This paper proposes a novel biologically inspired design for an insect-scale flapping robot. The proposed scheme employs two motors to drive four wings, mimicking the flapping motion of nat-ural four-winged insects. The vehicle incorporates two pairs of flapping wings to generate lift force, with a transmission mechanism featuring flexure hinges instead of pivot joints, resulting in reduced weight and volume. The flexure hinges also exhibit nonlinear stiffness to facilitate smooth wing motion. The vehicle is designed to be symmetrical in structure, with the wings of each section generating greater lift through the clap-and-fling mechanism. The final product weighs 6.2g, pos-sesses a wingspan of 17cm, a one-sided flapping wing angle of 103 degrees, and generates lift that exceeds its weight, attesting to its successful design.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

G4v is a four-vector theory of gravitation proposed by Mead (2015, 2023a,b) which reinterprets several major results commonly celebrated for the tensor-based approach of General Relativity (GR). Here, we show that G4v obeys the correspondence principle, an important test of any relativistic theory. We derive the non-relativistic Lagrangian and Energy expressions at the limit of low speeds and potentials, complete with the correct terms for potential energy (something traditional Special Relativity is incapable of achieving). G4v could represent a new interpretation of the gravitational field with essentially the same mathematics as electromagnetism (Mead 2023a). It is also possible to interpret G4v as a very interesting (and useful) approximation of the Einstein field equations (Mead 2023b).

Background: Parathyroid imaging techniques are used in patients with biochemically confirmed primary hyperparathyroidism (pHPT) to detect the localization of enlarged parathyroid gland(s) (PTG) and thereby to allow more focused, unilateral or minimally invasive parathyreoidectomy (PTX), instead of classical bilateral neck exploration (BNE). Although the preferred sequence of imaging continues to evolve, ultrasonography (US) is usually the first line modality, followed by 99mTc sestamibi parathyroid scan (SPS). However, both tests may have suboptimal localizing accuracy with considerable rate of non-localized cases. Therefore, more accurate four-dimensional computed tomography scan (4D-CT) has been employed for PTG imaging. Currently, there is a paucity of data evaluating the utility of 4D-CT in low case-load settings. Aim: To evaluate the impact of PTG imaging, using 4D-CT in conjunction with it’s intraoperatively displayed results, on the outcomes of surgical PTX. Our primary outcome was sensitivity of 4D-CT in comparison to US and SPS for preoperative PTG adenoma localization. The secondary outcomes were the need for redo surgery and morbidity. Additionally, the characteristics of surgical PTX, i.e. operative time, number of removed parathyroid glands, and rate of simultaneous thyroid surgery, were assessed. Methods: A single-center retrospective analysis of surgically treated patients with pHPT from 01/2010 to 01/2021 was conducted. Evaluation of impact of the preoperative imaging modalities on the results of surgical treatment was carried out. Results: During the study period 290 PTX were performed, 45 cases were excluded due to surgery for secondary, tertiary or recurrent HPT, or due to use of alternative imaging techniques; the remaining 245 patients were included in the study. US was carried out for PTG imaging in 236 (96.3%), SPS in 93 (38.0%), and 4D-CT in 52 patients (21.2%). The use of 4D-CT was associated with a significantly higher rate of successful localization of enlarged PTG (49 cases, 94.2%) compared to US and SPS (74 cases, 31.4%, and 54 cases, 58.1%, respectively). We distinguished between three groups of patients based on preoperative imaging: 1) PTG lateralization via US or SPS in 106 (43.3%) cases, 2) precise localization of PTG via 4D-CT in 49 (20.0%) patients, and 3) in 90 cases (36.7%) PTG imaging failed to localize enlarged gland. The group of 4D-CT localization had significantly shorter operative time, lower rate of simultaneous thyroid resections, as well as lower rate of removal of ≥2 PTG, compared to the other groups. The 4D-CT imaging was also associated with the lowest perioperative morbidity and with the lowest median PTH in one month follow-up; however, compared to the other groups, these differences were statistically not significant. Implementation of 4D-CT (since 01/2018) decreased the need for redo surgery (from 11.5% to 7.3%), and significantly increased the annual case load of PTX at our institution (from 15.3 to 41.0), compared to the period before 4D-CT diagnostics. Conclusions: 4D-CT imaging enabled to precisely locate almost 95% of enlarged PTG in patients with pHPT. Accurate localization and intraoperatively displayed imaging results are useful guides for surgeons in making PTX a faster and safer procedure in a low volume center.

Capabilities of the Attenuated Total Reflection (ATR) at THz wavelengths for increased sub-surface depth characterisation of (bio-)materials is presented. The penetration depth of a THz evanescent wave in biological samples is dependent on the wavelength and temperature and can reach 0.1-0.5 mm depth due to strong refractive index change ∼0.4 of the ice-water transition; this is quite significant and important when studying biological samples. Technical challenges are discussed when using ATR for uneven, heterogeneous, high refractive index samples with possibility of frustrated total internal reflection (a breakdown of the ATR reflection-mode into transmission-mode). Local field enhancements at the interface are discussed with numerical/analytical examples. Maxwell’s scaling was used to model behaviour of absorber-scatterer inside materials at the interface with ATR prism for realistic complex refractive indices of bio-materials. Modality of ATR with polarisation analysis is proposed and its principle illustrated, opening an invitation for its experimental validation. The sensitivity of the polarised ATR mode to the refractive index between the sample and ATR prism is revealed. Design principles of polarisation active optical elements and spectral filters are outlined. The results and concepts are based on experiments carried out at the THz beamline of the Australian Synchrotron.

