Cylindrical Fe-6.5wt.% Si bars with 7.5 mm in diameter were successfully fabricated from as cast ingot through three rolling stages within 10 passes: rough rolling at 850–900 °C and 8–10 m/min, medium rolling at 800–850 °C and 10–15 m/min, and finish rolling at 800–850 °C and 12–18 m/min. The evolution of microstructure, texture and ordered structure, and the mechanical property are investigated. The results showed that the grains were refined by the hot bar rolling. Area fractions of the {100}<011> oriented grains and the {011}<100> oriented grains decreased to 0 during the hot bar rolling. Whereas, the {100}<001> component, the {011}<211> component and the {112}<110> component increased, and γ fiber with {111}<110> component was dominant. DO₃ ordered phase were suppressed, and B2 ordered domains were refined after the hot bar rolling. Ductility of the as rolled bar was higher than that of the rotary swaged bar, due to the absence of the DO₃ ordered phase and the fine grains in the rolled bar. Hence, the hot bar rolling technology is an excellent process to fabricate the Fe-6.5wt.% Si bars.

The flow behavior of Fe-6.5wt.%Si alloys during hot compression was investigated at temperatures 650–950 °C and strain rates 0.01–10 s^-1. The results showed that the flow stress depended distinctly on the deformation temperatures and strain rates. The flow stress and work hardening rate increased with the decrease of temperature and the increase of strain rate. The activation energy under all the deformation conditions was calculated to be 410 kJ/mol. The constitutive equation with hyperbolic sine function and Zener–Hollomon parameter was developed. The peak stress, critical stress, and steady-state stress could be represented as σ=A+Bln(Z/A). Dynamic recrystallization occurred under the deformation conditions where the values of Z were lower than 10²⁰. Processing maps were established to optimize the processing parameters. The power dissipation efficiency decreased in the high temperature and low strain rate region, increased in the high temperature and high strain rate region, and remained unchanged in other regions with the increase of true strain. Furthermore, the unstable area expanded. The true strain of 0.7 was the optimum reduction according to the processing map. Based on the analysis of surface quality, microstructures, and ordered structures, the optimized processing parameters for the Fe-6.5wt.%Si alloys were the temperature and strain rate of higher than 900 °C and 0.01–10 s^-1, respectively, or 800–900 °C and lower than 0.4 s^-1, respectively.

The microstructures and mechanical properties of the hot-rolled Fe-6.5wt.%Si sheet are analyzed. The microstructure of the hot-rolled sheet is layered along the thickness direction. The surface exhibits fine and equiaxed grains, whereas the center part shows coarse and elongated grains with a <101> fiber texture along the rolling direction. Serrated flow behavior is observed during tensile deformation of both the hot-rolled sheet and its center samples at 350 °C; thus, the serrated flow of the hot-rolled sheet is mainly attributed to the serration of the center part. The analyses of dislocation configurations, ordered structures, and crystal orientation show that the serrated flow behavior results from the interaction of solutes with mobile dislocations. Mobile dislocations are pinned by combining parallel forest dislocations with the pipe diffusion of solution atoms. This study provides a new perspective for the deformation mechanism of the Fe-6.5wt.%Si alloy.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

Ultra-thin Fe–6.5wt.%Si ribbons with 35 μm in thickness were prepared by melt-spinning. The magnetic properties were investigated before and after annealing 1000 ºC. DC properties and low-frequency (400 Hz ~ 10 kHz) iron losses have significantly improved after heat treatment. A simplified formula based on Steinmetz law which can be used to predict the AC iron loss is presented. According to the results of some iron losses data, a simplified formula has been determined, and the extent of AC iron losses can be predicted. The results obtained from the formula predict AC iron loss to a good degree. The method developed in this work could be extended to other magnetic materials for predicting AC iron loss with greater ease.

Thermal analysis of a hypereutectic Al-Si alloy used for an automotive part was carried out in this research work. Solidification characteristics are recognized from the Temperature-time curve and its corresponding derivatives. This analysis was successfully used in a simulation software program with the aim of improving the resultant simulation accuracy. In this study, different types of molds, with and without cooling systems, were designed and used. The melt present in the furnaces of the factory was used to simulate the casting process. The effect of different cooling rates (1.2ºC/s, 2ºC/s, 2.3ºC/s and 2.9ºC/s) on the solidification parameters have been investigated. Differences in the resultant microstructure between wall and center of the molds have been analyzed and have been related to the T-t curve. Finally, the experimental results clearly indicate that the water-cooling rate of the molds and the melt temperature directly affects the solidification process as well as the final microstructure.

The design of processing routes involving the presence of the liquid phase is mainly associated with the knowledge of its surface and transport properties. Despite this need, due to experimental difficulties related to high temperature measurements of metallic melts, for many alloy systems neither thermodynamic nor thermophysical properties data are available. A good example lacking these datasets represents the Ir-Si system, although over the last fifty years, the structures and properties of its solid phases have been widely investigated. To compensate the missing data, the Gibbs free energy of mixing of the Ir-Si liquid phase was calculated combining the model predicted values for the enthalpy and entropy of mixing using Miedema’s model and Free Volume Theory, respectively. Subsequently, in the framework of statistical mechanics and thermodynamics, the surface properties were calculated using the Quasi Chemical Approximation (QCA) for the regular solution, while to obtain the viscosity, the Moelwyn-Hughes (MH) and Terzieff models were applied. Subsequently, the predicted values of the abovementioned thermophysical properties were used to model the non-reactive infiltration isotherm of Ir-Si (eutectic) / SiC system.

Among the thermophysical properties, the surface / interfacial tension, viscosity and density / molar volume of liquid alloys are the key properties for the modelling of microstructural evolution during solidification. Therefore, only reliable input data can yield accurate predictions preventing the error propagation in numerical simulations of solidification related processes. Due to experimental difficulties related to reactivity of metallic melts at high temperatures, the measured data are often unreliable or even lacking. The application of containerless processing techniques either leads to a significant improvement of the accuracy or makes the measurement possible at all. On the other side, accurate model predicted property values could be used to compensate the missing data; otherwise, the experimental data are useful for the validation of theoretical models. The choice of models is particularly important for the surface, transport and structural properties of liquid alloys representing the two limiting cases of mixing, i.e. ordered and phase separating alloy systems. To this aim, the thermophysical properties of the Fe-Si and Cu-Pb systems were analysed and the connections with the peculiarities of their mixing behaviours are highlighted.

The principal main of this research work was the study the influence of Cu addition on the wear behavior (WB) of eutectic Al-12.6Si alloy developed by spray forming (SF) method and compared with as-cast (AC) alloys. The phases of chemical compositions and microstructure were studied by optical microscopy, energy dispersive spectroscopy (EDS) and Scanning Electron Microscopy (SEM). The microstructure of SFAl-12.6Si (SF1) alloy reside — of fine primary and eutectic Si phases evenly distributed in the equiaxed α-Al matrix and SF Al-12.6Si-2Cu (SF2) alloy lie of uniformly distributed fine eutectic Si particulates and spherical form θ-Al2Cu precipitates in α-Al matrix. On other hand, the AC Al-12.6Si alloy (AC1) alloy involve of eutectic Si needles in the dendrite α-Al matrix, whereas AC Al-12.6Si-2Cu (AC2) alloy consisted of eutectic Si needles and Chinese script form θ phase distributed randomly in the α-Al matrix. The microhardness and wear properties were analyzed using Vickers hardness (VH) and dry sliding WT. The SF alloys exhibit superior hardness compared to the AC alloys. The wear properties of SF alloys exhibited significantly superior compared to the AC alloys. The SF2 alloy showed high wear resistance (WR) than the SF1 alloy in the entire sliding velocities and applied loads. The results indicate that the spray deposited alloys have a lower coefficient of friction (CF(µ)) than the AC alloys under varying load and sliding velocity conditions. The high WR in the SF alloy was due to microstructural modification during SF and precipitation of fine Al2Cu intermetallic and solid solubility effects. The SF2 depicts increased transition from oxidative to abrasive. In other ways, AC alloys demonstrate wear mechanisms that change from oxidative to abrasive and delamination with an increase in sliding velocity and load.

In this work, we investigated the effects of heat treatment on the microstructure, hydrogen storage characteristics and corrosion rate of a Ti₃₄V₄₀Cr₂₄Fe₂ alloy. The arc melted alloy was divided into three samples, two of which were separately quartz-sealed under vacuum and heated to 1000 °C for 1 h; one of these samples was quenched and the other furnace cooled to ambient temperature. The crystal structures of the samples were studied via X-ray diffractometry and scanning electron microscopy. Absorption/desorption characteristics were investigated using a Sievert apparatus. Potentiostat corrosion tests on the alloys were performed using an AutoLab^® corrosion test apparatus and electrochemical cell. All samples exhibited a mixture of body-center-cubic (BCC) and Laves phase structures. The corrosion rate, maximum absorption, and useful capacities increased after both heat treatments. The annealed sample had the highest absorption and reversible capacity. The plateau pressure of the as-cast alloy increased after quenching. The corrosion rate increased from 0.0004 mm/y in as-cast sample to 0.0009 mm/y after annealing and 0.0017 mm/y after quenching, due to a decrease in the Cr-content of the C14 phase.

In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

The fatigue crack growth rate (FCGR) of aluminium alloys under the combined influence of temperature and humidity remains a relatively unexplored area, receiving limited attention due to its intricate nature and challenges in predicting the combined impact of these factors. The challenge was to investigate and address the specific mechanisms and interactions between temperature and humidity, as in coastal environment conditions, on the FCGR of aluminium alloy. The present study conducts a comprehensive investigation on the combined influence of temperature and humidity on the FCGR of Al6082 alloy. The fatigue pre-cracked compact tension specimens were corroded for 7 days and then subjected to various temperature and humidity conditions in a thermal chamber for 3 days to simulate coastal environments. The obtained data were analysed to determine the influence of temperature and humidity on the FCGR of Al6082 alloy. An empirical model was also established to predict fatigue life cycle values under these environmental conditions precisely. The correlation between FCGR and fracture toughness models was also examined. The Al6082 alloy exhibits a 34% increase in the Paris constant C, indicating reduced FCGR resistance due to elevated temperature and humidity levels. At the same time, fatigue, corrosion, moisture-assisted crack propagation, and hydrogen embrittlement lead to a 27% decrease in threshold fracture toughness. The developed model exhibited accurate predictions for fatigue life cycles, and the correlation between fracture toughness and FCGR showed less than 10% error, indicating a strong relationship between these parameters.

