Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Stroke often results in impaired gait, which can limit community ambulation and the quality of life. Recent works have shown the feasibility of transcranial Direct Current Stimulation (tDCS) as an adjuvant treatment to facilitate gait rehabilitation. Since the cerebellum plays an essential role in balance and movement coordination, which is crucial for independent overground ambulation, so, we investigated the effects of cerebellar tDCS (ctDCS) on the post-stroke overground gait performance in chronic stroke survivors. Fourteen chronic post-stroke male subjects were recruited based on convenience sampling at the collaborating hospitals where ten subjects finally participated in the ctDCS study. We evaluated the effects of two ctDCS montages with 2mA direct current, a) optimized configuration for dentate stimulation with 3.14cm² disc anode at PO10h (10/5 EEG system) and 3.14cm² disc cathode at PO9h (10/5 EEG system), and b) optimized configuration for leg lobules VII-IX stimulation with 3.14cm² disc anode at Exx8 (electrodes defined by ROAST) and 3.14cm² disc cathode at Exx7. We found ctDCS to be acceptable by all the exposed subjects. The ctDCS intervention had an effect on the 'Normalised Step length Affected side' (p=0.1) and 'Gait Stability Ratio' (p=0.0569), which was found using Wilcoxon signed-rank test at 10% significance level. Also, ctDCS montage specific effect was found using a two-sided Wilcoxon rank-sum test at a 5% significance level for 'Step Time Affected Leg' (p=0.0257) and '%Stance Time Unaffected Leg' (p=0.0376). Moreover, the changes in the quantitative gait parameters across both the montages were found to be correlated to the mean electric field strength in the lobules based on partial least squares regression analysis (R² statistic = 0.6574) where the mean electric field strength at the cerebellar lobules, Vermis VIIIb, Ipsilesional IX, Vermis IX, Ipsilesional X, had the most loading. In conclusion, our feasibility study indicated the potential of a single session of ctDCS to contribute to the immediate improvement in the balance and gait performance in terms of gait-related indices and clinical gait measures.

Nuclear Magnetic Resonance (NMR) and its various forms are extensively utilized in both research and clinical settings to analyse molecules. NMR data pre-processing, while essential to NMR data analysis, can be uniquely complex. Despite the availability of software tools, understanding these processes can be challenging, complicating the selection of appropriate pre-processing steps. In this review, we elucidate pre-processing steps in the time domain from a mathematical and statistical perspective, explaining direct current offset removal, eddy current correction, shift and linear prediction, weighting, zero filling, and domain transformation using plain language and fundamental mathematical formulas. Our objective is to clarify these processes in simple terms and provide general guidance.

Indonesia's SUMBAGUT 150 kV transmission of High Voltage Alternating Current Network (HVAC) system has considerable power losses. These power losses are a critical problem in the transmission network system. Meanwhile, this study provides one solution to reduce power losses using a High Voltage Direct Current (HVDC) network system. Determining the location to convert HVAC into HVDC is very important. The authors use Particle Swarm Optimization (PSO) to get the optimal location on the 150 kV SUMBAGUT HVAC transmission network system. The study results showed that before using the HVDC network system, the power losses were 122.26 MW. Meanwhile, power losses with one transmission HVDC in the "Paya Pasir-Sei Rotan" are 84.16 MW, "Porsa-P. Siantar" 90.83 MW, "Paya Pasir-Paya Geli" 104.14 MW. Then power losses with two transmission HVDC in "Paya Pasir-Sei Rattan" and "Porsa-P. Siantar" is 71.24 MW, "Paya Pasir-Sei Rotan" and "Paya Pasir-Paya Geli" 77.46 MW, "Porsa-P. Siantar" and "Paya Pasir-Paya Geli" 78.52 MW. The last result, power losses with three transmission HVDC in "Paya Pasir-Sei Rotan," "Porsa-P. Siantar," and "Paya Pasir-Paya Geli" lost 64.57 MW.

Objective: Cerebrovascular accidents are the second leading cause of death and the third leading cause of disability worldwide. We hypothesized that cerebellar transcranial direct current stimulation (ctDCS) of the dentate nuclei and the lower-limb representations in the cerebellum can improve standing balance functional reach in chronic (> 6 months’ post-stroke) stroke survivors. Materials and Methods: Magnetic resonance imaging(MRI) based subject-specific electric field was computed across 10 stroke survivors and one healthy MRI template to find an optimal bipolar bilateral ctDCS montage to target dentate nuclei and lower-limb representations (lobules VII-IX). Then, in a repeated-measure crossover study on 5 stroke survivors, we compared 15minutes of 2mA ctDCS based on the effects on successful functional reach(%) during standing balance task. Three-way ANOVA investigated the factors of interest– brain regions, montages, stroke participants, and their interactions.Results: “One-size-fits-all” ctDCS montage for the clinical study was found to be bipolar PO9h – PO10h for dentate nuclei and bipolar Exx7–Exx8 for lobules VII-IX with contalesional anode. Bipolar PO9h–PO10h ctDCS performed significantly (alpha=0.05) better in facilitating successful functional reach (%) when compared to bipolar Exx7–Exx8 ctDCS. Furthermore, a linear relationship between successful functional reach (%) and electric field strength was found where bipolar PO9h–PO10h montage resulted in a significantly (alpha=0.05) higher electric field strength when compared to bipolar Exx7–Exx8 montage for the same 2mA current. Conclusion: We presented a rational neuroimaging based approach to optimize deep ctDCS of the dentate nuclei and lower limb representations in the cerebellum for post-stroke balance rehabilitation.

With the proportional reduction of MOSFET size, the leakage-to-barrier reduction (DIBL) effect leads to a more significant increase in the tunneling current on the gate, and the appearance of the gate tunneling current also seriously affects the static characteristics of the device. In this paper, a new theoretical model of the relationship between the direct tunneling current and the thickness of the oxide layer under the DIBL effect is proposed for the MOSFET device with ultra-thin oxide layer. On this basis, the characteristics of the MOSFET device are studied in detail by using HSPICE, and their working conditions are quantitatively analyzed. The characteristic variation trend of small-size devices under the influence of gate tunneling current is predicted. The simulation results using BSIM4 model are consistent with the theoretical model. The theory and data in this paper will provide useful reference for large scale integrated circuit design.

Background. False memories tend to increase in healthy and pathological aging, and their reduction could be useful in improving cognitive functioning. The objective was to use an active-placebo method to verify whether the application of tDCS in improving true recognition and reducing false memories in healthy older people. Method. Participants were 29 healthy older adults (65-78 years old) assigned to active or placebo group; active group received anodal stimulation at 2mA for 20 min over F7. An experimental task was used to estimate true and false recognition. The procedure took place in two sessions on two consecutive days. Results. A mixed ANOVA of true recognition showed a significant main effect of session (p = .004), indicating an increase from before treatment to after it. False recognition showed a significant main effect (p = .004), indicating a decrease from before treatment to after it and a significant session x group interaction (p < .0001). Conclusions. Overall, our results show that tDCS is an effective tool for increasing true recognition and reducing false recognition in healthy older people, and suggest that stimulation improves recall by increasing the number of items a participant can recall and reducing the number of memory errors.

The battle of currents between AC and DC reignited as a result of the development in the field of power electronics. The efficiency of DC distribution systems is highly dependent on the efficiency of distribution converter, which calls for optimized schemes for efficiency enhancement of distribution converters. Modular solid-state transformers play a vital role in DC Distribution Networks and Renewable Energy systems (RES).This paper deals with efficiency-based load distribution for Solid State Transformers (SSTs) in DC distribution networks. Aim is to achieve a set of minimum inputs that are consistent with output while considering constraints and efficiency. As the main feature of modularity is associated with a three-stage structure of SSTs. This modular structure has been optimized using Ant Lion Optimizer (ALO) and validated by applying it EIA (Energy Information Agency) DC Distribution Network which contains SSTs. In the DC distribution grid, modular SSTs provide promising conversion of DC power from medium voltage to lower DC range (400V). The proposed algorithm is simulated in MATLAB and also compared with two other metaheuristic algorithms. The obtained results prove that the proposed method can significantly reduce input requirements for producing the same output while satisfying the specified constraints.

ADHD, a neurodevelopmental condition, is distinguished by a triad of symptoms including inattention, hyperactivity, and impulsivity. It is frequently accompanied by comorbidities such as anxiety, depression, and learning disabilities. As a result, clinicians often face challenges in accurately diagnosing ADHD and differentiating it from other conditions. As a prospective remedy for ADHD, scientists have investigated Transcranial Direct Current Stimulation (tDCS), a non-invasive technique of stimulating the brain. It involves applying low-intensity electrical currents to specific regions of the brain to modulate neural activity. This review paper aims to provide an overview of the comorbidities associated with ADHD and the differential diagnosis of the condition. It also explores the potential of tDCS as a treatment option for ADHD, including its mechanisms of action and efficacy in improving ADHD symptoms. The comorbidities discussed in this review include anxiety disorders, mood disorders, and substance use disorders. These comorbidities are frequently seen in individuals with ADHD and can complicate the diagnosis and treatment of the condition. The paper also highlights the importance of considering comorbidities when assessing ADHD, as well as the potential impact of these conditions on treatment outcomes. The differential diagnosis section of the paper explores conditions that can present with symptoms similar to ADHD, such as anxiety disorders, mood disorders, and learning disabilities. It emphasizes the need for a thorough assessment and differential diagnosis to identify ADHD and differentiate it from other conditions accurately. The final section of the paper discusses the potential of tDCS as a treatment option for ADHD. It examines the mechanisms of action of tDCS and its efficacy in improving ADHD symptoms, including attention, hyperactivity, and impulsivity. It also explores the potential for tDCS to improve comorbid conditions associated with ADHD. Overall, this review provides a comprehensive overview of comorbidities and differential diagnoses in ADHD and the potential of tDCS as a treatment option. The paper highlights the importance of a thorough assessment and personalized treatment plan for individuals with ADHD, particularly those with comorbidities.

The excitation of the visual system increases with increasing retinal illumination. At the same time, the sensitivity of the system decreases (light adaptation). Higher excitation automatically results in a lower sensitivity. This study investigates whether this parallelism between the excitation and the sensitivity also applies in the dynamic case, that is, during the transition to a higher excitation level after an increase in the retinal illuminance. For this purpose, the courses of the subjective and the electroretinographic threshold during the transitional phase after a step of the adaptation illumination was determined by means of a special light-stimulation apparatus. As a measure of the course of the excitation during this time, the response ERG on the adaptation step was recorded with a special amplifier. The threshold curve always has an overswing, which shows subjectively very strong differences. It can be concluded that the glare caused by a sudden increase in illuminance is subjectively very different. The comparison between the response ERG on the adaptation step and the course of the electroretinographic increment threshold during this time shows a broad agreement between the two courses. It can thus be assumed that the sensitivity of the visual system follows the course of the excitation also in the dynamic case. In addition, the investigation shows that the glare experienced after a step in the illuminance clearly shows great subjective differences.

