Wetlands are recognized as one of the world’s most valuable natural resources. With the increasing world population, human demands on wetland resources for agricultural expansion and urban development continue to increase. In addition, global climate change has pronounced impacts on wetland ecosystems through alterations in hydrological regimes. To better manage and conserve wetland resources, we need to know the distribution and extent of wetlands and monitor their dynamic changes. Wetland maps and inventories can provide crucial information for wetland conservation, restoration, and management. Geographic Information System (GIS) and remote sensing technologies have proven to be useful for mapping and monitoring wetland resources. Recent advances in geospatial technologies have greatly increased the availability of remotely sensed imagery with better and finer spatial, temporal, and spectral resolution. This chapter presents an introduction to the uses of GIS and remote sensing technologies for wetland mapping and monitoring. A case study is presented to demonstrate the use of high-resolution light detection and ranging (LiDAR) data and aerial photographs for mapping prairie potholes and surface hydrologic flow pathways.

Imaging lidars are one of the hottest topics in the optronics industry. The need to sense the surroundings of every autonomous vehicle has pushed forward a career to decide the final solution to be implemented. The diversity of state-of-the art approaches to the solution brings, however, a large uncertainty towards such decision. This results often in contradictory claims from different manufacturers and developers. Within this paper we intend to provide an introductory overview of the technology linked to imaging lidars for autonomous vehicles. We start with the main single-point measurement principles, and then present the different imaging strategies implemented 8 in the different solutions. An overview of the main components most frequently used in practice is also presented. Finally, a brief section on pending issues for lidar development has been included, 10 in order to discuss some of the problems which still need to be solved before an efficient final implementation.Beyond this introduction, the reader is provided with a detailed bibliography containing both relevant books and state of the art papers.

In this paper, the technical aspects of a multi-lidar instrument, the long-range WindScanner system, will be presented accompanied by an overview of the results from several field campaigns. The long-range WindScanner system consists of three spatially separated coherent Doppler scanning lidars and a remote master computer that coordinates them. The lidars were carefully engineered to perform arbitrary and time controlled scanning trajectories. Their wireless coordination via the master computer allows achieving and maintaining lidars’ synchronization within ten milliseconds. As a whole, the long-range WindScanner system can measure an entire wind field by emitting and directing three laser beams to intersect, and then by moving the beam intersection over the points of interest. The long-range WindScanner system was developed to tackle the need for high-quality observations of wind fields from scales of modern wind turbine and wind farms. It has been in operation since 2013.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

We present a comprehensive database of near-shore wind observations that were carried out during the experimental campaign of the RUNE project. RUNE aims at reducing the uncertainty of the near-shore wind resource estimates from model outputs by using lidar, ocean, and satellite observations. Here we concentrate in describing the lidar measurements. The campaign was conducted from November 2015 to February 2016 at the west coast of Denmark and comprises measurements from eight lidars, an ocean buoy and three types of satellites. The wind speed was estimated based on measurements from a scanning lidar performing PPIs, two scanning lidars performing dual synchronized scans, and five vertical profiling lidars, of which one was operating offshore on a floating platform. The availability of measurements is highest for the profiling lidars, followed by the lidar performing PPIs, those peforming the dual setup, and the lidar buoy. Analysis of the lidar measurements reveals good agreement between the estimated 10-m wind speeds, although the instruments used different scanning strategies and measured different volumes in the atmosphere. The campaign is characterized by strong westerlies with occasional storms.

Nacelle-based Doppler wind lidars have shown promising capabilities to assess power performance, detect yaw misalignment or perform feed-forward control. The power curve application requires uncertainty assessment. Traceable measurements and uncertainties of nacelle-based wind lidars can be obtained through a methodology applicable to any type of existing and upcoming nacelle lidar technology. The generic methodology consists in calibrating all the inputs of the wind field reconstruction algorithms of a lidar. These inputs are the line-of-sight velocity and the beam position, provided by the geometry of the scanning trajectory and the lidar inclination. The line-of-sight velocity is calibrated in atmospheric conditions by comparing it to a reference quantity based on classic instrumentation such as cup anemometers and wind vanes. The generic methodology was tested on two commercially developed lidars, one continuous wave and one pulsed systems, and provides consistent calibration results: linear regressions show a difference of ∼ 0.5 % between the lidar-measured and reference line-of-sight velocities. A comprehensive uncertainty procedure propagates the reference uncertainty to the lidar measurements. At a coverage factor of two, the estimated line-of-sight velocity uncertainty ranges from 3.2 % at 3 m s⁻¹ to 1.9 % at 16 m s⁻¹. Most of the line-of-sight velocity uncertainty originates from the reference: the cup anemometer uncertainty accounts for ∼ 90 % of the total uncertainty. The propagation of uncertainties to lidar-reconstructed wind characteristics can use analytical methods in simple cases, which we demonstrate through the example of a two-beam system. The newly developed calibration methodology allows robust evaluation of a nacelle lidar’s performance and uncertainties to be established in order to further be used for various wind turbines’ applications in confidence.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

The increasingly affordable price point of terrestrial laser scanners has led to a democratization of instrument availability, but the most common low-cost instruments have yet to be compared in terms of the consistency to measure forest structural attributes. Here, we compared two low-cost terrestrial laser scanners (TLS): the Leica BLK360 and the Faro Focus 120 3D. We evaluate the instruments in terms of point cloud quality, forest inventory estimates, tree-model reconstruction, and foliage profile reconstruction. Our direct comparison of the point clouds showed reduced noise in filtered Leica data. Tree diameter and height were consistent across instruments (4.4% and 1.4% error, respectively). Volumetric tree models were less consistent across instruments, with ~29% bias, depending on model reconstruction quality. In the process of comparing foliage profiles, we conducted a sensitivity analysis of factors affecting foliage profile estimates, showing a minimal effect from instrument maximum range (for forests less than ~50 m in height) and surprisingly little impact from degraded scan resolution. Filtered unstructured TLS point clouds must be artificially re-gridded to provide accurate foliage profiles. The factors evaluated in this comparison point towards necessary considerations for future low-cost laser scanner development and application in detecting forest structural parameters.

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.

This paper describes the first results of an Image Recognition Based Location (IRBL) for mobile application focusing on the procedure to generate a Database of range images (RGB-D). In an indoor environment, to estimate the camera position and orientation, a prior spatial knowledge of the surrounding is needed. In order to achieve this objective a complete 3D survey of two different environment (Bangbae metro station of Seoul and E.T.R.I. building in Daejeon – Republic of Korea) was performed using LiDAR (Light Detection And Ranging) instrument and the obtained scans were processed in order to obtain a spatial model of the environments. From this, two databases of reference images were generated using a specific software realized by the Geomatics group of Politecnico di Torino (ScanToRGBDImage). This tool allow to generate synthetically different RGB-D images) centered in the each scan position in the environment. Later, the external parameters (X, Y, Z, ω, φ, κ) and the range information extracted from the DB images retrieved, are used as reference information for pose estimation of a set of acquired mobile pictures in the IRBL procedure. In this paper the survey operations, the approach for generating the RGB-D images and the IRB strategy are reported. Finally the analysis of the results and the validation test are described.

Questions: Elevation, biodiversity, and forest structure are commonly correlated, but their relationships near the positive extremes of biodiversity and elevation are unclear. We asked 1) How does forest structure vary with elevation in a high biodiversity, high topographic complexity region? 2) Does forest structure predict vascular plant biodiversity? 3) Is plant biodiversity more strongly related to elevation or to forest structure? Location: Great Smoky Mountains National Park, USAMethods: We used terrestrial LiDAR scanning (TLS) to characterize vegetation structure in 12 forest plots. We combined two new canopy structural complexity metrics with traditional TLS-derived forest structural metrics and vascular plant biodiversity data to investigate correlations among forest structure metrics, biodiversity, and elevation. Results: Forest structure varied widely across plots spanning the elevational range of GRSM. Our new measures of canopy density (Depth) and structural complexity (σDepth) were sensitive to structural variations and effectively summarized horizontal and vertical dimensions of structural complexity. Vascular plant biodiversity was negatively correlated with elevation, and more strongly positively correlated with vegetation structure variables. Conclusions: The strong correlations we observed between canopy structural complexity and biodiversity suggest that structural complexity metrics could be used to assay plant biodiversity over large areas in concert with airborne and spaceborne platforms.

Collision avoidance is an important feature in advanced driver-assistance systems, aiming at providing correct, timely and reliable warnings before an imminent collision (objects, vehicles, pedestrians, etc.). A co-simulation framework is proposed in this paper to address the design and evaluation of collision avoidances in a cyber-physical system. The co-simulation framework is supported on the interaction between SCANeR and Matlab/Simulink. From the best of authors’ knowledge, two main contributions are reported in this paper. Firstly, the modelling and simulation of virtual on-chip LIDAR sensors in a cyber-physical system (CPS) considering traffic scenarios is presented. The CPS is designed and implemented in SCANeR. Secondly, an obstacle recognition library with three specific Artificial Intelligence-based methods is also designed based on sensory information database provided by SCANeR. Three methods for collision avoidance detection are considered, i.e.; a multi-layer perceptron neural network, a self-organization map and a support vector machine. Finally, a comparison among these methods for detecting obstacles before different weather conditions is done with very promising results in terms of accuracy. The best results are achieved using the multi-layer perceptron in sunny and fog conditions, the support vector machine in rainy and self-organized map in snowy conditions.

Active contour models present a robust segmentation approach which make efficient use of specific information about objects in the input data rather than processing all the data. They have been widely used in many applications including image segmentation, object boundary localisation, motion tracking, shape modelling, stereo matching and object reconstruction. In this paper, we investigate the potential of active contour models in extracting roads from Mobile Laser Scanning (MLS) data. The categorisation of active contours based on their mathematical representation and implementation are discussed in detail. We discuss an integrated version in which active contour models are combined to overcome their limitations. We review various active contour based methodologies which have been developed to extract roads and other features from LiDAR and digital imaging datasets. We present a small case study in which an integrated version of active contour models is applied to automatically extract road edges from MLS dataset. An accurate extraction of left and right edges from the tested road section validates the use of active contour models. The present study provides a valuable insight on the potential of active contours for extracting roads and other infrastructures from 3D LiDAR point cloud data.

This article proposes the use of a multi-scale and multi-sensor approach to collect and modelling 3D data concerning wide and complex areas in order to obtain a variety of metric information in the same 3D archive, based on a single coordinate system. The employment of these 3D georeferenced products is multifaceted and the fusion or integration among different sensors data, scales and resolutions is promising and could be useful for the generation of a model that could be defined as hybrid. The correct geometry, accuracy, radiometry and weight of the data models are hereby evaluated comparing integrated processes and results from Terrestrial Laser Scanner (TLS), Mobile Mapping System (MMS), Unmanned Aerial Vehicle (UAV), terrestrial photogrammetry, using Total Station (TS) and Global Navigation Satellite System (GNSS) as topographic survey. The entire analysis underlines the potentiality of the integration and fusion of different solutions and is a crucial part of the “Torino 1911” project whose main purpose is mapping and virtually reconstructing the 1911 Great Exhibition settled in the Valentino Park in Turin (Italy).

A new approach to the measurement with elastic lidar of depolarization produced by atmospheric aerosols is presented. The system uses two different telescopes: one for depolarization measurements and another for total-power measurements. The system architecture and principle of operation are described. The first experimental results are also presented, corresponding to a collection of atmospheric conditions over the city of Barcelona.

Mapping vegetation species is critical to facilitate related quantitative assessment, and for invasive plants mapping their distribution is important to enhance monitoring and controlling activities. Integrating high resolution multispectral remote sensing (RS) image and lidar (light detection and ranging) point clouds can provide robust features for vegetation mapping. However, using multiple source of high-resolution RS data for vegetation mapping at large spatial scale can be both computationally and sampling intensive. Here we designed a two-step classification workflow to decrease computational cost and sampling effort, and to increase classification accuracy by integrating multispectral and lidar data to derive spectral, textural, and structural features for mapping target vegetation species. We used this workflow to classify kudzu, an aggressive invasive vine, in the entire Knox County (1,362 km2) of Tennessee, the United States. Object-based image analysis was conducted in the workflow. The first-step classification used 320 kudzu samples and extensive coarsely labeled samples (based on national land cover) to generate an overprediction map of kudzu using random forest (RF). For the second step, 350 samples were randomly extracted from the overpredicted kudzu and labeled manually for the final prediction using RF and support vector machine (SVM). Computationally intensive features were only used for the second-step classification. SVM had constantly better accuracy than RF, and the Producer’s Accuracy, User’s Accuracy, and Kappa for the SVM model on kudzu was 0.94, 0.96, and 0.90, respectively. SVM predicted 1010 kudzu patches covering 1.29 km2 in Knox County. We found the sample size of kudzu used for algorithm training impacted the accuracy and number of kudzu predicted. The proposed workflow could also improve sampling efficiency and specificity. Our workflow had much higher accuracy than the traditional method conducted in this research, and could be easily implemented to map kudzu in other regions or other vegetation species.

A methodology for both accurate and smooth contour line generation from Light Detection and Ranging (LiDAR) point clouds is proposed in this paper. In order to improve the accuracy of contour lines in the area of forests, constrained triangulation networks with break lines are then constructed to generate contour lines. In break line extraction, a bi-threshold method for edge line detection is used to extract both complete and reliable break lines. A point clouds elevation adjustment with constrain of break lines and an interpolator considering a contour interval is proposed to improve the smoothness of contour lines. The proposed interpotator is also can avoid contour line intersection when contour lines are interpolated. Statistical parameters and shape index are then used to evaluate quantitatively the accuracy and smoothness of the resultant contour lines, which fill in the blank of contour lines evaluation in theory. The experiments show that high-quality contours in terms of smoothness and accuracy can be generated from LiDAR point clouds.