Legumes are important sources of nitrogen and, therefore, the nitrogen fixing ability of the legume-rhizobia symbiosis has great potential to improve crop yields or reduce nitrogen fertilizer use. Unfortunately, legumes face serious and increasing threats of both biotic and abiotic stresses among which Fe-deficiency has been increased from past years. Fe nutrient deficiency limits pulse production and nitrogen fixation by specifically affecting any one of the four phases of legume-rhizobium symbiosis. Although Fe in soil is often present in adequate quantities, it is mainly present in insoluble Fe-(III) precipitates, limiting its uptake and utilization. The present review has focused on the iron nutrition and deficiency and probable uptake, transport and metabolism in legumes.

The poor oxidation resistance of refractory high-entropy alloys (RHEAs) is a major obstacle for their use in high-temperature engineering applications. Anti-oxidation coating technology is an effective method for improving the oxidation resistance. In this paper, the Si-20Cr-20Fe coating was prepared on MoNbTaTiW RHEA by a fused slurry method. The microstructural evolution and compositions of the silicide coating under high-temperature oxidation environment were studied. The results show that the silicide coating could effectively prevent the oxidation of the MoNbTaTiW RHEA. The initial silicide coating had a double-layer structure; a high silicon-content layer mainly composed of MSi2 as the outer layer and a low silicon-content layer mainly contained M5Si3 as the inner layer. Under high-temperature oxidation conditions, the silicon element diffused from the silicide coating to the RHEA substrate while the oxidation of the coating occurred. After oxidation, the coating was composed of an outer oxide layer and an inner silicide layer. The silicide layer moved toward the inside of the substrate, led to the increase of its thickness. Compared with the initial silicified layer, its structure did not change significantly. The structure and compositions of the oxide layer on the outer surface strongly depended on the oxidation temperature. This paper provides a strategy for protecting RHEAs from oxidation at high-temperature environments.

A phenomenological constitutive model is developed to describe the uniaxial transformation ratcheting behaviors of super–elastic shape memory alloy (SMA) by employing a cosine–type phase transformation equation with the initial martensite evolution coefficient that can capture the feature of the predictive residual martensite accumulation evolution and the nonlinear hysteresis loop on a finite element (FE) analysis framework. The effect of the applied loading level on transformation ratcheting are considered in the proposed model. The evolutions of transformation ratcheting and transformation stresses are constructed as the function of the accumulated residual martensite volume fraction. The FE implementation of the proposed model is carried out for the numerical analysis of transformation ratcheting of the SMA bar element. The integration algorithm and the expression of consistent tangent modulus are deduced in a new form for the forward and reverse transformation. The numerical results are compared with those of existing model and the experimental results to show the validity of the proposed model and its FE implementation in transformation ratcheting. Finally, a FE modeling is established for a repeated preload analysis of SMA bolted joint

A series of Si-bearing MgAl₂O₄-spinels were synthesized at 1500-1650 °C and 3–6 GPa. These spinels had SiO₂ contents up to ~1.03 wt%, and showed a substitution mechanism of Si⁴⁺ + Mg²⁺ = 2Al³⁺. Unpolarized Raman spectra were collected from polished single grains, and displayed a set of well-defined Raman peaks at ~610, 823, 856 and 968 cm^-1 which had not been observed before. Aided with the Raman features of natural Si-free MgAl₂O₄-spinel, synthetic Si-free MgAl₂O₄-spinel, natural low quartz, synthetic coesite, synthetic stishovite and synthetic forsterite, we infer that these Raman peaks should belong to the SiO₄ groups. The relations between the Raman intensities and SiO₂ contents of the Si-bearing MgAl₂O₄-spinels suggest that at some P-T conditions some Si must adopt the M-site. Unlike the SiO₄ groups with very intense Raman signals, the SiO₆ groups are largely Raman-inactive. We have further found that the Si cations primarily appear on the T-site at P-T conditions ≤ ~3–4 GPa and 1500 °C, but attain a random distribution between the T-site and M-site at P-T conditions ≥ ~5–6 GPa and 1630–1650 °C. This Si-disordering process observed for the Si-bearing MgAl₂O₄-spinels hints that similar Si-disordering might happen to the (Mg,Fe)₂SiO₄-spinels (ringwoodite), the major phase in the lower part of the mantle transition zone of the Earth and the index mineral for the very strong shock stage experienced by extraterrestrial materials. The likely consequences have been explored.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ~ 400 nm nano-holes in a Cr etch mask that was tens-of-nm thick. Nano-holes ablated at slightly above the threshold of ablation irradiance became nano-disks and nano-rings at slightly lower pulse energies. Subtle sub-1 nJ pulse energy control was harnessed to pattern large surface areas with controlled nano-alloying of Si and Cr. This technique is extendable to vacuum-free large area patterning of nanolayers by alloying them at distinct locations with sub-diffraction resolution. Such metal masks with nano-hole opening can be used for formation of random patterns of nano-needles with sub-100 nm separation when applied to dry etching of Si.

SLM Additive Manufacturing has demonstrated great potential for aerospace applications when structural elements of individual design and/or complex shape need to be promptly supplied. 3D-printable AlSi10Mg (RS-300) alloy is widely used for the fabrication of different structures in aerospace industry. The importance of the evaluation of residual stresses that arise as a result of complex 3D-printing process thermal history is widely discussed in literature, but systematic assessment remains lacking for their magnitude, spatial distribution, and comparative analysis of different evaluation techniques. In this study we report the results of a systematic study of residual stresses in a 3D-printed double tower shaped samples using several approaches: the contour method, blind hole drilling laser speckle interferometry, X-ray diffraction, and Xe pFIB-DIC micro-ring-core milling analysis. We show that a high level of tensile and compressive residual stresses is inherited from SLM 3D-printing and retained for longer than 6 months. The stresses vary over a significant proportion of the material yield stress. All residual stress evaluation techniques considered returned comparable values of residual stresses even regardless of dramatically different dimensional scales from millimeters for the Contour Method down, laser speckle interferometry and XRD and down to small fractions of a mm (70 μm) for Xe pFIB-DIC ring-core drilling. The use of residual stress evaluation is discussed in the context of optimizing the printing strategy to enhance the mechanical performance and long-term durability.

With an increase in energy consumption globally, Fischer-Tropsch (FT) synthesis is a good alternative for producing fuels and chemicals from coal, natural gas or biomass. Among them, coal to liquids has been put into production in countries that have large coal reserves. In this process, Fe-based catalysts are commonly used due to their earth abundance, comparatively wide operation range and ready availability to handle low H2/CO ratio from coal. Despite their extensive applications, the kinetic and mechanistic understandings of Fe carburization and FT reaction on Fe-carbides are relatively limited due to the complexity of phase composition of the applied catalysts. This review summarizes the current state of knowledge of FT synthesis on Fe-carbide with an emphasis on underlying mechanism. Specifically, the employment of model catalyst, such as Raney-Fe, could provide a convenient way to furnish kinetic information regarding Fe carburization and subsequent FT reaction. A major challenge for further understanding catalytic reactions occurring at the Fe-carbide surface is correlating FT activity and selectivity to specific active site. To address this issue, the advancements of both DFT calculations and surface science techniques are highly demanded.

Metal-Organic Frameworks (MOFs) have been observed to exclusively eliminate dyes confined within their respective pores. In this investigation, the synthesis of a breathable MOF structure, MIL-88B(Fe), was pursued with the objective of circumventing restrictions on pore size to en-hance its adsorption capabilities. The synthesis of MIL-88B(Fe) was carried out via the assisted solvothermal method at 373 K using inexpensive yet environmentally benign FeCl3.6H2O, 1,4-benzenedicarboxylic acid and DMF as metal precursor, as linker and solvent, respectively. Furthermore, MOF was subjected to extensive analytical characterization using XRD, FT-IR spectroscopy, N2 gas sorption, TGA, and SEM. The experimental data showed that the utilization of MIL-88B(Fe) with a dose level of 5 mg for 180 mins at pH of 9 led to the highest levels of ad-sorption for both dyes with 162.82 mg g-1 for Methylene Blue (MB) and 144.65 mg g-1 for Rho-damine B (RhB), as a result of contrast molecular size between each dye. The Langmuir and Freundlich models demonstrate a correlation with isotherms, while the thermodynamic analysis demonstrated that MIL-88B(Fe) exhibits distinct endothermic and breathable properties. The ef-ficacy of MIL-88B(Fe) adsorbent for MB and RhB in aqueous solutions indicated exceptional performance, stability, and noteworthy reusability performance.

Due to increased energy intensive human activities resulting accelerated demand for electric power coupled with occurrence of natural disasters with increased frequency, intensity, and duration, it becomes essential to explore and advance renewable energy technology for sustainability of the society. Addressing the stated problem and providing a radical solution has been attempted in this study. To harvest the renewable energy, among variety of solar cells reported, a composite a-Si/CZTS photovoltaic devices has not yet been investigated. The calculated parameters for solar cell based on the new array of layers consisting of a-Si/CZTS are reported in this study. The variation of i) solar cell efficiency as a function of CZTS layer thickness, temperature, acceptor, and donor defect concentration; ii) variation of the open circuit current density as a function of temperature, open circuit voltage; iii) variation of open circuit voltage as a function of the thickness of the CZTS layer has been determined. There has been no reported study on a-Si/CZTS configuration-based solar cell, analysis of the parameters, and study to address the challenges imped efficiency of the photovoltaic device and the same has been discussed in this work. The value of the SnO2/a-Si/CZTS solar cells obtained from the simulation is 23.9 %.

The fabrication and characterisation of photo-anodes based on black-Si (b-Si) are presented using a photo-electrochemical cell in NaOH solution. Black-Si was fabricated by maskless dry plasma etching and was conformally coated by tens-of-nm of TiO2 using atomic layer deposition (ALD) with a top layer of CoO_x cocatalyst deposited by pulsed laser deposition (PLD). Low reflectivity R < % of Black-Si over the entire visible and near-IR (λ < 2 µm) spectral range is favourable in better absorption of light while an increased surface area facilities larger current densities. Photoelectrochemical performance of the heterostructured photoanode is discussed in terms of n-n junction between b-Si and TiO₂.

