The effect of salinity on seed germination/emergence in narrow-leaved ash (Fraxinus angustifolia) was studied both under field and laboratory conditions, in order to detect critical values to NaCl exposure. Research Highlights: Novel statistical methods in germination ecology has been applied (i) to determine the effects of chilling length and salinity (up to 150 mM NaCl) on Fraxinus angustifolia subsp. oxycarpa seed emergence, and (ii) to estimate threshold limits treating germination response to salinity as a biomarker. Background and Objectives: Salinity cut values at germination stage had relevant interest for conservation and restoration aims of Mediterranean floodplain forests in coastal areas subjected to salt spray exposure and/or saline water introgression. Results: Salinity linearly decreased germination/emergence both in the field and laboratory tests. Absence of germination was observed at 70 mM NaCl in the field and at 150 mM NaCl for 4-week (but not for 24-week) chilling. At 50 mM NaCl germination percentage was 50% (or 80%) of control for 4-week (or 24- week) chilling. Critical values for salinity were estimated between freshwater and 50 (75) mM NaCl for 4-week (24-week) chilling by Bayesian analysis. After 7-week freshwater recovery, critical cut-off values included all tested salinity levels up to 150 mM NaCl, indicating a marked resumption of seedling emergence. Conclusions: Fraxinus angustifolia is able to germinate at low salinity and to tolerate temporarily moderate salinity conditions for about two months. Prolonged chilling widened salinity tolerance.

MicroRNAs (miRNAs) regulate plant growth and development and their responses to biotic and abiotic stresses. Although extensive studies show that miR159 family members regulate leaf and flower development in Arabidopsis thaliana, the roles of miRNAs in soybean (Glycine max) are poorly understood. Here, we identified six MIR159 genes in soybean, MIR159aMIR159f, and investigate their expression patterns in plants under low-phosphorus (low-P), NaCl, or abscisic acid (ABA) treatments. In soybean leaves, MIR159e and MIR159f expression was induced by low-P treatment, while in roots, MIR159b, MIR159c, MIR159e, and MIR159f expression was upregulated. In flowers, low-P led to upregulation of MIR159a, MIR159b, MIR159c, and MIR159f, but downregulation of MIR159d and MIR159e. In soybean nodules, MIR159b was upregulated but MIR159a, MIR159c, and MIR159d was downregulated under P deficiency. NaCl treatment induced MIR159a, MIR159b, MIR159c, and MIR159e expression in leaves, and MIR159aMIR159f expression in roots. ABA treatment upregulated MIR159a, MIR159b, and MIR159c but downregulated MIR159d, MIR159e, and MIR159f in leaves. These results suggest that miR159 family members function in plant abiotic stress responses. Moreover, total P content in leaves was significantly lower in plants overexpressing MIR159e than in the wild type, suggesting that miR159e may regulate P absorption and transport in soybean.

Salinity is the most significant abiotic stress affecting crop yield worldwide, breeders are Salinity is the most important abiotic stress limiting crop production throughout the world, and breeders are encouraged to test novel genotypes for their resistance to this selection agent. However, getting a sufficient number of plants for the evaluation can be a lengthy and time-consuming procedure that might be shortened by applying in vitro techniques. An experiment was conducted under controlled saline circumstances using a tissue culture technique to investigate the influence of salt on several physic-biochemical parameters. Micro-shoots of Volkamariana lemon, sour orange, trifoliate orange, and Cleopatra mandarin rootstocks were re-cultured on MS media supplemented with NaCl from 25, up to 150 mM. Following the experiments, all of the tested rootstocks' morphological and biochemical characteristics, stomata behavior, and element accumulation were measured. As a result, adding NaCl from 25 to 150 mM to MS media caused a reduction in all morphogenetic parameters such as shoot number, shoot length, leaves number, and survival percentage was measured compared with control. Photosynthesis pigment, RWC, K, and Ca ions were decreased by increasing NaCl from 100 to 150 mM. On the contrary, proline, Cl, and Na were increased. Cleopatra mandarin and Trifoliate orange are more tolerant to salt stress than Volkamariana lemon and sour orange citrus.