The study of vegetation community and structural change has been central to ecology for over a century, yet how disturbances reshape the physical structure of forest canopies remains relatively unknown. Moderate severity disturbance including fire, ice storms, insect and pathogen outbreaks, affects different canopy strata and plant species, which may give rise to variable structural outcomes and ecological consequences. Terrestrial lidar (light detection and ranging) offers an unprecedented view of the interior arrangement and distribution of canopy elements, permitting the derivation of multidimensional measures of canopy structure that describe several canopy structural traits with known linkages to ecosystem functioning. We used lidar-derived canopy structural measured within a machine learning framework to detect and differentiate among various disturbance agents, including moderate severity fire, ice storm damage, age-related senescence, hemlock woolly adelgid, beech bark disease, and chronic acidification. We found that disturbance agents such as fire and ice storms primarily affected the amount and position of vegetation within canopies, while acidification, pathogen and insect infestation, and senescence altered canopy arrangement and complexity. Only two of the six disturbance agents significantly reduced leaf area, indicating that this commonly quantified canopy feature is insufficient to characterize many moderate severity disturbances. Rather, measures of canopy structure, including those that describe multidimensional change, are needed to characterize disturbance at moderate severities because structural changes from these events are spatially and quantitatively variable. Our findings suggest that standard disturbance detection methods, such as optical based remote sensing platforms, may currently be limited in their ability to detect, differentiate, and characterize disturbance. Further, we conclude that a more broadly inclusive definition of ecological disturbance that incorporates multiple aspects of canopy structure change will improve the modeling, detection, and prediction of functional implications of moderate severity disturbance.

While lidar-based forest inventory methods have been widely demonstrated, prediction of tree diameters with lidar is not well understood. The performance metrics typically used in studies for prediction of diameters can be difficult to interpret and may not support comparative inferences between sampling designs or study areas. We evaluate a variety of lidar and k nearest neighbor (k-NN) strategies for prediction of tree diameter distributions using two indices which are easier to interpret and compare. The indices are based on the coefficient of determination (R²), and root mean square deviation (RMSD). These indices facilitate comparisons with alternative (non-lidar) inventory strategies, and with other project areas. We evaluate k nearest neighbors (k-NN) dbh density (relative frequency by dbh class) prediction strategies with lidar for 190 training plots distribute across the 800 km² Savannah River Site in South Carolina, USA. We evaluate the performance of k-NN with respect to distance metrics, number of neighbors, predictor sets, and response sets. Amongst the examined strategies we found Mahalanobis distance with k = 3 neighbors performed best according to a number of criteria.

The market for autonomous vehicles (AV) is expected to experience significant growth over the coming decades and to revolutionize the future of transportation and mobility. The AV is a vehicle that is capable of perceiving its environment and perform driving tasks safely and efficiently with little or no human intervention and is anticipated to eventually replace conventional vehicles. Self-driving vehicles employ various sensors to sense and perceive their surroundings and, also rely on advances in 5G communication technology to achieve this objective. Sensors are fundamental to the perception of surroundings and the development of sensor technologies associated with AVs has advanced at a significant pace in recent years. Despite remarkable advancements, sensors can still fail to operate as required, due to for example, hardware defects, noise and environment conditions. Hence, it is not desirable to rely on a single sensor for any autonomous driving task. The practical approaches shown in recent research is to incorporate multiple, complementary sensors to overcome the shortcomings of individual sensors operating independently. This article reviews the technical performance and capabilities of sensors applicable to autonomous vehicles, mainly focusing on vision cameras, LiDAR and Radar sensors. The review also considers the compatibility of sensors with various software systems enabling the multi-sensor fusion approach for obstacle detection. This review article concludes by highlighting some of the challenges and possible future research directions.

Terrestrial LiDAR becomes more and more popular to estimate leaf and plant area density. Voxel-based approaches account for this vegetation heterogeneity and significant work has been done in this recent research field, but no general theoretical analysis is available. Although estimators have been proposed and several causes of biases have been identified, their consistency and efficiency have not been evaluated. Also, confidence intervals are almost never provided. In the present paper, we solve the transmittance equation and use the Maximum Likelihood Estimation (MLE), to derive unbiased estimators and confidence intervals for the attenuation coefficient, which is proportional to leaf area density. The new estimators and confidence intervals are defined at voxel scale, and account for the number of beams crossing the voxel, the inequality of path lengths in voxel, the size of vegetation elements, as well as for the variability of element positions between vegetation samples. They are completed by numerous numerical simulations for the evaluation of estimator consistency and efficiency, as well as the assessment of the coverage probabilities of confidence intervals. • Although commonly used when the beam number is low, the usual estimators are strongly biased and the 95% confidence intervals can be ≈±100% of the estimate. • Our unbiased estimators are consistent in a wider range of validity than the usual ones, especially for the unbiased MLE, which is consistent when the beam number is as low as 5. The unbiased MLE is efficient, meaning it reaches the lowest residual errors that can be expected (for an unbiased estimator). Also the unbiased MLE does not require any bias correction when path lengths are unequal. • When elements are small (or voxel is large), 103 beams entering the voxel leads to some confidence intervals ≈±10%, but when elements are larger (or voxel smaller), it can remain wider than ±50%, even for a large beam number. This is explained by the variability of element positions between vegetation samples. Such a result shows that a significant part of residual error can be explained by random effects. • Confidence intervals are much smaller (±5 to 10%) when LAD estimates are averaged over several small voxels, typically within a horizontal layer or in the crown of individual plants. In this context, our unbiased estimators show a reduction of 50% of the radius of confidence intervals, in comparison to usual estimators. Our study provides some new ready-to-use estimators and confidence intervals for attenuation coefficients, which are consistent and efficient within a fairly large range of parameter values. The consistency is achieved for a low beam number, which is promising for application to airborne LiDAR data. They entail to raise the level of understanding and confidence on LAD estimation. Among other applications, their usage should help determine the most suitable voxel size, for given vegetation types and scanning density, whereas existing guidelines are highly variable among studies, probably because of differences in vegetation, scanning design and estimators.

Impervious surface mapping with high-resolution remote sensing imagery has attracted increasing interest as it can provide detailed information for urban structure and distribution. Previous studies have suggested that the combination of LiDAR data and high-resolution imagery for impervious surface mapping performs better than using only high-resolution imagery. However, due to the high cost of the acquisition of LiDAR data, it is difficult to obtain the multi-sensor remote sensing data acquired at the same acquisition time for impervious surface mapping. Consequently, real landscape changes between multi-sensor remote sensing data at different acquisition times would lead to the error of misclassification in impervious surface mapping. This issue has mostly been neglected in previous works. Furthermore, the observation differences generated from multi-sensor data, including the problems of misregistration, missing data in LiDAR data, and shadow in high-resolution images would also challenge the final mapping result in the fusion of LiDAR data and high-resolution images. In order to conquer these problems, we propose an improved impervious surface mapping method incorporating both LiDAR data and high-resolution imagery at different acquisition times in consideration of real landscape changes and observation differences. In the proposed method, a multi-sensor change detection by supervised multivariate alteration detection is employed to obtain changed areas and misregistration areas. The no-data areas in the LiDAR data and the shadow areas in the high-resolution imagery are extracted by independent classification yielded by its corresponding single sensor data. Finally, an object-based post-classification fusion is proposed to take advantage of independent classification results with single-sensor data and the joint classification result with stacked multi-sensor data. Experiments covering the study site in Buffalo, NY, USA demonstrate that our method can accurately detect landscape changes and obviously improve the performance of impervious surface mapping.

Historical forest management practices in the southwestern US have left forests prone to high intensity, stand-replacement fires. Effective management to reduce the cost and impact of forest-fire management and allow fires to burn freely without negative impact depends on detailed knowledge of stand composition, in particular, above-ground biomass (AGB). Lidar-based modeling techniques provide opportunities to reduce costs and increase ability of managers to monitor AGB and other forest metrics. Using Bayesian Model Averaging (BMA), we develop a regionally applicable lidar-based statistical model for Ponderosa pine and mixed conifer forest systems of the southwestern USA, using previously collected field data. The selected regional model includes a mid and low canopy height metric, a canopy cover, and height distribution term. It explains 72% of the variability in field estimates of AGB, and the RMSE of the two independent validation data sets are 23.25 and 32.82 Mg/ha. The regional model developed is structured in accordance with previously described models fit to local data, and performs equivalently to models designed for smaller scale application. Developing regional models for broad scale application provides a cost-effective, robust approach for managers to monitor and plan adaptively at the landscape scale.

Forest canopy structure (CS) controls many ecosystem functions and is highly variable across landscapes, but the magnitude and scale of this variation is not well understood. We used a portable canopy lidar system to characterize variation in five categories of CS along N = 3 transects (140–800 m long) at each of six forested landscapes within the eastern USA. The cumulative coefficient of variation was calculated for subsegments of each transect to determine the point of stability for individual CS metrics. We then quantified the scale at which CS is autocorrelated using Moran’s I in an Incremental Autocorrelation analysis. All CS metrics reached stable values within 300 m but varied substantially within and among forested landscapes. A stable point of 300 m for CS metrics corresponds with the spatial extent that many ecosystem functions are measured and modeled. Additionally, CS metrics were spatially autocorrelated at 40 to 88 m, suggesting that patch scale disturbance or environmental factors drive these patterns. Our study shows CS is heterogeneous across temperate forest landscapes at the scale of 10’s of meters, requiring a resolution of this size for upscaling CS with remote sensing to large spatial scales.

Degradation of environment quality is currently the prime cause of the recent occurrence of natural disasters; it also contributes in the increase of the area that is prone to natural disasters. This research is aimed to map the potential of areas around Pesanggrahan river in DKI Jakarta by segmenting the Digital Elevation Model derived from LIDAR data. The objective of this segmentation is to find the watershed lines of the DEM image. Data processing in this research is using LIDAR data which take the ground surface data, which is overlaid with Jakarta river map and subsequently, the data is then segmented the image. The expected result of the research is the flood potential area information, especially along the Pesanggrahan river in South Jakarta.

In this paper we illustrate a new, simple and complementary ground-based methodology to retrieve the vertically resolved atmospheric precipitation intensity through a synergy between measurements from the National Aeronautics and Space Administration (NASA) Micropulse Lidar network (MPLNET), an analytical model solution and ground-based disdrometer measurements. The presented results are obtained at two mid-latitude MPLNET permanent observational sites, located respectively at NASA Goddard Space Flight Center, USA, and at the Universitat Politècnica de Catalunya, Barcelona, Spain. The methodology is suitable to be applied to existing and/or future lidar/ceilometer networks with the main objective of either providing near-real time (3h latency) rainfall intensity measurements and/or to validate satellite missions, especially for critical light precipitation (<3 mm hr⁻¹).

Depth maps produced by LiDAR based approaches are sparse. Even high-end LiDAR sensors produce highly sparse depth maps, which are also noisy around the object boundaries. Depth completion is the task of generating a dense depth map from a sparse depth map. While the traditional approaches focus on directly completing this sparsity from the sparse depth maps, modern techniques use RGB images as a guidance tool to resolve this problem. Whilst many others rely on affinity matrices for depth completion. Based on these approaches, we have sub-divided the literature into two major categories; traditional approaches and backbone-based approaches. The latter is further sub-divided into two-branch, and spatial propagation approaches. The two-branch approaches still have a sub-category named guided-kernel approaches. In this paper, for the first time ever we present a comprehensive survey of depth completion methods. We present a novel taxonomy of depth completion approaches, review and detail different state-of-the art techniques within each category for depth completion of LiDAR data, and provide quantitative results for the approaches on KITTI and NYUv2 depth completion benchmark datasets.

Nowadays, the research and development of on-chip LiDAR sensors for vehicle collision avoidance is growing very fast. Therefore, the assessment of the reliability in obstacle detection using the information provided by LiDAR sensors has become a key issue to be explored by the scientific community. This paper presents the design and implementation of a self-tuning method in order to maximize the reliability of an Internet-of-Things sensors network and to minimize the number of sensors to localize with the required accuracy obstacles by a detection threshold. In order to achieve this goal, models that predict accuracy (i.e., prediction error) for object localization using data collected by LIDAR sensors are designed and implemented in Webots Automobile 3D simulation tool. The approach is based on combining different techniques. Firstly, point-cloud clustering technique and an error prediction model library composed by a multilayer perceptron neural network with backpropagation, k-nearest neighbors and linear regression are explored. Secondly the above-mentioned techniques for modeling are also combined with a supervised and reinforcement machine learning technique, Q-learning in order to minimize the detection threshold. In addition, a IoT driving assistance simulated scenario with a LiDAR sensor network is designed in order to validate the prediction model and the optimal configuration of the sensor network to guarantee reliability in obstacle localization. The results demonstrate that the self-tuning method is appropriate to increase the reliability of the sensor network whereas minimizing the detection threshold

The Greenland Ice Sheet is now the largest land ice contributor to global sea level rise, largely driven by increased surface meltwater runoff from the ablation zone, i.e. areas of the ice sheet where annual mass losses exceed gains. This small but critically important area of the ice sheet has expanded in size by ~50% since the early 1960s, and satellite remote sensing is a powerful tool for monitoring the physical processes that influence its surface mass balance. This review synthesizes key remote sensing methods and scientific findings from satellite remote sensing of the Greenland Ice Sheet ablation zone, covering progress in 1) radar altimetry, 2) laser (lidar) altimetry, 3) gravimetry, 4) multispectral optical imagery and, 5) microwave and thermal imagery. Physical characteristics and quantities examined include surface elevation change, gravimetric mass balance, reflectance, albedo, and mapping of surface melt extent and glaciological facies and zones. The review concludes that future progress will benefit most from methods that combine multi-sensor, multi-wavelength, and cross-platform datasets designed to discriminate the widely varying surface processes in the ablation zone. Specific examples include fusing laser altimetry, radar altimetry, and optical stereophotogrammetry to enhance spatial measurement density, cross-validate surface elevation change, and diagnose radar elevation bias; fusing optical imagery, radar imagery, and microwave scatterometry to discriminate between snow, liquid water, refrozen meltwater, and bare ice near the equilibrium line altitude; combining optical reflectance with laser altimetry to map supraglacial lake, stream, and crevasse bathymetry; and monitoring the inland migration of snowlines, surface melt extent, and supraglacial hydrologic features.

