Jumping side volley has created breathtaking moments and cherished memories for us. Regrettably, a scientific study on the skill has not been found in literature. Relying on talent of athletes to improvise on the fly can hardly be considered a viable learning strategy. This study targets to fill the gap by quantifying factors contributing to develop its coaching method. Using 3D motion capture (12-cameras, 200Hz) and full-body biomechanical modeling, our study aimed to identify elements that govern entrainment of the skill by examining jumping, kicking and falling phases of its execution. Given the rarity of players who have acquired this skill, we found five subjects for the study. Twenty-three trials were captured and quantified. The results unveil the following key elements: 1) the control of trunk rotation during the jumping, 2) the angle between thighs upon take-off, 3) the whip-like control of the kicking leg during airborne, 4) timing between ball motion and limbs’ coordination, and 5) damping mechanism during falling. An accurate kick can only be achieved through repetitive training. This underlines the need for athletes to master a safe landing technique that minimizes risk of injury during practice. Therefore, training should begin with learning a safe falling technique.

Directional Modulation (DM) technique, as an emerging promising approach to secure wireless communications, has been attracting increasing attention for its unique characteristic in the past decade. The baseband signal is synthesized at the antenna level for maintaining the standard constellation format along the prescribed direction(s) while simultaneously distorting the signal constellations in other undesired directions. In this paper, we present a novel DM signal synthesis method based on phased array using a hybrid genetic algorithm (GA) and particle swarm optimization (PSO) algorithm, which takes advantages of both GA and PSO algorithm. Then, the bit error rate of the proposed method is analyzed and simulated. Simulation results are presented to verify that the proposed DM signal have a narrower information beam-width. Therefore, it can offer a better physical layer security (PLS) performance compared with the conventional directional modulation signal.

Polymer composites with high thermal conductivity have a great potential for applications in modern electronics due to their low cost, easy process, and stable physical and chemical properties. Nevertheless, most polymer composites commonly possess unsatisfactory thermal conductivity, primarily because of the high interfacial thermal resistance between inorganic fillers. Herein, we developed a novel method through silver functionalized graphene nanosheets (GNS) and multiwalled carbon nanotube (MWCNT) composites with excellent thermal properties to meet the requirements of thermal management. The effects of composites on interfacial structure and properties of the composites were identified, and the microstructures and properties of the composites were studied as a function of the volume fraction of fillers. An ultrahigh thermal conductivity of 12.3 W/mK for polymer matrix composites was obtained, which is an approximate enhancement of 69.1 times compared to the polyvinyl alcohol (PVA) matrix. Moreover, these composites showed more competitive thermal conductivities compared to untreated fillers/PVA composites applied to the desktop central processing unit, making these composites a high-performance alternative to be used for thermal management.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

The CuCrSn alloy is promising as high-strength and high-conductivity Cu alloy due to its relative low smelting requirement, while thus far reports on the CuCrSn alloy is still quite lacked. In this study, the microstructure and properties of Cu-0.20Cr-0.25Sn (wt%) specimens prepared under different rolling and aging combinations were comprehensively characterized, in order to reveal the effects of cold rolling and aging on the CuCrSn alloy. The results show that increasing the aging temperature from 400 ºC to 450 ºC can obviously accelerates the precipitation, and the cold rolling before aging significantly increases the initial microhardness and promotes the precipitation. Whereas, the deformation hardening will be eliminated during the aging process, making the microhardness even decrease monotonically when the aging temperature and the rolling ratio before aging are high. Performing the cold rolling after the aging can maximize the effects of precipitation strengthening and deformation strengthening, and its adverse impact on the conductivity is not serious. A tensile strength of 506.5 MPa and a conductivity of 70.33% IACS were obtained with such a treatment, only the elongation decreases. Different strength-conductivity combinations of the CuCrSn alloy can be achieved through appropriate combinations of the aging and post aging cold rolling conditions.

In order to study the influence of falling rock shape on its rolling characteristics and realize the optimization of falling rock protection design, the following research was carried out. Design model experiments to explore the rolling characteristics of different shapes of rockfalls. Based on the experimental results, it was found that the slenderness ratio, center of gravity, and rotational inertia of the rockfalls can affect their rolling characteristics, leading to swaying and changing the rolling axis during the rolling process, thereby affecting their rolling speed. On this basis, the formation mechanism of rolling resistance is analyzed, and the main cause of energy loss is the rolling resistance arm formed with the rolling surface during rockfall rolling, and a shape parameter to quantify the rolling resistance is proposed. The parameters are substituted into the kinematic formula, in which the influence of the rockfall shape, slope and slope roughness on the rolling speed is considered. Combined with the offset and initial position of the rockfall, the formula can be used to calculate the rolling speed and impact energy in the rolling region and any position in the region. The calculation formula was validated using model experimental data, and the results showed that the error between the experimental and calculated values was small. The error was corrected based on the experimental data. After on-site testing and verification, it can provide reference for the management of rockfall disasters.

