Resistive random-access memory has emerged as a promising non-volatile memory technology, garnering substantial attention due to its potential for high operational performance, low power consumption, and scalability. Two-dimensional nanostructured materials play a pivotal role in RRAM devices, offering enhanced electrical properties and physical attributes that contribute to overall device improvement. In this study, self-rectifying switching behavior in RRAM devices is proposed based on molybdenum disulfide nanocomposites decorated with palladium on SiO2/Si substrates. The integration of Pd and MoS2 at the nanoscale effectively mitigates leakage currents decreasing from cross-talk in the RRAM array, eliminating the need for a separate selector device. The successful demonstration of the expected RRAM switching behavior follows the application of a Pd nanoparticle coating. The fabricated Pd-MoS2 synaptic device showed a high current ratio for forward/reverse current higher than 60 at a low resistance state and observed a memory on/off ratio of 103 performing stable resistance switching behavior.

: In the automotive industry, high-strength plates have been increasingly used to reduce the vehicle body weight due to stringent regulations on fuel economy and safety. Such plates achieve tensile strengths as high as 1.5 GPa owing to the hot-stamping process. However, these plates suffer from scale generation and surface decarburization because of the surface oxidation of the material. Recently, studies on materials subjected to high-frequency induction heating have reported strength improvement owing to the coil shape and cooling method. This study presents the surface temperature changes, mechanical properties, and microstructures of boron steels subjected to longitudinal heating, which uses eddy currents generated from high-frequency induction heating. The surface temperature data were analyzed under different high-frequency induction heating powers (15, 18, 21, 24, 27, and 30 kW) and distances from the specimen (6, 9, and 15 mm). The mechanical properties and microstructures were also analyzed in different high-frequency induction heating coil directions. The correlations between the high-frequency induction heating power and the distance from the specimen with the maximum tensile strength were determined.

The battle of currents between AC and DC reignited as a result of the development in the field of power electronics. The efficiency of DC distribution systems is highly dependent on the efficiency of distribution converter, which calls for optimized schemes for efficiency enhancement of distribution converters. Modular solid-state transformers play a vital role in DC Distribution Networks and Renewable Energy systems (RES).This paper deals with efficiency-based load distribution for Solid State Transformers (SSTs) in DC distribution networks. Aim is to achieve a set of minimum inputs that are consistent with output while considering constraints and efficiency. As the main feature of modularity is associated with a three-stage structure of SSTs. This modular structure has been optimized using Ant Lion Optimizer (ALO) and validated by applying it EIA (Energy Information Agency) DC Distribution Network which contains SSTs. In the DC distribution grid, modular SSTs provide promising conversion of DC power from medium voltage to lower DC range (400V). The proposed algorithm is simulated in MATLAB and also compared with two other metaheuristic algorithms. The obtained results prove that the proposed method can significantly reduce input requirements for producing the same output while satisfying the specified constraints.

Article contents the analytical model of the drift of a separate ice field under action of wind and current, which velocities and directions can vary during time. Model takes into account the mass of ice, added mass of sea water and the effects of the wind and current on the ice field in form the friction on its upper and underwater surfaces and frontal resistance on its end (forward and backward) surfaces. Results of performed the steady wind drift of the ice fields modelling show the drift velocity exceeds considerable known velocity of a compact ice cover wind drift. Drifting ice field has the certain kinetic energy that should be released when collision with unmovable obstacle and spent on brittle breakdown of part of the ice field. Volume of formed small ice pieces (fragments of ice field) was estimated by comparison of the specific energy of the sea ice brittle destruction and the kinetic energy of drifting ice field. Article presents the results of estimation of possible volume of the ice pieces and the scales of formed piles as result of collision with an obstacle depending on initial dimensions of ice field and wind speed. Developed models and the results of computer modelling can be used to estimate the ice pile sizes near the stationary platforms and terminals on the Arctic seas.

