Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

Li-rich layered oxide cathode materials have become one of the most promising cathode materials for high-energy-density lithium-ion batteries owning to its high theoretical specific capacity, low cost, high operating voltage and environmental friendliness. Yet they suffer from severe capacity and voltage attenuation during prolong cycling, which blocks their commercial application. To clarify these causes, we synthesize 0.5Li2MnO3·0.5LiNi0.8Co0.1Mn0.1O2 (LL-811) with high-nickel-content cathode material by a solid-sate complexation method, and it manifests a lot slower capacity and voltage attenuation during prolong cycling compared to LL-111 and LL-523 cathode materials. The capacity retention at 1C after 100 cycles reaches to 87.5% and the voltage attenuation after 100 cycles is only 0.460 V. Combining X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscopy (TEM), it indicates that increasing the nickel content not only stabilizes the structure but also alleviates the attenuation of capacity and voltage. Therefore, it provides a new idea for designing of Li-rich layered oxide cathode materials that suppress voltage and capacity attenuation.

Lithium-rich layered oxides is one of the most perspective candidates for cathode materials of lithium ion battery, because of its high discharge capacity. However, there are some disadvantages of uneven composition, voltage decay, and poor rate capacity, which are closely related to the preparation method. Here, 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 were successfully prepared by sol-gel and oxalate co-precipitation methods. A systematic analysis of the materials shows that the 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 prepared by the oxalic acid co-precipitation method has the most stable layered structure and the best electrochemical performance. The initial discharge specific capacity is 261.6 mAh·g-1 at 0.05 C, and the discharge specific capacity is 138 mAh·g-1 at 5 C. The voltage decay is only 210 mV, and the capacity retention is 94.2% after 100 cycles at 1 C. The suppression of voltage decay can be attributed to the high nickel content and uniform element distribution. In addition, tightly packed porous spheres help to reduce lithium ion diffusion energy and improve the stability of the layered structure, thereby improving cycle stability and rate capacity. This conclusion provides a reference for designing high energy density lithium-ion batteries.

Platelet and fibrin-rich orthobiologic products, such as autologous platelet concentrates, have been extensively studied and appreciated for their beneficial effects in multiple conditions. PRP and its derivatives, including PRF, have demonstrated encouraging outcomes in clinical and laboratory settings, particularly in the treatment of musculoskeletal disorders such as OA. Although PRP and PRF have distinct characteristics, they share similar properties. The relative abundance of platelets, peripheral blood cells and molecular components in these orthobiologic products stimulate numerous biological pathways. These include inflammatory modulation, augmented neovascularization, and delivery of pro-anabolic stimuli that regulate cell recruitment, proliferation, and differentiation. Furthermore, the fibrinolytic system, which is sometimes overlooked, plays a crucial role in musculoskeletal regenerative medicine by regulating proteolytic activity and promoting the recruitment of inflammatory cells and MSCs in areas of tissue regeneration, such as bone, cartilage, and muscle. PRP acts as a potent signaling agent; however, it diffuses easily, while the fibrin from PRF offers a durable scaffolding effect that promotes cell activity. The combination of fibrin with hyaluronic acid, another well-studied orthobiologic product, has been shown to improve its scaffolding properties, leading to more robust fibrin polymerization. This supports cell survival, attachment, migration, and proliferation. Therefore, the administration of the "power mix" containing HA and autologous PRP + PRF may prove to be a safe and cost-effective approach in regenerative medicine.

To address the limitations of the current anodes of Li+-ion batteries (LIBs), a Ge/GeO2/Carbon (Ge@GeO2-C) composite was designed by introducing a high-energy ball-milling process for advanced LIBs. Ge@GeO2-C is prepared and characterized by XPS, XRD, SEM, and TEM, which facilitate synthesis and provide controllability with respect to milling time. Interestingly, as the ball-milling time increased, the proportion of metallic Ge increased during the carbon thermal reduction reaction. The electrochemical characteristics of Ge@GeO2-C are assessed using differential capacity analysis (dQ/dV) and galvanostatic charge-discharge techniques to confirm its viability as an anode material in LIBs. The results demonstrated decent initial and secondary capacities of approximately 1800 mAh g-1 (for the first cycle) and 838 mAh g-1 (for the second cycle) at a rate of C/60 by the reaction between Ge and the Li-Ge complex. Furthermore, postmortem characterization was performed to gain an understanding of the material, suggesting future prospects for advanced LIBs.

In this paper, a new anode environmentally friendly for hydrogen production was developed based on 430 stainless steel with an electrodeposited cobalt layer. The novelty of this work is the cobalt source once the electrodeposition bath was obtained from recycling of spent Li-ion batteries cathode with composition LiCoO₂. The electrodeposited cobalt behaves as supercapacitor in KOH 1M. In the linear voltammetry in KOH 1M, when the overpotential reaches 370 mV, the anodic density current for 430 SS/Co is 19 mA cm⁻². Thus, the anode developed in this paper achieves the double of density current with half of production cost if compared with 316SS. Moreover the anode construction described in this paper is an excellent option for Li- ion battery recycling.

In this paper the application of recycled Li-ion batteries spent cathode (LIB-SC) combined with NaHCO₃/H₂O₂ system is presented for the first time in the literature as an alternative for degradation of potentially toxic organic molecules. The model pollutant choice was methylene blue molecule. The spent cathode composition corresponds to LiCoO₂, which was proved by the XRD and EDX. Regarding the decolorization of methylene blue solution, the addition of NaHCO₃ in comparison with only H₂O₂ reduces the complete decolorization time in 96%. This reduction occurs because the radical CO₃ is more stable than OH. In this way, the application the system proposed in this article is aimed at solving two major global problems: the disposal of cell phone batteries and the pollution of liquid effluents.

Anode materials based on TiO2 nanoparticles of different morphologies were prepared using the hydrothermal method and characterized by various techniques, such as X-ray diffraction (DRX), scanning electron microscopy (FE-SEM), and N2 absorption. The TiO2 nanoparticles prepared were used as anode materials for lithium-ion batteries (LIBs), and their electrochemical properties were tested using discharging/charging measurements. The results showed that the initial morphology of the nanoparticles plays a minor role in battery performance after the first few cycles and that better capacity was achieved for TiO2 nanobelt morphology. The sharp drop in the specific capacity of LIB during their first cycles is examined considering changes in the morphology of TiO2 particles and their porosity properties in terms of shape and connectivity.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

The increased interest in space activities, structural health monitoring, and terrestrial monitoring in hostile and inaccessible zones places a high demand for energy sources for autonomous systems. Conventional electrochemical batteries that could be used are plagued by low energy storage density, short life, disposal of unwanted batteries, and related undesired recharging or replacement maintenance requirements, which endangers the environment. Fuel cells and solar energy sources being exploited to mitigate the adverse effect of environmental threats posed by batteries and fossil fuels are costly to acquire and maintain. The availability of energy sources derived from waste heat from radioactive decay for domestic appliances and industrial equipment will also help alleviate the effects of climate change, which continues to threaten the environment due to fossil fuel energy-based sources that emit harmful carbon monoxide into the atmosphere. A combination of energy from waste heat, harvested via thermoelectricity and existing battery technology to produce a hybrid energy source, can guarantee secured energy for an extended period. Based on the Seebeck effect, thermoelectric energy generation may considerably contribute to sustainable energy development and meet the power demand for spacecraft applications. Modeling of the energy from waste heat, the Li-ion battery, and a hybrid energy source are considered, and their performances are established using the MATLAB/Simulink environment. Results confirmed the comparative advantage of the hybrid energy source over and above the respective electrochemical batteries and waste heat energy sources regarding effectiveness and performance efficiency. Since batteries are required to operate in a constantly changing environment, the effects of temperatures on batteries were investigated. The results show that the performances of batteries decrease with a decrease in ambient temperature and that the higher the maximum operating capacity, the higher the battery's internal temperature.

This code provides computational facilities to simulate current versus time during the charging of Li-ion cells at desire constant voltage by considering multiscale physical phenomena. This code only considers a powder of active materials (at microscale or nanoscale) and a small part of electrolyte around it as a half cell. Then it is extended to a complete cell by applying correct boundary conditions. This code is very useful by modifying code parameters to understand the effect of the complex shape of active materials powder (surface area and powder size), kind of electrolyte, and the applied voltages on the charging response of Li-ion cell. As a summary, a microscale approach to the design of Li-ion cells has been provided via this code.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Pterygium is a common ocular disease caused by abnormal cellular proliferation leading to abnormal fibrovascular growth of the conjunctiva. The main treatment is surgical removal; however, despite the improvement of surgical techniques and development of adjuvant therapies, postoperative recurrence, which can be as high as 89%, remains a challenge. Currently, pterygium excision with conjunctival autograft remains the preferred surgical technique to decrease recurrence, especially when combined with ciclosporin eye drops. Nevertheless, there is no gold standard surgical technique to prevent pterygium recurrence. Therefore, this review aims to assess the safety, effectiveness and, applicability of platelet-rich fibrin membrane for primary pterygium surgery and assess its possible benefits in resource-limited settings.

In order to develop waterborne silicate anticorrosive coatings to replace solvent-based anticorrosive coatings used widely in ship’s industry, epoxy modified silicate emulsions were synthesized with different content of epoxy resin, then aqueous silicate zinc-rich coatings were prepared with synthesized silicate emulsion, triethylamine and zinc powder. The influence of the content of epoxy on the properties and chemical structure of modified emulsion, mechanical properties of silicate coatings, and the corrosion behavior of silicate zinc-rich coatings in 3.5% NaCl solution were investigated. The coating samples on steel were measured by immersion test, Tafel polarization test and electrochemical impedance spectroscopy (EIS) test with different immersion time. The results showed that epoxy modified silicate emulsions were successfully synthesized. With the increase of epoxy content, the viscosity and the solid content of modified emulsion increases, the impact resistance of the silicate coating raises, the pencil hardness decreases, but the adhesion is not affected. Epoxy modification can reduce to s certain extent the corrosion driving force of zinc rich coating and increase the impedance of the zinc-rich coating decreases with the increase of immersion time in 3.5% NaCl solution. With the increase of the epoxy content, the resistance value of the zinc-rich coating increases, indicating the ability of the coating to resist corrosive media is enhanced.

Electric Vehicles (EVs) are the need of the hour due to growing climate change problems linked with the transportation sector. Battery Thermal Management System (BTMS), which is accountable for certifying safety and performance of lithium-ion batteries (LiB), is the most vital part of an EV. LiB has auspicious gravimetric energy density but the heat generation due to chemical reactions inside a LiB during charging and discharging causes temperature rise which has a direct effect on LiB performance and safety. This study specifically focuses on aircooled BTMS, defines different types of air-cooled BTMS (active and Passive), discusses limitations associated with air-cooled BTMS, and investigates different optimization techniques and parameters to improve performance of air-cooled BTMS. Maintaining temperature within optimum range and uniform temperature distribution between cells of a battery pack are the major design parameters for improving the performance and efficiency of air-cooled BTMS. Various optimization techniques including cell arrangement with a battery pack, air-flow channel optimization, and air inlet/outlet position variations are discussed and each technique is thoroughly reviewed. Finally, it’s noted that passive air-cooled BTMS is not that effective for long-distance vehicles so most researchers shifted their focus toward active air-cooled BTMS. Active air-cooled BTMS requires a lot of power for effective performance. Lastly, the most recent field of air-cooled BTMS technology which is Air-Hybrid BTMS is discussed and declared a very promising solution for overcoming major limitations associated with air-cooled BTMS.

This work aimed to synthesize new N-rich triazole compounds. In this article we describe the synthesis of three different 1,2,4-triazole-based systems starting from 1,3-diaminoguanidine hydrochloride monohydrate. The structure of the obtained crystals was established by single-crystal X-Ray diffraction. The high nitrogen content of the synthetized compounds makes them building blocks for the application in the High-Energy-Density material science.