Abstract: Chronic Obstructive Pulmonary Disease (COPD) is a continually advancing respiratory disorder, characterized by enduring airflow limitation along with long-lasting inflammation in the airways. An expanding pool of evidence is emphasizing how mitochondrial dysfunction directly impacts the development and progression of COPD. This comprehensive review delves deeper into the intricate cellular and molecular biology of mitochondria within the framework of COPD, spotlighting significant alterations in structure and function that accompany mitochondrial dysfunction. In this narrative, we delve into the observed changes in mitochondrial shape, behavior, and respiratory chain complex alterations seen in individuals afflicted with COPD. The discussion includes implications on cellular signaling pathways and how this affects the natural process of programmed cellular death (apoptosis) and cellular aging, particularly in reference to COPD. Additionally, we consolidate ongoing therapeutic strategies, honing in on the management of COPD through a focus on mitochondrial dysfunction. Prominent among these strategies is the potential role of antioxidants and mitochondrial biogenesis inducers, which are emerging as promising fields of intervention. Furthermore, we embark on an overview of the possible use of mitochondrial biomarkers as innovative tools in diagnosing COPD, evaluating disease progression, and monitoring the efficacy of COPD treatments. As we unravel the rather complex interplay between mitochondrial biology and COPD, this review highlights the critical importance of formulating treatments that target mitochondrial dysfunction. The ultimate goal of these strategic interventions is to slow down the rate of COPD progression and significantly improve patient outcomes. Lastly, though our understanding of the nexus between COPD and mitochondrial dysfunction has significantly enhanced, ample scope remains for further investigation. Improved insights into the mechanisms of mitochondrial dysfunction, discovered biomarkers, and targeted therapies could encompass a revolutionary step towards comprehensive disease management. The future of COPD treatment seems to lean towards a combination of strategies, prioritizing not only the management of symptoms but also focused on preserving and restoring lung function, improving physical capacity, and enhancing quality of life for COPD patients.

Starch being renewable and biodegradable is a viable resource for developing sustainable and environmentally friendly materials. This work explores the potential of starch/Ca2+ gels based on waxy corn starch (WCS), normal corn starch (NCS), and two high-amylose corn starches, G50 (55% amylose content) and G70 (68% amylose content) as flame-retardant adhesives. Being stored at 57% relative humidity for up to 30 days, the G50/Ca2+ and G70/Ca2+ gels are stable without water absorption or retrogradation. The starch gels with increasing amylose content displayed increased cohesion, as reflected by significantly higher tensile strength and fracture energy. All the four starch-based gels show good adhesive properties on corrugated paper. For wooden boards, because of the slow diffusion of the gels, the adhesive abilities are weak initially but improve with storage extension. After storage, the adhesive abilities of the starch-based gels are almost the same except for G70/Ca2+, which is peeled off from the wood surface by itself. Moreover, all the starch/Ca2+ gels exhibit excellent flame retardancy with limiting oxygen index (LOI) values all around 60. This work demonstrates a facile method to prepare starch-based flame-retardant adhesives simply by gelating starch with a CaCl2 solution, which can be used in paper or wood products.

The human serotonin transporter (hSERT) terminates neurotransmission by removing serotonin from the synaptic cleft, which is an essential process plays an important role in depression. In addition to substrate serotonin, hSERT is also the target of drugs of abuse like cocaine and clinically used antidepressants such as escitalopram and paroxetine. To date, few studies attempt to investigate the unbinding mechanism underlying the orthosteric and allosteric modulation of hSERT. The high-resolution X-ray structure of hSERT resolved recently enables us to theoretically study the unbinding of the above four ligands against the S1 or S2 site of hSERT, by means of molecular docking, molecular dynamics (MD) and potential of mean force (PMF) simulations. We proved that for either the S1 or S2 site, the other three ligands (cocaine, escitalopram and paroxetine) are much more favorable than the original substrate serotonin, whether in kinetics along the unbinding pathways or in thermodynamics at the equilibrium states. Furthermore, the S1 site is much more favorable than the S2 site, for each ligand. Interestingly, inspection revealed that there are ~ 3Å lengths between the allosteric site of serotonin and cocaine, and an unseen un-binding pathway for escitalopram at the S1 site except for verification of the broadest trail.

