High temperatures (HT) and high hydrostatic pressures (HHP) are characteristic of deep-sea hydrothermal vents and other deep crustal settings. These environments host vast and diverse microbial populations, yet only a small fraction of those populations have been successfully cultured. This is due, in part, to the difficulty of sampling while maintaining these in situ conditions and also replicating those high-temperature and high-pressure conditions in the laboratory. In an effort to facilitate more HT-HHP cultivation, we present two HT-HHP batch culture incubation systems for cultivating deep-sea vent and subsurface (hyper)thermophilic microorganisms. One HT-HHP system can be used for batch cultivation up to 110 MPa and 121°C, and requires sample decompression during subsampling. The second HT-HHP system can be used to culture microorganisms up to 100 MPa and 160°C with variable-volume, pressure-retaining vessels that negate whole-sample decompression during subsampling. Here, we describe how to build cost effective heating systems for these two types of high-pressure vessels, as well as the protocols for HT-HHP microbial batch cultivation in both systems. Additionally, we demonstrate HHP transfer between the variable-volume vessels, which has utility in sampling and enrichment without decompression, laboratory isolation experiments, as well as HHP filtration.

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (>70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

High pressure crystallization technique has been successfully used to prepare an elusive form II of a non-steroidal anti-inflammatory drug, Mefenamic acid. Single crystal of form II was grown at 0.3 GPa from an 4:1 methanol/ ethanol mixture as a solvent using Diamond Anvil Cell. Comparison of crystal structures show that the efficient packing of MA molecules in Form II results from the structural flexibility of MA acid molecules. Compression studies performed on the single crystal of form I resulted in 14 % decrease of unit cell volume up to 2.5 GPa. No phase transition was observed up to this pressure. A reconstructive phase transition is required to induce conformational changes in the structure, which is confirmed by crystallization at high pressure results.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

Abstract:High-pressure water jet technology has received extensive attention and application due to its high efficiency and environmental protection characteristics. The high-pressure water jet nozzle is its core component, and the research on the high-pressure water jet nozzle is conducive to improving the jet performance and improving the jet efficiency. This paper introduces the characteristics of water jet and the working principle of pure water jet, abrasive water jet, pulsed water jet and cavitation water jet, reviews the theoretical analysis and experiment of the predecessor's nozzle, briefly explains the application of high-pressure water jet and looks forward to the development trend of this technology.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

Runaway electrons (RAEs) generation in high-pressure gases is an important physical phenomenon that influences significantly discharge shapes and properties of initiated plasma. The diffuse discharges formed due to RAEs in air and other gases at atmospheric pressure find wide application. In the present review, theoretical and experimental results that explain the reason for the RAEs occurrence at high pressures are analyzed and recommendations are given on the implementation of conditions under which the runaway electron beam (RAEB) with the highest current can be obtained at atmospheric pressure. Experimental results were obtained using subnanosecond, nanosecond, and submicrosecond generators, including those specially developed for runaway electron generation. The RAEB were recorded by oscilloscopes and collectors with picosecond time resolution. To describe theoretically the phenomenon of continuous electron acceleration, the method of physical kinetics has been used based on the Boltzmann kinetic equation that takes into account the minimum but sufficient number of elementary processes, including shock gas ionization and elastic electron scattering. Results of modeling allowed the main factors to be established that control the RAE appearance, the most important of which is electron scattering on neutral atoms and/or molecules. Theoretical modeling has allowed the influence of various parameters (including the voltage, pressure, gas type, and geometrical characteristics of the discharge gap) to be taken into account. The results of research presented here allow the RAEs accelerators with desirable parameters to be developed and the possibility of obtaining diffuse discharges to be accessed under various conditions. The review consists of the Introduction, 5 Sections, the Conclusion, and the References.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

The structural stability of γ-boron is investigated using Raman spectra under high pressures up to 126 GPa at ambient temperature. The pressure dependence of all the Raman-active modes of the γ-boron is reported. We also observe amusing changes within the B3g and B1g Raman-active vibrational modes, which results in the phenomenon of merging first and then separating of the Raman peaks. In addition to the Raman measurements, the changes in crystal structure and force constants are calculated to reasonably explain the discrepancy between the two Raman modes in response to pressure. The results of the continuous shifts for all Raman modes with increasing pressure indicate that γ-boron remains stable below this pressure value, with no changes in either symmetry or structure.

The second-order factor effect of burner optical ports and edge inter-matrices (EIM) and the first-order factor of pressure on the soot formation process and behavior of premixed sooting flames in a high-pressure burner are numerically investigated here. Three-dimensional computational fluid dynamics (CFD) simulations of a premixed flame C₂H₄/air at p = 1.01 and 10 bar using a one-step chemistry approach are first performed to justify the satisfied predictability of the prospective axisymmetric two-dimensional (2D) and one-dimensional (1D) simulations. The justified 2D simulation approach shows the generation of an axial vorticity around the EIM and axial multi-vorticities due to the high expansion rate of burnt gases at the high pressure of 10 bar. This leads to the development of axial multi-sooting zones, which are manifested experimentally by visible luminous soot streaks, and to the boosting of soot formation conditions of a relatively low-temperature field, < 1800 K, and a high mixing rate of gases in combustion around and above the EIM location. Nevertheless, a tolerable effect on the centerline soot volume fraction (f_V) profile, f_V < 3%, is manifested only at high heights above the burner of the atmospheric sooting flame C₂H₄/air ϕ = 2.1, and early at the high pressure of 10 bar of this flame, f_V < 10%. Enhancing the combustion process reactivity by decreasing the rich equivalence ratio of the fuel/air mixture and/or rising the pressure results in the prior formation of soot precursors, which shifts the sooting zone upstream.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

The effects of psychological pressure on perceiving the height of a jump bar just before starting a high jump run was investigated. University students (N = 14) training for a high jump event performed 15 trials (3 practice, 6 pressure, and 6 non-pressure) in counterbalanced order in their daily practice environment. The height of the bar was judged as significantly higher on pressure trials compared to non-pressure trials. A regression analysis indicated that participants who reported increased subjective perceived pressure tended to judge the bar to be higher. There was no significant difference between pressure and non-pressure trials for the performance index, defined as the success rate. This study provides the first evidence that environmental perceptions prior to executing a motor task under pressure may make performance of the task appear to be more difficult.

Ultra-high temperature oxidation-resistant alloys (UTORAs) have received a lot of attention due to the increased research demand for deep space exploration around the world. But UTORAs have the disadvantages of easy oxidation and chalking. So, in this study, a UTORA was prepared by hot-press sintering on VZrHfNbTa (HEA) substrate coated with hafnium. The bonding mechanism, resistance to high-temperature oxidation, and hardness of the sample tests were carried out. The results show that zirconium in the matrix will diffuse into the hafnium coating during the high-temperature sintering process and form the HfZr alloy transition layer, the coating thickness of the composite is about 120 μm, and the diffusion distance of zirconium in the hafnium coating is about 60 μm, this transition layer chemically combines the hafnium coating and the HEA substrate into a monolithic alloy composite. The results of high-temperature oxidation experiments show that the oxidation degree of the hafnium-coated VZrHfNbTa composite material was significantly lower than that of the VZrHfNbTa HEA after oxidation in air at 1600 °C for 5 h. The weight gain of the coated sample after oxidation is 56.56 mg/cm2, which was only 57.7 % compared to the weight gain of the uncoated sample (98.09 mg/cm2 for uncoated), and the surface of the uncoated HEA showed obvious dents, oxidation, and pulverization occurred on the surface and interior of the sample. In contrast, the coated composite alloy sample mainly underwent surface oxidation sintering to form a dense HfO2 protective layer, and the internal oxidation of the hafnium-coated VZrHfNbTa composite alloy was significantly lower than that of the uncoated VZrHfNbTa HEA.

