In this paper, we present a preliminary study and conceptual idea concerning 3D printing water-sensitive glass by exemplifying with a borosilicate glass with high alkali and alkaline oxide contents using direct ink writing. The investigated material was prepared in the form of a glass frit, which was further ground in order to obtain a fine powder of desired particle size distribution. In a following step, inks were prepared by mixing the fine glass powder with Pluoronic F-127 hydrogel. The acquired pastes were rheologically characterized and printed using a Robocasting device. DSC experiments were performed for base materials and the obtained green bodies. After sintering, SEM and XRD analyses were carried out in order to examine microstructure and the eventual presence of crystalline phase inclusions. Results confirmed that obtained inks exhibit stable rheological properties despite the propensity of glass to undergo hydrolysis and could be adjusted to desirable values for 3D printing. No additional phase was observed, supporting the suitability of the designed technology for the production of water sensitive glass inks. SEM micrographs of the sintered samples revealed the presence of closed porosity, which may be the main reason of light scattering.

Biomedical aspects of tattooing have been extensively discussed in literature, however pathophysiological effects of tattoo inks in the human body are still unexplored. Oxidative stress is considered responsible for the adverse effects of tattooing, however no experimental evidence for tattoo ink-related oxidative stress in the human body currently exists. The aim was to examine the effect of a blue tattoo on skin redox regulatory network (RRN) parameters in a single human subject. Skin surface oxidation-reduction potential (ORP) was analyzed with a PH60F flat probe. Interstitial and intracellular fluid enriched capillary blood from the tattoo and the control area was extracted and analyzed with I₂/KI-stabilized microORP, nitrocellulose redox permanganometry (NRP), carbonato-cobaltate (III) formation-derived H₂O₂ dissociation rate assay, 1,2,3-trihydroxybenzene autoxidation assay, thiobarbituric reactive substances (TBARS) assay and 5,5,’-dithio-bis-(2-nitrobenzoic acid) (DTNB)-based determination of free thiol content in low molecular weight and protein precipitate fractions. Surface ORP analysis revealed a greater antioxidant capacity of tattooed skin in comparison with the control (CTR). Capillary blood analysis confirmed greater reductive capacity in the tattoo sample both by microORP (-4.33mV vs CTR) and NRP (+10.8%). Hydrogen peroxide dissociation rate (+11.8%), and protein sulfhydryl content (+8.5%) were increased, and lipid peroxidation (-15%) was reduced in the tattoo sample in comparison with the CTR. In this N-of-1 study, RRN of tattooed skin was shifted towards a more reductive state with all parameters indicating reduced levels of oxidative stress in comparison with nontattooed skin. The local antioxidant effect of copper(II) phthalocyanine provides one possible explanation of the observed effects.

Bismaleimide (BMI) is a high-performance thermosetting resin widely used in the aerospace, automotive, and mechanical and electronics industries due to its chemical and mechanical stability. It also has the capability of being used as an ink in polyjets used for 3D printing evident from thinner mellamide FTIR bands and faster curing rates as observed from TGA-DSC studies.

In document forensic, Ink mismatch relays very important information about forgeries in this way we can find out the authenticity of documents. Finding out and distinguishing these unique inks from the multispectral document is very challenging task. In this paper we proposed the method to identify the inks using clustering. We used K-Mean clustering instead of widely known Fuzzy C-Means Clustering (FCM) and successfully identity the number of inks. For the purpose of optimizing and improving our results we used two optimization techniques such as Elbow and silhouette optimization techniques.

Nanocelluloses have gained significant attention in recent years due to singular properties (good biocompatibility, high optical transparency and mechanical strength, large specific surface area and good film-forming ability) and wide-ranging applications (paper, food packaging, textiles, electronics and biomedical). This article is a comprehensive review of nanocelluloses from the preparation methods to their applications in conservation and restoration of historical paper documents. The novelty lies in the information collected about nanocelluloses as renewable, environmentally friendly and sustainable materials in the field of preservation of cultural heritage as an alternative to conventional methods. Several studies have demonstrated that nanocelluloses, with or without other particles, impart to the paper documents excellent optical and mechanical properties, very good stability against temperature and humidity aging, stronger antibacterial and antifungal activity, high protection to UV light and do not require additional adhesive.

