Thin-wall heat pipe is an efficient heat transfer component, which has been widely used in the field of heat dissipation of high-power electronic equipment in recent years. In this study, the orange peel morphology defect of thin-wall heat pipes after bending deformation was analyzed both for the macro 3D profile and for the micro-formation mechanism. The results show that after high temperature sintering treatment, the matrix grains of heat pipe are coarsened seriously and formed a strong Goss texture, while a certain annealing twins with the unique Copper orientation are retained. The distribution of Schmid factor value subjected to the uniaxial stress indicate the inhomogeneity of intergranular deformation exist among the annealing twins and matrix grains. The annealing twin exhibit a “hard-oriented” component during the deformation; thus, it plays a role as barrier and hinder the slipping of dislocation. As the strain accumulates, part of the annealing twins may protrude from the surface of heat pipe, forming a large-scale fluctuation of the surface as the so called the “orange peel” morphology. The 3D profile shows the bulged twins mostly perpendicular to the drawing direction, with about 200-300μm in width and 10-20μm in height.

A full connected world is expected to gain in the 6th generation mobile network (6G). As a typi-cal fully connected scenario, the internet of vehicle (IoV) enables intelligent vehicle operations via artificial intelligence (AI) and edge computing technologies. In the future of vehicular net-works, wide variety of services need powerful computing resources and higher quality of ser-vice (QoS). Existing resources are insufficient to match these requirements. Aim to this problem, An intelligent service offloading framework is provided. Based on the framework, an Algorithm of Improved Gradient Descent (AIGD) is created to accelerate the speed of iteration. So, the con-vergence of convolutional neural network (CNN) based on AIGD is able to be accelerated too. Then, an Algorithm of convolutional long short-term memory (CN_LSTM) Based Traffic Predic-tion (ACLBTP) is designed to gain the predicted number of vehicles belonged to the edge node. At last, an Algorithm of Service Offloading Based on CN_LSTM (ASOBCL) is conducted to of-fload these services to the vehicles belonged to the edge node. In ASOBCL, sorting technique is adopted to speed up the offloading work. Simulation results demonstrate the fact that the pre-diction strategy designed in this paper has high accuracy. The low offloading time and main-taining stable load balance is gained via running ASOBCL. Low offloading time means short response time. And, the QoS is guaranteed. So, these strategies designed in this paper are effec-tive and valuable.

Tryptanthrin has not been widely applied in clinical practice due to its poor solubility and low bioavailability in spite of possessing several biological and pharmacological activities. Here, to improve the solubility of tryptanthrin, two types of novel tryptanthrin-loaded micelles were prepared. One was tryptanthrin physically encapsulated by distearoyl phosphatidylethanolamine polyethylene glycol (DSPE-PEG) and the other was pegylated tryptanthrin synthesized by acid-sensitive hydrazone bond and further prepared as micelles. Molecular imprinting technology was used to separate pegylated tryptanthrin and free mPEG-COOH in the preparation of PEGylated tryptanthrin micelles with considerably high separation efficiency. The solubility of tryptanthrin-loaded DSPE-PEG micelles (TDMs) and PEGylated tryptanthrin micelles (PTMs) was increased by 300 and 1493 fold compared with that of tryptanthrin, respectively. The PTMs increased the solubility of tryptanthrin more effectively and 95% of tryptanthrin was released from PTMs at pH 5.5 in 12 h. The cytotoxicity of PTMs decreased under physiological conditions compared with that of tryptanthrin, whereas at pH 5.5, the PTMs showed comparable cytotoxicity with that of tryptanthrin, indicating successful drug release from the carrier in response to tumor cell pH. Overall, we elucidated an efficient method to improve water solubility of tryptanthrin and indicated pegylated tryptanthrin is a promising prodrug.

Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

With the unceasing advancement in wide-bandgap (WBG) semiconductor technology, the minimal reverse-recovery charge Qrr and other more powerful natures of WBG transistors enable totem-pole bridgeless PFC to become a dominant solution for energy storage systems (ESS). This paper focuses on design and implementation of a control structure for a totem-pole boost PFC with newfangled enhancement-mode Gallium Nitride (eGaN) FETs, not only to simplify the control implementation, but also to achieve high power quality and efficiency. The converter is designed to convert a 90-264-VAC input to a 385-VDC output for a 2.6-kW output power. Lastly, to validate the methodology, an experimental prototype is characterized and fabricated. The uttermost efficiency at 230 VAC attains 99.14%. The lowest total harmonic distortion in the current (ITHD) at high line condition (230 V) reaches 1.52% while the power factor gains 0.9985.

A fast and effective determination method of different species of vegetable seeds oil is vital in the plant oil industry. The near-infrared reflectance spectroscopy (NIRS) method was developed in this study to massively analyze the oil and moisture contents of Camellia gauchowensis Chang and C. semiserrata Chi seeds kernels. In the prediction models of NIRS, the levels of accuracy obtained were sufficient for C. gauchowensis Chang and C. semiserrata Chi, the correlation coefficient of which oil were 0.983 and 0.962, respectively, while which of moisture were 0.937 and 0.907, respectively. The near infrared spectrum of crush seeds kernels was more precise compared to intact kernels. Based on the calibration models of the two Camellia species, the NIRS predictive oil contents of C. gauchowensis Chang and C. semiserrata Chi seeds kernels were 48.71 ± 8.94% and 31.71 ± 7.39%, respectively, and the NIRS predictive moisture contents were 4.39 ± 1.08% and 3.49 ± 0.71%, respectively. Compared with the traditional chemical measurement, the rapid, precise measurement of oil and moisture of C. gauchowensis Chang and C. semiserrata Chi seeds kernels can be actualized by NIRS method.