Salinity is a known factor which shapes population dynamics and community structure through direct and indirect effects towards aquatic ecosystems. The responses of Moina macrocopa (Cladocera) collected from Setiu Wetland lagoon (Terengganu) were evaluated through manipulative laboratory experiments to understand the ability of M. macrocopa to tolerate under high salinity stress. Specifically, the fatty acid composition, growth, survival and reproduction of this cladocerans species were examined. Sodium chloride (NaCl) were used in the treatments water with the concentration 0, 4, 6, 8, 12, and 15psu. Fatty acid levels were determined using Gas Chromatography and Mass Spectrophotometry (GC-MS). Results clearly indicate that normal conditions give the highest content of fatty acid, especially the polyunsaturated fatty acid content like EPA (eicosapentaenoic acid), ALA (alpha-linoleic acid), ARA (arachidonic acid) and DHA (docosahexaenoic acid). Furthermore, M. macrocopa survival also was best at 0psu, with percentage reached 98%, whereas the opposite occurred at 15psu, with approximately 9% of viable animals survived. On other aspects, M. macrocopa also showed the highest reproduction rate at 0psu (e.g. average initial age of reproduction, 4.33±0.58 days) compared with other salinities level. Interestingly, the difference in terms of growth at different salinities was unapparent, an unexpected outcome when adverse effects such as osmoregulation pressure on the organism are considered. Based on the results, we conclude that M. macrocopa can only tolerate salinity below 8psu and, is unable to withstand stressful environmental condition engendered with salinities above 8psu.

In this study, we investigated the inhibiting effect of Dioscorea spp leaf extracts on the corrosion of mild steel in selected media using the weight loss method. The mild steel samples were pre-weighed and immersed in NaOH, NaCl and H₂SO₄ solutions respectively containing the leaf extracts, with the control samples immersed in solutions of the media containing no extract. The samples were allowed to stand for 672 hours, with a set of samples from each environment withdrawn at intervals of 168 hours for corrosion characterization. The results obtained from all the environments indicate that the corrosion rate increased as concentrations of Dioscorea spp increased. Results also confirmed that the extract was an effective and excellent inhibitor in the alkaline, salt, and acidic media. Conclusively it was proven that the higher concentration of Dioscorea spp leaf extracts in the media had the best inhibition characteristic on the mild steel in the selected environments. The results show good potential for application in manufacturing industries. The microstructure analysis of the various test coupons in the test media should be carried out to reveal the influence of adding the leaf extracts to the stimulated media on the grain structure distribution of the mild steel.

Salinity substantially affects plant growth and crop productivity worldwide. Plants adopt several biochemical mechanisms including regulation of antioxidant biosynthesis to protect themselves against the toxic effects induced by the stress. One-year-old Pistachio rootstock exhibiting different degrees of salinity tolerance were subjected to sodium chloride induced salt stress to identify genetic diversity among cultivated pistachio rootstock for their antioxidant responses, and to determine the correlation of these enzymes to salinity stress. Leaves and roots were harvested following NaCl-induced stress. Results show that a higher concentration of NaCl treatment induced oxidative stress in the leaf tissue and to a lesser extent in the roots. Both tissues showed an increase in ascorbate peroxidase, superoxide dismutase, catalase, glutathione reductase, peroxidase and malondialdehyde. Responses of antioxidant enzymes were cultivar dependent, as well as temporal and dependent on the salinity level. Linear and quadratic regression model analysis revealed significant correlation of enzyme activities to salinity treatment in both tissues. The variation in salinity tolerance reflected their capabilities in orchestrating antioxidant enzymes at the roots and harmonized across the cell membranes of the leaves. The study provides a better understanding of root and leaf coordination in regulating the antioxidant enzymes to NaCl induced oxidative stress.

