses are shorter the electron-to-ion energy transfer time and electronic heat conduction time minimizing the energy losses. The electrons receiving the energy larger than the threshold, drag the ions off the surface in the mode of electrostatic ablation. We show that the pulse shorter than the ion period (Shorter-the-Limit (StL)) ejects conduction electrons with the energy larger than the work function (from a metal) leaving the bare ions immobile in a few atomic layers. The electrons emission is followed by the bare ion’s explosion, ablation, and THz radiation from expanding plasma. We compare this phenomenon to the classic photo effect, nanocluster Coulomb explosions, show differences and consider possibilities for detecting the new mode of ablation experimentally by emitted THz radiation and consider applications of high-precision nano-machining with this low intensity irradiation.

When 2−1/Q<p≤2, we establish the C^{0,1} and C^{1,α}-regularities of weak solutions to quasi-linear p-Laplacian type non-homogeneous equations in the Heisenberg group.

The present article addresses the long-standing problem of the polymer brush bilayers under stationary shear flow at non-linear response regime where the system gets a non-Newtonian fluid. The main idea behind this research would be the fact that the immense lubricity of the polymer brush bilayers originates from a global restructuring that takes place at large shear rates. It is shown here that physical quantities like, stress tensor, viscosity tensor, the friction coefficient and the chain extensions could become dependent on the shear rate at non-Newtonian regime. Apparently, the sub-linear scaling of the physical quantities at large shear rates is solely due to the fact that the chains stretch in the shear direction.

Quantifying an imaging modality’s ability to reproduce results is important for establishing its utility. In Magnetic Resonance Spectroscopic Imaging (MRSI), new acquisition protocols are regularly introduced, which improve upon their precursors with respect to signal-to-noise ratio (SNR), total acquisition duration, and nominal voxel resolution. This study has quantified the within-subject and between-subject reproducibility of one such new protocol (reduced-Field-of-View-Density-Weighted-Concentric-Ring-Trajectory (rFOV-DW-CRT) MRSI) by calculating the Coefficient of Variance of data acquired from a test-retest experiment. The Posterior Cingulate Cortex (PCC) and the Right Superior Corona Radiata (SCR) were selected as the Regions of Interest (ROIs) for Grey Matter (GM) and White Matter (WM), respectively. CVs for between-subject and within-subject are consistently around or below 15% for Glx, tCho, and Myo-Ins and below 5% for tNAA and tCr.

Subsurface drainage systems remove excess water from the soil profile thereby improving crop yields in poorly drained farmland. Knowledge of the position of the buried drain lines is important: 1) to improve understanding of leaching and offsite release of nutrients and pesticides, and 2) for the installation of a new set of drain lines between the old ones for enhanced soil water removal efficiency. Traditional methods of drainage mapping involve the use of tile probes and trenching equipment. While these can be effective, they are also time-consuming, labor-intensive, and invasive, thereby entailing an inherent risk of damaging the drainpipes. Non-invasive geophysical soil sensors provide a potential alternative solution. Previous research has focused on the use of time-domain ground penetrating radar (GPR), with variable success depending on local soil and hydrological conditions and the central frequency of the specific equipment employed. The objectives of this study were 1) to test the use of a stepped-frequency continuous wave (SFCW) 3D-GPR (GeoScope Mk IV 3D-Radar with DXG1820 antenna array) for subsurface drainage mapping, and 2) to evaluate the performance of a 3D-GPR with the use of a single-frequency multi-receiver electromagnetic induction (EMI) sensor (DUALEM) in-combination. The 3D-GPR system offers more flexibility for application to different (sub)surface conditions due to the coverage of wide frequency bandwidth. The EMI sensor simultaneously provides information about the apparent electrical conductivity (EC_a) for different soil volumes, corresponding to different depths. This sensor combination was evaluated on twelve different study sites with various soil types with textures ranging from sand to clay till. While the 3-D GPR showed a high success rate in finding the drainpipes at five sites (sandy, sandy loam, loamy sand, and organic topsoils), the results at the other seven sites were less successful due to limited penetration depth (PD) of the 3D-GPR signal. The results suggest that the electrical conductivity estimates produced by the inversion of EC_a data measured by the DUALEM sensor could be a useful proxy to explain the success achieved by the 3D-GPR in finding the drain lines. The high attenuation of electromagnetic waves in highly conductive media limiting the PD of the 3D-GPR can explain the findings obtained in this research.

