High-resolution wave measurements at intermediate water depth are required to improve coastal impact modeling. Specifically, such data sets are desired to calibrate and validate models, and broaden the insight on the boundary conditions that force models. Here, we present a wave data set collected in the North Sea at three stations in intermediate water depth (6-14~m) during the 2021/2022 storm season as part of the RealDune/REFLEX experiments. Continuous measurements of synchronized surface elevation, velocity and pressure were recorded at 2-4~Hz by Acoustic Doppler Profilers and an Acoustic Doppler Velocimeter for a 5~month duration. Time series were quality-controlled, directional-frequency energy spectra were calculated, and common bulk parameters were derived. Measured wave conditions vary from calm to energetic with 0.1-5.0~m sea-swell wave height, 5-16~s mean wave period and W-NNW direction. Nine storms, i.e. wave height beyond 2.5~m for at least six hours, were recorded including the triple storms Dudley, Eunice and Franklin. This unique data set can be used to investigate wave transformation, wave nonlinearity and wave directionality for higher and lower frequencies (e.g. sea-swell and infragravity waves) to compare with theoretical and empirical descriptions. Furthermore, the data can serve to force, calibrate and validate models during storm conditions.

In this work, we propose a method to measure planar temperature fields of fluids flow. We used a focusing schlieren technique together with a calibration procedure to fulfill such purpose. The focusing schlieren technique uses an off-axis circular illumination to reduce the depth of focus of the optical system. The calibration procedure is based on the relation of the intensity level of each pixel of a focused schlieren image to the corresponding cutoff grid position measured at the exit focal plane of the schlieren lens. The method is applied to measure planar temperature fields of the hot air issuing from a 10 mm diameter nozzle of a commercial Hot Air Gun Soldering Station Welding. Our tests are carried out at different temperature values and different planes along the radial position of the nozzle of the Hot Air Gun Soldering Station Welding. The temperature values obtained experimentally are in agreed with those obtained with a thermocouple.

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

Virtual validation of radar sensor models is becoming increasingly important for the safety validation of adf. Therefore, methods for quantitative comparison of radar measurements in the context of model validation need to be developed. This paper presents a novel methodology for accessing and quantifying validation measurements of radar sensor models. This method uses edf and the so-called dvm to effectively quantify deviations between distributions. By applying this metric, the study measures the consistency, reproducibility and repeatability of radar sensor measurements. Different interfaces and different levels of detail are investigated. By comparing the radar signals from real world experiments where different objects are present, valuable insights are gained into the performance of the sensor. In particular, the research extends to assessing the impact of varying rain intensities on the measurement results, providing a comprehensive understanding of the sensor’s behaviour under these conditions. This holistic approach significantly advances the evaluation of radar sensor capabilities and enables the quantification of the maximum required quality of radar simulation models.

From December 2021 to May 2022, MeteoSwiss and Meteomatics conducted a proof of concept to demonstrate the capability of Meteodrones to provide data of sufficient quality and reliability on a routine operational basis. Over 6 months, Meteodrones MM-670 were operated automati-cally 8 times per night at Payerne, Switzerland. 864 meteorological profiles were measured and compared to co-located standard measurements including radiosoundings and remote-sensing instruments. To our knowledge, it is the first time that Meteodrone’s atmospheric profiles are evaluated in such an extensive campaign. The paper highlights two case studies that showcase the performance and challenges of measur-ing temperature, humidity, and wind with a Meteodrone. It also focuses on the overall quality of the drone measurements. Throughout the campaign, the availability of Meteodrone measure-ments was 75.7%, with 82.2% of the flights reaching the nominal altitude of 2000m above sea level. To assess the quality of the Meteodrone measurements, the radiosondes were used as a refer-ence, comparing them to the WMO (World Meteorological Organization) requirements [1]. The temperature measurements by the Meteodrone met the "breakthrough" target, while the humid-ity and wind profiles met the "threshold" target for high-resolution numerical weather predic-tion. The temperature measurement quality was comparable to that of a microwave radiometer, and the humidity quality was similar to that obtained from a Raman Lidar. However, the wind measurements by a Doppler Lidar were more accurate than the estimation provided by the Me-teodrone. During this campaign, the data quality could be improved and at the end of the campaign, Me-teodrone quality reached the “goal” target for temperature and the “breakthrough” target for humidity. This campaign marks a significant step towards the operational use of automatic drones for me-teorological applications.

The details of ac-conductivity measurements in a colloidal electrolyte cell with flat control gate electrodes are discussed. The use of impedance diagnostics in studies of transport phenomena in such systems requires caution in the definition of the thickness of the screening accumulation layers that appear along the metal-electrolyte interfaces. The value of this characteristic length λ0 critically depends on the volume fraction ϕ⊙ of colloidal particles in the bulk of electrolyte. Accounting for the dependence λ0(ϕ⊙) makes it possible to consistently explain the large discrepancy in the available experimental data regarding the influence of colloidal fraction on the effective conductivity of the colloidal suspension.

In many application problems, F-transform algorithms are very efficient. In F-transform techniques, we replace the original signal or image with a finite number of weighted averages. The use of weighted average can be naturally explained, e.g., by the fact that this is what we get anyway when we measure the signal. However, most successful applications of F-transform have an additional not-so-easy-to-explain feature: the partition requirement, that the sum of all the related weighting functions is a constant. In this paper, we show that this seemingly difficult-to-explain requirement can also be naturally explained in signal-measuring terms: namely, this requirement can be derived from the natural desire to have all the signal values at different moments of time estimated with the same accuracy.

The use of several light-related variables, such as the Secchi disc depth, the euphotic depth, and in particular, the diffuse attenuation coefficient (Kd), is deeply rooted in phytoplankton research, but these are not the most appropriate indicators of the amount of light available for photosynthesis. We argue that the variable of interest for phytoplankton is the mean light intensity in the mixed layer (Im), which represents the mean light to which phytoplankton cells are exposed throughout their life cycle, while being continuously mixed in the mixed layer. We use empirical data collected in different coastal ecosystems in southern Portugal to demonstrate why Im should be the preferred metric instead of the deeply rooted Kd. We show that, although the relationship between Im and Kd is inversely proportional, it is not always strong or even significant. Different Im values can be associated to the same Kd, but distinct Im have different physiological effects of phytoplankton. Therefore, Kd does not capture the amount of light available for photosynthesis, given that, unlike Im, Kd calculation does not consider the depth of the mixed layer. Therefore, we urge phytoplankton researchers to consider the measurement and calculation of Im when evaluating light-related processes in phytoplankton ecology.

With the continual global increase of PV power systems and the inherent weather-induced volatility of their power output, understanding the underlying variability of solar radiation in both space and time is important for the planning and reliable operation of future power grids. This paper concisely reviews recent advances in the characterization of irradiance variability with an emphasis on small spatial and temporal scales (respectively less than about 10\,km and 1\,min), for which comprehensive data sets are time consuming and expensive to collect, and although needed have not been available until recently. Special attention is given to studies dealing with the quantification of variability using such unique data, the analysis and modeling of spatial smoothing, and the evaluation of temporal averaging.

Recent researches proved that the underbridge geometry can be reconstructed by mounting a 3D laser scanner on a motorized cart travelling on a walkway located under the bridge. The walkway is moved by a truck and the accuracy of the bridge model depends on the accuracy of the trajectory of the scanning head with respect to a fixed reference system. In this paper, we describe the metrological characterization of a method that uses non-contact systems to identify the relative motion of the cart with respect to the walkway; the orientation of the walkway with respect to the bridge is determined using inclinometers and optical rails, while the position of the truck with respect to the bridge is measured using a conventional odometer. The measurement uncertainty of the proposed system was initially evaluated by numerical simulations and successively verified by experiments in laboratory conditions. The complete system has then been tested in operative conditions; the validity of the proposed approach has been demonstrated by comparing the geometry of buildings reconstructed with the proposed system with the geometry obtained with a static scan. Results evidenced that the errors are approximately 6 mm.

Background: The association of echocardiographic findings and subsequent risk of left-sided native valve endocarditis (LS-NVE) is undefined. The aim of this study was to determine if transthoracic echocardiographic (TTE) measurements are associated with the subsequent development of LS-NVE in patients without cardiac predisposing conditions. Methods: Institutional databases were evaluated for adults diagnosed with LS-NVE from 2008 to 2020. Patients with prosthetic valves, cardiovascular implantable electronic devices, intracardiac devices, injection drug use, and predisposing cardiac conditions were excluded. Only patients who had a TTE performed 6 months to 3 years before the development of LS-NVE were included as cases. Controls were patients within the same Mayo location with a TTE report and were matched in a 1:3 ratio according to age, gender, Charlson Comorbidity Index, and echocardiography date. Results: There were 148 cases and 431 matched controls. As compared to controls, IE cases had a higher prevalence of diabetes mellitus (46.6% vs. 30.4%) and chronic kidney disease (46.6% vs. 28.1%) (p<0.001). Left ventricular outflow tract velocity (p=0.017), left ventricular ejection fraction (p=0.018), and E: e’ ratio (p=0.050) were associated with LS-NVE. Conclusions: Echocardiographic measurements were associated with subsequent LS-NVE development in this pilot study. A larger cohort of LS-NVE patients, however, is needed to validate these findings.

This study concerns in to collect, via a systematic review, works from international academics that employed bicycles to collect primary data on environmental variables for research on microclimatic thermal problems in urban contexts. To that purpose, a systematic review was con-ducted employing several important processes that favor the collecting of relevant material from three well-regarded worldwide academic platforms using well-defined keywords. A selection of papers identified through the platforms was produced, and after reading the titles, abstracts, and entire works, 13 articles were collected that employed bicycles in their mobile transects between 2011 and 2023. The analytical methodologies connected to the thermal environment employed by the research, such as the primary characterizers of urban morphology, were visible from this. The systematic review showed effective in attempting to comprehend current research in the scientific community that employed the approach of mobile measurements using bicycles. The great bulk of work was done in the Northern Hemisphere, specifically on the European continent. Furthermore, it was discovered that the number of publications published using this approach has increased in the previous two years. It is worth emphasizing that, while the platforms offer outstanding results in terms of article discovery, we are nevertheless aware of additional publications that employed similar technique but did not appear in the platforms' results. More study utilizing the bicycle is anticipated for, so that the process may be improved and the precision of future results can be reached.

