This paper, the second in a series of two, describes the experimental results for removing arsenic from the dust collected in the electrostatic precipitators of a fluidized bed roasting oven (RP dust). The RP dust produced is discharged as a toxic waste, although its copper content is close to 20% by weight. This work aims to process the RP dust; until obtained a material with a low concentration of arsenic, which could be recirculated in smelting operations and recover the valuable metals. Based on the successful experience obtained in the first document with FS dust, this work proposes to use the reduction-sulphidation-volatilization processes to carry out the volatilization of arsenic from RP dust. A set of experiments was realized in the roasting different ratios of the mixture of copper concentrate / RP dust, sulfur / RP dust varying temperature and roasting time; to reach an arsenic concentration <0.5% by weight. The RP dust was characterized using different techniques, that confirmed more than 20% by weight of copper and describing its structure as a small particle agglomerate (<5 µm), with a complex sulfoxide morphology. The main results indicated: that for a 75/25 mixture of the copper concentrate / PR dust under 700 ° C, 15 minutes roasting time with air atmosphere, the arsenic volatilization was 96% by weight. Meanwhile, for a 5/95 mixture of sulfur / RP dust, at 650 ° C, the volatilization of arsenic was 67% by weight.

This paper (the first of a series of two) seeks to describe the experimental results of removing arsenic from dust collected in electrostatic precipitators of copper into the pyro-metallurgy gas cleaning systems. The first work corresponds to the treatment of dust contained in gas off generated in the copper Flash Smelting Furnace process (FS dust), while the second focuses on the treatment of dust generated from a Fluidized Bed Roasting Furnace (RP dust). The dust is complex sulphur-oxide-metals with concentrations of copper above 10 wt % and relatively high concentrations of silver. Due to the dust has an arsenic’s concentration above 5 wt %, makes it difficult to recover valuable metals through hydro-metallurgical processes or by direct recirculation of the dust into a smelting furnace. Thus, the development of pyrometallurgical processes aimed to reduce the concentration of arsenic in dust is the main purpose of this study, particularly the production of a material suitable for recirculation in smelting operations. The works conducted provide a detailed characterization of the dust, including Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN), Scanning electron microscope-Energy Dispersive X-ray analysis (SEM/EDS), X-ray diffraction (XR-D), elemental chemical analysis using Atomic Adsorption (A. A.) and X-Ray Fluorescence (X-RF). By considering that arsenic volatilization requires a process of reduction-sulphidation-volatilization, the works explore the roasting of mixtures of copper concentrate/dust, sulphur/dust and pyrrhotite/dust. The degree of volatilization was determined by elemental chemical analysis of arsenic in the mixture after and before the roasting process. The results indicated the effect of parameters such as temperature, gas flow, gas composition and the ratio of mixtures (concentrate, sulphur or pyrrhotite)/dust on the volatilization of arsenic. The findings indicate that the concentration of arsenic in the FS dust can be reduced to a relatively low level (<0.5 wt %), allowing to the material to be recirculated into smelting processes.

Since the requirements in terms of power of the electronic applications range wide, the developed Energy Harvesting (EH) systems limit their availability to the less power demanding applications. However, this paper focuses on increasing the energy levels collected in the EH system so that it can be included in more demanding applications in terms of power. Therefore, an electronic system capable of grouping many single harvesting channels into one single system is analyzed in this paper. This multi-harvester electronic system is able to manage efficiently the energy collected by multiple vibratory transducers. The paper includes a comparison of its performance against some of the State-of-the-Art EH energy management circuits that interface the transducers. The method employed to demonstrate the intrinsic efficiency of each of the electronic circuits tested was based on experimental tests, where the average power transferred from several identical and simultaneous electric sources to a single storage element was measured. It was found out that only one energy management circuit was able to increase the transferred energy in a linear way while new input electric sources were added.

This work presents the design, construction and performance evaluation of a photovoltaic greenhouse as an energy hub (EH) in modern agriculture that integrates battery energy storage (BES) and an electric vehicle charging station (EV). The greenhouse is composed of 48 semi-transparent PV panels with nominal transparency of 20% and 110 W capacity. The control of the PV greenhouse as EH was approached as an optimization problem with the aim of minimizing the cost of the energy used from the grid. Simulation results indicate that the integrated BES is capable of balancing power transactions within the microgrid. In addition, it was found that the case of slow charging of the EV at night was less demanding on the BES than fast charging during the day in terms of abrupt power transitions and average depletion of BES SOC (61% vs 53%). Empirical results also demonstrated the negative impact of dust generated by agricultural activity on the performance of solar panels. For a period analyzed of three years, an average yearly production loss of 6.8% was calculated.