Al-Zn-Mg-Cu alloy has high specific strength, good corrosion resistance, fracture toughness and fatigue resistance. It is one of the most important structural materials in the fields of aviation, aerospace, weapons, transportation and so on, which plays a huge role in the field of aerospace.In order to optimize the strength, toughness and corrosion properties of Al-Zn-Mg-Cu alloy, alloying has always been the focus of research on Al-Zn-Mg-Cu alloy. The effects of main alloying elements, trace alloying elements and rare earth elements on the microstructure and properties of Al-Zn-Mg-Cu aluminum alloy were briefly introduced in the paper, and the future research directions were prospected.

The cast grains of the 7055 aluminum alloy were refined by adding Sm + Er, and the proper heat treatment procedure was utilized to further precipitate the rare earth phase in order to increase the alloy's strength and toughness. The grain size, microstructure and phase were characterized by optical microscopes (OM), Scanning electron microscopy - energy spectrum (SEM-EDS), XRD diffractometer (XRD). The macroscopic hardness, yield strength and tensile strength of alloy materials were measured by hardness meter and universal electronic tensile machine. The results shown that the as-cast sample and the heat treatment sample all exist Al10Cu7Sm2 and Al8Cu4Er rare earth phase; But after heat treatment, the volume percentage of the rare earth phase dramatically increased and the dispersion was more unified. When 0.3wt.%Sm and 0.1wt.%Er were added, the grain size could be refined to 53μm. With the increase of the total content of rare earth elements, the refining effect first increased and then decreased. Under 410 oC solid solution for 2h + 150oC aging for 12h, the macroscopic hardness, yield strength, tensile strength and elongation of 0.3wt.%Sm + 0.1wt.%Er+7055 as-cast sample were 155.8HV, 620.5Mpa, 658.1Mpa, and 11.90%, respectively.

In order to solve the problem of environmental pollution caused by a large number of discarded hickory husks in Lin'an, and to make them a clean energy source that can be recycled, in this paper,using crushed hickory husks as raw material, single factor test was carried out on a hydraulic plunger forming machine with different moisture content and length-diameter ratio of forming sleeve.The change of axial pressure and radial force in the forming sleeve is measured by the sensor, and the microstructure of the biomass moulding fuel briquette was observed by stereomicroscope. The results showed that the hickory husks could be compressed and formed at room temperature. When the moisture content of the hickory husks is 14% and the length-diameter ratio of the forming sleeve is 4.5, the forming quality is the best, and the relaxation density of the formed briquette is up to 0.98g /cm3. When the moisture` content is the same, the forming pressure increases with the increase of the length-diameter ratio of the forming sleeve. When the length-diameter ratio of molding sleeve is the same, the molding pressure increases first and then decreases with the increase of water content.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

Hepatitis E virus (HEV) is a common cause of acute hepatitis worldwide, accounting for approximately 25% of deaths among pregnant women. We previously reported that pregnancy serum facilitates HEV replication in vitro. However, the differences in host cells with HEV infection induced by pregnancy serum and fetal bovine serum (FBS) are unclear. In this study, differentially expressed proteins were identified in HEV-infected hepatoma cells (HepG2) supplemented with different sera by using isobaric tags for relative and absolute quantitation. Proteomic analysis indicated that HEV infection significantly induced 1014 differentially expressed proteins in HEV-infected HepG2 cells when supplemented with FBS compared with pregnancy serum. Further validation by Western blot confirmed that filamin A, heat-shock proteins 70 and 90, Cytochrome c, and Thioredoxin were associated with HEV infection. This comparative analysis provides an important basis to further investigate HEV pathogenesis in pregnant women and HEV replication.