Peri-implant diseases are defined as pathological inflammatory reactions in the tissue surrounding the osseointegrated implants. They are classified into two categories: mucositis - defined as peri-implant soft tissue inflammation and peri-implantitis - bone loss in the peri-implant region. A clinical case of a 61-years-old woman with an implant in the 46 anatomical position and a 5-year follow-up is presented. A probe depth of 5mm and a bone defect length of 35% was observed. The Implacure® Protocol was applied, with the main objective of eliminating the biofilm present on the exposed implant surface. There are multiple approaches to treat peri-implant diseases. While non-surgical treatment is essential for mucositis control, the treatment of peri-implantitis surgical treatment should be considered. Regenerative bone reconstruction promotes bone repair in the defect area and reduces bleeding during probing. To achieve that, autologous fibrin combined with Cerasorb M® was used. The proposed approach in the exposed clinical case involves the application of Implacure® Protocol, whose combination of the physical decontamination technique, together with the use of chlorhexidine and orthophosphoric acid, added with the combination Piperacillin + Tazobactam together with hyaluronic acid, provide a base that allows to regenerate bone using platelet-rich fibrin with Cerasorb M® and increase the survival time of the implant.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

The paper concludes that the choice of charging strategy depends on the specific requirements and limitations of the off-grid solar PV system, and that a careful analysis of the factors that affect performance is necessary to identify the most appropriate approach. Also provides valuable insights for designing and optimizing off-grid solar PV systems, which can help to improve the efficiency, reliability, and cost-effectiveness of these systems.

Electric vehicles (EVs) are being endorsed as the uppermost successor to fuel-powered cars, with timetables for banning the sale of petrol-fueled vehicles announced in many countries. However, the range and charging times of EVs are still considerable concerns. Fast charging could be a solution to consumers' range anxiety and the acceptance of EVs. Nevertheless, it is a complicated and systematized challenge to realize the fast charging of EVs because it includes the coordinated development of battery cells, including electrode materials, EV battery power systems, charging piles, electric grids, etc. This paper aims to serve as an analysis for the development of fast-charging technology, with a discussion of the current situation, constraints and development direction of EV fast-charging technologies from the macroscale and microscale perspectives of fast-charging challenges. It is emphasized that to essentially solve the problem of fast charging, the development of new battery materials, especially anode materials with improved lithium ion diffusion coefficients, is the key. It is highlighted that red phosphorus is the most promising anode that can simultaneously satisfy the double standards of high-energy density and fast-charging performance to a maximum degree.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

Garnet-type Ta-doped Li7La3Zr2O12 (LLZO) ceramic solid electrolytes with Ga2O3 additive were synthesized via a conventional solid-state reaction process. When the amounts of Ga2O3 additive were below 2 mol %, the sintered sample has a dense structure composed of grains with the averaged size of 5 to 10 μm, while 3 mol % or more Ga2O3 addition causes the significant increase in grain size above several 10 to 100 μm, due to the sintering with large amount of liquid Li-Ga-O phase at high temperature. The highest total (bulk + grain-boundary) ionic conductivity of 1.1 mS cm1 at room temperature was obtained in the sample with 5 mol % Ga2O3 addition. However, in galvanostatic testing of the symmetric cell with Li metal electrodes, this sample was shorted by Li dendrite growth into solid electrolyte at current density below 0.2 mA cm2. The tolerance for Li dendrite growth is maximized in sample sintered with 2 mol % Ga2O3 addition, which was shorted at 0.8 mA cm2 in the symmetric cell. Since the interfacial resistance between Li metal and solid electrolyte was nearly identical among the all samples, the difference in tolerance for Li dendrite growth is mainly attributed to the difference in microstructure of sintered samples depending on the amounts of Ga2O3.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

The employment of PRP in regenerative medicine has not generated the promised grandiose outcomes. Nonetheless, it currently remains the gold standard strategy for tissue regeneration. Therefore, scientific research has focused on identifying other matrices rich in growth factors and cytokines to improve the efficacy of PRP. In the present study, a new technology called AMPLEX PLUS -compound derived from colostrum enriched with exosomes- was applied in combination with PRP to evaluate the concentration trend of 20 bioactive molecules. The results show that the concentration of all the compounds analyzed increased significantly in PRP samples with AMPLEX PLUS technology compared with samples containing only plasma or PRP, suggesting how this new strategy could improve the performance of PRP and make significant advances in regenerative medicine.

Transportation is the primary consumer of oil, accounting for a significant portion of global energy consumption (34%) and CO2 emissions (40%). Electrifying road transportation is crucial to mitigate the effects of global warming. The abundant potential of renewable energy sources like solar and wind is hindered by their intermittent nature and incongruity with peak energy demands. This calls for the development of sophisticated energy storage solutions. Metal-air batteries (MABs), emerging as viable alternatives to lithium-ion batteries (LIBs), have attracted considerable attention due to their promising applications in the transportation sector. Despite substantial progress in MAB development over the past two decades, overcoming critical challenges such as electrolyte decomposition, carbon cathode degradation, anodic dendrite growth, and air impurities remains essential for their commercial viability. This mini-review provides a comprehensive overview of MAB fundamentals and the challenges associated with their development. The insights presented in this review serve to illuminate the current landscape and future prospects of MABs in the transportation sector.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

This paper focuses on the comparative analysis of lithium-ion batteries (LIB) thermal management with aim to maintain working temperature in the range 15 ℃ – 35 ℃. This is to prevent thermal runaway and high temperature gradients. The proposed approach is to employ the biodiesel, situated inside the diesel/LIB powered hybrid electric vehicle, to supply as fuel and coolant. A 3S2P LIB module is simulated using Ansys-Fluent CFD software tool. The system without a coolant shows that LIB has exceeded the optimum maximum temperature, which leads to shortened life-cycle and poor performance. Four fatty acid methyl ester biodiesels are used as coolants, namely palm, karanja, jatropha, and mahua oils. When compared with conventional methods of cooling, using air and 3M Novec liquid, the palm biodiesel coolant proves to be the best option to maintain LIB temperature within the optimum working range. With the use of palm biodiesel, the system is estimated to lightweight the BTMS by 43%, compared to the case when 3M Novec is used to maintain the same temperature range.

Bulk composition, mineralogy and microchemistry of various fractions of the filling of the Crater No. 4 at Emmerting were investigated. Here we present mainly the fine fractions, which, in contrast to pebbles larger than ca. 4 cm, are relatively poor in material affected by melting. A 0.1 mm long meteorite fragment without ablation features was found, and remelted fragments of the same body have been identified. The projectile was dominated by enstatite, also containing forsterite, basic plagioclase, Ni-rich pyrrhotite and troilite, kamacite, silica, and probably merrillite. The molten fragments contain porous Mg-rich glass (indicating temperature > 1500 °C), minor Fe oxides, and occasionally uncommon Ni-rich minerals. The bulk composition and electron microprobe show that the amount of meteoritic material is low (<< 1 %), and it is not unequivocally manifested even in platinum-group elements abundances and osmium isotope ratios (the latter, however, were only measured in two samples). This can be explained by dilution of the filling by particles brought after the crater formation, and by probably achondritic composition of the projectile. Relatively large hollow spheroid Fe oxide particles were observed in thin sections from the magnetic fraction. A Mn oxide hollow spherule has also been found. In magnetically separated filling from the nearby Crater No. 5, bulk chemical composition points to contamination with several metals and metalloids probably due to influence of recent alluvial sediments. Therefore, the extent of meteoritic contamination in this crater may be even smaller.

Musculoskeletal disorders are increasingly prevalent worldwide, causing significant socioeconomic burdens and diminished quality of life. Notably, patellar chondropathy (PC) is among the most widespread conditions affecting the joint structures, resulting in profound pain and disability. Hyaluronic acid (HA) and platelet-rich plasma (PRP) have emerged as reliable, effective, and minimally invasive alternatives. Continuous research spanning from laboratory settings to clinical applications demonstrate the numerous advantages of both products. These encompass lubrication, anti-inflammation, and stimulation of cellular behaviors linked to proliferation, differentiation, migration, and the release of essential growth factors. Cumulatively, these benefits support the rejuvenation of bone and cartilaginous tissues, which are otherwise compromised due to the prevailing degenerative and inflammatory responses characteristic of tissue damage. While existing literature delves into the physical, mechanical, and biological facets of these products, as well as their commercial variants and distinct clinical uses, there is limited discussion on their interconnected roles. We explore basic science concepts, product variations, and clinical strategies. This comprehensive examination provides physicians with an alternative insight into the pathophysiology of PC as well as biological mechanisms stimulated by both HA and PRP that contribute to tissue restoration.

An 11-month-old castrated male Pomeranian presented with nonunion following a femoral fracture that occurred after femoral head and neck osteotomy. Radiography and computed tomography revealed severe atrophy of the proximal bone fragment and retardation of the ipsilateral distal fragment and tibia. An autogenous bone graft using coccygeal bone was performed, in which three-and-a-half coccyges were placed in series and fixed using an orthogonal locking plate. To promote bone healing and facilitate proper weight bearing and ambulation, bone morphogenetic proteins, biphasic calcium phosphate, platelet-rich plasma, passive range of motion exercises, transcutaneous electrical nerve stimulation, neuromuscular electrical stimulation, and low level laser therapy were applied. During the four-year follow-up, it was observed that the previously engrafted bone healed well and maintained stability over a prolonged period, resulting in the patient being able to walk and trot comfortably with good outcomes. However, some degree of lameness was noted during galloping owing to limb shortening and joint contracture.

To alleviate the contradiction between the increasing demand for water and the shortage of resources and to provide a favorable institutional environment for water rights trading, the Chinese government has strengthened the top-level design of water management system. However, the water-rich regions (southern regions of China) have good water resource endowment and a surplus of total water consumption indicators. Does this mean that there is no incentive and no need to conduct water rights trading in these regions? Through the investigation of water rights circulation cases in the Taihu Basin, a typical water-rich region of China, we established the existence of trading demand and some difficulties in conducting transactions. This paper argues that the needs of trading include alleviating the water gap in regional development, solving the water demand for large new projects, coordinating trans-jurisdiction water disputes. The plight of trading includes the lack of awareness, irregular process, excessive administrative intervention, and imperfect trading system.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Mutations of PKD1 coding for polycystin-1 (PC1) account for most of the autosomal dominant polycystic kidney disease (ADPKD). The extracellular region of PC1 contains many evolutionarily conserved domains for ligand interactions. Among these is the leucine-rich repeats (LRR) in the far N-terminus of PC1. Using zebrafish (Danio rerio) as an in vivo model system, we explored the role of LRR in the function of PC1. Zebrafish expresses two human PKD1 paralogs, pkd1a and pkd1b. Knockdown of both genes in zebrafish by morpholino antisense oligonucleotides produced phenotypes of dorsal axis curvature and pronephric cyst formation. We found that overexpression of LRR suppressed both phenotypes in pkd1-morphant zebrafish. Purified recombinant LRR domain inhibited proliferation of HEK cells in culture and interacted with the heterotrimeric basement membrane protein laminin-511 (α5β1γ1) in vitro. Mutations of amino acid residues in LRR structurally predicted to bind laminin-511 disrupted LRR-laminin interaction in vitro and neutralized the ability of LRR to inhibit cell proliferation and cystogenesis. Our data support the hypothesis that the extracellular region of PC1 plays a role in modulating PC1 interaction with the extracellular matrix and contributes to cystogenesis of PC1-deficiency.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

Organic-rich shale deposits of the Paleocene-Eocene Palana Formation in western Rajasthan, India were systematically analyzed based on the elemental composition and organic geochemistry combined with microscopic examinations to evaluate the sedimentary paleoenvironmental conations and volcanic activity and their impact on the high organic carbon accumulation. The Palana shales are categorized by high OM and sulfur contents with total values up to 36.23 wt. % and 2.24 wt. %, respectively, suggesting marine setting and anoxic environmental conditions during the Paleocene-Eocene period. The richness of phytoplankton algae (i.e., telalginite and lamalginite) together with redox-sensitive trace elements further suggests anoxic environmental conditions. The significant low oxygen conditions may contributes to enhance preservation of organic matter during deposition. The mineralogical and inorganic geochemical indicators demonstrate that the Palana organic-rich shale facies was accumulated in warm and humid climate and low salinity stratification conditions of the water columns, thereby contributing to high bioproductivity of the phytoplankton algae blooms within the photic zone. The presence of the high concentrations of Fe-rich silica minerals such as olivine in most of the Palana organic-rich shales facility volcanic origin and supports hydrothermal activities during the Paleocene-Eocene period. These volcanic activities in this case are considered influx of large masses of nutrients into the photic zone due to the ash accumulation. Therefore, high bio-productivity associated with effective OM preservation contributed to the organic carbon accumulation in the Palana Formation during the Paleocene-Eocene.