We theoretically investigate and optimize the performance of four-wave mixing (FWM) in microring resonators (MRRs) integrated with two-dimensional (2D) layered graphene oxide (GO) films. Owing to the interaction between the MRRs and the highly nonlinear GO films as well as to the resonant enhancement effect, the FWM efficiency in GO-coated MRRs can be significantly improved. Based on previous experiments, we perform detailed analysis for the influence of the GO film parameters and MRR coupling strength on the FWM conversion efficiency (CE) of the hybrid MRRs. By optimizing the device parameters to balance the trade-off between the Kerr nonlinearity and loss, we achieve a high CE enhancement of ~18.6 dB relative to the uncoated MRR, which is ~8.3 dB higher than previous experimental results. The influence of photo-thermal changes in the GO films as well as variations in the MRR parameters such as the ring radius and waveguide dispersion on the FWM performance is also discussed. These results highlight the significantly improved FWM performance that can be achieved in MRRs incorporating GO films

Layered 2D graphene oxide (GO) films are integrated with silicon nitride (SiN) waveguides to experimentally demonstrate an enhanced Kerr nonlinearity via four-wave mixing (FWM). Owing to the strong light–matter interaction between the SiN waveguides and the highly nonlinear GO films, the FWM performance of the hybrid waveguides is significantly improved. SiN waveguides with both uniformly coated and patterned GO films are fabricated based on a transfer-free, layer-by-layer GO coating method together with standard photolithography and lift-off processes, yielding precise control of the film thickness, placement and coating length. Detailed FWM measurements are carried out for the fabricated devices with different numbers of GO layers and at different pump powers. By optimizing the trade-off between the nonlinearity and loss, we obtain a significant improvement in the FWM conversion efficiency of ≈7.3 dB for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. We also obtain a significant increase in FWM bandwidth for the patterned devices. A detailed analysis of the influence of pattern length and position on the FWM performance is performed. Based on the FWM measurements, the dependence of GO’s third-order nonlinearity on layer number and pump power is also extracted, revealing interesting physical insights about the 2D layered GO films. Finally, we obtain an enhancement in the effective nonlinear parameter of the hybrid waveguides by over a factor of 100. These results verify the enhanced nonlinear optical performance of SiN waveguides achievable by incorporating 2D layered GO films.

InGaN/GaN samples grown on c-plane sapphire substrate with different In concentrations by metal organic chemical vapor deposition are demonstrated. The subsequent capping GaN layer growth opens a possibility for dislocation reduction due to the lateral strain relaxation in growth geometry. We present the further growth optimization and innovative characterization of InGaN layers overgrown on different structures with varying In concentrations. The photoelectrical and optical properties of the InGaN layers with or without capping GaN layer were investigated by time-resolved picosecond transient grating and temperature dependence photoluminescence. We note a 10-fold increase in carrier lifetime in the InGaN layers when the sample structure changes from PIN to single InGaN layer.

The type III receptor tyrosine kinase FLT3 is a pivotal kinase for hematopoietic progenitor cell regulation, with significant implications in acute myeloid leukemia (AML) through mutations like internal tandem duplication (ITD). This study delves into the structural intricacies of FLT3, the roles of activation loop mutants, and their interaction with tyrosine kinase inhibitors. Coupled with this, the research leverages molecular contrastive learning and protein language modeling to examine interactions between small molecule inhibitors and FLT3 activation loop mutants. Utilizing the ConPLex platform, over 5.7 million unique FLT3 activation loop mutants-small molecule pairs were analyzed. The binding free energies of three inhibitors were assessed, and cellular apoptotic responses were evaluated under drug treatments. Notably, the introduction of the Xepto50 scoring system provides a nuanced metric for drug efficacy. The findings underscore the modulation of molecular interactions and cellular responses by Y842 mutations in FLT3-KD, highlighting the need for tailored therapeutic approaches in FLT3-ITD-related malignancies.

Unsmooth reversing is one of the most common faults in the four-way reversing valve of air conditioning system, and the airflow in the valve chamber and the shape of the slider of the reversing valve are the main factors in unsmooth reversing. In order to study the influence of the airflow in the chamber and the slider shape on the reversing process, the fluid flow in the valve chamber of a four-way reversing valve is obtained using computational fluid dynamics (CFD) simulations, and the influence of slider structure on slider thrust and resistance of the four-way reversing valve is analyzed. Four-way reversing valves with no-cutting, straight-cutting and arc-cutting sliders are employed to evaluate the reversing characteristics. A pressure measuring device for a four-way reversing valve chamber is designed, which is performed to test the chamber pressure of three different types of sliders of four-way reversing valves. The maximum error of experimental tests and simulations is within 5% of engineering tolerance, so as to verify the reliability of numerical simulation. The results indicate that the chamber pressure and resistance-thrust ratio with the cutting slider are reduced, which is beneficial to the reversing of the four-way reversing valve. Compared with the straight cutting structure, the arc cutting slider four-way reversing valve has a more stable reversing process and better comprehensive reversing performance. The results can provide a theoretical basis for engineers to improve the performance of four-way reversing valves.

