In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

Changing the film thickness to manipulate the microstructural properties has been considered as a potential method in practical application. Here, we report that atomic-scale structural properties regulated by film thickness in NiCO2O4(NCO)/CuFe2O4(CFO) bilayer heterostructure prepared on (001)-MgAl2O4 (MAO) substrate by means of aberration-corrected scanning transmission electron microscopy (STEM). The misfit dislocations at NCO/CFO interface and antiphase boundaries (APBs) bound to dislocations within the films both are found in NCO (40 nm)/CFO (40 nm)/MAO heterostructure to contribute to relaxation of mismatch lattice strain. In addition, the non-overlapping a/4[101]-APB is found and the structural transformation of this kind of APB is resolved at atomic scale. In contrast, only the interfacial dislocations form at interface without the formation of APBs within the films in NCO (10 nm)/CFO (40 nm)/MAO heterostructure. Our results provide evidence that formation of microstructural defects can be regulated by changing film thickness to tune magnetic properties of epitaxial bilayer spinel oxide films.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s-1 under fixed strain conditions. However, many existing constitutive models either fail to capture the mechanical characteristics of this plastic deformation or use piecewise strain rate hardening models to describe this phenomenon. Unfortunately, the piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggling to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semi-empirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari-Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain rate sensitivity under fixed strain, particularly evident in the annealed OFHC. The predicted results of the model across a wide range of strain rates (10-4 − 106 s-1) and temperatures (77 − 1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared to five other models, including Mechanical Threshold Stress (MTS), Nemat-Nasser-Li (NNL), Preston-Tonks-Wallace (PTW), Johnson-Cook (JC), and Molinari-Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.

A La2FeCrO6 (LFCO) double perovskite powders were synthesized by hydrothermal method, which crystallized in an orthorhombic (Pnma) structure and exhibited a spherical morphology with average particle size of 900 nm. Fourier transformation infrared spectroscopy confirmed the octahedral coordination of Fe and Cr ions in the powders. XPS spectra revealed dual oxide states of Fe (Fe2+/Fe3+) and Cr (Cr3+/Cr4+) elements, and oxygen element appeared as lattice oxygen and defect oxygen, respectively. The LFCO powders exhibit ferromagnetic behavior at 5 K with saturation magnetization of 0.31 μB/f.u., coercive field of 8.0 kOe, and Curie temperature of 200 K. Griffiths phase appeared in the powders between 200 K and 223 K. The LFCO ceramics displayed a butterfly-like magnetoresistance (MR)-magnetic field (H) curve at 5 K with MR (5 K, 6 T) value of -4.07%. Temperature dependence of resistivity of the LFCO ceramics demonstrated their semiconducting nature. Electrical transport data were fitted by different conduction models. Strong frequency dispersion dielectric behavior was observed in the LFCO ceramics. A dielectric abnormality observed around 260 K, was ascribed to the jumping of electrons trapped in shallow levels created by oxygen vacancies. The dielectric relaxation behavior exhibited by dielectric loss between 160 K and 260 K, was contributed to the singly-ionized oxygen vacancies.

The present decade has witnessed numerous investigations focussed on the determination of the mechanical properties of Fly ash composites. These composites have attracted attention, especially in the form of reinforcements owing to their excellent tensile and compressive properties coupled with impact and hardness response. A number of techniques viz. in-situ deposition, hand-up lay and compo-casting techniques have been reported to fabricate these composites. However, in the context of these composites, a systematic structure-property correlation has not been established till date. The present review is aimed at highlighting the current state of research in the avenue of Fly ash composites from two different viewpoints, viz. (i) fabrication technique and (ii) mechanical properties of the fabricated composites. Moreover, the necessity of establishing systematic structure-property correlation in these materials has also been briefly discussed from the author’s viewpoint.

This study investigates the contribution of nano-alumina (nA: 1-3wt.% binder) to the performance of silica fume (SF-10%) blended mortar in ternary blended mortar. The fresh (workability, setting time) and hardened properties (compressive strength and thermal resistance (300 °C for 1 h)), were examined. Nano alumina (nA) contributed positively to the consistency of SF blended mortar such that similar workability could be achieved with OPC when 3% nA was added. The initial and final setting time of 180 and 220 mins were recorded in SF blended mortar and reduced by 18.4 and 21.8%, respectively by adding 3%nA. The optimum mixture that contained 10%SF and 2%nA had 3-d and 28-d compressive strengths of 28 and 43.2 MPa. In the absence of nA, this reduced by 14.3% and 29.4% while it reduced by 25.2% and 16.7%, respectively in OPC mortar. The main products characterizing SF-nA ternary blended binder with dense microstructural density were nepheline and tobermorite. Besides, it is more susceptible to carbonation despite its superior performance in thermal resistance when compared to SF blended and OPC mortars.