The silane (3-Aminopropyl)triethoxysilane (APTES), possesses one terminal amine group and three ethoxy groups extending from each silicon atom, serving as a crucial interface adherent between organic and inorganic materials. In corrosion prevention, APTES is frequently employed as a primer, with subsequent topcoat as an extra protective layer. This topcoat is particularly useful in covering sites where APTES may exhibit poor bonding, such as those involving Cu or Cu-rich alloying elements. In our study, we applied a thin layer of APTES to cleaned AA2024-T3 samples using concentrated vapor deposition, followed by spin-coating with a diluted PS/acetone solution. Through combinatorial experimentation, we investigated the impact of APTES on the corrosion resistance of the coating system on AA2024-T3. Our findings indicate that a higher surface energy of the APTES primer contributes to better corrosion resistance in the overall coating system. This improvement can be attributed to enhanced wettability achieved by the PS/acetone solution on the cured APTES primer, leading to a more uniform coverage of the dried PS topcoat. Additionally, our research revealed that, in the early stages of exposure to the corrosion solution, a thinner APTES primer enhances protection against corrosion. This effect is attributed to hydrolytic stability mechanisms, and the interactions between hydrolyzation/condensation in soaked APTES and the dissolution of naturally formed aluminum oxide pre-existing in the bare samples. Finally, we observed that an APTES primer subjected to additional heat treatment before topcoating exhibits superior performance in corrosion resistance.

As sessile organisms, plants face a wide range of abiotic stresses, with salinity being a prominent constraint affecting their growth, development, and productivity, particularly in arid and semi-arid regions. This study focused on understanding how salinity impacts Jatropha curcas, an important oilseed plant for biodiesel production. By examining the anatomy and ultrastructure of stomata and chloroplasts, we investigated the effects of prolonged salinity stress on J. curcas. This stress led to changes in stomatal density, stomatal index, and ostiole aperture, which case an imbalance of water conductivity in the xylem. Through transmission electron microscopy, we explored the subcellular organization of J. curcas chloroplasts and their contribution to plant photosynthetic efficiency, providing insights into their role in this process. Notably, salinity treatment resulted in a significant increase in starch granules accumulation, leading to impaired the granal and stromal grana lamellae, destroying this ultrastructure. Our findings indicate that the anatomy and ultrastructure of chloroplasts play a crucial role in influencing photosynthetic efficiency and hydraulic conductivity. This study offers new perspectives on the structure and function of chloroplasts in J. curcas, presenting innovative opportunities to develop strategies that enhance biofuel production in areas with high soil salinity.

Two pilot scale desalination system employing carbon modified nano-sized, zero valent metals (n-ZVM) were maufactured and tested to determine (1) the degree to which high salt water (20 to 130 mS) could be desalinated and (2) if this degree of desalination could be maintained throughout an extended treatment period. Two pilot systems were tested (referred to as Generation 1 and Generation 2) consisting of parallel lines of 4 individual reactors in series, a settling tank and an activated carbon cell at the end of each reactor line. The system capacity was 300 gal in Generation 1 and 600 gal in Generation 2 total with a total hydraulic residence time of 6 hours per reactor line (one hour per cell/tank). A slurry of n-ZVM was introduced in the first reactor on each line to yield approximately 5 to 45 grams of nano-metal per 100 L of influent salt water. The n-ZVM slurry was made from mixing tea extract with metal salts (eg ferrous sulfate, ferric chloride) to produce the carbon modified metal slurry. Initial runs focused on dosing required to achieve maximum salt removal at each of three influent salt contents, 28 mS, 44 mS and 123 mS. Once dosing was set, continuous runs (14 days, 23 days and 9 days) were carried out to (1) examine the ability of the pilot to maintain the removal efficiency over an extended period, (2) to determine the weaknesses inherent in the pilot systems, and (3) to begin to develop CAPEX and OPEX estimates for the pilot and pre-design full scale mobile desalination unit (MDU) system. Results demonstrated that maximum removal occurred with 10 g/100L of salt for the 30 mS salt solution,16 g/100 L of salt for the 40 mS influent water and 40 g/100 L for the 130 mS influent. Salt removal (expressed as Na and Cl removed) approached 78% for the 30 mS influent and 41 mS influent respectively while removal for the highest salt influent (130 mS) approached 81 %. Addition of greater amounts of carbon modified slurry than those described resulted in a pH less than 6 which inhibits continued salt removal and would require addition of calcium or magnesium oxides/hydroxides or bicarbonate solutions at the influent side to achieve greater salt removal and of course greater cost per gallon. Continuous operation over the extended time-period showed no significant decrease in salt removal with typical day to day variation of no more than 10% suggesting that this approach to desalination could rapidly provide usable water from saline aquifers, seawater or even produced water. Treatment of saline waters at 30 mS or less yields effluent water in the range necessary for irrigation use of many crops while treatment of seawater or produced water levels of salt (40 mS or higher) yields effluent in the range of 8 to 10 mS a range ideal for RO influent that would prevent the production of large volumes of brine. Pilot testing continues with seawater extracted from Puget Sound, Seattle WA and higher levels of salt to better represent produced water.