Polymer-derived ceramic (PDC) based coatings like Si-C-N and their derivatives are gaining importance day by day in N/MEMS and aerospace due to their thermos-mechanical stability and conductivity. The crystallized, amorphous, and near amorphous morphology of SiCN nanocomposite coatings based on deposition conditions requires thorough investigation for appropriate utilization as they lead to differences in mechanical properties (quantified using nanoindentation in this case). A 4-stage model was proposed based on Raman spectroscopy due to the N₂-Ar pressure variations during the deposition process of SiCN coatings by magnetron sputtering. The integral intensity of the G (graphitic), disorder (D), and tetrahedral (T) peaks namely I_G, I_D, and I_T were calculated after the deconvolution of the spectra. The sp² domain size and defect parameters were evaluated and correlated with the hardness and different bond formation involving Si, C, and N. Image analysis revealed the atomic migration involved during the growth process leading to crystallization along with the formation of voids and defects. The observations were supported by FTIR and TEM-SAED analysis. The outcomes provide a foundation causing an urge to develop similar models with further elemental additions and correlate with various physical properties.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

We investigate the ammonium removal abilities of natural and synthetic zeolites, which have distinct Si/Al ratios and various surface areas, to study how adsorption and ion-exchange processes in zeolites perform under different ammonium concentrations and different temperatures. Five zeolites including natural mordenite, chabazite, erionite, clinoptilolite and synthetic merlinoite were immersed in 20 mg/kg, 50 mg/kg and 100 mg/kg ammonium solutions. The results demonstrate that zeolites under high ammonium concentrations (100 mg/kg) possess higher physical adsorption capacity (0.398–0.468 meq/g), whereas those under lower ammonium concentrations (20 mg/kg) possess greater ion-exchange property (64–99%). The ion-exchange ability of zeolites are extremely dependent on the cation content of the zeolites, and the cation content is affected by the Si/Al ratio. The surface area of zeolites also has a partial influence on its physical adsorption ability. When the surface area is less than 100 m²/g, the adsorption ability of zeolite increases obviously with surface area; however, adsorption ability is saturated as the surface area becomes larger than this critical value of 100 m²/g. When we carried out the zeolites in 50 mg/kg ammonium concentration at different temperatures (5~50 ℃), we found that zeolites exhibit the highest ammonium removal ability at 30°C and the potassium release was enhanced at 30~40 ℃.

As one of toxic Volatile Organic Pollutant (TVOCs), formaldehyde has a toxic effect on microorganisms, and then inhibits the biochemical process of formaldehyde wastewater treatment. Therefore, the selective degradation of formaldehyde is of great significance to achieve formaldehyde wastewater high-efficiency and low-cost treatment. This study constructed a heterogeneous Fe-ZSM-5/H2O2 Fenton system for selective degradation to target compounds. By bonding Fe3+ onto the surface of ZSM-5 molecular sieve, Fe-ZSM-5 was prepared successfully. XRD, BET and FT-IR spectral studies shown the prepared Fe-ZSM-5 was mainly composed of micropores. The influences of different variables on formaldehyde selective heterogeneous Fenton degradation performance were studied. The 93.72% formaldehyde degradation and the 98.15% selectivity of formaldehyde compared with glucose had demonstrated in the optimized Fenton system after 360 min. Notably, the resultant selective Fenton oxidation system had a wide range of pH suitability from 3.0 to 10.0. Also, the Fe-ZSM-5 was used in 5 consecutive cycles, while the degradation efficiency of formaldehyde did not drop dramatically. Using reactive oxygen species scavengers, hydroxyl radical was the main active substance to degrade formaldehyde. Furthermore, the great degradation performance of this system to high concentration of formaldehyde was acquired, and the degrading efficiency was more than 95%.

Iron (Fe) deficiency specifically is the most common nutritional disorder due to insufficient absorbable Fe. Biofortification is a process of enriching the nutrient content of staple crops and is considered as a sustainable and cost-effective strategy to address micronutrient deficiency problems especially in the less developed countries. Chickpea (Cicer arietinum L.) is a staple food in many developing countries worldwide and is an excellent source of micronutrients. Biofortification of chickpea is a possible solution to address Fe deficiency problem. Chickpea biofortification experiment was conducted under field conditions to evaluate the effects of different doses of Fe fertilizer (0 kg ha-1,10 kg ha-1 and 30 kg ha-1 of Fe-EDDHA) on Fe content in seeds of 18 chickpea cultivars. The experiment was designed as a factorial combination of 18 chickpea cultivars and 3 different doses in a randomized complete block design with 4 replications at two locations in Saskatchewan in 2015 and 2016. Fe concentration in seeds across 18 different chickpea cultivars increased with Fe fertilization. Fe concentration in X05TH20-2 and CDC Frontier cultivars increased from 57 ppm to 59 ppm and 56 ppm to 58 ppm, respectively, after adding Fe fertilizer in both location in 2015 and 2016.

Iron is an essential micronutrient for Citrus, playing an important role in photosynthesis and yield. The aim of this paper is to evaluate the tolerance to Fe deficiency of five Citrus rootstocks: sour orange (S), Carrizo citrange (C), Citrus macrophylla (M), Troyer citrange (T) and Volkamer lemon (V). Plants were grown for 5 weeks in nutrient solution that contained the following Fe concentrations (in µM): 0, 5, 10, 15 and 20. At the end of the experiment, biomass (dry weight), leaf area, total leaf chlorophyll (CHL) and the activity of root chelate activity (FCR) were registered. Additionally, the mineral composition of roots (R) and shoots (S) was evaluated. Principal Component Analysis was used to study the relationships between all parameters and, subsequently, the relations between rootstocks. In the first component, N-S, P-S, Ca-S, Cu-S, Zn-S, Mn-S and Zn-R and Mn-R concentrations were related to leaf CHL and FCR. Increases in leaf CHL, Mg-R, DW (shoots and roots) were inversely related to Cu-R, which was shown in the second component. The values obtained were consistent for V10, C15, and C20, but in contrast for S0 and S5. Overall, the Fe/Cu ratio was significantly related to CHL, which may be used to assist rootstock performance.

In this work the influence of the structure forming agent on the composition, morphology and oxygen reduction reaction (ORR) activity of Fe-N-C catalysts was investigated. As structure forming agent (SFA), dicyandiamide (DCDA) (nitrogen source) or oxalic acid (oxygen source) or mixtures thereof were used. For characterization, cyclic voltammetry and rotating disc electrode (RDE) experiments were performed in 0.1 M H2SO4. In addition to this, N2 sorption measurements and Raman spectroscopy were performed for the structural characterization. The role of metal, nitrogen and carbon sources within the synthesis of Fe-N-C catalysts has been pointed out before. Here, we show that the optimum in terms of ORR activity is achieved if both N- and O-containing SFAs are used in almost similar fractions. All catalysts display a redox couple, whereat its position depends on the fractions of SFAs. The SFA has also a strong impact on the morphology: Catalysts that were prepared with a larger fraction of N-containing SFA revealed a higher order in graphitization, indicated by bands in the 2nd order range of the Raman spectra. Nevertheless, the optimum in terms of ORR activity is obtained for the catalyst with highest D/G band ratio. Therefore, the results indicate that the presence of an additional oxygen-containing SFA is beneficial within the preparation.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

Our results demonstrated that SWT stimulates osteoblastogenesis and increase the cell number of osteoblasts, suggesting positive regulatory effects on osteoblast differentiation. However, the effect of SWT on bone formation need further examination, since the expression of alp gene is downregulated. On the other hand, SWT appears to negatively regulate osteoclast differentiation and bone resorption, as number of osteoclasts and the expression of critical bone resorptive genes are all downregulated. Collectively, SWT might change the equilibrium of bone remodeling and increase the bone mass. Our data provided supportive evidences that this medicine formulation can be applied to treat osteoporosis or bone destructive diseases.

The present study conducts the phase analysis, microstructural characteristics, and mechanical property evaluation on the as-cast and quenched Ti-15Mo-xFe alloys with high iron content ranging from 4 to 12 weight percent. All the four alloys were produced in a button-arc melting furnace. Heat treatment in the form of solution treatment was performed in a muffle furnace at a temperature of 1100°C, with a 1-hour holding time. The samples were rapidly quenched in ice-brine. Various characterization techniques were used to analyze samples both in the as cast and quenched conditions. X-ray diffractometer (XRD) was used to analyses the phases present in each alloy whereas the optical microscope (OM) was employed to track the microstructural evolution. The mechanical properties of the alloys were evaluated using a tensile test method while the micro-Vickers hardness measurements were conducted to evaluate hardness of the alloys. OM micrographs revealed equiaxed β grains and substructures in as-cast TMF0, dendritic structure, and equiaxed β grains with pores forming around the grain boundaries in TMF1, and micrograph full of dendrites and pores was observed in the as-cast TMF2 and TMF3 alloys. The quenched TMF0 showed only β equiaxed grains whereas TMF1, TMF2, and TMF3 revealed micrographs full of equiaxed grains of β phase with pores throughout the grain boundaries. The XRD patterns of cast TMF0 showed peaks belonging to the β and orthorhombic α″ martensitic phases and the quenched sample showed the bcc β phase only. The TMF1, TMF2, and TMF3 alloys in as-cast condition indicated peaks belonging to β , α″ and intermetallic B2 TiFe phases, however, their quenched samples showed the presence of β and Fe·Ti·O2 phases in TMF2 and TMF3 alloys. The tensile properties such as ultimate tensile strength (UTS) and elastic modulus (E) of as-cast TMF0 were 264 MPa and 79 GPa and these properties changed upon quenching to 411 MPa and 66 GPa respectively. The elastic modulus of TMF1 in as-cast condition was 74 GPa. The UTS and E of TMF1, TMF2, and TMF3 in as cast and quenched conditions were not recorded due to the fragility of the samples that failed prior to yielding any useful data. The micro-Vickers hardness in as cast and quenched conditions showed a similar trend with hardness increasing slightly upon quenching for TMF0, TMF1, and TMF3 alloys but slightly decreased in the case of TMF2. 6). The fracture surfaces of TMF0 exhibited both ductile and brittle fracture in as cast and quenched conditions whereas the only brittle fracture mode was observed in the TMF1, TMF2 and TMF3 alloys in both conditions.

Hollow and concrete-filled steel tubes (CFSTs) are widely used as columns in many structural systems and local buckling can occur when they are subjected to axial compression loading. The critical regions for the local buckling of the columns are near the ends of the column where the moments are the highest. To strengthen the critical regions of the CFSTs the CFRP provides a simple and effective method which used previously as an enhancement for both of strength and ductility. So, this study suggests investigating the axial load behaviour of CFST strengthened with CFRP using FE method after a verification study and then a various parametric studies were carried out to cover the effect of the CFRP layers, number, confinement length and position. The FE results proved that, one CFRP sheet with thickness equal to 1.2 mm was strengthened the composite column by 8.5%, two CFRP sheets with total thickness equal to 2.4 mm was strengthened the composite column by 23.5%, three CFRP sheets with total thickness equal to 3.6 mm was strengthened the composite column by 35.1% and four CFRP sheets with total thickness equal to 4.8 mm was strengthened the composite column by 44.5%. Moreover, this study proved that by strengthened the composite columns with CFRP sheets with different lengths, the axial load resistance was improved by 8.5%, 4.6%, 0.1% and 0.0% for length percentages 100%, 75%, 50% and 25% respectively.