Topographic mapping using stereo plotting is not effective because it takes much time and labor-intensive. Thus, this research was conducted to find the effective way to extract building footprint for mapping acceleration. Building extraction method in this process comprises four steps: ground / non-ground filtering, building classification, segmentation, and building extraction. Non-ground points from filtering process were classified as building with the algorithm based on multi-scale local dimensionality to separate points at the maximum separability plane. Segmentation using segment growing was used to separate each building, so edge detection could be conducted for each segment to create boundary of each building. Lastly, building extraction was conducted through three steps: edge points detection, building delineation, and building regularization. With 10 samples and step 0.5, classification resulted quality and miss factor of 0.597 and 0.524, respectively. The quality was improved by segmentation process to 0.604, while miss factor was getting worse to 0.561. Meanwhile, on average shape index value from extracted building had 0.02 difference and the number of errors was 30% for line segment comparison. Regarding positional accuracy using centroid accuracy assessment, this method could produce RMSE of 1.169 meters.

In terrain analysis and hydrological modeling, surface depressions (or sinks) in a digital elevation model (DEM) are commonly treated as artifacts and thus filled and removed to create a depressionless DEM. Various algorithms have been developed to identify and fill depressions in DEMs during the past decades. However, few studies have attempted to delineate and quantify the nested hierarchy of actual depressions, which can provide crucial information for characterizing surface hydrologic connectivity and simulating the fill-merge-spill hydrological process. In this paper, we present an innovative and efficient algorithm for delineating and quantifying nested depressions in DEMs using the level-set method based on graph theory. The proposed level-set method emulates water level decreasing from the spill point along the depression boundary to the lowest point at the bottom of a depression. By tracing the dynamic topological changes (i.e., depression splitting/merging) within a compound depression, the level-set method can construct topological graphs and derive geometric properties of the nested depressions. The experimental results of two fine-resolution LiDAR-derived DEMs show that the raster-based level-set algorithm is much more efficient (~150 times faster) than the vector-based contour tree method. The proposed level-set algorithm has great potential for being applied to large-scale ecohydrological analysis and watershed modeling.

The application of 3D LiDAR technology has become increasingly extensive in tunnel monitoring due to the large density and high accuracy of the acquired spatial data. The proposed processing method aims at circle tunnels and provides a clear workflow to automatically process raw point data and easily interpretable results to analyze tunnel health state. The proposed automatic processing method employs a series of algorithms to extract point cloud of a single tunnel segment without obvious noise from entire raw tunnel point cloud mainly by three steps: axis acquisition, segments extraction and denoising. Tunnel axis is extracted by fitting boundaries of the tunnel point cloud rejection in plane with RANSAC algorithm. With guidance of axis, the entire preprocessed tunnel point cloud is segmented by equal division to get a section of tunnel point cloud which corresponds to a single tunnel segment. Then the noise in every single point cloud segment is removed by clustering algorithm twice, based on distance and intensity. Finally, clean point clouds of tunnel segments are processed by effective deformation extraction processor to get ovality and three-dimensional deformation nephogram.

Indigenous forests cover 24% of New Zealand and provide valuable ecosystem services. However, a national map of forest types, that is, physiognomic types, which would benefit conservation management, does not currently exist at an appropriate level of detail. While traditional forest classification approaches from remote sensing data are based on spectral information alone, the joint use of space-based optical imagery and structural information from synthetic aperture radar (SAR) and canopy metrics from air-borne Light Detection and Ranging (LiDAR) facilitates more detailed and accurate classifications of forest structure. We present a support vector machine (SVM) classification using data from ESA’s Sentinel-1 and 2 missions, ALOS PALSAR, and airborne LiDAR to produce a regional map of physiognomic types of indigenous forest in New Zealand. A five-fold cross-validation of ground data showed that the highest classification accuracy of 80.9% is achieved for bands 2, 3, 4, 5, 8, 11, and 12 from Sentinel-2, the ratio of bands VH and VV from Sentinel-1, HH from PALSAR, and mean canopy height and 97th percentile canopy height from LiDAR. The classification based on the optical bands alone was 73.1% accurate and the addition of structural metrics from SAR and LiDAR increased accuracy by 7.8%. The classification accuracy is sufficient for many management applications for indigenous forest in New Zealand, including biodiversity management, carbon inventory, pest control, ungulate management, and disease management. National application of the method will be possible in several years, once national LiDAR coverage is achieved, and a national canopy height model is available.

Data on the atmospheric gas concentrations can be received with high efficiency and on a large spatial scale only from remote laser sounding instruments. The remote laser techniques with the use of lidars are widely used in the study of the atmosphere and control of its state. The aims of this work are the design and test in numerical and field experiments of a DIAL OPO lidar system based on KTA and KTP crystals for gas analysis of the atmosphere. Lidar measurements of atmospheric gases in the near/mid infrared region have been numerically simulated. The differential absorption lidar system based on optical parametric oscillators with nonlinear KTA and KTP crystals which allow laser radiation tuning both in the near and in the middle IR spectral region is described; it allows tuning laser radiation in the near/mid-IR wavelength regions. Lidar echo signals have been experimentally recorded in the 1.8–2.5 and 3–4 m wavelength ranges. The results of H2O and CO2 profile measurements along the surface sounding path are presented.

Currently, the most important challenge in any assessment of state-of-the-art sensor technology and its reliability is to achieve road traffic safety targets. The research reported in this paper is focused on the design of a procedure for evaluating the reliability of Internet-of-Things (IoT) sensors and the use of a Cyber-Physical System (CPS) for the implementation of that evaluation procedure to gauge reliability. An important requirement for the generation of real critical situations under safety conditions is the capability of managing a co-simulation environment, in which both real and virtual data sensory information can be processed. An IoT case study that consists of a LiDAR-based collaborative map is then proposed, in which both real and virtual computing nodes with their corresponding sensors exchange information. Specifically, the sensor chosen for this study is a Ibeo Lux 4-layer LiDAR sensor with IoT added capabilities. Implementation is through an artificial-intelligence-based modeling library for sensor data-prediction error, at a local level, and a self-learning-based decision-making model supported on a Q-learning method, at a global level. Its aim is to determine the best model behavior and to trigger the updating procedure, if required. Finally, an experimental evaluation of this framework is also performed using simulated and real data

In the coded pulse scanning light detection and ranging (LIDAR) system, the number of laser pulses used at a given measurement point changes depending on the modulation and the method of spreading used in optical code-division multiple access (OCDMA). The number of laser pulses determines the pulse width, output power, and duration of the pulse transmission of a measurement point. These parameters determine the maximum measurement distance of the laser and the number of measurement points that can be employed per second. In this paper, we evaluate the performance and characteristics of combinations of modulation and spreading technology that can be used for OCDMA, and study optimal combinations according to varying operating environments.

Storm Ophelia made landfall over Ireland as an extra-tropical storm on the morning of the 16th of October 2017. The storm caused major power outages, lifted roofs, caused coastal flooding in Ireland, and resulted in the loss of three lives. A model’s capability to forecast extreme weather events such as Storm Ophelia is of utmost importance and now with a changing climate, it becomes more important to improve and enhance model forecasting capability. The Weather Research and Forecasting (WRF) model V3.9 has been configured for the Irish domain and this study presents a preliminary evaluation of the Model during Storm Ophelia. Simulated wind speed and direction were compared with hourly remote sensing (lidar) and in-situ (wind speed and wind direction at 10m) observations at the coastal site of Mace Head Atmospheric Research Station on the West coast of Ireland (53.33◦ N, 9.90 49 ◦ W). The model simulation has generally small biases in the simulated wind speed and wind direction during this case study. The model also realistically simulated the magnitude and geographical distribution of the wind speed and wind direction observed during Ophelia.

Fire-tolerant eucalypt forests of south eastern Australia are assumed to fully recover from even the most intense fires but surprisingly very few studies have quantitatively assessed that recovery. Accurate assessment of horizontal and vertical attributes of tree crowns after fire is essential to understand the fire’s legacy effects on tree growth and on forest structure. In this study, we quantitatively assessed individual tree crowns 8.5 years after a 2009 wildfire that burnt extensive areas of eucalypt forest in temperate Australia. We used airborne lidar data validated with field measurements to estimate multiple metrics that quantified the cover, density, and vertical distribution of individual-tree crowns in 51 plots of 0.05 ha in fire-tolerant eucalypt forest across four wildfire severity types (unburnt, low, moderate, high). Significant differences in the field-assessed mean height of fire scarring as a proportion of tree height, and in the proportions of trees with epicormic (stem) resprouts were consistent with the gradation in fire severity. Linear mixed-effects models indicated persistent effects of both moderate- and high-severity wildfire on tree crown architecture. Trees at high-severity sites had significantly less crown projection area and live crown width as a proportion of total crown width than those at unburnt and low-severity sites. Significant differences in lidar-based metrics (crown cover, evenness, leaf area density profiles) indicated that tree crowns at moderate- and high-severity sites were comparatively narrow and more evenly distributed down the tree stem. These conical-shaped crowns contrasted sharply with the rounded crowns of trees at unburnt and low-severity sites, and likely influenced both tree productivity and the accuracy of biomass allometric equations for nearly a decade after the fire. Our data provide a clear example of the utility of airborne lidar data for quantifying the impacts of disturbances at the scale of individual trees. Quantified effects of contrasting fire severities on the structure of resprouter tree crowns provide a strong basis for interpreting post-fire patterns in forest canopies and vegetation profiles in lidar and other remotely-sensed data at larger scales.

The high-resolution bistatic lidar developed at the Physikalisch-Technische Bundesanstalt (PTB) aims to overcome the limitations of conventional monostatic lidar technology which is widely used for wind velocity measurements in wind energy and meteorology applications. Due to the large measurement volume of a combined optical transmitter and receiver tilting in multiple directions, monostatic lidar generally has poor spatial and temporal resolution. It also exhibits large measurement uncertainty when operated in inhomogeneous flow, for instance, over complex terrain. In contrast, PTB’s bistatic lidar uses three dedicated receivers arranged around a central transmitter, resulting in an exceptionally small measurement volume. The coherent detection and modulation schemes used allow the detection of backscattered, Doppler shifted light down to the scale of single aerosols, realising the simultaneous measurement of all three wind velocity components. This paper outlines design details and the theory of operation of PTB’s bistatic lidar and provides an overview of selected comparative measurements. The results of these measurements have shown that the measurement uncertainty of PTB’s bistatic lidar is well within the measurement uncertainty of traditional cup anemometers, while being fully independent of its site and traceable to the SI units. This allows its use as a transfer standard for the calibration of other remote sensing devices. Overall, PTB’s bistatic lidar shows great potential to universally improve the capability and accuracy of wind velocity measurements, such as for the investigation of highly dynamic flow processes upstream and in the wake of wind turbines.

Forests are critical in regulating the world’s climate and they maintain overall Earth’s energy balance. The variability in forest canopy structure, topography and underneath vegetation background condition creates uncertainty in the estimation and modelling of Earth’s surface radiation particularly for boreal regions in high latitude. We studied seasonal variation in surface reflectance with respect to land cover classes, canopy structures, and topography in a boreal region of Alaska by fusing together Landsat 8 surface reflectance and LiDAR-derived canopy matrices. Our study shows that canopy structure and topography interplay and influence surface reflectance in a complex way particularly during the snow season. Topographic aspect and elevation control vegetation growth, type and structure. The southern slope is featured with more deciduous and taller trees having greater rugosity than the northern slope. Higher elevation is associated with taller trees for both vegetation types, particularly in the southern slope. In general, surface reflectance shows similar relationships with canopy cover, height and rugosity, mainly due to close relationships between these parameters. Surface reflectance decreases with canopy cover, tree height, and rugosity especially for evergreen forest. Deciduous forest shows larger variability of surface reflectance, particularly in March, mainly due to the mixing effect of snow and vegetation. The relationship between vegetation structure and surface reflectance is greatly impacted by topography. The negative relationship between elevation and surface reflectance may be due to taller and denser vegetation distribution in higher elevation. Surface reflectance in the southern slope is slightly larger than the northern slope for both deciduous and evergreen forest. The shadow effect from topography and tree crowns on surface reflectance play a different role for deciduous and evergreen forests. For deciduous forest, topographic shadow effect on surface reflectance is stronger than from tree shadowing in all seasons. For evergreen forest, shadow effects from topography and tree crowns on surface reflectance are both equally dominant, however tree shadow effect is more significant in March than in May and August. The generalized additive models (GAM) based on non-linear relationships between response (surface reflectance) and predictor (canopy structures and topography) variables confirms such observations. Our study not only provides accurate quantification of surface radiation budget but also helps in parametrization of climate change models.

The amount and spatial distribution of foliage in a tree canopy have fundamental functions in ecosystems as they affect energy and mass fluxes through photosynthesis and transpiration. They are usually described by the Leaf Area Index (LAI) and the Leaf Area Density (LAD), which can be measured through a variety of methods, including voxel-based methods applied to LiDAR point clouds. A theoretical study recently compared the numerical errors arising from different voxel-based estimation methods for Plant Area Density (PAD) based on Beer’s law-based, contact frequency and Maximum-Likelihood Estimation, showing that the bias-corrected Maximum Likelihood Estimator was theoretically the most efficient. However, this earlier study i) ignored wood volumes; ii) neglected vegetation clumping inside the voxel; iii) ignored instrument characteristics in terms of effective footprint, iv) was limited to a single viewpoint. In practice, retrieving LAD from PAD is not straightforward, vegetation is not randomly distributed in volumes of interest, beams are divergent and forestry plots are usually sampled from more than one viewpoint, to mitigate the effect of occlusion. In the present short communication, we extend the previous efficient formulation to actual field conditions to i) account for the presence of both wood volumes and wood hits, ii) rigorously include correction terms for vegetation and instrument characteristics, iii) integrate multiview data. A numerical comparison with other methods commonly used to combine information from different viewpoints led to error reduction, especially in poorly-explored volumes, which are frequent in actual canopies. Beyond its concision, completeness and efficiency, this new formulation -which can be applied to multiview TLS, but also UAV LiDAR scanning - can help reducing errors in LAD estimation.