Rising fuel costs, significant air pollution, and the need to mitigate the negative consequences of oil consumption have diminished the relevance of traditional vehicles. This shift encourages the adoption of safer, more efficient, and eco-friendly transportation alternatives, such as fuel cell, electric, and hybrid vehicles. Brushless direct current motors are gaining popularity due to their high efficiency, power factor, torque, and controllability. By 2030, Brushless Direct Current motors are expected to replace conventional motors as the standard for power transfer, especially in dynamic applications like automobiles, more electric aircraft. This study explores a control technique to improve real-time control of brushless direct current motors in electric vehicles It presents speed control of these system for electric vehicle applications and an overview of electric vehicle technologies. A model for the 120-degree mode was developed using electrical and mechanical equations in MATLAB/Simulink. Three scenarios were examined to assess the potential of controlling brushless direct current motors using constant and dynamic speed and torque. The actual value reached the reference value in the first two scenarios.

This paper reports the effect of silicon substrate orientation and aluminum nitride buffer layer deposited by molecular beam epitaxy on the growth of aluminum nitride thin films deposited by DC magnetron sputtering technique at low temperature. The structural analysis has revealed a strong (0001) fiber texture for both substrates Si (100) and (111) and a hetero-epitaxial growth on few nanometers AlN buffer layer grown by MBE on Si (111) substrate. SEM images and XRD characterization have shown an enhancement in AlN crystallinity thanks to AlN (MBE) buffer layer. Raman spectroscopy indicated that the AlN film was relaxed when it deposited on Si (111), in compression on Si (100) and under tension on AlN buffer layer grown by MBE/Si (111) substrates, respectively. The interface between Si (111) and AlN grown by MBE is abrupt and well defined; contrary to the interface between AlN deposited using PVD and AlN grown by MBE. Nevertheless, AlN hetero-epitaxial growth was obtained at low temperature (<250°C).

Adjustable frequency converters are widely used in modern automated asynchronous drives due to their high efficiency and high responsiveness control strategies. Control algorithms for frequency converters are divided into two main groups: constant frequency commutation and random frequency commutation. Research results on various commutation frequencies, conducted using Matlab/Simulink software, show that the use of random frequency commutation provides better efficiency by significantly reducing the amplitude of harmonic oscillations at different frequencies, with a reduction in switching losses in transistors. Currently, a converter with random frequency commutation is being researched and applied in the direct torque control system. The traditional direct control system, based on a two-level inverter, is widely used due to its simplicity and ease of implementation. However, this method results in the output current of the two-level converter, supplied to the motor stator, having many harmonic distortions, leading to strong torque fluctuations regardless of the rotation speed and ultimately causing additional losses in the stator windings and reducing the motor's lifespan. To enhance the efficiency of automated asynchronous drives, this article presents an algorithm for a direct control system based on a three-level NPC inverter using a PI speed regulator. The proposed algorithm's research is validated in the Matlab/Simulink environment. The research results show that in the absence of harmonic filtering, the stator current harmonic distortion coefficient is approximately 11%, and torque fluctuations are less than 5% of the resistive torque. The fluctuations between the two capacitors remain almost unchanged throughout the entire process.

Permanent magnet brushless DC motor (BLDCM) is usually controlled by six step commutation method, and flux-weakening method is used to make the motor run higher above the base speed. For now, it is considered that the weak magneto-electric angle range is 0-pi/3, and that of deep weakening is pi/3-pi/2. In the field- weakening control, the forward shift of commutation point will form inverter circulating current in the three-phase bridge of inverter and the stator winding of the motor. In this paper, the principle of inverter circulating current formed by inverter is analyzed. Through magnetic potential analysis and Simulink simulation, it is concluded that flux-weakening control will generate inverter circulating current in the inverter and motor stator winding. The inverter circulating current affects the magnetic potential of motor, and magnetic potential will move to the rotating direction of motor rotor. When the forward shift angle of inverter commutation point is 0-pi/6 electrical angle, the movement amplitude of current circulating current of inverter is less than pi/6, which plays the role of weakening magnetic field and driving effect; when the forward moving angle is pi/6-pi/3, the movement amplitude of inverter circulating current exceeds pi/6, which plays the role of magnetic weakening and braking. When the braking effect occurs, the reverse torque will appear, resulting in the decrease of motor torque and efficiency. Therefore, the range of weak magneto-electric angle should be between 0-pi/6.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

Aphasia is one of the most socially disabling post-stroke deficits. Although traditional therapies have been shown to induce adequate clinical improvement, aphasic symptoms often persist. Therefore, new rehabilitation techniques which act as a substitute or as an adjunct to traditional approaches are urgently needed. The present review provides an overview of the efficacy and safety of the most innovative approaches which have been proposed over the last twenty years. First, we examined the effectiveness of the pharmacological approach, principally used as an adjunct to language therapy, reporting the mechanism of action of each single drug for the recovery of aphasia. Results are conflicting but promising. Secondly, we discussed the application of Virtual Reality (VR) which has been proved to be useful since it potentiates the ecological validity of the language therapy by using virtual contexts which simulate real-life everyday contexts. Finally, we focused on the use of Transcranial Direct Current Stimulation (tDCS), both discussing its applications at the cortical level and highlighting a new perspective, which considers the possibility to extend the use of tDCS over the motor regions. Although the review revels an extraordinary variability among the different studies, substantial agreement has been reached on some general principles, such as the necessity to consider tDCS only as an adjunct to traditional language therapy.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

In the recent years, intelligent data-driven faultdiagnosis methods on gearboxes have been successfully developedand popularly applied in the industries. Currently, most ofthe machine learning techniques require that the training andtesting data are from the same distribution. However, thisassumption is difficult to be met in the real industries, sincethe gearbox operating conditions usually change in practice,which results in significant data distribution gap and diagnosticperformance deteriorations in applying the learned knowledgeon the new conditions. This paper proposes a deep learning-based domain adaptation method to address this issue. Theraw current signals are directly used as the model inputs fordiagnostics, which are easy to collect in the real industries andfacilitate practical applications. The maximum mean discrepancymetric is introduced to the deep neural network, the optimizationof which guarantees the extraction of generalized machineryhealth condition features across different operating conditions.The experiments on a real-world gearbox condition monitoringdataset validate the effectiveness of the proposed method, whichoffers a promising tool for cross-domain diagnosis in the realindustries.

Purpose: Dysarthria, a neurological injury of the motor component of the speech circuitry, is of common consequences of traumatic brain injury (TBI). Palilalia is a speech disorder characterized by involuntary repetition of words, phrases, or sentences. Based on the evidence supporting the effectiveness of transcranial direct current stimulation (tDCS) in some speech and language disorders, we hypothesized that using tDCS would enhances the effectiveness of speech therapy in a client with chronic dysarthria following TBI. Method: We applied the constructs of the “Be Clear” protocol, a relatively new approach in speech therapy in dysarthria, together with tDCS on a chronic subject who affected by dysarthria and palilalia after TBI. Since there was no research on the use of tDCS in such cases, regions of interest (ROIs) were identified based on deviant brain electrophysiological patterns in speech tasks and resting state compared with normal expected patterns using the Quantitative Electroencephalography (QEEG) analysis. Results: Measures of perceptual assessments of intelligibility, an important index in the assessment of dysarthria, ​​were superior to the primary protocol results immediately and 4 months after intervention. We did not find any factor other than the use of tDCS to justify this superiority. The percentage of repeated words, an index in palilalia assessment, had a remarkable improvement immediately after intervention but fell somewhat after 4 months. We justified this case with subcortical origins of palilalia. Conclusion: Our present case-based findings suggested that applying tDCS together with speech therapy may improve intelligibility in similar case profiles as compared to traditional speech therapy. To reconfirm the effectiveness of the above approach in cases with dysarthria following TBI, more investigation need to be pursued.

Background: In Transcranial Direct Current Stimulation (tDCS) the injected current gets distributed across the brain areas. The motive is to stimulate the target region-of-interest (ROI), while minimizing the current in non-target ROIs. For this purpose, determining the appropriate current-dose for an individual is difficult. Aim: To introduce Dose-Target-Determination-Index (DTDI) to quantify the focality of tDCS and examine the dose-focality relationship in three different populations. Method: Here, we extended our previous toolbox i-SATA to the MNI reference space. After a tDCS montage is simulated for a current-dose, the i-SATA(MNI) computes the average (over voxels) current density for every region in the brain. DTDI is the ratio of average current density at target ROI to the ROI with maximum value (peak region). Ideally target ROI should be the peak region, so DTDI shall range from 0 to 1. Higher the value, the better the dose. We estimated the variation of DTDI within and across individuals using T1-weighted brain images of 45 males and females distributed equally across three age groups- (a) Young adults (20 ≥ x ˂ 40 years), (b) Mid adults (40 ≥ x ˂ 60 years), and (c) Older adults (60 ≥ x ˂ 80 years). DTDI’s were evaluated for the frontal montage with electrodes at F3 and right supra-orbital for three current doses 1mA, 2mA, and 3mA with the target ROI at left middle frontal gyrus. Result: As the dose is incremented, DTDI may show (a) increase, (b) decrease, and (c) no change across the individuals. The focality decreases with age and the decline is stronger in males. Higher current dose at older age can enhance the focality of stimulation. Conclusion: DTDI provides information on which tDCS current dose will optimize the focality of stimulation. DTDI recommended dose should be prioritised based on the age (> 40 years) and sex (especially males) of an individual. The toolbox i-SATA(MNI) is freely available.

The existence of the hole on a plate affects the calculation of eddy current problems. Consequently, the accuracy for the prediction of the material properties decreases if the effect of the hole is not taken into account. In this paper, a novel analytical method based on the modified integration range is proposed which can address the presence of the hole. Due to the presence of the hole, the conventional Dodd-Deeds analytical solution cannot be used to calculate the inductance change. Therefore, a revised upper integration limit is introduced to replace the original limit -- ∞ when using the co-axially air-core electromagnetic sensor. With the presence of the hole, the magnitude of the received signal reduces, and the peak frequency feature changes. The analytical method is validated by measured and numerical simulation results. It is found that the upper limit is related to the radius of the open hole. With the new technique, the thickness of sample plates with holes can be estimated based on the peak frequency feature.