The digital twin (DT) research field is experiencing rapid expansion, yet the research in industrial practices in this area remains poorly understood. This paper aims to address this knowledge gap by sharing feedback and future requirements from the manufacturing industry. The methodology employed in this study involves an examination of a survey that received 99 responses and interviews with 14 experts from 10 prominent UK organisations, most of which are in the defence industry in the UK. The survey and interviews explored topics such as DT design, return on investment, drivers, inhibitors, and future directions for DT development in manufacturing. The study findings indicate that DTs should possess characteristics such as adaptability, scalability, interoperability, and the ability to support assets throughout their entire life cycle. On average, completed DT projects reach the break-even point in less than two years. The primary motivators behind DT development were identified to be autonomy, customer satisfaction, safety, awareness, optimisation, and sustainability. Meanwhile, the main obstacles include a lack of expertise, funding, and interoperability. The study concludes that the federation of twins and a paradigm shift in industrial thinking are essential components for the future of DT development.

The aim of the study was to find the effect of polyethylene (PE) coatings on the short-circuit current of silicon photovoltaic cells covered with glass, in order to improve the short-circuit current of the cells. Various combinations of PE films (thicknesses ranging from 9 to 23 µm, number of layers ranging from 2 to 6) with glasses (greenhouse, float, optiwhite and acrylic glass) were investigated. The best current gain of 4.05% was achieved for the coating combining a 1.5 mm-thick acrylic glass with 2 × 12 µm-thick PE films. This effect can be related to the formation of an array of micro-wrinkles and micrometer-sized air bubbles with a diameter of 50 to 600 µm in the films, which serve as micro-lenses and enhance light trapping.

ADHD, a neurodevelopmental condition, is distinguished by a triad of symptoms including inattention, hyperactivity, and impulsivity. It is frequently accompanied by comorbidities such as anxiety, depression, and learning disabilities. As a result, clinicians often face challenges in accurately diagnosing ADHD and differentiating it from other conditions. As a prospective remedy for ADHD, scientists have investigated Transcranial Direct Current Stimulation (tDCS), a non-invasive technique of stimulating the brain. It involves applying low-intensity electrical currents to specific regions of the brain to modulate neural activity. This review paper aims to provide an overview of the comorbidities associated with ADHD and the differential diagnosis of the condition. It also explores the potential of tDCS as a treatment option for ADHD, including its mechanisms of action and efficacy in improving ADHD symptoms. The comorbidities discussed in this review include anxiety disorders, mood disorders, and substance use disorders. These comorbidities are frequently seen in individuals with ADHD and can complicate the diagnosis and treatment of the condition. The paper also highlights the importance of considering comorbidities when assessing ADHD, as well as the potential impact of these conditions on treatment outcomes. The differential diagnosis section of the paper explores conditions that can present with symptoms similar to ADHD, such as anxiety disorders, mood disorders, and learning disabilities. It emphasizes the need for a thorough assessment and differential diagnosis to identify ADHD and differentiate it from other conditions accurately. The final section of the paper discusses the potential of tDCS as a treatment option for ADHD. It examines the mechanisms of action of tDCS and its efficacy in improving ADHD symptoms, including attention, hyperactivity, and impulsivity. It also explores the potential for tDCS to improve comorbid conditions associated with ADHD. Overall, this review provides a comprehensive overview of comorbidities and differential diagnoses in ADHD and the potential of tDCS as a treatment option. The paper highlights the importance of a thorough assessment and personalized treatment plan for individuals with ADHD, particularly those with comorbidities.