The poor oxidation resistance of refractory high-entropy alloys (RHEAs) is a major obstacle for their use in high-temperature engineering applications. Anti-oxidation coating technology is an effective method for improving the oxidation resistance. In this paper, the Si-20Cr-20Fe coating was prepared on MoNbTaTiW RHEA by a fused slurry method. The microstructural evolution and compositions of the silicide coating under high-temperature oxidation environment were studied. The results show that the silicide coating could effectively prevent the oxidation of the MoNbTaTiW RHEA. The initial silicide coating had a double-layer structure; a high silicon-content layer mainly composed of MSi2 as the outer layer and a low silicon-content layer mainly contained M5Si3 as the inner layer. Under high-temperature oxidation conditions, the silicon element diffused from the silicide coating to the RHEA substrate while the oxidation of the coating occurred. After oxidation, the coating was composed of an outer oxide layer and an inner silicide layer. The silicide layer moved toward the inside of the substrate, led to the increase of its thickness. Compared with the initial silicified layer, its structure did not change significantly. The structure and compositions of the oxide layer on the outer surface strongly depended on the oxidation temperature. This paper provides a strategy for protecting RHEAs from oxidation at high-temperature environments.

This study presents a comprehensive investigation of the formation, composition, and behaviour of oxide layers during the high-temperature oxidation of four different steel alloys (16Mo3, 13Cr, T24 and P91) at a uniform temperature of 650 °C. The research combines CALPHAD (CALculation of PHAse Diagrams) calculations, thermogravimetric analysis (TGA) and advanced microscopy techniques, including scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), to elucidate the complex mechanisms controlling oxidation kinetics and oxide layer development. CALPHAD calculations were used to determine the thermodynamically stable phases for each steel type at 650 °C. The results showed different phase compositions, highlighting the importance of steel composition in the formation of oxide layers. Each steel grade exhibited different kinetics, with 16Mo3 steel showing the highest oxidation rate, followed by 13Cr, T24 and P91. This variability highlights the role of steel composition, particularly chromium content, in determining oxidation behaviour. These results have significant implications for temporary overheating in industrial applications and contribute to a deeper understanding of oxidation processes in steels.

Hardaliye, a traditional non-alcoholic beverage, made from red grape pomace from wine production and produced by lactic acid fermentation with addition of different concentrations of whole/ground or heat-treated mustard seeds and of sour cherry leaves. Short shelf life of hardaliye limits its consumption and search in trend to process hardaliye to extend its shelf life. Thus, high hydrostatic pressure treatment of hardaliye drink with determination of changes in physicochemical and sensory properties in addition to microbial inactivation were studied according to Box-Behnken design. Maximum 5.10±0.00, 4.21±0.00, 5.38±0.59 and 5.05±0.22 log reductions were obtained in total mesophilic aerobic bacteria, total mold and yeast, Brettanomyces bruxellensis and Lactobacillus brevis by HHP. Shelf-life studies of the hardaliye samples were conducted with optimum processing parameters of 490 MPa, 29 oC for 15 min with the response variables of OD520 and inactivation of L. brevis. Both control and HHP treated samples were stored at 4 and 22 C for shelf-life studies. While control samples at 4 and 22 °C were spoiled at the 15th and 3rd days, HHP treated samples were spoiled after 108th and 228th days, respectively.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

Rocks are materials with a wide variety of structures and properties. These can be unprocessed conglomerates of conglomerated minerals as well as crystallized outcrop or metamorphic rocks. Their processing, especially shaping, poses many technological difficulties. Therefore, it is very important to answer the question of how these natural materials yield to high-pressure water jet and abrasive water. It is equally important to determine the effect of key process parameters such as pressure, water nozzle diameter and feed rate on cutting efficiency. The first two parameters determine the water output and power of the jet, while the third determines the jet erosion time per unit volume of material. Their interdependence, using appropriate evaluation indicators, allows to determine the energy intensity of processing and directions for its minimization.

Bi0.5Na0.5TiO3-0.06BaTiO3 (BNT-BT) thin films were prepared by both chemical solution (CSD) and pulsed laser deposition (PLD). The microstructure, dielectric, and ferroelectric properties were investigated. High stability of the dielectric permittivity (∆ɛ/ɛ(150 °C) ≤ ± 15%) over a wide temperature range from room temperature to 300 °C was obtained. Distinctly, the CSD film showed high TCC stability with variation of ± 5% up to 250°C. Furthermore, the CSD film showed an unsaturated ferroelectric hysteresis loop characteristic of the ergodic relaxor phase, however the PLD one exhibited almost saturated loop signature of the coexistence of both ergodic and non-ergodic states. The energy storage properties of the prepared films were determined using the P–E loops obtained at different temperatures. The results showed that these films exhibit stable and improved energy storage density comparable to the ceramic capacitors. Moreover, the CSD film exhibited more rigidity and better energy storage density that exceeds 1.3 J/cm3 under low applied field of 317 KV/cm as well as interesting efficiency in a large temperature range. The obtained results are very promising for energy storage capacitors operating at high temperatures.

In this study, we had investigated the use of high-pressure homogenization (HPH) as a novel pretreatment method for the extraction of sodium alginate (SA) from Laminaria japonica. Our results demonstrated that under optimal condition of 100 MPa HPH pressure, 4 cycles, pH 6.0, and 0.5% ethylene diaminetetra acetic acid tetrasodium salt (EDTA) concentration (w/v) for 3.0 hours, the extraction yield of HPH reached 34%, which was higher than that achieved by previous methods such as complex enzyme hydrolysis (CE), ultrasonic-assisted extraction (UAE), and complex enzyme-ultrasonic combined method (CE-UC). To further characterize the extracted SA, we conducted a comprehensive analysis using SEM, FTIR, MRS, NMR, XRD, TGA, and T-AOC assay. Our findings revealed the following: 1) HPH treatment significantly disrupted the structure of L. japonica cells and reduced their crystallinity to 76.27%, the lowest among all pretreatment samples; 2) the extracted SA had a greater tendency to form elastic gels; and 3) the antioxidant activity of HPH-extracted SA reached 0.02942 mgVceq∙mg-1, which was the highest among all tested methods. Based on these results, we concluded that HPH extraction not only increased the yield of SA but also enhanced its antioxidant activity.