The vulnerability of alpine environments to climate change presses an urgent need to accurately model and understand these ecosystems. Popularity in use of digital elevation models (DEMs) to derive proxy environmental variables has increased over the past decade, particularly as DEMs are relatively cheaply acquired at very high resolutions (VHR; <1m spatial resolution). Here, we implement a multiscale framework and compare DEM-derived variables produced by Light Detection and Ranging (LiDAR) and stereo-photogrammetry (PHOTO) methods, with the aims of assessing their relevance and utility in species distribution modelling (SDM). Using a case study on the arctic-alpine plant Arabis alpina in two valleys in the western Swiss Alps, we show that both LiDAR and PHOTO technologies can be relevant for producing DEM-derived variables for use in SDMs. We demonstrate that PHOTO DEMs rivalled the accuracy of LiDAR, putting the current paradigm of LiDAR being the more accurate of the two methods into question. We obtained DEMs at spatial resolutions of 6.25cm-8m for PHOTO and 50cm-32m for LiDAR, where we determined that the optimal spatial resolutions of DEM-derived variables in SDM were between 1 and 32m, depending on the variable and site characteristics. We found that the reduced extent of PHOTO DEMs altered the calculations of all derived variables, which had particular consequences on their relevance at the site with heterogenous terrain. However, for the homogenous site, we found that SDMs based on PHOTO-derived variables generally had higher predictive powers than those derived from LiDAR at matching resolutions. From our results, we recommend carefully considering the required DEM extent to produce relevant derived variables. We also advocate implementing a multiscale framework to appropriately assess the ecological relevance of derived variables, where we caution against the use of VHR-DEMs finer than 50cm in such studies.

The accuracy of wind field simulation and prediction is one of the most significant parameters in the field of atmospheric science and wind energy. Limited by the observation data, there are few researches on wind energy development. A 3D Doppler wind lidar (DWL) providing the high-vertical-resolution wind data over the urban complex underlying surface in February 2018 was employed to evaluated the accuracy of vertical wind field simulation systematically for the first time. 11 PBL schemes of the Weather Research and Forecasting Model (WRF) were employed in simulation. The model results were evaluated in groups separated by weather (sunny days, haze days and windy days), observation height layers, and various observation wind speeds. The test results presented that the vertical layer altitude of the observation point position was the most important factor. The simulation is fairly well at a height of 1000-2000m, as most of the relative mean bias of wind speed and wind direction are less than 20% and 6% respectively. Below 1000 m, the wind speed and direction biases are about 30%-150% m.s-1 and 6%-30% respectively. Moreover, when the observed wind speed was lower than 5 m.s-1, the bias were usually large, and the wind speed relative mean bias is up to 50-300%. In addition, the accuracy of simulated wind profile is better in 10-15m.s-1 than other speed ranges, and is better up 1000m than below 1000m in the boundary layer. We see that the WRF boundary layer schemes have different applicability to different weather conditions. The WRF boundary layer schemes have significant differences in wind field simulation with larger error under the complex topography. A PBL scheme is not likely to maintain its advantages in the long term under different conditions including altitude and weather conditions.

Recent studies indicate that the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) aboard the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) satellite provides valuable information about ocean phytoplankton distributions. CALIOP’s attenuated backscatter coefficients, measured at 532 nm in receiver channels oriented parallel and perpendicular to the laser’s linear polarization plane, are significantly improved in the Version 4 data product. However, due to non-ideal instrument effects, a small fraction of the backscattered optical power polarized parallel to the receiver polarization reference plane is misdirected into the perpendicular channel, and vice versa. This effect, known as polarization crosstalk, typically causes the measured perpendicular signal to be higher than its true value and the measured parallel signal to be lower than its true value. Therefore, the ocean optical properties derived directly from CALIOP’s measured signals will be biased if the polarization crosstalk effect is not taken into account. This paper presents methods that can be used to estimate the CALIOP crosstalk effects from on-orbit measurements. The global ocean depolarization ratios calculated both before and after removing the crosstalk effects are compared. Using CALIOP crosstalk-corrected signals is highly recommended for all ocean subsurface studies.

In the aftermath of pyroclastic-flow –dominated eruptions, lahars are the main geomorphic agent, but at the decadal scale, different sets of processes take place in the volcanic sediment cascade. At Unzen Volcano, in the Gokurakudani Gully we investigated the geomorphologic evolution and how the topographic change and the sediment change over time is controlling this transition. For this purpose, a combination of LiDAR data, aerial photography and photogrammetry, Ground Penetrating Radar and sediment grain-size analysis was done. The results show chocking zones and zones of enlargement of the gully, partly controlled by pre-eruption topography, but also by the overlapping patterns of the pyroclastic flow deposits of 1990 – 1995. The Ground Penetrating Radar revealed that on top of the typical lahar structure at the bottom of the gully, side-wall collapses were trapping finer sandy sediments formed in relatively low-energy deposition environment. This shows that secondary processes are taking place in the sediment transport process, on top of lahar activity, but also that these temporary dams may be a source of sudden sediment and water release, leading to lahars. Finally, the sediments from the gully walls are being preferentially oozed out of the pyroclastic-flow deposit, meaning that over longer period of time, there may be a lack of fines, increasing permeability and reducing internal pore-pressure needed for lahar triggering. It also poses the important question of how much of a past-event one can understand from outcrops in coarse heterometric material, as the deposit structure can remain, even after loosing part of its fine material.

The world is facing a great technological transformation towards full autonomous vehicles, where optimists predict that by 2030, autonomous vehicles will be sufficiently reliable, affordable and common to displace most human driving. To cope with these trends, reliable perception systems must enable vehicles to hear and see all the surroundings, being light detection and ranging (LiDAR) sensors a key instrument for recreating a 3D visualization of the world in real time. However, perception systems must rely in accurate measurements of the environment. Thus, sensors must be calibrated and benchmarked before being placed on the market or assembled in a car. This article presents an Evaluation and Testing Platform for Automotive LiDAR sensors with the main goal of testing not only commercially available sensors, but also sensor prototypes currently under development in Bosch Automotive Electronics division. The testing system can benchmark any LiDAR sensor under different conditions, recreating the expected driving environment to which such devices are normally subjected. To characterize and validate the sensor under test, the platform evaluates several parameters such as the field of view (FoV), angular resolution, sensor’s range, etc. This project results from a partnership between the University of Minho and Bosch Car Multimedia Portugal, S.A.

On the 6th September at 03:08AM local time, the Iburi-Hokkaido Earthquake, only 33 km deep triggers >5,000 co-seismic mass-movements in the hills in a 25 km radius from the epicenter. Although the majority of the mass-movements occurred in complex-geometry valley with the coalescence of deposits, a small sub-set of 59 events deposited on the semi-horizontal val-ley-floor generating separated deposits that were studied in the present contribution. The aim of the present contribution was to contribute to the existing databases of empirical relationships based on planform and vertical dataset, and to define the scalars of those relations that charac-terize the mass-movements of the Iburi-Hokkaido earthquake, with the overarching goal of generating predictors for hazard-mapping. To reach these objectives, the methodology relies on LiDAR data flown in the aftermath of the earthquake as well as aerial photographs. Using Geo-graphical Information Science (GIS) tools planform and vertical parameters were extracted to calculate the power-law relations between areas and volume, between the Fahrböschung and the volume of the deposits, as well as other geometric relationships. Results have shown that the relation S=k〖V_d〗^(2/3) where S is the surface area of a deposit and Vd the volume, and k a scalar that is function of S: k=2.1842 ln⁡(S)-10.167 with a R2 of 0.52, and this relation is improved for the open-slope mass-movements but not the valley-confined ones, that present more varia-bility. The Fahrböschung for events that started as valley-confined mass-movements was Fc = -0.043ln(D) + 0.7082 with a R2 of 0.5m while for open-slope mass-movements, the Fo = -0.046ln(D) + 0.7088 with a R2 of 0.52. These results contribute to the growing co-seismic land-slide database and they can also be the base to understand the role of the counter-slopes and complex topography on the spread and distance travelled by the mass-movement deposits.

A new method for wide-area urban roof assessment of suitability for solar photovoltaics is introduced and validated. Knowledge of roof geometry and physical features is essential for evaluation of the impact of multiple rooftop solar photovoltaic (PV) system installations on local electricity networks. This paper begins by reviewing and testing a range of existing techniques for identifying roof characteristics. It was found that no current method is capable of delivering accurate results with publicly available input data. Hence a different approach is developed, based on slope and aspect using LIDAR data, building footprint data, GIS tools and aerial photographs. It assesses each roof’s suitability for PV installation. That is, its properties should allow the installation of at least a minimum size photovoltaic system. In this way the minimum potential solar yield for region or city may be obtained. The accuracy of the new method is then established, by ground-truthing against a database of 886 household systems. This is the largest validation of a rooftop assessment method to date. The method is flexible with few prior assumptions. It is based on separate consideration of buildings and can therefore generate data for various PV scenarios and future analyses.

Archaeological topography identification from high-resolution DEMs is a current method that is used with high success in archaeological prospecting of wide areas. I present a methodology trough which burial mounds (tumuli) from LiDAR DEMS can be identified. This methodology uses geomorphometric and statistical methods to identify with high accuracy burial mound candidates. Peaks, defined as local elevation maxima are found as a first step. In the second step, local convexity watershed segments and their seeds are compared with positions of local peaks and the peaks that correspond or have in vicinity local convexity segments seeds are selected. The local convexity segments that correspond to these selected peaks are further feed to a Random Forest algorithm together with shape descriptors and descriptive statistics of geomorphometric variables in order to build a model for the classification. Multiple approaches to tune and selected the proper training dataset, settings and variables were tested. The validation of the model was performed on the full dataset where the training was performed and on an external dataset in order to test the usability of the method for other areas in a similar geomorphological and archaeological setting. The validation was performed against manually mapped and field checked burial mounds from two neighbor study areas of 100 km² each. The results show that by training the Random Forest on a dataset composed of between 75% to 100% of the segments corresponding to burial mounds and ten times more non-burial mounds segments selected using latin hypercube sampling, 93% of the burial mound segments from the external dataset are identified. There are 42 false positive cases that need to be checked, and there are two burial mound segments missed. The method shows great promise to be used for burial mound detection on wider areas by delineating a certain number of tumuli mounds for model training.

As a critical transmitter, the compact 532 nm lasers operating on high repetition and narrow pulse widths have been used widely for airborne or space-borne laser active remote sensing. We developed a free space pumped TEM₀₀ mode sub-nanosecond 532 nm laser that occupied a volume of less than 125 mm × 50 mm × 40 mm (0.25 liters). The fundamental 1064 nm laser consists of a passively Q-switched composite crystal microchip laser and an off-axis, two-pass power amplifier. The pump sources were two single-emitter semiconductor laser diodes (LD) of 808 nm with a maximum continuous wave (CW) power of 10 W each. The average power of fundamental 1064 nm laser was 1.26 W with the laser operating at 16 kHz repetition rates, and 857ps pulse widths. Since the beam distortion would be severe in microchip lasers in terms of the increase in heat load, for obtaining a high beam quality of 532 nm, the beam distortion was compensated by adjusting the distribution of pumping beam in our experiment of fundamental amplification. Furthermore, better than 0.6 W average power, 770 ps, beam quality of M² ＜1.2, and 16 kHz pulse output at 532 nm was obtained by a Type I LiB₃O₅ (LBO) crystal in the critical phase matching (CPM) regime for second harmonic generation (SHG).

The US pacific northwest recorded its highest temperature in late June 2021. The three-day stretch of scorching heat had a devastating effect on not only the residents of the state, but also on the crops thus impacting the food supply-chain. It is forecasted that streaks of 100-degree temperatures will become common. Farmers will have to adapt to the changing landscape to preserve their crop yield and profitability. A research collaborative consisting of researchers and academicians in Eastern Washington led by a pioneering startup has setup a 16.9-acre Honeycrisp Apple Smart Orchard in Grandview, WA as a laboratory to study the environmental and plant growth factors in real-time using modern computational tools and techniques like IoT (Internet of Things), Edge and Cloud Computing, and Drone and LiDAR (Light Detection and Ranging) imaging. The computational analysis is used to develop guidelines for precision agriculture for orchard blocks to address plant growth issues scientifically and in a timely fashion. The analysis also helps in creating risk-mitigation strategies for severe weather events while helping prepare farmers to maximize crop yield and profitability per acre. I was fortunate to gain access to the terabytes of farm data related to the weather, soil, water, tree, and canopy health, to analyze and formulate recommendations for the farmers that can be adopted nationwide for different crops and weather conditions. This paper discusses the different streams of farm data that were analyzed (ex. soil moisture, soil water potential, and sap flow) and the development of the framework to use data to convert insights into actionable steps. For example, the use of sensors can inform a farmer that their level of soil water potential is below threshold in a specific patch of the orchard, prompting them to turn on irrigation for the patch instead of the whole orchard. I estimate that using an IoT-sensor-based decision framework discussed in this paper, growers can save up to 55% of their water costs for the season. Using these insights, farmers can better manage their irrigation resources and labor, thus maximizing their crop yield and profits.