Understanding of the correlation between the magnetomechancial coupling factors (k) and damping factors (Q^-1) is a key pathway to enhance the magnetomechanical power conversion ef-ficiency in laminated magnetoelectric (ME) composites by engineeringly manipulating the magnetic and mechanical properties of Fe-based amorphous metals. The k and Q^-1 factors of FeSiB amorphous ribbons annealed in air at different temperatures are investigated. It is found that k and Q^-1 factors are affected by both magnetic and elastic properties. The magnetic and elastic properties are equalized in terms of the magnetomechanical power efficiency for the low temperature annealing. The k and Q^-1 of FeSiB-based epoxied laminates with different stacking numbers show that the -3 dB bandwidth and Young’s modulus are equalized in terms of the magnetomechanical power efficiency for the high lamination stacking.

This paper aims to investigate the feasibility of strengthening the web opening in the shear zone of RC beams by using iron-based shape memory alloy (Fe-SMA) bars. To conduct this study, numerical analysis with ABAQUS software was employed. The research was divided into six groups of beams with web openings of different lengths (150, 300, and 450 mm), prestressing levels (0%, 30% and 60%), and reinforcement diameters (14, 18, and 22 mm) of Fe-SMA bars. The results show that the presence of web openings can cause a significant reduction in the cracking and ultimate loads of the beams, with reductions ranging from 11 to 50% and 36 to 48%, respectively. However, by adding pre-stressed Fe-SMA bars around small web openings (100×150 mm), the shear capacity of the beam is restored, and the beam exhibits behavior similar to solid beams. Additionally, activating the Fe-SMA bars by 30 and 60% resulted in almost similar cracking loads but improved load-carrying capacity of the beam with small openings by 12% and 9%, respectively, compared to the solid beam. The technique proposed for enhancing shear strength is most effective for beams with small (100×150 mm) and medium (100×300 mm) web openings as it can restore both the beam’s shear strength and stiffness. However, for beams with larger web openings (100×450 mm), the use of activated Fe-SMA beams can recover almost 90% of the solid beam's shear capacity. Furthermore, reinforcing small openings with Fe-SMA bars of different diameters enhances beam shear capacity and stiffness, while for larger openings, higher Fe-SMA reinforcement ratios could potentially restore the beam's full strength and stiffness. This study emphasizes the importance of strengthening web openings in RC beams, particularly in shear zones, and provides significant insights into how to strengthen beams with web openings, thereby contributing to developing safer structures. However, further laboratory experiments are recommended to validate, complement and extend the findings of this numerical study.

Fe rich soft magnetic alloys are candidates for applications as magnetic sensors and actuators. These alloys can also be added to hard magnetic compounds to obtain spring magnets. In this work we produce two nanocrystalline Fe-Zr-B-Cu alloys by the powder metallurgy powder technology of mechanical alloying. The increase of the boron content favors the reduction of the crystalline size. Thermal analysis (by differential scanning calorimetry) shows at temperatures between 450 and 650 K wide exothermic processes, associated with the relaxation of tensions of the alloys produced by milling. At high temperatures, a main crystallization peak is found. The apparent activation of this process was determined by Kissinger and isoconversional methods. The values are compared with those found in the scientific literature. Likewise, adapted thermogravimetry permits to determine the Curie temperature. The functional response has been analyzed by hysteresis loop cycles. According to the composition, the decrease of the Fe/B ratio diminishes the magnetic soft behavior.

We extend our high-resolution MRI-based Finite Element (FE) head model, previously presented and validated in [1–3], by considering the heterogeneities of the white matter structures captured through the use of Magnetic Resonance Elastography (MRE). This approach imparts more sophistication to our numerical model and yields results that more closely match experimental results. It is found that the peak pressure more closely matches the experiments as compared to the heterogeneous case. Qualitatively, we find differences in stress wave propagation near the corpus callosum and the corona radiata, which are stiffer on average than the global white matter. We are able to study the effects of these stiff structures on transient stress wave propagation within the cerebrum, something that cannot be done with a homogenized material model.

The X-ray induced spin crossover transition of an Fe(II) molecular thin film in the presence and absence of a magnetic field has been investigated. The thermal activation energy barrier in the soft X-ray activation of the spin crossover transition for [Fe{H2B(pz)2}2(bipy)] molecular thin films is reduced in the presence of an applied magnetic field, as measured through X-ray absorption spectroscopy at various temperatures. The influence of a 1.8 T magnetic field is sufficient to cause deviations from the expected exponential spin state transition behavior that is measured in the field free case. We find that orbital moment diminishes with increasing temperature, relative to the spin moment in the vicinity of room temperature.

Currently, conventional spark-ignition engines face challenges in meeting the ever-growing demands of customers and increasingly stringent regulations regarding pollutant emissions. A combination of innovative strategies and carbon-neutral fuels is deemed necessary in order to further reduce fuel consumption and minimize engine emissions. The present work aims to assess the performance of combustion strategies using low-carbon content fuel, such as methanol M100, ignited by a plasma-assisted igniter (PAI) under ultra-lean conditions. The experimental campaign is conducted on a single-cylinder research engine at different engine speeds and low loads, moving up to the engine lean stable limits. To determine the benefits brought by the proposed strategy, referred to as M100-PAI, the obtained outcomes are compared with the ones obtained using market gasoline E5 ignited by the PAI system and conventional spark. The synergy between M100 (methanol) and Plasma Assisted Ignition (PAI) in internal combustion engines yielded notable benefits. This combination significantly improved combustion stability if compared to the other combinations tested, by extending the lean stable limit to λ=2.0, reducing cycle-to-cycle variability, and facilitating faster flame front acceleration, resulting in enhanced homogeneity. These enhancements, obtained with the combination M100-PAI, contributed to higher fuel efficiency showing a 10% efficiency gain over the combination E5-gasoline spark ignition.

Hydrogen fuel is gaining particular attention in internal combustion engines. In addition to zero-carbon emissions, major advantages relate to its combustion characteristics, which allow significant increase in thermal efficiency under ultra-lean operation and with very low NOx levels. The ignition system is one of the main technology enablers, as it determines the capability to control ultra-lean operations, avoid backfire phenomena, or reduce the risks of abnormal combustions. The latter results from the hydrogen low ignition energy and it is associated with factors like high-temperature residuals, hot spots, and irregular spark plug discharge. ACIS gen 2-Barrier Discharge Igniter excels in accelerating the initial flame growth speed by the generation of non-equilibrium low-temperature plasma, strong ignition promoter for the combined action of kinetic and thermal effects. Moreover, its volumetric discharge facilitates combustion initiation on a wide region, in contrast to the localized ignition of traditional spark systems. In this work we present for the first time, to the best of our knowledge, experimental results showing the performance of a hydrogen engine with a low-temperature plasma discharge. Tests were conducted on a single-cylinder research engine, achieving ultra-lean conditions with cycle-to-cycle variability results below 2.5%. The analysis indicates that the H2 - BDI combined solution is capable of accelerating the evolution of the flame front compared to traditional spark plugs, leading to a significant reduction in the cycle-to-cycle variability. A meticulous adjustment of the BDI control parameters further enhances igniter performance and contributes to a deeper understanding of the innovative approach proposed in this study.

Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ~ 0.4 − 1 μm holes in alumina Al2O3 etch masks with 20-50 nm thickness. Such dielectric masks simplify fabrication of photonic crystal (PhC) light trapping patterns for the above-Lambertian performance of high efficiency solar cells. Conditions of laser ablation of transparent etch masks and effects sub-surface Si modifications were revealed by plasma etch- ing, numerical modeling, and minority carrier lifetime measurements. Mask-less patterning of Si is proposed using fs-laser direct writing for dry plasma etch of Si.

The synergistic effect of silicon and cerium addition on the oxidation resistance of pack cementation aluminide coating applied on Ni-based superalloy substrate was investigated. The effect of cerium and silicon on the scale morphology, oxidation behavior, and scale spallation tendency are discussed based on the experimental results, using X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analyses (EDX). In addition, the oxidation resistance was evaluated by measuring the weight of samples after each 16-hour cycle at 1100˚C for 50 cycles. The experiments indicated that silicon addition to aluminide coating improves the oxidation resistance through the formation of β-NiAl1-nSin and δ-Ni2Al3-nSin and δ-Ni2Si phases. Furthermore, the addition of 1% cerium to modified aluminide enhances the formation of the fine-grained microstructure of the β-NiAl and δ-Ni2Al3 and reduces the outward/inward diffusion of elements (so-called blocking effect) which significantly modifies the hot oxidation resistance. The addition of 2% cerium, owing to the distortion of the β-NiAl and δ-Ni2Al3 phases, strictly decreases the hot oxidation resistance and the coating is exfoliated after 450 h at 1100 °C. The cyclic oxidation tests showed that the samples containing 1% cerium and 6% silicon possess the highest hot oxidation resistance in which 2 mg/cm2 weight loss of Ce-Si-aluminide was reported after 800 h. This is attributed to the simultaneous effect of cerium and silicon during the deposition process which reduces the oxygen diffusion and reduces the growth rate of α-Al2O3 during oxidation tests. The α-Al2O3 oxidation layer morphology showed that finer grains are formed in samples containing optimum ratios of cerium and silicon which indicates that these elements improve the coating adhesion and oxidation resistance simultaneously.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

In the present study, the corrosion resistance of amorphous coating and composite coatings in 3.5 wt.% NaCl, 0.5 M H₂SO₄ and 10 wt.% NaOH solution were studied. The composite coatings exhibit superior corrosion resistance. When the content of AT13 （Al₂O₃–13 wt.% TiO₂）was 15 wt.%, the composite coating has the lowest corrosion current density (1.75×10^-6 A cm^-2), which is 5.14×10^-5 A cm^-2 for Fe-based metallic glassy coating, and the highest corrosion potential (-411 mV), which is -580 mV for Fe-based metallic glassy coating. The breakdown potential of the passivation film in 3.5 wt.% NaCl solution was much higher than that of 316L.The long-time immersion corrosion tests carried out on different coatings showed that the corrosion protection effect of coating was enhanced with the increase of the amount of AT13 added.

