The purpose of this study is to investigate the failure mechanism and preventive strengthening methods of prefabricated full length small box girder (PSBG) under car explosion. After damage analysis during blast loads using the commercial software Autodyn, three strengthening methods are presented to improve the blast mitigation performance. The results show that the failure modes and bearing capacity are significantly different with various strengthening measures. Adhering U-shaped steel plate can effectively enhance the shear performance of PSBG under blast loads. Strengthening the bottom of the upper flange of box girder with steel plate can effectively mitigate the local bending failure, and enhance the overall flexural capacity during car explosion.

The organic coating of bridge steel girders is subjected to physical scratches, corrosion, and aging in natural weathering. The breakdown of the coating may cause serviceability and safety problems if left unnoticed. A hyperspectral imaging method is proposed to detect the condition of steel coatings based on coating-responsive features in reflectance spectra. A field test was conducted on the real-world bridge which shows obvious signs of degradation. The hyperspectral signature enables an assessment of the coating health and defect severity. The results indicated that the coating scratch can be effectively located in the domain of a hyperspectral image and the scratch depth can be determined by mapping a scratch depth indicator (SDI=R532nm / R641nm). Rust sources and products in steel girders can be identified by the unique spectral signatures and the rust stains (and thus stain areas) scattered on the coating can be pinpointed at pixel level by the corrosion rust indicators. The chemical integrity of a topcoat is demonstrated by the short-wave infrared spectroscopy and the topcoat degradation can be evaluated by the absorption at 8000 cm-1 and 5850 cm-1.

The determination of the non-loading condition of the rail cable shifting (RCS) system, which consists of main cables, hangers and rail cables, is the premise of the girder erection for the long-span suspension bridges. An analytical form-finding analysis model of shifting system is established according to the basic assumptions of flexible cable structures. Herein, the rail cable is discretized into segmental linear cable elements and the main cable is discretized into segmental catenary elements. Moreover, the calculation and analysis equation of each member and their iterative solutions are derived by taking the elastic elongation of the sling into account. In addition, by taking the girder construction of Aizhai suspension bridge as engineering background, a global scale model of the RCS system is designed and manufactured; also the test system and working conditions are established. The comparison between the test results and analytical results shows the presented analytical method is correct and effective. The process is simplified in the analytical method, and the computational results and precision can satisfy the practical engineering requirements. In addition, the proposed method is suitable to apply to the computation analysis of similar structures.

This paper uses probability method to evaluate the fire safety performance of prestressed steel-concrete beam bridges based on simulation experimental research. Firstly, fire simulation experimental sample analysis was conducted on actual small box girder bridges to obtain the structural response of prestressed steel-concrete structures under fire, which is in line with engineering practice. Next, construct a reliability analysis model for the fire resistance performance of prestressed steel-concrete beam bridges; Combining reliability theory with finite element method, establish a reliability analysis method for the fire resistance performance of prestressed steel-concrete beam bridges. Subsequently, a safety factor evaluation model for the fire resistance performance of prestressed steel-concrete beam bridges was proposed, and a safety factor evaluation method for the fire resistance performance of prestressed steel-concrete beam bridges based on reliability back analysis was established. Finally, based on the analysis of the structural response after a fire in a specific case of a simply supported to continuous prestressed steel-concrete continuous beam bridge project, a structural resistance sample of the prestressed steel-concrete beam bridge is generated through uniform design method, and statistical analysis is conducted. Subsequently, probability methods are used to evaluate the safety of the prestressed steel-concrete beam bridge after a fire. Through analysis, it can be concluded that the time of fire has a significant impact on the structural performance of prestressed steel-concrete beam bridges, and the randomness of parameters has a significant impact on the safety reserve of prestressed steel-concrete beam bridges after fire. It is necessary to pay attention to it in specific engineering practice and strengthen the monitoring and statistics of structural random characteristics.