Copper(I) sulfide (Cu2S) is a low-cost, earth-abundant, and non-toxic thermoelectric material for applications in the middle-high temperature range (>650 K). Although 3D printing these materials can simplify their manufacturing, elevated temperatures observed during sintering impair their crystal structure and energy conversion efficiency. In this study, we demonstrated a novel post-processing methodology to revert the thermoelectric properties of the 3D printed Cu2-xS materials back to the unimpaired state via sulfur infusion. After printing and sintering, sulfur was infused into the specimens under vacuum to optimize their crystal structure and achieve high thermoelectric efficiency. Chemical analysis and X-ray Diffraction (XRD) tests showed that after the sulfur infusion process, the Cu/S ratio was reverted close to the stoichiometric level. 3D printed Cu2-xS showed p-type thermoelectric behavior with electrical conductivity peaking at 143 S-cm-1 at 750 K and Seebeck coefficient of 175 µV-K-1 at 627 K. Figure of merit (ZT) value of 1.0 at 780 K was achieved which is the highest value ever reported for a 3D printed Cu2-xS thermoelectrics at this temperature. Fabrication of environmentally friendly thermoelectric materials with extended dimensional freedom and conversion efficiency has the potential to impact the thermoelectric industry with new energy conversion applications and lowered manufacturing costs.

Digital microfluidics (DMF) devices enable precise manipulation of small liquid volumes in point-of-care testing. Printed circuit board (PCB) substrate is commonly utilized to build DMF devices. However, inkjet printing can be used to fabricate DMF circuits, providing a less expensive alternative to PCB-based DMF designs while enabling more rapid design iteration cycles. We demonstrate the fabrication process of the inkjet-printed DMF circuit. We compare Kapton and polymethyl methacrylate (PMMA) as dielectric coatings by measuring the minimal droplet actuation voltage for a range of actuation frequencies. The minimum actuation voltage of 5.6 V was required for droplet movement with the PMMA layer thickness of 0.2 μm and a hydrophobic layer of 0.17 μm. Significant issues with PMMA dielectric breakdown were observed at actuation voltages above 10 V. In comparison, devices that utilized Kapton were found to be more robust even at the actuation voltage up to 100 V.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behaviour were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

Laser-induced breakdown spectroscopy (LIBS) is an important analysis technique with applications in many industrial branches and fields of scientific research. Nowadays, the advantages of LIBS are impaired by the main drawback in the analysis of collected data. This procedure is essentially based on the comparison of lines present in the spectrum with a literature database. This paper proposes the use of various computational intelligence methods to develop a reliable and fast classification of non-destructively acquired LIBS spectra into a set of predefined classes. We focus on a specific problem of classification of paper-ink samples into 30 separate, predefined classes. For each of 30 classes (10 pens of each of 5 ink types combined with 10 sheets of 5 paper types plus empty pages) 100 LIBS spectra are collected. Four variants of preprocessing, seven classifiers (Decision trees, Random forest, k-Nearest Neighbour, Support Vector Machine, Probabilistic Neural Network, Multi-Layer Perceptron, and Generalized Regression Neural Network), 5-fold stratified cross-validation and test on an independent set (for methods evaluation) scenarios are employed. Our developed system yielded an accuracy of 99.08% with average classification time of about 0.12 s is obtained using the random forest classifier. Our results clearly demonstrates that machine learning methods can be used to identify the paper-ink samples based on LIBS reliably at a faster rate.

Among cephalopod discards, ink has revealed several beneficial properties regarding human health, environmental preservation and food preservation. In this study, different concentrations of an aqueous extract of cuttlefish (Sepia spp.) ink (CI) were added, respectively, to the packing medium employed during golden seabream (Sparus aurata) canning. Quality parameters of the resulting canned fish were determined and compared to the counterpart control and raw samples. As a result, an important effect of the CI concentration added to the packing medium was proved. The presence in the packing medium of a relatively low CI concentration led to lower (p<0.05) lipid oxidation development (fluorescent compound formation), lower (p<0.05) changes of colour parameters (L* and a* values) and lower (p<0.05) trimethylamine values in canned fish. Additionally, the two lowest CI concentrations tested led to higher average values of C22:6ω3 and ω3/ω6 ratios. Remarkably, higher average values of free fatty acids, polyene index and C20:5ω3 were detected in all kinds of CI-treated fish when compared to control canned samples. In agreement with environmental sustainability and circular economy requirements, the study provides a first approach to a novel and beneficial use of the present marine discard for the quality enhancement of canned fish.

Forensic document examiners can determine the authenticity of questioned documents by analyzing the ink used to create them. If an ink mismatch is found, it could be a sign of scam, backdating, or forgery. In this research a Hyperspectral Images of iVision HHID dataset is used to detect number of possible inks used in document. By using Hyperspectral Images, it’s possible to detect ink mismatch in a given document. In this research unsupervised learning method K-means is used to detect number of inks. Approximate number of clusters are determined by Elbow and Silhouette method before implementation of K-means.