The eddy current loss should be optimized to be as less as possible for the stability of permanent magnet in high speed permanent magnet synchronous motor (HSPMSM) rotor and ensure the high efficiency and low temperature of the motor. This paper analyzes the eddy current distribution in rotor, with consideration of the conflict of the thickness of sleeve and diameter of the rotor, calculating the eddy current loss (ECL) and the thermal distribution via Separation of variables method for solving Maxwell's equations with analytical hieratical model of ECL constructed. The optimization result of ECL of the HSPMSM whose power and rated speed is 30kw 48000r/min can be got by multi-objective optimization method, combined weighting coefficient method and traversal algorithm based on chaotic local search particle swarm optimization (CLSPSO), utilizing ECL analytical model and other analytical constraints. Related experiment and measurement has been implemented with new approach of loss separation.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

Electrical energy demand increase does evolve rapidly due to several socioeconomic factors such as industrialization, population growth, urbanization and of course the evolution of modern technologies in this 4th industrial revolution era. Such rapid increase in energy demand introduces a huge challenge in power system. Such has paved way for network operators to seek for alternative energy resources other than the conventional fossil fuel system. Hence, the penetration of renewable energy into the electricity supply mix has evolved rapidly in the past three decades. However, the grid system has to be well planned ahead to accommodate such increase in energy demand in the long run. Transmission Network Expansion Planning (TNEP) is a well ordered and profitable expansion of power facilities that meets the expected electric energy demand with an allowable degree of reliability. This paper proposes a TNEP model that minimises the network reinforcements, operational costs and costs of renewable energy penetrations, while satisfying the increase in demand. The problem is formulated as a mixed integer linear programming (MILP) problem. The developed model has been tested in several IEEE test systems in multi-period scenarios. The paper also carried out a detailed derivation of the new non-negative variables in terms of the power flow magnitudes, the bus voltage phase angles and the lines’ phase angles for proper mixed integer variables’ decomposition techniques. Moreover, this paper tends to provide additional recommendation in terms of which particular year (within 20 years of planning period) can the network operators install new line(s), new corridor(s) and/or additional generation capacity to the respective existing power networks. Such is achieved by running incremental periods simulations from base year through the planning horizon. The results show the efficacy of the developed model in solving the TNEP problem with a reduced and acceptable computation time even for large power grid system.

The development and application of marine current energy are attracting more and more attention around the world. Due to the hardness of its working environment, it is important and difficult to study the fault diagnosis of a marine current generation system. In this paper, an underwater image is chosen as the fault-diagnosing signal, after different sensors are compared. This paper proposes a diagnosis method based on the sparse autoencoder (SA) and softmax regression (SR). The SA is used to extract the features and SR is used to classify them. Images are used to monitor whether the blade is attached by benthos and to determine its corresponding degree of attachment. Compared with other methods, the experiment results show that the proposed method can diagnose the blade attachment with higher accuracy.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

A computational methodology for the hydrodynamic analysis of horizontal axis marine current turbines is presented. The approach is based on a boundary integral equation method for inviscid flows originally developed for marine propellers and adapted here to describe the flow features that characterize hydrokinetic turbines. To this purpose, semi-analytical trailing wake and viscous-flow correction models are introduced. A validation study is performed by comparing hydrodynamic performance predictions with two experimental test cases and with results from other numerical models in the literature. The capability of the proposed methodology to correctly describe turbine thrust and power over a wide range of operating conditions is discussed. Viscosity effects associated to blade flow separation and stall are taken into account and predicted thrust and power are comparable with results of blade element methods that are largely used in the design of marine current turbines. The accuracy of numerical predictions tend to reduce in cases where turbine blades operate in off-design conditions.

There is a growing use of High Voltage Direct Current (HVDC) globally due to the many advantages of Direct Current (DC) transmission systems over Alternating Current (AC) transmission, including enabling transmission over long distances, higher transmission capacity and efficiency. Moreover, HVDC systems can be a great enabler in the transition to a low carbon electrical power system which is an important objective in today’s society. The objectives of the paper are to give a comprehensive overview of HVDC technology, its development, and present status, and to discuss its salient features, limitations and applications.

Three low band gap copolymers based on isoindigo acceptor units were designed and successfully synthesized by direct arylation polycondensation method. Two of them were benzodithiophene(BDT)-isoindigo copolymers (PBDTI-OD and PBDTI-DT) with 2-octlydodecyl(OD) and 2-decyltetradecyl (DT) substituted isoindigo units, respectively. Thiophene donor and DT-substituted isoindigo acceptor units were copolymerized to synthesize PTI-DT. The copolymers have broad absorption range that extends to over 760 nm with a band gap ~ .5 eV. The photophysical property studies showed the BDT based copolymers have non-polar ground states. Their emission exhibited the population of intramolecular charge transfer (ICT) state in polar solvents and tightly bound excitonic state in non-polar solvents due to self-aggregation. On the contrary, the emission from the thiophene based copolymers was only from the tightly bound excitonic state. The thermal decomposition temperature of the copolymers was above 380 oC. The X-ray diffraction pattern of the three copolymers showed a halo due pi-pi stacking. A second sharper peak was observed in the BDT-based copolymer with longer side chain on the isoindigo unit (PBDTI-DT) and the thiophene based copolymers with PTI-DT exhibiting a better structural order.

The Chile-Peru subpopulation (CPe) of the southern right whale (Eubalaena australis) is classified as critically endangered following intense whaling in past centuries. Due to their very low abundance, information on breeding and feeding grounds is also scarce. Unmanned aerial vehicles (UAVs) are increasingly applied in marine mammal research thanks to their low cost and relative ease of use. This case study documents a southern right whale nursing in Bahía Moreno (23ºS), Antofagasta, northern Chile, through high-resolution images taken by UAV of a lone adult in July 2019 and the same (photo-identified) whale with a neonate in August, confirming local parturition. Combined with earlier data we hypothesize that the Antofagasta Region may be a calving and nursing ground for the CPe subpopulation. Given the intense shipping traffic and fishing activities around the Mejillones Peninsula and Antofagasta port, priorly recommended marine spatial planning to help avoid net entanglements and vessel collisions of fin and humpback whales would also contribute to the conservation of the CPe stock of southern right whale.

The energy potential of long-period oscillations is estimated by comparing it with watercourse power. The relaxation time of long-period waves is chosen for the estimation time interval, during which their amplitude decreases e (Euler's number) times from the initial one. According to calculations, the amount of energy produced during this time by the watercourse is 9.35–18.71 million kW×h, while the amount of energy of long-period oscillations is 3–6 times less – 1.60–5.48 million kW×h. The components of the economic factor of using long-period waves and currents for electricity production are the predictability of their magnitudes and location of maxima, long-term availability, concentration.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

Background: Objectives. The objective of this study was to compare the efficacy of direct current stimulation (DCS) applied at the transcranial, suboccipital and spinal level on experimental sensory modalities and pain outcome measures in healthy subjects. The hypothesis of this study was that systematic analysis of the efficacy of DCS on modulating evoked thermal and mechanical pain modalities and mechanisms such as endogenous pain modulation in healthy individuals would reveal sensitive outcome measures help develop this technique for the control of chronic pain. Materials and Methods. Database searches were conducted up to December 2019 for randomized controlled trials that performed sham-controlled DCS of experimental sensory modalities and pain outcomes following transcranial, suboccipital and spinal locations in healthy participants. Standardized mean differences with 95% confidence intervals were calculated for sensory modalities, including random-effect metanalysis. Results: Thirty-one studies were included for analysis (647 participants). A significant decrease in pain intensity for active vs sham transcranial stimulation was identified for pain intensity (n=158; SMD=0.79; 95% CI=0.56 to 1.02), a significant increase in heat pain threshold (n=222; SMD=1.16; 95% CI=0.95 to 1.37), and a significant increase in cold pain threshold (n = 155; SMD = 0.77, 95% CI 0.53 to 1.01). No significant modulation of pressure pain threshold was identified with DCS and only a limited number of studies focused on experimental pain modulation following neuromodulation at the suboccipital or spinal level. Conclusions: These results show significant transcranial DCS neuromodulation of pain intensity and on thermal pain modalities. Future studies should focus on endogenous pain and sensory modality modulation with sham-controlled DCS applied at transcranial, suboccipital and spinal locations.

Building a new power plant to address the growing demand for power due to population concentration in the metropolitan area is one of the world's major concerns. However, since a large power plant can not be located around the city due to burden of economic cost, building power plant outside metropolitan and cities is necessary. Therefore, new power generation facilities are promoting policies to provide distributed generator(DG) with a small capacity relatively near the metropolitan. When the DG (photovoltaic, wind farm, etc.) is connected with the grid using medium voltage direct current (MVDC) system, voltage sourced converter(VSC) should supply reactive power to the grid, because of fault ride through(FRT) operation in grid fault. If the voltage drop is severe, the converter should be disconnected from the grid immediately without supplying the reactive power, resulting in a considerable economic loss. In general, superconducting fault current limiter(SFCL) is introduced as a measure to enhance FRT capability. In this paper, we use trigger type SFCL which protects superconducting element and reduces low voltage. On the other hand, the active power unbalance of the DC-link and the DC voltage rise due to the reactive power supply of the grid-side converter. The rise of the DC voltage causes the P (active power), Q (reactive power) control of the converter to deviate, causing malfunction and damage of the DC equipment. Therefore, the rise of the DC voltage must be prevented. In this paper, we consider the suppression the DC voltage rising caused by the FRT operation through the active power tracking control (APTC).

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

Transcranial direct current stimulation (tDCS) is acknowledged for its non-invasive modulation of neuronal activity in psychiatric disorders. However, its application in insomnia research yields varied outcomes depending on different tDCS types and patient conditions. Our primary objective is to elucidate its efficiency and uncover the underlying mechanisms in insomnia treatment. We hypothesized that anodal prefrontal cortex stimulation activates glutaminergic projections from the infralimbic cortex (IL) to ventrolateral preoptic area (VLPO) to promote sleep. After administering 0.06 mA of electrical currents for 8 minutes, our results indicate significant non-rapid eye movement (NREM) enhancement in naïve mice within the initial 3 hours post-stimulation, persisting up to 16-24 hours. In the insomnia group, tDCS enhanced NREM sleep bout numbers during acute stress response and improved NREM and REM sleep duration in subsequent acute insomnia. Sleep quality, assessed through NREM delta powers, remains unaffected. Interference of the IL-VLPO pathway, utilizing designer receptors exclusively activated by designer drugs (DREADDs) with the cre-DIO system, partially blocked tDCS's sleep improvement in stress-induced insomnia. This study elucidated that the activation of the IL-VLPO pathway mediates tDCS's effect on stress-induced insomnia. These findings support the understanding of tDCS effects on sleep disturbances, providing valuable insights for future research and clinical applications in sleep therapy.

This paper presents an approach to the vibration analysis of axially functionally graded non-prismatic Timoshenko beams (AFGNPTB) using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, shear moduli, and mass density) of axially functionally graded beams vary along the longitudinal axis. The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFGNPTB was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFGNPTB, considering the damping. The results obtained in this study showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

We extend the standard solid-state quantum mechanical Hamiltonian containing only Coulomb interactions between the charged particles by inclusion of the (transverse) current-current diamagnetic interaction starting form the non-relativistic QED restricted to the states without photons and neglecting the retardation in the photon propagator. This derivation is supplemented with a derivation of an analogous result along the non-rigorous old classical Darwin-Landau-Lifshitz argumentation within the physical Coulomb gauge.