Measuring Marginal Reflex Distance-1 (MRD-1) is a crucial clinical tool used to evaluate the position of the eyelid margin in relation to the cornea. Traditionally, this assessment has been conducted manually by plastic surgeons, ophthalmologists, or trained technicians. However, with the advancements in Artificial Intelligence (AI) technology, there is a growing interest in the development of automated systems capable of accurately measuring MRD-1.In this context, we introduce novel MRD-1 measurement methods based on deep learning algorithms that can simultaneously capture images and compute the results. This prospective observational study involved 154 eyes of 77 patients aged over 18 years who visited Chungnam National University Hospital between September 1, 2023, and July 29, 2023. We collected four different MRD1 da-tasets from patients using three distinct measurement methods, each tailored to the individual patient. The mean MRD1 values, measured through the manual method using a penlight, the deep learning method, ImageJ analysis from RGB eye images, and ImageJ analysis from IR eye images in 56 eyes of 28 patients, were 2.64 ± 1.04 mm, 2.85 ± 1.07 mm, 2.78 ± 1.08 mm, and 3.07 ± 0.95 mm, respectively. Notably, the strongest agreement was observed between MRD1_deep learning (DL) and MRD1_IR (0.822, p < 0.01). In the Bland-Altman plot, the smallest difference was observed between MRD1_DL and MRD1_IR ImageJ, with a mean difference of 0.0611 and △LOA (limits of agreement) of 2.5162, which is the smallest among the other groups. In conclusion, this novel MRD1 measurement method, based on an IR camera and deep learning, demon-strates statistical significance and can be readily applied in clinical settings.

In microwave imaging it is often of interest to inspect electrically large spatial regions. In these cases, data must be collected over a great deal of measurement points which entails long measurement time and/or costly, and often unfeasible, measurement configurations. In order to counteract such drawbacks, we have recently introduced a microwave imaging algorithm which looks for the scattering targets in terms of equivalent surface currents supported over a given reference plane. While this method is suited to detect shallowly buried targets, it allows to independently process each frequency data, hence the source and the receivers do not need to be synchronized. Moreover, spatial data can be reduced at large extent, without incurring in aliasing artefacts, by properly combining single-frequency reconstructions. In this paper, we validate such an approach by experimental measurements. In particular, the experimental test site consists of a sand box in open air where metallic plate targets are shallowly buried (few cm) under the air/soil interface. The investigated region is illuminated by a fixed transmitting horn antenna whereas the scattered field is collected over a planar measurement aperture at a fixed height from the air-sand interface. The transmitter and the receiver share only the working frequency information. Experimental results confirm the feasibility of the method.

The corrosion inhibition performance of pyridine derivatives (4-methylpyridine and its quaternary ammonium salts) and sulfur-containing compounds (thiourea and mercaptoethanol) with different molar ratios on carbon steel in CO2-saturated 3.5 wt.% NaCl solution was investigated by weight loss, potentiodynamic polarization, electrochemical impedance spectroscopy and scanning electron microscopy. The synergistic corrosion inhibition mechanism of mixed inhibitors was elucidated by the theoretical calculation and simulation. The molecule of pyridine derivatives compound with larger volume has the priority to adsorb on the metal surface, while the molecules of sulfur-containing compounds with smaller volume fill in vacancies. A dense adsorption film would be formed when 4-PQ and sulfur-containing compounds are added at a proper mole ratio.

In some sour reservoirs and tertiary oil recovery blocks, SO₄^2- in solution can cause the corrosion and corrosion fatigue of the sucker rods. In this paper, the corrosion behaviors of super-strength sucker rod FG20 (16Mn2SiCrMoVTiA) steel in the well fluid are investigated by electrochemical measurements, and electron probe micro-analyzer (EPMA) analysis. The results show that FG20 steel has a favorable corrosion resistance in neural solutions. When the hydrogen ion content increases, the hydrolysis of SO₄^2- greatly accelerates the corrosion of FG20 steel. The energy dispersive X-ray(EDX)results demonstrate that the corrosion process of FG20 steel in neural well liquid is an oxygen concentration process, and the protective FeCO₃ and Fe₂O₃ on the surface of the samples can prevent further corrosion. With the increase of the acidity in the well liquid, the corrosion process converts into a sulphide concentration process, and the sloppy FeS and mackinawite film cannot provide effective protection for the specimens, resulting in the increase of corrosion rate.

We use a regional scale photochemical transport model to investigate the surface concentrations and column integrated amounts of ozone (O3) and nitrogen dioxide (NO2) during a pollution event that occurred in the St. Louis metropolitan region in 2012. These trace gases will be two of the primary constituents that will be measured by TEMPO (Tropospheric Emissions: Monitoring of Pollution), an instrument on a geostationary platform, which will result in a dataset that has hourly temporal resolution during the daytime and ~4 km spatial resolution. Although air quality managers are most concerned with surface concentrations, satellite measurements provide a quantity that reflects a column amount, which may or may not be directly relatable to what is measured at the surface. Our model results provide reasonably good agreement with observed surface O3 concentrations (correlation coefficients ranging from 0.69 to 0.87 at each of the nine monitoring stations in the St. Louis region), which is the only trace gas dataset that can be used for verification. The model shows that a plume of O3 extends downwind from St. Louis and contains an integrated amount of ozone of ~ 16 Dobson Units (DU; 1 DU = 2.69 x 1016 molecules cm-2), an amount lower than what was observed during two massive pollution episodes in the 1980s. Based on the smaller isolatable emissions coming from St. Louis, this quantity is not unreasonable, but may also reflect the reduction of photochemical ozone production due to the implementation of emission controls that have gone into effect since the 1980s.

Mycoplasma synoviae (MS) is a highly contagious bacteria that can cause significant harm in commercial poultry populations while not prevented. Rapid detection of its presence in a flock is crucial from the perspective of animals' health and economic income. Authors propose spectral measurements strongly backed up by the AI data processing algorithms for classifying egg origin: from healthy hens or MS-infected ones. The newest obtained classification factors are F-scores for white eggshells 99% and for brown eggshells 99%—all data used for classification were taken by the portable multispectral fibre-optics reflectometer.

The manuscript presents the optical properties of directly deposited films of gold nanoparticles (AuNPs) prepared by ultrasonic spray pyrolysis technology. Four samples were produced, with an AuNPs deposition time of 15 min, 30 min, 1h and 4h on the glass substrate. The morphological characterization of the deposited films showed that the size of the first deposited AuNPs is between 10 and 20 nm, while with a longer duration of the deposition process, larger clusters of AuNPs grow by coalescence and aggregation. The prepared layers were optically characterised with Ultraviolet–visible spectroscopy (UV-vis) and ellipsometry. The ellipsometric measurements showed an increasingly denser and thicker effective thickness of the AuNPs layers. The extinction spectra display a clear local surface plasmonic resonance (LSPR) signature (peak 520-540 nm), indicating the presence of isolated particles in all samples. For all AuNPs layers, the imaginary part of both ε// and ε⏊ is dominated by a central peak around 2.2 eV corresponding to the LSPR of isolated particles and a high-energy shoulder due to Au interband transitions. It is shown that, as the density of particles increases, the extinction cross section grows over the whole spectral range where measurements are taken. Thus response can be explained with an enhanced electromagnetic response among AuNPs, that can be connected to the increase of particle density but also by the formation of clusters and irregular structures.

Background: Anthropometric measurements play a crucial role in medico-legal practices. Actually, several scanning technologies are employed in post-mortem investigations for forensic anthropological measurements. This study aims to evaluate the precision, in-ter-rater reliability, and accuracy of a hand-held scanner in measuring various body parts. Methods: Three independent raters measured seven longitudinal distances using an iPad Pro equipped with a LiDAR sensor and specific software. These measurements were sta-tistically compared to manual measurements conducted by an operator using a laser level and a meterstick (considered the gold standard). Results: The Friedman’s test revealed minimal intra-rater variability in digital measurements. Inter-rater variability analysis yielded an ICC=1, signifying high agreement among the three independent raters. Addi-tionally, the accuracy of digital measurements displayed errors below 2%. Conclusions: Preliminary findings demonstrate that the pairing of LiDAR technology with the Polycam app showcases high precision, inter-rater agreement, and accuracy. Hand-held scanners show potential in forensic anthropology due to their simplicity, affordability, and porta-bility. However, further validation studies under real-world conditions are essential to es-tablish the reliability and effectiveness of handheld scanners in medico-legal settings.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

Capacitance measurements have been extensively used to measure the anchoring extrapolation length L at a nematic-substrate interface. These measurements are extremely delicate because the value found for L often critically depends on the sample thickness and the voltage range chosen to perform the measurements. Several reasons have been proposed to explain this observation, such as the presence of inhomogeneities in the director distribution on the bounding plates or the variation with the electric field of the dielectric constants. In this paper I propose a new method to measure Lp that takes into account this second effect. This method is more general than that proposed in Murauski et al. Phys. Rev. E 71, 061707 (2005) because it does not assume that the anchoring angle is small and that the anchoring energy is of the Rapini-Papoular form. This method is applied to a cell of 8CB treated for planar unidirectional anchoring by photoalignment with the azobenzene dye Brilliant Yellow. The role of flexoelectric effects and the shape of the anchoring potential are discussed.

Optical sensor data can be used to determine changes in anthocyanins, chlorophyll and soluble solids content (SSC) in apple production. In this study, visible and near-infrared spectra (729 to 975 nm) were transformed to SSC values by advanced multivariate calibration models i.e. partial least square regression (PLSR) in order to test the substitution of destructive chemical analyses through non-destructive optical measurements. Spectral field scans were carried out from 2016 to 2018 on marked ’Braeburn’ apples in Southwest Germany. The study combines an in-depth statistical analyses of longitudinal SSC values with horticultural knowledge to set guidelines for further applied use of SSC predictions in the orchard to gain insights into apple carbohydrate physiology. The PLSR models were investigated with respect to sample size, seasonal variation, laboratory errors and the explanatory power of PLSR models when applied to independent samples. As a result of Monte Carlo simulations, PLSR modelled SSC only depended to a minor extent on the absolute number and accuracy of the wet chemistry laboratory calibration measurements. The comparison between non-destructive SSC determinations in the orchard with standard destructive lab testing at harvest on an independent sample showed mean differences of 0.5 % SSC over all study years. SSC modelling with longitudinal linear mixed-effect (LME) models linked high crop loads to lower SSC values at harvest and higher SSC values for fruit from the top part of a tree.