The Zika virus (ZIKV) is a mosquito-borne Flavivirus and can be transmitted through an infected mosquito bite or through human-to-human interaction by sexual activity, blood transfusion, breastfeeding or perinatal exposure. After the 2015-2016 outbreak in Brazil, a strong link between ZIKV infection and microcephaly emerged. ZIKV specifically targets human neural progenitor cells, suggesting that proteins encoded by ZIKV bind and inactivate host cell proteins leading to microcephaly. Here, we present a systematic annotation of interactions between human proteins and the seven non-structural ZIKV proteins corresponding to a Brazilian isolate. The interaction network was generated by combining tandem-affinity purification followed by mass spectrometry with yeast two-hybrid screens. We identified 150 human proteins, involved in distinct biological processes, as interactors to ZIKV non-structural proteins. Our interacting network is composed of proteins that have been previously associated with microcephaly in human genetic disorders and/or animal models. This study builds on previously published interacting networks of ZIKV and genes related to autosomal recessive primary microcephaly to generate a catalog of human cellular targets of ZIKV proteins implicated in processes related to microcephaly in humans. Collectively, this data can be used as a resource for future characterization of ZIKV infection biology and help create a basis for the discovery of drugs which may disrupt the interaction and reduce the health damage to the fetus.

Infection with Zika virus (ZIKV), a member of the Flavivirus genus of the Flaviviridae family, typically results in mild self-limited illness, but severe neurological disease occurs in a limited subset of patients. In contrast, serious outcomes commonly occur in pregnancy that affect the developing fetus, including microcephaly and other major birth defects. The genetic similarity of ZIKV to other widespread flaviviruses, such as dengue virus (DENV), presents a challenge to the development of specific ZIKV diagnostic assays. Nonstructural protein 1 (NS1) is established for use in immunodiagnostic assays for flaviviruses. To address the cross-reactivity of ZIKV NS1 with proteins from other flaviviruses we used site-directed mutagenesis to modified putative epitopes. Goat polyclonal antibodies to variant ZIKV NS1 were affinity-purified to remove antibodies binding to the closely related NS1 protein of DENV. An antigen-capture ELISA configured with the affinity-purified polyclonal antibody showed a linear dynamic range between approximately 500 to 30 ng/mL, with a limit of detection of between 1.95 and 7.8 ng/mL. NS1 proteins from DENV, yellow fever virus, St. Louis encephalitis virus and West Nile virus showed significantly reduced reactivity in the ZIKV antigen-capture ELISA. Refinement of approaches similar to those employed here could lead to development of ZIKV-specific immunoassays suitable for use in areas where infections with related flaviviruses are common.

A large number of bridges are designed and built without considering seismic actions and, differently from buildings, there are currently no comprehensive guidelines to evaluate existing bridges without performing, as in the well known incremental dynamic analysis (IDA), complex non linear dynamic analyses (RHA). Bridges are structurally very different from building but, at the same time, are sensitive to higher modes as well as many multi-storey buildings that inspired innovative pushover procedures such as the well known modal pushover analysis (MPA). In the present study the incremental modal pushover analysis (IMPA), a pushover based approach already proposed and applied on buildings by the same authors, is revised and proposed for bridges (IMPAβ). IMPAβ accounts for the effects of higher modes in order to accurately estimate the seismic response of bridges; the effect of higher modes is considered by introducing a suitable number of modes to ensure the participation of a predefined total effective modal mass. The efficiency of the proposed method is demonstrated by conducting a study on two bridges, one regular and one irregular, and the IDA analysis is employed as reference solution. Numerical results indicate good accuracy of the proposed method in assessing the seismic response and a very good accuracy if compared to other available pushover procedures available in the literature.

Today, the style of light construction materials used in building is one of the most important factors in reducing building's dead load and better performance of the structures in the earthquake. One of the ways to reduce the structure weight is to use lightweight blocks instead of using traditional materials. The main purpose of this research is to compare density, compressive strength and water absorption volume of non-load-bearing lightweight blocks made of natural and artificial lightweight aggregates. Scoria lightweight aggregates of Sanandaj, Ghorveh mine, pumice in Tabriz, Bostanabad mine, and Leca in Leca enterprise have been used to make the samples. Given the importance of the materials used, grading of coarse-grained materials has been conducted based on the standard of 7657 and grading of fine materials have been conducted based on the standard of 302.The experiments' results show that Scoria blocks due to hard texture, and high mechanical resistance of their lightweight aggregates, have had higher compressive strength, and density and lower water absorption volume compared to pumice and Lika lightweight aggregate blocks. Pumice blocks despite having desirable compressive strength and lower density compared to the two other blocks have higher water absorption volume, and do not meet the standard conditions. This same factor causes it faces with less interest. Among these Lika blocks with density of 1151.94 (kg per cubic meter) below 2000 kilograms per cubic meter of Iran density standard of 7782 (28-day compressive strength of 2.57 MPa), higher than 2.5 MPa of Iran compressive strength standard of 7782 (and water absorption volume of 282.92 kg per cubic meter) below 288 kilograms per cubic meter of Iran water absorption volume standard of 7782 (as a non-load-bearing lightweight block) have been diagnosed desirable.