We report photon-phonon atomic coherence (cascade- and nested-dressing) interaction from various phase transitions of Eu3+: BiPO4 crystal. Such atomic coherence spectral interaction evolves from out of phase fluorescence to in-phase spontaneous four-wave mixing (SFWM) by changing the time gate. The dressing dip switch and three dressing dips of SFWM result from strong photon-phonon destructive cross- and self-interaction for hexagonal phase, respectively. The more phonon dressing result in destructive interaction, while less phonon dressing result in constructive interaction of atomic coherences. The experimental measurements of photon-phonon interaction agree with theoretical simulations. Based on our results, we proposed a model for an optical transistor (as an amplifier and switch).

Nisin, an antibacterial compound produced by Lactococcus lactis strains, has been approved by the US Food and Drug Administration to be used as a safe food additive to control the growth of undesirable pathogenic bacteria. Nisin is commonly described as a pH-dependent primary metabolite, since its production depends on growth and culture pH evolution. However, the relationship between bacteriocin synthesis and the consumption of the limiting nutrient has not been described until now. Therefore, this study aimed to develop a competitive four-dimensional Lotka Volterra-like equation to describe the relationships between culture pH, limiting nutrient (total nitrogen: TN) consumption and production of biomass (X) and nisin (BT) in four series of batch fermentation with L. lactis CECT 539 in diluted whey (DW)-based media. The developed four-dimensional LV-like equation (with a unique set of parameters) could not be used to describe all cultures belonging to each fermentation series. However, the four-dimensional LV-like equation described accurately each individual culture, providing a good description of the relationships between pH, TN, X and BT, higher values for R2 and F-ratios, lower values (< 10%) for the mean relative percentage deviation modulus, with bias and accuracy factor values approximately equal to one.

An adaptive control technique has been implemented for DSTATCOM for power quality enhancement in three phase four wires(3P4W) distribution system. The reference source currents are extracted from active components of load current for each phase by using this technique. It has also been used for load balancing, harmonic suppression, power factor improvement and reactive power compensation in distribution system. The adaptive control technique has been tested at varying load in steady state and dynamic conditions. This technique is developed using MATLAB/Simulink and source side harmonics are mitigated under different load conditions which are acceptable in accordance with IEEE standard.

This work is devoted to the construction and study of commutative gates for a two-qubit quantum system. Using four-dimensional algebra developed by the Kazakh mathematician Abenov M.M. all groups of commutative gates have been constructed, and among all states of a two-qubit quantum system, unitary states with which a specific gate is connected have been identified. An explicit type of gate is described that transfers a quantum system from one unitary state to another unitary state. The proposed approach opens up new possibilities for the design of quantum algorithms not only for two-qubit quantum systems, but also for $n$-qubit quantum systems.

Owing to the advantages of cost-effectiveness, compactness, and the avoidance of complicated camera synchronization, single-camera three-dimensional (3D) digital image correlation (DIC) techniques have gained increasing attention for deformation measurement of materials and structures. In the traditional single-camera 3D-DIC system, the left and right view images can be recorded by a single camera using a diffraction grating, a bi-prism or a set of planar mirrors. To further improve the measurement accuracy of single-camera 3D-DIC, this paper introduces a single-camera four-view imaging technique by installing a pyramidal prism in front of the camera. The 3D reconstruction of the measured points before and after deformation is realized with eight governing equations induced by four views, and the strong geometric constraints of four views can help to improve the measurement accuracy. A static experiment, a rigid body translation experiment and a four-point bending experiment show that the proposed single-camera 3D-DIC method can achieve higher measurement accuracy than the dual-view single-camera 3D-DIC techniques and has advantages in reducing both random error and systematic error.

Guessing effects frequently occur in testing data in educational or psychological applications. Different item response models have been proposed to handle guessing effects in dichotomous test items. However, it has been pointed out in the literature that the oftenemployed three-parameter logistic model poses implausible assumptions regarding the guessing process. The four-parameter guessing model has been proposed as an alternative to circumvent these conceptual issues. In this article, the four-parameter guessing model is compared with alternative item response models for handling guessing effects through a simulation study and an empirical example. It turned out that model selection for item response models should be rather based on the AIC than the BIC. However, the RMSD item fit statistic used with typical cutoff values was found to be ineffective in detecting misspecified item response models. Furthermore, sufficiently large sample sizes are required for sufficiently precise item parameter estimation. Moreover, it is argued that the criterion of statistical model fit should not be the sole criterion of model choice. The item response model used in operational practice should be valid with respect to the meaning of the ability variable and the underlying model assumptions. In this sense, the four-parameter guessing model could be the model of choice in educational large-scale assessment studies.