Scanning magnetic microscopy is a new tool that has recently been used to map magnetic fields with good spatial resolution and field sensitivity. This technology has great advantages over other instruments; for example, its operation does not require cryogenic technology, which reduces its operational cost and complexity. Here, we describe the construction of a customizing scanning magnetic microscope based on commercial Hall-effect sensors at room temperature that achieves a spatial resolution of 200 µm. Two scanning stages on the x- and y-axes of precision, consisting of two coupled actuators, control the position of the sample, and this microscope can operate inside or outside a magnetic shield. We obtained magnetic field sensitivities better than 521 nT_rms/√Hz between 1 and 10 Hz, which correspond to a magnetic momentum sensitivity of 9.20 × 10^–10 Am². In order to demonstrate the capability of the microscopy, polished thin sections of geological samples, samples containing microparticles and magnetic nanoparticles were measured. For the geological samples, a theoretical model was adapted from the magnetic maps obtained by the equipment. Vector field maps are valuable tools for the magnetic interpretation of samples with a high spatial variability of magnetization. These maps can provide comprehensive information regarding the spatial distribution of magnetic carriers. In addition, this model may be useful for characterizing isolated areas over samples or investigating the spatial magnetization distribution of bulk samples at the micro and millimeter scales. As an auxiliary technique, a magnetic sweep map was created using Raman spectroscopy; this map allowed the verification of different minerals in the samples. This equipment can be useful for many applications that require samples that need to be mapped without a magnetic field at room temperature, including rock magnetism, the nondestructive testing of steel materials and the testing of biological samples. The equipment can not only be used in cutting-edge research but also serve as a teaching tool to introduce undergraduate, master's and Ph.D. students to the measurement methods and processing techniques used in scanning magnetic microscopy.

This paper explores an event-based version of quantum mechanics which differs from the commonly accepted one, even though the usual elements of quantum formalism, e.g., the Hilbert space, are maintained. This version introduces as primary element the occurrence of micro-events induced by usual physical (mechanical, electromagnetic and so on) interactions. These micro-events correspond to state reductions and are identified with quantum jumps, already introduced by Bohr in his atomic model and experimentally well established today. Macroscopic bodies are defined as clusters of jumps; the emergence of classicality thus becomes understandable and time honoured paradoxes can be solved. In particular, we discuss the cat paradox in this context. Quantum jumps are described as temporal localizations of physical quantities; if the information associated with these localizations has to be finite, two time scales spontaneously appear: an upper cosmological scale and a lower scale of elementary "particles''. This allows the interpretation of the Bekenstein limit like a particular informational constraint on the manifestation of a micro-event in the cosmos it belongs. The topic appears relevant in relation to recent discussions on possible spatiotemporal constraints on quantum computing.

In this research paper, design and development of pyramidal horn antenna for J-band application is reported. It is particularly designed for 17 dB gain and half beam width about 25 degrees at 6.93 GHz. Horn aperture, horn axial length and distance from the throat of the antenna to aperture are the main design constraints which are calculated and used for the antenna design and simulation. Beam width in E-plane and H-plane horn is calculated and it is 19.18 dB and 22.86 dB respectively. The reported antenna design shows good performance for J-band in radiometry, satellite, and radar applications.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

Direct assessments of executive function (EF) are increasingly used in research and clinical settings, with a central assumption that they assess “universal” underlying skills. Their use is spreading globally, raising questions about the cultural appropriateness of assessments devised in Western, industrialized countries. We reviewed multidisciplinary evidence and theory to identify sets of cultural preferences that may be at odds with the implicit assumptions of EF assessments. These preferences relate to motivation and compliance; cultural expectations for interpersonal engagement; contextualized vs. academic thinking; cultural notions of speed and time; the willingness to be silly, be incorrect, or do the opposite; and subject-matter familiarity. In each case, we discuss how the cultural preference may be incompatible with the assumptions of assessments, and how future research and practice can address the issue. Many of the cultural preferences discussed differ between interdependent and independent cultures and between schooled and unschooled populations. Adapting testing protocols to these cultural preferences in different contexts will be important for expanding our scientific understanding of EF from the narrow slice of the human population that has participated in the research to date.

Static and dynamic analysis of website security risks is generally used for website security meas-urements. The website security measurements method recently proposed includes similarity hash-based website security risk analysis and machine learning-based website security risk anal-ysis. In this study, a method that can be performed through information disclosed on the Internet was proposed to measure the risk of a website. DNS information, IP information, and website history information are required to measure the risk of a website. In addition, global traffic rank-ing, malicious code distribution history, and HTTP access status can be checked in the website history information. In this study, information related to the security risk of websites in a total of 2,000 domains was collected and analyzed in 1,000 normal and malicious domains. Through the experiment results, 11 open information collection items were selected to measure the security risk of the website. This study presented the possibility of using public information collection to measure website security risk.

The cutting of difficult-to-machine materials, including their preconditioning, often requires specialised tools and machinery. An alternative processing technology can be cutting materials with a water jet. From the initial stage, the selection of appropriate technological parameters will influence what further finishing treatments will be applied. Vibrations occurring during this process can negatively affect the quality of the cutting edges and surfaces. Therefore, this study analysed vibrations during water-jet cutting with variable technological parameters (speed vfi and pressure pi). To measure the vibrations, a three-axis accelerometer from SEQUOIA was used in water-jet cutting of three materials: aluminum alloy, titanium alloy, and steel. Based on the study, it was found that the maximum value of vibration amplitude reaches the lowest value of vibration acceleration for aluminum alloy (not exceeding 5 m/s2), regardless of the value of pressure during the cutting process. This, taking into account the material properties, indicates that aluminum alloy is the material most susceptible to the cutting process while maintaining a high quality of the cutting surface. Significantly higher values of vibration acceleration amplitude (reaching up to 60 m/s2) during cutting were registered for steel and titanium alloy in all zones and phases of the process (entry zone, cutting zone, and exit zones).

The coast of Oman is observing huge coastal developments to materialize Oman Vision 2040 covering all the strategic sectors. Historical data of coastal hydrodynamic parameters is scarce, even though its importance for a proper design of coastal structures is recognized. Acoustic Doppler Current Profilers were deployed at eleven locations along the coast of Oman. These locations were selected based on their strategic importance for the country. The duration of deployment was from 60 to 265 days. The measured data of waves and current were collected and analyzed using the equipment-specific software and Excel. The significant wave heights can reach 2m along the whole coast of Oman. The southern coast is dominated by the swells. The maximum to significant wave height ratio is approximately 1.5 which is less than a value of 2 obtained using Rayleigh distribution. The coastal currents are stronger along the southern coast than those along the northern coast. The range of current magnitude is from 0.02 m/s to 0.8 m/s. This baseline study will help the public authorities in establishing permanent hydrodynamic measurement stations along the coast of Oman. Moreover, these measurements will serve the practicing engineers in designing coastal structures along the coast of Oman.

Background. To prospectively evaluate the reliability of a portable optical scanner compared to the water displacement technique for volumetric measurements of the foot and ankle, and to compare the acquisition time associated with these two methods. Methods. Foot volume was measured in 29 healthy volunteers (58 feet, 24 female/5 male) by a 3D scanner (UPOD-S 3D Laser Full-Foot Scanner ®) and by water-displacement volumetry. Measurements were performed on both feet, up to a height of 10 cm above the ground. The acquisition time for each method was evaluated. Kolmogorov-Smirnov test, Lin's Concordance Correlation Coefficient, and a Student’s t-test were performed. Results: Mean foot volume was 869.7+/-165.1cm3 (3D scanner) versus 867.9+/-155.4cm3 (water-displacement volumetry) (p <10-5). Concordance of measurements was 0.93, indicative of a high correlation between the two techniques. Volumes were 47.8 cm3 lower when using the 3D scanner versus water volumetry. After statistically correcting this underestimation, the concordance was improved (0.98, residual bias = -0.03 +/- 35.1 cm3). Mean examination time was 4.2 +/-1.7 min (3D optical scanner) versus 11.1 +/-2.9 min (water volumeter) (p<10-4). Conclusion: Ankle/foot volumetric measurements performed using this portable 3D scanner are reliable and fast, and can be used in clinical practice and research.

The on-state voltage of MOSFETs is a convenient and powerful temperature-sensitive electric parameter (TSEP) to determine the junction temperature, thus enabling device monitoring, protection, diagnostics and prognostics. The main hurdle in the use of the on-state voltage as a TSEP is the per-device characterization procedure, to be carried out in a controlled environment, with high costs. In this paper we compare two novel techniques for MOSFET junction temperature estimation: controlled shoot-through and direct heating by resistive heaters embedded in two Kapton (polyimide) films. Both allow in-place characterization of the TSEP curve with the device mounted in its final circuit and assembly, including the working heat sink. The two methods are also validated against the conventional procedure in a thermal chamber.

Regarding number of vehicles, forest roads are characterized by low traffic intensity, but on the other hand great values of ground pressure between wheels of timber truck units and forest road surface occur, often with pressures values above 80 kN which additionally causes damage of the upper and lower forest road layer. There are currently several methods for assessing condition of a forest road surface which are mainly used for assessing state of public roads, but can be used in forestry as well. Assessing condition of forest road surface was done by measuring vibrations with a specially developed software for Android OS installed on a Huawei MediaPad 7 Lite. Software measured vibrations in all three axes, coordinates of device, speed of the vehicle and time. Aim of this research was to determine accuracy of collected data so that this method can be used for scientific and practical purposes. Research was carried out on the segment of a forest road during driving a vehicle equipped with a measuring device. Tests were performed in both driving direction of the forest road segment with different measuring frequencies, tyre inflation pressures and driving speeds. Values of vibrations were classified and translated on a map of forest road together with devices’ measured coordinates. Vibration values were compared with places of recorded forest road surface damages. Research results show no significant difference in vibration values between 1 Hz and 10 Hz of measurement frequencies. Based on the analysis of collected data and obtained results, it is clear that it is possible to assess the condition of a forest road surface by measuring vibrations. The greatest values of vibrations were recorded on the most damaged parts of the forest road. Vibrations do not depend on tyre inflation pressure, but ranges of vibrations are decreasing with decreasing driving speed. Accuracy of collected data depends on GPS signal quality, so it is recommended that each segment of forest road is recorded twice so that location of damages on forest road can be confirmed with certainty.