In this work, we investigate the weak deflection angle of light from exact black hole within the non-linear electrodynamics. First we calculate the Gaussian optical curvature using the optical spacetime geometry. With the help of modern geometrical way popularized by Gibbons and Werner, we examine the deflection angle of light from exact black hole. For this desire, we determine the optical Gaussian curvature and execute the Gauss-Bonnet theorem on optical metric and calculate the leading terms of deflection angle in the weak limit approximation. Furthermore, we likewise study the plasma medium's effect on weak gravitational lensing by exact black hole. Hence we expose the effect of the non-linear electrodynamics on the deflection angle in the weak gravitational field.

This paper is intended at highlighting the main mechanical parameters controlling the behavior of the so-called "acceleration-sensitive" Non-Structural Components (NSCs). In the first part a short review of the current state of knowledge and the critical issues related to the prediction of the seismic response of NSCs is reported. Then, the paper presents the results of a numerical parametric analysis intended to capture the key features of the dynamic response of a two-degree-of-freedom (2DOF) system which is supposed to be representative of both the main structure and the "non-structural" component (NSC). Particularly, it allows to simulate the coupled behaviour of both main structure and NSC and evaluating their response. The main parameters controlling the dynamic response of NSCs emerge from this study, which could pave the way towards formulating more mechanically consistent relationships for evaluating the maximum accelerations induced by seismic shakings on NSCs.

The Langmuir isotherm is a widely used model for analyzing adsorption equilibrium data. This study evaluated the efficiency and accuracy of all four linear forms of the Langmuir isotherm and its non-linear form using 67 experimental data sets selected from the literature. The results showed that only if all four linear forms simultaneously show high accuracy, then the non-linear form also shows high accuracy, and therefore it can be said that the process probably follows the Langmuir isotherm. On the contrary, when at least one of the four linear forms of the Langmuir isotherm has low accuracy, it means that the non-linear form also has low accuracy, and it can be concluded that this process does not follow the Langmuir isotherm. This research suggests that all four linear forms of the Langmuir isotherm should be evaluated simultaneously to conclude whether the studied system follows the Langmuir isotherm or not. In other words, relying on only one of the four linear forms of the Langmuir isotherm to model adsorption and calculate the Langmuir constant and maximum adsorption capacity is an incomplete approach, contrary to the conventional approach.

Natural Fibre Composites (NFC) are eco-friendly, sustainable alternatives to synthetic polymers. However, some intrinsic natural fillers´ properties hinder their widespread implementation as re-inforcement in polymeric matrices and require further investigation. In the scope of this study, the thermal, rheologic, mechanical (tension and flexural modes), morphological properties, water ab-sorption and dimensional stability of the NF polypropylene (PP) based injection moulded compo-sites with the rice husk (rh) and olive pits (op) of 20 wt% and 30% wt%, were investigated. The results suggest that the higher content of the rice husk and olive pits led to a similar reduction of the Melt Flow Index (MFI), independent of the additive type compared to virgin polypropylene (PPv). The melting and crystallization temperatures of the PPrh and PPop composites did not change with statistical significance. The composites are stiffer than the PP matrix by up to 49% and possess higher mechanical strength in what concerns the tension mode at the expense of de-creased ductility. PPrh and PPop have superior flexural modulus in the bending mode, while the flexural strength improvement was accomplished for the PP30%rh. The dimensional stability of the composites was improved as the linear shrinkage in the flow direction was decreased by 49% for PPrh and 30% for PPop, positively correlating with an increase in the filler content and stiff-ness. PPop was less susceptible to water sorption than PPrh due to fibres' composition and larger surface-to-area volume ratios.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

Previously, a conductivity invariance phenomena (CIP) has been discovered – at a certain lift-off, the inductance change of the sensor due to a test sample is immune to conductivity variations, i.e. the inductance – lift-off curve passes through a common point at a certain lift-off, termed as conductivity invariance lift-off. However, this conductivity invariance lift-off is fixed for a particular sensor setup, which is not convenient for various sample conditions. In this paper, we propose using two parameters in the coil design – the horizontal and vertical distances between the transmitter and the receiver to control the conductivity invariance lift-off. The relationship between these two parameters and the conductivity invariance lift-off is investigated by simulation and experiments and it has been found that there is an approximate linear relationship between these two parameters and the conductivity invariance lift-off. This is useful for applications where the measurements have restrictions on lift-off, e.g. uneven coating thickness which limits the range of the lift-off of probe during the measurements. Therefore, based on this relationship, it can be easier to adjust the configuration of the probe for a better inspection of the test samples.