Tissues of the brain, especially white matter, are extremely heterogeneous - with constitutive response varying spatially. In this paper, we implement a high-resolution Finite Element (FE) head model where heterogeneities of white matter structures are introduced through Magnetic Resonance Elastography (MRE) experiments. Displacement of white matter under shear wave excitation is captured and the material properties determined though an inversion algorithm are directly used in the FE model. This approach is found to improve model predictions when compared to experimental results. In the first place, responses in the cerebrum near stiff structures such as the corpus callosum and corona radiata are markedly different compared with a homogenized material model. Additionally, the heterogeneities introduce additional attenuation of the shear wave due to wave scattering within the cerebrum.

Conventional models do not fully explain composition of the solar system – for example, the presence of p-nuclei and post-post-Fe-nuclei remains not yet understood (and is one of the great unresolved puzzles of nuclear astrophysics in general); other puzzles exist. We offer a hypothesis which can explain the appearance of non-native elements in the solar system, and a feasible scenario for its implementation. The hypothesis suggests that a nuclear-fission "event" occurred in the inner part of the solar system at the time currently defined as the birth of the system. Conventional models have never considered fission as a contributing nuclei-production mechanism. Upon examination of the existing models and factual data (presented in volumes of publications but never combined into an aggregate), we identified one plausible scenario by which a fission event (not demolishing the entire solar system) could occur: an encounter with a compact super-dense stellar "fragment" (with specific properties) and its "explosion" in fission-cascades. Such scenario also helps resolve other long-standing puzzles of the solar system. For example, it provides that the fission-produced nuclei subsequently transformed into the material that (eventually) accreted into the "rocky" objects in the system (terrestrial planets, asteroids, etc.) and enriched the pre-existed hydrogen-helium objects (the Sun and the gaseous giants) – this offers an explanation for the planets’ inner position and compositional differences within the predominantly hydrogen-helium rest of the solar system. Other implications also follow.

A new and easy-to-make polymer film sensor was prepared by dip-coating technique and this film used as fluorescent chemosensor for the detection of metal ions in aqueous solution. The proposed film sensor exhibited dual emissions at 540 and 582 nm under a single excitation wavelength. The fluorescence behavior of this film sensor toward metal ions has been investigated using these two wavelengths. The proposed sensor was found to show selectivity and sensitive to Fe³⁺ ion when compared the other metal ions in deionized water with excellent photostability. Detection limit of the polymeric film sensor was calculated as 86.15 and 28.90 μM. The results showed that the sensor can be successfully applied to the determination of Fe³⁺ ions in aqueous media. Contact angle measurement of PAZU film probe was also investigated and the result showed that the proposed film probe has hydrophobic property.

The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.

The cast defects strongly degrade the mechanical properties in cast alloys. The effect of Sn addition on Al-Si alloys was investigated by 3D computed tomography, SEM and TEM. Amorphous Sn oxides are found near the alumina film, cause more shrinkage pores, initiate cracks and deteriorate mechanical properties. This work suggests not adding Sn in various Al alloys used in cast state.

Silicon has a theoretical specific capacity of 4200 mAh g−1, which is considered to have significant potential for anode materials in lithium-ion batteries (LIBs). However, the volume change that occurs in silicon during charging and discharging affects the development of commercial applications. In this work, a yolk-shell structured Si@void@C anode material has been developed to address this problem. The silicon nanoparticle yolk material is obtained by recycling kerf-loss (KL) Si waste from the photovoltaic industry, the carbon shell is prepared via a hydrothermal process with glucose, and the sacrificial interlayer is Al2O3. The synthesized material is used to fabricate anodes that show a high reversible capacity of 836 mAh g−1 at the current density of 0.1 A g−1 after 100 cycles, with a Coulomb efficiency of 71.4%. This work demonstrates a relatively low-cost approach to turn KL Si waste into value-added materials for LIBs.

Traditional refractory materials such as nickel-based superalloys have been gradually unable to meet the performance requirements of advanced materials. The Mo-Si-based alloy, as a new type of high temperature structural material, has entered the vision of researchers due to its charming high temperature performance characteristics. However, its easy oxidation and even "pesting oxidation" at medium temperatures limit its further applications. In order to solve this problem, researchers have conducted large numbers of experiments and made breakthrough achievements. Based on these research results, the effects of rare earth elements like La, Hf, Ce and Y on the microstructure and oxidation behavior of Mo-Si-based alloys were systematically reviewed in the current work. Meanwhile, this paper also provided an analysis about the strengthening mechanism of rare earth elements on the oxidation behavior for Mo-Si-based alloys after discussing the oxidation process. Furthermore, the research focus about the oxidation protection of Mo-Si-based alloys in the future was prospected to expand the application field.

Bulk composition, mineralogy and microchemistry of various fractions of the filling of the Crater No. 4 at Emmerting were investigated. Here we present mainly the fine fractions, which, in contrast to pebbles larger than ca. 4 cm, are relatively poor in material affected by melting. A 0.1 mm long meteorite fragment without ablation features was found, and remelted fragments of the same body have been identified. The projectile was dominated by enstatite, also containing forsterite, basic plagioclase, Ni-rich pyrrhotite and troilite, kamacite, silica, and probably merrillite. The molten fragments contain porous Mg-rich glass (indicating temperature &gt; 1500 °C), minor Fe oxides, and occasionally uncommon Ni-rich minerals. The bulk composition and electron microprobe show that the amount of meteoritic material is low (&lt;&lt; 1 %), and it is not unequivocally manifested even in platinum-group elements abundances and osmium isotope ratios (the latter, however, were only measured in two samples). This can be explained by dilution of the filling by particles brought after the crater formation, and by probably achondritic composition of the projectile. Relatively large hollow spheroid Fe oxide particles were observed in thin sections from the magnetic fraction. A Mn oxide hollow spherule has also been found. In magnetically separated filling from the nearby Crater No. 5, bulk chemical composition points to contamination with several metals and metalloids probably due to influence of recent alluvial sediments. Therefore, the extent of meteoritic contamination in this crater may be even smaller.

Soil cadmium (Cd) contamination has become a serious problem in China. In this study, the goals of the field experiments were to understand how the application of nitrogen fertilizer at the full heading stage and filling stage reduced the uptake of Cd in rice by affecting the distribution of Cd in iron plaques on the root surfaces and subcellular in the root and flag leaf. The hydroponic culture experiments aimed to explore the effect of interaction or deficiency of nitrogen and cadmium on cadmium accumulation in rice at the late growth stage. The results showed that under the condition of having enough nitrogen supply during the early growth stage, applying nitrogen fertilizer during the full heading stage and filling stage resulted in a significant increase in the concentration of Fe and Cd on the root plaques at the milk stage and mature stage. Additionally, it increased the concentration and proportion of Cd in the soluble fraction of subcellular in the flag leaves at the milk stage. On the other hand, when there was a deficiency of nitrogen, the concentration of Fe in the root plaques increased significantly, while the concentration of Cd in the root plaques decreased significantly. Moreover, the proportion of Cd in the flag leaf cell walls increased significantly. Regardless of whether there was sufficient or deficient nitrogen supply during the early growth stage, applying nitrogen at the full heading stage reduced the Cd concentration in brown rice by 35.11% and 57.25%, respectively. Under hydroponic culture conditions with both Cd exposure and later-stage nitrogen supply significantly increased the Cd concentration in brown rice. However, in the absence of Cd, nitrogen supply significantly reduced the Cd concentration in brown rice. The accumulation of Cd in brown rice was significantly correlated with the accumulation of Fe and Mn at the late growth stage. Our findings indicate that when there is sufficient nitrogen nutrition during the early growth stage of rice, topdressing nitrogen fertilizer at the full heading stage combined with lime with mineral element fertilizers such as Fe and Mn is an effective approach to reduce the presence of cadmium in rice grains.

It was recently demonstrated that a co-planar capacitive sensor could be applied to the evaluation of materials without the disadvantages associated with the other techniques. This technique effectively detects changes in the dielectric properties of the materials due to, for instance, imperfections or variations in the internal structure, by moving a set of simple electrodes on the surface of the specimen. An AC voltage is applied to one or more electrodes and signals are detected by others. This is a promising inspection method for imaging the interior structure of the numerous materials, without the necessity to be in contact with the surface of the sample. In this paper, Finite Element (FE) modelling was employed to simulate the electric field distribution from a co-planar capacitive sensor and the way it interacts with a non-conducting sample. Physical experiments with a prototype capacitive sensor were also performed on a Plexiglas sample with sub-surface defects, to assess the imaging performance of the sensor. A good qualitative agreement was observed between the numerical simulation and experimental result.

Iron (Fe) and zinc (Zn) deficiency in cereal grains has deleterious effects on the health of millions of people, especially in developing countries. As wheat, as a staple crop, is consumed in large quantities, its micronutrient content is important. Crops in Africa are often grown under low nitrogen (N) and low phosphorous (P) conditions. The aim of this study was to determine the effect of low N and low P stress on Fe and Zn and phytic acid concentration, in two commercial spring wheat cultivars with excellent baking quality. The two cultivars did not differ significantly for the measured characteristics. Across all treatments the average values for Fe varied between 19.60-28.61 mg kg^-1, Zn between 17.68-33.79 mg kg^-1 and phytic acid between 5.03-6.92 mg g^-1. Low P stress lead to the highest values of Fe and Zn, and the lowest value for phytic acid. Phytic acid:Fe and phytic acid:Zn ratios were also highly significantly reduced under low P stress conditions. Low N conditions caused significantly increased Zn levels. Despite this, the phytic acid:Fe and phytic acid:Zn ratios were relatively high under all conditions, indicating a low bioavailability of both Fe and Zn in these wheat cultivars.