Automated extraction of buildings from earth observation (EO) data is important for various applications, including updating of maps, risk assessment, urban planning, policy making. Combining data from different sensors such as high-resolution multispectral (HRI) and light detection and ranging (LiDAR) has shown great potential in building extraction. Deep learning (DL) is increasingly used in multimodal data fusion and urban object extraction. However, DL-based multimodal fusion networks may underperform due to insufficient learning of “joint features” from multiple sources and oversimplified approaches to fusing multimodal features. Recently, an hybrid attention-aware fusion network (HAFNet) has been proposed for building extraction from a dataset including co-located Very-High-Resolution (VHR) optical images and Light Detection And Ranging (LiDAR) joint data. The system reported good performances thanks to the adaptivity of the attention mechanism to the features of the information content of the three streams but suffered from model overparametrization, which inevitably leads to long training times and heavy computational load. In this paper the authors propose a restructuring of the scheme, which involved replacing VGG-16-like encoders with the recently proposed EfficientNet, whose advantages counteract exactly the issues found with the HAFNet scheme. The novel configuration was tested on multiple benchmark datasets, reporting great improvements in terms of processing times, and also in terms of accuracy. The new scheme, called HAFNetE (HAFNet with EfficientNet integration), appears indeed capable of achieving good results with less parameters, translating into better computational efficiency. Based on these findings, we can conclude that, given the current advancements in single-thread schemes, the classical multi-thread HAFNet scheme could be effectively transformed by the HAFNetE scheme by replacing VGG-16 with EfficientNet blocks on each single thread. The remarkable reduction achieved in computational requirements moves the system one step closer to on-board implementation in a possible, future “urban mapping” satellite constellation.

Full waveform (FW) LiDAR holds great potential for retrieving vegetation structure parameters at a high level of detail, but this prospect is constrained by practical factors such as lack of available handy processing tools and technical intricacy of waveform processing. This study introduces a new product, named the Hyper Point Cloud (HPC) derived from FW LiDAR data, and explore its potential applications such as tree crown delineation using the HPC-based intensity and percentile height (PH) surfaces, which show a promising solution to the constraints of using FW LiDAR data. Results of the HPC present a new direction to handle FW LiDAR data and offer prospects for studying the mid-story and understory of vegetation with high point density (~ 182 points/m2). The intensity-derived digital surface model (DSM) generated from the HPC shows that the ground region has larger maximum intensity (MAXI) and mean intensity (MI) than the vegetation region while having smaller total intensity (TI) and number of intensities (NI) at the given grid cell. Our analysis of intensity distribution contours at individual tree level exhibit similar patterns, indicating that the MAXI and MI are decreasing from the tree crown center to tree boundary while a rising trend is observed for TI and NI. These intensity variable contours provide a theoretical justification for using HPC-based intensity surfaces to segment tree crowns and exploit their potential for extracting tree attributes. The HPC-based intensity surfaces and the HPC-based PH Canopy Height Models (CHM) demonstrate promising tree segmentation results comparable to the LiDAR derived CHM for estimating tree attributes such as tree locations, crown widths and tree heights. We envision that products such as the HPC and the HPC-based intensity and height surfaces introduced in this study can open new perspectives to use FW LiDAR data and alleviate the technical barrier of exploring FW LiDAR data for detailed vegetation structure characterization.

Exploring the effect of the sample size on the estimation accuracy of airborne LiDAR forest attributes in a large-scale area can help in optimizing the technical application scheme of operational ALS-based large-scale forest stand inventories. In our study, sample datasets composed of different sample plots were constructed by repeated sampling from 1003 sample plots in a subtropical study area covering 2376 × 103 km2. Sixteen multiplicative power models were built in each forest type consisting of four forest attributes. Through these models, the variations of standard deviation (SD) and coefficient of variation (CV) of R2 and rRMSE of forest attribute estimation models for different quantity levels of sample plots were also analyzed. The results showed that, first, when the sample size increased from 30 to the top limit, the SD of the forest attributes and LiDAR variables showed a decreasing trend. Second, as the sample size increased, the rRMSE of the 16 forest attribute estimation models gradually decreased, while the R2 gradually increased. Third, when the sample size was small, both the SD of R2 and rRMSE of the models were large, and the SD of R2 and rRMSE gradually decreased as the sample size increased. In 50 models conducted for each attribute at the same sample size, for the mean standard deviations of forest attributes, the ten best performing models were lower than those of the total 50 models, and the worst ten models were the opposite. When the sample size increased, the accuracy of each forest attribute estimation model for each forest type gradually improved. The variation of forest attributes and the LiDAR variable of the construction model are critical factors that affect the model’s accuracy. To efficiently apply airborne LiDAR in order to survey large-scale subtropical forest resources, the sample size of the Chinese fir forest, pine forest, eucalyptus forest, and broad-leaved forest should be 110, 80, 85, and 70, respectively.

Incident solar radiation (insolation) passing through the forest canopy to the ground surface is either absorbed or scattered. This phenomenon, known as radiation attenuation, is measured using the extinction coefficient (K). The amount of radiation at the ground surface of a given site is effectively controlled by the canopy’s surface and structure, determining its suitability for plant species.Menhinick’s and Simpson biodiversity indexes were selected as spatially explicit response variables for the regression equation using canopy structure metrics as predictors. Independent variables include modeled area solar radiation, LiDAR derived canopy height, effective leaf area index data derived from multi-spectral imagery, and canopy strata metrics derived from LiDAR point-cloud data. The results support the hypothesis that, 1.) canopy surface and strata variability may be associated with understory species diversity due to habitat partitioning and radiation attenuation, and that, 2.) such a model can predict both this relationship and biodiversity clustering.The study data yielded significant correlations between predictor and response variables and was used to produce a multiple-linear model comprising canopy relief, texture of heights, and vegetation density to predict understory plant diversity. When analyzed for spatial autocorrelation, the predicted biodiversity data exhibited non-random spatial continuity.

Super Typhoon Saola came very close to Hong Kong on 1 and 2 September 2023, necessitating the issuance of No. 10 hurricane signal, the highest tropical cyclone warning signal, in Hong Kong. While there were widespread damages in Hong Kong, no people were killed in the event with effective early warning. It is rare that a super typhoon came very close to Hong Kong and this paper is the first part in the series of the documentation of Saola to summarize the interesting observations of Saola near Hong Kong for future reference by weather forecasters, including sur-face observations, upper air observations, microburst alert from weather radars, and turbulence intensity based on spectral width measurement of radars.

Object segmentation is still considered a challenging problem in autonomous driving, particularly in consideration of real world conditions. Following this line of research, this paper approaches the problem of object segmentation using LiDAR-camera fusion and semi-supervised learning implemented in a fully-convolutional neural network. Our method is tested on real-world data acquired using our custom vehicle iseAuto shuttle. The data include all-weather scenarios, featuring night and rainy weather. In this work, it is shown that LiDAR-camera fusion with only a few annotated scenarios and semi-supervised learning, it is possible to achieve robust performance on real-world data in a multi-class object segmentation problem. The performance of our algorithm is measured in terms of intersection over union, precision, recall and area-under-the-curve average precision. Our network achieves 82% IoU in vehicle detection in day fair scenarios and 64% IoU in vehicle segmentation in night rain scenarios.

This article presents results of the polarization laser studies of the optical and microphysical characteristics of the high-level clouds (HLC). The high-altitude matrix polarization lidar (HAMPL; Tomsk, Russia) is described. HAMPL measures vertical profiles of all elements of the backscattering phase matrix (BSPM) of the HLC. Based on the joint analysis of lidar and radiosonde observations it is shown that the spatial structure of the HLC containing oriented ice crystals is inhomogeneous in the horizontal wind direction. It includes local areas with oriented particles; the sizes of such areas are estimated together with the most probable meteorological conditions of their formation. The shortcomings of the radiosonde observations performed closest to the location of the HAMPL are described. The applicability of the ERA5 reanalysis data of the European Centre for Medium-Range Weather Forecasts for use as an alternative source of information on the vertical profiles of meteorological quantities for the interpretation of HLC lidar sensing data in Western Siberia was checked.

NASA’s ICESat-2space-borne photon-counting lidar mission is providing global elevation measurements that will provide significant benefits to a variety of bio-geoscience research applications. Given the novelty of elevation and the derived data products from the ICESat-2 mission, the research community needs software tools that can facilitate photon-level analyses to support product validation and development new analysis methods. Here, we describe PhotonLabeler, a free graphic user interface (GUI) for manual labeling and visualization of ICESat-2 Geolocated Photon data (ATL03). Developed in MATLAB, the GUI facilitates the reading and display of ATL03 Hierarchical Data Format (HDF) files, the manual labeling of individual photons into target classes of choice using a number of point selections tools and enables eventual saving of labeled data in ASCII format. Other capabilities include saving and loading of labeling sessions to manage labeling tasks over time. We expect labeled data generated using the application to serve two main purposes. First, serve as ground truth for validating various products from ICESat-2 mission, especially for study sites around the world that do not have existing reference datasets such as airborne lidar. Second, serve as training and validation data in the development of new algorithms for generating various ICESat-2 data products. We demonstrate the first use case through a validation case study for the land and vegetation product (ATL08), which provides canopy and terrain height estimates, over two sites. For the first site, located in northwestern Zambia, we used ICESat-2 ATL03 data acquired at night and for our second site in Texas, US, we used ATL03 data acquired during the day. The PhotonLabeler application is freely available as a compiled MATLAB binary to enable free access and utilization by interested researchers.

In the context of the French-German space lidar mission MERLIN dedicated to the determination of the atmospheric methane content, an end-to-end mission simulator is being developed. In order to check whether the instrument design meets the performance requirements, simulations have to count all the sources of noise on the measurements like the optical energy variability induced by speckle. Speckle is due to interference as the lidar beam are quasi monochromatic. Speckle contribution to the error budget has to be estimated but also simulated. In this paper, the speckle theory is revisited and applied to MERLIN double pulsed IPDA lidar and also to the DLR demonstrator CHARM-F. Results show: on the signal path, speckle noise depends mainly on the size of the illuminating area on ground; on the solar flux, speckle is fully negligible both because the pixel size and the optical filter spectral width; on energy monitoring path a decorrelation mechanism is needed to reduce speckle noise on averaged data. Speckle noises for MERLIN and CHARM-F can be simulated by Gaussian noises with only one random draw by shot separately for energy monitoring and signal paths.

ATLID (ATmospheric LIDar) is the atmospheric backscatter LIDAR (Light Detection and Ranging) on board of the EarthCARE (Earth Cloud, Aerosol and Radiation Explorer) mission, the sixth Earth Explorer Mission of the ESA (European Space Agency) Living Planet Programme [1-5]. ATLID’s purpose is to provide vertical profiles of optically thin cloud and aerosol layers, as well as the altitude of cloud boundaries [6-10]. In order to achieve this objective ATLID emits short duration laser pulses in the UV, at a repetition rate of 51 Hz, while pointing in a near nadir direction along track of the satellite trajectory. The atmospheric backscatter signal is then collected by its 620 mm aperture telescope, filtered through the optics of the instrument focal plane assembly, in order to separate and measure the atmospheric Mie and Rayleigh scattering signals. With the completion of the full instrument assembly in 2019, ATLID has been subjected to an ambient performance test campaign, followed by a successful environmental qualification test campaign, including performance calibration and characterization in thermal vacuum conditions. In this paper the design and operational principle of ATLID is recalled and the major performance test results are presented, addressing the main key receiver and emitter characteristics. Finally, the estimated instrument, in-orbit, flight predictions are presented; these indicate compliance of the ALTID instrument performance against its specification and that it will meet its mission science objectives for the EarthCARE mission, to be launched in 2023.

Understanding swash zone dynamics is of crucial importance for coastal management as the swash motion, consisting of the uprush of the wave on the beach face and the subsequent downrush, is responsible for driving changes the beach morphology trough sediment exchanges between the sub-aerial and sub-aqueous beach. Improved understanding of the probabilistic characteristics of these motions has the potential to allow coastal engineers to develop improved sediment transport models which, in turn, can be further developed into coastal management tools. In this paper, novel descriptors of swash motions are obtained by combining field data and statistical modelling. Our results indicate that the probability distribution function (PDF) of shoreline height (p(ζ)) and trough-to-peak swash heights (p(ρ)) measured at a high energy, sandy beach were both inherently multimodal. Based on the observed multimodality of these PDFs, Gaussian Mixtures are shown to be the best method to statistically model them. Further, our results show that both offshore and surf zone dynamics are responsible for driving swash zone dynamics, which indicates unsaturated swash. The novel methods and results developed in this paper, both data collection and analysis, could aid coastal managers to develop improved swash zone models in the future.

Recent advances in open data initiatives allow us to free access to a vast amount of open LiDAR data in many cities. However, most of these open LiDAR data over cities are acquired by airborne scanning, where the points on façades are sparse or even completely missing due to the viewpoint and object occlusions in the urban environment. Integrating other sources of data, such as ground images, to complete the missing parts is an effective and practical solution. This paper presents an approach for improving open LiDAR data coverage on building façades by using point cloud generated from ground images. A coarse-to-fine strategy is proposed to fuse these two different sources of data. Firstly, the façade point cloud generated from terrestrial images is initially geolocated by matching the SFM camera positions to their GPS meta-information. Next, an improved Coherent Point Drift algorithm with normal consistency is proposed to accurately align building façades to open LiDAR data. The significance of the work resides in the use of 2D overlapping points on the outline of buildings instead of limited 3D overlap between the two point clouds and the achievement to a reliable and precise registration under possible incomplete coverage and ambiguous correspondence. Experiments show that the proposed approach can significantly improve the façades details of buildings in open LiDAR data and improving registration accuracy from up to 10 meters to less than half a meter compared to classic registration methods.