The heat release response of the flame to acoustic excitation is a critical factor for understanding combustion instability. In the present work, the nonlinear heat release response of a methane-air non-premixed flame to the low frequency acoustic excitations is experimentally investigated. The flame describing function (FDF) was measured based on the overall CH* chemiluminescence intensity and the velocity fluctuations obtained by two-microphone method. The CH* chemiluminescence images and the schlieren images were analyzed to reveal the mechanism of nonlinear response. The excitation frequency ranges from 10Hz to 120Hz. The forced relative velocity fluctuation amplitude ranges from 0.10 to 0.50. The corresponding flame Strouhal number (Stf) ranges from 0.43 to 4.67. The study has shown that the flame length responds more sensitively to changes in excitation amplitude when subjected to relatively high frequency excitations. The normalized flame length (Lf/D) decreases from 3.79 to 2.37 with the increase of excitation amplitude at excitation frequency of 100Hz. The number of oscillation zones along the flame increases with increasing excitation frequency, which is consistent with the increase of the Stf. The low-pass filtering characteristic of FDF is caused by the dispersion of multiple oscillation zones, as well as the cancellation effect of the adjacent oscillation zones under relatively high frequency excitation. The cancellation effect of the positive and negative oscillation zones with various Stf is main mechanism for the local gain peak and valley. When two adjacent oscillation regions have approximate amplitudes, the overall phase-lag becomes more sensitive to changes in excitation frequency and amplitude. This sensitivity leads to nonlinear anomalous changes in the phase-lag near the frequency corresponding to the gain valley. The calculated disturbance convection time is consistent with the measured time delay in the short flame scenario. Future research is necessary to establish whether the observed agreement occurs due to the oscillation zone consistently occurring proximate to the flame's center of mass, coupled with a precise determination of the average convective velocity.

This paper introduces a novel respiratory detection system based on diaphragm wall motion tracking using an embedded ultrasound sensory system. We assess the utility and accuracy of this method in evaluating diaphragmatic function and its contribution to respiratory workload. The developed system is able to monitor the diaphragm wall activities when the sensor is placed in the zone of apposition (ZOA). This system allows the direct measurements with only one ultrasound PZT5 piezo transducer. The system both generates pulsed ultrasound waves at 2.2 MHz and amplifies reflected echoes. According to the diaphragmatic motions, the respiratory signals of the proposed system is insensitive to human motion artifacts. Promising results were obtained from six subjects on six different tests with an average sensitivity and specificity of 84% and 93% of respiration detection, respectively. Measurements are referenced to a SPR-BTA commercial spirometer. In this study, we also evaluated inertial and photoplethysmography (PPG) sensors as other conventional methods in this area.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

Many papers in recent years have been devoted to estimating the per pixel proportions of three broad classes of materials (e.g. photosynthetic vegetation, non-photosynthetic vegetation and bare soil) using data from multispectral sensors. Many of these papers use estimation methods based on the linear mixture model. Very few of these papers assess the accuracy of their estimators. I show how to produce confidence intervals (CIs) and joint confidence regions (JCRs) for the proportions associated with various linear mixture models. There are two main models, both of which assume that the coefficients in the model are non-negative. The first model assumes that the coefficients sum to 1. The second does not, but uses rescaling of the estimated coefficients to produce estimated proportions. Three variants of these two models are also analysed. JCRs are shown to be particularly informative, because they are typically better at localising the information than CIs are. The methodology is illustrated using examples from Landsat Thematic Mapper data at 1169 locations across Australia, each of which has associated field observations. There is also discussion about the extent to which the methodology can be extended to hyperspectral data.

This article describes the history of research and development of surface-penetrating radar, starting from the 60s in the USSR, and ending today in Russia and neighboring states formed after the collapse of the USSR. The outstanding role played in the initial period of this technology development by Prof. M.I. Finkelstein and his colleagues is highlighted. Their research had a significant impact on subsequent developments in modern Russia and the neighboring countries.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

Soybean with insignificant differences in appearance have large differences in their internal physical and chemical components, therefore follow-up storage, transportation and processing require targeted differential treatment. A fast and effective machine learning method based on hyperspectral data of soybean for pattern recognition of categories is designed as a non-destructive testing method in this paper. A hyperspectral-image dataset with 2299 soybean seeds in 4 categories is collected; Ten features is selected by extreme gradient boosting algorithm from 203 hyperspectral bands in range 400 to 1000 nm; A Gaussian radial basis kernel function support vector machine with optimization by the Tree-structured Parzen Estimator algorithm is built as TPE-RBF-SVM model for pattern recognition of soybean categories. The metrics of TPE-RBF-SVM are significantly improved compared with other machine learning algorithms. The accuracy is 0.9165 in the independent test dataset which is 9.786% higher for vanilla RBF-SVM model and 10.02% higher than the extreme gradient boosting model.