The three-dimensional structure of Gulf of Mexico’s warm-core rings, detaching from the Loop Current, is investigated using satellite altimetry and a large set of ARGO float profiles. Reconstruction of the Loop Current rings (LCRs) vertical structure from sea surface height observations is made possible by the use of the gravest empirical modes method (GEM). The GEMs are transfer functions that associate a value of temperature and salinity for each variable pair {dynamic height;pressure}, and are computed by estimating an empirical relationship between dynamic height and the vertical thermohaline structure of the ocean. Between 1993 and 2021, 40 LCRs were detected in the altimetry and their three-dimensional thermohaline structure was reconstructed, as well as a number of dynamically relevant variables (geostrophic and cyclogeostrophic velocity, relative vorticity, potential vorticity, available potential energy and kinetic energy density etc.). The structure of a typical LCR was computed by fitting an analytical stream function to the LCRs dynamic height signature and reconstructing its vertical structure with the GEM. The total heat and salt contents and energy of each LCR were computed and their cumulative effect on the Gulf of Mexico’s heat, salt and energy balance is discussed. We show that LCRs have a dramatic impact on these balances and estimate that residual surface heat fluxes of -13 Wm−2 are necessary to compensate their heat input, while the fresh water outflow of the Mississippi river approximately compensates for their salt excess input. An average energy dissipation of O[10−10−10−9] Wkg−1 would be necessary to balance their energy input.

Pain is a multifaceted multisystem disorder that adversely affects neuro-psychological processes. This study compares the effectiveness of central-stimulation (tDCS) and peripheral-stimulation (TENS) in pain-inhibition during a cognitive-task in healthy volunteers and to observe potential neuro-cognitive improvements. Healthy eighty volunteers went through a complete experimental protocol comprising pain-induction (CPT), administration of tDCS/TENS, EEG-data acquisition, and cognitive assessments. The protocol for this study is categorized into 04-groups: G1(Control), G2(TENS), G3(Anodal-tDCS), and G4(Cathodal-tDCS). Paired t-tests (p

Transcranial direct current stimulation (tDCS) over the left Inferior Frontal Gyrus (IFG) was found to improve apraxia of speech (AOS) in post-stroke aphasia, speech fluency in adults who stutter, naming and spelling in primary progressive (PPA). This paper aims to determine whether tDCS over the left IFG coupled with AOS therapy improves speech fluency in patients with PPA more than sham. Eight patients with non-fluent PPA with AOS symptoms received either active or sham tDCS, along with speech therapy for 15 weekday sessions. Speech therapy consisted of repetition of increasing syllable-length words. Evaluations took place before, immediately after, and two months post-intervention. Words were segmented into vowels and consonants and the duration of each vowel and consonant was measured. Segmental duration was significantly shorter after tDCS than sham for both consonants and vowels. tDCS gains generalized to untrained words. The effects of tDCS sustained over two months post-treatment in trained words. Taken together, these results demonstrate that the tDCS over the left IFG facilitates speech production by reducing segmental duration. The results provide preliminary evidence that tDCS can maximize efficacy of speech therapy in non-fluent PPA with AOS.

This paper presents an approach to the vibration analysis of axially functionally graded (AFG) non-prismatic Euler-Bernoulli beams using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, and mass density) of AFG beams vary along the longitudinal axis. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFG non-prismatic Euler-Bernoulli beams was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFG non-prismatic Euler-Bernoulli beams, considering the damping. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

Cognitive impairment is a condition which affects aging patient populations and is becoming more prevalent as the geriatric population expands. It is categorized by the extent of cognitive decline, memory loss, functional abilities, and the capability to perform daily tasks. Based on the degree of impairment, it is classified as mild cognitive impairment or dementia. Considering the debilitating nature of cognitive decline and its impact on quality of life, prevention is key. In addition, given the gradual progression of the underlying causes of cognitive decline, early diagnosis and appropriate management has the potential to offer clinical advantages and better patient outcomes. Management options discussed vary from pharmaceutical regimens to neurosurgical interventions, with differing outcomes based on etiology of cognitive impairment.

This article investigated the Automatic Generation Control(AGC) of multi-area multi-source interconnected systems with hydropower plants, thermal power plants, and wind energy. Adaptive Neuro-fuzzy controller integrated with the cascaded proportional-integral-derivative with filter (PIDF-PIDF) is a new cascaded controller (ANF-PIDF-PIDF) that has been presented as a secondary controller for applied hybrid power systems. The recent Skill Optimization Algorithm (SOA) is employed to optimize PIDF- PIDF controller parameter gains and the Adaptive Neuro-Fuzzy controller's inputs and output scaling factors. SOA is used to update the controller parameters with integral square error (ISE) employed as the objective function. A 1% step load disturbance was considered simultaneously in all three areas. The controller's performance is evaluated and compared with and without considering the effects of wind energy sources and non-linearity for ANF-PIDF-PIDF, PIDF-PIDF, and PIDF and it was determined that the ANF-PIDF-PIDF was the most efficient. The dynamic system performance is also compared with parallel high voltage direct current (HVDC) tie-lines. The investigation clearly shows that incorporating HVDC tie-line with multi-area, multi-source provides better dynamic performance in maximum amplitude, oscillation, and settling time. Additionally, sensitivity analysis is done and the optimum controller gains does not need to be reset to uncertain values in system loading conditions. All simulation results were evaluated using MATLAB 2016b.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

Current sources play an essential role in tissue excitation used in bioelectrical impedance spectroscopy. Most investigations use Howland current sources that, despite their practicality and simplified implementation, have operating frequency limitations and dependence on the load impedance due to theirs narrow output impedance, specially at higher frequencies. The objective of this work is to propose model for a robust current-controlled sinusoidal oscillator. The oscillator is based on fully analog electronics, which enables controlling oscillation phase and amplitude by using a voltage reference. The mathematical model is based on Pyragas control application to the classical harmonic oscillator. From the modelling process, it was build an oscillator topology based on second-generation current carriers and on transconductance amplifiers. The reference signal (Fsync) was a sinusoidal voltage source having a frequency of 1MHz and an amplitude of 1Vpp. The oscillator output current synchronized the oscillations’ phase and amplitude with Fsync, regardless of their magnitude before the control signal acted in the circuit at t≈13.5μs. SPICE simulations using ideal components have confirmed the successful operation of the proposed oscillator. This type of oscillator can be implemented in SOIC, then allowing oscillation control interface with logic circuits.

The measurement range of a conventional current sensor is narrow because it is used with signals relative to the rated values of the measurement range from a voltage-type device. Consequently, multiple current sensors must be used in accordance with the measurement range. To address this problem, this paper proposes a new current sensor with a clamp-shaped part for low current measurement and a simple straight structure for high current measurement. The output signals of the proposed current sensor are amplified with a Hall element using the magnetic force of a rectangular air gap inside the clamp. To verify the characteristics of the proposed current sensor, a current was applied to an external load, and the value determined by the current sensor noted. Then, electromagnetic field analysis was performed through current sensor modeling and the results obtained compared to the actual sensor results. The proposed sensor had a 1% linearity in the output signals and exhibited dynamic characteristics over a wide current range.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

In this paper we give the new formulas for calculating the self-inductance for the circular coils of the rectangular cross sections with the radial and the azimuthal current densities. These formulas are given by the single integration of the elementary functions which are integrable on the interval of the integration. From these new expressions we can obtain the special cases for the self-inductance of the thin disk pancake and the thin wall solenoid that confirm the validity of this approach. For the asymptotic cases, the new formula for the self-inductance of the thin wall solenoid is obtained for the first time in the literature. In this paper we do not use special functions such as the elliptical integrals of the first, second and third kind, Struve, and Bessel functions because that is very tedious work. The results of this work are compared with already different known methods and all results are in the excellent agreement. This is way we consider this approach as the novelty because of its simplicity in the self -inductance calculation of the previously mentioned configurations.

In this paper, we present a preliminary study and conceptual idea concerning 3D printing water-sensitive glass by exemplifying with a borosilicate glass with high alkali and alkaline oxide contents using direct ink writing. The investigated material was prepared in the form of a glass frit, which was further ground in order to obtain a fine powder of desired particle size distribution. In a following step, inks were prepared by mixing the fine glass powder with Pluoronic F-127 hydrogel. The acquired pastes were rheologically characterized and printed using a Robocasting device. DSC experiments were performed for base materials and the obtained green bodies. After sintering, SEM and XRD analyses were carried out in order to examine microstructure and the eventual presence of crystalline phase inclusions. Results confirmed that obtained inks exhibit stable rheological properties despite the propensity of glass to undergo hydrolysis and could be adjusted to desirable values for 3D printing. No additional phase was observed, supporting the suitability of the designed technology for the production of water sensitive glass inks. SEM micrographs of the sintered samples revealed the presence of closed porosity, which may be the main reason of light scattering.

It is widespread to examine and explain the functioning of the standard “Current Doubler Rectifier” as strictly symmetrical according to the electrical current through the two inductances. The present work challenges this consideration and proposes a new version of the electrical circuit daigram where the current symmetry is improved. The proposed circuit is called “Improved Current Doubler Rectifier”.

Stray currents can cause very rapid degradation and material loss at the points where the current leaves the metal and enters the electrolyte. Nowadays, many resources are invested in the protection of jeopardized structures, such as buried pipelines, from stray current corrosion. This paper describes the measures that need to be considered in the design and construction of track structures to ensure high rail-to-ground resistance and consequently reduce stray currents. The main conclusions from existing guidelines and standards for reducing and controlling stray currents that are applied by various track operators are presented in the paper. Rail-to-ground resistance in different types of tracks structures and rail fastening systems is analysed and optimal type of the track and type of the fastening system is defined. The grounding schemes used on the tracks and their influence on stray current values are described, as well as the influence of traction power substation and rail cross bonding on stray current. Since it is not necessary to apply all the measures described to the same track structure, the paper gives recommendations on which measures to apply when building tracks with continuously fastened rails and which to apply when building tracks with discretely supported and fastened rails.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.

The paper presents the methods of assessing the technical condition of varistor surge arresters used in laboratory tests and in operation - performed without disconnecting the arresters from the network. The analysis of diagnostic methods was supplemented with the results of measurements of the leakage current of arresters coming directly from production and used in the power industry. Among the available methods of evaluating the technical condition of arresters, mainly indicator solutions (temperature, operation counter) and using the measurement of selected parameters of the leakage current are used. In the latter, the method of determining the resistive component of the leakage current, determined on the basis of the analysis of voltage and current waveforms, or only the arrester current, has become widespread. In this type of measurements, current clamps are used in operation, and additionally in voltage measurements from voltage transformers, where you have to take into account the fundamental, additional sources of errors discussed in the article. These errors and dispersion resulting from the production technology may fundamentally hinder the proper assessment of the technical condition, hence it is so important to properly recognize the listed basic sources of measurement uncertainty. In addition, the analysis should take into account three factors related to external conditions - temperature, voltage applied to the arrester and the content of higher harmonics in the supply voltage for which appropriate methods have been provided to determine the active component of the leakage current for reference conditions.