Environmental deterioration factors are constantly increasing, causing unwanted aesthetic changes to stone artworks due to exposure to various physical and chemical deterioration factors. Inorganic nanoparticle-filled polymer composites have extended their multiple functionalities to various applications, including cultural heritage conservation. Therefore, this study has examined the effects of clay, SiO2, Ca(OH)2 and CaCO3 nanomaterials in the enhancement of the physicomechanical properties of limestone monuments, the aim of the present work being to evaluate comparatively the effectiveness of nanoparticles as consolidation and protection material for limestone artworks. The nanoparticles were added to an acrylic-based copolymer (polyethylmethacrylate (EMA)/methylacrylate (MA) (70/30), in order to improve its physiochemical and mechanical properties, and produced a significant improvement in the ability of the polymers to consolidate and protect the stone. The synthesis process of nanoparticles/polymer nanocomposite has been prepared by an in situ emulsion polymerization system. The nanocomposites contained poly (EMA/MA) with a solid content of 3% [poly (EMA/MA)] in the absence and presence of 5% nanoparticles (0.15 g nanoparticles). Samples were subjected to artificial aging by relative humidity/temperature and acid/salt crystallization weathering to show the optimum conditions of durability and the effectiveness of the nano-mixture in improving the physical and mechanical properties of the stone material. To ensure that the treatment had no negative effects on the physical characteristics of the limestone, the properties of the treated limestone samples were evaluated comparatively before and after artificial aging by the conduct of microstructural (phase morphology studied by means of scanning electron microscopy) and aesthetic (colour and lightness measured by spectrophotometry) analyses. Also used were measurement of static contact angle of water droplets on the surface of the samples, total immersion water absorption, compressive strength, and abrasion resistance test. Results demonstrated that the addition of nanoparticles to an acrylic-based polymer enhanced its capability to consolidate and protect the limestone samples.

A scientific consensus is emerging on the benefits of dc distribution in medium voltage power systems of ships and cities. At least 50% space savings and increased power transfer capacity are estimated with enhanced voltage dc operation of electric cables. The goal of this research is to contribute to developing the empirical knowledge on the insulation performance in order to validate the feasibility of such anticipated gains of dc versus ac, and to determine the comparative impact of different operational conditions from a component engineering point of view. The partial discharge (PD) activity in cables is measured under ac and dc conditions as an indicator of insulation performance. Specifically, PDs in defects at the semicon-insulation interface are studied in terms of inception voltage, repetition rate and discharge magnitude. Empirical understanding is drawn for operating voltage and frequency dependence of the discharge behavior in such voids in the range of 10 to 20\,kV and 0 to 0.1\,Hz, respectively. The change in PD activity with void evolution is explored.

In the last decade Electromagnetic Induction (EMI) measurements have been increasingly used for investigating the soil salinization caused by the use of brackish or saline water as irrigation source. EMI measurements proved to be a powerful tool for providing spatial information of the investigated soil because of the strict correlation between the output geophysical parameter, i.e. the electrical conductivity, to soil moisture and salinity. In addition, their non-invasive nature and their capability to collect a high number of data over broad areas and in relatively short time, makes these measurements attractive for monitoring flow and transport dynamics, otherwise undetectable with conventional measurements. In an experimental field, EMI measurements were collected during the growth season of the tomato, irrigated with three different irrigation strategies. The data were collected over three months in a time-lapse mode in order to visualize changes in electrical conductivity to be associated with soil salinity. A rigorous time-lapse inversion procedure has been set for modeling the soil salinization induced by brackish irrigation water.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

Sea surface salinity (SSS) is one of the Essential Climate Variables (ECVs) as defined by the Global Climate Observing System (GCOS). Acquiring high-quality SSS datasets with high spatial-temporal resolution is cruicial for research on the hydrological cycle and earth climate. This study assessed the quality of SSS data provided by four high-resolution ocean reanalysis products, including the Hybrid Coordinate Ocean Model (HYCOM) 1/12° global reanalysis, the The Copernicus Global 1/12° Oceanic and Sea Ice GLORYS12 Reanal-ysis, the Simple Ocean Data Assimilation (SODA) reanalysis, the ECMWF Oceanic Reanalysis System 5 (ORAS5) product and the Estimating the Circulation and Climate of the Ocean Phase II (ECCO2) reanalysis. Regional comparison in the Mediterranean Sea shows that reanalysis largely depicts the accurate spatial SSS structure away from river mouths and coastal areas but slightly underestimates the mean SSS values. Better SSS reanalysis performance is found in the Levantine Sea while larger SSS uncertainties are found in the Adriatic Sea and the Aegean Sea. The global comparison with CMEMS level-4 (L4) SSS show generally con-sistent large-scale structures. The mean ΔSSS between monthly gridded reanalysis data and in situ analyzed data is -0.1 PSU in the open seas between 40°S and 40°N with the mean Root Mean Square Deviation (RMSD) generally smaller than 0.3 PSU and the majority of correlation coefficients higher than 0.5. Comparison with collocated buoy salinity shows that reanalysis products well captures the SSS variations at the locations of tropical moored buoy arrays at weekly scale. Among all the four products, the data quality of HYCOM re-analysis SSS is highest in marginal sea, GLORYS12 has the best performance in the global ocean especially in tropical regions. Comparatively, ECCO2 has the overall worst performance to reproduce SSS states and variations by showing the largest discrepancies with CMEMS L4 SSS.

Concurrent waves of Coronavirus disease, Ebola virus disease, avian influenza A and black fungus are jeopardizing the lives in some parts of Africa and Asia. From this point of view, this review aims to summarize both socio-economic and public health implications of these parallel outbreaks along with their best possible management approaches. Various online databases were used to collect the necessary information regarding these outbreaks. Based on the reports published and analyses done so far, the long-lasting damages caused by these simultaneous outbreaks on global socio-economical and public health status can be conceived from the past experiences of outbreaks, especially the COVID-19 pandemic. Moreover, prolonged restrictions by the local government may lead to food insecurity, global recession, and an enormous impact on the mental health of people of all ages, specifically in developing countries. Such overwhelming effects already have been reported to be declining national growth of the economy as well as increasing political insecurity and shortage of basic needs. Although various actions have already been taken including vaccination, clinical management, and further research, social distancing, and lockdown, etc. to improve the situation, the emerging variants and associated genetic mutations may make the containment difficult worsening the situation again. Considering the current mutational dynamics of the pathogens and the past experiences, perpetual preparedness along with updated clinical management backed by epidemiological studies and innovating scientific effort are inevitable to combat the simultaneous waves of multiple infectious diseases.

The data from the extended system was recorded on-going basis in the archives of the monitoring system, and the multipoint system was directly stored in the methane-anemometers, which allows one to perform a comparative analysis of the obtained records from many methane detectors. An important element of the analyses was the simultaneous registration of the methane concentration in the longwall, together with information on operating time, direction of shearer operation and type of work: mining/cleaning. Mining practice shows that in methane coal mines, methane is often the basic limitation for modern and high-efficiency longwall complexes. The paper reports on selected observations and tests carried out in the Cw-4 longwall in seam 364/2 of the Budryk mine belonging to JSW SA. In observation of the methane level in the Cw-4 longwall, additional sensors installed in the end part of the longwall from the side of the gobs and registration of air velocity and methane concentration in the multipoint system built in the selected longwall cross-section were used, regardless of the air parameters recorded in the monitoring system.

Beer fermentation is typically monitored by periodic sampling and off-line analysis. In-line sensors would remove the need for time-consuming manual operation and provide real-time evaluation of the fermenting media. This work uses a low-cost ultrasonic sensor combined with machine learning to predict the alcohol concentration during beer fermentation. The highest accuracy model (R2=0.952, MAE=0.265, MSE=0.136) used a transmission-based ultrasonic sensing technique along with the measured temperature. However, the second most accurate model (R2=0.948, MAE=0.283, MSE=0.146) used a reflection-based technique without the temperature. Both the reflection-based technique and the omission of the temperature data are novel to this research and demonstrate the potential for a non-invasive sensor to monitor beer fermentation.

The accurate quantification of $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios for Mössbauer spectroscopic room temperature measurements involves many steps and, when shown in a composite Mössbaur data table, does not allow enough space for more Mössbauer parameters to be presented in the composite table. So a simple formula is derived, (presented as a short communication) which users will find helpful when they have to determine corrected $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios in their room temperature Mössbauer experiments.

This work presents preliminary experimental results advancing non-destructive testing methods for detecting steel bars in concrete structures via contactless investigation in the X-band spectrum. The study reveals the field’s penetration into concrete, extracting insights into embedded bars through scattered data. Applying a quasi-quadratic inverse scattering technique to numerically simulated data yields promising results, confirming the effectiveness and reliability of the proposed approach. In this realm, using a higher frequency allows the use of lighter equipment and smaller antennas. Identified areas for improvement include accounting for antenna behavior and establishing undeformed target morphology and precise orientation. Transitioning from powder-based and sand specimens to real solid reinforced concrete structures is expected to alleviate laboratory challenges. Although accurately determining concrete properties such as relative permittivity and conductivity is essential, it remains beyond the scope of this study. Finally, overcoming these challenges could significantly enhance non-invasive testing, improving structural health monitoring and disaster prevention.

This study employs Principal Component Analysis to examine cranial measurements obtained from both extant and fossil specimens spanning 38 species and comprising over 300 individuals within the subfamily Cervinae. Our findings elucidate craniometric distinctions among cervids characterized by varying body sizes and certain evolutionary adaptations. While our results generally corroborate previous assertions regarding the limited craniometric variability among plesiometacarpal deer, they also unveil specific cranial adaptations within certain genera and species. The Principal Component Analysis of craniometric data revealed that giant and large-sized deer display significantly broader ecomorphological diversity in cranial shape compared to small-sized deer. Secondly, small-sized deer exhibit greater uniformity in their cranial shape, appearing densely clustered on the factorial map. Thus, we conclude that body size imposes ecological constraints, limiting the available niches due to eco-physiological factors. The study demonstrates that endemic insular deer do not evolve consistent craniometric features attributable to insular isolation, while the cranial proportions of medium-to-small sized deer delineate a ubiquitous morphological archetype characteristic of numerous cervid taxa spanning diverse phylogenetic lineages and sharing comparable body sizes. This group of "Dama-like" deer, characterized by similar body size, metabolic rates, ecological needs, and cranial morphometry, is referred to here as the fundamental eco-physiological type, typical of warm regions within the Palearctic and Oriental biogeographic realms..

Hafnium is a metal with rare properties, such as a low superconducting transition temperature slightly above 100 mK, which makes it attractive for a lot of applications, especially for design and fabrication of microcalorimeters with high energy resolution. In this paper we describe the results of fabrication and experimental investigation of superconducting properties of hafnium thin films in a dilution refrigerator. The considered Hf films, whose thickness is in the range from 60 to 115 nm, are deposited on substrates by electron beam evaporation. The combinations with thin layers of normal metals to decrease the critical temperature of superconducting hafnium films by proximity effect, are also considered. The critical temperature of the studied films varies from 56 to 302 mK. Also, significant increase of the critical temperature of some films over time was observed and investigated.