As the general acceptance of fiber-reinforced polymer (FRP) in the concrete construction industry continues to rise, it is increasingly imperative that the crack width of FRP reinforced concrete members of pavement and girder be predicted with good accuracy due to strengthening of RC pavement, slabs or beams structures using FRP is known to control crack width. However, no specific provisions are provided by most international design codes for predicting crack width in FRP reinforced concrete flexure members. In this paper, five formulas for predicting the crack width for FRP reinforced structures are derived from three common computational theories which including statistical method, comprehensive theory, and bond-slip theory. The formula of statistical method is simplest, but the parameters depend on much sample data. The comprehensive and slippage theory based on semi-empirical statistical crack spacing are obtained through the calculation of non-uniformity coefficient of strain. The comprehensive and slippage theory based on semi-empirical axial force balance are obtained through the calculation of tensile reinforcement factor. The comparative analysis of performance of five formulas is carried out. The results indicate that the formula from comprehensive theory based on semi-empirical statistical crack spacing is recommended for predicting the crack width of FRP reinforced concrete flexural structure.

This study aimed to compare the differences in durability and prestress loss between normal-weight concrete (NC) and lightweight aggregate concrete (LWC) prestressed box girders, which were constructed at the same time in the same area, so as to verify the superiority of using synthetic lightweight aggregate (LWA) made from reservoir sediments in prestressed bridges. For the NCs and LWCs used in prestressed box girders, the basic mechanical properties were tested on the one hand, and the durability properties were tested on the other hand. Then, through the prestress monitoring system, the prestress loss of the two groups of the prestressed box girders was tracked. The results of the durability test confirmed that LWC can inhibit the penetration of air, water, and chloride ions by strengthening the interfacial transition zone between the aggregate and the cement paste, thereby improving its durability. Moreover, the magnetic flux prestress loss of the NC prestressed box girder reached 8.1%. In contrast, the magnetic flux prestress losses on both sides of the LWC prestressed box girder were 4.6% and 4.9%, respectively. This verified that, under the same environmental conditions, the use of LWC produced less of a prestress loss than the use of NC.

The average age of in-service bridges has increased in recent years in the United States. To address this issue, structural health monitoring and damage identification approaches can be employed to prioritize maintenance/replacement of aging bridges. Among the damage identification and operational health monitoring approaches, finite element (FE) model updating methods can offer a solution to evaluate the mechanics-based characteristics of bridges. However, in a real-world setting, unidentifiability and mutual dependency between model parameters, modeling errors, especially due to boundary conditions, as well as ill-conditioning of updating algorithms can pose challenges to the application of FE model updating methods. To address these challenges, this study presents a two-step FE model updating approach. In the first step, modal-based model updating is used to estimate linear model parameters mainly related to the stiffness of boundary conditions and material properties. In the second step, in order to refine parameter estimation accounting for nonlinear response behavior of the bridge, a time-domain model updating is carried out. In this step, boundary conditions are fixed at their final estimates using modal-based model updating. To prevent the convergence of updating algorithm to local solutions, the initial estimates for nonlinear material properties are selected based on their corresponding final estimates in the modal-based model updating. To validate the applicability of the two-step FE model updating approach, a series of forced-vibration experiments are designed and carried out on a pair of decommissioned and deteriorated prestressed bridge I-girders. After carrying out the two-step FE model updating, the final estimates of concrete compressive strength are shown to provide reasonable assessment of the damage extent in the girders.

In the modern construction industry, lightweight aggregate concrete (LWAC) is often used in the production of load-bearing structural members. LWAC can be up to 40% lighter by volume in comparison to normal strength concrete. On the other hand, the lack of adequate numerical models often limits the practical application of innovative building materials, such as lightweight concrete, in real projects. This trend is due to the uncertainties in design standard methods and calculation errors, the level of which is generally unacceptable to civil engineers in terms of safety and reliability. In the present paper, a comparative numerical deformation analysis of a full-scale bridge deck slab and girder has been carried out. Using the physical model proposed by the authors and the finite element software ATENA, the deformations of full–scale lightweight and traditional reinforced concrete elements under short-term effects of permanent and variable loads was compared. Depending on the safety and serviceability limit requirements, it was found that the amount of longitudinal reinforcement in lightweight reinforced concrete elements can be reduced compared to normal reinforced concrete elements with the same parameters. The results of the numerical analysis show that the deformation analysis model proposed by the authors can be a reliable tool for the design of lightweight concrete flexural members by selecting the optimum geometrical and reinforcement parameters limited by the stiffness condition.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.