We show that the implementation of the 1/c² transverse current-current interaction between electrons into the standard self-consistent electron BCS model in bulk under thermal equilibrium ensures in the stable superconductive phase the full compensation of a constant external magnetic field by the internal magnetic field created by the electrons i.e. one has an ideal diamagnet. However, no proof of the phenomenological London equation emerges within the bulk approach.

A thorough study on the distribution of defect-related active energy levels has been performed on nanocrystalline TiO₂. Films have been deposited on thick-alumina printed circuit boards equipped with electrical contacts, heater and temperature sensors, to carry out a detailed thermally stimulated currents analysis on a wide temperature range (5-630K), in view to evidence contributions from shallow to deep energy levels within the gap. Data have been processed by numerically modelling electrical transport. The model considers both free and hopping contribution to conduction, a density of states characterized by an exponential tail of localized states below the conduction band and the convolution of standard TSC emissions with gaussian distributions to take into account the variability in energy due to local perturbations in the highly disordered network. Results show that in the low temperature range, up to 200K, hopping within the exponential band tail represents the main contribution to electrical conduction. Above room temperature, electrical conduction is dominated by free carriers contribution and by emissions from deep energy levels, with a defect density ranging within 10¹⁴ – 10¹⁸cm^-3, associated to physio- and chemi-sorbed water vapour,OH groups and to vacancy-oxygen defects.

Apraxia of speech is a persistent speech motor disorder that affects speech intelligibility. Studies on speech motor disorders with transcranial Direct Current Stimulation (tDCS) have been mostly directed to post-stroke aphasia. Only a few tDCS studies have focused on apraxia of speech or childhood apraxia of speech (CAS), and no study has investigated individuals with CAS and people with trisomy 21 (T21, Down Syndrome). This study examined the effects of tDCS combined with a motor learning task in developmental apraxia of speech co-existing with T21 (ReBEC RBR-5435x9). The accuracy of speech sound production of nonsense words (NSWs) during Rapid Syllable Transition Training (ReST) under 10 sessions of anodal tDCS (1.5 mA, 25 cm) over the Broca’s area with cathode over the contralateral region was compared to 10 sessions of sham-tDCS and 4 control sessions in a 20-year-old male individual with T21 presenting moderate-severe childhood apraxia of speech (CAS). The accuracy for NSWs production progressively improved (gain 40%) under tDCS only (sham-tDCS and control sessions showed <20% gain). A decrease in speech severity from moderate-severe to mild-moderate indicated transfer effects in speech production. The speech accuracy under tDCS was correlated with Wernicke’s area activation (P3 current source density), which in turn, was correlated with the activation of the left supramarginal gyrus and the Sylvian Parietal Temporal Junction. Repetitive bihemispheric tDCS paired with ReST may have facilitated the speech sound acquisition in a young adult with T21 and CAS, possibly by recruiting brain regions required for the phonological working memory.

Multi-parameter families of Lax pairs for the modified Korteweg-de Vries (mKdV) equation are defined by applying a direct method developed in the present study. The gauge transformations converting the defined Lax pairs to some simpler forms and reducing the variety of the Lax pairs this way are found. The direct method and its possible applications to other types of evolution equations are discussed.

Atrial fibrillation (AF) is an increasingly recognized comorbidity in patients with cancer. Indeed, cancer patients have a significantly higher incidence of AF than that observed in the general population. A reciprocal relationship between these two diseases has been observed, as much as some assume AF as a marker for occult cancer screening, especially in older adults. The pathophysiological mechanisms are many and varied, including the underlying pro-inflammatory state, specific treatments (chemo and radiotherapy) and surgery. The therapeutic management of patients with cancer and AF involves the same rhythm and frequency control strategies as the general population; however, the numerous interactions with chemotherapeutics, which lead to a significant increase in side effects, as well as the extreme fragility of the patient should be considered. Anticoagulant therapy is also a complex challenge to address, as bleeding and stroke risk scores have not been fully assessed in this subpopulation. Furthermore, in large studies establishing the efficacy of direct oral anticoagulants (DOACs), cancer patients have been underrepresented. In this review, we elaborate on mechanisms linking AF to cancer patients with a particular focus on therapeutic challenges in this population.

The effects of 0.4wt.% Sc addition on a typical Al-Si10-Mg alloy were systematically investigated in the present research. Samples with and without Sc produced refined dendritic arranged microstructures with sensitivity to the aging treatment after solidification, particularly in the case of the alloy without Sc. After being exposed to 300°C for 90 minutes, the dendritic spacing nearly doubled in the Al-10wt.%Si-0.45wt.%Mg samples. The rapidly solidified microstructures were constituted by the -Al dendritic phase surrounded by eutectic phases/intermetallics such as Si, Mg2Si and Al3Sc (in the case of the alloy containing Sc). 255°C and 300°C were deemed most appropriate temperatures for aging treatments, with four exposure times of up to 120 minutes tested for each alloy. The heat treatments allowed the Vickers hardness profiles to be plotted and compared. Moreover, in order to detect both Sc- and Mg- precipitates after aging, specific samples have been prepared for either SEM or TEM analyses. At first, the results pointed to a strong precipitate-related hardening effect formed as a result of the Sc addition to the alloy. All samples containing Sc showed a higher hardness value when compared to their respective treated samples without Sc. Secondly, when comparing the Al-10Si-Mg-Sc alloy samples among themselves after being treated at different conditions, high temperatures and excessive treatment times can become detrimental to the hardness. This was due to the growth of larger Sc-bearing precipitates of approximately 1 µm in size under such conditions, having less pronounced hardening effect. The best condition (255°C for 60 min) for as centrifuged samples in Cu-mold produced very fine dispersion of Mg- and Sc- intermetallics (~200 nm in size) with a peak hardness of 110 HV.

A hybrid smart process and material design system for nanoimprinting is proposed, which combines with a learning system based on experimental and numerical simulation results. Instead of carrying out extensive learning experiments for various condition, the simulation learning results are partially complimented where the results can be theoretically predicted by numerical simulation. In other word, the lacking data in experimental learning are complimented by simulation-based learning results. Therefore, the prediction of nanoimprint results under various conditions without experimental learning could be realized even for unknown materials. In this study, material and process design for a low-temperature nanoimprint process using glycerol-containing polyvinyl alcohol are demonstrated. Experimental results under limited conditions are learned to investigate optimum Glycerol concentrations and process temperatures. On the other hand, simulation-based learning is used to predict the dependence on press pressure and shape parameters. The prediction results for unknown Glycerol concentrations agreed well with the follow-up experiments.

This paper aims to research whether there is link between FDI inflows and Economic growth in the Republic of Seychelles Island. The ordinary least square results obtained shows that in the impact of FDI inflows on economic growth is low. Small Island Developing States attracts less FDI inflow because they are limited to few resources that attracts overseas firms which results in retarded development. The research lighted that impact of foreign direct investment on host countries does not only depend on the quality and quantity of the FDI inflows but some other variables such as the internal policies and the management skills, market structures, economic trends among others.

The aim of this paper is to present a comprehensive overview of the main aims and scopes in screening of botanicals, a task which thin-layer chromatography (TLC) is on an everyday basis confronted with and engaged in. Stunning omnipresence of this modest analytical technique (both in its standard format (TLC) and the high-performance one (HPTLC), either hyphenated or not) for many analysts might at a first glance appear chaotic and random, with an auxiliary rather than leading role in research, and not capable of issuing meaningful final statements. Based on these reflections, our purpose is not to present a general review paper on TLC in screening of botanicals, but a blueprint rather (illustrated with a selection of practical examples), which highlights a sovereign and important role of TLC in accomplishing the following analytical tasks: (i) solving puzzles related to chemotaxonomy of plants, (ii) screening a wide spectrum of biological properties of plants, (iii) providing quality control of herbal medicines and alimentary and cosmetic products of biological origin, and (iv) tracing psychoactive plants under forensic surveillance.

With the unceasing advancement in wide-bandgap (WBG) semiconductor technology, the minimal reverse-recovery charge Qrr and other more powerful natures of WBG transistors enable totem-pole bridgeless PFC to become a dominant solution for energy storage systems (ESS). This paper focuses on design and implementation of a control structure for a totem-pole boost PFC with newfangled enhancement-mode Gallium Nitride (eGaN) FETs, not only to simplify the control implementation, but also to achieve high power quality and efficiency. The converter is designed to convert a 90-264-VAC input to a 385-VDC output for a 2.6-kW output power. Lastly, to validate the methodology, an experimental prototype is characterized and fabricated. The uttermost efficiency at 230 VAC attains 99.14%. The lowest total harmonic distortion in the current (ITHD) at high line condition (230 V) reaches 1.52% while the power factor gains 0.9985.

This paper presents an approach to the Kirchhoff-Love plate theory (KLPT) using the finite difference method (FDM). The KLPT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally in the case of KLPT, the finite difference approximations are derived based on the fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection surface. The FOPH is made for the fourth and third derivative of the deflection surface while the SOPH is made for its second and first derivative; this leads to a 13-point stencil for the governing equation. In addition, the boundary conditions and not the governing equations are applied at the plate edges. In this paper, the FOPH was made for all of the derivatives of the deflection surface; this led to a 25-point stencil for the governing equation. Furthermore, additional nodes were introduced at plate edges and at positions of discontinuity (continuous supports/hinges, incorporated beams, stiffeners, brutal change of stiffness, etc.), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at the plate edges and to satisfy the boundary and continuity conditions. First-order analysis, second-order analysis, buckling analysis, and vibration analysis of plates were conducted with this model. Moreover, plates of varying thickness and plates with stiffeners were analyzed. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. In first-order, second-order, buckling, and vibration analyses of rectangular plates, the results obtained in this paper were in good agreement with those of well-established methods, and the accuracy was increased through a grid refinement.

Here we present calculation of the critical current of DC SQUID based on the Josephson junction on multi-band superconductor with frustration effect. It is shown that the changing of the critical current of DC SQUID with small geometrical inductance is determined by the ratio of supercurrent amplitude in different channels and the external magnetic field. In the a case of DC SQUID with high inductance frustration effects can be ignored.

This study introduces an alternative to the existing methods for measuring ocean currents based on a recently developed technology. The SailBuoy is an unmanned surface vehicle powered by wind and solar panels that can navigate autonomously to predefined way-points and record velocity profiles using an integrated downward-looking Acoustic Doppler Profiler (ADCP). Data, collected on two validation campaigns, shows a satisfactory correlation between the SailBuoy current records and traditional observation techniques such as bottom mounted and moored current profilers and moored single-point current meter. While the highest correlations were found in tidal signals, strong current, and calm weather conditions, low current speeds and varying high wave and wind conditions reduced correlation considerably. Filtering out some events with high sea surface roughness associated with high wind and wave conditions may increase the SailBuoy ADCP listening quality and lead to better correlations. Not yet resolved is a systematic offset between the measurements obtained by the SailBuoy and the reference instruments of ± 0.03 m/s. Possible reasons are discussed to be the differences between instruments (various products) as well as changes in background noise levels due to environmental conditions.