Solar cosmic rays (SCR) are generated during the primordial energy release in solar flares. This explosive process takes place in the solar corona above the active region. It represents fast release of the magnetic field energy of the current sheet, which is formed near a singular magnetic field line. Solar cosmic rays appear as a result of acceleration of charged particles, mainly protons, by an inductive electric field in the current sheet, equal to the field E=V´B/c near the current sheet. To study the mechanism of solar flares and obtain conditions for stydy SCR acceleration it is necessary to carry out magnetohydrodynamic (MHD) simulation of a flare situation in the solar corona above a real active region. The methods of stabilization were developed which made it possible to solve partially the problem of numerical instabilities. MHD simulations showed complicated configuration near the singular line. Comparison of the results of MHD simulations with observations showed a general agreement of the positions of the current sheets with regions of intense flare radiation. However, there are some problems with the details of such coincidences. The results show the possibility of improving the methods of MHD simulation in order to solve the arisen problems.

Electromagnetic sensing has been used for diverse applications of non-destructive testing, including the surface inspection, measurement of properties, object characterization. However, the measurement accuracy could be significantly influenced by the lift-off between sensors and samples. To address the issue caused by lift-offs, various strategies have been proposed for the permeability measurement of ferromagnetic steels, which mainly involves different sensor designs and signal features (e.g., the zero-crossing feature). In this paper, a single high-frequency scenario for the permeability retrieval is introduced. By combining the signal of two sensing pairs, the retrieval of magnetic permeability is less affected by the lift-off of sensors. Unlike the previous strategy on reducing the lift-off effect (directly taking the phase term out of the integration) using the Dodd-Deeds analytical method, the proposed method is based on a high-frequency linear feature of the phase term. Therefore, this method has the merit of high accuracy and fast processing for the permeability retrieval (a simplified version of Dodd-Deeds analytical formulas after the integration). Experimental measurement has been carried out on the impedance measurement of designed sensors interrogating ferromagnetic dual-phase steels. For sensor lift-offs of up to 10 mm, the error of the permeability retrieval is controlled within 4 % under the optimal frequency.

An adaptive control technique has been implemented for DSTATCOM for power quality enhancement in three phase four wires(3P4W) distribution system. The reference source currents are extracted from active components of load current for each phase by using this technique. It has also been used for load balancing, harmonic suppression, power factor improvement and reactive power compensation in distribution system. The adaptive control technique has been tested at varying load in steady state and dynamic conditions. This technique is developed using MATLAB/Simulink and source side harmonics are mitigated under different load conditions which are acceptable in accordance with IEEE standard.

Aiming for the problems emerging in the PWM drive system with long cables, accurate modeling of power cables is the premise to predict and analyze the relevant phenomenon, and a proper filter design is the key solution to these problems. This paper proposes high-frequency cable models to represent the frequency-dependent characteristics, especially for the high-frequency resistance of the cable that is an easily overlooked factor but determines the damping of overvoltage. The proposed models can be used for accurately representing the cable parameters in a wide frequency range, and correctly simulating the differential mode (DM) overvoltage and common mode (CM) current, including the peak value, oscillation frequency and damping of the transient waveform. In addition, improved filter networks are proposed to suppress the DM voltage and CM current, with the merit of low losses, small volume and an excellent ability of suppressing overvoltage. The proposed cable models and the filter design have been validated in a 750W PWM drive system with 200m power cables.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

In this paper we develop from first principles a unique law pertaining to the flow of fluids through closed conduits. This law, which we call “Quinn’s Law”, may be described as follows: When fluids are forced to flow through closed conduits under the driving force of a pressure gradient, there is a linear relationship between the normalized dimensionless pressure gradient, P_Q, and the normalized dimensionless fluid current, C_Q. The relationship is expressed mathematically as: P_Q = k₁ +k₂C_Q. This linear relationship remains the same whether the conduit is filled with or devoid of solid obstacles. The law differentiates, however, between a packed and an empty conduit by virtue of the tortuosity of the fluid path, which is seamlessly accommodated within the normalization framework of the law itself. When movement of the fluid is very close to being at rest, i.e., very slow, this relationship has the unique minimum constant value of k₁, and as the fluid acceleration increases, it varies with a slope of k₂ as a function of normalized fluid current. Quinn’s Law is validated herein by applying it to the data from published classical studies of measured permeability in both packed and empty conduits, as well as to the data generated by home grown experiments performed in the author’s own laboratory.