The main problem in pursuing multiple extended targets tracking is distinguishing the origins of the measurements. The association of measurements to the possible origins within the target’s extent is difficult, especially for the occlusions or the detection blind zone which cause the intermittent measurements. To solve the problem, a hierarchical network-based tracklets data association algorithm is proposed. At the low level, the min cost network flow model is used to extract possible tracklets from the divided measurement set. At the high-level, the trajectories are estimated from the tracks produced by the previous low level network. The experimental results show that the hierarchical network-based tracklets data association algorithm outperforms the JPDA and RFS-based method when the measurement is intermittently unavailable.

The paper presents a new conception of quasi-distributed sensor for simultaneous measurement of several physical fields and the results of an experimental study of this sensor. A distinctive feature of the sensor defined by the sensitive RC elements connected in the original tree-like structure. The proposed is the structure of the sensor and measurement system as well as corresponding measurement algorithm. The high accuracy demonstrated by the sensor’s prototype gives possibility to effective use the proposed sensors in many technical and scientific applications.

This joint experimental-theoretical work focuses on molecular and photophysical properties of the spiropyran-containing amphiphilic molecule in organic and aqueous solutions. Being dissolved in tested organic solvents, the system demonstrates positive photochromism, i.e. upon UV stimulus the colorless spiropyran form is transformed into colorful merocyanine isomer. However, aqueous solution of the amphiphile possesses a negative photochromism: the orange-red merocyanine form turns to be thermodynamically more stable in water, and both UV and vis stimuli lead to the partial or complete photobleaching of the solution. The explanation of this phenomenon is given on the basis of density functional theory calculations and classical modeling including thermodynamic integration. The simulations reveal that stabilization of merocyanine in water proceeds with the energy of ca. 70 kJ mol−1, and that the Helmholtz free energy of hydration of merocyanine form is 100 kJ mol−1 lower as compared to the behavior of SP isomer in water. The explanation of such a difference lies in the molecular properties of the merocyanine: after ring-opening reaction this molecule transforms into a zwitterionic form, as evidenced by the electrostatic potential plotted around the opened form. The presence of three charged groups on the periphery of a flat conjugated backbone stimulates the self-assembly of merocyanine molecules in water, ending up with the formation of elongated associates with stack-like building blocks, as shown in molecular dynamics simulations of the aqueous solution with the concentration above critical micelle concentration. Our quantitative evaluation of the hydrophilicity switching in spiropyran/merocyanine containing surfactants may prompt the search for new systems, including colloidal and polymeric ones, aiming at remote tuning of their morphology, which could give new promising shapes and patterns for the needs of modern nanotechnology.

Denture wearers often complain about jeopardized function and reduced quality of life due to lack of prosthesis’ retention. Implant retained mandibular overdentures, on 2 non-connected implants (2IOD) are well-proven solutions to overcome these issues. We prospectively assessed 69 patients and scrutinized clinical records until at least 7 years of function. Thirty-six were retained on Locator ® Abutments (LA) and thirty-tree on Ball Abutments (BA). Both systems were compared regarding the type, amount and total cost of required maintenance. One implants was lost, yielding 98.7% survival after 7 years. In total 438 technical issues occurred: 121 (27.35%) in BA and 317 (72.4%) in LA. Out of these, 343 events (78%) were solved chairside: 191 (43.6%) were replacements of retention caps, 113 (25.8%) were minor acrylic repairs, in 26 (5.9%) pressure ulcers had to be relieved and 13 (3%) related to abutments. LA required 179 insert replacements compared to 12 in the BA group. The overall initial treatment cost was 3850 euro. The average total maintenance cost in relation to the initial cost for the LA and BA groups was 19.11% (range 0% - 82.24%) and 18.91% (range 0% - 113.26%) respectively (P=0.540). Conclusions: The 7-years maintenance costs for a 2IOD is acceptable when the patient is regularly checked and professionally maintained. Most events are easily solvable chairside, but a few patients required more expensive interventions, regardless of the type of attachment used.

The article aims to present the possible use of the simple modified optical training kit as a low-cost, simple setup for high precision surface speed measurements. A measurement capability evaluation of the optical Doppler kit used for velocimetry of a fast-rotating reflecting surface is presented. To get high repeatability measurements, we modified a fibre optic interferometry training kit. By using signal processing and statistics a precision under repeatability conditions of measurements was evaluated. Expressed by the standard deviations (3σ’s) the surface velocity measurements precision below 0.2 m/s is shown. The Cg’s capability indices were also evaluated. We postulate, the electric circuit stability of the measurement system power supply is essential for a signal noise reducing process for a wide range of metrology systems. It is crucial for precision measurements.

The gap in knowledge regarding the radiative effects of aerosols in the UV region of the solar spectrum is large, mainly due to the lack of systematic measurements of the aerosol single scattering albedo (SSA) and absorption optical depth (AAOD). In the present study, spectral UV measurements performed in Thessaloniki, Greece by a double monochromator Brewer spectrophotometer in the period 1998 - 2017 are used for the calculation of the aforementioned optical properties. The main uncertainty factors have been described and there is an effort to quantify the overall uncertainties in SSA and AAOD. Analysis of the results suggests that the absorption by aerosols is much stronger in the UV relative to the visible. SSA follows a clear annual pattern ranging from ~0.7 in winter to ~0.85 in summer at wavelengths 320 – 360 nm, while AAOD peaks in summer and winter. The average AAOD for 2009 – 2011 is ~50% above the 2003 – 2006 average, possibly due to increased emissions of absorbing aerosols related to the economical crisis and the metro-railway construction works in the city center. A detailed analysis of the uncertainties in the retrieval of the SSA and the AAOD from the Brewer spectrophotometer has been also performed.

This study aims at an acoustic design of the classical concert hall and evaluation of the acoustic performance. In terms of three acoustic parameters (i.e., reverberation time (RT), clarity (C80), and lateral fraction (LF)), this study performed acoustic simulation modeling and site measurement with the K Art Hall located in South Korea as a case study. First, in order to meet the acoustic performance of the K Art Hall (target RT: 1.4~1.7 seconds, target C80: -2dB or more +2dB or less, and target LF: 10~35%), the finish materials and shape of the room as an interior acoustic design were determined. Second, the average values of the RT, C80, and LF using the acoustic simulation modeling were estimated at 1.4 second, 1.2~1.6 dB, and 29%, respectively. Third, the average values of the RT, C80, and LF through site measuring were measured at 1.5~1.64 second, 0.07~1.31dB, and 22.22~31.37%, respectively. Thus, the results of both the acoustic simulation modeling and site measuring were analyzed so as to satisfy the target acoustic performance. The results of this study will help the decision-makers (i.e., owner, construction managers, etc.) to plan the classical concert hall in terms of the RT, C80, and LF.

In factory automation systems, hybrid wired/wireless networks are often deployed to connect devices of difficult reachability such as those mounted on mobile equipment. A widespread version of these networks makes use of Access Points (APs) to implement wireless extensions of Real--Time Ethernet (RTE) networks via the IEEE 802.11 Wireless LAN (WLAN). Unfortunately, APs may introduce random delays in packet forwarding, mainly related to the their internal behaviors (e.g. code processing times) that negatively impact on the whole performance of the automation systems. Consequently, the knowledge of these delays represent a crucial design information. This paper presents an original and effective method to measure the delays introduced by APs, exploiting a hybrid loop-back link and a simple set-up with moderate instrumentation requirements. The method, which requires an initial calibration by means of a reference AP, has been successfully tested on some commercial APs. As it will be shown, the proposed measurement procedure is general and, as such, can be profitably adopted in even different scenarios.

Optical microcombs represent a new paradigm for generating laser frequency combs based on compact chip-scale devices, which have underpinned many modern technological advances for both fundamental science and industrial applications. Along with the surge in activity related to optical micro-combs in the past decade, their applications have also experienced rapid progress ‒ not only in traditional fields such as frequency synthesis, signal processing, and optical communications, but also in new interdisciplinary fields spanning the frontiers of light detection and ranging (LiDAR), astronomical detection, neuromorphic computing, and quantum optics. This paper reviews the applications of optical microcombs. First, an overview of the devices and methods for generating optical microcombs is provided, which are categorized into material platforms, device architectures, soliton classes, and driving mechanisms. Second, the broad applications of optical microcombs are systematically reviewed, which are categorized into microwave photonics, optical communications, precision measurements, neuromorphic computing, and quantum optics. Finally, the current challenges and future perspectives are discussed.

Inverse problems of recovering surface fluxes on the boundary of a domain from pointwise observations are considered. Sharp conditions on the data ensuring existence and uniqueness of solutions in Sobolev classes are exposed. They are smoothness conditions on the data, geometric conditions on the location of measurement points, and the boundary of a domain. The proof relies on asymptotics of fundamental solutions to the corresponding elliptic problems and the Laplace transform. The problem is reduced to a linear algebraic system with a nondegerate matrix.

Wearable cardiac sensors pave the way to advanced cardiac monitoring applications based on heart rate variability (HRV). In real-life settings, heart rate (HR) measurements are subject to mo-tion artifacts that can be timely removed from the recordings. This leads to frequent data loss in the HR signal, especially for commercial devices based on photoplethysmography (PPG). The cur-rent study had two main goals: (i) to provide a white-box quality index that estimates the amount of missing samples in any piece of HR signal; and (ii) to quantify the impact of data loss on feature extraction in a PPG-based HR signal. This was done by comparing real-life recordings from com-mercial sensors featuring both PPG (Empatica E4) and ECG (Zephyr BioHarness 3). After an out-lier rejection process, our quality index was used to isolate portions of ECG-based HR signal that could be used as benchmark, to validate the output of Empatica E4 at the signal level and at the feature level. Our results showed high accuracy for estimating the mean HR, poor accuracy for short-term HRV features and moderate accuracy for longer-term HRV features. Levels of error could be substantially reduced by using our quality index to identify time windows with few or no missing data.

Starting with unitary quantum dynamics, we investigate how to add quantum measurements. Quantum measurements have four essential components: the furcation, the witness production, an alignment projection, and the actual choice decision. The first two components still lie in the domain of unitary quantum dynamics. The decoherence concept explains the third contribution. It can be based on the requirement that witnesses reaching the end of time on the wave function side and the conjugate one have to be identical. In this way, it also stays within the quantum dynamics domain. The surjection hypothesis explains the actual choice decision. It is based on a two boundary interpretation applied to the complete quantum universe. It offers a simple way to reduce these seemingly random projections to purely deterministic unitary quantum dynamics, eliminating the measurement problem.