Tooth extraction is the most common procedure in dental practice. However, in the long term, it may cause alveolar ridge atrophy. This systematic review aimed to evaluate the role of platelet-rich fibrin (PRF) in post-exodontic alveolar ridge preservation in terms of its effectiveness in the regeneration of bone tissue as assessed by imaging and its efficacy compared to physiological bone healing. The study is presented in accordance with the preferred reporting items for systematic reviews and meta-analyses (PRISMA) guidelines. This systematic review was conducted using electronic databases such as PubMed, Scopus, Web of Science, and Science Direct. The grey literature search was conducted in the New York Academy of Medicine Grey Literature Report. All the studies in this systematic review were randomized controlled trials (RCTs). The risk of bias was performed according to the Cochrane Handbook for Systematic Reviews of Interventions 6.2 (RevMan 6.2). Considering the inclusion and exclusion criteria, we included 17 randomized clinical trials, published up to 2022 investigating the efficacy of PRF in post-exodontic bone regeneration. Based on the results of clinical studies, it can be stated that despite not being statistically significant, PRF promotes neoformation and prevents bone loss between three and four months post-extraction.

Fe- and Al-rich metapelite from the Transangarian segment of the Yenisey Ridge (East Siberia, Russia) is a potential new source of high-alumina refractories. The rocks have relatively high average contents of Al2O3 (20 wt.%) and Fe2O3 (7.91 wt%), moderate K2O (3.44 wt%), and low CaO (0.74 wt%). Their dominant mineral assemblages are andalusite + muscovite + margarite + chlorite + biotite + quartz or staurolite + kyanite or/and andalusite + chlorite + muscovite + biotite + quartz with ±garnet and ±plagioclase. Al2SiO5 polymorphs occur as up to 1.5 cm andalusite porphyroblasts and partial or complete pseudomorphs after andalusite (kyanite and staurolite). Accessories include abundant Fe-Ti oxides and sporadic REE-, Y-, Ca-phosphates; sulfides are negligible. The composition of Al2SiO5 concentrates obtained in laboratory by heavy-media and magnetic separation from ≥0.06 mm fractions meet all requirements for raw material of this type: >56 wt% Al2O3, <42 wt% SiO2, <1 wt% Fe2O3, <1.2 wt% TiO2, and <0.2 wt% (CaO+MgO). The andalusite, kyanite, and mixed ores yield 0.7-4.1 wt%, 0.7-2.2 wt%, and 1.9-6.0 wt% of concentrate, respectively. The best-quality ores rich in Al2SiO5 polymorphs reside in zones of contact and/or dynamic metamorphism superimposed over regional metamorphism of Al-rich rocks.

Angiogenesis is new blood vessel formation from existing vessels and is a critical first step in tissue repair following chronic disturbances in healing and degenerative tissues. Chronic pathoanatomic tissues are characterized by a high number of inflammatory cells, overexpression of inflammatory mediators, such as tumor necrosis factor-α (TNF-α) and interleukin-1 (IL-1), the presence of mast cells, T cells, reactive oxygen species, and matrix metalloproteinases, and a decreased angiogenic capacity. Multiple studies have demonstrated that autologous orthobiological cellular preparations (e.g., platelet-rich plasma [PRP]) im-prove tissue repair and regenerate tissues. There are many PRP devices on the market. Unfortunately, they differ greatly in platelet numbers, cellular composition, and bioformulation. PRP is a platelet concentrate consisting of a high concentration of platelets with or without certain leukocytes, platelet-derived growth factors (PGFs), cytokines, molecules, and signaling cells. Several PRP products have immunomodulatory capacities that can influence resident cells in a diseased microenvironment, inducing tissue repair or re-generation. Generally, PRP is a blood-derived product, regardless of its platelet number and bioformulation, and the literature indicates both positive and negative patient treatment outcomes. Strangely, the literature does not designate specific PRP preparation qualifications that can potentially contribute to tissue re-pair. Moreover, the literature scarcely addresses the impact of platelets and leukocytes in PRP on (neo)angiogenesis other than a general one-size-fits-all statement that “PRP has angiogenic capabilities.” Here, we review the cellular composition of all PRP constituents, including leukocytes, and describe the importance of platelet dosing and bioformulation strategies in orthobiological applications to initiate angiogenic pathways that re-establish microvasculature networks, facilitating the supply of oxygen and nutrients to impaired tissues.

Converting biowaste into biochar and subsequently putting it into the soil are considered to be an effective approach to sequestrate carbon (C). However, biochar will inevitably undergo the aging process in soil, which influences its stability, and ultimately threatens its carbon sequestration ability. This study selected CaCl2 as exogenous additive of sewage sludge and bone dreg to quantify both surface C and bulk C stability in Ca-rich biochars under three aging processes (dry-wet aging, freeze-thaw aging, and natural aging in farmland soil), and revealed the influence mechanisms of exogenous Ca on biochar stability. Results showed that after dry-wet aging (25 rounds), freeze-thaw aging (25 rounds), and natural aging in different farmland soils (5 months), oxidized surface C in Ca-rich biochar decreased by 10~23%, 28~41%, and 0~74%, respectively, compared to that in pristine biochar, while oxidized bulk C decreased by 6~10%, 0~1%, and 0~35%, respectively. Under three aging processes, the surface C and bulk C stability in Ca-rich biochar were superior to that in corresponding pristine biochar, which was attributed to the “protective effect” of Ca-containing crystals on biochar surface, including CaO, Ca5(PO4)3Cl, Ca5(PO4)3(OH), Ca8H2(PO4)6·H2O and Ca10(PO4)6(OH)2. These Ca-containing crystals could block the connection between biochar-C and the external oxidizing environment, intervening the oxidation of C-C/C=C in biochar, but also prevented aging from damaging C structure of biochar, reducing the generation of fragmented structure. By comprehensively assessing surface C and bulk C stability under three aging processes, final C sequestration in Ca-rich biochar increased to 27~80%, compared to that in pristine biochar (23~74%). Therefore, Ca-rich biochar is more dominant than pristine biochar, considering C sequestration potential during long-term aging in soil.

Spider toxin SNX-482 is a cysteine-rich peptide that interferes with calcium channel activity by binding to voltage-sensing domains of CaV2.3 subtype. Two general binding mechanisms are present in nature: direct binding from the aqueous phase or through lateral diffusion from the membrane, the so-called reduction in dimensionality mechanism. In this work, via coarse-grained and atomistic molecular dynamics simulations, we have systematically studied the spontaneous partitioning of SNX-482 with membranes of different anionic compositions and explored via diffusional analysis both binding mechanisms. Our simulations revealed a conserved protein patch that inserts within the membrane, a preference for binding towards partially negatively charged membranes, and that electrostatics drives membrane binding. Finally, diffusivity calculations showed that the toxin diffusion along the membrane plane is an order of magnitude slower than the aqueous phase suggesting that the critical factor in determin-ing the SNX-482-CaV2.3 binding mechanism is the affinity between the membrane and SNX-482

At present, the drilling rig for deep seabed shallow strata is widely used in the exploration of ocean cobalt-rich crust resources and other fields, which not only can obtain solid core samples at a specific station, but the operation process is relatively safe. This paper mainly presents the structure and mechanism of mobile drilling rig in acquiring the seafloor cores (up to 1.5 m long). Based on the function of the AMESim software, the hydraulic propulsion system model of mobile drilling rig is established, which is the basis and core part of the mobile drilling rig. Moreover, the control methods of closed-loop and PID are respectively used to control the hydraulic propulsion system for simulation analysis. Through the comparison of simulation results, it is found that the PID control method is more convincing in verifying the design rationality of hydraulic propulsion system. In the simulation of the PID-controlled hydraulic propulsion system, the co-simulation technology of AMESim and Matlab/Simulink not only establishes the hydraulic model and control model, but also determines the relevant simulation parameters, which is helpful to improve the system simulation efficiency. In its verification deployment in the South China Sea, the mobile drilling rig has been operated for many times at different depths, and some cores have been successfully obtained. Furthermore, the mobile drilling rig has been used during the 55th Voyage of China Oceanic Scientific Expedition supported by China Ocean Mineral Resources R&D Association. Several sites were explored and a large number of cobalt-rich crust cores were obtained. The powerful theory and sea trails are provided to support for the further research on survey of the abyssal resource.

There is a marked momentum towards the use of clean hydrogen energy as an alternative for fossil fuels. Renewable energies such as solar and wind are being used to generate hydrogen from the water hydrolysis process. Indeed, this approach stores renewable energies in the form of combustible hydrogen for other energy uses. The other alternative that could be economically more cost-effective at the current technology stage is to explore the natural “Hydrogen System” where the natural hydrogen is generated and accumulated within the earth system, the same that stands for a “Petroleum System”. The Discovery of a large accumulation of relatively pure natural hydrogen (H2) in Mali has triggered the opportunity of searching for natural hydrogen accumulations in other countries. The generation of hydrogen from a circular depression in Mali and some other countries is linked to the presence of geologically very old iron-rich basement rocks. Solid-liquid redox reactions between iron-rich minerals and groundwater that split water are a possible source of H2 in deep basement rocks. It is believed that the hydrogen degassing may be detected by surface topographic circular to sub-circular shallow depressions. Chemical processes such as dissolution by hydrogen are considered to play the main role in the formation of the circular depressions through preferential vertical hydrogen migration channel. Archean iron-rich Yilgarn Craton that covers a vast area of Western Australia (WA) contains abundant iron-rich mafic-ultramafic rocks. The craton reveals many surficial circular depressions visible through satellite images. The area has abundant fault systems and is blanketed with Eocene sedimentary rocks containing high-quality reservoir rocks. All these characteristics seem to provide most of the required elements, such as hydrogen source, migration pathway, and reservoir rock for a “Hydrogen System” in this area.

Rare earth rich magnesium alloys are used in aerospace and automotive fields because of their high specific strength and good castability. However, due to their low corrosion resistance, protective surface treatments, such as conversion coating or electroless plating are necessary, when they have to be used in humid or corrosive environments. The present study was aimed to evaluate the effect of Plasma Electrolytic Oxidation (PEO) and different surface roughness (Ra≈0.8 μm and Ra≈0.3 μm) on the rotating bending fatigue of an innovative Mg alloy, with a high content of Nd (up to 3.1 wt%) and Gd (up to 1.7 wt %). Fatigue tests revealed a 15% decrease in the fatigue strength of the PEO treated alloy (fatigue strength = 88 MPa) with respect to the bare alloy (fatigue strength = 103 MPa). The reduction of fatigue strength was mainly due to the residual tensile stresses induced by the PEO treatment. The effect of surface roughness on the bare alloy was, instead, negligible. The mechanisms of crack initiation were similar in the untreated and PEO treated alloy, with crack nucleation sites located in correspondence of large facets of the cleavage planes.