The correspondence between classical and quaternion quantum equations, permits considering the universe (vacuum) as an ideal elastic solid. Elementary particles would have to be standing or soliton-like waves. Tension induced by the compression and twisting of the elastic medium would increase the energy density, consequently generate a gravity forcing and affect the wave speed. Consequently the gravity could be described by an index of refraction. Theory was created by combining the Cauchy model of the elastic continuum with the Planck-Kleinert crystal hypothesis. The quaternion-imaginary Lagrange’an, the quaternion motion equation and the quaternionic oscillator allowed deriving: - The Schrödinger equation from the functional integral, which identifies the quaternion-imaginary quantum Hamiltonian. - The 2nd order wave equation system describing both the bosons and the gravity in terms of quaternionic Poisson equation. - The first order quaternionic wave equation system. - The family of the second order wave equation systems describing both the particles and the generated quaternionic force-fields (four-potentials). - The fundamental Planck and gravity constants. - The quaternionic continuity equation in an ideal elastic solid.

We report enhanced nonlinear optics in complementary metal-oxide-semiconductor (CMOS) compatible photonic platforms through the use of layered two-dimensional (2D) graphene oxide (GO) films. We integrate GO films with silicon-on-insulator nanowires (SOI), high index doped silica glass (Hydex) and silicon nitride (SiN) waveguides and ring resonators, to demonstrate an enhanced optical nonlinearity including Kerr nonlinearity and four-wave mixing (FWM). The GO films are integrated using a large-area, transfer-free, layer-by-layer method while the film placement and size are controlled by photolithography. In SOI nanowires we observe a dramatic enhancement in both the Kerr nonlinearity and nonlinear figure of merit (FOM) due to the highly nonlinear GO films. Self-phase modulation (SPM) measurements show significant spectral broadening enhancement for SOI nanowires coated with patterned films of GO. The dependence of GO’s Kerr nonlinearity on layer number and pulse energy shows trends of the layered GO films from 2D to quasi bulk-like behavior. The nonlinear parameter of GO coated SOI nanowires is increased 16 folds, with the nonlinear FOM increasing over 20 times to FOM > 5. We also observe an improved FWM efficiency in SiN waveguides integrated with 2D layered GO films. FWM measurements for samples with different numbers of GO layers and at different pump powers are performed, achieving up to ≈7.3 dB conversion efficiency (CE) enhancement for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. These results reveal the strong potential of GO films to improve the nonlinear optics of silicon, Hydex and SiN photonic devices.

With our long experience in the field of unification of gravity and quantum mechanics, we understood that, when mass of any elementary is extremely small/negligible compared to macroscopic bodies, highly curved microscopic space-time can be addressed with large gravitational constants and magnitude of elementary gravitational constant seems to increase with decreasing mass and increasing interaction range. In our earlier publications, we proposed that, 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions; 2) There exists a strong interaction elementary charge in such a way that, it's squared ratio with normal elementary charge is close to inverse of the strong coupling constant; and 3) Considering a fermion-boson mass ratio of 2.27, quarks can be split into quark fermions and quark bosons. Further, we noticed that, electroweak field seems to be operated by a primordial massive fermion of rest energy 584.725 GeV and hadron masses seem to be generated by a new hadronic fermion of rest energy 103.4 GeV. In this context, starting from lepton rest masses to stellar masses, we have developed many interesting and workable relations. With further study, a workable model of final unification can be developed.

The characterization of thin-film solar cells is of huge importance for obtaining high open-circuit voltage and low recombination rates from the interfaces or within the bulk of the main materials. Among the many electrical characterization techniques, the two- and four-wire probe using the Cascade instrument is of interest since the resistance of the wires, and the electrical contacts can be excluded by the additional two wires in 4-wire probe configuration. In this paper, both two and four-point probes configuration are employed to characterize the CIGS chalcogenide thin-film solar cells. The two-wire probe has been used to measure the current-voltage characteristics of the cell which results in a huge internal resistance. Therefore, the four-wire connection is also used to eliminate the lead resistance to enhance the characterization’s accuracy. The load resistance in the two-wire probe diminishes the photogenerated current density at smaller voltage ranges. In contrast, the proposed four-wire probe collects more current at higher voltages due to enhanced carrier collection efficiency from contact electrodes. The current conduction mechanism is also identified at every voltage region represented by the value of the ideality factor of that voltage region. It is observed that a long time given to the charge collection results in increased current density at a higher voltage. According to the results and device characteristics, a novel double-diode model is suggested to extract the saturation current density, shunt and series resistances and the ideality factor of the cells. These cells are shown to be efficient in terms of low recombination at the interfaces and with lower series resistance as the quality of the materials is in its most possible conductive form. The measured internal resistance and saturation current density and ideality factor of the two measurement configuration is measured and compared.

The switched inertance hydraulic system (SIHS) is a novel high-bandwidth and energy-efficient digital device which can adjust or control flow and pressure by a means that does not rely on throttling the flow and dissipation of power. An SIHS can provide an efficient step-up or step-down of pressure or flow rate by using a digital control signal. In this article, analytical models of an SIHS in a four-port high-speed switching valve configuration are proposed, and the system dynamics and performance are investigated theoretically and experimentally. The flow responses, system characteristics and power consumption can be predicted effectively and accurately by using the proposed models, which were validated by comparing with experiments and with numerical simulation. The four-port configuration is compared with the three-port configuration, and it is concluded that the former one is less efficient for valves of the same size, but provides a bi-direction control capability. As bi-direction control is a common requirement, this constitutes an important contribution to the development of efficient digital hydraulics.