Helmholtz energy of ice VII-X is determined in a pressure regime extending to 450 GPa at 300 K using local basis functions in the form of b splines. The new representation for the equation of state is embedded in a physics-based inverse theory framework of parameter estimation. Selected pressures as a function of volume from 14 prior experimental studies and two theoretical studies constrain the behavior of Helmholtz energy. Separately measured bulk moduli, not used to construct the representation, are accurately replicated below about 20 GPa and above 60 GPa. In the intermediate range of pressure, the experimentally determined moduli are larger and have greater scatter than values predicted using the Helmholtz representation. Although systematic experimental error in the experimental elastic moduli is possible and likely, the alternative hypothesis is a slow relaxation time associated with changes in proton mobility or the ice VII to X transition. A correlation is observed between anomalies in the pressure derivative of the predicted bulk modulus and previously suggested higher-order phase transitions. Improved determinations of elastic properties at high pressure would allow refinement of the current equation of state. More generally, the current method of data assimilation is broadly applicable to other materials in high-pressure studies.

Parasite control strategies such as blanket anthelmintic treatment of all horses in a herd or interval treatment regimen based on egg reappearance remain widely followed practices for the last several decades. These practices have resulted in the fast emergence of resistance in equine strongyles to all major classes of drugs on the market. In this regard, the guidelines set by the American Association of Equine Practitioners advocate evidence-based strongyle control in horses. It recommends targeted treatment of all heavy egg shedders [> 500 eggs per gram (EPG) of feces] while the low shedders (0-200 EPG) are left untreated to maintain susceptible parasite refugia in a herd. As 50-75% of adult horses in a herd are low shedders, preventing them from unnecessary anthelmintic exposure is critical to tackling resistance. There are various fecal egg count (FEC) techniques with many modifications and variations in use, but none is identified as a gold standard and methods comparison studies are lacking. We hypothesized that the diagnostic performance of commonly used quantitation methodologies differs and the FEC methods must be evaluated to determine the gold standard. In this regard, we performed methods comparison studies using polystyrene beads with size and specific gravity comparable to strongyle eggs, as proxy. The linearity of 12 commonly used FEC methodologies (3 techniques with 4 different solutions) was studied using bead standards in the clinically applicable range (63 to 1,000) to determine their suitability for strongyle egg counts. Deming regression analysis identified Mini-FLOTAC with sugar (specific gravity 1.33) as the test with the greatest coefficient of determination. All tests underestimated the true bead count, and we determined a correction factor (CF) for each test to estimate the true count. CF negates the preference for a gold standard test. Finally, we analyzed the validity of CF for 5 tests with R2>0.95 to accurately quantify strongyle eggs from 40 different horses. Overall, this study identified methodologies with the highest diagnostic performance and the limitations to standardizing routine FEC tests to promote uniformity in implementing AAEP parasite control guidelines.