Fibrin rich of platelets (PRF^®) of Choukroun represents a new step in the therapeutic concept of platelet gel with a simplified processing and biochemical changes little artificial. A valid method of preparation of the PRF must effectively separate the plates by erythrocytes and concentrate without damaging or lysing the plates themselves. In this study the experimental design is to standardize the production of L-PRF in horse directing it to human production. Our hypothesis is that the L-PRF is easy to produce in the horse, without modifications of the human protocol, thus allowing a better standardization of the human protocol. A new device for the preparation and the standardization of L-PRF clots and membranes is the L-PRF Wound Box^®. The optical microscopy, most cell bodies were highlighted concentrated in the proximal portion of each membrane, the last 1/4 was observed at the center; the distal part had only residual traces of cell bodies. The L-PRF will form constantly when the phases described above are strictly adhered to. The success of the art L-PRF depends entirely on the speed of blood collection and transfer in centrifuge within a minute and by a temperature of centrifugation and compression is higher than 21°C (between 21 and 30°C). Our experiments on the horse will no doubt be able to improve our understanding on wound healing, in particularly in chronic skin lesions therapy.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Lithium-ion (Li-ion) batteries are becoming more common in portable electronic devices due to their high energy density, lack of memory effect, and high charge and discharge rate capabilities. Li-ion batteries are a relatively new technology, first marketed in the early 1990s, and research and development work are ongoing to improve safety and increase capacity, charge/discharge rate, and lifetime [1]. In this paper, we review the types and characteristics of Li-ion batteries and summarize charging methods and safety considerations. Following, we design and fabricate Li-ion battery and highlight the steps of fabrication that ensure fast charge/discharge rates that give the battery more reliability and high energy density

In this study, Li-Al-OH layered double hydroxide (LDH), which was prepared by solvent-free one-step mechanochemical reaction of LiOH and Al(OH)₃, was applied to remove boron from aqueous solution. Dry-grinding for 3 h at a rotational speed of 500 rpm, Li/Al molar 1/2 was the optimum condition to prepare highly crystalline of Li-Al LDH phase with no evident impure phases. Two milling products with Li/Al molar ratio at 1/2 and 2/2 were evaluated for boron adsorption. The results confirmed that Li/Al molar ratio 2/2 sample showed high boron adsorption capacity due to the physical adsorption of Li-Al-OH LDH and chemical synergism of phase gel Al(OH)₃. The adsorption isotherms, described by the Langmuir model, indicated maximum monolayer boron uptake capacity 45.45 mg/g, implying competitive adsorption capacity of the material in our experiment.

Li-ion cell designs, component integrity and manufacturing processes all have critical influence on the safety of Li-ion batteries. Any internal defective features that induce a short circuit, can trigger a thermal runaway: a cascade of reactions, leading to a device fire. As consumer device manufacturers push aggressively for increased battery energy, instances of field failure are increasingly reported. Notably Samsung made a press release in 2017 following a total product recall of their Galaxy Note 7 mobile phone, confirming speculation that the events were attributable to the battery and its mode of manufacture. Recent incidences of battery swelling on the new iPhone 8 have been reported in the media, and the techniques and lessons reported herein may have future relevance. Here we look deeper into the key components of one of these cells and confirm evidence of cracking of electrode material in tightly folded areas, combined with a delamination of surface coating on the separator, which itself is an unusually thin monolayer. We report microstructural information about the electrodes, battery welding attributes and thermal mapping of the battery whilst operational. The findings point to the most likely combination of events and highlights the impact of design features, whilst providing structural considerations most likely to have led to the reported incidences relating to this phone.

Hydrogenated water has emerged as a novel approach in the field of health and wellness. It is be-lieved to have potent antioxidant properties that can neutralize harmful free radicals in the hu-man body. It has also been shown to be beneficial in mitigating oxidative stress-induced damage through its anti-inflammatory and anti-apoptotic pathways. We aim to conduct a systematic re-view to evaluate the potential benefits of hydrogenated water. The review protocol was uploaded on PROSPERO. After the initial search criteria, the articles were reviewed by two blinded inves-tigators, and a total of 25 articles were included in the systematic review. The potential benefits of hydrogenated water on various aspects of health, including exercise capacity, physical endurance, liver function, cardiovascular disease, mental health, COVID-19, oxidative stress, and anti-aging research, are a subject of growing interest and ongoing research. Although preliminary results in clinical trials and studies are encouraging, further research with larger sample sizes and rigor-ous methodologies is needed to substantiate these findings. Current research needs to fully ex-plain the mechanisms behind the potential benefits of hydrogenated water. Continued scientific exploration will provide valuable insights into the potential of hydrogenated water as an adjunc-tive therapeutic approach in the future.

Our skin is constantly exposed to blue light (BL), which is abundant in sunlight and emitted by digital devices. Prolonged exposure to BL can lead to oxidative stress-induced damages and skin hyperpigmentation. In this study, we investigated the protective effects of tocotrienol-rich fraction (TRF) on BL-induced oxidative stress and hyperpigmentation in B16-F1 melanocytes. Alpha-tocopherol (αTP) was used as a comparator. Our results showed that TRF effectively suppressed the formation of reactive oxygen species, and preserved the mitochondrial membrane potential. Additionally, TRF exhibited anti-apoptotic properties by reducing the activation of p38 mitogen-activated protein kinase molecule and downregulating the expression of cleaved caspase-3. Moreover, TRF modulated tyrosinase activity, resulting in a lowered rate of melanogenesis and reduced melanin production. In contrast, αTP did not exhibit the significant protective effects against skin damages and pigmentation in BL-induced B16-F1 cells. Therefore, this study indicates that TRF may offer superior protective effects over αTP against the effects of BL on melanocytes. These findings demonstrate the potential of TRF as a protective natural active against BL-induced skin damages and hyperpigmentation via its antioxidative and anti-melanogenic properties.

Atherosclerotic cardiovascular disease (ASCVD) remains the leading cause of death worldwide and the risk of a major cardiovascular event is highest among those with established disease. Ongoing management of these patients relies on the accurate assessment of their response to any prescribed therapy, and their residual risk, in order to optimize treatment. Recent international guidelines and position statements concur that the plasma concentration of apolipoprotein B (apoB) is the most accurate measure of lipoprotein associated ASCVD risk. This is especially true for the growing number of individuals with diabetes, obesity or the metabolic syndrome, and those on statin therapy. Most guidelines, however, continue to promote LDL-C as the primary risk marker due to uncertainty as to whether the greater accuracy of apoB is sufficient to warrant a paradigm shift. Recommendations regarding apoB measurement vary, and the information provided on how to interpret apoB results is sometimes insufficient, particularly for the non-lipid specialist. Misinformation regarding the reliability of the assays is also frequently repeated despite its equivalent or better standardization than many other diagnostic assays. Thus, demand for apoB testing is relatively low, which means there is little incentive to increase its availability or reduce its cost. In this review, we examine the results of recent clinical outcomes studies and meta-analyses on the relative values of apoB, LDL-C and non-HDL-C as markers of ASCVD risk. Although there is seemingly minimal difference among these markers when only population-based metrics are considered, it is evident from our analysis that, from a personalized or precision medicine standpoint, a great many individuals would benefit, at a negligible total cost, if apoB measurement were better integrated into the diagnosis and treatment of ASCVD.

Wheat has a large and diverse repertoire of NLRs involved in disease resistance, with over 1,500 NLRs detected in some studies. These NLR genes occur as singletons or clusters containing copies of NLRs from different phylogenetic clades. The number of NLRs and cluster size can differ drastically among ecotypes and cultivars. Primarily, duplication has led to the evolution and diversification of NLR genes. Among the various mechanisms, whole genome duplication (WGD) is the most intense and leading cause, contributing to the complex evolutionary history and abundant gene set of hexaploid wheat. Tandem duplication or recombination is another major mechanism of NLR gene expansion in wheat. The diversity and divergence of duplicate NLR genes are responsible for the broad-spectrum resistance of most plant species with limited R genes. Understanding the mechanisms underlying the rapid evolution and diversification of wheat NLR genes will help improve disease resistance in crops. The present review focuses on the diversity and divergence of duplicate NLR genes and their contribution to wheat disease resistance. Moreover, we provide an overview of disease resistance-associated gene duplication and the underlying strategies in wheat.

Taking a socio-technical perspective, I focus on solar businesses (niche market actors) in Iran. As one of the key stakeholder groups whose business prosperity is tied to the development of solar PV, they play a crucial role in accelerating the energy transition. Given the incumbent fossil-based electricity sector in Iran and the least enabling policies, I am first interested to find (i) the main drivers and barriers of solar businesses; and (ii) the roles these solar businesses play in bringing solar PV deployment forward in Iran. I collected the data via 20 semi-structured interviews with solar businesses in Golestan, Guilan, Tehran, Khorasan Razavi, and Eastern Azerbaijan Provinces in Iran. Taking an inductive approach, I considered sustainability transition and social acceptance theories as sensitising concepts to investigate common and specific points of solar business acceptance in Iran. I find ecological awareness, belief in intergenerational justice, and willingness to innovate, as the main intrinsic drivers and socioeconomic opportunity and tackling the energy imbalance as extrinsic drivers; while the lack of a common vision with the energy governors, and the low knowledge of solar PV among the customers, escalating prices, and challenges to accessing good quality solar equipment are the most prior obstacles. Moreover, I understand educating people, driving the innovative deployment of solar PV, and facilitating the diffusion of it, as the major roles of solar businesses in Iran. I find that the sustainability transition literature overlooked the key role of solar businesses specially in fossil-based and developing economies. My findings suggest that the positive intrinsic mechanisms among the solar businesses, in combination with better-enabling policy frameworks and external factors, like lifting the sanctions and joining the global energy market, climate change mitigation commitments and standards, can help solar businesspeople to lead and accelerate solar PV development in Iran.

The supposition is that the usage of fibrin rich in leukocytes and platelets advanced (A-PRF) in ulcerative osteomyelitis of the diabetic foot allows rehabilitation from this critical illness. In this investigation, the focus was to normalize the use of PRF in patients with osteomyelitis not amputated, to use this second generation platelet concentrate as a regeneration enabler. The researchers submitted and utilized A-PRF membranes (1300 g × 8 min) in 7 patients (all diabetics) with osteomyelitis and cutaneous injury for 6 months. The membranes, in combination with the supernatant fluid produced by stress, have been integrated into the skin lesion down to the bone after surgical debridement. The advancement of the lesions after some period of time has been analyzed. All seven subjects had a Probe-to-Bone positive assay; MRI indicated a cortico-periosteal coagulation and/or foci of cortico-spongeous osteolysis contiguous to the lesion. Gram-positive bacterium were identified in our procedures in 52% of cases. Gram+ Cocci, for example, S. Aureus (15.6%), S. Hemolytic (12.1%), S. Viridans (7.1%), and Gram-negative Bacteria, for example, Pseudomonas (10.6%), Proteus (7.8%), Enterobacter (5.7%) are present. Candida Albicans is active in 2.8%. The blood count shows no relevant differences. To date, cutaneous lesions have cured in 6 of the seven subjects treated (one patient for more than five years) without any evidence of infection or recurrence. The results obtained on our subjects indicate that PRF membranes may be a therapeutic option in this problematic disease.

This study aimed to investigate the healing effect of advanced platelet-rich fibrin (A-PRF) clot membranes in the reduction of palatal wounds resulting from free gingival graft (FGG) harvesting, in the re-epithelization rate and in the pain experience after surgery. Twenty-five patients requiring soft tissue augmentation (gingival recession coverage or keratinized gingiva augmentation) participated in this prospective randomized clinical study. After FGG harvesting, the test group (n=14) received A-PRF clot membranes at the palatal wound and the control group (n=11) a gelatin sponge. Epithelialization rate of the palatal wound, wound healing area, correspondent percentage of reduction and post-surgical pain experience were assessed. The follow-up period was 90 days. There was a significantly higher reduction of the palatal wound area in the A-PRF group vs. the control group, at 7 (p<0.001), 14 (p=0.009) and 30 days (p<0.001) follow-up. The maximum difference between groups was attained at 30 days (91.5% for A-PRF vs. 59.0% for the control group). At 14 days a significant difference in the proportion of patients showing total epithelization was found: 64.3% for A-PRF vs. 9.1% for the control group (p=0.012). At 90 days, both groups showed total recovery. Overall, the control group experienced a higher level of pain and discomfort until the 14th day, being significantly higher on the second day (p=0.013). The results suggest that A-PRF membranes haste the healing process by promoting a greater reduction along the recovery period and an apparent less painful postoperative period.