The reasons for the circular sense of human color perception generated by two sorts of color opponent neurons and three cone types are not well understood. Here we use geometrical analysis to examine the hypothesis that opponency, the recursive nature of color perception, and trichromacy arise as the most efficient ways of distinguishing spectrally different points on a plane using a minimum of color classes and receptor types.

This paper is concerned with a hydraulic cylinder directly controlled by a variable speed fixed displacement pump. The considered configuration is referred to as a one-motor-one-pump (1M1P) motor-controlled hydraulic cylinder (MCC). A 1M1P MCC with a hydraulically driven passive load-holding function enabled by controlled system pressures is proposed. The proposed load-holding functionality works if there is a standstill command, a loss of power supply, or a hose rupture. Additionally, this paper conducts a comprehensive analysis of the proposed system's operation and load-holding function across four quadrants. Simulation results demonstrate the four-quadrant operation and good load-holding performance under the aforementioned scenarios. In conclusion, the proposed 1M1P MCC can be successfully used on practical applications characterized by overrunning loads and four quadrant operation.

We report the use of four-layer graphene (4LG) as a highly reliable transparent conductive electrode (TCE) for polymer-dispersed liquid crystal (PDLC)-based smart window devices. The adhesion between 4LG and the substrate was successfully improved through a water-induced interface-cleaning (WIIC) process. We compared the performance of a device with a WIIC-processed 4LG electrode with that of devices with a conventional Indium tin oxide (ITO) electrode and a 4LG electrode without a WIIC. With the application of the WIIC process, the PDLC smart window with a 4LG electrode exhibited reduced turn-on voltage and haze compared to 4LG without the WIIC process and characteristics comparable to those of the ITO electrode. Based on our observations, we conclude that 4LG with WIIC is a promising TCE for flexible smart windows.

Recently, cobalt iron boron (CoFeB) thin films have been widely investigated to apply to magnetic sensors, due to their high magnetic moment, anisotropy, and stability. However, most of these studies are conducted on rigid silicon substrates. For more diverse applications of magnetic sensors and angle sensors, it is important to explore the properties of ferromagnetic thin films grown on non-rigid deformable substrates. Here, using representative deformable substrates such as polyimide (PI), polyethylene naphthalate (PEN) and polydimethylsiloxane (PDMS) that can be bent or stretched, we report experimental comparison of in-plane magnetic field angle-dependent properties of the amorphous Ta/CoFeB/MgO/Ta thin film which is grown on those deformable substrates. We investigate effects of substrate roughness, tensile stress, characteristics of deformable substrates, and sputtering process on the change of magnetic properties like coercive field (Hc), remanence over saturation magnetization (Mr/Ms), and their biaxial characteristics. This work presents unconventional foundations for exploring deformable magnetic sensors capable of detecting magnetic field angle.

We compare several different measures of non-Gaussianity for two families of four-photon superpositions of the Fock states: even vacuum squeezed states and orthogonal-even coherent states.

Layered two-dimensional (2D) graphene oxide (GO) films are integrated with micro-ring resonators (MRRs) to experimentally demonstrate enhanced nonlinear optics in the form of four-wave mixing (FWM). Both uniformly coated and patterned GO films are integrated on CMOS-compatible doped silica MRRs using a large-area, transfer-free, layer-by-layer GO coating method together with photolithography and lift-off processes, yielding precise control of the film thickness, placement, and coating length. The high Kerr nonlinearity and low loss of the GO films combined with the strong light-matter interaction within the MRRs results in a significant improvement in the FWM efficiency in the hybrid MRRs. Detailed FWM measurements are performed at different pump powers and resonant wavelengths for the uniformly coated MRRs with 1−5 layers of GO as well as the patterned devices with 10−50 layers of GO. The experimental results show good agreement with theory, achieving up to ~7.6-dB enhancement in the FWM conversion efficiency (CE) for an MRR uniformly coated with 1 layer of GO and ~10.3-dB for a patterned device with 50 layers of GO. By fitting the measured CE as a function of pump power for devices with different numbers of GO layers, we also extract the dependence of GO’s third-order nonlinearity on layer number and pump power, revealing interesting physical insights about the evolution of the layered GO films from 2D monolayers to quasi bulk-like behavior. These results confirm the high nonlinear optical performance of integrated photonic resonators incorporated with 2D layered GO films.