In the present work, a superlattice structure comprising superconducting and insulator layers is studied. Here, if a magnetic field is applied parallel to the layers, the lack of a pinning center leads to a novel transition; in particular, as the applied magnetic field is reduced, the stationary wave surrounding the magnetic flux quantum in the superconducting layer eventually collides with the superconducting–insulating interfaces on both sides because its radius becomes larger than the width of the superconducting layer. At this instant, the stationary wave will collapse, and a transition will occur: the magnetic quanta are collapsed and thus the uniform magnetic field distribution is achieved, which corresponds to the transition from the superconducting state to the normal state over critical current. Considering a one-dimensional model of the structure, a critical current density equation is derived that indicates an increase in the critical current density for increased applied magnetic field. Subsequently, the same calculation was conducted after changing the direction of the magnetic field component, and the combination of these two calculations expresses the anisotropic property of the structure. The phenomenon is also predicted for anisotropic critical current density. This phenomenon is an important discovery that helps manufacture high-temperature superconducting tape as well as large high-temperature superconducting coils.

Protective coatings, in recent years also from nanocomposite formulations, are commonly applied onto architectural stone and stone artefacts, mainly to prevent absorption into the porous stone structure of condensed water and dissolved atmospheric pollutants. While standard protocols are available to assess a coating’s performance, understanding the response of the coating-stone system is a complex task, due to the interplay of various factors determining the overall behaviour. Characterization techniques allowing to correlate the extent and nature of surface modification upon treatment with the most relevant physical properties (i.e water absorption and surface wettability) are thus of great interest. Electrokinetic analysis based on streaming current measurements, thanks to its sensitivity towards even minor changes in the surface chemical composition, may fulfil such requirement. Indeed, by involving the interaction with a testing aqueous electrolyte solution, this technique allows to probe not only the outer surface but also the outermost layer of the pore network, which plays a crucial role in the interaction of the stone with condensed atmospheric water. In this work a correlation was found between the extent of surface modification, as determined by streaming current measurements, surface wettability and capillary water absorption of 6 coating-lithotype combinations (3 lithotypes and 2 nanocomposites).

This paper analyzes the measurement error, caused by the position of the current-carrying conductor, of circular array of magnetic sensors for current measurement. The circular array of magnetic sensors is an effective approach for AC or DC non-contact measurement, as its low cost, large linear range, wide bandwidth, light weight and low noise. Especially it has claimed that such structure has the excellent reduction ability for the errors caused by the position of the current-carrying conductor, crosstalk current interference, shape of the conduction cross section and the earth magnetic field. However, the positions of the current-carrying conductor, including un-center and un-perpendicularity, has not analyzed in detail until now. In this paper, the theoretical analysis has been proposed based on vector inner and exterior product. In the presented mathematical model of relative error, the un-center offset distance, the un-perpendicular angle, the radius of the circle and the number of the magnetic sensor are expressed in one equation. The comparison of the relative error caused by the position of the current-carrying conductor between four and eight sensors is conducted. The Tunnel Magnetoresistance (TMR) sensors are used in the experimental prototype to verify the mathematical model. The analysis results can be the reference to design the detail of circular array of magnetic sensors for current measurement in practical situation.

Current-quark masses are compared to the rest masses allowed by the Helmholtz equation in a polar model. Within the uncertainty of the current u quark mass determination, the current quark mass coincides with the rest mass allowed by the Helmholtz equation in the polar model in accordance with the second root of the zero Neumann function. Current d quark mass coincides with the rest mass calculated in accordance with the third root of the Bessel zero function. On the basis of a comparison of these results with the results obtained earlier for ordinary real particles u and d quarks stability is discussed.