Microporous organic polymers (MOPs) are promising materials for gas sorption because of the intrinsic and permanent porosity, designable framework and low density. The introduction of nitrogen-rich building block in MOPs will greatly enhance the gas sorption capacity. Here, we report the synthesis of MOPs from the 2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine unit and aromatic azides linkers via click polymerization reaction. FTIR and solid state 13C CP-MAS NMR confirm the formation of the polymers. CMOP-1 and CMOP-2 exhibit microporous networks with BET surface area of 431 and 406 m2 g-1 and narrow pore size distribution under 1.2 nm. Gas sorption isotherms including CO2 and H2 were measured. CMOP-1 stores superior CO2 level of 8.2 wt% (1.88 mmol g-1) at 273 K/1.0 bar and H2 uptake up to 0.6 wt% at 77 K/1.0 bar, while CMOP-2 with smaller surface area shows lower CO2 adsorption capacity of 7.3 wt% (1.66 mmol g-1) and H2 uptake (0.5 wt%). In addition, I2 vapor adsorption was tested at 353 K. CMOP-1 shows higher gravimetric load of 160 wt%. Despite of the moderate surface area, the CMOPs display excellent sorption ability for CO2 and I2 due to the nitrogen-rich content in the polymers.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

The search for new materials that could improve the energy density of Li-ion batteries (LIB) is one of today’s most challenging issues. Recently, cation-disordered lithium-excess metal oxides have emerged as a promising new class of cathode materials for LIB, due to their high reversible capacities and nice structural stability. However, a full structural model of the Li-transition metal (TM) sharing sublattice and the origin of short range ordering (SRO) of cation ions requires further investigation. In this work, we put forward a Monte Carlo strategy of building a cation-disordered rocksalt material supercell model. The cation ions of Li_1.0Ti_0.5Ni_0.5O₂ (LTNO) are placed at the FCC sublattice sites with the constraint of Pauling’s electroneutrality rule, instead of a random way. This constraint causes the Li-Ti and Ni-Ni clustering (the cation short range ordering). Based on this model, we discussed the relationship between the short range ordering, the local distorting, the theoretic capacity and the order-disorder strengths. A unified understanding of these factors in cation-disordered materials may enable a better design of disordered-electrode materials with high capacity and high energy density.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

The aim of this study was to compare the effect of using L-PRF in patients undergoing impacted lower third molar surgery with either primary or secondary closure techniques. Methods: This prospective, randomised, double-blind, split-mouth clinical trial was conducted in patients with bilateral lower impacted third molars of similar position. Primary closure was performed in group 1 and secondary closure in group 2. Group 1 closure technique was applied to one side of the patients and group 2 closure technique was applied to the other side at different times. Nine pa-tients were excluded from the study due to alveolitis and failure to attend regular control visits out of the 45 patients evaluated. Results: Of the 36 patients included in the study, 23 were female and 13 were male and the mean age was 22.42±3.36 years. The secondary closure group had lower VAS scores at hour 6 (p

Abstract: Kiwifruit, a perennial horticultural crop known for its nutritional value, faces significant challenges due to biotic and abiotic stresses, affecting its yield and quality. Leucine-rich repeat receptor-like proteins (LRR-RLPs), a major group of receptor-like proteins in plants, have diverse functions in plant physiology, including growth, development, signal transduction, and stress responses. Despite their importance, the specific roles of kiwifruit LRR-RLPs in response to biotic and abiotic stresses remain poorly understood. In this study, we investigated the expression patterns of kiwifruit LRR-RLPs under various stress conditions, including pathogen stress, heat stress, waterlogging stress, and copper stress. Through genome and transcriptome analyses, we identified a total of 101, 164, and 105 LRR-RLPs in Actinidia Chinensis 'Hongyang', Actinidia eriantha 'Huate', and Actinidia chinensis 'Red5' kiwifruit, respectively, classified into 9 subgroups based on phylogenetic relationships. Synteny analysis revealed that the expansion of kiwifruit LRR-RLPs was primarily attributed to segmental duplication events. Using RNA-seq data from pathogen-infected kiwifruits, we identified specific LRR-RLP genes potentially involved in different stages of pathogen infection. Additionally, we observed the potential involvement of kiwifruit LRR-RLPs in abiotic stress responses, with upstream transcription factors possibly regulating their expression. Furthermore, protein interaction network analysis unveiled the participation of kiwifruit LRR-RLP genes in the regulatory network of abiotic stress responses. These findings highlight the crucial roles of LRR-RLPs in mediating both biotic and abiotic stress responses in kiwifruit, offering valuable insights for the breeding of stress-resistant kiwifruit varieties.

The present study evaluated the antioxidant, antidiabetic properties, and biocompatibility of Medicago sativa and Solidago virgaurea extracts enriched in flavonoid and isoflavonoid compounds. The extracts were obtained by accelerated solvent extraction and laser irradiation. Then, nanofiltration was used for the concentration of flavonoid and isoflavonoid compounds from extracts. The extracts were analyzed for antioxidant capacity using DPPH radical scavenging and reducing power methods, while the antidiabetic property was tested by α-amylase and α-glucosidase inhibition and in vitro on a murine insulinoma cell line (β-TC-6). M. sativa obtained by laser irradiation and concentrated by nanofiltration had the highest DPPH• scavenging (IC50 = 105.2±1.1 and reducing power activities (IC50 = 40.98±0.2 µg/mL). M. sativa extracts had higher inhibition on α-amylase (IC50 = 23.9±1.2, respectively 26.8±1.1), while S. virgaurea had the highest α-glucosidase inhibition (9.3±0.9 ?g/mL respectively 8.6±0.7 ?g/mL). The results obtained after evaluating the antidiabetic in vitro activity showed that the treatment with M. sativa and S. virgaurea flavonoid- and isoflavonoid-rich extracts stimulated the insulin secretion of β-TC-6 cells, both under normal conditions as well as in hyperglycemic conditions. This paper argued that M. sativa and S. virgaurea flavonoid-rich and isoflavonoid-rich extracts could be an excellent natural source with promising antidiabetic potential.

Superconductivity in highly-pressurized hydrides became primary direction for the exploration of fundamental upper limit for the superconducting transition temperature, Tc, after Drozdov et al (Nature 2015, 525, 73) discovered superconducting state with Tc=203 K in highly-compressed sulphur hydride. To date several dozens of high-temperature superconducting polyhydrides have been discovered. In addition, recently, it was reported that highly-compressed titanium and scandium exhibit record-high (up to 36 K), which is by manifold exceeded of niobium, which is the record high- ambient pressure metallic superconductor. Here we analysed experimental data on for recently discovered high-pressure superconductors (which exhibit high transition temperatures within their classes): elemental titanium (Zhang et al, Nature Communications 2022; Liu et al, Phys. Rev. B 2022), TaH3 (He et al, Chinese Phys. Lett. 2023), LaBeH8 (Song et al, Phys. Rev. Lett. 2023), and black (Li et al, Proc. Natl. Acad. Sci. 2018) and violet (Wu et al, arXiv 2023) phosphorous, to reveal the nonadiabaticity strength constant, TθTF (where Tθ is the Debye temperature, and TF the Fermi temperature) in these superconductors. The analysis showed that δ-phase of titanium and black phosphorous exhibit the Tθ/TF which are nearly identical to ones associated in A15 superconductors, while studied hydrides and violet phosphorous exhibit the constants in the same ballpark with H3S and LaH10.

Molecular hydrogen (H2) has been shown to have antioxidant and anti-inflammatory activities that may reduce the development and progression of many diseases. In this study, Hydrogen-rich water (HRW) was obtained by reacting hybrid magnesium-carbon hydrogen storage materials with water. Then the effects of intake of HRW on the activities of xenobiotic-metabolizing enzymes, membrane transporters, and oxidative stress in rats were investigated. Rats were given HRW ad libitum for 4 weeks. Results showed that intake of HRW had no significant effect on the activities of various cytochrome P450 (CYP) enzymes (CYP1A1, 1A2, 2B, 2C, 2D, 2E1, 3A, 4A), glutathione-S-transferase and UDP-glucuronosyltransferase. Except for a slight lower plasma glucose concentration, intake of HRW had no effect on other plasma biochemical parameters in rats. P-Glycoprotein and multidrug resistance-associated protein (Mrp)2 protein expressions in liver were elevated after intake of HRW. However, HRW had no significant effects on glutathione, glutathione peroxidase, or lipid peroxidation in liver. Results from this study suggest that consumption of HRW may not affect xenobiotic metabolism or oxidative stress in liver. However, intake of HRW may increase the efflux of xenobiotics or toxic substances from the liver into bile by enhancing the expression of p-glycoprotein and Mrp2 protein.

Li₂TiO₃ nanopowders were synthesized by hydrothermal process using anatase TiO₂ and LiOH H₂O as raw materials. Li₂TiO₃ crystallizes in the layered monoclinic structure (space group C2/c) with average crystallite size of 34 nm. Morphology, elemental composition and local structure of products were carried out using HRTEM, FESEM, EDS, Raman and FTIR spectroscopy. Transport properties investigated by d.c. (4-probe measurements) and a.c. (complex impedance spectroscopy) show the activation energy of 0.71 and 0.65 eV, respectively. The ionic transport properties of Li⁺ ions in nanocrystalline Li₂TiO₃ characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) validate the good electrochemical properties of this anode material for lithium-ion batteries.

The semantic segmentation of high-resolution remote sensing images (HR-RSI) is crucial for a wide range of applications, such as precision agriculture, urban planning, natural resource assessment, and ecological monitoring. However, accurately classifying pixels in HR-RSI faces challenges due to densely distributed small objects and scale variations. Existing techniques, including Convolutional Neural Networks (CNNs) and other methods for hierarchical feature extraction and fusion of remote sensing image, often do not achieve the desired accuracy. In this paper, we propose a novel approach called the Hierarchical Rich-scale Fusion Network (HRFNet) to address these challenges. HRFNet utilizes advanced information rating and image partition techniques to extract rich-scale features within image layers. This allows for the adaptive exploration of both local and global contextual information. Moreover, we introduce a structured intra-layer to inter-layer feature aggregation module, which enables the adaptive extraction of fine-grained details and high-level semantic information from multi-layer feature maps in a highly flexible manner. Extensive experimentation has been conducted to validate the effectiveness of our proposed method. Our results demonstrate that HRFNet outperforms existing techniques, achieving state-of-the-art (SOTA) results on benchmark datasets, specifically the ISPRS Potsdam and Vaihingen datasets.

In the crustacean immune system, leucine-rich repeat (LRR) is one of the major structures for recognizing pathogen-associated molecular patterns (PAMPs). LRR domain-containing proteins belong to the LRR family, which is a large group of proteins with more than 6000 genes in the database. They are involved in very diverse physiological functions mainly by interacting with other proteins. In a previous study, the LvLRRm, a transmembrane protein containing only LRR domain, was identified in the white leg shrimp, Litopenaeus vannamei. Its versatile role in performing multiple immunomodulation activities has been reported. However, there is still a lack of research on its efficient function at the protein level. To investigate its interactions with other proteins, we applied a convenient method called ‘Hybrid LRR technique’ to produce a recombinant LvLRRm. The LvLRRm and hagfish’s variable lymphocyte receptors (VLRs) fragments were fused to the conserved LxxLxLxxN motif while retaining the β-strand. In addition, we established interactions between hybrid-proteins and flagellin of Salmonella by performing surface plasmon resonance (SPR) analysis. The designed hybrid proteins showed potential for universal applications without losing protein functions.