To understand the mystery of final unification, in our earlier publications, we proposed that there exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions. During cosmic evolution, if one is willing to give equal importance to Higgs boson and Planck mass in understanding the massive origin of elementary particles, then it seems quite logical to expect a common relation in between Planck scale and Electroweak scale. Based on these two points, we noticed that, electroweak field seems to be operated by a primordial massive fermion of rest energy 585 GeV. It can be considered as the zygote of all elementary particles and galactic dark matter. H-bar seems to be a characteristic outcome of unified electroweak gravity. Electron rest mass seems to be a characteristic outcome of electroweak and strong gravity. Proton rest mass seems to be a characteristic outcome of electroweak, strong and electromagnetic gravity. Recently observed 3.5 keV photon seems to be an outcome of annihilation of charged baby lepton of rest energy 1.75 keV. Interesting point to be noted is that, Schwarzschild radius of electron is 0.48 nanometer and it needs further investigation with respect to emerging nano-science and technology. Proceeding further, by considering electromagnetic and weak gravitational constants, neutron life time can be understood.

An investigation was made to determine the effects of tungsten surface coating on the coefficient of friction of sliding contact between lubricated steel surfaces. The four-ball test was modified, using a tungsten carbide ball bearing in the spindle to cause sliding contact onto three hard steel ball bearings coated with tungsten disulfide lamellar dry lubricant coating, with a coating of grease lubrication applied to the ball bearings. The coatings, loads, speed, and grease level was varied to best understand the impact of different conditions to the friction coefficient.

We review some recent developments about strongly interacting relativistic Fermi theories in three spacetime dimensions. These models realize the asymptotic safety scenario and are used to describe the low-energy properties of Dirac materials in condensed matter physics. We begin with a general discussion of the symmetries of multi-flavor Fermi systems in arbitrary dimensions. Then we review known results about the critical flavor number $N_\mathrm{crit}$ of Thirring models in three dimensions. Only models with flavor number below $N_\mathrm{crit}$ show a phase transition from a symmetry-broken strong-coupling phase to a symmetric weak-coupling phase. Recent simulations with chiral fermions show that $N_\mathrm{crit}$ is smaller than previously extracted with various non-perturbative methods. Our simulations with chiral SLAC fermions reveal that for four-component flavors $N_\mathrm{crit}=0.80(4)$. This means that all reducible Thirring models with $\Nr=1,2,3,\dots$ show no phase transition with order parameter. Instead we discover footprints of phase transitions without order parameter. These new transitions are probably smooth and could be used to relate the lattice Thirring models to Thirring models in the continuum. For a single irreducible flavor, we provide previously unpublished values for the critical couplings and critical exponents.

Protein-protein interactions (PPIs) are associated with various diseases; hence, they are important targets in drug discovery. However, the physicochemical empirical properties of PPI-targeted drugs are distinct from those of conventional small molecule oral pharmaceuticals, which adhere to the ”rule of five (RO5).” Therefore, developing PPI-targeted drugs using conventional methods, such as molecular generation models, is difficult. In this study, we propose a molecule generation model based on deep reinforcement learning, specialized for generating PPI inhibitors. By introducing a scoring function that can represent the properties of PPI inhibitors, we successfully generated potential PPI inhibitor compounds. The generated virtual compounds possess the desired properties for PPI inhibitors, and show similarity to commercially available PPI libraries. These generated virtual compounds are freely available as a virtual library.

A new method in which completely eliminated the negative value of the scattering power is proposed in this paper. Primarily, here are presented the Freeman-Durden decomposition of the scattering powers, which are computed by using the coherency matrix elements with rotation and without rotation. Secondly, this paper investigates the reasons of the occurrence of negative values of the scattering powers. Then using the modification like in algorithm proposed by Yamaguchi for G4U, it was applied for the algorithm of Freeman-Durden decomposition to eliminate negative values. In this research, Radarsat-2 radar remote sensing data were used, which are acquired for study area Yushu County, Qinghai province, China. At the end, the comparison results of Yamaguchi G4U and a modified Freeman-Durden decompositions were presented.

In this study, we actually want to explore the time-fractional Phi-four equation via two methods, the exp _a function method and the hyperbolic function method. We transform a fractional order dierential equation into an ordinary differential equation using a wave transformation and the fractional derivative in conformable form. Then, the resulting equation has successfully been explored for new explicit exact solutions. The procured solutions are simply showed the effectiveness and plainness of the projected methods.

Progressive supranuclear palsy (PSP) is a sporadic parkinsonism tauopathy characterised by the deposition of aggregations of abnormal, hyperphosphorylated four-repeat tau (4R-tau). A revised clinical diagnostic criterion for PSP allows early presentations for the full spectrum of clinical phenotypes to be recognised enabling doctors to make a more accurate diagnosis. The major genetic risk factor for sporadic PSP is a common variant in the gene encoding microtubule-associated protein tau (MAPT). Research into the biochemical and pathological pathways of tau is vital to improve the chances of developing an effective diagnostic biomarker to monitor tau pathogenesis. Neuroimaging biomarkers, such as tau PET ligands, are proving the most successful tool in providing a differential diagnosis between neurodegenerative disorders. There are currently no effective treatments for PSP, however tau-directed therapies in the last five years have rapidly advanced. Latest tau therapies are proposed to have disease-modifying effects by reducing toxic aggregations of tau through manipulating tau gene expression. After encouraging results from long awaited trials, additional funding is being injected into this field and with new results expected, this proves an exciting area for scientific discovery. This paper reviews advances in pathophysiology, diagnosis, biomarkers and disease-modifying therapeutic treatments for PSP.

