Cellulose-based carbon (CBC) has been widely concerned with its porous structure, high specific surface area, and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, ZnO/CBC heterojunction was formed by means of simple co-precipitation and high temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia compared with that of the previous pure ZnO ammonia sensor can not at room temperature. It has great gas sensing response, stability and selectivity to ammonia concentration at 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

This research aimed to determine the effect of alkaline treatment on zalacca midrib fiber (ZMF) concerning various aspects such as thermal stability, crystallinity index, interfacial bonding, interfacial shear strength, water absorption capacity, as well as conducting Scanning Electron Microscopy (SEM). This investigation extended to evaluating the mechanical properties of composites enriched with microcrystalline cellulose with prosthetic socket materials available on the market. Subsequently, ZMF was obtained by splitting and soaking zalacca midrib for 12 hours. Each of ZMF was removed from the midrib and soaked in 5% sodium hydroxide for 3, 6, 9, and 12 hours. The composite material was molded by mixing 10% microcrystalline cellulose with a rotational speed of 150 rpm, maintaining a temperature of 40°C, and continuing the mixing process for 30 minutes. As a result of the alkaline treatment, several positive effects were observed, including increased fiber density, improved particle bonding, increased thermal compatibility, and cleaner fiber surfaces, attributed to reduced levels of hemicellulose, lignin, pectin, and other impurities as confirmed by SEM analysis. The microcrystalline cellulose added to the composite increased the interfacial shear strength, and tensile strength increased by 56.74%, composite flexural strength increased by 76.43%. The SEM analysis results showed that the composite with ZMF on the base fiber broke during the tensile test because fiber experienced an increase in interfacial bonding between fiber and the matrix. The water absorption test showed that untreated fiber had a higher level of absorption

This manuscript presents the result of utilizing cellulose as a template to prepare na-nosized WO3-NiWO4 and its application as co-catalysts in Pt/WO3-C and Pt/WO3-NiWO4-C for ethanol and glycerol electro-oxidation. Microcrystalline cellulose was hydrolyzed with phosphotungstic acid (H3PW12O40) to prepare the nanosized template of crystalline cellulose. Next, the template was impregnated with Ni(NO3)2, rendering a precursor mate-rial that is subsequently air-calcinated, removing the carbon-template material to obtain the nanometric WO3 and NiWO4. Elemental analysis confirmed the coexistence of nickel and tungsten, whereas the thermal analysis evidenced the high thermal stability of these materials. The X-ray diffractograms displayed crystal facets of WO3 and, when added Ni, of NiWO4. The transmission electron micrographs corroborated the formation of na-nosized particles with average particle sizes close to 50 nm. Finally, to apply this material, Pt/WO3-C and Pt/WO3-NiWO4-C were prepared and used in ethanol and glycerol electro-oxidation in alkaline medium, observing a promotional effect of the oxide and tungstate by reducing the onset potential and increasing the current density. These materials show great potential to produce clean electricity or green hydrogen contributing to energetic transition.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

The mortar’s composition, porosity, mechanical properties, entryways’ orientation, and condi-tioning status of the tunnels made by the Najdian Termite, Microtermes najdensis located at Hada Al-Sham village, Makkah Province, Saudi Arabia were studied. The most prevalent infected tim-ber trees by this pest were Tamarix aphylla, Pithecellobium duce, Zizyphus spina christi, Leucaena leu-cocephala, Ficus infectoria, and Phoenix dactylifera. Climate, soil, healthy wood (Wh), and termite nest skeleton (TNS) were the four components of the termite system that were investigated physi-cally, chemically, spectroscopically, and by FTIR, XRD, SEM, and TEM. It was noticed that the entryways of the termite nests are located at the southwest direction for all the infected trees studied at Hada Al-Sham village that promotes better ventilation. Concerning to the air-conditioning status within the their nest, the internal temperature (IT) was found to be milder than that for its analogous value for the outer temperature (OT) in which the IT was wormer than OT during cold durations, while it was colder than the hottest OT in hot days and vice versa. The IT’s trend had more constantancy with minor fluctuations compared to that for the OT. Moreo-ver, the IT was found to be tended to the upper OT’s limit otherwise its colder one. This finding means that these termite species prefer the hotter atmospheres comparing the colder circumstanc-es. Lignin is the prominent tracer of the organic matter used as a binder for the TNS due to its gluing ability, resistance to enzymatic degradation by the termites and their accompanied fungal community habituating the nests. The presence of both microcrystalline cellulose (MCC) and nanocrystalline cellulose (NCC) was discovered for the first time in the nest mortar reinforcing Klason lignin as the main binder. Their presence was proved by FTIR, XRD, SEM and TEM anal-yses and we satisfied that they were naturally-synthesized by the action of enzymatic hydrolysis excreted by the termites and their accompanied fungal community habituating the nests. The gross heat of combustion (GHCs) of the Wh and TNS were studied to try to find an important uti-lization of the infected woods as renewable energy resources instead of disposal them without economic benefits. These findings may be used for interpreting the durability of the termite nests to the different environmental stresses. Biomimicry of the termites’ nest from the perspective of its magic mortar with a suitable permeability, the entryways’ orientation, and the air-conditioning status can lead to modify the current construction’s designs to be more green and ecofriendly.