Objective: To describe technique of platelet rich plasma injection into the olfactory cleft in patients with long-term COVID-19 olfactory dysfunction. Methods: The technique starts with the blood extraction and the isolation of PRP through a 10-min centrifugation (4,200 rpm). The supernatant was injected in nasal regions with a 27-G needle after a local anesthesia with Xylocain 10% spray. The injection was performed through a 0° rigid optic. Precisely, several points of 0.2–0.5 mL were performed in the nasal septum in regard of the head of the middle turbine, and in the head of the middle turbine in both sides. Clinical, psychophysical and pain outcomes were evaluated pre- to post-injection. Results: A 22-year-old female with 24-month post-COVID-19 anosmia was recruited for the injection of PRP. The olfactory cleft endoscopic scale score was 0 and the threshold, discrimination and identification scores were 1, 8 and 0, respectively. The Olfactory Disorder Questionnaire score was 51. The patient benefited from the injection of 2.2 mL of PRP in nasal regions, which was done without complication. The procedure pain level was 2/10, while the local anesthesia with xylocaine 10% was judged as the most annoyance step with a score of 3/10. At 2-month post-injection, the TDI scores reached 16, 16, and 16 (48), while the Olfactory Disorder Questionnaire was 73. The patient described its recovery as very rapid, lasting 3-4 days, and occurring 3-week post-injection. Conclusion: The injection of PRP into the olfactory cleft is a safe and easiness new approach that may improve the recovery of smell sense.

Satterthwaite and Toepke (1970 Phys. Rev. Lett. 25 741) discovered that Th₄H₁₅-Th₄D₁₅ superhydrides exhibit superconductivity and have no isotope effect. The latter is fundamental contradiction with the concept of electron-phonon mediated superconductivity of Bardeen-Cooper-Schrieffer (BCS) theory. Soon after this work, Stritzker and Buckel (1972 Zeitschrift für Physik A Hadrons and nuclei 257 1-8) reported that superconductors in PdH_x-PdD_x system exhibit reverse isotope effect. Yussouff et al (1995 Solid State Communications 94 549) extended this finding on PdH_x-PdD_x-PdT_x system. Recent interest to hydrogen- and deuterium-rich superconductors is based on the discovery of near-room-temperature superconductivity in highly-compressed H₃S (Drozdov et al. 2015 Nature 525 73) and LaH₁₀ (Somayazulu et al 2019 Phys. Rev. Lett. 122 027001). To date, there is no clarity about isotope effect in H₃S-D₃S system, because thorough examination of available experimental data reported by Drozdov et al (2015 Nature 525 73) shows that H₃S-D₃S system perhaps has reverse isotope effect. In attempt to reaffirm/disprove our primary idea that the mechanism for near-room-temperature superconductivity in hydrogen-rich superconductors is not BCS electron-phonon interaction, we analyse the upper critical field data, B_c2(T), in Th₄H₁₅-Th₄D₁₅ phases (Satterthwaite and Toepke 1970 Phys. Rev. Lett. 25 741) and two recently discovered high-pressure hydrogen-rich phases of ThH₉ and ThH₁₀ (Semenok et al 2019 arXiv:1902.10206). As the result, it is found that all known to date thorium super-hydrides/deuterides are unconventional superconductors which have T_c/T_F ratios within a range of 0.008 < T_c/T_F < 0.120, where T_c is the superconducting transition temperature and T_F is the Fermi temperature.

Aedes aegypti (L.) is the primary vector of chikungunya, dengue, yellow fever and Zika viruses. The leucine-rich repeats (LRR)-containing domain is evolutionarily conserved in many proteins associated with innate immunity in invertebrates and vertebrates, as well as plants. We focused on the AaeLRIM1 and AaeAPL1 gene expressions in response to Zika virus (ZIKV) and Chikungunya virus (CHIKV) infection using a time course study, as well as the developmental expressions in the eggs, larvae, pupae, and adults. RNA-seq analysis data provided 60 leucine-rich repeat related transcriptions in Ae. aegypti in response to Zika virus (Accession number: GSE118858, https://www.ncbi.nlm.nih.gov/gds/?term=GSE118858). RNA-seq analysis data showed that AaeLRIM1 (AAEL012086-RA) and AaeAPL1 (AAEL009520-RA) were significantly upregulated 2.5 and 3-fold during infection by ZIKV 7-days post infection (dpi) of an Ae. aegypti Key West strain compared to an Orlando strain. The qPCR data showed that LRR-containing proteins AaeLRIM1, AaeAPL1 and five paralogues were expressed 100-fold lower than other nuclear genes, such as defensin, during all developmental stages examined. Together, these data provide insights into transcription profiles of LRR proteins of Ae. aegypti during its development and in response to infection with emergent arboviruses.

Titanium dioxide (TiO₂) micro and nano architectures have been intensively studied in the past years because of many varied applications in environmental, energy conversion, and storage fields, such as heterogeneous catalysis, dye-sensitized solar cells, lithium/sodium ion batteries, lithium-sulfur (Li-S) batteries, and bio-nanotechnology, etc. Especially the surface and interface structures in the TiO₂ structures play important roles in those applications. This mini review article focuses on TiO₂ micro and nano architectures with the prevalent crystal structures (anatase, rutile, brookite, and TiO₂(B)), and summarizes major advances in the surface and interface engineering and applications in environmental and electrochemical applications. We present the principles and growth mechanisms of TiO₂ nanostructures via different strategies, with an emphasis on rational control of the surface and interface structures. We further discuss the applications of TiO₂ micro and nano architectures in photocatalysis, lithium/sodium ion batteries, and Li-S batteries. Throughout the discussion, the relationship between the device performance and the surface structures of TiO₂ micro/nano structures will be highlighted. Then we discuss the phase transitions of TiO₂ nanostructures and possible strategies of improving the phase stability. The review concludes with a perspective on the current challenges and future research directions.

The heavy transition metal tantalum (Ta) offers a wide range of applications, especially in the field of electronics, e.g. Ta capacitors with a comparatively long life-time. Therefore, electronic scrap containing these components is a potentially valuable secondary source of this metal. However, the recovery of Ta, as other critical raw materials, that are lost in pyrometallurgical slags can be a challenging process. As a way of overcome this, the "engineered artificial minerals" EnAM approach is proposed by first searching for suitable host minerals and characterizing them. A favorable prerequisite is the enrichment of the desired element(s) in compounds that have particularly suitable properties for this purpose, such as morphology, crystal size, surface or magnetic properties. Subsequently, the slag system is adapted (e.g. chemism, solidification curve, cooling and holding times) to optimize this compound. This paper presents the results of mineralogical characterization of Ta-containing iron (Fe)-rich synthetic slags in reducing environment under different cooling rates, and describes and discusses the incorporation of Ta into the different compounds detected by powder X-ray diffraction (PXRD) and electron beam microanalysis (EPMA). Additionally, the speciation of Fe and Ta was accessible through X-Ray absorption near edge structure (XANES) spectroscopy. EPMA also provides a first semi-quantitative assessment of the Ta distribution in these individual compounds. According to this, depending on the cooling rate the enrichment factor is highest in tantalite/perovskite-type oxides (FexTayO6, CaxFeyTazO3) with up to 60 wt.% Ta and ‘tantalomagnetite’ (FeII(FeIII(2-5/3xTax)O4) with a maximum of ~ 30 wt.% Ta (only fast cooling). This is followed by a perovskite-like silicon containing oxide (XYO3) with 12-15 wt.-% Ta (only slow cooling), and a hedenbergite-like compound (XYZ2O6) with varying content of 0.3 - 7 wt.-%. The Ta-concentration in pure Fe, Fe(1-x)O, hercynitic spinel and hematite is negligible. Since a larger fraction of potentially amorphous hedenbergitic matrix is formed at faster cooling, in this case the main Ta is enriched in this compound despite the significantly lower Ta content.

The R23Cu7Mg4 (R = Ca, Eu) intermetallics, studied by single crystal X-ray diffraction, were found to be isostructural with the Yb23Cu7Mg4 prototype (hP68, k4h2fca, space group P63/mmc), forming a small group inside the bigger 23:7:4 family, otherwise adopting the hP68-Pr23Ir7Mg4 crystal structure. The observed structural peculiarity is connected with the divalent character of the R component and with a noticeable volume contraction, resulting in a clear clustering of title compounds inside the whole 23:7:4 family. The occurrence of fragments typical of similar compounds, particularly Cu-centered trigonal prisms and Mg-centered core-shell polyicosahedral clusters with R at vertices, induced the search of significant structural relationships. In this work, a description of the hexagonal crystal structure of the studied compounds is proposed as a linear intergrowth along the c-direction of the two types of slabs R10CuMg3 (parent type: hP28-kh2ca, SG 194) and R13Cu6Mg (parent type: hR60-b6a2, SG 160). The ratio of these slabs in the studied structure is 2:2 per unit cell, corresponding to the simple equation 2XR10CuMg3 + 2XR13Cu6Mg = 2XR23Cu7Mg4. This description assimilates the studied compounds to the (Ca,Eu,Yb)4CuMg ones, where the same slabs (of p3m1 layer symmetry) are stacked in a different way/ratio, and constitutes a further step towards a structural generalization of R-rich ternary intermetallics.

When developing bone implants Young's modulus is one of the primary characteristics of the material that should be considered. The study focuses on the possibility of regulating the modulus of the alloy Ti-50.8 at % Ni by varying its initial structure as well as aging-induced microstructure in a wide range. Microstructure observations were performed using TEM and SEM observations. The calorimetric studies of martensitic transformations were carried out using "Mettler Toledo 822e". Tensile tests were performed in a test temperature range of ‒196≤T≤+100°C using an «IN-STRON 5966». The grain/subgrain size of B2-austenite strongly affects the modulus magnitude. This effect is ambiguous for a material with a grain size of 0.13–3 µm and depends on the test temperature. The effectiveness of aging on the modulus reduction depends on the initial structure: it is most pronounced in an alloy with a relatively coarse grain size of 9 µm and brings a decrease by 3.8 times at a temperature of 37°C. Bone-like elastic modulus (10–30 GPa) at a human body temperature of 37°C is realized in an aged fine-grained NiTi alloy. An ultrafine-grained sub-structure exhibits he same values of Young's modulus in the temperature range from -100°С to 25°С.

Background: The liver is involved in disseminated tuberculosis in more than 80% of the cases while primary liver involvement is rare, representing < 1% of all cases. Hepatic tuberculosis (TB) can be treated by conventional anti-TB therapy, however, diagnosing this disease still remains a challenge. The diagnosis might be particularly difficult in patients with a single liver lesion that could be misdiagnosed as a tumor or other focal liver lesions. While computed tomography and magnetic resonance imaging findings have been described, there is a paucity of literature on contrast-enhanced ultrasound (CEUS) features of hepatic TB. Case Summary: herein, we describe a case of a patient with tuberculous lymphadenopathy and chronic HCV-related liver disease who developed a single macronodular hepatic TB lesion. Due to the finding of a hepatocellular carcinoma (HCC) highly suggestive CEUS pattern, specifically a LR5 category according to the Liver Imaging Reporting and Data System (LI-RADS), and a good response to antitubercular therapy, a non-invasive diagnosis of HCC was made, and the patient underwent liver resection. We also review the published literature on imaging features of hepatic TB and discuss the diagnostic challenge represented by hepatic TB when occurs as a single focal liver lesion. Conclusions: this report shows for the first time that CEUS pattern of hepatic TB might be misinterpreted as HCC and specific imaging features are lacking. Personal history and epidemiological data are mandatory in interpreting CEUS findings of a focal liver lesion even when the imaging pattern is highly suggestive of HCC.