Spatiotemporal dynamics of the atmospheric kinetic energy and its components caused by the ordered and turbulent motions of air masses are estimated from minisodar measurements of three velocity vector components and their variances within the lowest 5–200 m layer of the atmosphere, with a particular emphasis on the turbulent kinetic energy. The layered structure of the total atmospheric kinetic energy has been established. From the diurnal hourly dynamics of the altitude profiles of the turbulent kinetic energy (TKE) retrieved from minisodar data, four layers are established by the character of the altitude TKE dependence, namely, the near-ground layer, the surface layer, the layer with a linear TKE increase, and the transitive layer above. In the first layer, the most significant changes of the ТКЕ were observed in the evening hours. In the second layer, no significant changes in the TKE values were observed. A linear increase in the TKE values with altitude was observed in the third layer. In the fourth layer, the TKE slightly increased with altitude and exhibited variations during the entire observation period. The altitudes of the upper boundaries of these layers depended on the time of day. The MKE values were much less than the corresponding TKE values, they did not exceed 50 m²/s². From two to four MKE layers were distinguished based on the character of its altitude dependence. The two-layer structures were observed in the evening and at night (under conditions of the stable atmospheric boundary layer). In the morning and daytime, the four-layer MKE structures with intermediate layers of linear increase and subsequent decrease in the MKE values were observed. Our estimates demonstrated that the ТКЕ contribution to the total atmospheric kinetic energy considerably (by a factor of 2.5–3) exceeded the corresponding МКЕ contribution.

Electrification of society, increasing renewable energy sources and mobility charging lead to new loading patterns for power transformers. Dynamic load conditions induce enhanced mechanical stress on the transformers’ windings, potentially causing degradation of the solid insulation over time and compromising the transformer's short-circuit withstand capability. Thermal expansion of the windings, caused by losses in the copper conductors, occurring as the transformer is load-ed, increases the stress. Conversely, magnetic losses in the core and tie plate expansion contribute to a reduction in stress. This paper presents the effect of step changes in core losses and copper losses by on-line measurements of the clamping pressure, to better understand the mechanical stresses acting upon the solid insulation cellulose materials.

Goal of this article is to provide the numerical and experimental assessments of an effective near-field to far-field transformation (NF–FF T) technique with planar spiral scanning for flat antennas under test (AUTs), which requires a non-redundant, i.e. minimum, amount of NF measurements. This technique has its roots in the theory of non-redundant sampling representations of electromagnetic fields and has been devised by suitably applying the unified theory of spiral scans for non-volumetric antennas to the case in which the considered AUT is modeled by a circular disk having its radius equal to one half the AUT maximum dimension. It makes use of a 2-D optimal sampling interpolation (OSI) formula to accurately determine the massive NF data required by the classical plane-rectangular NF–FF T technique from the non-redundant ones gathered along the spiral. It must be emphasized that, when considering flat AUTs, the developed transformation allows to further and significantly save measurement time as compared to that needed by the previously developed NF–FF T techniques with planar spiral scans based on the quasi-planar antennas modelings, because the number of turns of the spiral and that of NF data to be acquired depend somehow on the area of the modeling surface. The reported numerical simulations assess the accuracy of the proposed NF–FF T technique, whereas the experimental tests prove its practical feasibility.

In the broad field of Inverse Analysis and Structural Identification, it is nowadays of a large interest the study of Gaussian Processes, as a reliable and efficient optimisation method, particularly helpful toward the identification of a global optimum point, under the conditions of complicated functions to be optimised. In the present contribution, a specific case study is considered, focusing on a historical road reinforced concrete arched bridge, located in Northern Italy, employing dynamic modal properties, deciphered from in-situ measurements, previously acquired under operational traffic conditions, by a standard wired accelerometer system, placed at the deck level. Aiming at the identification and diagnosis of the bridge structure, three main methodological steps are herein considered: the adoption of a FEM model of the structure (in the linear dynamic framework), the definition of an appropriate discrepancy function, based on measured and numerically computed quantities (natural frequencies and mode shapes of the bridge), and the investigation of such a discrepancy function, toward a consistent selection of an optimisation strategy for the identification of sought parameters (Young’s moduli and mass densities of diverse elements of the structure). The presented developments, within the framework of methodological optimisation approach by Gaussian Processes, and achieved results display a rather efficient perspective, with reference to the considered case study, toward inverse analysis for structural diagnosis, in the context of strategic (historical) infrastructures.

In the context of Inverse Analysis in Civil Engineering, parameter identification and model calibration, of a structural system, relying on dynamic measurements, are subjects of a growing research interest. In the present contribution, the topic is tackled with reference both to simplified structural numerical examples and to a specific case study, namely a historical road three-span reinforced concrete arched bridge, with vibrational data previously acquired by standard wired accelerometers on the deck, under operational traffic conditions. In particular, the present work aims at focussing on the identification issues, concerning the definition of a maximum allowable threshold number of sought material parameters (e.g., Young’s moduli and mass densities of different structural components), with respect to the amount of available measurement data, and the investigation of the inverse analysis discrepancy function to be optimised, in order to set the intrinsic issue of multiple “realizations”, in case of a plain use of modal properties, and in view of forming a well–posed optimisation problem. Structural modelling, sensitivity analysis and numerical optimisation approaches are herein combined toward a robust and efficient identification strategy, to be effectively employed in structural assessment and diagnosis, also with respect to originally available or enriched sets of experimental data. The proposed methodology, and collected results, shall outline an efficient identification procedure, in view of automated inverse analysis, practically oriented to the dynamic assessment and structural diagnosis in the Civil Engineering context, as applied e.g. to strategic bridge infrastructures.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Eddy current based approaches have been investigated for a wide range of inspection applications. Dodd-Deeds model and the truncated region eigenfunction expansion (TREE) method are widely applied in various occasions, mostly for the cases that the sample is relatively larger than the radius of the sensor coil. The TREE method converts the integral expressions to the summation of many terms in the truncated region. In a recent work, the impedance of the co-axial air-cored sensor due to a plate of finite radius was calculated by the modified Dodd-Deeds analytical approach proposed by authors. In this paper, combining the modified analytical solution and the TREE method, a new finite region eigenfunction expansion (FREE) method is proposed. This method involves modifying its initial summation point from the first zero of the Bessel function to a value related to the radius of the plate, therefore makes it suitable for plate with finite dimensions. Experiments and simulations have been carried out and compared for the verification of the proposed method. Further, the planar size measurements of the metallic circular plate can be achieved by utilising the measured peak frequency feature.

The grain size of CVD (Chemical Vapor Deposition) graphene was controlled by changing the precursor gas flow rates, operation temperature, and chamber pressure. Graphene of average grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm were synthesized in high quality and full coverage. The possibility to tailor the thermoelectric conversion characteristics of graphene has been exhibited by examining the grain size effect on the three elementary thermal and electrical properties of σ, S, and k. Electrical conductivity (σ) and Seebeck coefficients (S) were measured in a vacuum for supported graphene on SiO₂/Si FET (Field Effect Transistor) substrates so that the charge carrier density could be changed by applying a gate voltage (V_G). Mobility (µ) values of 529~1042, 459~745, and 314~490 cm²/V·s for the three grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm, respectively, were obtained from the slopes of the measured σ vs. V_G graphs. The power factor (PF), the electrical portion of the thermoelectric figure of merit (ZT), decreased by about one half as the grain size was decreased, while the thermal conductivity (k) decreased by one quarter for the same grain decrease. Finally, the resulting ZT increased more than two times when the grain size was reduced from 4.1 µm to 0.5 µm.

Non-exhaust road transport emissions in cities contribute to poor air quality and create health impacts. This paper presents a new study of the emitted particles due to the tyres-road wear ‘TRWP’ in real driving and gives their emission factors EF. The most frequently observed particles were &lt;1 µm; followed by particles size between [1µm, 4µm] for urban, suburban and highway areas. These particle sizes are well-known to have a higher degree of toxicity. An overall analysis of all the measured pollutants gave EF equal to 30 10+12 #/km and 35 10+12 #/km, respectively for urban and sub-urban areas; and 5 10+12 #/km on highway. The analysis of the 19 most emitted pollutants, taken individually, showed that their EFs ranged from 0.003 to 18.142 10+12#/km. The obtained EF are above the value of the Euro standard for vehicles, but are below the values for vehicles unequipped with a particle filter. Significant test analysis confirmed that inertia of chemical pollutants is homogeneous. EF assessment of the PM10 and PM2.5 emitted is equal to 1.45 mg/km and 0.35 mg/km respectively. These results should contribute to the emergence of future regulations of non-exhaust emissions and should help to analyse the exposure-impact relationship to TRWP.

Sanctuaries devoted to Asclepius were established and operated for almost a thousand years in various Greek and Roman cities throughout the Mediterranean region. The Asclepieion sanctuary in Lenta (formerly known as Ancient Lebena) in Crete was famous for receiving water from a sacred spring. In the Ancient Lebena, Levinaion was a famous centre for hydrotherapy, physiotherapy and a psychiatric hospital. In the present paper, we aim to assess the hydrochemical status of this sacred spring that holds a prominent position in archaeological and historical studies. The main objectives of this study are: Initially, to present supervisory evidence (archaeological, geological, hydrochemical) of an area that was a water resource management model for many centuries, carrying out therapeutic work. The second objective is to present and compare hydrochemical data in the last century, i.e. from 1915 to 2021. The third objective is to highlight and warn of an incipient saltwater intrusion in the area along the Lentas coast. The fourth objective is to propose an alternative and sustainable form of water resources management in the region that requires the study and rational utilization of the sporadic small water springs in the region. Our study focuses on a basic hydrochemical analysis of spring and borehole water in the remains of Levinaion in the Lentas region and their comparison with spare historical data of the sacred spring water, aiming to interpret the impact of the changes in the spring water resources that occurred in the last decades due to urban modernization. Our results highlight (i) visible fluctuations in chemical composition of borehole water samples, (ii) a neutral to alkaline pH in borehole waters, and an alkaline pH in spring waters, (iii) un-detectable arsenic of Lentas borehole water, unlike historical data of Lentas spring water, (iv) low values of dissolved radon of Lentas borehole water and spring water of Kefalovrysa, and (v) a timeless constant and hypothermic nature of the water of both sacred spring and borehole of Lenta, but also of Kefalovrysa spring. The recorded historical data, i.e. from 1915 to 1957, due to the absence of substantial anthropogenic activity in the area, can be used as reference values (natural background levels, NBLs) for the Lentas area. Our findings emerge with the need to bring again the flowing spring water of the sacred spring of Lentas in its original form through sustainable management and re-discover its beneficial therapeutical effects.