A novel solution-processed graphene-based material was synthesized by treating graphene oxide (GO) with 2,5,7-trinitro-9-oxo-fluorenone-4-carboxylic acid (TNF-COOH) moieties, via simple synthetic routes. The yielded molecule N-[(carbamoyl-GO)ethyl]-N’-[(carbamoyl)-(2,5,7-trinitro-9-oxo-fluorene)] (GO-TNF) was thoroughly characterized and it was shown that it presents favorable highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels to function as a bridge component between the polymeric donor poly({4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl}{3-fluoro-2-[(2-ethylhexyl)carbonyl] thieno[3,4-b]thiophenediyl}) (PTB7) and the fullerene derivative acceptor [6,6]-phenyl-C₇₁-butyric-acid-methylester (PC₇₁BM). In this context, a GO-TNF based ink was prepared and directly incorporated within the binary photoactive layer, in different volume ratios (1-3% ratio to the blend), for the effective realization of inverted ternary organic solar cells (OSCs) of the structure ITO/PFN/PTB7:GO-TNF:PC₇₁BM/MoO₃/Al. The addition of 2% v/v GO-TNF ink led to a champion power conversion efficiency (PCE) of 8.71% that was enhanced by ~13% as compared to the reference cell.

The utilization of eco-fonts for office printing is a sustainable, “green” printing concept, which has obvious economic benefits. As a result, it has a significant effect on environmental sustainability. This practice's fundamental problem is the decreased quality of text printed using eco-fonts compared to those printed with regular fonts. The aim of this research is eco-font efficiency estimation, i.e. determination of toner usage reduction level of inkjet-printed documents typed with this font type, as well as estimation of the extent humans perceive differences between text printed with eco-font and the one printed by its “non-eco“ equivalent. Combining the instrumental measuring method and digital image analysis, it was found that this simple principle (eco-font utilization) enables substantial toner usage reduction for an inkjet printing system. At the same time, a visual test showed that the visual experience of text printed using eco-font was sufficient. In addition, awareness of the benefits that eco-font utilization brings, change users’ attitude towards eco-font quality. The concept of removing the black pixel from this commonly used Thai font has a great potential for the sustainability printing process, and this simple solution could be applied to other languages as part of the GIT campaign.

Hydroiodic acid (HI) treated - reduced graphene oxide (rGO) ink/conductive polymeric composites are considered as promising cold cathodes in terms of high geometrical aspect ratio and low field emission (FE) threshold devices. In this study, four simple, cost-effective, solution-processed approaches for rGO-based field effect emitters were developed, optimized and compared; rGO layers were coated on a) n+ doped Si substrate, b) n⁺-Si/P3HT:rGO, c) n⁺-Si/PCDTBT:rGO and d) n⁺-Si/PCDTBT:PC₇₁BM:rGO composites, respectively. The fabricated emitters were optimized by tailoring the concentration ratios of their preparation and field emission characteristics. In a critical composite ratio, FE performance was remarkably improved compared to the pristine Si, as well as n⁺-Si/rGO field emitter. In this context, the impact of various materials, such as polymers, fullerene derivatives, as well as different solvents on rGO function reinforcement and consequently on FE performance upon rGO-based composites preparation was investigated. The field emitter consisted of n⁺-Si/PCDTBT:PC₇₁BM(80%):rGO(20%)/rGO displayed a field enhancement factor of ∼2850, with remarkable stability over 20h and low turn-on field in 0.6V/μm. High-efficiency graphene-based FE devices realization paves the way towards low-cost, large-scale electron sources development. Finally, the contribution of this hierarchical, composite film morphology was evaluated and discussed.

Hyper spectral imaging (HSI) is a technique that is used to obtain the spectrum for each pixel in the image. It helps in finding objects and identifying materials etc. Such an identification is very difficult using other imaging techniques. It allows the researchers to investigate the documents without any physical contact. Nowadays detection of unequal Ink mismatch based on HSI has shown vast improvement in distinguishing the inks. Detection of unequal Ink mismatch is an unbalanced clustering problem. This paper used K-means Clustering for ink mismatch detection. K-means Clustering find same subgroups in the data based on Euclidean distance. This paper demonstrates performance in unequal Ink mismatch based on HSI.

This paper discusses a cross-disciplinary, international collaboration aimed at researching a series of 15th century choir books at the abbey of San Giorgio Maggiore on the homonymous island in Venice. Produced for the abbey itself, the books have never left the island during their 500-years history, thereby allowing a unique opportunity to analyse historic artefacts, which have undergone little modification over time. Prompted by ongoing cataloguing work on the manuscripts, a week-long analytical campaign using a combination of non-invasive analytical methods used in portable configuration allowed the comprehensive characterisation of ten volumes. The manuscripts’ palette and painting techniques were analysed using near-infrared imaging, reflectance spectroscopy in the UV-vis-NIR range, Raman spectroscopy, X-ray fluorescence mapping and digital microscopy. The paper will discuss the challenges linked to the fragility and the large dimensions of the volumes as well as the most interesting results of the investigation. These include the detection of unusual painting materials such as bismuth ink, as well as the discovery of a less homogeneous palette than originally expected, which prompted a partial revision of the attribution of the decoration in one of the volumes to a single artist.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.