Background: Obtaining adipose-derived stem cells is limited by its capacity to differentiate. Stimulation by platelet-rich fibrin appears to have the beneficial effects to accelerate differentiation. Objective: To obtain immunohistochemistry evidence of platelet-rich fibrin to accelerate differentiation of adipose-derived stem cells. Methods: We used post-test only controlled-group design. Adipose-derived stem cells were isolated and cultured until 4 passages in α-MEM culture medium. Results: GATA-4 expression increased in platelet-rich fibrin group compared with control group (68.20±6.82 vs 58.15±1.23 counts; p<0.05; 68.20±6.82 vs 52.96±2.02 counts; p<0.05). Troponin expression also increased in platelet-rich fibrin group (50.66±7.2 vs 10.73±2.39 counts; p<0.05; 50.66±7.2 vs 26.00±0.4 counts; p<0.05). Conclusion: There is an immunohistochemistry benefit of platelet-rich fibrin to accelerate differentiation of adipose-derived stem cells into cardiomyocyte-like cells.

The human polyamines spermine and spermidine are essential for cell function, and their properties have been extensively studied. However, research results of experiments conducted without understanding the properties of polyamines have been evaluated and published by reviewers who appear to have little knowledge of the properties of polyamines. It is sad that some studies repeat what was done more than half a century ago before polyamines were characterized. First, I explain the basic properties of polyamines that researchers need to know. Then, the relationship between changes in polyamine levels in the body and age- and lifestyle-related diseases is discussed. In addition, the epigenetic mechanism of action of polyamines in relation to healthy longevity and, conversely, age- and lifestyle-related diseases and the progression of senescence are discussed. Spermine, which increases with a polyamine-rich diet, acts to suppress aberrant gene methylation and proinflammatory status associated with aging. Meanwhile, chronic inflammation associated with aging induces the enzyme activity of spermine oxidase, which breaks down spermine and produces acrolein, resulting in reduced spermine levels. Acrolein, a toxic aldehyde that increases with age- and lifestyle-related diseases, is thought to accelerate these diseases.

Background: There is several challenges to solve irreversible loss of cardiomyocytes due to myocardial infarction. Cell therapy is believed as an ideal treatment for cardiac regeneration in the infarct area. Obtaining adipose-derived stem cells increases seems to be promising, however it is limited by the capacity to differentiate. Stimulation by injectable platelet-rich fibrin appears to have the beneficial effects to accelerate cardiomyocyte-like cells differentiation. Objective: To analyse the benefit of injectable platelet-rich fibrin to accelerate differentiation of adipose-derived mesenchymal stem cells into cardiomyocyte-like cells. Methods: This study is a true experimental randomized post-test design study. Adipose-derived mesenchymal stem cells were isolated from adipose tissues and cultured until 4 passages. The characteristics of adipose-derived mesenchymal stem cells were measured by the expression of CD 34-, CD 45-, and CD 105+ using flowcytometry. The samples were divided into 3 groups, i.e. negative control (α-MEM), positive control (differentiation medium) and treatment group (platelet-rich fibrin). The assessment of GATA-4 marker expression was conducted using flowcytometry on the fifth day and troponin was conducted using immunocytochemistry on the tenth day to determine the differentiation to cardiomyocyte. Data analysis was conducted using T-test and One-Way ANOVA on normally distributed data determined through Shapiro-Wilk test. Results: Flowcytometry on GATA-4 expression revealed significant difference on addition of platelet-rich fibrin compared with negative and positive controls (68.20 ± 6.82 vs 58.15 ± 1.23; p<0.05; 68.20 ± 6.82 vs 52.96 ± 2.02; p<0.05). This was supported by the results of immunocytochemistry on troponin expression which revealed significant difference between platelet-rich fibrin group compared with negative and positive controls (50.66 ± 7.2 vs 10.73 ± 2.39; p<0.05; 50.66 ± 7.2 vs 26.00 ± 0.4; p<0.05). Conclusion: Injectable platelet-rich fibrin has beneficial effect to accelerate differentiation of adipose-derived mesenchymal stem cells into cardiomyocyte-like cells.

A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitable homogenization temperature and duration is a crucial step in assuring a homogeneous distribution of alloying elements and optimal exploitation of the potential of the alloy. In-situ heating in an electron microscope was performed on a twin-roll cast Al-Cu-Li-Mg-Sc-Zr alloy to understand the peculiarities of the homogenization process. Four types of primary phase particles rich in Cu, Li, Mg, and Fe were identified in the as-cast material. They appear as coarse particles at the boundaries of eutectic cells. Their partial dissolution occurs at temperatures above 450 °C. They are almost fully dissolved at 550 °C, except for complex phases containing Fe and Cu. Small dimensions of eutectic cells in the range of 10 µm assure a homogeneous distribution of main alloying elements within the matrix after 20 min of annealing. Direct comparison with the same material prepared by mold-casting indicates that such short annealing times result in the dissolution of main primary phase particles but do not assure a homogeneous distribution of alloying elements in the whole volume of the specimen.

: Sulfate presence is of great importance for anaerobic digestion as its addition can control the anaerobic microbial community. In this study, the effect of sulfuric acid addition on the perfor-mance of an UASB reactor fed with hydrolyzed starch was investigated. TOC, Fe and SO4-2 re-moval as well as the methane production were monitored under various COD/ SO4-2 ratios, HRTs and OLRs. When HRT was 16 hours and OLR equal to 2 g COD/LUASB-d the methane production was 0.24 L CH4/LUASB-day. After the sulfuric acid addition, TOC removal reached 95%. At HRT, OLR, and COD/ SO4-2 ratio equal to 16 hours, 2 g COD/ LUASB-d and 3.72 respectively, the methane production was 0.267 L CH4/LUASB-d. When the OLR was increased to 5.94 g COD/LUASB-d and COD/SO4-2 ratio was equal to 12.5, the methane production was 3 times higher (0.84 L CH4/LUASB-d) with a methane content in the produced biogas greater than 70%. 16s rRNA gene analysis demonstrated that after the sulfate addition, SRB were enriched and methane was mainly produced by Methanosaeta sp. This study indicates that appropriate sulfate concentrations in the feed in combination with the presence of iron in the UASB reactor lead to enhanced me-thane yields.

Leucine-rich α-2 glycoprotein1 (LRG1) is a member of the leucine-rich repeat (LRR) family that was implicated in multiple diseases including cancer, aging and heart failure as well as diabetes and obesity. LRG1 plays a key role in diet-induced hepatosteatosis and insulin resistance by mediating the crosstalk between adipocytes and hepatocytes. LRG1 also promotes hepatosteatosis by upregulating de novo lipogenesis in the liver and suppressing fatty acid β oxidation. In this study, we investigated the association of LRG1 with obesity markers including leptin and other adipokines in adolescents (11-14 years; n=425). BMI-for-age classification based on WHO growth charts was used to define obesity. Plasma LRG1 was measured by ELISA while other markers were measured by multiplexing assay. Median (IQR) of LRG1 levels was higher in obese [30 (25, 38) µg/mL] and overweight [30 (24, 39) µg/mL] adolescents, compared to normal-weight participants [27 (22, 35) µg/mL]. The highest tertile of LRG1 had an OR [95%CI] of 2.55 [1.44, 4.53] for obesity. LRG1 was positively correlated to plasma levels of HsCRP (R=0.2), Leptin (R=0.2) and Chemerin (R=0.24) with p<0.001. Additionally, it was positively associated with plasma level of IL6 (R=0.17) and IL10 (R=0.14) but not TNF-α. In conclusion, LRG1 levels are increased in obese kids and associate with increased levels of adipogenic markers. These results suggest the usefulness of LRG1 as an early biomarker for obesity and its related pathologies in adolescents.

Administration of crude polysaccharides extract from natural product is a promising gut microbiota-targeted approach to preventing obesity and associated metabolic disorders. Dietary restrictions can change the type and number of gut bacteria, which is an important factor in delaying the onset and burden of diseases. This study aimed to investigate the effects of high-yield crude polysaccharides from Cordyceps militaris (CMP) on high-fat diet (HFD) mice model and the gut microbiota community assembly, and to identify whether selenium (Se) addition would improve CMP action mode during cultivation. We found that the CMP treatment ameliorated adipose and liver pathologic morphology and fat accumulation in obese mice, while, SeCMP intervention was not superior than CMP in body mass gain, but notably decreasing serum triglyceride level increased by HFD. The upregulated expression of gene Cyp7a1 in liver and protein UCP1 in brown adipose tissue (BAT) preliminary indicated that the effect might relate to bile acids (BAs) metabolism pathway and thermogenesis. In addition, CMP showed a drastic decrease in the gut microbes which positively correlated with dyslipidemia parameters. Our result reveals the potential of CMP to be used as functional food in the prevention of diet-induced adipose and liver steatosis, so does SeCMP has outstanding capacity of improving dyslipidemia.

Emerging autologous cellular therapies that utilize platelet-rich plasma (PRP) applications have the potential to play adjunctive roles in a variety of regenerative medicine treatment plans. There is a global unmet need for tissue repair strategies to treat musculoskeletal (MSK) and spinal disorders, osteoarthritis (OA), and patients with chronic complex and recalcitrant wounds. PRP therapy is based on the fact that platelet growth factors (PGFs) support the three phases of wound healing and repair cascade (inflammation, proliferation, remodeling). Many different PRP formulations have been evaluated, originating from human, in vitro, and animal studies. However, recommendations from in vitro and animal research often lead to different clinical outcomes because it is difficult to translate non-clinical study outcomes and methodology recommendations to human clinical treatment protocols. In recent years, progress has been made in understanding PRP technology and the concepts for bioformulation, and new research directives and new indications have been suggested. In this review, we will discuss recent developments regarding PRP preparation and composition regarding platelet dosing, leukocyte activities concerning innate and adaptive immunomodulation, serotonin (5-HT) effects and pain killing. Furthermore, we discuss PRP mechanisms related to inflammation and angiogenesis in tissue repair and regenerative processes. Lastly, we will review the effect of certain drugs on PRP activity, and the combination of PRP and rehabilitation protocols.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

Autosomal dominant isolated foveal hypoplasia (FVH1) is a rare condition of foveal hypoplasia (FH) that lacks any other ocular manifestations. FVH1 is associated with hypomorphic mutations in the PAX6 gene. We report our findings in 17 patients with PAX6 mutations associated with FVH1 or FH with aniridia and corneal opacities. Patients with three mutations, p.V78E, p.V83F and p.R128H, in the C-terminal subdomain of the paired domain (CTS) consistently had severe FH. Luciferase assays indicated that the transcriptional activities of these mutations were significantly reduced comparable to that with truncation mutation of p.G65Rfs*5. Patients with p.P20S in the N-terminal subdomain of the paired domain, and a patient with p.N365K in the proline-serine-threonine-rich domain (PSTD) had mild FH. A patient with p.Q255L in the homeodomain had severe FH. The P20S and Q255L mutants did not affect the transcriptional activity. Mutant N365K had a retained DNA binding activity but a reduced transcriptional activity due to a low PSTD transactivation. These findings demonstrated that mutations associated with FVH1 underlie a functional divergence between DNA binding ability and transcriptional activity. Broadly distributed mutations in the PAX6 gene, not limited to the CST region, were responsible for FVH1.

The remaining capacity can only be measured with offline method. This brings great challenge for the online prediction of Li-ion battery’s RUL. A novel online prediction method for Li-ion battery’s RUL was proposed, which is based on multiple health indicators (HIs) and can be derived from the batteries’ historical operation data. Firstly, four indirect HIs were built according to the battery’s operation current, voltage and temperature data respectively. On that basis, a generalized regression neural network (GRNN) was developed to estimate the battery’s remaining capacity, and the non-linear autoregressive approach (NAR) was utilized to predict the battery’s RUL based on the estimated capacity value. Furthermore, to reduce the interference, twice wavelet denoising were performed with different thresholds. A case study is conducted with a NASA battery dataset to demonstrate the effectiveness of the method. The result shows that the proposed method can obtain Li-ion batteries’ RUL effectively.