Throughout history, the unique Dacian landscape has aroused the imagination of many. For decades, researchers have been fascinated by the magnificent structures the Dacians built and how they altered the mountains to their advantage. Dacian sites, despite their grandeur, remain mostly unknown due to their position deep within Romania's vast forests, generally in remote regions and hidden from the naked eye. Ground exploration in densely forested mountain regions is extremely difficult, and even if such campaigns existed, they would be insufficient to provide a comprehensive picture of the Dacian world. The lack of high-resolution remote-sensing data for wide areas made big-scale assessments of the landscape impractical. This is about to change, as new large datasets of LiDAR-derived digital elevation models, covering the entire heart of Dacian world, are now freely available. This paper reports on one of the most recent freely available LiDAR-based high-resolution digital elevation models in Romania, its impact on Romanian mountain archaeology, and how this can shape future research directions in understanding the Dacian landscape.

Drought-induced plant mortality has increased globally during the last decades and is forecasted to influence global vegetation dynamics. Timely information on plant water dynamics is essential for understanding and anticipating drought-induced plant mortality. The most common metric that has been used for decades for measuring water stress is leaf water potential (Ψ_L), which is measured destructively. To obtain information on water dynamics from trees and forested landscapes, remote sensing methods have been developed. However, the spatial and temporal resolution of the existing methods have limited our understanding of water dynamics and diurnal variation of Ψ_L within single trees. Thus, we investigated the capability of terrestrial laser scanning (TLS) intensity in observing diurnal variation in Ψ_L during a 50 hour monitoring period and aimed to improve understanding on how large part of the diurnal variation in Ψ_L can be captured using intensity observations. We found that TLS intensity at 905 nm wavelength was able to explain 78% of the variation in Ψ_L for three trees of two tree species with a root-mean square error of 0.137 MPa. Based on our experiment with three trees, time-series of TLS intensity measurements can be used in detecting changes in Ψ_L, and thus it is worthwhile to expand the investigations to cover a wider range of tree species and forests and further increase our understanding of plant water dynamics at wider spatial and temporal scales.

This paper investigated building data from multispectral and single-photon Lidar systems. The multispectral datasets from the individual channels and fused channels were explored. The multispectral and single-photon Lidar data were compared across multiple aspects: the data acquisition geometry, number of echoes, intensity, density, resolution, data defects, noise level, and the absolute and relative accuracy. In addition, we explored the performance of the multispectral and single-photon data for roof plane detection for eight complex/stylish buildings to investigate the suitability of these data for 3D building reconstruction. The building data from the single-photon and multispectral Lidar systems were evaluated with respect to the reference building vector data with an accuracy of better than 5 cm. The advantages and disadvantages of both technologies and their applications in the urban building environment are discussed.

Monitoring crown closure evolution using multi-temporal Light Detection and Ranging (LiDAR) surveys is a method that we expect to be increasingly adopted given the availability of LiDAR sensors and the accumulating survey archives. However, little attention was devoted to comparing crown closure estimates from independent surveys. Although survey parameters cannot be modified after the data collection, we speculate that the error associated to crown closure estimates comparison can be reduced by selecting optimal post-survey parameters. In this study, we compared crown closure estimates of three airborne LiDAR surveys from 2018 (40 pt/m²) used as a reference, and two lower-density surveys from 2016 (4.5 pt/m²) and 2018 (2 pt/m²). We studied the effect of the height threshold used to separate canopy points and the grid resolution, using skewness and variance of lagged difference of crown closure. Crown closure estimates using low height thresholds were more different across surveys, resulting in higher root mean squared error (RMSE), bias and more different variograms. Results show that optimal height threshold was 3 m and grid resolution was 25 m, although there was room for decision (RMSE of 7% and 5%, and bias of 4% and 0% for 2016 and 2018 low-density surveys).

A national green planning strategy has recently been introduced in the Italian urban planning sector, aimed at making all local initiatives undertaken nationwide consistent with each other. At a regional level, Friuli Venezia-Giulia has recently implemented a Landscaping Plan, which is of an urban planning and ecological nature at an intermediate level between national and local. This article describes the local green plan of Latisana, which has been entitled Ecopolitana, given that it is represents the experimental phase, at a regional level, of the possibilities offered by landscape planning and design. Specifically, it outlines the multi-disciplinary approach used, demonstrating how landscape planning can be compared to the sustainable development of cities, with specific regard to the agricultural sector. Regarding the agricultural sector, a low-intensity cropping model is also suggested, based on the principles of agroecology and landscape ecology, which has already been implemented in the historical rural landscape of Plasencis (UD) and developed through GIS analysis and remote sensing processes. Its aim is to be the starting point for the achievement of the goals set in the 2030 Agenda, and especially Goals 13 (Climate action) and 15 (Life on land), given the current scarcity of agroecological infrastructures in the area of Latisana (UD) and the high percentage of soil used for intensive cropping.

Topography represented by high resolution digital elevation models are able to inform past and present morphological process on the terrain. High resolution LiDAR data taken by the General Directorate of Map at the surroundings of the Bergama city shows great opportunities to understand the morphological process on alluvial fan on which the city is located and the flood plain of Bakırçay river near the alluvial fan. In this paper the LiDAR data collected in 2015 have been used to create DEM’s to understand the geomorphological evolution of the alluvial fan and the flood plain around it. Since the proximal roots and medial parts of the alluvial fan have been the scene for a long human settlement most topographical traces of the morphological process have been distorted. Nevertheless, the traces of past and present morphological process at the distal fan which consist the contact zone with the flood plain are very clear on the DEM created from LiDAR data. The levees and some old courses of Bergama and Bakırçay rivers have been shown on the maps which are also important to understand the ancient roads which follows these levees.

Terrestrial laser scanning (TLS) has been adopted as a feasible technique to digitize trees and forest stands, providing accurate information on tree and forest structural attributes. However, there is limited understanding on how a variety of forest structural changes can be quantified using TLS in boreal forest conditions. In this study, we assessed the accuracy and feasibility of TLS in quantifying changes in the structure of boreal forests. We collected TLS data and field reference from 37 sample plots in 2014 (T1) and 2019 (T2). Tree stems typically have planar, vertical, and cylindrical characteristics in a point cloud, and thus we applied surface normal filtering, point cloud clustering, and RANSAC-cylinder filtering to identify these geometries and to characterize trees and forest stands at both time points. The results strengthened the existing knowledge that TLS has the capacity to characterize trees and forest stands in space and showed that TLS could characterize structural changes in time in boreal forest conditions. Root-mean-square-errors (RMSEs) in the estimates for changes in the tree attributes were 0.99-1.22 cm for diameter at breast height (Δdbh), 44.14-55.49 cm2 for basal area (Δg), and 1.91-4.85 m for tree height (Δh). In general, tree attributes were estimated more accurately for Scots pine trees, followed by Norway spruce and broadleaved trees. At the forest stand level, an RMSE of 0.60-1.13 cm was recorded for changes in basal area-weighted mean diameter (ΔDg), 0.81-2.26 m for changes in basal area-weighted mean height (ΔHg), 1.40-2.34 m2/ha for changes in mean basal area (ΔG), and 74-193 n/ha for changes in the number of trees per hectare (ΔTPH). The plot-level accuracy was higher in Scots pine-dominated sample plots than in Norway spruce-dominated and mixed-species sample plots. TLS-derived tree and forest structural attributes at time points T1 and T2 differed significantly from each other (p < 0.05). If there was an increase or decrease in dbh, g, h, height of the crown base, crown ratio, Dg, Hg, or G recorded in the field, a similar outcome was achieved by using TLS. Our results provided new information on the feasibility of TLS for the purposes of forest ecosystem growth monitoring.

Amplitude growth rates of monochromatic gravity waves were estimated and compared from multiple instrument measurements carried out in Brazil. Wave dynamic parameters were obtained from sodium density profiles from lidar observations carried out in Sao Jose dos Campos (23°S, 46°W), while all-sky images of multiple airglow layers provided amplitudes and parameters of waves over Cachoeira Paulista (23°S, 45°W). Growth rates of gravity wave amplitudes from lidar and airglow imager data were consistent with dissipative wave behavior. Only a small amount of the observed wave events presented freely propagating behavior. Part of the observed waves presented saturated amplitude. The general saturated/damped behavior is consistent with diffusive filtering processes imposing limits to amplitude growth rates of the observed gravity waves.

Recent deep learning frameworks draw a strong research interest in the application of ego-motion estimation as they demonstrate a superior result compared to geometric approaches. However, due to the lack of multimodal datasets, most of these studies primarily focused on a single sensor-based estimation. To overcome this challenge, we collect a unique multimodal dataset named LboroAV2, using multiple sensors including camera, Light Detecting And Ranging (LiDAR), ultrasound, e-compass and rotary encoder. We also propose an end-to-end deep learning architecture for fusion of RGB images and LiDAR laser scan data for odometry application. The proposed method contains a convolutional encoder, a compressed representation and a recurrent neural network. Besides feature extraction and outlier rejection, the convolutional encoder produces a compressed representation which is used to visualise the network's learning process and to pass useful sequential information. The recurrent neural network uses this compressed sequential data to learn the relation between consecutive time steps. We use the LboroAV2 and KITTI VO datasets to experiment and evaluate our results. In addition to visualising the network's learning process, our approach gives superior results compared to other similar methods. The code for the proposed architecture is released in GitHub and accessible publicly.

Multiple social and environmental justice concerns are linked to urban form such as the distribution of socioeconomic class populations, healthcare spending, air pollution exposure, and human mobility. This study used 1m resolved LIDAR data to characterize land use in Salt Lake County, Utah and associate it with sociodemographic and air quality data at the census block group and zip code levels. We found that increasing tree cover was associated with higher per capita income and lower minority populations while increasing built cover was linked to lower per capita income and higher minority populations. Air quality showed less strong correlations, however, decreased non irrigated cover, increased built cover, and higher amounts of households living under poverty was related to higher long-term PM2.5 exposure. Several policy efforts have been undertaken to improve air quality and reduce negative health outcomes in Utah which are being informed by regulatory and research grade air quality sensors.

Over a billion people around the world are disabled, among them, 253 million are visually impaired or blind, and this number is greatly increasing due to ageing, chronic diseases, poor environment, and health. Despite many proposals, the current devices and systems lack maturity and do not completely fulfill user requirements and satisfaction. Increased research activity in this field is required to encourage the development, commercialization, and widespread acceptance of low-cost and affordable assistive technologies for visual impairment and other disabilities. This paper proposes a novel approach using a LiDAR with a servo motor and an ultrasonic sensor to collect data and predict objects using deep learning for environment perception and navigation. We adopted this approach in a pair of smart glasses, called LidSonic V2.0, to enable the identification of obstacles for the visually impaired. The LidSonic system consists of an Arduino Uno edge computing device integrated into the smart glasses and a smartphone app that transmits data via Bluetooth. Arduino gathers data, operates the sensors on smart glasses, detects obstacles using simple data processing, and provides buzzer feedback to visually impaired users. The smartphone application collects data from Arduino, detects and classifies items in the spatial environment, and gives spoken feedback to the user on the detected objects. In comparison to image processing-based glasses, LidSonic uses far less processing time and energy to classify obstacles using simple LiDAR data, according to several integer measurements. We comprehensively describe the proposed system's hardware and software design, construct their prototype implementations, and test them in real-world environments. Using the open platforms, WEKA and TensorFlow, the entire LidSonic system is built with affordable off-the-shelf sensors and a microcontroller board costing less than $80. Essentially, we provide designs of an inexpensive, miniature, green device that can be built into, or mounted on, any pair of glasses or even a wheelchair to help the visually impaired. Our approach affords faster inference and decision-making using relatively low energy with smaller data sizes as well as faster communications for the edge, fog, and cloud computing.

In this article, we combine datasets from multiple research projects and remote sensing tech-nologies to evaluate the conservation conditions of La Fortaleza de Kuelap, a pre-Hispanic monument in Peru’s northeastern Andes that suffered significant damage during historically high seasonal rains in April 2022. Our analyses seek to identify the main causes of the collapse and locate places where the monument is likely at risk of further deterioration. To do so, we model surface hydrology using a digital elevation model (DEM) derived from drone LiDAR data, re-construct a history of previous collapses, and calculate the volume of the most recent by fusing terrestrial LiDAR and photogrammetric datasets. In addition, we examine subsurface water ac-cumulation through electrical resistivity data, reconstruct the stratification of the monument from seismic refraction data, and analyze vegetation loss and ground moisture accumulation using high resolution satellite imagery. Our results point to water accumulation as the most significant source of risk for La Fortaleza’s perimeter walls. Combined with adverse contemporary conser-vation interventions and natural conditions, this led to the collapse of April 2022. This integration of analytical results demonstrates how multi-scalar and multi-instrumental approaches provide comprehensive and timely assessments of conservation needs.

We consider the problem of calibrating distance measurement of Light Detection and Ranging (lidar) sensor without using additional hardware, but rather exploiting assumptions on the environment surrounding the sensor during the calibration procedure. More specifically we consider the assumption of calibrating the sensor by placing it in an environment so that its measurements lie in a 2D plane that is parallel to the ground, and so that its measurements come from fixed objects that develop orthogonally w.r.t. the ground, so that they may be considered as fixed points in an inertial reference frame. We moreover consider the intuition that moving the distance sensor within this environment implies that its measurements should be such that the relative distances and angles among the fixed points above remain the same. We thus exploit this intuition to cast the sensor calibration problem as making its measurements comply with this assumption that “fixed features shall have fixed relative distances and angles”. The resulting calibration procedure does thus not need to use additional (typically expensive) equipment, nor deploying special hardware. As for the proposed estimation strategies, from a mathematical perspective we consider models that lead to analytically solvable equations, so to enable deployment in embedded systems. Besides proposing the estimators we moreover analyse their statistical performance both in simulation and with field tests, reporting thus the dependency of the MSE performance of the calibration procedure as a function of the sensor noise levels, and observing that in field tests the approach can lead to a ten-fold improvement in the accuracy of the raw measurements.