This article presents the development of the theoretical background and the design of an electronic device for monitoring the condition of a gapless Metal Oxide Surge Arrester (MOSA). The device is intended to be used online. Due to the inaccessibility and possible remote location of most surge arresters, it is equipped with a communication system, allowing the device to convey the measurement of the surge arrester characteristics under any conditions. By gathering measurements of the surge arrester’s resistive component of leakage current, it is possible to determine the condition of the MOSA. After interpreting the results, these can be sent via a data transfer unit to a server, which, in turn, sends it onward to the authorised personnel through the surge arrester control centre.

The high-power Asymmetric half-bridge Converter (AHBC) LED constant current driver controlled by digital current mode is a fourth-order system. Static operating point, parasitic resistance, load characteristics, sampling effect, modulation mode and loop delay will have great influence on its dynamic performance. In this paper, the small-signal pulse transfer function of the driver is established by the discrete-time modeling method for the two operating points corresponding to the three modulation modes of the trailing edge, leading edge and double edge. And, the effects of parasitic parameters, delay effect, sampling effect and load effect are fully considered in modeling. For a large number of complex exponential matrix operations, the first order Taylor formula is used for approximate calculation after the coefficient matrix is obtained by substituting the data. Then, Matlab software is used to compare and analyze the discrete-time model and the discrete-average model. The results show that the proposed discrete-time model can more accurately characterize the resonant peak and high-frequency dynamic characteristics, and is very suitable for the design of high frequency digital controller.

Normally, the Nernst voltage calculated from the concentration of the reaction gas in the flow channel is considered to be the ideal voltage (reversible voltage) of the oxyhydrogen fuel cell, but actually it will cause a concentration gradient when the reaction gas flows from the flow channel through the gas diffusion layer to the catalyst layer. The Nernst voltage loss in fuel cells in most of the current literature is thought to be due to the difference in concentration of reaction gas in the flow channel and concentration of reaction gas on the catalyst layer at the time when the high net current density is generated. Based on the Butler-Volmer equation in oxyhydrogen fuel cell, this paper demonstrates that the Nernst voltage loss is caused by the concentration difference of reaction gas in flow channel and on the catalytic layer at the time when equilibrium potential (Galvanic potential) of each electrode is generated.

Societies around the world face serious energy problems related to the consumption of fossil fuels and the emission of dangerous radiation. To solve these problems, a new superconductor exhibiting a critical temperature higher than room temperature has been pursued but not achieved. This paper proposes a new energy generation system based on a circuit approach. Secondary to this process, a new type of superconductivity without refrigeration is demonstrated. In our previous paper [1], this system was proposed, but it did not describe the underlying theory in detail and did not mention an actual method to generate energy from the system. The present paper describes the theory of the existence of divergent current density and new superconductivity with no refrigeration. Moreover, the present paper proposes a method for extracting energy from the system by employing a voltage-controlled current source (i.e., a voltage–current converting method).The principle of the system is based on a circuit of two loops and independent current sources. First, the two electric loops are prepared, each with 4 diodes, where the diodes are oriented in the same direction within each loop, but their direction is opposite from loop to loop; four independent current sources connect the loops. In this circuit system, current is added iteratively as it flows along the loop according to Kirchhoff’s circuit law. As a result, a large current and electric potential are present along the loop. To confirm that this system works properly, it is necessary to demonstrate the presence of divergent currents in the transient state, and to do this, the present paper employs the Dirac equation and Lorentz conservation. Electric circuit software is employed to demonstrate that the presented method generates energy actually from our system.Our results confirm the presence of divergent current at a connected point of an independent current source in the transient state. Moreover, in the steady state, the theory demonstrates the Meissner effect (i.e., a London equation) and a new type of macroscopic wave function and condensation. For an initial small input current of 0.1 μA, the simulation reveals a large generating current of 7 kA and electric power of 10¹¹ W, which is much larger than unit of power from an average thermal power station; moreover, the system presents with superconducting electrical transport conditions.The present study is significant because it demonstrates theoretically the existence of divergent current density and a new type of superconductivity requiring no refrigeration. Secondly, the simulations show the generation of a large energy density that can be obtained in a small laboratory room with minimal cost.

A single water pollution by dyes is a huge environmental problem; there is a necessity to produce new decolorization methods that are effective, cost-attractive, and suitable in industrial use. Magnetic chitosan polymers offer the advantage of easy separation from the dye solution. In this work, a Chitosan-Fe polymer was synthesized, characterized, and tested for removal of the azo dye Direct Red 83:1 from water. The polymer was characterized in terms of surface morphology (SEM), elemental analysis (EA), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), infrared spectrophotometry (IR), X-ray powder diffraction (XRD) and density functional theory (DFT). The reported results hint that 1 g and pH 7.0 were the best conditions to carry out both kinetic and isotherm models. To understand the adsorption behavior of Direct Red 83:1 onto the polymers, adsorption rate and maximum adsorption capacity were calculated using kinetic tests and isotherm curves respectively. The kinetic data and mechanism of the adsorption process were analyzed by three models and the equilibrium data by three adsorption isotherms. The results indicated that the adsorption process follows a pseudo-second-order kinetics (R2= 0.999) and fits the Temkin isotherm (R2= 0.946), indicating that the adsorption occurred on heterogeneous surfaces. The newly synthesized Chitosan-Fe polymer exhibited good adsorption properties and easy separation of cleaned water.

This 16-month study aimed to evaluate the extended effects of administering direct-fed microbials (DFM) on milk yield and components in 150 dairy cows. The cows were randomly divided into two groups: control (n=75) and DFM (n=75) based on parity and days in milk. Throughout the study, the two groups of cows were housed separately in a free stall yard, and each group had their own feeding area. The DFM group received 10 ml/cow of the Lacticaseibacillus- and Lentilactobacillus-based DFM via top dressing of the feed during lactation and drying off. Milk yield and liveweight were recorded daily. Milk samples were collected every two months for milk components analysis. Both groups produced less milk in the second production season due to adverse weather conditions. DFM cows gained more liveweight across the study (19.40 kg, 95% CI 0.44; 38.30) compared to controls. In the second season, DFM cows lost weight at a slower rate (-6.06, 95% CI -10.49; -1.61) during the postpartum period and produced more milk (0.39 L/d 95% CI 0.10; 0.89). Over a full lactation, DFM cows yielded at least 258L (95% CI 252L; 265L) more milk than controls. No significant differences were found in fat yield, protein yield, or somatic cell counts. The study suggests that prolonged DFM administration positively impacted milk production, but further research is needed to understand the underlying mechanism.

Laser patterning of implant materials for bone tissue engineering purposes has shown to be a promising technique to control cell properties such as adhesion or differentiation, resulting in an enhanced osteointegration. However, the perspective of patterning the bone tissue side interface to generate microstructure effects has never been investigated. In the present study, three different laser-generated patterns were machined on the bone surface with the aim to identify the best surface morphology compatible with osteogenic-related cells recolonization. The laser patterned bone tissue was characterized by electron scanning microscopy and confocal microscopy in order to obtain a comprehensive picture of the bone surface morphology. Cortical bone patterning impact upon cell compatibility and cytoskeleton rearrangement to the patterned surfaces was performed with Stromal Cells from Apical Papilla (SCAPs). Results indicated that laser machining had no detrimental effect upon consecutively seeded cells metabolism. Orientation assays revealed that surface patterning characterized by larger hatch distances was correlated with a higher cell cytoskeletal conformation to the laser-machined patterns. For the first time, to our knowledge, bone is considered and assessed here as a potentially engineered-improvable biological interface. Further studies shall focus on in vivo implications of this direct patterning.

Fostering innovation is considered one of the key policy priorities in most governments' agendas in developing countries, and foreign direct investment (FDI) is considered a principal resource for financing sustainable development, corresponding to 17 sustainable development goals (SDGs). This study analyzes the extent to which inward FDI affects innovation (proxied with patent applications) in Sri Lanka using secondary data from 1990 to 2019. We used the Autoregressive Distributed Lag (ARDL) cointegration procedure to examine the long-run relationships between variables. As per the study results, the coefficient of inward FDI is a negative sign while the coefficients of per capita gross domestic product (GDP) and high technology exports (HEX) show positive signs 2.142 and 0.414, respectively, and statistically significant in the long run. It is demonstrated that per capita GDP and high technology exports are an important variable in explaining technological innovation, and inward FDI and education expenditure (EDU) did not contribute towards widening technological innovation in Sri Lanka. Shaping the future of FDI in Sri Lanka is essential to foster innovation capability.

The paper deals with the problems of direct kinematics related to a 2T6R robot, the direct kinematics of the plane mechanism of the robot. The direct kinematics of this proposed new robot help to study the movement, including the dynamic one, to determine the forces in the mechanism and to model the possible trajectories of the final effector point, thus determining the robot's working space and some of its multiple possible uses. Two totally different methods were used to verify the calculation relations, the results obtained by both methods being practically identical. The first method used is an original trigonometric method, and the second is an original geometrically analytical method.

Power generation systems based on renewable energy sources are finding ever-widening applications and many researchers work on this problem. Many papers address the problem of transformerless structures, but few of them are aimed at conducting research on structures with multilevel converter topologies. In this paper a grid-tied transformerless PV-generation system based on a multilevel converter is discussed. There are common-mode leakage currents which act as a parasitic factor. It is also known that common-mode voltage is the main cause of the common-mode leakage current in grid-tied PV-generation systems. This paper considers the space vector pulse-width modulation (PWM) technique which is used to suppress or reduce common-mode leakage current. The proposed engineering solutions for a generation system based on the multilevel converter controlled with a pulse-width modulation technique are verified by experiment.

As we all know, contemporary electromagnetic theory is based on the macroscopic electromagnetic theory established by the 19th century. Because of the lack of microscopic cognition in that era, various electromagnetic phenomena could only be explained and described at the macro level, and their origins could not be explained at the micro level. And because of the microscopic understanding of atomic physics in the 20th century, new progress has been made. Considering that it is now the 21st century, this paper attempts to establish a new theory of microscopic interpretation of classical electromagnetic theory based on the new cognition of atomic physics in the 20th century. Starting from the general assumption, the current will be interpreted as the momentum flow produced by the directed collision between electrons; the charge will be interpreted as a form of expression of electron motion; the voltage is interpreted as the potential difference (energy level difference) of the electron orbit. In the end, this paper successfully developed a new microscopic electromagnetic theory by introducing microscopic atomic physics and rigid body mechanics models to Maxwell's macroscopic electromagnetic theory.

A power conservative Thevenin-Norton and Norton-Thevenin transformations are proposed in this letter. The transformations introduce a voltage and a current generators for which parameters depend on the loading impedance value.