The standard of care measures for kidney function, proteinuria, and serum creatinine (SCr) are poor predictors of early stage kidney disease. Measures that can detect chronic kidney disease in its earlier stages are needed to enable therapeutic intervention and reduce adverse outcomes of chronic kidney disease. We have developed the Kidney Injury Test (KIT) and a novel KIT Score based on the composite measurement and validation of multiple biomarkers across a unique set of 397 urine samples. The test is performed on urine samples that require no processing at the site of collection and without target sequencing or amplification. We sought to verify that the pre-defined KIT test, KIT Score, and clinical thresholds correlate with established chronic kidney disease (CKD) and may provide predictive information of early kidney injury status above and beyond proteinuria and renal function measurements alone. Statistical analyses across six DNA, protein, and metabolite markers were performed on a subset of residual spot urine samples with CKD that met assay performance quality controls from patients attending the clinical labs at the University of California, San Francisco (UCSF) as part of an ongoing IRB approved prospective study. Inclusion criteria included selection of patients with confirmed CKD and normal healthy controls; exclusion criteria included incomplete or missing information for sample classification, logistical delays in transport/processing of urine samples or low sample volume, and acute kidney injury. Multivariate logistic regression of kidney injury status and likelihood ratio statistics were used to assess the contribution of the KIT Score for prediction of kidney injury status and stage of CKD as well as assess the potential contribution of the KIT Score for detection of early stage CKD above and beyond traditional measures of renal function. Urine samples were processed by a proprietary immunoprobe for measuring cfDNA, methylated cfDNA, clusterin, CXCL10, total protein, and creatinine. The KIT Score and stratified KIT Score Risk Group (High versus Low) had a sensitivity and specificity for detection of kidney injury status (healthy or CKD) of 97.3% (95% CI: 94.6%–99.3%) and 94.1% (95% CI: 82.3%–100%). In addition, in patients with normal renal function [eGFR ≥ 90], the KIT Score clearly identifies those with predisposing risk factors for CKD, which could not be picked up by eGFR or proteinuria (p < 0.001). The KIT Score uncovers a burden of kidney injury that may yet be incompletely recognized, opening the door for earlier detection, intervention and preservation of renal function.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Non-alcoholic fatty liver disease (NAFLD) is a liver disorder that has become a global health concern due to its increasing prevalence. Currently, there is a need for reliable biomarkers to aid in the diagnosis and prognosis of NAFLD. Extracellular vesicles (EVs) are promising candidates in biomarker discovery, as they carry proteins that reflect the pathophysiological state of the liver. In this review, we developed a list of EV proteins that could be used as diagnostic biomarkers for NAFLD. We employed a multi-step strategy that involved reviewing and comparing various sources of information. Firstly, we reviewed papers that have studied EVs proteins as biomarkers in NAFLD, as well as papers that have studied circulating proteins as biomarkers in NAFLD. To further identify potential candidates, we utilized the EV database Vesiclepedia.org to qualify each protein. Finally, we consulted the Human Protein Atlas to search for candidates' localization, focusing on membrane proteins. By integrating these sources of information, we developed a comprehensive list of potential EVs membrane protein biomarkers that could aid in the diagnosis and monitoring of NAFLD. In conclusion, our multi-step strategy for identifying EV-based protein biomarkers for NAFLD provides a comprehensive approach that can also be applied for other diseases. The protein candidates identified through this approach could have significant implications for the development of non-invasive diagnostic tests for NAFLD and improve the management and treatment of this prevalent liver disorder.

