Among the various methods for collecting oil spills and oil products, including from the water surface, one of the most effective is the use of sorbents. In this work, three-component bio-based composite granular adsorbents were produced and studied for oil products pollution collection. A bio-based binder made of peat, devulcanised crumb rubber from used tyres, and part fly ash as cenospheres were used for absorbent production. The structure, surface morphology, porosity, mechanical properties, and sorption kinetics of the obtained samples were studied. Composite hydrophobicity and sorption capacity to oil products such as diesel fuel (DF) and motor oil (MO) were determined. The obtained pellets are characterised by a sufficiently pronounced ability to absorb oil products such as DF. As the amount of CR in the granules increases, the diesel absorption capacity increases significantly. The case of 30-70-0 is almost 3 times higher than the granules from homogenised peat. The increase in q is due to two factors: pronounced surface hydrophobicity of the samples (Θ = 152°) and a heterogeneous porous granule structure. The presence of the cenosphere in the biocomposite reduces its surface hydrophobicity while increasing the diesel absorption capacity. Relatively rapid realisation of the maximum saturation by the MO was noted. In common, the designed absorbent shows up to 0.7 g·g^-1 sorption capacity for MO and up to 1.55 g·g^-1 sorption capacity for diesel. A possible mechanism of DF absorption and the limiting stages of the process approximated for different kinetic models are discussed. The Weber-Morris diffusion model is used to primarily distinguish the limiting effect of external and internal diffusion of adsorbate on the absorption process

The present review is dedicated to using of peat on the example of fen peat in high added-value products and applications. Mainly, but not limited, last decade literature was analysed from the perspective of innovation potential of peat applications in environmental technologies on examples of studies from the Baltic Sea region. Paper covers a wide range of applications of peat products started from agriculture to medicine and cosmetics. A separate chapter is devoted to the deep-processed peat product - humic substances (humate, humic and fulvic salts and acids). Generalised dependence of product extraction rate and its properties, depending on the process parameters are provided. Widely are described applications of the humic sub-stance applications covering economic aspects, such as production costs. In the last chapter of the review are given recommendations for applications considering the most recent trends of peat-based product developments. This accumulated information could be useful for future production, development of new, environmentally friendly products and start-ups establishment.

The utilisation of the industrial residual products to develop new value-added materials and to reduce footprint is one of the critical challenges of science and industry. Development of the new multifunctional and bio-based composites materials is an excellent opportunity for the effective utilisation of industrial residual products. Keeping the different issues in mind, in this work, we describe the manufacturing and characterisation of the three-phases bio-based composites. The key components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash, i.e. the cenosphere (CS). The three-phase composite prepared in the form of a block were investigated for their mechanical properties and density. The three-phase composite was prepared in the form a) of a block were investigated for their mechanical properties, and density and b) a form of granules for determination of the water and oil products sorption were investigated. We have also investigated the dependence of the properties on the DCR and CS fraction. It has been found, that maximum compression strength (in block form) observed for composition without CS and DCR addition was- 79.3 MPa, while the second-highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt%, the compression strength is in the range from 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.