Chronic obstructive pulmonary disease (COPD) patients are particularly susceptible to respiratory infections like influenza, which exacerbate symptoms and increase healthcare utilization. While smoking cessation and influenza vaccination are recommended preventive measures, their combined impact on healthcare resource utilization is underexplored. The Charlson Comorbidity Index (CCI) assesses comorbidity burden in COPD patients and may influence healthcare outcomes. We conducted a retrospective analysis of 357 COPD patients, evaluating smoking cessation success over one year and influenza vaccination receipt, stratifying patients by CCI scores. Healthcare utilization outcomes included emergency room visits, hospitalizations, and medical expenses. Results showed that 51.82% of patients quit smoking and 59.66% received influenza vaccination, with higher comorbidity prevalence in advanced COPD stages (p=0.002). Both smoking cessation and influenza vaccination independently correlated with decreased emergency room visits, hospital admissions, days, and costs. Patients who both quit smoking and received influenza vaccination exhibited the lowest healthcare utilization rates. In conclusion, smoking cessation and influenza vaccination significantly reduce healthcare resource utilization in COPD patients, with the combination yielding synergistic benefits, particularly in those with lower CCI scores. Integrating these interventions and comorbidity management in COPD strategies is essential for optimizing patient outcomes and healthcare efficiency.

To achieve a fast testing on barrier properties of organic coatings, immersion test, AC-DC-AC test, and coupled test of AC-DC-AC with hydrostatic pressure were conducted in seawater for a glass flake epoxy coating. Electrochemical impedance spectroscopy (EIS) was used to characterize the degradation processes of the coating during the tests, and the surface of the coating was analyzed using optical microscope, scanning electron microscope (SEM) and Fourier transform infrared spectrometer (FTIR). The results show that the periodically cathodic polarization coupled with high hydrostatic pressure can accelerate the degradation of the coating by facilitating the diffusion and uptake of electrolyte and the delamination of the coating. The coupled test method has the largest acceleration due to the synergetic effect of AC-DC-AC and hydrostatic pressure.

Background: Pediatric ureteropelvic junction obstruction (UPJO) is a common urinary tract issue. Accurate assessment of postoperative kidney function is crucial for prognosis. Previous studies mainly focused on postoperative renal function and individual factors. Radionuclide imaging was costly and unsuitable for long-term follow-up. For aligning closely with clinical needs, we emphasizing renal morphology enhancement, and comprehensively analyzed factors influencing UPJO surgery outcomes. Methods: We retrospectively studied 150 pediatric UPJO patients (July 2012-July 2022) with severe anteroposterior renal pelvis dilation (APD grades 4-5) who underwent laparoscopic dismembered pyeloplasty. Demographics, symptoms, preoperative findings, and postoperative renal ultrasounds were assessed. We performed multivariable logistic regression analysis to identify significant predictors of prognosis and construct a regression model. Results: Among the 150 pediatric patients, 78 (52%) showed improvement in renal morphology after surgery. In the multivariate logistic regression analysis, age at surgery, duration of hydronephrosis, body weight, and preoperative creatinine were identified as significant prognostic factors for postoperative outcomes. The nomogram (AUC: 0.92) was constructed based on these factors and could serve as a useful tool for clinicians in evaluating the surgical prognosis of children with UPJO. Conclusions: This study reveals that among pediatric patients with severe hydronephrosis resulting from UPJO, those who are younger, have a shorter duration of illness, normal serum creatinine levels, and a healthy body weight tend to experience better postoperative recovery. This finding emphasizes the importance of adopting more proactive clinical interventions when managing such cases, with the goal of achieving enhanced recovery outcomes for affected children.

In this perspective, we identify emerging frontiers in clinical and basic research of melanocyte biology and its associated biomedical disciplines. We describe challenges and opportunities in clinical and basic research of normal and diseased melanocytes that impact current approaches to research in melanoma and the dermatological sciences. We focus on four themes: (1) clinical melanoma research, (2) basic melanoma research, (3) clinical dermatology, and (4) basic pigment cell research, with the goal of outlining current highlights, challenges, and frontiers associated with pigmentation and melanocyte biology.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.