This paper presents a novel real time control strategy on four-wheel independent steering system for electric vehicle with stepper motors using neural networks combined with fuzzy logic. The control of the four wheels is based on a variation of Hopfield Neural Network (VHNN) method, in which the input is the error of each steering motor and the output is processed by a hyperbolic tangent function (HTF) feeding the fuzzy logic controller (FLC), which ultimately drives the stepper motor. The whole system is made up of the four aforementioned blocks where they work in sync and inseparable from each other with the common goal of driving all the steering stepper motors at the same time. Simulation results demonstrate that the proposed control method has strong robustness and practicability under different angles and speeds.

This article describes the transition of an undirected active network, used for numerical and logical analysis, and made up of communicating operators and nodes, and being self-extensible, into a network of semantic structures, and the extensions necessary to handle language. The network, called Active Structure, was infused with knowledge in the form of tens of thousands of definitions taken from a human-readable dictionary. Where the dictionary fell short, from circularity, lack of a hierarchical form for its senses and sub senses, or inadequate detail around verbs, the entries were extensively curated. The result is a machine which has access to every meaning of every word in its vocabulary, and needs to manage the right meaning for every use of a word, a task that our unconscious minds now handle. To demonstrate that such a network can aspire to human-level tasks, we have begun loading an Anti-Money Laundering Act so that the machine can devise and test strategies against money launderers. There is a higher goal being aimed at, the breaking of the Four Pieces Limit. That is, the network is not intended to save money on human cognitive labor, but to raise an absurdly low limit on it.

To understand the mystery of final unification, in our earlier publications, we proposed that, 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions; and 2) There exists a strong interaction elementary charge (e_s) in such a way that, it's squared ratio with normal elementary charge is close to inverse of the strong coupling constant. In this context, starting from lepton rest masses to stellar masses, we have developed many interesting and workable relations. We noticed that, electroweak field seems to be operated by a primordial massive fermion of rest energy 585 GeV. It can be considered as the zygote of all elementary particles and galactic dark matter. Proceeding further, with a characteristic fermion-boson mass ratio of 2.27, quarks can be classified into quark fermions and quark bosons. Considering strong charge conservation and electromagnetic charge conservation, fractional charge quark fermions and quark bosons can be understood. Quark fermions that generate observable massive baryons can be called as Fluons. Quark bosons that generate observable mesons can be called as Bluons. By considering a new hadronic fermion of rest energy 103.4 GeV, rest masses of fluons and bluons can be estimated and there by baryon masses and meson masses can be estimated.

The theory of special relativity has reexamined and reconstructed the concepts of space and time, which are indispensable for describing physical laws, consequently instigating a major revolution in physics in general. Although the correctness of the special theory of relativity has been con-firmed by many observations and experiments, it is unclear why the "principle of relativity" and the "principle of the constant speed of light," which form the basis of the idea, are valid. Moreo-ver, although special relativity has advanced our understanding of time, our understanding of the fundamental question, "What is time?" is still limited. The theory of special relativity regards space as a four-dimensional construct consisting of one-dimensional time and three-dimensional space. This paper proposes an alternative framework, wherein real space is uniform and isotropic four-dimensional space, and elementary particles are waves that propagate through this four-dimensional space at a constant speed. This new perspective provides evidence to support two of Einstein’s key principles—the "principle of relativity" and the "principle of the constant speed of light." Furthermore, this model clarifies what time is and why time flows at a constant rate from the past to the future.

To understand the mystery of final unification, in our earlier publications, we proposed two bold concepts: 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions. 2) There exists a strong elementary charge in such a way that its squared ratio with normal elementary charge is close to reciprocal of the strong coupling constant. In this paper we propose that, can be considered as a compound physical constant associated with proton mass, electron mass and the three atomic gravitational constants. With these ideas, an attempt is made to understand nuclear stability and binding energy. In this new approach, nuclear binding energy can be fitted with four simple terms having one unique energy coefficient with a formula, where is an estimated mean stable mass number. With this new approach, Newtonian gravitational constant can be estimated in a verifiable approach with a model relation of the form, where is the Fine structure constant. Estimated and is 62 ppm higher than the CODATA recommended It needs further investigation. Proceeding further, an attempt is made to fit the recommended quark masses.

An attempt is made to model the atomic nucleus as a combination of bound and free or unbound nucleons. Due to strong interaction, bound nucleons help in increasing nuclear binding energy and due to electroweak interaction, free or unbound nucleons help in decreasing nuclear binding energy. In this context, with reference to proposed 4G model of final unification and strong interaction, recently we have developed a unified nuclear binding energy scheme with four simple terms, one energy coefficient of 10.1 MeV and two small numbers 0.0016 and 0.0019. In this paper, by eliminating the number 0.0019, we try to fine tune the estimation procedure of number of free or unbound nucleons pertaining to the second term with an energy coefficient of 11.9 MeV. It seems that, some kind of electroweak interaction is playing a strange role in maintaining free or unbound nucleons within the nucleus. It is possible to say that, strong interaction plays a vital role in increasing nuclear binding energy and electroweak interaction plays a vital role in reducing nuclear binding energy. Interesting observation is that, Z can be considered as a characteristic representation of range of number of bound isotopes of Z. For medium, heavy and super heavy atoms, beginning and ending mass numbers pertaining to bound states can be understood with 2Z+0.004Z^2 and 3Z+0.004Z^2 respectively. With further study, neutron drip lines can be understood. Based on this kind of data fitting procedure and by considering the mass ratio of pions and electroweak bosons, existence of our 4G model of electroweak fermion of rest energy 584.725 GeV can be confirmed confidently.