The complexity of urban spatial configuration, which affects human-well being and landscape functioning, needs acquisition and 3d visualisation data to inform decision-making process better. One of the main challenges in sustainability research is to conceive spatial models which are capable of adapting to changes in scale and recalibrating the related indicators depending on the degree of detail and data availability. In this perspective, the inclusion of the third dimension into Urban Ecosystem Services (UES) assessment studies highlights the details of urban structure-function relationships, improves modelling and visualisation of data and impacts, aiding decision-makers to localise, assess and manage urban development strategies. The main goal of the proposed framework concerns mapping, evaluating and planning of the UES within a 3d-virtual environment to improve the visualisation of the spatial relationships among the services allocation and the urban fabric density.

The safe and reliable operation of autonomous vehicles in complex and dynamic environments is heavily dependent upon exteroceptive and proprioceptive sensors. A LiDAR system generates accurate 3D point clouds, which are crucial for the detection, classification, and tracking of multiple targets. LiDAR data, however, presents significant challenges due to its density, noise, and varying sampling rates. In this study, various clustering and MTT techniques for LiDAR point clouds will be identified and classified within the context of autonomous driving to assess the state-of-the-art methods’ key challenges and their performances. We have categorized clustering and MTT methods used in AV applications, identified research gaps and challenges and analyzed existing algorithms and their challenges in detail. Researchers and practitioners in the field of autonomous driving will find this review to be a valuable resource.

The cancelation factor (CF) is a model for the ratio between gravity wave perturbations in the airglow intensity to that in the ambient temperature. The CF model allows to estimate the momentum and energy flux of gravity waves seen in nightglow images as well as the divergence of these fluxes due to waves propagating through the mesosphere and lower thermosphere region, where the nightglow and the Na layers are located. This study uses a set of T/W Na Lidar data and zenith nightglow image observations of the OH and O(1S) emissions to test and validate the CF model from the experimental perspective. The dataset analyzed was obtained during campaigns carried out at the Andes Lidar Observatory (ALO), Chile in 2015, 2016, and 2017. The CF modeled function was compared with observed points from an empirical method for vertically propagating waves that calculates directly the ratio of the gravity wave amplitude seen in nightglow images to the wave amplitude seen in lidar temperatures. We show that the CF analytical relationship underestimates the observed results generally. However, the O(1S) emission line has better agreement respect to the theoretical value due to simpler nightglow photochemistry. In contrast, the observed CF ratio from the OH emission deviates by a factor of two from the modeled asymptotic value.

Phenotypic characterization of crop genotypes is an essential yet challenging aspect of crop management and agriculture research. Digital sensing technologies are rapidly advancing plant phenotyping and speeding-up crop breeding outcomes. However, off-the-shelf sensors might not be fully applicable and suitable for agriculture research due to diversity in crop species and specific needs during plant breeding selections. Customized sensing systems with specialized sensor hardware and software architecture provide a powerful and low-cost solution. This study designed and developed a fully integrated Raspberry Pi-based LiDAR sensor named CropBioMass (CBM), enabled by internet of things to provide a complete end-to-end pipeline. The CBM is a low-cost sensor, provides high-throughput seamless data collection in field, small data footprint, injection of data onto the remote server, and automated data processing. Phenotypic traits of crop fresh biomass, dry biomass, and plant height estimated by CBM data had high correlation with ground truth manual measurements in wheat field trial. The CBM is readily applicable for high-throughput plant phenotyping, crop monitoring, and management for precision agricultural applications.

Digital Twin Cities (DTCs) play a fundamental role in city planning and management. They allow three-dimensional modeling and simulation of cities. 3D semantic segmentation is the foundation for automatically creating enriched DTCs, as well as their updates. Past studies indicate that prior level fusion approaches demonstrate more promising precisions in 3D semantic segmentation compared to point level fusion, features level fusion, and decision level fusion families. In order to improve point cloud enriched semantic segmentation outcomes, this article proposes a new approach for 3D point cloud semantic segmentation through developing and benchmarking three prior level fusion scenarios. A reference approach based on point clouds and aerial images was proposed to compare it with the different developed scenarios. In each scenario, we inject a specific prior knowledge (geometric features,classified images ,etc) and aerial images as attributes of point clouds into the neural network’s learning pipeline. The objective is to find the one that integrates the most significant prior knowledge and enhances neural network knowledge more profoundly, which we have named the "smart fusion approach". The advanced Deep Learning algorithm "RandLaNet" was adopted to implement the different proposed scenarios and the reference approach, due to its excellent performance demonstrated in the literature. The introduction of some significant features associated with the label classes facilitated the learning process and improved the semantic segmentation results that can be achievable with the same neural network alone. Overall, our contribution provides a promising solution for addressing some challenges, in particular more accurate extraction of semantically rich objects from the urban fabric. An assessment of the semantic segmentation results obtained by the different scenarios is performed based on metrics computation and visual investigations. Finally,the smart fusion approach was derived based on the obtained qualitative and quantitative results.

Non-rigid registration presents a significant challenge in the domain of point cloud processing. The general objective is to model complex non-rigid deformations between two or more overlapping point clouds. Applications are diverse and span multiple research fields, including registration of topographic data, scene flow estimation, and dynamic shape reconstruction. To provide context, we begin with a general introduction to the topic of point cloud registration, including a categorization of methods. Next, we introduce a general mathematical formulation for point cloud registration and extend it to address non-rigid registration. A detailed discussion and categorization of existing approaches to non-rigid registration follows. We then introduce our own method where the usage of piece-wise tricubic polynomials for modeling non-rigid deformations is proposed. Our method offers several advantages over existing methods. These advantages include easy control of flexibility through a small number of intuitive tuning parameters, a closed-form optimization solution, and an efficient transformation of huge point clouds. We demonstrate our method through multiple examples that cover a broad range of applications, with a focus on remote sensing applications - namely, the registration of Airborne Laser Scanning (ALS), Mobile Laser Scanning (MLS), and Terrestrial Laser Scanning (TLS) point clouds. The implementation of our algorithms is open source and can be found on GitHub.

This study investigates the application of Light Detection and Ranging (LiDAR) sensor technology for data collection at signalized intersections characterized by a high rate of traffic crashes. The research aims to provide valuable insights into the potential of LiDAR-based data analysis to enhance road safety and traffic management at signalized intersections. The research methodology involved the deployment of LiDAR sensors at Marlboro Pike & Brooks Dr. signalized intersection in Coral Hills, Maryland. Two LiDAR sensors installed in this intersection to collect high-resolution, three-dimensional data of the intersection area from June, 1^st to July, 7^th 2023. The data included information on vehicle trajectories, speeds, and behaviors, as well as pedestrian and cyclist movement patterns. Concurrently, historical traffic crashes recorded and traffic flow data were obtained for the same intersection.The analysis of LiDAR data involved several key aspects including LiDAR data allowed for a precise evaluation of traffic flow patterns, including congestion points, traffic volume fluctuations, and peak-hour behavior. This information provided insights into potential factors contributing to crashes. By analyzing LiDAR data, the study identified near-miss incidents, which are often precursors to actual crashes. This proactive approach could assist in identifying crash-prone areas within the intersection. The LiDAR data analysis also focused on pedestrian and cyclist movements, including jaywalking and bike lane usage. The aim was to identify areas where infrastructure improvements could enhance safety for vulnerable road users. LiDAR data was compared with historical crash data to identify specific locations within the intersection that exhibited a high frequency of crashes. This information can guide targeted safety interventions. Last but not least, the study explored opportunities to optimize traffic signal timings based on real-time traffic data from LiDAR. Adaptive signal control could help mitigate congestion and reduce the risk of crashes.The results of this study demonstrated the potential of LiDAR sensor technology in collecting detailed data for traffic analysis in signalized intersections. By combining LiDAR data with historical crash records and traffic flow data, traffic engineers and urban planners can develop evidence-based strategies to reduce the frequency and severity of crashes in high-risk areas. Ultimately, this research contributes to a comprehensive understanding of how LiDAR technology can be employed to enhance road safety and traffic management, providing valuable insights for traffic engineers, urban planners, and policymakers seeking to improve the safety and efficiency of signalized intersections with a history of high traffic crashes.

Accurately quantifying the above-ground volume (AGV) and thus above-ground biomass (AGB) of forest stands is an important aspect in the conservation of mangrove ecosystem owing to their ecological and economic benefits. However, the number of studies focusing on quantifying mangrove forests’ biomass has been relatively low due to their marshy terrain, making exploratory studies challenging. In recent times, the use of LiDAR technologies in forest inventory studies has become increasingly popular, due to the reliability of LiDAR as a highly accurate means of 3D spatial data acquisition. In this study, we propose an end-to-end methodology for estimating AGV of mangrove forest stands from terrestrial LiDAR data. Many of the recent studies on this topic effectively employ machine learning algorithms such as multi layer perceptron, random forests, etc. for filtering foliage in the point cloud data of single trees. This study further extends that approach by incorporating the impact of class imbalance of forest point cloud data in a weighted random forest classifier. For the task of segmentation of wood/foliage points in a single tree point cloud, this approach yielded an average increase of 2.737% in the balanced accuracy score, 0.007 in the Cohen’s kappa score, 2.745% in the ROC AUC score and 0.857% in the F1 score. For the task of AGV estimation of a single tree, this approach resulted in an average coefficient of determination of 0.93 with respect to the ground truth volumes. For the task of counting pneumatophores in a plot-level point cloud, the proposed breadth-first searching method yielded an average coefficient of determination of 0.9391. Also, the machine learning classifier and geometric features used in this study were invariant to tree species and hence could be generalised for the classification of point clouds of other tree species as well. Finally, a breadth-first graph-search segmentation based approach is also proposed as part of this pipeline to estimate the contribution of pneumatophores to the AGB of mangrove forest stands. Since pneumatophores are a special adaptation of mangrove forests for gaseous exchange in marshy environments, this study aims to incorporate the detection and AGB estimation of pneumatophores in the inventory of mangrove forest stands. Studying the contribution of pneumatophores to the AGB of mangrove forest plots could also aid future mangrove forest inventory studies in modeling the underlying root network and estimating the below-ground biomass of mangrove trees.

Due to the energetic transition at course, new geological exploration technologies are needed to discover mineral deposits containing critical materials such as lithium (Li). The vast majority of European Li deposits are related to Li–Cs–Ta (LCT) pegmatites. Literature review indicates that conventional exploration campaigns are dominated by geochemical surveys and related exploration tools. However, other exploration techniques must be evaluated namely remote sensing (RS) and geophysics. This work presents the results of the INOVMINERAL4.0 project obtained through alternative approaches to traditional geochemistry that were gathered and integrated into a webGIS application. The specific objectives were to: (i) assess the potential of high-resolution elevation data; (ii) evaluate geophysical methods, particularly radiometry; (iii) establish a methodology for spectral data acquisition and build a spectral library; (iv) compare obtained spectra with Landsat 9 data for pegmatite identification; and (v) implement a user-friendly webGIS for data integration and visualization. Radiometric data acquisition using geophysical techniques effectively discriminated pegmatites from host rocks. The developed spectral library provided valuable insights for space-based exploration. Landsat 9 data accurately identified known LCT pegmatite targets, compared to Landsat 8. The user-friendly webGIS facilitated data integration, visualization, and sharing, supporting potential users in similar exploration approaches.

Light Detection and Ranging (LiDAR) technology, a cutting-edge advancement in mobile applications, presents a myriad of compelling use cases, including enhancing low-light photography, capturing and sharing 3D images of fascinating objects, and elevating the overall augmented reality (AR) experience. However, its widespread adoption has been hindered by the prohibitive costs and substantial power consumption associated with its implementation. To surmount these obstacles, this paper proposes a low-power, low-cost, SPAD-based system-on-chip (SoC) which packages the microlens arrays (MLA) and incorporates with a light-weight RGB-guided sparse depth imaging completion neural network for 3D LiDAR imaging. The proposed SoC integrates an 8x8 Single-Photon Avalanche Detectors (SPADs) macro pixel array with time-to-digital converters (TDC) and charge pump, fabricated using a 180nm bipolar-CMOS-DMOS (BCD) process. A random MLA-based homogenizing diffuser efficiently transforms Gaussian beams into flat-topped beams with a 45° field of view (FOV), enabling flash projection at the transmitter. To further enhance resolution and broaden application possibilities, a lightweight neural network employing RGB-guided sparse depth complementation is proposed, enabling a substantial expansion of image resolution from 8x8 to quarter video graphics array level (QVGA; 256x256). Experimental results demonstrate the effectiveness and stability of the hardware encompassing the SoC and optical system, as well as the lightweight features and accuracy of the algorithmic neural network. This integrated state-of-the-art hardware-software solution offers a promising and inspiring foundation for developing consumer-level 3D imaging applications.

Coastal resources in Lian, Batangas, have undergone significant degradation due to a combination of human activities and natural factors, including sea-level rise, changes in sea-surface temperature, fluctuations in rainfall, increased storm frequency, and sedimentation. This has led to adverse effects on key ecosystems such as corals, mangroves, and seagrasses. To assess the extent of climate change hazards on these coastal resources, a Vulnerability Assessment was conducted in the municipality of Lian, Batangas. The assessment employed a combination of the Coastal Integrity Vulnerability Assessment Toolkit (CIVAT) and Integrated Coastal Sensitivity, Exposure, and Adaptive Capacity to Climate Change (ICSEA-C) guidelines. Additionally, the analysis incorporated detailed mapping using Light Detection and Ranging (LiDAR) data for mangroves and LandSat 8 imagery for corals and seagrasses. The findings at the municipal scale revealed that a staggering 90% of mangroves in Lian, Batangas, were highly vulnerable. This vulnerability was attributed to a high score in intrinsic characteristics and a low adaptive capacity. Similarly, a majority of seagrasses in the area were classified as medium and highly vulnerable at the municipal level. Only 10–20% of seagrasses received low to medium vulnerability scores. Shockingly, almost 100% of the coral reefs in Lian, Batangas, were deemed highly vulnerable, indicating a critical threat to this crucial marine ecosystem.