Rice production, owing to its high-water requirement for cultivation, is very vulnerable to the threat of changing climate, particularly prolonged drought and high temperature. Such threats heighten the need for abiotic stress-resilient rice varieties with better yield potential. This review examines the physiological and molecular mechanisms of rice varieties to cope with stress conditions of drought (DS), high temperature (HTS) and their combination (DS-HTS). It appraises research studies in rice about its various phenotypic traits, genetic loci and response mechanisms to stress conditions to help craft new breeding strategies for rice varieties with improved resilience to abiotic stresses. This review consolidates available information on promising rice cultivars with desirable traits as well as advocates synergistic and complementary approaches in molecular and systems biology to develop new rice breeds that favorably respond to climate-induced abiotic stresses. The development of new breeding and cultivation strategies for climate-resilient rice varieties is a challenging task. It requires a comprehensive understanding of the various morphological, biochemical, physiological, and molecular components governing yield under drought and high temperature, but possible by implementing cohesive approaches involving molecular and systems biology approaches in genomics and molecular breeding, including genetic engineering.

Ultra-short laser pulses (1030 nm/230 fs) were used to laser ablate surface of crystalline sapphire. Laser ablated patterns were annealed at high temperature 1500∘C. Surface reconstruction took place removing ablation debris field at the edges of ablated pits in oxygen flow. Partial reconstruction of ripples was also observed.

(1) Background: Lifestyle changes, eventually associated with a nutraceutical, are recommended strategies for managing high-normal blood pressure (BP) patients with low-moderate cardiovascu-lar (CV) risk. Nitrates-enriched products (i.e., red beet extracts) may help reduce BP, exerting vas-oactive properties and enhancing adherence to lifestyle advice. Our study aimed to evaluate the effectiveness in clinical practice of generic written lifestyle advice and a beetroot-based nutraceu-tical prescription based on the 2018 ESC/ESH guidelines on 24-hour BP in a population with high-normal BP and low-moderate CV risk.; (2) Methods: A longitudinal observational study was con-ducted in two ESH hypertension excellence centres on 43 consecutive subjects with high-normal BP based on repeated office BP (OBP) measurements and a low-moderate CV risk. Twenty-four-hour ambulatory BP monitoring (ABPM) was carried out at baseline and three months after ge-neric written ESC/ESH advice for lifestyle changes associated with a nutraceutical containing 500 mg of dry beetroot extract; (3) Results: Mean age 50±11 years, 54% males, 58% overweight/obese, mean OBP 135±3/85±3 mmHg. At baseline, 24-hour BP, daytime BP and night-time BP were 127±7/80±6 mmHg, 131±8/83±6 mmHg and 118±8/70±5 mmHg, respectively, BP profiles compat-ible with hypertension status in some subjects. After a median follow-up of 98 (92-121) days, all BPs, except night-time diastolic BP, were significantly decreased: -3±6/-2±4 mmHg for 24-hour BP, -3.9±6.0/-3.0±4.0 mmHg for daytime BP and -3.3±7.4/-1.3±4.7 mmHg for night-time BP, respec-tively. No significant clinical changes in weight were detected. BP decreased independently of baseline BP level, gender, smoking status and BMI, while a more substantial decrease in BP was observed in older patients; (4) Conclusions: Our pilot study shows for the first time that written generic lifestyle advice based on ESC/ESH hypertension guidelines coupled with a beetroot-based nutraceutical may represent a valid initial non-pharmacological approach in subjects with high-normal BP and low-moderate CV risk even without personalized diet interventions.

Nowadays, with the development of laser weapons, the primary power supply of laser weapons puts forward more and more high demand for its performance. The pulsed power supply based on conventional homopolar inductor alternator (HIA) cannot meet the requirements any more. In order to improve the power density and efficiency, this paper proposes applying the high-temperature superconducting (HTS) HIA with slotless stator core to this power supply. In this paper, the design considerations of it are presented, and the comparisons between the two power supplies are discussed. The calculation results show that the power supply based on HTS machine has much larger power density than the conventional HIA, and the efficiency is also larger than the conventional HIA. This can improve the performance of laser weapons dramatically.

The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

By drilling periodic thru-holes in a suspended film, the phonon system can be modified. Being motivated by the BCS theory, the technique, so-called phonon engineering, was applied to a niobium sheet. The newly emergent high-T_c superconductivity, however, cannot be accounted for by the BCS theory. Rather, its exposed configuration, namely a square-lattice oxygen network, is reminiscent of the copper--oxygen plane in cuprate high-T_c superconductors. It turns out that its magnetic result is consistent with the principle of giant atom, which was developed by another heroes of superconductivity, Fritz London and John Slater, in the 1930s, several decades earlier than the propagation of BCS theory. The superconducting transition feature is discussed on the basis of a comprehensive theory of the giant atom---the theory of hole superconductivity.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Synthetic chalcomenite-type cupric selenite CuSeO₃∙2H₂O has been studied at room temperature under compression up to pressures of 8 GPa by means of single-crystal X-ray diffraction, Raman spectroscopy, and density-functional theory. According to X-ray diffraction, the orthorhombic phase undergoes an isostructural phase transition at 4.0(5) GPa with the thermodynamic character being first-order. This conclusion is supported by Raman spectroscopy studies which have detected the phase transition at 4.5(2) GPa and by the first-principles computing simulations. The structure solution at different pressures has provided information on the change with pressure of unit-cell parameters as well as on the bond and polyhedral compressibility. A Birch-Murnaghan equation of state has been fitted to the unit-cell volume data. We found that chalcomenite is highly compressible with a bulk modulus of 42 – 49 GPa. The possible mechanism driving changes in the crystal structure is discussed, being the behavior of CuSeO₃∙2H₂O mainly dominated by the large compressibility of the coordination polyhedron of Cu. On top of that, an assignation of Raman modes is proposed based upon density-functional theory and the pressure dependence of Raman modes discussed. Finally, the pressure dependence of phonon frequencies is also reported.

Present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometer-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. The research explores compositions with varying CoFe2O4 content, ranging from 0 up to 20 wt.%. Сonventional sintering in an air atmosphere is carried out at a temperature between 1100-1300 °C. The addition of ferrite nanoparticles was found to enhance the sintering process of cenospheres, resulting in improved material density and mechanical properties. Furthermore, the study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetization (Ms) and remanent magnetization (Mr)) was observed to strengthen. These findings provide valuable insights into the design and development of lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in electronics, telecommunications, and aerospace industries.

An innovative superconducting mechanism was developed based on a patented discovery of high temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electronical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under high or room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases and therefore, can be adapted to describe the superconducting phenomenon for other superconductors. If this superconducting mechanism can be successfully applied to other superconductive cases, it may be served as a tool for future research to bring the superconducting transition (critical) temperature T_c to exceed room temperature landmark and hence, the over a century dream of obtaining an applicable superconductor can be realized.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

This study aimed to use biomineralization technology to improve the bond strength of fiber-reinforced lightweight aggregate concrete (LWAC) after exposure to temperatures of 300 °C and 500 °C. The specimens of a control group (Group A) and two experimental groups (Group B and Group C) were prepared. These specimens healed themselves in different ways after exposure to high temperatures and pull-out tests. The self-healing method of Group A involved placing the specimen into an incubator. The self-healing method of Group B was the same as that of Group A. The self-healing method of Group C involved immersing the specimen in a mixed solution of urea and calcium acetate for two days, then taking it out and placing it in an incubator for two days. A cycle of four days was undertaken until the desired age was reached. After the specimens were healed to the planned age, the first and secondary pull-out tests and repair compound identification were carried out. After exposure to a temperature of 300 °C and self-healing for 90 days, compared with the specimens in Group A, the relative bond strength ratios of the secondary pull-out tests of the specimens in Group C increased by 20.3%. This indicates that biomineralization can effectively improve the bond strength of LWAC after high-temperature damage.