Currently Single Board Computers (SBCs) are sufficiently powerful to run Real-Time Operating Systems (RTOSs) and applications with real-time attributes and requirements. SBCs serve as a foundation in Industrial Internet of Things (IIoT). The NXP Semiconductors produces a series of SBCs based on ARM-processors for a variety of industrial applications. The continuous increase in real-time data generated by IoT devices adds further research issues about the efficiency of such systems and applications. The purpose of this research was to investigate the timing performance of an NXP TWR-K70F120M device with μClinux OS on running concurrently tasks with real-time features and constraints. A custom-built multithreaded application with specific compute-intensive sorting and matrix operations was developed and applied to obtain measurements in specific timing metrics, including task’s execution time, threads waiting time, and response time, under different threads variations. The performance of this device was additionally benchmarked and validated against favorite platforms, a Raspberry Pi4 and BeagleBone AI SBCs. The experimental results showed that this device stands well both in terms of timing and efficiency metrics. Execution times were quite lower than the others, by approximately 56% in the case of two threads, and by 29% in the case of thirty-two threads configurations.

In the context of video background-foreground separation, we propose a compressive online Robust Principal Component Analysis (RPCA) with optical flow that separates recursively a sequence of video frames into foreground (sparse) and background (low-rank) components. This separation method can process per video frame from a small set of measurements, in contrast to conventional batch-based RPCA, which processes the full data. The proposed method also leverages multiple prior information by incorporating previously separated background and foreground frames in an n-l₁ minimization problem. Moreover, optical flow is utilized to estimate motions between the previous foreground frames and then compensate the motions to achieve higher quality prior foregrounds for improving the separation. Our method is tested on several video sequences in different scenarios for online background-foreground separation given compressive measurements. The visual and quantitative results show that the proposed method outperforms other existing methods.

This study reports the synthesis and characterization of novel per-fluorinated organic polymers with azo- and azomethine-based linkers using nucleophilic aromatic substitution. The polymers reveal variations in the fluorine content via the incorporation of decafluorobiphenyl and hexafluorobenzene linkers, which enhanced their hydrophobic nature. The rich fluorine polymers were slightly soluble in THF and have shown molecular weights between 4886 to 11948 g/mol. All polymers exhibit thermal stability in the range of 350-500°C, with varying thermal stability depending on the fluorine and nitrogen content. Conjugation of the polymers was confirmed through changes in the UV-Vis spectra, with a hypsochromic shift observed in all cases, more pronounced in azo-based fluorinated chains due to H-bonding on the nitrogen sites, chain conformations, and planarity. The optical band gap (Eg) of the polymers was determined from the UV-Vis data, with the Eg values of the azo-based fluorinated polymers being 1 eV higher than those of their corresponding linkers. The cross-linking formation was characterized by porosity measurements, with the azo-based polymer exhibiting the highest surface area of 770 m²/g with a pore volume of 0.35 cm³/g, while the open-chain azomethine-based polymer exhibited the lowest surface area of 285 m²/g with a pore volume of 0.0872 cm³/g. Porous structures with varied hydrophobicities were investigated as adsorbents for separating water-benzene and water-phenol mixtures and selectively binding methane/carbon dioxide gases from the air. The most hydrophobic polymers containing the decafluorbiphenyl linker were suitable for benzene separation, while the best methane uptake values were 6.14 and 3.46 mg/g for DAB-Z-1O and DAB-A-1O, respectively. DAB-Z-1h, with the highest surface area and rich in nitrogen sites, exhibited the highest CO₂ uptake at 298 K (17.25).

In this study, multi-layer ceramic capacitors (MLCCs) detached from lighting sector's waste electrical-electronic equipment (WEEE) are characterised for the presence of rare earth elements (REEs) and precious metals (PMs). Their digestion was carried out with HNO3 & aqua regia on a heating plate and characterised with the use of inductively coupled plasma optical emission spectroscopy (ICP-OES) & scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The contents of REEs and PMs are 0.84 wt% and 0.60 wt%, respectively, and create an economic stored value in MLCCs that is essentially defined by PMs of 98.67% and by Pd 78.37%. The content of the main elements is: Nd 0.366 wt%, Y 0.220 wt%, Dy 0.131 wt%, Ag 0.467 wt%, and Pd 0.105 wt%. The results confirm the need of selective removal and separate recycling process of MLCCs from WEEE drivers.

The utilization of Fiber Bragg Grating (FBG) sensors in innovative optical sensor networks has displayed remarkable potential in providing precise and dependable thermal measurements in hostile environments on Earth. Multi-Layer Insulation (MLI) blankets serve as critical components of spacecraft and are employed to regulate the temperature of sensitive components by reflecting or absorbing thermal radiation. To enable accurate and continuous monitoring of temperature along the length of the insulative barrier without compromising its flexibility and lightweight, FBG sensors can be embedded within the thermal blanket, thereby enabling distributed temperature sensing. This capability can aid in optimizing the thermal regulation of the spacecraft and ensuring the reliable and safe operation of vital components. Furthermore, FBG sensors offer several advantages over traditional temperature sensors, including high sensitivity, immunity to electromagnetic interference, and the ability to operate in harsh environments. These properties make FBG sensors an excellent option for thermal blankets in space applications, where precise temperature regulation is crucial for mission success. Nevertheless, the calibration of temperature sensors in vacuum conditions poses a significant challenge due to the lack of an appropriate calibration reference. Therefore, this paper aims to investigate innovative solutions for calibrating temperature sensors in vacuum conditions. The proposed solutions have the potential to enhance the accuracy and reliability of temperature measurements in space applications, which can enable engineers to develop more resilient and dependable spacecraft systems.

The most common source of transformer failure is in the insulation, and the most prevalent warning signal for insulation weakness is partial discharge (PD). Locating positons of these partial discharges would help repair the transformer to prevent failures. This work investigates algorithms that could be deployed to locate the position of a PD event using data from ultra-high frequency (UHF) sensors inside the transformer. These algorithms typically proceed in two steps: first determine the signal arrival time and then locate the position based on time differences. This paper reviews available methods for each task and then propose new algorithms: a convolutional iterative filter with thresholding (CIFT) to determine the signal arrival time and a reference table of travel times to resolve the source location. The effectiveness of these algorithms are tested with a set of laboratory-triggered PD events and two sets of simulated PD events inside transfers in production use. Tests show the new approach provides more accurate locations than the best-known data analysis algorithms, and the difference is particularly large, 3.7X, when the signal sources are far from sensors.

The EPR paradox was caused by the provision that quantum variables must have pre-existing values. This type of “hidden property realism” was later falsified by Bell’s Theorem. Accordingly, the physical basis for action-at-a-distance between entangled quanta was removed. Yet, modern interpretations present Bell’s inequality as a Locality Criterion, as if Bell violations can only happen at the quantum level, and only with remote interactions. This is a questionable practice, considering that classical joint measurements also violate such inequalities for mutually exclusive wave properties. In particular, consecutive measurements of polarization produce the same coef-ficients of correlation as parallel measurements with entangled quanta, yet they are explicitly local. Furthermore, it is possible to combine parallel and consecutive measurements of Type I polariza-tion-entangled photons in a single experiment, conclusively showing that quantum Bell violations can be local. Surprisingly, classical phenomena also require nonlocal interpretations if pre-existing properties are taken for granted. Hence, the solution is to reject the models with pre-existing properties for both classical and quantum wave-like phenomena.

The transmission and analysis of data is one of the challenges of the 21st century. In the field of environmental measurement technology, existing broadband and wireless technologies have not been able to transmit data reliably and cost-effectively over long distances and in hard-to-reach places. LoRaWAN, an IoT technology, could be an energy-efficient, cost-effective and secure alternative as a narrowband technology in combination with battery-powered sensors and thus make an important contribution to the intelligent, largely wireless networking of objects, plants and machines (IoT), for example in the municipal sector. In addition to ecological and economic benefits, the quality of life in modern, intelligently networked cities can be enhanced by real time data acquisition. However, the prerequisite is that the quality of the data acquired via this method is sufficiently good. This paper therefore addresses the question of the quality of particulate matter data collected by low-cost sensors. To determine this, an SDS011 particulate matter sensor from Nova Fitness was ported to LoRaWAN. The sensor was installed next to a governmental measurement station. In a test that lasted five weeks, data from the SDS011 sensor were compared with those from the governmental station. Differences were identified and a correction approach was developed and applied. The efficiency of the approach was verified. Based on the results, it can be seen that the use of the low cost sensors has weaknesses. Problems can only be partially reduced. Nevertheless, the use of the low-cost sensors can be helpful for a flexible and cost effective collection of environmental data.

SLM Additive Manufacturing has demonstrated great potential for aerospace applications when structural elements of individual design and/or complex shape need to be promptly supplied. 3D-printable AlSi10Mg (RS-300) alloy is widely used for the fabrication of different structures in aerospace industry. The importance of the evaluation of residual stresses that arise as a result of complex 3D-printing process thermal history is widely discussed in literature, but systematic assessment remains lacking for their magnitude, spatial distribution, and comparative analysis of different evaluation techniques. In this study we report the results of a systematic study of residual stresses in a 3D-printed double tower shaped samples using several approaches: the contour method, blind hole drilling laser speckle interferometry, X-ray diffraction, and Xe pFIB-DIC micro-ring-core milling analysis. We show that a high level of tensile and compressive residual stresses is inherited from SLM 3D-printing and retained for longer than 6 months. The stresses vary over a significant proportion of the material yield stress. All residual stress evaluation techniques considered returned comparable values of residual stresses even regardless of dramatically different dimensional scales from millimeters for the Contour Method down, laser speckle interferometry and XRD and down to small fractions of a mm (70 μm) for Xe pFIB-DIC ring-core drilling. The use of residual stress evaluation is discussed in the context of optimizing the printing strategy to enhance the mechanical performance and long-term durability.

It is unclear which noise exposure time window and noise characteristics during nighttime are most detrimental for sleep quality in real life settings. We have conducted a field study with 105 volunteers wearing a wrist actimeter to record their sleep during seven days, together with concurrent outdoor noise measurements at their bedroom window. Actimetry recorded sleep latency increased by 5.6 minutes (95% confidence interval: 1.6 to 9.6 minutes) per 10 dB(A) increase in noise exposure during the first hour after bedtime. Actimetry assessed sleep efficiency was significantly reduced by 2-3 percent per 10 dB(A) increase in measured outdoor noise (Leq, 1h) for the last three hours of sleep. For subjectively reported sleepiness, noise exposure during the last hour prior to wake up was most crucial with an increase in the sleepiness score of 0.31 units (95% CI: 0.08 to 0.54) per 10 dB(A) Leq,1h. Associations for estimated indoor noise were not more pronounced than for outdoor noise. Considering noise events in addition to equivalent sound pressure levels (Leq) only marginally improved the statistical models. Our study provides evidence that matching the nighttime noise exposure time window to the individual’s diurnal sleep-wake pattern results in a better estimate of detrimental nighttime noise effects on sleep. We found that noise exposure at the beginning and the end of the sleep is most crucial for sleep quality.