The genetic code evolved around the reading of the tRNA anticodon on the primitive ribosome, and tRNA-34 wobble and tRNA-37 modifications coevolved with the code. We posit that EF-Tu, the closing mechanism of the 30S ribosomal subunit, methylation of wobble U34 at the 5-carbon and suppression of wobbling at the tRNA-36 position were partly redundant and overlapping functions that coevolved to establish the code. The genetic code devolved in evolution of mitochondria to reduce the size of the tRNAome (all of the tRNAs of an organism or organelle). “Superwobbling” or four-way wobbling describes a major mechanism for shrinking the mitochondrial tRNAome. In superwobbling, unmodified wobble tRNA-U34 can recognize all four codon wobble bases (A, G, C and U), allowing a single unmodified tRNA-U34 to read a 4-codon box. During code evolution, to suppress superwobbling in 2-codon sectors, U34 modification by methylation at the 5-carbon position appears essential. As expected, at the base of code evolution, tRNA-37 modifications mostly related to the identity of the adjacent tRNA-36 base. TRNA-37 modifications help maintain the translation frame during elongation.

A method for generating fluoroscopic (time-varying) volumetric images using patient-specific motion models derived from 4-dimensional cone-beam CT (4D-CBCT) images is developed. 4D-CBCT images acquired immediately prior to treatment have the potential to accurately represent patient anatomy and respiration during treatment. Fluoroscopic 3D image estimation is done in two steps: 1) deriving motion models and 2) optimization. To derive motion models, every phase in a 4D-CBCT set is registered to a reference phase chosen from the same set using deformable image registration (DIR). Principal components analysis (PCA) is used to reduce the dimensionality of the displacement vector fields (DVFs) resulting from DIR into a few vectors representing organ motion found in the DVFs. The PCA motion models are optimized iteratively by comparing a cone-beam CT (CBCT) projection to a simulated projection computed from both the motion model and a reference 4D-CBCT phase, resulting in a sequence of fluoroscopic 3D images. Patient datasets were used to evaluate the method by estimating the tumor location in the generated images compared to manually defined ground truth positions. Experimental results showed that the average tumor mean absolute error (MAE) along the superior-inferior (SI) direction and the 95th percentile in two patient datasets were (2.29 mm and 5.79 mm) for patient 1 and (1.89 mm and 4.82 mm) for patient 2. This study has demonstrated the feasibility of deriving 4D-CBCT-based PCA motion models that have the potential to account for the 3D non-rigid patient motion and localize tumors and other patient anatomical structures on the day of treatment.

A revitalized practice of natural philosophy can help people to live a better life and promote a flourishing ecosystem. Such a philosophy is natural in two senses. First, it is natural by seeking to understand the whole of nature, including mental phenomena, In particular, a comprehensive natural philosophy should address the phenomena of sentience by embracing first- and second-person methods of investigation. Moreover, to expand our understanding of the world, natural philosophy should embrace a full panoply of explanations, similar to Aristotle’s four causes. Second, such a philosophy is natural by being grounded in human nature, taking full account of human capacities and limitations. Future natural philosophers should also make use of all human capacities, including emotion and intuition as well as reason and perception, to investigate nature. Finally, since the majority of our brain's activities are unconscious, natural philosophy should explore the unconscious mind with the aim of deepening our relation to the rest of nature and enhancing well-being.

This article lays the foundation for Extended Relativity (ER) – a unified geometric approach to the electromagnetic and gravitational field and relativistic dynamics in them. We explain here the basic tenets of ER, including the influenced spacetime of an object and the Extended Principle of Inertia. These two new ideas enable a unified theory of these fields. We introduce local scaling functions for describing the geometry of a spacetime influenced by a field and construct a simple, universal local scaling function which unifies electromagnetism and gravity. We recover the full electromagnetic theory, including Maxwell’s equations. For gravitation, ER passes all of the tests of General Relativity. Despite the non-linearity of relativistic gravitation, we obtain a method of combining fields from multiple sources. Finally, we identify the differences in the relativistic treatment of the electromagnetic field by Special Relativity and of the gravitational field by General Relativity and indicate how these differences are resolved in ER.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its Bring-Jerrard binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

This paper offers a novel geometric and visual approach to the renowned Four Color Map Theorem and K5 non-planarity problem while unveiling their profound connection to the "kissing number" problem in 2D. We represent planar graphs through circles and tangents, simplifying complex structures and shedding light on these classic problems. Our proofs by contradiction, rooted in the kissing number concept, reveal that both the Four Color Map Theorem and K5 non-planarity are fundamentally linked, as they pivot around the concept of coloring. This study bridges the realms of geometry and graph theory, providing fresh insights and emphasizing the significance of the kissing number problem in various fields.