The present work is a numerical simulation of velocity and mixture fraction fields in a turbulent non-reaction Propane jet flow issuing into parallel co-flowing air, in isothermal condition which has been experimentally described here: http://www.sandia.gov/TNF/DataArch/ProJet.html. The objective is a better understanding of the flow structure and mixing process, a situation in which there is no chemical interaction and heat-transfer. The two-equation Realizable k-ε eddy viscosity turbulence model has been used to simulate the turbulent flow field on a 2D plane (i.e., on a 5-degree sector of the experimental domain), because Realizable k-ε more accurately predicts the spreading rate of both planar and round jets and presents the best proficiency in comparison with all versions of the k-ε models. Afterward, axial and radial profiles of mean velocities, turbulence energy, mean mixture fraction, the mixture fraction half radius (Lf), and the mass flux diagram have been numerically elicited for grid independent mesh (mesh B) and compared with corresponding experimental data to assess the numerical model. To obtain turbulence kinetic energy, k, due to lack of w' in the experimental data, the assumption of w'=v' seems to be valid. Simulations have demonstrated that mean mixture fraction (at radial profiles at locations x/D=0, 4, 15, 30 and 50) and its half radius, Lf, which characterizes jet width expanse, are prominently well-captured; Moreover, mean vertical velocity fields (in X-direction: Umean) have revealed less accuracy but still conspicuously well-captured. However, mean vertical velocity fields (in Y-direction: Vmean) have disclosed less resolution; Likewise, turbulence kinetic energy, k, have manifested moderate accuracy (between Umean and Vmean). It should be noticed that although numerical results for absolute pressure, p, have been obtained on aforementioned sections, there were no experimental data to compare with them. Thus, the corresponding numerical data has not been demonstrated in this study.

For many years, energy monitoring at the most disaggregate level has been mainly sought through the idea of Non-Intrusive Load Monitoring (NILM). Nevertheless, a practical application of this concept in the residential sector should address the underlying concerns raised by the technical specifications of case studies. From one side, such an operation must handle common matters related to the essence of any NILM system. Although this aspect has been thoroughly investigated by basic research, it is limited to the properties of public datasets. On the other side, it must deal with specific concerns corresponding to uncommon situations. These circumstances impose further restrictions on existent NILM schemes, however, they have been overlooked due to the lack of pertinent databases to scrutinize. Accordingly, this paper presents applied research on a potential solution to NILM for Quebec residences. It carries out a relevant investigation into the multi-faceted nature of this problem in order to reveal barriers to feasible implementations in the context of Quebec. This work commences with a concise discussion about the NILM idea to highlight its essential requirements for a fruitful practice. Afterward, it provides a comparative statistical analysis to represent the specificity and potential challenges of the case study in accordance with NILM necessities. For this purpose, the examination exploits data from real-world measurement systems in the same and European regions. Subsequently, this study focuses on a load identification exercise by proposing a combinatory approach that utilizes the promise of sub-meter smart technologies to integrate the intrusive aspect of load monitoring with the non-intrusive one. The former is aimed at extracting overall heating demand from the aggregate one by a supervised procedure based on Deep Learning (DL) models while the latter is designed for disaggregating the residual load through an unsupervised process on the basis of clustering techniques. The results demonstrate that geographically-dependent cases create electricity consumption scenarios under which existing NILM methods can be questioned. From a realistic standpoint, this research elaborates on critical remarks to realize viable NILM systems, particularly, in Quebec houses.

The preservation of the authenticity of a building artefact is a responsible practice. On the other side, the need to save the building artefact from the natural and anthropic degradation, to ensure the structural reliability to the different actions, to define an efficient maintenance program are big challenges, that involves the cooperation of several professionals, responsible use of innovative techniques and materials that are nowadays available. This paper focuses on a specific design approach for the rehabilitation works of ancient constructions in archaeological sites. The proposed conceptual design approach implies different steps that allow the optimization of the design at an increasing level of knowledge on the existing structures and their materials. The design procedure on historical constructions generally includes the following steps: the collection of data, the structural identification, hazard, and vulnerability analysis, damage and risk analysis, a cost-benefit analysis, so only at the end of the process, the final design is achieved. In the archaeological area, some important design aspects cannot be defined before the execution work phase, since some elements could be revealed and identified during work execution, as a consequence, the final design has been often optimized after all this information has been acquired. A studied case in the archaeological site of Pompeii is herein presented to prove the efficiency of the proposed approach.