The outdoor field test of the 4-terminal on Si tandem photovoltaic module (specifically, InGaP/GaAs on Si) was investigated and performance model, considering spectrum change affected by fluctuation of atmospheric parameters, was developed and validated. The 4-terminal on Si tandem photovoltaic module had about 40 % advantage in seasonal performance loss compared with standard InGaP/GaAs/InGaAs 2-terminal tandem photovoltaic module. This advantage is expanded in (subarctic zone) < (temperate zone) < (subtropical zone). The developed and validated model used all-climate spectrum model and considered fluctuation of atmospheric parameters, and can be applied every type of on-Si tandem solar cells.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

Microbial-mediated biogeochemical cycling of iron is widespread in anaerobic environments such as sediments and deep Earth aquifers, and is one of the major pathways for metabolising iron in nature. Organic matter containing quinone groups can act as electron shuttles to transfer electrons between microorganisms and Fe(III) oxides, facilitating the biotransformation of iron; this process also influences the transport transformation of pollutants. In this paper, the reduction of Fe(III) oxides by aniline in the heterogeneous iron-reducing bacterium Shewanella oneidensis MR-1 mediated by the electron shuttle AQS was investigated. The results showed that aniline significantly promoted the reduction of Fe(III) by MR-1 in the AQS-mediated reaction, and the best Fe(III) reduction was achieved in the reaction group of "GT+MR-1+0.5mM AQS+3μM aniline", in which the Fe(II) production was significantly higher than that in the reaction groups of only microorganisms and no aniline reaction. The amount of Fe(II) produced was significantly higher than that of the microorganism-only and aniline-free reaction groups, and the addition of aniline also significantly increased the consumption of sodium lactate by MR-1 in the reaction system. The solid mineral Fe(II)-O content increased to 41.32% after the reaction. However, the structure of needle ferrite is relatively stable, and the surface morphology did not change significantly by SEM, and the generation of other secondary minerals was not observed in the XRD results. The results of this experimental study can help to understand the biogeochemical cycle of iron in multicomponent reactions and are of great significance for environmental management.

Fe- and Al-rich metapelite from the Transangarian segment of the Yenisey Ridge (East Siberia, Russia) is a potential new source of high-alumina refractories. The rocks have relatively high average contents of Al2O3 (20 wt.%) and Fe2O3 (7.91 wt%), moderate K2O (3.44 wt%), and low CaO (0.74 wt%). Their dominant mineral assemblages are andalusite + muscovite + margarite + chlorite + biotite + quartz or staurolite + kyanite or/and andalusite + chlorite + muscovite + biotite + quartz with ±garnet and ±plagioclase. Al2SiO5 polymorphs occur as up to 1.5 cm andalusite porphyroblasts and partial or complete pseudomorphs after andalusite (kyanite and staurolite). Accessories include abundant Fe-Ti oxides and sporadic REE-, Y-, Ca-phosphates; sulfides are negligible. The composition of Al2SiO5 concentrates obtained in laboratory by heavy-media and magnetic separation from ≥0.06 mm fractions meet all requirements for raw material of this type: &gt;56 wt% Al2O3, &lt;42 wt% SiO2, &lt;1 wt% Fe2O3, &lt;1.2 wt% TiO2, and &lt;0.2 wt% (CaO+MgO). The andalusite, kyanite, and mixed ores yield 0.7-4.1 wt%, 0.7-2.2 wt%, and 1.9-6.0 wt% of concentrate, respectively. The best-quality ores rich in Al2SiO5 polymorphs reside in zones of contact and/or dynamic metamorphism superimposed over regional metamorphism of Al-rich rocks.

Antibiotic residues in aquatic environment have the possibility to induce resistance in environmental bacteria, which ultimately might get transferred to pathogens making treatment of diseases difficultand poses a serious threat to public health. If antibiotic residues in the environment can be eliminated or reduced, it has the possibility to contribute antibiotic resistance. Towards this objective, water containing ciprofloxacin was treated with sunlight assisted photocatalysis using Fe doped ZnOnanoparticles for assessing the degradation potential of this system.Parameters like pH, temperature, catalytic dosage were assessed for the optimum performance of the system. To evaluate degradation of ciprofloxacin,both spectrophotometricas well as microbiological (loss of antibiotic activity)methods were employed. 100 mg/L Fe doped ZnO nanoparticle catalyst and sunlight intensity of 120,000–135,000 lux system gave optimum performance at pH 9 at 30 °C and 40 °C. At these conditions spectrophotometric analysis showed complete degradation of ciprofloxacin (10mg/L) by 210 min. Microbiological studies showed loss of antibacterial activity of the photocatalytically treated ciprofloxacin containingwater against Staphylococcus aureus (10⁸ CFU) in 60 min and for Escherichia coli (10⁸ CFU) in 75 min. Thedeveloped system, thus possess a potential for treatment of antibiotic contaminated waters for eliminating/reducing antibiotic residues from environment.

The accurate quantification of $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios for Mössbauer spectroscopic room temperature measurements involves many steps and, when shown in a composite Mössbaur data table, does not allow enough space for more Mössbauer parameters to be presented in the composite table. So a simple formula is derived, (presented as a short communication) which users will find helpful when they have to determine corrected $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios in their room temperature Mössbauer experiments.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

Laser shock peening is a process which can reduce stress corrosion cracking and improve fatigue life by forming compressive residual stress on the surface of the material. In a computational FE simulation of laser shock peening, during applying the pressure load generated by the laser pulse to the surface of simulation geometry, the peening is simulated by explicit analysis and then convert to implicit analysis to dissipate the dynamic energy remaining in the geometry. In this study, static damping is applied to dissipate residual dynamic energy without converting it into an implicit analysis. The compressive residual stress distribution is compared between the simulation results for the stainless steel 304 material and the same material subjected to actual laser shock peening. The laser shock peening parameters were 4.2J laser pulse energy, 50% overlap of 3mm diameter of the laser beam and water as a confinement layer. As a result, the compressive residual stress from the surface to the depth direction is similar to both the simulation and the experimental result measured by the hole drilling method.

This paper presents results from numerical and experimental investigation on Charpy tests in order to point out failure mechanisms and to evaluate new polymeric blends PP+PA6+EPDM. Charpy tests were done for initial velocity of the impactor of 0.96 m/s and its mass of 3.219 kg and these data were also introduced in the finite element model. The proposed model take into account the system of four balls, including support and the ring of fixing the three balls and it has a finer discretization of the impact area to highlight the mechanisms of failure and their development in time. The constitutive models for four materials (polypropylene with 1% Kritilen, two blends PP+PA6+EPDM and a blend PA6+EPDM) were derived from tensile tests. Running simulations for each constitutive model of material makes possible to differentiate the destruction mechanisms according to the material introduced in the simulation, including the initiation and the development of the crack(s), based on equivalent plastic strain at break (EPS) for each material. The validation of the model and the simulation results was done qualitatively, analysing the shape of broken surfaces and comparing them to SEM images and quantitatively by comparing the impact duration, energy absorbed by the sample, the value of maximum force during impact. The duration of the destruction of the specimen is longer than the actual one, explainable by the fact that the material model does not take into account the influence of the material deformation speed in Charpy test, the model being designed with the help of tests done at 0.016 m/s (1000 mm/min) (maximum strain rate for the tensile tests). Experimental results are encouraging for recommending the blends 20% PP+42% PA6+28% EPDM and 60% PA6+ 40%EPDM as materials for impact protection at low velocity (1m/s). Simulation results are closer to the experimental ones for the more brittle tested materials (with less content of PA6 and EPDM) and more distanced for the more ductile materials (with higher content of PA6 and EPDM).

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

The efficiency and performance of Proton Exchange Membrane Fuel Cells (PEMFCs) are primarily influenced by ORR electrocatalysts. In recent years, atomically dispersed met-al-nitrogen-carbon (M-N-C) catalysts have gained significant attention due to their high active center density, high atomic utilization, and high activity. These catalysts are now considered the preferred alternative to traditional noble metal electrocatalysts. The unique properties of M-N-C catalysts are anticipated to enhance the energy conversion efficiency and lower the manufac-turing cost of the entire system, thereby facilitating the commercialization and widespread ap-plication of fuel cell technology. This article initially delves into the origin of performance and degradation mechanisms of Fe-N-C catalysts from both experimental and theoretical perspectives. Building on this foundation, the focus shifts to strategies aimed at enhancing the activity and durability of atomically dispersed Fe-N-C catalysts. These strategies encompass the use of bi-metallic atoms, atomic clusters, heteroatoms (B, S, and P), and morphology regulation to optimize catalytic active sites. The article concludes by detailing the current challenges and future pro-spects of atomically dispersed Fe-N-C catalysts.

The current work investigates the auxetic tensile deformation behavior of the inversehoneycomb structure with 5 × 5 cells made of biodegradable poly(butylene adipate-coterephthalate) (PBAT). Fused deposition modeling, an additive manufacturing method, produced such specimens. Residual stress (RS) and warpage, more or less, always exist in such specimens due to layer-by-layer fabrication, i.e., repeated heating and cooling. The RS influences the auxetic deformation behavior, but its measurement is challenging due to the very fine structure. Instead, the finite-element(FE)-based process simulation realized by an ABAQUS plug-in numerically predicts the RS and warpage. The predicted warpage shows a negligible slight deviation compared to the design topology. This process simulation also delivers the temperature evolution of a small volume material, revealing the local cyclic heating and cooling. The achieved RS serves as the initial condition for the FE model used to investigate the auxetic tensile behavior. With the outcomes from FE calculation without considering RS at hand, the effect of the RS on the deformation behavior is discussed for the global force-displacement curve, the structural Poisson’s ratio evolution, the deformed structural status, the stress distribution, and evolution, where the first three and the warpage are also compared with experimental results. Furthermore, the FE simulation can easily provide the global stress-strain flow curve with the total stress calculated from the elemental ones.

Using optical characterization, it is evident that the spin state of the spin crossover molecular complex [Fe{H2B(pz)2}2(bipy)] (pz = tris (pyrazol-1-1y)-borohydride, bipy = 2,2’-bipyridine) depends on the ferroelectric polarization of an adjacent thin film of the polymer ferroelectric polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP). The UV-Vis spectroscopy reveals that room temperature switching of [Fe{H2B(pz)2}2(bipy)] molecules in bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] as a function of ferroelectric polar polarization. The electric polarity dependence of bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] shows a strong dependence on the thickness of the PVDF-HFP layer. The PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] interface may affect polarization retention in the PVDF-HFP thin film limit.