The excitation of the visual system increases with increasing retinal illumination. At the same time, the sensitivity of the system decreases (light adaptation). Higher excitation automatically results in a lower sensitivity. This study investigates whether this parallelism between the excitation and the sensitivity also applies in the dynamic case, that is, during the transition to a higher excitation level after an increase in the retinal illuminance. For this purpose, the courses of the subjective and the electroretinographic threshold during the transitional phase after a step of the adaptation illumination was determined by means of a special light-stimulation apparatus. As a measure of the course of the excitation during this time, the response ERG on the adaptation step was recorded with a special amplifier. The threshold curve always has an overswing, which shows subjectively very strong differences. It can be concluded that the glare caused by a sudden increase in illuminance is subjectively very different. The comparison between the response ERG on the adaptation step and the course of the electroretinographic increment threshold during this time shows a broad agreement between the two courses. It can thus be assumed that the sensitivity of the visual system follows the course of the excitation also in the dynamic case. In addition, the investigation shows that the glare experienced after a step in the illuminance clearly shows great subjective differences.

Chronoamperometric curves of the oxidation of a ferrocenyl derivative by the potential step showed diffusion controlled-like currents less than the Cottrell's equation at a platinum wire electrode. The lower deviation cannot be explained by the Butler-Volmer heterogeneous kinetics, but was ascribed to the negatively capacitive current associated with the redox reaction. The deviation at the fully oxidized potential corresponds to the non-zero concentration at the electrode surface, which cannot be predicted from the Nernst equation. The Nernst equation expresses the relationship of the potential with the activity at the electrode surface rather than the concentration. The diffusion equation provides the relation of the current with the surface concentration rather than the activity. The negative capacitance or the non-zero concentration may arise from structure formation on the electrode owing to the dipole-dipole interaction, which is similar to the generation of the double layer capacitance including frequency dispersion. On this concept, we derive here expressions for the lowered diffusion-controlled current and the time-dependent surface concentration. The negatively capacitive current shows the time-dependence of t-0.9, which is similar to the decay of the double layer capacitive currents. The surface concentration decays with the t-0.4-dependence.

DC-connected parallel inverter systems are gaining popularity in industrial applications. However, such parallel systems generate excess current ripple (harmonics) at the DC-link due to harmonic interactions between the inverters in addition to the harmonics from the PWM switching. These DC-link harmonics cause the failure of fragile components such as DC-link capacitors. This paper proposes an interleaving scheme to minimize the current harmonics induced in the DC-link of such a system. The results show that when the carrier waves of the two inverters are phase-shifted by 90° angle, the maximum high-frequency harmonic ripple cancellation occurs, which reduces the overall RMS value of the DC-capacitor current.The outcome of this proposed solution is a cost-effective DC-harmonics mitigating strategy for the industrial designers to practically configuring multi-inverter systems, even when most of the drives are not operating at rated power levels. Experimental and simulation results presented in this paper verify the effectiveness of the proposed carrier-based phase-shifting scheme for two different configurations of common DC connected multi-converter systems.

Transcutaneous nerve stimulation has several neuromodulatory applications, including pain management, sensory restoration, and motor recovery. Transcutaneous stimulation delivered via electrode arrays offers ease of use and reconfigurability through non-invasive means. Also, employing electrode arrays allows regulation of the permeated electric fields for greater control over the stimulation performance. Field shaping involves the regulation of permeated electric fields and is a well-established practice for deep brain stimulation; however, its applicability to peripheral nerve stimulation still needs exploration. Adopting such techniques can help to overcome current limitations with transcutaneous stimulation, like poor targetability, early onset of fatigue, and perceived discomfort. This article provides a perspective on the applicability of field-shaping techniques in improving the overall stimulation outcome.