This manuscript presents a system that can generate a 2D grid map and a 3D voxel model of an environment by fusing multiple sensors integrated into a robot. The fusion of these sensors is done by utilizing Robot Operating System (ROS) and some of its libraries. The sensors that are fused in the robot are a Light Detection and Ranging (LIDAR), Inertial Measurement Units (IMU), wheel encoders, and a Time-of-Flight camera. With the fusion of the point cloud data information obtained with the Time-of-Flight camera, the laser information of the LIDAR sensor, in addition to the odometry generated with the other sensors, a 2D grid map and a 3D model of two different environments were created, thus testing the performance of the system.

In this paper, we propose a system to create high-precision maps using UAV-LiDAR and to determine the location of individual fruit trees (apple trees) on the maps. The system is based on a UAV-LiDAR system that flies over an actual orchard. A UAV was flown over an actual orchard, and the point cloud of the onboard LiDAR and the location information of RTK-GNSS were obtained. The system records the LiDAR point cloud and RTK-GNSS position information. Automated software processes point cloud data offline and Automated software processes point cloud data offline and automatically segments each apple tree in the map. The RTK-GNSS position information is used for the segmented trees. The positional information obtained from RTK-GNSS was georeferenced to the segmented trees without using ground evaluation points. As a sample, location information was obtained from trees using the Quasi-Zenith Satellite System (QZSS) MICHIBIKI. The positional accuracy of the trees was evaluated using the positional information obtained from the Quasi-Zenith Satellite System MICHIBIKI as a reference. As a result, the alignment accuracy was sufficient to identify individual fruit trees.

The 21st century has seen the launch of new space-borne sensors based on LiDAR (light detection and ranging) technology developed in the second half of the 20th century. LiDAR was initially developed to integrate laser-focused imaging with the capability to determine distances through the measurement of signal return times, utilizing suitable sensors and data acquisition electronics. Nowadays, these sensors have transformed into robust instruments, offering novel opportunities for mapping terrain, canopy heights, and estimating above-ground biomass (AGB) across local to regional scales. This work aims to analyze the scientific impact of these sensors on large-scale for-est mapping to retrieve 3D canopy information, monitor forest degradation, estimate AGB, and model key ecosystem variables such as primary productivity and biodiversity. In this way, a worldwide bibliometric analysis of this topic was carried out based on up to 412 publications in-dexed in the Scopus database during the period 2004-2022. The results showed that the number of published documents increased exponentially in the last five years, coinciding with the commis-sioning of two new LiDAR space missions: Ice, Cloud and Land Elevation Satellite (ICESat-2) and Global Ecosystem Dynamics Investigation (GEDI). These missions are providing data since 2018 and 2019, respectively. The journal that demonstrated the highest productivity in this field was "Remote Sensing," and among the leading contributors, the top five countries in terms of publica-tions were the USA, China, the UK, France, and Germany. In the realm of prominent research in-stitutions, France boasted six, the USA had four, China had three, while the UK and Canada each had one. The upward trajectory in the number of publications recorded from 2004 to 2022 catego-rizes the subject under investigation as a highly trending research topic, particularly within the context of enhancing the administration of forest resources and engaging in global climate treaty frameworks mandating the surveillance and reporting of carbon stocks in forests. The recent launch in August 2022 of the Terrestrial Ecosystem Carbon Monitoring Satellite (TECMS; China State Administration of Forestry and Grassland), along with the planned launch in the coming years of up to three new space sensors, such as the Multi-footprint Observation LiDAR and Im-ager (Japan Aerospace Exploration Agency), the BIOMASS P-band Synthetic Aperture Radar (SAR) (European Space Agency), and the LiDAR Surface Topography (LIST; NASA), will greatly contribute to expanding the ability to map and monitor forest systems at very large scales. In this context, the integration of space-borne data, including imagery, SAR, and LiDAR, is anticipated to steer the trajectory of this research in the upcoming years.

This paper is a follow-up to a previous study that was conducted in a research forest and identified the optimal method for Diameter at Breast Height (DBH) estimation as a circular scanning and fitting ellipses to 4cm stem cross-sections at breast height. The aim of this study was to determine whether the identified method is applicable to natural boreal forests as well. The iPad Pro LiDAR scanner was used to acquire point clouds for 15 sites representing a range of natural boreal forest conditions in Ontario, Canada, and estimate DBH. The secondary objective was to determine if tested stand (Species composition, age, density, understory) or tree (Species, DBH) factors affected the accuracy of estimated DBH. Overall, estimated DBH values were within 1cm of actual DBH values for 78 of 133 measured trees (59%). An RMSE of 1.5cm (8.6%) was achieved. Stand age had a large effect (&gt;0.15) on the accuracy of estimated DBH values, while density, understory, and DBH had moderate effects (0.05-0.14). No trend was identified between accuracy and stand age. Accuracy improved as understory density decreased and as tree DBH increased. Inertial Measurement Unit (IMU) and positional accuracy errors with the iPad Pro scanner limit the feasibility of using this device for forest inventories.

The climate change impacts on some regions of the planet faster and stronger. These areas are known as the hot spots for climate change and Cyprus (Nicosia) in the Mediterranean is one of these spots. This paper aims to analyze the significant changes of atmospheric aerosol characteristics in 2019 and during the extreme event of 25 April 2019. We study the aerosol optical thickness (AOT), Ångström exponent, single scattering albedo, refractive index (imaginary and real parts), size, and vertical distribution of aerosol particles during the event of a high atmospheric aerosol contamination over Nicosia in details. For this purpose, we used the ground-based lidar, observations of the sun-photometer AERONET Nicosia station, satellite products from the Moderate Resolution Imaging Spectroradiometer (MODIS), and back trajectories of air movements calculated using the Hybrid Single Particle Lagrangian Integrated Trajectory Model (HYSPLIT). On 23–25 April, according to lidar and sun-photometer observations, strong aerosol pollution over Nicosia was detected. On April 25, 2019, the AOT value exceeds 1.0 at λ = 440 nm. Analysis of the optical and microphysical characteristics supported that the pollution consists of mainly Saharan dust and partly urban aerosols. This assumption was confirmed by HYSPLIT backward trajectories and MODIS images where air masses containing dust particles came from North Africa and from the Eastern part of Europe.

We discuss a remote sensing system that is used to simultaneously detect range-resolved differential absorption LIDAR (light detection and ranging; DIAL) signals and integrated path DIAL signals (IP-DIAL) from aerosol targets for ranges up to 22 km. The DIAL/IP-DIAL frequency converter consists of an OPO pumped at 1064 nm to produce light at 1.6 μm and operates at 100 Hz pulse repetition frequency. The probe light is free space coupled to a movable platform that contains one transmitter and two receiver telescopes. Hybrid photon counting/current systems increase the dynamic range for detection by two orders of magnitude. Range resolved and column integrated dry-air CO2 and CH4 mixing ratios are obtained from line shape fits of CO2 and CH4 centered at 1602.2 nm and 1645.5 nm, respectively and measured at 10 different frequencies over ≈ 1.5 cm-1 bandwidth. The signal-to-noise ratios (SNR) of the IP-DIAL returns from cloud aerosols approach 1000:1 and the uncertainties in the mixing ratios weighted according to the integrated counts over the cloud segments range from 0.1 % to 1 %. The range averaged DIAL mixing ratios are in good agreement with the IP-DIAL mixing ratios at the 1 % to 2 % level for both CO2 and CH4. These results can serve as a validation method for future active and passive satellite observational systems.

3D object detection is crucial for autonomous driving to understand the driving environment. Since the pooling operation causes information loss in the standard CNN, we have designed a wavelet multiresolution analysis-based 3D object detection network without a pooling operation. Additionally, instead of using a single filter like the standard convolution, we use the lower-frequency and higher-frequency coefficients as a filter. These filters capture more relevant parts than a single filter, enlarging the receptive field. The model comprises a discrete wavelet transform (DWT) and an inverse wavelet transform (IWT) with skip connections to encourage feature reuse for contrasting and expanding layers. The IWT enriches the feature representation by fully recovering the lost details during the downsampling operation. Element-wise summation is used for the skip connections to decrease the computational burden. We train the model for the Haar and Daubechies (Db4) wavelets. The two-level wavelet decomposition result shows that we can build a lightweight model without losing significant performance. The experimental results on the KITTI’s BEV and 3D evaluation benchmark show our model outperforms the Pointpillars base model by up to 14 \% while reducing the number of trainable parameters. Code will be released.

The task of determining the distance from one object to another is one of the important tasks solved in robotics systems. Conventional algorithms rely on an iterative process of predicting distance estimates, which results in an increased computational burden. Algorithms used in robotic systems should require minimal time costs, as well as be resistant to the presence of noise. To solve these problems, the paper proposes an algorithm for Kalman combination filtering with a Goldschmidt divisor and a median filter. Software simulation showed an increase in the accuracy of predicting the estimate of the developed algorithm in comparison with the traditional filtering algorithm, as well as an increase in the speed of the algorithm. The results obtained can be effectively applied in various computer vision systems.

Gardens play a key role in the definition of the cultural landscape since they reflect the culture, identity and history of a people. They also contribute to the ecological balance of the city. Despite gardens have an historic and social value, they are not protected as much as the rest of the existing heritage, like architecture and archaeological sites. While methods of built-heritage mapping and monitoring are increasing and constantly improving to reduce built-heritage loss and the severe impact of natural disasters, the documentation and survey techniques for gardens are often antiquated, inventories are typically made by non-updated/updatable reports, and rarely they are on digital format and in 3D. This paper presents the preliminary results of a study on latest technology for gardens laser scanning. We compared static Terrestrial Laser Scanning and Mobile Laser Scanning point clouds, to evaluate their quality for documentation and the estimation of the tree attributes. The evaluation is based on visual observation and graphic comparison of the two point clouds acquired in different instances. Both methods produced useful outcomes for the research scope within their limitations. Terrestrial Laser Scanning is still the method that offers more accurate point clouds with a higher point density and less noise level. However, the more recent Mobile Laser Scanning is able to survey in less time, significantly reducing the costs for site activities, data post-production and registration. Both methods have their own restrictions that are amplified by site features, mainly the lack of plans for the geometric alignment of scans and for the Simultaneous Location and Mapping (SLAM) process. We also offer the results of a comparison of the functional range of the two machines, as well as for a comparison of their terrain information extraction capabilities.

This research is focused on two key areas. The first is mapping the 2022 flood in the Red River of the North near Grafton, North Dakota, US, and the second is evaluating the scour potential of the Grafton Bridge. Local scour of bridge piers can cause hydraulic structures such as bridge piers and abutments to fail during floods, making it a crucial area of investigation. To collect bathymetry and discharge data during low and high flow conditions, including a flood event with a 16.5-year return period in 2022, an Autonomous Surface Vehicle (ASV) incorporated with LiDAR DEM (Digital Elevation Model) data obtained from the US Geological Survey (USGS) National Map was used. Flood mapping and evaluation of local scour around the bridge pier were conducted using the HEC-RAS 6.0.0 software, which utilizes the Colorado State University method as a default equation. This research demonstrates the potential of ASVs in collecting critical data and LiDAR DEM data is an efficient method for flood mapping and determining scour potential, as it integrates bathymetry, flow velocity, and flood prediction.

Recently, new semantic segmentation and object detection methods have been proposed for direct processing of three-dimensional (3D) LiDAR sensor point clouds. LiDAR can produce highly accurate and detailed 3D maps of natural and man-made environments and is used for sensing in many contexts due to its ability to capture more information and its robustness to dynamic changes in the environment. In addition, the cost of LiDAR sensors has decreased in recent years, which is an important factor for many application scenarios. The challenge with 3D LiDAR sensors like the Velodyne HDL-64E S2 is that they can output large 3D data at up to 1,300,000 points per second, which is difficult to process in real time when applying complex algorithms and models for efficient semantic segmentation. Most existing approaches are either only suitable for relatively small point clouds or rely on computationally intensive sampling techniques to reduce their size. As a result, most of these methods do not work in real-time in realistic field robotics application scenarios, making them unsuitable for practical applications. Systematic point selection is a possible solution to reduce the amount of data to be processed, but although it is memory and computationally efficient, it selects only a small subset of points, which may result in important features being missed. To address this problem, we propose a new approach to semantic segmentation in forestry that uses a systematic sampling method in which the local neighbors of each point are retained to preserve geometric details. Our approach has been shown to process up to 1 million points in a single pass. It outperforms the state of the art in efficient semantic segmentation in large datasets such as Semantic3D. We also present a preliminary study on the performance of LiDAR-only data, i.e., intensity values from LiDAR sensors without RGB values for semi-autonomous robot perception.

Simultaneous Localization and Mapping (SLAM) is considered as a challenge in environments with many moving objects. This paper proposes a novel LiDAR Inertial Odometry framework, ID-LIO, for dynamic scenes that builds on LIO-SAM. To detect the pointclouds on the moving objects, a dynamic point detection method is integrated, which is based on pseudo occupancy along the spatial dimension. Then, we present a dynamic points propagation and removal algorithm based on indexed points to remove more dynamic points in the local map along the temporal dimension and update the status of the point features in keyframes. In the LiDAR odometry module, a delay removal strategy is proposed for history keyframes and the sliding window-based optimization includes the LIDAR measurement with dynamic weights to reduce error from dynamic points in keyframes. We perform the experiments both on the public low dynamic and highly dynamic data set. The results show that the proposed method greatly increases the localization accuracy in high dynamic environments. And the ATE(Absolute Trajectory Error) average RMSE((Root Mean Square Error) of our ID-LIO can be improved by 67% and 85% in the UrbanLoco-CAMarketStreet dataset and UrbanNav-HK-Medium-Urban-1 dataset respectively when compared with LIO-SAM.