A cuprous oxide (Cu₂O) thin layer served as the base for a non-enzymatic glucose sensor in an alkaline medium, 0.1 NaOH solution, with a linear range of 50-200 mg/dL using differential pulse voltammetry (DPV) measurement. An X-ray photoelectron spectroscopy (XPS) study confirmed the formation of the cuprous oxide layer on the thin gold film sensor prototype. Quantitative detection of glucose in both phosphate-buffered saline (PBS) and undiluted human serum were carried out. Neither ascorbic acid nor uric acid even at a relatively high concentration level of 100mg/dL in serum interfered with the glucose detection, demonstrating the excellent selectivity of this non-enzymatic cuprous oxide thin layer based glucose sensor. Chronoamperometry (CA) and single potential amperometric voltammetry were used to verify the measurements obtained by differential pulse voltammetry (DPV), and the positive results validated that the detection of glucose in a 0.1 M NaOH alkaline medium by DPV measurement was effective. Nickel, platinum and copper are commonly used metals for non-enzymatic glucose detection. The performance of these metal-based sensors for glucose detection using DPV were also evaluated. Cuprous oxide (Cu₂O) thin layer based sensor showed the best sensitivity for glucose detection among the sensors evaluated.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) responsible for the disease COVID-19 has wreaked havoc on the health and economy of humanity. In addition, the disease is observed in domestic and wild animals. The disease has impacted directly and indirectly every corner of the planet. Currently, there are no vaccines and effective therapies for COVID-19. SARS-CoV-2 is an enveloped virus with a single-stranded RNA genome of 29.8 kb. More than two-thirds of the genome comprises Orf1ab encoding 16 non-structural proteins (nsps) followed by mRNAs encoding structural proteins, spike (S), envelop (E), membrane (M), and nucleocapsid (N). These genes are interspaced with several accessory genes (open reading frames [Orf] 3a, 3b, 6, 7a, 7b, 8, 9b, 9c and 10). The functions of these proteins are of particular interest for understanding the pathogenesis of SARS-CoV-2. Several of the nsps (nsp3, nsp4, nsp6) and Orf3a are transmembrane proteins involved in regulating the host immunity, modifying host cell organelles for viral replication and escape and hence considered drug targets. In this paper we report mapping the transmembrane structure of the non-structural proteins of SARS-CoV-2.

In this work, quantum dynamics of a spin-0 particle under the effects of Lorentz symmetry violation in the presence of Coulombtype non-electromagnetic potential $(S(r) ∝ \frac{1}{r})$ is investigated. The non-electromagnetic (or scalar) potential is introduced by modifying the mass term via transformation $M → M + \frac{η_c}{r}$ in the relativistic wave equation. The linear central potential induced by the Lorentz symmetry violation is a linear radial electric and constant magnetic field and, analyze the effects on the spectrum of energy and the wave function

We construct a family of two-step optimal fourth order iterative methods for finding single root of non-linear equations. We generalize these methods to simultaneous iterative methods for determining all the distinct as well as multiple roots of single variable non-linear equations. Convergence analysis is present for both cases to show that the order of convergence is four in case of single root finding method and is twelve for simultaneous determination of all roots of non-linear equation. The computational cost, Basin of attraction, efficiency, log of residual and numerical test examples shows, the newly constructed methods are more efficient as compared to the existing methods in literature.

In this paper, we introduce a non-invasive approach for monitoring bridge infrastructure with ground-based interferometric radar. This approach is called the mirror mode, since it utilises the flat surface of the bridge underside as a mirror to reflect the signal to a corner reflector on the ground placed opposite of the radar sensor. For proving the feasibility of this approach, a measurement campaign has been carried out at an exemplary bridge in Karlsruhe (Germany) including a radar sensor in mirror mode, a second radar sensor in the default mode and a laser profile scanner. We investigate the potential of this approach to monitor the bridge displacement in vertical direction and compare the results with the two other sensors. The derived results reveal the potential for monitoring bridge infrastructure. Finally, we propose further research aspects of this approach to analyse its capabilities and limitation in the context of non-invasive infrastructure monitoring.

Food-borne transmission is a recognized route for many viruses associated with gastrointestinal, hepatic or neurological diseases. Therefore, it is essential to identify new bioactive compounds with broad-spectrum antiviral activity is needed to exploit innovative solutions against these hazards. Lately, antimicrobial peptides (AMPs) have been recognized as promising antiviral agents. Indeed, while the antibacterial and antifungal effects of these molecules have been widely reported, their use as potential antiviral agents has not yet been fully investigated. Herein, the antiviral activity of previously identified or newly designed AMPs, was evaluated against the non-enveloped RNA viruses, Hepatitis A virus (HAV), and Murine Norovirus (MNV), a surrogate for human Norovirus. Moreover, specific assays were performed to recognize at which stage of the viral infection cycle the peptides could function. Results showed that almost all peptides displayed virucidal effects with about 90% of infectivity reduction on HAV or MNV. However, the decapeptide RiLK1 demonstrated, together with its antibacterial and antifungal properties, a notable reduction in viral infection for both HAV and MNV, possibly through direct interaction with viral particles or inhibition of the viral bonding to the cell receptors. Hence, RiLK1 could represent a versatile ‘antimicrobial agent effective against various foodborne pathogens including viruses, bacteria, and fungi.