SRC homology 3 (SH3) domains are critical interaction modules that orchestrate the assembly of protein complexes involved in diverse biological processes. They facilitate transient protein-protein interactions by selectively interacting with proline-rich motifs (PRMs). A database search revealed 298 SH3 domains in 221 human proteins. Multiple sequence alignment of human SH3 domains is useful for phylogenetic analysis and determination of their selectivity towards PRM-containing peptides (PRPs). However, a more precise functional classification of SH3 domains is achieved by constructing a phylogenetic tree only from PRM-binding residues and using existing SH3-PRP structures and biochemical data to determine the specificity within each of the 10 families for particular PRPs. In addition, the C-terminal proline-rich domain of the RAS activator SOS1 covers 13 of the 14 recognized proline-rich consensus sequence motifs, encompassing differential PRP pattern selectivity among all SH3 families. To evaluate binding capabilities and affinities, we conducted fluorescence dot blot and polarization experiments using 25 representative SH3 domains and various PRPs derived from SOS1. Our analysis has identified 45 interacting pairs with binding affinities ranging from 0.2 to 125 micromolar out of 300 tested and potential new interactors of SOS1. Furthermore, it establishes a framework to bridge the gap between SH3 and PRP interactions and provides predictive insights into potential interactions of SH3 domains with PRMs based on sequence specifications. This novel framework has the potential to enhance the understanding of protein networks mediated by SH3-PRM interactions and be utilized as a general approach for other domain-peptide interactions.

Triphenylphosphonium (TPP) derivatives of a decapeptide related to sequences of bactenecin 7 (Bac7) and oncocin (Onc112) were synthesized and studied as potential antimicrobial compounds using various biochemical and microbiological assays. It was shown that while the reduction of the Bac7 length to 10 a.a. residues dramatically decreases the affinity to bacterial ribosomes, the modification of peptide with alkyl-TPP moieties leads to an increase in the affinity. New analogs which structure combines a decapeptide related to Bac7 and Onc112 — Bac(1-10, R/Y) — and TPP, attached to the C-terminal amino acid residue through alkylamide linkers, inhibit translation in vitro and are found to be more selective inhibitors of bacterial translation as compared with eukaryotic translation, than Onc112 and Bac7. Triphenylphosphonium analogs of a decapeptide related to Bac7 and Onc112 suppress the growth of both gram-negative bacteria, similar to Onc112 and Bac7, and gram-positive ones as alkyl-TPP derivatives, and also act against some resistant laboratory strains. Bac(1-10, R/Y)-C2-TPP, containing a short alkylamide linker between the decapeptide and TPP, is transferred into the E. coli cells via the SbmA transporter protein. TPP derivatives of the decapeptide Bac(1-10, R/Y) containing either decylamide or ethylamide linker cause B. subtilis membrane depolarization, similar to alkyl-TPP. The Bac(1-10, R/Y)-C2-TPP analog is proved to be non-toxic for mammalian cells by MTT-test.

Tissue regeneration is an essential requirement for wound healing and recovery of organs’ dysfunction. It has been demonstrated that wound healing can be facilitated by activating paracrine signaling mediated by exosomes secreted from stem cells, since exosomes deliver many functional molecules including growth factors (GFs) and neurotrophic factors (NFs) effective for tissue regeneration. In this study, an exosome-rich conditioned medium (ERCM) was collected from human amniotic membrane stem cells (AMSCs) by cultivating the cells under a low oxygen tension (2% O2 and 5% CO2). The contents of GFs and NFs including keratinocyte growth factor, epidermal growth factor, fibroblast growth factor 1, transforming growth factor-β, and vascular endothelial growth factor responsible for skin regeneration were much higher (10-30 folds) in the ERCM than in normal conditioned medium. In was found that CM-DiI-labeled exosomes readily entered keratinocytes and fibroblasts, and that ERCM not only facilitated the proliferation of keratinocytes in normal condition, but also protected against H2O2 cytotoxicity in a concentration-dependent manner. In cell-migration assay, the scratch wound in keratinocyte culture dish was rapidly closed by treatment with ERCM. Such wound-healing effects of ERCM were confirmed in a rat whole skin-excision model: i.e., the wound closure was significantly accelerated by topical application of ERCM solution (4 x 109 exosome particles/100 μL) at 4-day intervals. In the wounded skin, the deposition of collagens was enhanced by treatment with ERCM, which was supported by the increased production of collagen-1 and collagen-3. The results indicate that ERCM from AMSCs containing a large amount of GFs and NFs improve wound healing through tissue regeneration not only by facilitating keratinocyte proliferation for skin repair, but also activating fibroblasts for extracellular matrix production.

Tissue regeneration is an essential requirement for wound healing and recovery of organs’ function. It has been demonstrated that wound healing can be facilitated by activating paracrine signaling mediated by exosomes secreted from stem cells, since exosomes deliver many functional molecules including growth factors (GFs) and neurotrophic factors (NFs) effective for tissue regeneration. In this study, an exosome-rich conditioned medium (ERCM) was collected from human amniotic membrane stem cells (AMSCs) by cultivating the cells under a low oxygen tension (2% O2 and 5% CO2). The contents of GFs and NFs including keratinocyte growth factor, epidermal growth factor, fibroblast growth factor 1, transforming growth factor-β, and vascular endothelial growth factor responsible for skin regeneration were much higher (10-30 folds) in the ERCM than in normal conditioned medium (NCM). In was found that CM-DiI-labeled exosomes readily entered keratinocytes and fibroblasts, and that ERCM not only facilitated the proliferation of keratinocytes in normal condition, but also protected against H2O2 cytotoxicity. In cell-migration assay, the scratch wound in keratinocyte culture dish was rapidly closed by treatment with ERCM. Such wound-healing effects of ERCM were confirmed in a rat whole skin-excision model: i.e., the wound closure was significantly accelerated, remaining minimal crusts, by topical application of ERCM solution (4 x 109 exosome particles/100 μL) at 4-day intervals. In the wounded skin, the deposition of collagens was enhanced by treatment with ERCM, which was supported by the increased production of collagen-1 and collagen-3. In addition, enhanced angiogenesis in ERCM-treated wounds was confirmed by increased von Willebrand factor (vWF)-positive endothelial cells. The results indicate that ERCM from AMSCs with high concentrations of GFs and NFs improves wound healing through tissue regeneration not only by facilitating keratinocyte proliferation for skin repair, but also activating fibroblasts for extracellular matrix production, in addition to the regulation of angiogenesis and scar tissue formation.

Alveolar bone atrophy after tooth extraction presents significant difficulties when planning delayed-immediate implant treatment to replace a lost tooth. Socket augmentation is an effective therapy that limits the post extraction volumetric changes and facilitates implant placement whilst reducing the need for staged grafting. However, socket augmentation and osteoconductive graft conversion is a slow process that could take 4-6 months. PRF and its variants have significant bio-enhancement effect on wound healing and regeneration through release of platelet drived growth factors, bioactive substances, cytokines. Leukocytes in PRF also play a significant role in enhancing tissue regeneration as part of osteo-immune response. Use of PRF during socket augmentation is highly effective in enhancing extraction site healing and graft integration by angiogenesis, cell proliferation, recruitment, and differentiation through release of growth factors and bioactive substances mediated by platelets and leukocytes. PRF with SA is recommended as an adjunct to SA as a sole biomaterial or in combination with xenograft or allograft bone substitutes to enhance tissue regeneration and to reduce risk of infection, osteitis and postoperative pain in extraction sockets

Most authors have investigated the role of mannoproteins on wine quality but very few analyze the use of grape derived polysaccharides as they are not commercially available. Purified grape derived polysaccharides from red wine (WPP) and winemaking by-products (DWRP: Distilled Washing Residues Polysaccharides) were used as potential fining agents to modulate white wine flavour. Phenolics and volatile compounds were analyzed in control and wines treated with WPP, DWRP and commercial mannoproteins (CM) after one and twelve months of bottling, and a sensory analysis was conducted. WPP and DWRP, rich in rhamnogalacturonans-II, showed as good modulators of wine aroma and astringency. Improvement of wine aroma was related to an increase of all volatile families expect higher alcohols and volatile acids. The modulation of astringency and bitterness was related to a reduction in the proanthocyanidin content and its mean degree of polymerization. Extracts with polysaccharides with higher protein contents presented higher retention of volatile compounds, and DWRP extract showed more positive effects on the overall aroma. Our novel results open the possibility of obtaining valuable polysaccharides from distilled washing residues of wine-pomaces, which could promote its valorization as by-product. This is the first time to describe the potential use of this by-product.

Malaria is a prevalent disease in several tropical and subtropical regions, including Brazil, where remains a significant public health concern. Despite control efforts, reintroduction of endemics in areas without cases for decades poses a challenge. To assess factors influencing ma-laria risk, regional outbreak cluster analysis and a spatio-temporal models were developed for the Brazilian Amazon, incorporating climate, land use/cover interactions, endemic bird, and amphibian richness. Results showed that amphibian, bird richness and endemism correlated with a reduction in malaria risk. Presence of forest had a positive effect on risk, but it depended on its juxtaposition with anthropic land uses. Biodiversity and landscape composition, rather than forest formation presence alone, modulated malaria risk in the period. Areas with low en-demic species diversity and high human activity, predominantly anthropogenic landscapes posed high malaria risk. This study underscores the importance of considering the broader eco-logical context in malaria control efforts.

Formation of Fe- and Mg-rich smectite and zeolite under alkaline conditions is concerned as secondary minerals after alkaline alteration of bentonite in a repository of radioactive wastes. It might be crucial for safety assessment whether smectite will be formed or not as secondary minerals after alkaline alteration of bentonite. In present paper, Fe- and Mg-rich smectite which are currently interacting with hyperalkaline groundwater was found at Narra in Palawan, Philippines. Mineralogical and geochemical investigation was conducted to understand formation process of smectite and factors determined secondary mineral species. Our study revealed a certain amount of smectite may have been produced under hyperalkaline conditions, altered from amorphous or poorly crystalline material such as M-S-H and F-S-H. Key factor which decides smectite or zeolite as secondary minerals after alkaline alteration of bentonite might be whether nuclei of M-S-H and/or F-S-H will be formed or not. This might be decided by the presence of dissolved Mg2+ and Fe2+ in the system. Our suggested formation process of smectite under alkaline conditions is analogue with generally-accepted model of smectite formation that might have been occurred on early Mars.

Coffee processing generates a huge amount of waste which contains many natural products. Here, we report the discovery of a panel novel cell-penetrating and metal-ion binding microproteins designated coffeetide cC1a-c and cL1-6 from the husk of two popular coffee plants, Coffea canephora and Coffea liberica, respectively. Combining sequence determination and database search, we showed that the prototypic coffeetide cC1a is a 37-residue, eight-cysteine microprotein with a hevein-like cysteine motif but without a chitin-binding domain. NMR determination of cC1a revealed a compact structure that confers it resistance to heat and proteolytic degradation. Disulfide mapping together with chemical synthesis revealed that cC1a has a ginsentide-like, and not a hevein-like, disulfide connectivity. In addition, transcriptomic analysis showed that the 98-residue micrcoproten-like coffeetide precursor contains a three-domain arrangement like ginsentide precursors. Molecular modeling together with experimental validation revealed a Mg2+ and Fe3+ binding pocket at the N-terminus formed by three glutamic acids. Importantly, cC1a is amphipathic with a continuous stretch of 19 apolar amino acids, and which enables its cell penetration to target intracellular proteins, despite being highly negatively charged. Our findings suggest that coffee by-products could provide a source of ginsentide-like bioactive peptides that have potential to target intracellular proteins.