Zn–Ni plating is indispensable in various industries because of its high corrosion resistance. However, Ni has been reported to trigger allergies; thus, an alternative Ni-free plating is desired. Zn–Fe plating is considered to be a promising candidate, albeit its corrosion resistance still needs to be improved. The corrosion resistance of Zn–Fe plating is expected to increase by the addition of Mo as the third alloying element as it is more noble than Zn and Fe. In this study, Zn–Fe–Mo plating with a corrosion resistance nearly equivalent to that of the Zn–Ni plating was fabricated. Zn–Fe–Mo plating was electrically deposited from continuously agitated plating baths prepared by mixing ZnSO₄, FeSO₄, Na₂MoO₄, Na₃C₆H₅O₇, and Na₂SO₄ using Fe or Ni plates as the substrate. The surface morphology, composition, crystal phase, and electronic state of Mo of the platings were investigated by SEM-EDS, XRD, and XPS. The anti-corrosion performance was evaluated by Tafel extrapolation method. Formation of plating comprising a Mo containing alloy phase was found to be crucial for improving corrosion resistance. The Zn–Fe–Mo plating demonstrates promise for replacing anti-corrosion Zn–Ni platings.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

Near-infrared (NIR) photodetectors (PDs) have attracted much attention in noninvasive medical diagnosis and treatment. Especially, the self-filtered NIR PDs are highly demandable for tremendous biomedical application due to their strong ability in wavelength discrimination. In this work, we designed and then fabricated a Si micro-holes array/Graphene (Si MHA/Gr) van der Waals (vdW) Schottky NIR photodiode by using PbS quantum dots (QDs) coating. The device exhibits a unique self-filtered NIR response with a responsivity of 0.7 A/W at -1 V and a response time of 61 μs, which are higher than that without PbS QDs coating and even most of previous Si/Gr Schottky photodiodes. The light trapping of the Si MHA and the PbS QDs coating can be attributed to the high responsivity of the vdW photodiode. Furthermore, the presented NIR photodiode can also be integrated in photoplethysmography (PPG) for real-time heart-rate (HR) monitoring. The extracted HR is in great accord with the value measured with the patient monitor by analyzing the Fourier transform of the stable and reliable fingertip PPG waveform, suggesting its potential for practical applications.

Thermal fluctuations in two-dimensional (2D) isotropy systems at non zero finite temperatures can destroy the long-range (LR) magnetic order due to Mermin-Wanger theory. Interestingly, the magnetic anisotropy related to spin-orbit coupling (SOC) could stabilize magnetic order in 2D systems. Recently, 2D FexGeTe2 (3≤x≤7) with high curie temperature (TC), as a typical 2D van der Waals metallic ferromagnet, has not only made significant progress in synthetic methods and controlling ferromagnetism (FM), but also actively explored many device applications. In this Review, we introduce six experimental methods, ten ferromagnetic modulation strategies, and three spintronic devices of 2D FexGeTe2 materials. Overall, we have outlined the challenges and potential research directions in this field.

In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

The spectra currently emerging from modern ground- and space-based astronomical instruments are of exceptionally high quality and resolution. To meaningfully analyse these spectra researchers utilise complex modelling codes to replicate the observations. The main inputs to these codes are atomic data such as excitation and photoionisation cross sections as well as radiative transition probabilities, energy levels and line strengths. In this publication the current capabilities of the numerical methods and computer packages used in the generation of these data are discussed. Particular emphasis is given to Fe-peak species and the heavy systems of tungsten and molybdenum. Some of the results presented to highlight certain issues and/or advances have already been published in the literature, while other sections present, for the first time, new recently evaluated atomic data.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Objective: To use the ancient and modern medical record cloud platform (V2.3.5) to organize and explore the medication patterns of the "Three Causes, Extremity, and One Disease Syndrome Formula" by Chen Wuxuan, and to summarize its therapeutic ideas. Method: Collect and organize the "San Yin Si Tian Fang" in the "San Yin Ji Yi Zheng Fang Lun", and use the modern medical record cloud platform (V2.3.5) to conduct medication frequency statistical analysis, cluster analysis, and complex network analysis. As a result, a total of 16 Chinese herbal medicines were collected in the "Three Causes, Extreme and One Disease Syndrome Formula", involving 75 traditional Chinese medicines. Statistical analysis showed that roasted licorice was the most commonly used, followed by Pinellia ternata, papaya, ginger, and Poria cocos; Medications mainly include warm drugs, sweet and pungent flavors, as well as drugs that promote lung and spleen meridians. Cluster analysis can divide the above-mentioned traditional Chinese medicine into two groups, with specific grouping as follows. Group 1: ginger, white peony, aconite, papaya, and achyranthes bidentata; Group 2: roasted licorice, poria cocos, dried ginger, pinellia ternata, and green peel. Conclusion: The characteristics of the 16 prescriptions are biased towards Xin Gan Wen, emphasizing the regulation of the spleen and stomach, which may be related to the common use of prescription by doctors in the Song Dynasty and the tendency towards warm and dry medication.

In this study, we evaluated the antibacterial effect against Staphylococcus aureus and Salmonella Typhimurium in fried fish paste using floating electrode-dielectric barrier discharge (FE-DBD) plasma (1.1 kV, 43 kHz, N2 1.5 m/s, 1-60 min). In addition, quality evaluation (pH, VBN) of fried fish paste was conducted after FE-DBD plasma treatment. When FE-DBD plasma was treated for 1, 5, 10, 20, 30 and 60 min, S. aureus decreased by 0.16-1.13 log10 CFU/g, and S. Typhimurium decreased 0.25-1.13 log10 CFU/g. Both decreased &gt; log10 CFU/g at 60 min. The D-value was 58.92 and R2 was 0.97 for S. aureus using first-order kinetics, and the D-value was 43.60 and R2 was 0.97 for S. Typhimurium using the Weibull model. There was no significant difference in pH after FE-DBD plasma treatment (p &gt; 0.05). However, volatile basic nitrogen (VBN) significantly decreased as the treatment time increased (p &lt; 0.05), and it was the lowest at 60 min to 3.46. Therefore, FE-DBD plasma treatment could be considered as a technology for preserving the quality of processed foods.

: This article reports on polymer (PLLA, poly(L-lactic acid)) nanosheets incorporated with Fe-ion nanoparticles, aiming at using the latter nanoparticles as source to release Fe ions to facilitate burn wound healing when such nanosheets are applied on skin as biomedical tissue. Laser ablation in liquid phase was used to produce Fe-containing nanoparticles that after incorporation into PLLA nanosheets would release Fe ions when in immersed in water. Such nanoparticles prepared in chloroform are shown by XPS to be based on iron chloride and oxide phases. After incorporation into PLLA nanosheets, the ion –release test demonstrated that Fe ions could be released successfully into water at pH 7.4, which implies that such polymer nanosheets show promise for biomedical applications as potential patches for healing burn wounds. Incorporation with two different metal ions (Fe and Zn) is shown to be efficient and both types of ions were demonstrated to be released simultaneously and with comparable release rates.

: The article examines the regularities of structure formation of ultrafine fibers based on poly-3-hydroxybutyrat under the influence of technological (electrical conductivity, viscosity), molecular (molecular weight), and external factors (low-molecular and nanodispersed substances of different chemical nature). Systems with polar substances are characterized by the presence of intermolecular interactions and the formation of a more perfect crystalline fiber structure. Changes in technological and molecular characteristics affect the fiber formation process, resulting in alterations in the morphology of the non-woven fabric, fiber geometry, and supramolecular fiber structure. Polymer molecular weight, electrical conductivity, and solution viscosity influence fiber formation and fiber diameter. The fiber structure is heterogeneous, consisting of both crystalline and non-equilibrium amorphous phases. This is significant in the development of matrix-fibrillar systems for drug delivery, bioactive substances, antiseptics, tissue engineering constructs, tissue engineering scaffolds, artificial biodegradable implants, sorbents, and other applications.

Iron-based materials are widely applied in Fenton chemistry and they have promising prospects in the processing of wastewater. The composition complexity and rich chemistry of iron and/or oxides, however, hamper the precise understanding on the active sites and the working mechanism which still remain highly controversial. Herein, iron oxides of four different model systems are designed through a conventional precipitation method plus H2 reduction treatment. These systems feature Fe@Fe3O4 with abundant oxygen vacancy, Fe0 and Fe3O4 particles with interface structures, and Fe3O4-dominated nanoparticles of different sizes. These materials are applied in the decomposition of methyl orange as a model reaction to assess the Fenton chemistry. The Fe@Fe3O4 with core-shell structures exhibited significantly higher decomposition activity than the other Fe3O4-rich nanoparticles. A thin Fe3O4 layer formed by auto-oxidation of iron particles when exposing to air can boost the activity as compared with the Fe0 and Fe3O4 particles with interface structures but poor oxygen vacancy. The unique hetero-structure with the co-existence of both metallic iron and oxygen vacancy displayed excellent redox propensity which might account for the superior Fenton activity. This finding provides a new perspective to understand and design highly efficient iron-based Fenton catalysts.

Concern over potential antimony mediated toxicity from mining and smelting activities has instigated novel concepts toward removing aqueous antimony ions. The iron based adsorbent Fe3O4/HCO was found to be efficient for treating antimony-containing wastewater However, ineffective methodology for preparation limited its effective adsorption capacity and thus wider application. In this study, a new type of HCO-doped-(Fe3O4)x adsorbent was prepared by co-precipitation method for doping Fe3O4 into HCO sludge (HCO), thereby improving adsorption performance for Sb(III) and Sb(V) ions, with the maximum adsorbing capacity being 44.46 mg/g and 47.91 mg/g, respectively. According to the results of BET, SEM-EDS, XRD and XPS, it were confirmed that the FeOOH and X≡Fe-OH were formed during the preparation process, bring about the increased the surface area, thus resulting in further increase of surface area, hydroxyl groups and the net negative ionic charge. Moreover, the adsorption kinetics followed the pseudo-second-order kinetic model which indicated that adsorption process of Sb(III)/Sb(V) by HCO-doped-(Fe3O4)x adsorbent was controlled by chemical reaction. The main adsorption mechanism is that antimony ion and amorphous iron oxide X≡Fe-OH undergo coordination exchange reaction and complexation reaction with CeO2 or Ce2O3. Furthermore, HCO-doped-(Fe3O4)x could adapt to wide pH and had stable adsorption ability after regeneration. The good adsorption performance of HCO-doped-(Fe3O4)x makes it a potential applications of adsorbent for removal of antimony.

Climate change and environmental degradation are major threats to sustainable agricultural development in Southern Africa. Thus, the concept of sustainable intensification (SI) i.e. getting more output from less input using certain practices such as agroforestry, organic fertilizer, sustainable water management etc. has become an important topic among researchers and policy makers in the region in the last three decades. A comprehensive review of literatures on the adoption of SI in the region identify nine relevant drivers of adoption of SI among (smallholder) farmers. These drivers include (i) age, (ii) size of arable land, (iii) education, (iv) extension services, (v) gender, (vi) household size, (vii) income, (viii) membership in farming organization and (ix) access to credit. We present the results of a meta-analysis of 21 papers on the impact of these determinants on SI adoption among (smallholder) farmers in Southern African Development Community (SADC) using random-effects estimation techniques for the true effect size. While our result suggests that variables such as extension services, education, age, and household size may influence the adoption of SI in SADC, factors such as access to credit is also of great importance. Decision-makers should therefore concentrate efforts on these factors in promoting SI across the SADC. This includes increasing the efficiency of public extension service as well as involvement of private sector in extension service. Furthermore, both public and private agriculture financing models should consider sustainability indicators in their assessment process.