Continuous glucose monitoring devices allow diabetes condition management. However, when limited data is available, one option is to increase their size by generating synthetic samples. From a homemade wearable prototype was created a real dataset with 18 instances and 53 attributes that capture characteristics of capillary and venous blood glucose, oxygen concentration, pulse rate, skin temperature, and 24 modules and 24 phases related to bio-impedance. The objective of this article is to generate synthetic datasets, and also it investigates the ideal features subset and optimal model for non-invasive diabetes prediction. Gaussian-Copulas (GC), conditional generative adversarial networks (CG), variational autoencoders, and Copula-GAN techniques' were used to generate five synthetic datasets. Experiments show that GC1 and GC2 datasets follow min/max boundaries and are not copies of the original data. Multilayer perceptron regressor outperformed (train and test) with 2.17, 2.51 in MAE; 9.29, 13.59 in MSE; 3.05, 3.69 in RMSE, and 0.95, 0.92 in R2 in GC1, and 2.64, 3.02 in MAE; 11.43, 15.11 in MSE; 3.38, 3.89 in RMSE, and 0.94, 0.92 in R2 in GC2 with eight features. Future work is necessary to explore autoencoder and generative architectures, datasets with diverse characteristics, and the effect of the number of features.

: Image guided superficial radiation therapy (IGSRT) combines superficial radiation therapy (SRT) with full dermal visualization (FDV) via high resolution dermal ultrasound (HRDUS) for the treatment of non-melanoma skin cancer (NMSC). The gold standard for IGSRT delivery includes a comprehensive cancer care model with support for the dermatologists by a multidisciplinary team. When delivered in this model, IGSRT can achieve cure rates of 99% for treatment of NMSC. This paper focuses on the benefits of IGSRT during therapy. Medical records from 7 dermatology clinics of 883 patients with 1,507 cases of NMSC treated with IGSRT be-tween 2017 and 2018 were retrospectively reviewed. 92% of the NMSC lesions showed daily depth fluctuations, 60.32% of lesions did not require changes during therapy, and nearly 40% of lesions required at least one compensatory change during therapy. 83% of NMSC lesions were labeled high-risk based on the 2024 NCCN guidelines. Increasing and decreasing tumor depth measurements during IGSRT inform dermatologists when adaptive changes in energy (kV), TDF and dose will result in more efficacy and less toxicity, respectively.

The presence of a non-structural protein 1 (NS1) in tick-borne encephalitis (TBE) vaccines and the possible induction of an NS1-specific immune response in vaccinated individuals remains a somewhat controversial topic. Previously, we detected the presence of NS1 in Encepur TBE vaccine by mass spectrometry and found the induction of NS1-specific IgG antibodies in mice vaccinated with FSME-Immun TBE vaccine. Here, in this follow-up study, we examined the dynamics and extent of the NS1-specific IgG response in mice vaccinated with these two vaccines in more detail and compared it with the IgG response to the whole virus (WV). Mice were vaccinated at two-week intervals with a total of six doses of each vaccine, and levels of IgG antibodies to TBE virus WV and NS1 were measured by ELISA after each dose. Both vaccines elicited a robust anti-WV IgG response after two doses. The Encepur vaccine did not elicit NS1-specific IgG even after all six doses. In contrast, FSME-Immun vaccine triggered production of NS1-specific IgG after four doses. The results indicate that FSME-Immun is the only vaccine that elicits an NS1-specific antibody response in mice. However, compared to WV-specific IgG, the NS1-specific response is weaker, and a higher number of doses is required to induce detectable levels of NS1-specific IgG antibodies.

Several traps are recommended for monitoring corn earworm, Helicoverpa zea (Boddie), an important pest of field, vegetable and fruit crops in the U.S. These traps, which are meant to capture H. zea in many cases end up capturing other insects. Helicoverpa zea has recently been found feeding on different seeds and dual-type (seed and fiber) hemp, Cannabis sativa L. (Rosales: Cannabaceae) causing serious damage. Limited work has been done on developing integrated pest management (IPM) for H. zea industrial hemp in Missouri. We evaluated the attractiveness of different traps with the aim of developing a monitoring system for the adult male H. zea in industrial hemp fields in two Missouri locations In addition, we recorded other non-target insects in the traps to determine trap selectivity. Commercially available green, clear, tricolor bucket traps Heliothis Scentry and Scentry Delta 1X traps baited with H. zea sex pheromones were evaluated in 2021 and 2022. Tricolor traps captured significantly more adult male H. zea than the other traps in both years. Non-target insects, mainly Xylocopa virginica (L.) (Hymenoptera: Apidae), Bombus spp (Hymenoptera: Apidae), and Apis mellifera L. (Hymenoptera: Apidae) were also captured. The tricolor trap captured the most bees. The presence of non-target species highlights the risk of using tricolor traps as a monitoring tool. This data provides information for planning the monitoring of corn earworm in industrial hemp farms in Missouri.