The Gleeble-1500D thermal simulation test machine was used to conduct the isothermal compression test on 21-4N at the strain rate ( ) of 0.01-10s-1, the deformation temperature (T) of 1273-1453K and the maximum deformation is 0.916. The data of the stress-strain ( - )were obtained. Based on the - data, the Johnson-Cook (J-C), modified J-C, Arrhenius and Back-Propagation Artificial Neural Network (BP-ANN) models were established. The accuracy of four models were verified, analyzed and compared. The results show that J-C model has a higher accuracy only under reference deformation conditions. When the deformation condition changes greatly, the accuracy of J-C model is significantly reduced. The coupling effect of T and of modified J-C model is considered, and the prediction accuracy is greatly improved The Arrhenius model introduces Zener-Hollomon (Z) to represent the coupling effect of T and , it has a fairly high prediction accuracy. And it can predict flow stress ( ) accurately at different conditions. The accuracy of BP-ANN model is the highest, but its learning rate is low, the learning and memory are unstable. It has no memory for the weights and thresholds of the completed training. So, there are certain limitations of it in use. Finally, a FEM of the isothermal compression experiment for four models were established, and the distribution of the equivalent stress field, equivalent strain field and temperature field with the deformation degree of 60% were obtained.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

As the most serious of the many worse new pathological changes caused by diabetes, there are many risk factors for the occurrence and development of DR. It mainly includes hyperglycemia, hypertension, hyperlipidemia and so on. Among them, hyperglycemia is the most critical cause, which plays a key role in the pathological changes of DR.High-sucrose diets(HSDs) lead to elevated blood glucose levels in vivo, which, through oxidative stress, inflammation, the production of AGEs and VEGF, causes plenty of pathological damages to the retina and ultimately bring about loss of vision. The existing therapies for DR primarily target the terminal stage of the disease, when irreversible visual impairment has appeared. Therefore, early prevention is particularly critical. Early prevention of DR-related vision loss requires adjustments to dietary habits, mainly by reducing sugar intake. This article primarily discusses the risk factors, pathophysiological processes, and molecular mechanisms associated with the development of DR caused by HSDs. It aims to raise awareness of the crucial role of diet in the occurrence and progression of DR, promote timely changes in dietary habits, prevent vision loss, and improve the quality of life. The aim is to make people aware of the importance of diet in the occurrence and progression of DR. According to the dietary modification strategies we give, patients can change their poor eating habits timely, avoid the retinopathy that can be avoided theoretically, and obtain a excellent outcome.

Background: Annual influenza epidemics are a serious public health problem, causing particularly severe morbidity and mortality in high-risk groups. The study aimed to understand Poles' attitudes and beliefs towards influenza vaccinations in the flu season of 2022–2023, analyze preferences and unmet needs regarding influenza vaccinations, and examine the perception and acceptance of the influenza vaccine among individuals at risk of flu complications. Methods: A cross-sectional survey-based study was carried out on a sample of 1446 respondents. The Google Forms questionnaire was created and disseminated electronically using social media and e-mail. The pre-test was performed at the beginning of the project. Results: The majority of respondents (71%) could identify "high-risk groups" recommended for influenza vaccination. Furthermore, it was observed that individuals aged 21 to 59 demonstrated a higher level of knowledge in this regard compared to those below 20 and above 65 years old, and individuals with higher and medium education levels were much better at identifying risk groups for influenza virus infection. The majority of respondents (52.01%) reported receiving influenza vaccination at some point in the past, with 32.12% receiving it in the 2022–2023 flu season and 41.09% in the 2021–2022 season. The majority of respondents declaring acceptance of the vaccine for the 2022-2023 season were in the high-risk group. Only 17.28% of respondents declared receiving both influenza and SARS-CoV-2 vaccines in the 2022-2023 season, with the vast majority being respondents from the "high-risk group" (p

Concrete has become the most common construction material showing among other advantages good behaviour when subjected to high temperatures. Nevertheless, concrete is usually reinforced with elements of other materials such as steel in the form of rebars or fibres. Thus, the behaviour under high temperatures of these other materials can be critical for structural elements. In addition, concrete spalling occurs when concrete is subjected to high temperature due to internal pressures. Micro polypropylene fibres (PP) have shown to be effective for reducing such spalling although this type of fibres barely improve any of the mechanical properties of the element. Hence, a combination of PP with steel rebars or fibres can be effective for the structural design of elements exposed to high temperatures. New polyolefin fibres (PF) have become an alternative to steel fibres. PF meet the requirements of the standards to consider the contributions of the fibres in the structural design. However, there is a lack of evidence about the behaviour of PF and elements made of polyolefin fibre reinforced concrete (PFRC) subjected to high temperatures. Given that these polymer fibres would be melt above 250 °C, the behaviour in the intermediate temperatures was assessed in this study. Uni-axial tests on individual fibres and three-point bending tests of PFRC specimens were performed. The results have shown that the residual load-bearing capacity of the material is gradually lost up to 200 °C, though the PFRC showed structural performance up to 185°C.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

High temperature (HT) geothermal wells can provide green power 24h a day 7 days a week. Harsh environmental and operational conditions, long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests, field exposures in an HT geothermal well (300-350oC) as well as a numerical model to complement the experimental results. Performances of calcium-aluminate-cement (CAC)-based composites and calcium free cement were compared against reference Ordinary Portland Cement (OPC)/silica blend. The stability and degradation of the tested materials was characterized by crystalline composition, thermo-gravimetric, and elemental analyses, morphological studies, water-fillable porosity, and mechanical properties measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict field-scale behavior of the cement sheath under geothermal well conditions.

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

Grouting materials with good insulation and reinforcement performance are key factors in solving the temperature control problem of high temperature tunnels using curtain grouting, while existing grouting materials cannot balance their working performance and insulation performance in high-temperature environments. In response to the above issues, this article uses red mud to prepare high ground temperature red mud based grouting materials (RMGS), and conducts tests on the working performance (viscosity, setting time, compressive strength) and insulation performance (thermal conductivity, specific heat capacity) of grouting materials at different temperatures (20, 40, 60, and 80 ℃), and analyzes the variation patterns and micro mechanisms of various characteristics with temperature. The results indicate that an increase in temperature will accelerate the viscosity development and condensation of the grouting material, and lead to a decrease in thermal conductivity and specific heat capacity. In addition, an appropriate temperature can also improve the compressive strength of the material. The increase in temperature will accelerate the hydration reaction rate of the grouting material and the development of internal pores, which is the reason why temperature affects the performance of the grouting material. In engineering applications, cement slurry is suitable for static water grouting, cement-sodium silicate slurry is suitable for dynamic water grouting, and RMGS is suitable for high-temperature tunnel grouting.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Three hundred ten 12-wek-old laying quails (155 each) were randomly selected from the initial population and kept in individual battery cages. The measurements of growth and egg production were determined to derive RFI. The relationship between RFI and egg quality, blood parameters and carcass characteristics was also determined. The results indicated that the gray quails had significantly higher egg mass and lower broken eggs compared to the white quails. A significant increase for eggshell strength and shell % was found in eggs produced from gray quails compared to white counterparts, although the shell thickness was the same. The results of multiple regression analysis clearly identified a significant effect of metabolic body weight and egg mass in computing expected feed intake rather than body weight gain in both varieties of Japanese quails. Strongly positive correlation between RFI and feed intake in both gray and white quail varieties was found. The same trend was also observed for feed conversion ratio (FCR). Therefore, including RFI in selection criteria of Japanese quail to improve FCR under high environmental temperature is highly recommended.