Parkinson’s Disease (PD) is a neurodegenerative and progressive disease that impacts the nerve cells in the brain and varies from person to person. The exact cause of PD is still unknown, and the diagnosis of PD does not include a specific objective test with certainty. Although deep learning has made great progress in medical neuroimaging analysis, these methods are very susceptible to biases present in neuroimaging datasets. An innovative decorrelated deep learning technique is introduced to mitigate class bias and scanner bias while simultaneously focusing on finding distinguishing characteristics in resting-state functional MRI (rs-fMRI) data, which assist in recognizing the PD with good accuracy. The decorrelation function reduces the non-linear correlation between features and bias in order to learn bias-invariant features. The Parkinson’s Progression Markers Initiative (PPMI) dataset, referred to as a single scanner imbalanced dataset in this study used to validate our method. The imbalanced dataset problem affects the performance of the deep learning framework by overfitting to the majority class. To resolve this problem, we propose a new Decorrelated Convolutional Neural Networks (DcCNN) framework by applying decorrelation-based optimization to Convolutional Neural Networks(CNN). An analysis of evaluation metrics comparisons shows that integrating the decorrelation function boosts the performance of PD recognition by removing class bias. Specifically, our DcCNN model performs significantly better than existing traditional approaches to tackle the imbalance problem. Finally, the same framework can be extended to create scanner invariant features without significantly impacting the performance of a model. The obtained dataset is a multi-scanner dataset which leads to scanner bias due to the differences in acquisition protocols and scanners. The multi-scanner dataset is a combination of two datasets, namely PPMI and FTLDNI - frontotemporal lobar degeneration neuroimaging initiative (NIFD) dataset. The results of t-distributed stochastic neighbor embedding (t-SNE) and scanner classification accuracy of our proposed Feature Extraction-DcCNN (FE-DcCNN) model validated the effective removal of scanner bias. Our method achieves an average accuracy of 77.80% on a multi-scanner dataset for differentiating PD from healthy control, which is superior to the DcCNN model trained on a single scanner imbalanced dataset.

Keywords: Wall-like RC columns; Strengthening; FRP; NSM rebars; Steel plates; Testing; FE modeling; Preloading.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

The authors of the article performed computer simulation of buffer amplifiers (BA), which have medium and extremely small values of the offset voltage's systematic component (V_off), for different technological processes (Si, GaAs and GaN). The proposed control units are distinguished by a small number of elements and allow operation in the range of low and high temperatures. The variants of circuitry implementation of control units based on GaAs, GaN depletion-mode CMOS and JFET technological processes are considered. The results of the comparative modeling showed that the basic circuit of the BA on two field-effect transistors, when implemented on various modifications of GaN MOS and depletion-mode MOS transistors, provides sufficiently low values of the offset voltage's systematic component (less than 2 μV). The proposed BAs are designed for use in the structure of the Sallen-Key low-pass filter (LPF) when they are implemented both on mid-frequency Si CJFET and on GaAs microwave transistors. Low values of the LPF V_off have a positive effect on the effective capacity of the ADC. An example of switching on a BA in the JFET OpAmp structure based on the depletion-mode MOS input stage and a “folded” cascode, which, with 100% negative feedback, can be used in the Sallen-Key LPF, is considered. Computer simulation of the JFET/MOS OpAmp showed that the OpAmp has an open-loop voltage gain of 76-85dB, and its V_off is within 7µV in the temperature range from -60°C to +120°C. The presented circuitry of buffer amplifiers is intended, first of all, for the tasks of designing precision Sallen-Key low-pass filter (low-pass filter, high-pass filter, PF, RF).

A series of defective ZSM-5 zeolites (~300 nm, SiO₂/Al₂O₃ ratio of 55, 100, 400 and 950) were intentionally prepared and systematically studied by XRD, SEM, ²⁹Si MAS NMR, argon physisorption, NH₃-TPD and FT-IR technologies. The nature, the amount and the accessibility of the acid sites of defective ZSM-5 zeolites are greatly different from reported ZSM-5 zeolites with perfect crystal structure. The co-existed strong Brønsted acid sites (Si(OH)Al) and weak Brønsted acid sites (hydroxyl nests) over defective ZSM-5 zeolites might lead to unique catalytic function. Zn(C₂H₅)₂ was grafted onto defective ZSM-5 zeolites through chemical liquid deposition (CLD) method. Interestingly, FT-IR spectroscopy studies find that Zn(C₂H₅)₂ was preferentially grafted on the hydroxyl nests with weak acidity rather than the Si(OH)Al groups with strong acidity over different defective ZSM-5 zeolites. Particularly, home-built operando dual beam FTIR-MS was applied to study the catalytic performance of Zn species locating at different sites of defective ZSM-5 zeolites under n-hexane transformation. Results show that Zn species grafted over hydroxyl nests obtain better dehydrogenation performance than Zn species over framework aluminum. This study provides guidance for the rational design of highly efficient alkane dehydrogenative aromatization catalysts.

In this study, Fe-based superconductors (SCs) are described with a model showing a novel attractive force. First, we describe this novel force using an analog from electromagnetism. From electromagnetism, it was found that this force is a Lorentz force in which two electrons orbit around a Fe-ion with the same velocity. Then, we consider a wave function of an electron. Consequently, due to the property of the proposed attractive force and the quantum-field Hamiltonian, we clarified that the Bardeen–Cooper–Schrieffer (BCS) ground state can be reused. Afterward, attractive force energy was calculated according to the presented model. In Fe-based SCs, a structure transition is essential. Considering that the derived attractive force energy is relatively large, we employ the expanded T_c-equation from the BCS theory that includes the structure transition effect and the derived attractive force energy. In addition, we succeed in analytically reproducing T_c-dome diagrams in various types of Fe-based SCs. Moreover, we discuss the universal property a general SC should have as well as the quantum critical point.

Fire is a significant threat to human life and civil infrastructures. Builders and architects are hankering for safer and sustainable alternatives of concrete that do not compromise with their design intent or fire safety requirements. The aim of the present work is to improve the residual compressive performance of concrete in the post-fire exposure, by incorporating by-products from urban residues. Based on sustainability and circular economy motivations, the attention is focused on rubber tire fly ash, aged brick powder, and plastic (PET) bottle residuals used as partial sand replacement. The selected by-products from urban residues are used for the preparation of Cement-Based Composites (CBCs) in two different proportions (10 % and 15 %). The thermal CBC behaviour is thus investigated under realistic fire scenarios (i.e., Direct Flame (DF) for 1 hour (1h)), by following the ISO 834 standard provisions, but necessarily resulting in non-uniform thermal exposure for the cubic specimens. The actual thermal exposure is further explored with a Finite Element (FE) model, giving evidence of thermal boundaries effects. The post-fire residual compressive strength of heated concrete and CBC samples is hence experimentally derived, and compared to unheated specimens in ambient conditions. From the experimental study, the enhanced post-fire performance of CBCs with PET bottle residual is generally found superior to other CBCs or concrete. The structure-property relation is also established, with the support of Scanning Electron Microscopy (SEM) micrographs. Based on existing empirical models of literature for the prediction of the compressive or residual compressive strength of standard concrete, newly developed empirical relations for both concrete and CBCs are assessed.

: Sputtering of silicon in a Helium magnetron discharge (MS) has been reported as a bottom-up procedure to obtain He-charged silicon films (i.e. He nanobubbles encapsulated in a silicon matrix). The incorporation of heavier noble gases is demonstrated in this work with a synergistic effect producing increased Ne and Ar incorporations when using He-Ne and He-Ar gas mixtures in the MS process. Microstructural and chemical characterizations are reported by ion beam analysis (IBA) and scanning and transmission electron microscopies (SEM and TEM). In addition to gas incorporation, helium promotes the formation of larger nanobubbles. For the case of Ne high resolution X-ray photoelectron and absorption spectroscopies (XPS and XAS) are reported with remarkable dependence of the Ne 1s photoemission and the Ne K-edge absorption on the nanobubbles size and composition. The gas (He, Ne, Ar) charged thin films are proposed as “solid” targets for the characterization of spectroscopic properties of noble gases in a confined state without the need for cryogenics or high-pressure anvils devices. Also their use as targets for nuclear reaction studies is foreseen.

Two novel core-shell composites SiO2@PMDA-Si-Tb, SiO2@PMDA-Si-Tb-phen with SiO2 as the core and terbium organic complex as the shell, were successfully synthesized. The terbium ion was coordinated with organic ligand forming terbium organic complex in the shell layer. The bi-functional organosilane ((HOOC)2C6H2(CONH(CH2)3Si(OCH2CH3)3)2 (abbreviated as PMDA-Si) was used as the first ligand and phen as the second ligand. Furthermore, the silica-modified SiO2@PMDA-Si-Tb@SiO2, SiO2@PMDA-Si-Tb-phen@SiO2 core-shell-shell composites were also synthesized by sol–gel chemical route. An amorphous silica shell was coated around the SiO2@PMDA-Si-Tb and SiO2@PMDA-Si-Tb-phen core-shell composites. The core-shell and core-shell-shell composites both exhibited excellent luminescence in solid state. The luminescence of core-shell-shell composites was stronger than that of core-shell composites. Meanwhile, an improved luminescence stability property for the core-shell-shell composites was found in the aqueous solution. The core-shell-shell composites exhibited bright luminescence, high stability, long lifetime, and good solubility, which may present potential applications in the field of bio-medical.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

The process of anaerobic digestion used for methane production can be enhanced by incorporating stimulating materials. The effects of these materials are dependent on various factors including the processed substrate, process conditions, and the type and amount of the stimulating material used. As part of the study, three different stimulating materials - iron powder, lime, and milled porous ceramic - were added to the 30-day anaerobic digestion of the brewer's spent grain to improve its performance. Different doses ranging from 0.2 to 2.3 gTS×L-1 were tested, and methane production kinetics were determined using the first-order model. The results showed that the methane yield ranged from 281.4±8.0 to 326.1±9.3 ml×gVS-1, while substrate biodegradation ranged from 56.0±1.6 to 68.1±0.7%. The addition of lime reduced methane yield at almost all doses by -6.7% to -3.3%, while the addition of iron powder increased methane yield from 0.8% to 9.8%. The addition of ceramic powder resulted in a methane yield change ranging from -2.6% to 4.6%. These findings suggest that the use of stimulating materials should be approached with caution, as even slight changes in the amount used can impact methane production.