This review focuses on the evidence for neurotherapeutics for Attention Deficit Hyperactivity Disorder (ADHD). EEG-Neurofeedback has been tested for about 45 years with latest meta-analyses of randomised controlled trials (RCT) showing small/medium effects compared to non-active controls only. Three small studies piloted neurofeedback of frontal activations in ADHD using functional magnetic resonance imaging or near-infrared spectroscopy, finding no superior effects over control conditions. Brain stimulation has been applied to ADHD using mostly repetitive transcranial magnetic and direct current stimulation (rTMS/tDCS). rTMS has shown mostly negative findings on improving cognition or symptoms. Meta-analyses of tDCS studies targeting mostly dorsolateral prefrontal cortex show small effects on cognitive improvements with only two out of three studies showing clinical improvements. Trigeminal nerve stimulation has shown to improve ADHD symptoms with medium effect in one RCT. Modern neurotherapeutics are attractive due to their relative safety and potential neuroplastic effects. However, they need to be thoroughly tested for clinical and cognitive efficacy across settings and beyond core symptoms and for their potential for individualised treatment.

This paper reports a new control strategy to improve sharing of unbalanced currents in islanded LV microgrids. This technique provides fast and effective sharing of positive-, negative- and zero-sequence currents, and is the first example of zero-sequence current sharing in the literature. The controllers are designed in the stationary frame. The control structure consists of four loops; 1)~the current controller; 2)~the voltage controller; 3)~the droop controller and the 4)~negative and zero sequence current controllers. The output current is considered unknown for the controller and is added to the control system as a disturbance. The proposed controller features a high gain in fundamental and harmonic frequencies, hence a good voltage quality is obtained in the presence of unbalanced and nonlinear loads. To this aim, a proportional-resonant (PR) controller is adopted as the current controller. By using a multi-resonant controller as current controller, a unified control structure is obtained which is suitable for both grid-connected and islanded modes. The voltage controller is designed using a resonant controller so that the voltage can have low VUF and THD in the presence of unbalanced and nonlinear loads. Furthermore, in this paper droop method is applied to the control structure to share real and reactive powers. Simulation studies show that the conventional droop method cannot share the oscillatory part of the output power that is due to the presence of unbalanced loads in the microgrid. This paper relies on using zero and negative sequence virtual impedance controller to share the oscillatory part of output power. By using zero-sequence virtual impedance controller (ZSVIC) and negative-sequence virtual impedance controller (NSVIC), the zero and negative sequence currents in the microgrid are controlled and shared effectively. By compensating zero- and negative-sequence currents locally, the flow of these currents in the microgrid is minimized, and the overall power quality of the islanded LV microgrid is improved.

Respiratory viral infections (RVI) are common reasons for healthcare consultations. The inpatient management of RVI consumes significant resources. From 2009-2014, we assessed the costs of RVI management in 4776 hospitalized chil-dren aged 0-18 years participating in a quality improvement program, where all ILI patients underwent virologic testing at the National Reference Centre followed by de-tailed recording of their clinical course. The direct (medical or non-medical) and indirect costs of inpatient management outside the ICU (“non-ICU”) versus management requiring ICU-care (“ICU”) added up to 2,767.14€ (non-ICU) vs. 29,941.71€ (ICU) for Influenza, 2,713.14€ (non-ICU) vs. 16,951.06€ (ICU) for RSV infections, and 2,767.33€ (non-ICU) vs. 14,394.02€ (ICU) for human rhinovirus (hRV) infections, respectively. Non-ICU inpatient costs were similar for all 8 RVI studied: Influenza, RSV, hRV, ade-novirus (hAdV), metapneumovirus (hMPV), parainfluenzavirus (hPIV), bocavirus (hBoV) and seasonal coronavirus (hCoV) infections. ICU-costs for Influenza however, ex-ceeded all other RVI. At the time of the study, Influenza was the only RVI with antivi-ral treatment options available for children, but only 9.8% of Influenza patients (non-ICU) and 1.5% of ICU-patients with Influenza received antivirals; only 2.9% were vac-cinated. Future studies should investigate the economic impact of treatment and pre-vention of Influenza-, COVID-19-, and RSV post vaccine introduction.

Background We aimed to evaluate the effectiveness of the ALRYNGO channel-type video laryngoscope with an AI-based glottis guidance system in senior emergency medicine residents for endotracheal intubation. Methods We enrolled twenty patients would be adequate for each device (direct laryngoscope, Pentax-AWS, and ALRYNGO). Before intubation, six senior residents wore a personal protective equipment. To randomize the device in this clinical study, a sealed envelope containing a device-specific identification card was utilized. When intubation began, the person who measured the intubation time divided the total intubation time into three-time intervals. The primary outcome was the intubation time. The secondary outcomes were the glottis view using the Cormack-Lehane grade (C-L grade) and the glottis guidance performance of ALRYNGO’s artificial intelligence. Results In Pentax-AWS and ALRYNGO, all intubations were successful, but the intubation time was longer than with the direct laryngoscope. And among the three, the ALRYNGO and Pentax-AWS had the highest frequency of C-L grade I (easiest intubation) at 80%, and the direct laryngoscope had the lowest frequency of 10%. Conclusions Even if healthcare professionals without experience with the channel-type video laryngoscope improve their performance on airway mannequins after training, their intubation performance may differ when applied to actual patients.

This work reports the influence of reduced graphene oxide (rGO) support on the catalytic performance of Cu@PtRu/rGO catalysts towards methanol oxidation in acidic medium. These core-shell catalysts are synthesized by the reduction method in two steps being the first using ethylene glycol to obtain Cu/rGO and the second, the reduction of copper atoms synthesized in the previous step to produce Cu@PtRu/rGO. In order to compare the catalytic performance of the prepared catalysts, Pt/C, PtRu/C, Cu@PtRu/C catalysts are also synthesized on Vulcan XC-72R carbon. The theoretical loading of Pt used in the Vulcan XC-72R carbon supported catalysts is equal to that utilized in Cu@PtRu/rGO, and higher in the other prepared catalysts. The surface composition of the nanoparticles, as well as their sizes, particle size distribution and morphology of the catalyst particles are characterized by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Cyclic voltammetry (CV) and chronoamperometry (CA) are employed to measure the electrochemical performance of the prepared catalysts. The anodic scans show that for the region of technological interest (0.1 to 0.4 V), the Cu@PtRu/rGO-16 electrocatalyst exhibits higher current density value than the others as a result of its lower starting oxidation potential (0.250V against 0.437V for Pt/C) and its higher ratio between forward (iF) and reverse (iR) current densities (iF/iR 1.45 against 0.93 for Pt/C). Chronoamperometric tests depict that the current density value of Cu@PtRu/rGO-16 catalyst is about 4 times higher than that of Cu@PtRu/C-16 and Cu@PtRu/C-18 catalysts, ca. 4.8 times higher than that of PtRu/C-30 catalyst and around 6 times higher than that of Pt/C-30. These results suggest that Cu@PtRu/rGO-16 exhibits high bulk activity for the electrooxidation of methanol, high stability and high tolerance to CO poisoning, making it possible to reduce the platinum loading in proton exchange membrane fuel cells (PEMFCs).

Nanoscale structuring/printing is of interest for range of applications in 3D subtractive and additive manufacturing (3D^+/-). Basic principles of light field enhancement and control at the nanoscale are overviewed in this section/chapter for bulk, surface, and localised plasmons (1D, 2D, and 3D localisation, respectively). All these plasmons are resonant phenomena which have common Lorentzian spectral lineshape which relates refractive and absorption properties as well as defining the phase of transmitted and scattered light. Localisation of light at the nanoscale creates the possibility of modification with matching resolution. Harnessing this light enhancement can be demonstrated as a "nano-pen" for direct write nanolithography.

Semantically meaningless strings that are associated with affective attributes (US) can become emotionally valenced CS. Jurchiș et al (2020) recently demonstrated CS-US associations may influence evaluations towards previously-unseen letter strings if the latter share grammar construction rules with CS. We replicated those authors' findings in a modified extension (Experiment 1; N₁ = 108), where happy/angry faces (US) were differentially associated with letter strings (CS) constructed using familiar (English) or non-familiar (Phoenician) alphabets. CS-US sequences were sandwiched by evaluations of strings that never appeared as CS, but shared grammar construction rules. However, post-hoc tests indicated valence effects were restricted to participants classified as 'high awareness' or those who had been exposed to longer stimulus durations, suggesting resource-intense deliberations were central during evaluations. Qualitative awareness checks additionally showcased many participants had attributed valences to recurring elements across conditioned and evaluated exemplars. These limitations were collectively addressed in Experiment 2 (N₂ = 140), where participants viewed Phoenician (/English) CS during conditioning but viewed English (/Phoenician) strings during evaluations, meaning no strings nor elements recurred between phases. We found credible valence effects across English and Phoenician strings, with the latter observed across all awareness categories. Because participants were unable to consciously specify any evaluative strategies while evaluating Phoenician strings, we speculate grammar construction rules (organizing relations) may have been non-consciously acquired during conditioning.

The structure of turbulent flow over non-flat surfaces is a topic of major interest in practical applications in both engineering and geophysical settings. A lot of work has been done in the fully rough regime at high Reynolds numbers where the effect on the outer layer turbulence structure and the resulting friction drag is well documented. It turns out that surface topology plays a significant role on the flow drag especially in the transitional roughness regime and therefore, hard to characterize. Survey of literature shows that roughness function depends on the interaction of roughness height, flow Reynolds number and topology shape. In addition, if the surface topology contains large enough scales then it can impact the outer layer dynamics and in turn modulate the total frictional force. Therefore, it is important to understand the mechanisms underlying drag increase from systematically varied surface undulations in order to better interpret quantifications based on mean statistics such as roughness function. In this study, we explore the mechanisms that modulate the turbulence structure over a two-dimensional (2D) sinusoidal wavy surface with a fixed amplitude, but varying slope. To accomplish this, we model the turbulent flow between two infinitely wide 2D wavy plates at a friction Reynolds number, $Re_{\tau}=180$. We pursue two different but related flavors of analysis. The first one adopts a roughness characterization flavor of such wavy surfaces. The second one focuses on understanding the non-equilibrium near surface turbulence structure and their impact on roughness characterization. Analysis of the different statistical quantifications show strong dependence on wave slope for the roughness function indicating drag increase due to enhanced turbulent stresses resulting from increased production of vertical velocity variance from the surface undulations.

Direct mass spectrometry-based metabolomics has been widely employed in the last years to characterize metabolic alterations underlying to Alzheimer’s disease development and progression. This high-throughput approach presents a great potential for fast and simultaneous fingerprinting of a vast number of metabolites, which can be applied to multiple biological samples such as serum/plasma, urine, cerebrospinal fluid and tissues. In this review article we present the main advantages and drawbacks of metabolomics based on direct mass spectrometry compared with conventional analytical techniques, and provide a comprehensive revision of the literature on the application of these tools in Alzheimer’s disease research.