Graphene nanostructures (GNS) are among the most promising materials for creating supercapacitors. However, GNS are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In this work, we investigated the efficiency of using few-layer graphene (FLG) with the number of layers is not more than 5 synthesized under Self-propagating high-temperature synthesis (SHS) conditions as basic material for supercapacitors. Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG has a higher specific capacitance – 65 F×g-1 compared to the sample from AC, the specific capacitance of which is 35 F×g-1, for a speed of 5 mV×s-1 these values are 170 and 64 F×g-1, respectively. The drop in capacitance over 1000 cycles was 4%, which indicates a sufficiently high stability of FLG and allows us to consider FLG as perspective material for use in supercapacitors.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

This research focuses on the Hopf bifurcation occurring at a singular point with high-order degeneracy in a class of three-dimensional systems. Based on center manifold theorem, by expanding the technique for determining singular point values of degenerate singularities in two-dimensional systems, the formal series method to determine the singular point values at the high-order degenerate critical point is discussed. Furthermore, a class of specific three-dimensional differential systems with high-order degenerate singularities is explored. By computing the singular point values and determining center conditions, we proved that a minimum of 5 small-amplitude limit cycles in the vicinity of the origin. This research provides new perspectives on the center problem and limit cycle bifurcation in high-dimensional systems with high-order degenerate singular points.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

Fibre reinforced concrete (FRC) has been used for decades in certain applications of the construction industry, such as tunnel linings and precast elements, but has experienced an important progress in recent times, boosted by the inclusion of guidelines for their use in some national and international standards. Traditional steel fibres have been studied in depth and their performance is well known although in recent years new materials have been proposed as possible alternatives. Polyolefin macro-fibres, for instance, have proven to enhance the mechanical properties of concrete and the parameters that define their behaviour (fibre length, fibre proportion or casting method, for instance) have been identified. These fibres overcome certain traditional problems related to steel fibres, such as corrosion or their interaction with magnetic fields, which can limit the use of steel in some applications. The behaviour of polyolefin fibre reinforce concrete (PFRC) has been numerically reproduced with success through an embedded cohesive crack formulation that uses a trilinear softening diagram to describe the fracture behaviour of the material. Furthermore, concrete behaves well under high temperatures or fire events, especially when it is compared with other construction materials, but the behaviour of PFRC must be analysed if the use of these fibres is to be extended. To this end, the degradation of PFRC fracture properties has been recently experimentally analysed under a temperature range between 20ºC and 200ºC. As temperature increases, polyolefin fibres modify their mechanical properties and their shape, which reduce their performance as reinforcement of concrete. In this work, those experimental results, which include results of low (3 kg/m3) and high (10 kg/m3) proportion PFRC specimens, are used as reference to study the fracture behaviour of PFRC exposed to high temperatures from a numerical point of view. The experimental load-deflection diagrams are reproduced by modifying the trilinear diagram used in the cohesive model, which helps to understand how the trilinear diagram parameters are affected by high temperature exposure. Finally, some expressions are proposed to adapt the initial trilinear diagram (obtained with specimens not exposed to high temperature) in order to numerically reproduce the fracture behaviour of PFRC affected by high temperature exposure.

Chilean jack mackerel (Trachurus murphyi) is recognized as one of the most valuable pelagic resources across the southeast Pacific Ocean. Despite its nutritious properties it is an underused resource due to its rapid spoilage. The use of high hydrostatic pressure (HHP) for the processing of aquatic products could be an efficient alternative to cold storage since HHP might inactivate microbial pathogens and slow down spoilage microorganisms, therefore extending the product’s shelf life. The aim of the study was to compare the effect of HHP at 450 and 550 MPa for 3 min on the physicochemical properties of jack mackerel muscle undergoing pre- and post-rigor mortis stage and further storage for 26 days at 4°C. pH, total volatile basic nitrogen, trimethylamine, color, water-holding capacity, and texture were assessed. The proximate composition, pH, total volatile basic nitrogen, trimethylamine, color, water holding capacity, and texture, showed significant changes between untreated and treated samples, while the water holding capacity was virtually unaffected. Overall results showed an acceptable and long-lasting edible quality of Trachurus murphyi stored at 4°C when preserved through HHP. These findings suggest that the HHP might be able to industrially scale the production of highly physicochemical superior and minimally processed fish products.

This paper reviews state of the art Additive Manufactured (AM) IN718 alloy intended for high temperature applications. AM processes have been around for decades and have gained traction in the past five years due to the huge economic benefit it brings to manufacturers. It is crucial for the scientific community to look into AM IN718 applicability in order to see a step-change in the production. Microstructural studies reveal that the grain structure plays a significant role in determining the fatigue lifespan of the material. Controlling IN718 respective phases such as the ϒ’', δ and Laves phase is seen to be crucial. Literature reviews have shown that the mechanical properties of AM IN718 were very close to its wrought counterpart when treated appropriately. Higher homogenization temperature and longer ageing were recommended to dissolve the damaging phases. Various surface enhancement techniques were examined to find out their compatibility to AM IN718 alloy that is intended for high temperature application. Laser shock peening (LSP) technology stands out due to the ability to impart low cold work which helps in containing the beneficial compressive residual stress it brings in high temperature fatigue environment.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

Molecular dynamics simulation is currently the theoretical technique eligible to simulate a wide range of systems from soft condensed matter to biological systems. However, of the excellent results that the technique has arrogated, this approach remains computationally expensive, but with the emergence of the new supercomputing technologies bases on graphics processing units graphical processing units-based systems GPUs, the perspective has changed. The GPUs allow performing large and complex simulations at a significantly reduced time. In this work, we present recent innovations in the acceleration of molecular dynamics in GPUs to simulate non-Hamiltonian systems. In particular, we show the performance of measure-preserving geometric integrator in the canonical ensemble, that is, at constant temperature. We provide a validation and performance evaluation of the code by calculating the thermodynamic properties of a Lennard-Jones fluid. Our results are in excellent agreement with reported data reported from literature, which were calculated with CPUs. The scope and limitations for performing simulations of high-throughput MD under rigorous statistical thermodynamics in the canonical ensemble are discussed and analyzed.