We performed the accuracy assessment of three different Normalized Difference Water Indices (NDWIs) in water bodies during April 2019, a period in which floods occurred in a large proportion of the Southwest of the Buenos Aires Province (Argentina). The accuracy of the estimations using spaceborne medium-resolution multi-spectral imaging, and the reliability of three NDWIs to highlight shallow water features in satellite images, was evaluated using a high resolution airbone imagery as ground-truth. It is shown that these indices computed using Landsat 8 and Sentinel-2 imagery are only loosely correlated to the actual flooded area in shallow waters. Indeed, NDWI values vary significantly depending on the satellite mission used and the type of index computed.

Improving air quality and reducing human exposure to unhealthy levels of airborne chemicals are important global missions, particularly in China. Satellite remote sensing offers a powerful tool to examine regional trends in NO2, thus providing a direct measure of key parameters that strongly affect surface air quality. To accurately resolve spatial gradients in NO2 concentration using satellite observations and thus understand local and regional aspects of air quality, a priori input data at sufficiently high spatial and temporal resolution to account for pixel-to-pixel variability in the characteristics of the land and atmosphere are required. In this paper, we adapt the Berkeley High Resolution product (BEHR v3.0A, v3.0B and v3.0C) and meteorological outputs from the Weather Research and Forecasting (WRF) model to describe column NO2 in southern China. The BEHR approach is particularly useful for places with large spatial variabilities and terrain height differences such as China. We retrieved tropospheric NO2 vertical column density (TVCD) within part of southern China, for four seasons of 2015, based upon satellite datasets from Ozone Monitoring Instrument (OMI). Retrieval results are validated by comparing with MAX-DOAS tropospheric column measurements conducted in Guangzhou. BEHR retrieval algorithms are more consistent with MAX-DOAS measurements than OMI-NASA retrieval, opening new windows into research questions that require high spatial resolution, for example retrieving NO2 vertical column and ground pollutant concentration in China and other countries.

Air pollution is a leading cause of death worldwide, and has a profound impact on the planet's climate and ecosystems. A substantial portion of air pollution is attributable to Ocean Going Vessels (OGVs). In light of this, international regulations have been put in place to mitigate air pollutant emissions from OGVs. While studies have indicated that these regulations can create significant health, environmental, and economic benefits, there remains a research gap regarding their specific impact on enhancing air quality. The aim of this study is to investigate how the implemented regulations have affected air quality in the Southern North Sea. The study found that the international regulations on ship emissions have successfully led to a decline in SO2 emissions from OGVs in the Southern North Sea, which resulted in a reduction of ambient SO2 concentrations inland, leading to positive effects on public health and the environment. However, it was projected that their proportion is tend to increase in the following years. Moreover, the study revealed that Exhaust Gas Cleaning Systems (EGCS) present significant concerns. They were significantly more frequently found to be non-compliant, and more alarmingly, they emit notably higher average levels of SO2. It also turned out that international regulations in the southern North Sea have less effect on the reduction of NOx emissions from OGVs than expected. The NOx emissions from OGVs will even account for an alarming 40% of the total domestic NOx emissions for the Belgian Region by 2030.

The paper delineates the developed vision system of the UR5 cobot and the operating algorithm of the robotic quality control station. The hardware-software architecture of the developed robotic station was shown, consisting of a UR5 cobot equipped with a web camera and a stationary industrial camera with a lighting system. Image processing and analysis algorithms were described, the method of control and communication between the station components was discussed, and two operating scenarios were presented as a single robotic station and a robotic line. Based on the results obtained, the level of measurement noise, accuracy, and repeatability of the developed vision system were estimated.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

Accurate measurement of solid precipitation (S) has a critical importance for proper understanding of the Earth’s hydrological cycle, validation of emerging technologies and weather prediction models, and developing parameterizations of severe weather elements such as visibility (Vis). However, measuring S is still a challenging problem mainly because of wind effects. The wind effects are normally mitigated by using a Double-Fence Automated Reference (DFAR) system to reduce the wind speed (Ug). To contribute towards addressing some of these issues we have analyzed data sets collected at a site located in Southern Ontario, Canada using several instruments. The instruments include two Geonor gauges, one placed inside a DFAR (SDFAR) and the other inside a double Alter shield (DASG), a Pluvio2 gauge inside a single Alter shield (SASP), a HotPlate, a PARSIVEL2 Disdrometer that measures S and fall velocity (V), and a FD12P senor that measures S and type and Vis. The results show that for the Ug observed in this study (Ug &lt; 6 ms-1), both DASG and SASP have similar collection efficiency (CE) of near 70%. The transfer functions (TF) for DASG and SASP as a function of Ug and also Ug, and V have been derived. The TF for the DASG that includes both Ug and V showed better agreement with observation than just Ug alone. The S measured using all the other instruments were correlated well with SDFAR, but the PARSIVEL2 and FD12P overestimated and underestimated the snow amount respectively as compared the SDFAR. However, the HotPlate captured similar amount of S as the SDFAR. According to this study, the SDFAR showed good correlation with Vis.

Deep neural networks (DNNs) have gained prominence in addressing regression problems, offering versatile architectural designs that cater to various applications. In the field of earthquake engineering, seismic response prediction is a critical area of study. Simplified models such as single-degree-of-freedom (SDOF) and multi-degree-of-freedom (MDOF) systems have traditionally provided valuable insights into structural behavior, known for their computational efficiency facilitating faster simulations. However, these models have notable limitations in capturing the nuanced nonlinear behavior of structures and the spatial variability of ground motions. This study focuses on leveraging ambient vibration (AV) measurements of buildings, combined with earthquake (EQ) time-history data, to create a predictive model using a neural network (NN) in image format. The primary objective is to predict a specific building's earthquake response accurately. The training dataset consists of 1,197 MDOF 2D shear models, generating a total of 32,319 training samples. To evaluate the performance of the proposed model, termed MLPER (Machine Learning based Prediction of building structures' Earthquake Response), several metrics are employed. These include mean absolute percentage error (MAPE) and mean deviation angle (MDA) for comparisons in the time domain. Additionally, we assess magnitude-squared coherence values and phase differences (Δφ) for comparisons in the frequency domain. This study underscores the potential of MLPER as a reliable tool for predicting building earthquake response, addressing the limitations of simplified models. By integrating AV measurements and EQ time-history data into a neural network framework, MLPER offers a promising avenue for enhancing our understanding of structural behavior during seismic events, ultimately contributing to improved earthquake resilience in building design and engineering.

In recent years, Parkinson's Disease (PD) as a progressive syndrome of the nervous system has become highly prevalent worldwide. In this study, a novel hybrid technique established by integrating a Multi-layer Perceptron Neural Network (MLP) with the Biogeography-based Optimization (BBO) to classify PD based on a series of biomedical voice measurements. BBO is employed to determine the optimal MLP parameters and boost prediction accuracy. The inputs comprised of 22 biomedical voice measurements. The proposed approach detects two PD statuses: 0– disease status and 1– reasonable control status. The performance of proposed methods compared with PSO, GA, ACO and ES method. The outcomes affirm that the MLP-BBO model exhibits higher precision and suitability for PD detection. The proposed diagnosis system as a type of speech algorithm detects early Parkinson’s symptoms, and consequently, it served as a promising new robust tool with excellent PD diagnosis performance.

Vibrational overtones in deeply bound molecules are sensitive probes for variation of the proton-to-electron mass ratio μ. In nonpolar molecules, these overtones may be driven as two-photon transitions. Here, we present procedures for experiments with O₂⁺, including state-preparation through photoionization, a two-photon probe, and detection. We calculate transition dipole moments between all X²П_g vibrational levels and those of the A²П_u excited electronic state. Using these dipole moments, we calculate two-photon transition rates and AC-Stark-shift systematics for the overtones. We estimate other systematic effects and statistical precision. Two-photon vibrational transitions in O₂⁺ provide multiple routes to improved searches for μ variation.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

A controlled ammonia (NH₃) release experiment was performed at a grassland site to quantify the effect of dry deposition, at the field scale between the source and the receptors (NH₃ measurement locations), on the estimates of emission rates by means of inverse dispersion modelling. NH₃ was released for 3 hours at a constant rate of Q = 6.29 mg s⁻¹ from a grid of 36 orifices spread over an area of 250 m². The increase in line-integrated NH₃ concentration was measured with open-path optical miniDOAS devices at different locations downwind of the artificial source. Using a backward Lagrangian stochastic (bLS) dispersion model (bLSmodelR), the fraction of the modelled release rate to the emitted NH₃ (Q_bLS/Q) was calculated from the measurements of the individual instruments. Q_bLS/Q was found to be systematically lower than 1, on average between 0.69 and 0.91, depending on the location of the receptor. We hypothesized that NH₃ dry deposition to grass and soil surfaces was the main factor responsible for the observed depletion of NH₃ between source and receptor. A dry deposition algorithm based on a deposition velocity approach was included in the bLS modelling. Model deposition velocities were evaluated from a ‘big‑leaf’ canopy resistance analogy. Canopy resistances (generally termed Rc) that provided Q_bLS/Q = 1 ranged from 75 to 290 s m⁻¹, showing that surface removal of NH₃ by dry deposition can plausibly explain the original underestimation of Q_bLS/Q. The inclusion of a dry deposition process in dispersion modelling is crucial for emission estimates, which are based on concentration measurements of depositing tracers downwind of homogeneous area sources or heterogeneously distributed hot spots, such as e.g. urine patches on pastures in the case of NH₃.

Neck circumference (NC), neck circumference to height ratio (NHtR) and neck circumference to weight ratio (NWtR) appear to be good candidates for the non-invasive management of non-alcoholic fatty liver disease (NAFLD). This study aimed to evaluate the ability of routine variables to assess and manage NAFLD in participants with obesity and NAFLD included in a 2-year nutritional intervention program. Anthropometric measurements, biochemical variables and imaging techniques were performed at different study time-points (baseline, 6, 12 and 24 months). The nutritional intervention significantly improved all anthropometric measurements as well as the glucose profile and the hepatic enzymes. NC and neck ratios combined with ALT levels and HOMA-IR showed good prediction ability for the hepatic fat content and hepatic steatosis at all the study time-points in a ROC analysis. The prediction ability of the combination panels improved when the weight loss variable was also considered. NC and neck ratios are easy anthropometric measurements that in combination with routine biochemical variables (ALT and HOMA-IR) showed good prediction ability of NAFLD. More research studies are necessary to validate the utility of these simple and easy variables as surrogate markers of NAFLD since their application could improve the prevention and management of this prevalent disease.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.