We assume that the current mathematical knowledge K is a finite set of statements from both formal and constructive mathematics, which is time-dependent and publicly available. Any theorem of any mathematician from past or present belongs to K. The set K exists only theoretically. Ignoring K and its subsets, sets exist formally in ZFC theory although their properties can be time-dependent (when they depend on K) or informal. In every branch of mathematics, the set of all knowable truths is the set of all theorems. This set exists independently of K. Algorithms always terminate. We explain the distinction between algorithms whose existence is provable in ZFC and constructively defined algorithms which are currently known. By using this distinction, we obtain non-trivial statements on decidable sets X⊆N that belong to constructive and informal mathematics and refer to the current mathematical knowledge on X. This and the next sentence justify the article title. For any empirical science, we can identify the current knowledge with that science because truths from the empirical sciences are not necessary truths but working models of truth about particular real phenomena.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

Group IV alloys of GeSn have been extensively investigated as a competing material alternative in short-wave to mid-infrared photodetectors (PDs). The relatively large defect densities present in GeSn alloys are the major challenge in developing practical devices, owing to the low-temperature growth and lattice mismatch with Si or Ge substrates. In this paper, we comprehensively analyze the impact of defects on the performance of GeSn p-i-n homojunction PDs. We first present our theoretical models to calculate various contributing components of the dark current including minority carrier diffusion in p- and n-regions, carrier generation-recombination in the active intrinsic region, as well as the tunneling effect. We then analyze the effect of defect density in the GeSn active region on carrier mobilities, scattering times and the dark current. A higher defect density increases the dark current, resulting in reduction in detectivity of GeSn p-i-n PDs. In addition, at low Sn concentrations, defect-related dark current density is dominant, while the generation dark current becomes dominant at a higher Sn content. These results point to the importance of minimizing defect densities in the GeSn material growth and device processing, particularly for higher Sn compositions necessary to expand the cutoff wavelength to mid- and long-wave infrared regime. The study provides more of realistic expectations and guidelines for evaluating GeSn p-i-n PDs as a competitor to the III-V and II-VI-based infrared PDs currently on the commercial market.

Near Inertial Oscillations (NIOs) are ocean oscillations forced by intermittent winds. They are most energetic at mid-latitudes, particularly in regions of atmospheric storm tracks. Wind-driven, large-scale NIOs are quickly scattered by ocean mesoscale eddies (with sizes ranging from 100 to 400 km), causing a significant portion of the NIO energy to propagate into the ocean interior. This kinetic energy pathway illustrates that the wind energy input to NIO, estimated at 5 TeraWatts, is critical for maintaining deep ocean stratification and thus closing the total kinetic energy budget, as emphasized by numerous modelling studies. However, this wind energy input to NIO remains poorly observed on a global scale. A remote sensing approach, which observes winds and ocean currents co-located in time and space with high resolution, is necessary to capture the intermittent air-sea coupling. The current satellite observations do not meet these requirements. This study assesses the potential of a new satellite mission concept, Ocean DYnamics and Surface Exchange with the Atmosphere (ODYSEA), to recover wind-forced NIOs from co-located winds and currents. To do this, we use an Observation System Simulation Experiment (OSSE) based on hourly observations of ocean surface currents and surface winds from five surface moorings covering latitudes from 15∘ to 50∘. ODYSEA wind and current observations are expected to have a spatial resolution of 10 km with about 12-hour sampling frequency in mid-latitudes. Results show that NIOs can be recovered with high accuracy using the ODYSEA spatial and temporal resolution, only if observations are made in a wide-swath of 1,800 km. A narrower swath (1,000 km) may lead to significant aliasing.

The Maxwell equations of electrodynamics describe electrical and magnetic forces with great accuracy in the vacuum of space. But the equations of electrodynamics applied to material systems are usually written in a way that obscures their accuracy. The usual formulation of the Maxwell equations includes a dielectric constant as a single real number that grossly over-approximates the actual properties of matter, particularly liquid matter so important in applications of electrodynamics to biology and chemistry. We rewrite two Maxwell equations here to make clear the precision of the Maxwell equations in the presence or absence of matter. We discuss and derive two well known corollaries that are as universal and precise as the Maxwell equations themselves: (1) a continuity equation that relates charge and flux and (2) a conservation equation in which total current never accumulates at all. The total current is the right hand side of the Ampere-Maxwell law. Total current is perfectly incompressible. It is conserved exactly, everywhere and at every time, independent of the microphysics of charge conduction. The total current combines the flux of charges and the ethereal current. The ethereal current \varepsilon_{o\ }\sfrac{\partial\mathbf{E}}{\partial t}\ exists everywhere, including the interior of atoms, because it is a property of space, not matter. The ethereal current exists, and thus flows, in a vacuum devoid of mass. The ethereal current is a consequence of the relativistic (Lorentz) invariance of charge. Charge does not change even if it moves at speeds approaching the velocity of light. Total current has properties quite distinct from flux of mass because of the ethereal current. Most strikingly, in the one dimensional unbranched systems of electronic circuits and biological ion channels, the total current is independent of location, even if the flux of charges varies a great deal. Indeed, the Maxwell equations—and thus conservation of total current—act as a perfect low pass spatial filter, converting the infinite variation of (the Brownian model of) thermal motion of charges to the zero variation of the total current.

Electrodynamics is usually written using polarization fields to describe changes in distribution of charge as electric fields change. This approach does not specify polarization fields uniquely from electrical measurements. Many polarization fields will produce the same electrodynamic forces and flows because only divergence of polarization enters Maxwell’s first equation, relating charge and electric field. The curl of any function can be added to a polarization field without changing the electric field at all. The divergence of the curl is always zero. To be unique, models must describe the charge distribution and how it varies. I propose a different paradigm to describe field dependent charge, i.e., the phenomenon of polarization. This operational definition of polarization has worked well in biophysics for fifty years, where a field dependent, time dependent polarization provides gating current that makes neurons respond sensitively to voltage. Theoretical estimates of polarization computed with this definition fit experimental data. I propose that operational definition be used to define polarization charge in general. Charge movement needs to be computed from a combination of electrodynamics and mechanics because ‘everything interacts with everything else’. The classical polarization field need not enter into that treatment at all. When nothing is known about polarization, it is necessary to use an approximate representation with a dielectric constant that is a single real positive number. This approximation allows important results in some cases, e.g., design of integrated circuits in silicon semiconductors, but can be seriously misleading in other cases, e.g., ionic solutions.

Condition monitoring of bearings is an open issue. The use of the stator current to monitor induction motors has been validated as a very advantageous and practical way to detect several types of faults. Nevertheless, for bearing faults the use of vibrations or sound generally offers better results in the accuracy of the detection although with some disadvantages related to the sensors used for monitoring. To improve the performance of bearing monitoring, it is proposed to take advantage of more information available in the current spectra, beyond the usually employed, incorporating the amplitude of a significant number of sidebands around the first eleven harmonics, growing exponentially the number of fault signatures. This is especially interesting for inverter-fed motors. But, in turn, this leads to the problem of overfitting when applying a classifier to perform the fault diagnosis. To overcome this problem, and still exploit all the useful information available in the spectra, it is proposed to use shrinkage methods, which have been lately proposed in machine learning to solve the overfitting issue when the problem has much more variables than examples to classify. A case study with a motor is shown to prove the validity of the proposal

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

The laser sintering process and modification of electrophoretic deposition (EPD) YSZ coatings on YSZ air plasma sprayed thermal barrier coatings (TBCs) were investigated. Ni-based superalloy was plasma sprayed using yttria-stabilized zirconia (YSZ) to perform thermal barrier coating with 400 μm thickness. The electrophoretic deposition (EPD) technique was used for depositing nanopowder of YSZ on the surface of YSZ TBCs. In this study, a technology of direct sintering the green EPD layer by laser beam was carried out. The best conditions of deposition YSZ overlay coating using DC current were obtained with applied voltage 40 V, deposition time 5 min, and suspension concentration 10 g/l. Iodine was added to the solutions as the stabilizing agent. To overcome the disadvantages of high sintering temperatures, laser sintering was taken as a new approach. Microstructures for all specimens were studied using Field Emission Scanning Electron Microscopy (FESEM) with EDS analysis. Surface roughness was investigated using AFM analysis and central line average (CLA). The results indicated that the morphology after the direct laser sintering of the EPD layer has a fine and controllable grain size, high hardness, and low roughness. Which is better than the direct laser on plasma-sprayed coatings.

With an increasing concern for global warming, there have been many attempts to reduce greenhouse gas emissions. About 30 % of total energy has been consumed by buildings and much attention has been paid to reducing building energy consumption. While there are many ways of reducing building energy consumption, accurate energy consumption prediction becomes more significant. As mechanical systems are the most energy-consuming components in the building, the present study developed the energy consumption prediction model for a direct-fired absorption chiller by using the ANN technique for the short term. The ANN model was optimized and validated with the actual data collected through a BAS. For the optimization, the numbers of input variables and neurons, and the data size of training were applied. By changing these parameters, the predictive performance was analyzed. In sum, the outcome of the present study can used to predict the energy consumption of the chiller as well as improve the efficiency of the energy management. The outcome of the present study can be used to develop a more accurate prediction model with a few datasets in that it can improve the efficiency of building energy management.

Breast cancer (BC) is a heterogeneous disease representing a substantial economic burden. In order to develop policies that successfully decrease this burden, the factors affecting costs need to be fully understood. Evidence suggests that early detection in Stage I has a lower cost than late detection. We aim to provide conservative estimates of BC's stage-wise medical costs from German healthcare and the payer's perspective. To this end, we conducted a literature review of articles evaluating stage-wise costs of BC in Germany through PubMed, Web of Science, and Econ Lit databases supplemented by Google Scholar. We developed a decision tree model to estimate BC related medical costs in Germany using available treatment and cost information. The review generated seven studies; none estimated the stage-wise costs of BC. The studies were classified into two groups: (1) case scenarios (five studies) and two studies based on administrative data. The first sickness funds data study (Gruber, Stock, et al. 2012) used 1999 information to approach BC attributable cost; their results suggest a range between €3,929 and €11,787 depending on age. The second study (Kreis, Plöthner, et al. 2020) used 2011-2014 data and suggested an initial phase incremental cost of €21,499, an intermediate phase cost of €2,620, and a terminal phase cost of €34,513 per incident case. Our decision tree model based BC stage-wise cost estimates were €21,523 for Stage I, €25,679 for Stage II, €30,156 for Stage III, €42,086 for Stage IV. Alternatively, the modeled cost estimates are €20,284 for the initial phase of care, €851 for the intermediate phase of care, and €34,963 for the terminal phase of care. Our estimates for phases of care are consistent with recent German estimates provided by Kreis and Plöthner et al. Furthermore, the data collected by sickness funds are collected primarily for reimbursement purposes, where the German ICD-10 classification system defines a cancer diagnosis. As a result, claims data lack the clinical information necessary to understand stage-wise BC costs. Our model-based estimates fill the gap and inform future economic evaluations of BC interventions.