The likelihood of pre-hypertensive young adults developing hypertension has been steadily increasing over the past few years. Despite the fact that aerobic exercise training (AET) has demonstrated positive results in lowering high blood pressure, the efficacy of different types of AET among pre-hypertensive young adults has not been well-established. The objective of this study was to evaluate the effectiveness of high-intensity interval training (HIIT) and continuous moderate-intensity training (CMT) on blood pressure (BP) of physically inactive pre-hypertensive young adults. 32 adults (age 20.0±1.1 years and BMI 21.5±1.8) were randomly assigned into 3 groups: HIIT, CMT and control (CON). HIIT and CMT groups participated in 5 weeks of AET; while the CON group followed a DASH diet plan only. The HIIT protocol consisted of 1:4 minute work to rest ratio of participants 80%-85% heart rate reserve (HR-reserve) and 40%-60% HR-reserve respectively for 20-minutes, CMT group exercised at 40%-60% of HR-reserve continuously for 20-minutes. In both HIIT and CMT groups, systolic blood pressure (SBP) (3.8±2.8 mmHg, P=0.002 VS 1.6±1.5 mmHg, P=0.011) was significantly reduced. While, significant reductions in the diastolic blood pressure (DBP) (2.9±2.2 mmHg, P=0.002) and mean arterial pressure (MAP) (3.1±1.6mmHg, P<0.0005) were noted only in the HIIT group. No significant differences in SBP (-0.4±3.7 mmHg, P=0.718), DBP (0.4±3.4 mmHg, P=0.714), or MAP (0.1±2.5mmHg, P= 0.892) were observed in the CON group. Both HIIT and CMT decreased the BP in physically inactive pre-hypertensive young adults; however, HIIT yielded more beneficial results in terms of reducing the SPB, DBP and MAP.

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

Standards are not only crucial for obtaining a certification for practical use, but also an essential guidance for inferring how and what to simulate as well test experimentally. This paper examines the potential applicability of existing standards from various domains, including aerospace and automotive, to Wing-Structure- Integrated high-pressure Hydrogen Tanks (SWITHs). It highlights the associated challenges and uncertainties, acknowledging the absence of a single, all-encompassing standard for SWITHs. We embark on an exploration aimed at identifying alternative standards that are best suited for SWITHs. The analysis scrutinizes existing standards that could potentially facilitate SWITH certification, with a particular focus on the inclusivity of externally loaded hydrogen tanks. Assessment criteria are established to filter standards that best meet the needs of SWITHs. Through this process, we identify two key standards that present themselves as the most promising alternatives. Moreover, we delineate the technical constraints involved in selecting the maximum nominal working pressure for high-pressure tanks intended for burst tests. Our findings reveal a current upper limit of 525 bar, imposed by the limitations of existing test facilities. The study underscores that these standards should serve as flexible guiding frameworks rather than rigid protocols, encouraging progressive development in the SWITH field.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

Background of the Study: We investigated the link between hypertension and cancer since it has been suggested that hypertension may raise the long-term risk of cancer. Previous large observational cohort studies found that greater blood pressure (BP) was related to a higher risk of cancer. Mendelian randomization (MR) was utilized to produce less confounded blood pressure estimates (BP) on overall and site-specific malignancies. The study aims to draw conclusions on the relationship between high blood pressure and cancer. Methods: Studies on high blood pressure and various malignancies are inconclusive, except for renal cell carcinoma. However, given that most meta-analyses only contained a limited number of trials, some relative risks had small to moderate magnitudes, and several may have been impacted by residual confounding, careful interpretation is necessary. The study was conducted using the meta-analysis technique. Cochran's Q test and I2 test were used to assess statistical heterogeneity between studies in the current investigation for research involving two or more cause and outcome combinations. Results: Positive correlations were also reported between high blood pressure and esophageal adenocarcinoma, squamous cell carcinoma, liver, and squamous cell carcinoma. However, most studies lacked multivariable adjustments. Physical and numerical risk of cardiovascular disease is linked to bowel cancer but no other cancers. According to a meta-analysis, hypertensive persons could also be at increased danger of gastrointestinal and breast cancer. Most meta-analyses comprised several trials with moderate or mild hazard ratios.ConclusionDifferent types of cancers have been noted to be directly caused by hypertension. In addition, some treatments have also been associated with the side effects of cancer treatments to cause hypertension. Women facing hypertension have an increased risk of getting breast cancer. Although some cancers showed a real relationship with hypertension, others had no connection at all.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.

By means of density functional theory (DFT) calculations, we have investigated the effect of hydrostatic pressure on the structural, electronic and elastic properties of the barium-doped silicon clathrate Ba8Si46 in the type-VIII structure (α phase). Physical properties are calculated under different conditions of pressure (0 GPa to 45 GPa) using the GGA-PBE functional, those calculations have been performed using the Cambridge serial total energy package CASTEP code within the Materials Studio package. Electronic properties have shown that the type-VIII Ba8Si46 has metal-like properties with a fundamental bandgap of 1 eV. Under pressure the fundamental bandgap increases slightly and the positions of the valence band maximum VBM and the conduction band minimum CBM remain unchanged. We found that the compound is mechanically stable under the pressure range, but this needs to be confirmed experimentally through synthesis, a comparison with the type-I and the guest-free counterparts has exhibited promising features for the type-VIII Ba8Si46.

Semantic segmentation of high-resolution remote sensing images provides detailed and precise feature information, playing a pivotal role in decision-making and analysis in sectors such as water management, agriculture, military, and environmental protection. However, most methods merely combine features from various branches directly, without a mechanism for spatial location feature screening, and treat all extracted features as equally important. To overcome these limitations, we introduce a novel spatially adaptive interaction network (SAINet) for dynamic interaction across different features in remote sensing semantic segmentation task. Specifically, we propose a spatial refined module that leverages local context information to filter spatial locations and extract salient regions. Following this, we introduce an innovative spatial interaction module that uses a spatial adaptive modulation mechanism to dynamically select and allocate spatial position weights. This facilitates interaction between local salient areas and global information, allowing the network to focus more on relevant regions. This flexible approach enables the network to capture more informative features, thereby enhancing segmentation accuracy. Experiments conducted on the DeepGlobe, Vaihingen, and Potsdam public datasets confirm the effectiveness and capability of SAINet. Our code and models will be publicly available

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

Climate change is expected to increase the frequency and severity of abiotic stresses that lead to loss of crop yield. We investigated the effect of salinity (S), short episodes of high temperature (HS) and combination of S+HS at the reproductive phase on dead pericarps properties and yield of the crop plant Brassica juncea. Three intervals of HS resulted in massive seed abortion; seeds from salt-treated plants germinated poorly. Pericarp extracts of salt-treated plants reduced seed germination of B. juncea; all pericarp extracts completely inhibited seed germination of tomato and Arabidopsis; removal of pericarp extracts restored seed germination. HS reduced all metabolites accumulated in dead pericarps, except for upregulation of isomaltose and cellobiose. Salt induced alteration in metabolite levels including increase in proline, reduction in TCA intermediates and changes in phytohormone levels. Proteome analysis revealed hundreds of proteins stored in dead pericarps whose levels and composition were altered under salt stress. The integration of metabolic and proteomic data showed that changes in metabolites were highly correlated with changes in proteins involved in their biosynthetic pathways. Thus, besides providing a physical shield for seed/embryo protection dead pericarps store beneficial substances whose levels, composition and biological function are altered under stress, further highlighting the elaborated function of dead organs enclosing embryos in seed biology and ecology. The detrimental effect of HS on crop production might have implications for global food security in the face of climate change.