Finely ground glass has the potential for pozzolanic reactivity and can serve as a supplementary cementitious material (SCM). Glass reaction kinetics depends on both temperature and glass composition. Microstructural modeling is a helpful approach to get better understanding of cement hydration and microstructure development. Mechanical and performance properties of concrete are directly related to the development of concrete microstructure, which is the consequence of progress in cement hydration. This study initially provides a comprehensive background about cement hydration process and microstructural modeling of the hydration. It then utilizes results of experimental studies, i.e. isothermal calorimetry and thermogravimetric analysis, to find kinetics equation parameters called “Avrami Constants”. For the first time, these constants were found for three main components of cement, i.e. C₃S, C₂S, and C₃A, and also for glass particles smaller than 25 µm. Although modeling of cement hydration and cementitious systems containing single glass particles showed promising results, simulations of combined glass types and sizes showed that more work on microstructural models is needed to properly model the reactivity of mixed glass particle systems.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

This research presents a comprehensive bibliometric and sentiment analysis of nanocomposite literature from 1990 to 2024. Employing cutting-edge computational methods, the study delves deep into the progression of microstructural characterization, electrical properties, and mechanical behaviors of nanocomposites. The analysis utilizes advanced Boolean search strategies from the Scopus database, ensuring a thorough extraction of thematic content. The results explore various themes and insights, shedding light on trends evident in the Scopus database, particularly the prominence of research on nanocomposite microstructure, electrical attributes, and mechanical performance. The paper also offers textual analytics and bibliometric data, showcasing critical collaborative efforts and influential studies. Significant discoveries encompass the evolution of research language, shifts in thematic focus, and global contributions, providing a comprehensive perspective on the current landscape of nanocomposite research and its dynamic evolution. Moving forward, the "State-of-the-Art and Gaps Extracted from Results and Discussions" section of the paper delves into the most recent advancements in nanocomposite research. It delves into various types of nanocomposites, with a particular emphasis on their microstructural characteristics, electrical properties, mechanical dynamics, and the application of nanocomposite films. This section identifies key research themes, traces historical progress, and highlights emerging trends while underscoring the significance of collaboration and the influence of pivotal studies that have shaped the field. Lastly, in the "Literature Review Guided by Artificial Intelligence" section, the paper introduces a revised approach for researching nanocomposites through AI-guided techniques. This approach prioritizes articles published in 2023 based on citation frequency. Here, the focus is on exploring the relationship between nanocomposites and their electrical properties, emphasizing their fundamental interactions and impact on electrical characteristics. Various nanocomposite systems are covered, highlighting their composition, structure, and functionality. Findings from recent studies are integrated to provide a comprehensive overview of the current state of knowledge in this area. Notably, the sentiment analysis, anchored by an average sentiment score of 0.638771, underscores a positive trajectory in academic discourse, emphasizing the growing recognition of the potential of nanocomposites. The bibliometric exploration maps the intellectual domain, emphasizing pivotal research themes and the influence of crosslinking time on nanocomposite attributes. While this study is thorough, it acknowledges its limitations and advocates for broader database inclusion in future research endeavors. This work elucidates the prevailing trends in nanocomposite research, emphasizing the indispensable role of computational tools in comprehending this vast wealth of information.

Solidification microstructure is formed under high cooling rates and temperature gradients in powder-based additive manufacturing. In this study, a non-equilibrium multi-phase field method (MPFM), which was based on a finite interface dissipation model proposed by Steinbach et. al., coupled with a CALPHAD database was developed for a multicomponent Ni alloy. A qua-si-equilibrium MPFM was also developed for comparison. Two-dimensional equiaxed micro-structural evolution for the Ni (Bal.)–Al–Co–Cr–Mo–Ta–Ti–W–C alloy was performed at various cooling rates. The temperature–γ fraction profiles obtained under 10^5 K/s using non- and qua-si-equilibrium MPFMs were in good agreement with each other. Over 10^6 K/s, the differences between non- and quasi-equilibrium methods grew as the cooling rate increased. The non-equilibrium solidification was strengthened over a cooling rate of 10^6 K/s. Colum-nar-solidification microstructural evolution was performed under cooling rates from 5×10^5 K/s to 1×10^7 K/s at various temperature gradient values under the constant interface velocity (0.1 m/s). The results showed that as the cooling rate increased, the cell space decreased in both methods, and the non-equilibrium MPFM agreed well with experimental measurements. Our results show that the non-equilibrium MPFM can simulate solidification microstructure in powder bed fusion additive manufacturing.

: Sputtering of silicon in a Helium magnetron discharge (MS) has been reported as a bottom-up procedure to obtain He-charged silicon films (i.e. He nanobubbles encapsulated in a silicon matrix). The incorporation of heavier noble gases is demonstrated in this work with a synergistic effect producing increased Ne and Ar incorporations when using He-Ne and He-Ar gas mixtures in the MS process. Microstructural and chemical characterizations are reported by ion beam analysis (IBA) and scanning and transmission electron microscopies (SEM and TEM). In addition to gas incorporation, helium promotes the formation of larger nanobubbles. For the case of Ne high resolution X-ray photoelectron and absorption spectroscopies (XPS and XAS) are reported with remarkable dependence of the Ne 1s photoemission and the Ne K-edge absorption on the nanobubbles size and composition. The gas (He, Ne, Ar) charged thin films are proposed as “solid” targets for the characterization of spectroscopic properties of noble gases in a confined state without the need for cryogenics or high-pressure anvils devices. Also their use as targets for nuclear reaction studies is foreseen.