Background: Early postoperative airway management after laryngo-tracheal surgery is crucial. Acute respiratory failure due to glottis’ oedema may occur, requiring reintubation. This can prolong ventilatory assistance, jeopardizing the anastomosis. To date, only judicious steroid administration and fluid management are available to avoid more invasive procedures. High-Flow-Oxygen-Therapy(HFOT) is a noninvasive O2 support method providing humidification, warmed air, Positive-End-Expiratory-Pressure(AIRVO2). No data exist about HFOT use to prevent early complications after laryngo-tracheal surgery. Methods: Between Sept.2020-Sept.2022, 107 consecutive patients underwent laryngo-tracheal surgery received HFOT(Group A). Data and long-term results were compared with those of 80 patients operated between Sept.2018-Aug.2020(Group B), when HFOT was not available. All patients were operated in a single center. No pre- or post-operative settings changed, except for HFOT introduction. We analyzed and compared the risk for “delayed” reintubation (unexpected reintubation within the first 24-48 hours after extubating/laryngeal mask removal) in the two groups. Results: No patients reported HFOT-related adverse events. Control group(B) presented “delayed” reintubation in 37% (p= 0.027), Intensive Care Unit admission in 67%(p=0.005) and longer hospital stay(p=0.001) compared to HFOT group(A). Minor complications rate was 3% in both group and overall mortality was 0%. Re-stenosis was described in 4.6% of HFOT group, without a statistically significant difference (p=0.7006). Conclusions: Our study is the first to investigate HFOT use in patients undergoing laryngo-tracheal surgery, potentially representing a consistent innovation in the peri-operative management of these patients. With the limit of a retrospective series, we would suggest HFOT use for preventing post-operative reintubation rate, possibly reducing ICU admission and hospital stay.

Primary ciliary dyskinesia (PCD) is an inherited disorder that impairs motile cilia, essential for respiratory health, with a reported prevalence of 1 in 16,309 within Hispanic populations. Despite having the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in 70% of Puerto Rican patients, the characterization of the ciliary dysfunction remains unidentified due to the unavailability of advanced diagnostic modalities like High-Speed Video Microscopy Analysis (HSVA). Our study implemented HSVA for the first time on the island as a tool to better diagnose and characterize the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in Puerto Rican patients. By applying HSVA, we analyzed the ciliary beat frequency (CBF) and pattern (CBP) in native Puerto Rican patients with PCD. Our results showed decreased CBF and a rotational CBP linked to the RSPH4A founder mutation in Puerto Ricans, presenting a novel diagnostic marker that could be implemented as an axillary test into the PCD diagnosis algorithm in Puerto Rico. The integration of HSVA technology in Puerto Rico substantially enhances the framework for PCD evaluation and diagnosis, facilitating prompt detection and early intervention for improved disease management. This initiative, demonstrating the potential of HSVA as an adjunctive test within the PCD diagnostic algorithm, could serve as a blueprint for analogous developments throughout Latin America.

Among the major systems of high-speed rail, the arch network relationship, wheel-rail relationship and fluid-structure coupling relationship are important links affecting the performance of high-speed rail, and also the main control factors affecting the speed limit of high-speed rail. From this perspective, the contact state and interactive relationship between pantograph and catenary are the key factors affecting the forward performance of high-speed rail. As a key component in the pantograph system, the actuator is responsible for adjusting the contact force and position between the pantograph and the contact line. The performance characteristics of the actuator, such as response speed, accuracy, stability and durability, directly affect the control performance of the whole pantograph system. In this paper, the research status of the active control technology of high-speed railway pantograph is reviewed, and the future development direction is pointed out, which provides a new idea for the development of pantograph technology.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

The cornerstone of molecular magnetism is a detailed understanding of the relationship between structure and magnetic behaviour, i.e. the development of magneto-structural correlations. Traditionally, the synthetic chemist approaches this challenge by making multiple compounds that share a similar magnetic core but differ in peripheral ligation. Changes in the ligand framework induce changes in the bond angles and distances around the metal ions which are manifested in changes to magnetic susceptibility and magnetisation data. This approach requires the synthesis of series of different ligands and assumes that the chemical/electronic nature of the ligands and their coordination to the metal, the nature and number of counter ions and how they are positioned in the crystal lattice, and the molecular and crystallographic symmetry have no effect on the measured magnetic properties. In short, the assumption is that everything outwith the magnetic core is innocent, which is a huge oversimplification. The ideal scenario would be to have the same complex available in multiple structural conformations, and this is something that can be achieved through the application of external hydrostatic pressure, correlating structural changes observed through high pressure single crystal X-ray crystallography with changes observed in high pressure magnetometry, in tandem with high pressure inelastic neutron scattering (INS), high pressure electron paramagnetic resonance (EPR) spectroscopy and high pressure absorption/emission/Raman spectroscopy. In this review, which summarises our work in this area over the last 15 years, we show that the application of pressure to molecule-based magnets can (reversibly): (1) lead to changes in bond angles, distances and Jahn-Teller orientations; (2) break and form bonds; (3) induce polymerisation/depolymerisation; (4) enforce multiple phase transitions; (5) instigate piezochromism; (6) change the magnitude and sign of pairwise exchange interactions and magnetic anisotropy and (7) lead to significant increases in magnetic ordering temperatures.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Co-doped SnO2 nanocrystals with tetragonal rutile-type (space group P42/mnm) structure have been investigated using in-situ high-pressure synchrotron angle dis-persive X-ray diffraction till 20.9 GPa at ambient temperature. The analysis of ex-perimental results based on Rietveld refinements suggest that rutile-type SnO2 un-dergoes a structural phase transition at 14.2 GPa to an orthorhombic CaCl2-type phase (space group Pnnm) with no coexistence during the phase transition. No further phase transition is observed till 20.9 GPa. The low-pressure and high-pressure phases are related via a group/subgroup relationship. However, as a discontinuous change in the unit-cell volume is detected at the phase transition, thus, the phase transition can be classified as first-order type. On decompression the transition is found to be re-versible. The results are compared with previous high-pressure studies on SnO2.

Red mud is a hazardous waste of alumina industry that contains high amounts of iron, aluminum, titanium and REEs. One of the promising methods for the extraction of iron from red mud is car-bothermic reduction with the addition of sodium salts. This research focuses on the process of hy-drochloric high-pressure acid leaching using 10–20% HCl of two samples of non-magnetic tailings obtained by 60-minute carbothermic roasting of red mud at 1300 °C and the mixture of 84.6 wt. % of red mud and 15.4 wt. % Na2SO4 at 1150 °C, respectively, with subsequent magnetic separation of metallic iron. An influence of temperature, leaching duration, solid-to-liquid-ratio and acid con-centration on dissolution behavior of Al, Ti, Mg, Ca, Si, Fe, Na, La, Ce, Pr, Nd, Sc, Zr were studied. Based on the investigation of the obtained residues, mechanism of passing of valuable elements into the solution was proposed. It has shown that 90% Al, 91% Sc and above 80% of other REEs can be dissolved under optimal conditions; Ti can be extracted into the solution or the residue depending on the leaching temperature and acid concentration. Based on the research results, novel flowsheets for red mud treatment were developed.

High-strength wastewaters from a variety of sources, including the food industry, domestic septage and landfill leachate, are often hauled to municipal wastewater treatment plants (WWTPs) for co-treatment. Due to their high organic loadings, these wastewaters can cause process upsets in both the WWTP’s liquid and solids treatment trains and consume organic treatment capacity, leaving less capacity available to service customers in the catchment area. A novel pre-treatment method, the Waste Activated Sludge-High Rate (WASHR) process, is proposed to optimize the co-treatment of high-strength wastewaters. The WASHR process combines the contact stabilization and sequencing batch reactor processes. It utilizes waste activated sludge from the municipal WWTP as its biomass source, allowing rapid start-up. Bench scale treatment trials of winery wastewater confirm the WASHR process can reduce loadings on the downstream WWTP’s liquid treatment and solids treatment trains. A case study approach is used to confirm the economic viability and environmental sustainability of the WASHR process compared to direct co-treatment using life cycle cost analyses and greenhouse gas emissions estimates.

A high intake of carbohydrates, associated with obesity, is one of the major causes of fatty liver disease in humans. This study investigated how high carbohydrate intake induces fatty liver disease in Blunt snout bream (Megalobrama amblycephala). Blunt snout bream were fed a high-carbohydrate diet (HCBD) for 60 days. Their growth indices were evaluated, and the transcriptomes, metabolites, biochemistry, and histology of their blood and livers were analyzed. The final weight, weight gain, specific growth rate, and feed conversion ratio were all higher in the HCBD group than in the control group, but not significantly so (P > 0.05). The hepatosomatic index (HSI) differed significantly in the two groups (P < 0.05), and the metabolomics results showed that a high carbohydrate intake induced significant increases in plasma α/β-glucose, succinate, and tyrosine, which could increase hepatic glycogen and triglyceride. Low levels of betaine were also found in the livers of the HCBD group. The histology and blood biochemistry results suggested abnormal liver, with excessive lipid accumulation and liver damage. A transcriptome analysis and quantitative reverse transcription–PCR (RT–qPCR) indicated that the expression of the factors INSR, IRS, PI3K, PDK, AKT, ACC, IL6, AP1, ChREBP-MLX, PEPCK, and FBP in the insulin signaling pathway was significantly upregulated and that of SOCS3, GSK3β, and AMPK significantly downregulated in the HCBD. This pattern is associated with the nonalcoholic fatty liver disease (NAFLD) pathway. This study extends our understanding of how high carbohydrate causes increased fat deposition in the liver, enhanced glycolysis (α/β-glucose) in the plasma, and reduced betaine in the liver. This leads to activation of hepatocyte insulin resistance and lipogenesis by regulating the expression of genes related to fatty liver disease.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

Ultra high molecular weight polyethylene (UHMWPE) is a thermoplastic high-performance polymer in high demand for biomedicine, ship and machine building, anthropomorphic robots and smart prostheses. Highly oriented UHMWPE fibers possess record specific strength and may also be used for the fabrication of self-reinforced PE-PE composites (SRPEC). The temperature evolution study of the small-angle X-ray scattering (SAXS) signature of the supramolecular structure of UHMWPE can help reveal their important role in the mechanism of the shape memory effect in SRPEC. The laboratory SAXS–WAXS beamline XEUSS 3.0 was used for in situ studies of the nanostructure parameters in unidirectional SRPEC. Namely, the radius of gyration and the dimensionality factor were extracted from 2D SAXS patterns using several fitting algorithms. Significant changes of these parameters occurred in temperature ranges that correspond to the initiation of the shape memory effect and melting. The relationship between the material anisotropy and 2D SAXS patterns are discussed in the context of the supramolecular structure evolution.

In this study, alfalfa silage with different packing densities (500 kg/m3, 600 kg/m3 and 700 kg/m3) were set up under outdoor high temperature and indoor normal temperature. The chemical composition, fermentation quality and microbial community of alfalfa silage were analyzed. The results showed that DM and WAC content decreased with the increase of density. When the density is 600kg/m3, CP content reaches the maximum and ADF content is the lowest. Temperature has a certain effect on alfalfa silage. The content of Lactobacillus plantarum fermented at high temperature is lower than that fermented at normal temperature. At the same time, the content of Lactobacillus plantarum decreased with the increase of packing density. However, the content of Lactobacillus plantarum was the lowest when the packing density was 600 kg/m3 at high temperature. In summary, this study explained the effects of different temperature and density on alfalfa fermentation quality and microbial community, and clarified that the density should be reasonably controlled within 600 kg/m3 during alfalfa silage, providing theoretical support for production practice.

Food and Agricultural Organisation estimates from 2014 suggest 64% of the high seas migratory stocks are either overfished or undergoing overfishing. Illegal fishing exacerbates the damage to marine ecosystems, human rights, and food security, and is yet to be included in the recent United Nations (UN) draft agreement to protect high seas biodiversity. We used catch data from the Sea Around Us Project to determine trends in fishing gear use and the catches of countries fishing in the high seas. Using Two-way ANOVA, Principal Coordinates Analysis, and SIMPER Test, we found that Spain, Taiwan, Japan, Indonesia, and Ecuador had the highest catches in 2004-2014. Each decade, only 1 in 10 countries (10.8%) caught over 500,000 tonnes, leaving the remaining 90% of countries catching less than 500,000 tonnes. Further analysis showed the mean high seas catch per fishery decreased 55% between the 2000s and the 2010s. Purse seine and longline were increasingly used towards the 2010s. Catch from purse seine and longline accounted for 70.5% and 78.4% of total high seas catch in 1950-2014 and 2004-2014, respectively. Discards were unreported throughout 1950-2014, and the reporting levels of landings varied greatly between countries and gears. We call for immediate action and recommend (1) including international, overarching high seas governance to end illegal and unsustainable fishing in the high seas in the UN draft agreement, and (2) using large mobile marine protected areas in high seas fisheries management through the UN draft agreement.

This study evaluated batch fermentation modes, namely, separate hydrolysis and fermentation (SHF), Quasi-simultaneous saccharification and fermentation (Q-SSF), and simultaneous saccharification and fermentation (SSF), and fermentation conditions, i.e., enzyme and yeast loadings, nutrient supplementation and sterilization, on high titer bioethanol production from SPORL-pretreated Douglas-fir forest residue without detoxification. The result indicated Q-SSF and SSF were obviously superior to SHF operation in terms of ethanol yield. The enzyme loading showed a strong positive correlation between enzyme loading and the ethanol yield. The nutrient supplementation and sterility was not necessary for ethanol production from SPORL-pretreated Douglas-fir. The yeast loading showed no significant influence on the ethanol yield for typical SSF conditions. The terminal ethanol titer of 43.2 g/L, or 75.1% theoretical based on glucose, mannose, and xylose theoretical was achieved when SSF was conducted at the condition of following: whole slurry solids loading of 15%, enzyme loading of 20 FPU/g glucan, 1.8 g/kg (wet) yeast loading, without nutrition supplementation and sterilization, at 38°C, on shake flask at 150 rpm for 96h. It is believed that with mechanical mixing, enzyme loading can be substantially reduced with affect ethanol yield by using a long fermentation time.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.