The pinning force density FpJc,B=Jc×B (where Jc is the critical current density and B is the applied magnetic field) is one of the main parameters that characterize the resilience of a superconductor to carry a dissipative-free transport current in an applied magnetic field. Kramer (1973 J. Appl. Phys. 44 1360), and Dew-Hughes (1974 Phil. Mag. 30 293) proposed a widely used scaling law for the pinning force density amplitude: FpB=Fp,max×p+qp+qppqq×BBc2p×1-BBc2q, where Fp,max, Bc2, p, and q are free-fitting parameters. Since the late 1970-s till now, several research groups have reported experimental data on the dependence of Fp,max on the average grain size, d, in Nb3Sn-based conductors. Godeke (2006 Supercond. Sci. Techn. 19 R68) proposed that the dependence obeys the law Fp,maxd=A×ln1d+B. However, this scaling law has several problems, for instance, the logarithm is taken from a non-dimensionless variable, and Fp,maxd<0 for large grain sizes, and Fp,maxd→∞ for d→0. Here, we reanalysed the full inventory of publicly available Fp,maxd data for Nb3Sn conductors and found that the dependence can be described by Fp,maxd=Fp,max0×exp-dδ law, where the characteristic length, δ, varies within a remarkably narrow range, that is, δ=175±13 nm, for samples fabricated by different technologies. The interpretation of the result is based on the idea that the in-field supercurrent flows within a thin surface layer (thickness of δ) near the grain boundary surfaces (similar to London’s law, where the self-field supercurrent flows within a thin surface layer with a thickness of the London penetration depth, λ, and the surface is a superconductor-vacuum surface). An alternative interpretation is that δ represents the characteristic length of the exponential decay flux pinning potential from the dominant defects in Nb3Sn superconductors, which are grain boundaries.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Stray current is a relevant phenomenon in particular for DC electrified transportation systems, affecting the track and infrastructure within the right of way and other structures and installations nearby. It worsens with time and the level of protection depend on timely maintenance, besides correct design choices. The assessment of track insulation is the starting point for both stray current monitoring systems and at commissioning or upon major changes. Standardized methods (ref. EN 50122-2, or IEC 62128-2) are almost unchanged in the last 20 years, but suffer from accuracy issues and variability due to parameters and conditions not under operator’s control. A critical discussion and analysis of the sources of variability and practical constraints is proposed, followed by the evaluation of uncertainty, with the objective not only to assess the accuracy of provided results, but to foster research on innovative, more flexible and accurate, methods.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

This paper reports the effect of silicon substrate orientation and aluminum nitride buffer layer deposited by molecular beam epitaxy on the growth of aluminum nitride thin films deposited by DC magnetron sputtering technique at low temperature. The structural analysis has revealed a strong (0001) fiber texture for both substrates Si (100) and (111) and a hetero-epitaxial growth on few nanometers AlN buffer layer grown by MBE on Si (111) substrate. SEM images and XRD characterization have shown an enhancement in AlN crystallinity thanks to AlN (MBE) buffer layer. Raman spectroscopy indicated that the AlN film was relaxed when it deposited on Si (111), in compression on Si (100) and under tension on AlN buffer layer grown by MBE/Si (111) substrates, respectively. The interface between Si (111) and AlN grown by MBE is abrupt and well defined; contrary to the interface between AlN deposited using PVD and AlN grown by MBE. Nevertheless, AlN hetero-epitaxial growth was obtained at low temperature (<250°C).

A new picture of the Josephson effect is devised. The radio-frequency (RF) signal, observed in a Josephson junction, is shown to stem from bound electrons, tunneling periodically through the insulating film. This holds also for the microwave mediated tunneling. The Josephson effect is found to be conditioned by the same prerequisite worked out previously for persistent currents, thermal equilibrium and occurence of superconductivity. The observed negative resistance behaviour is shown to originate from the interplay between the normal and superconducting currents.

The Chile-Peru subpopulation (CPe) of the southern right whale (Eubalaena australis) is classified as critically endangered following intense whaling in past centuries. Due to their very low abundance, information on breeding and feeding grounds is also scarce. Unmanned aerial vehicles (UAVs) are increasingly applied in marine mammal research thanks to their low cost and relative ease of use. This case study documents a southern right whale nursing in Bahía Moreno (23ºS), Antofagasta, northern Chile, through high-resolution images taken by UAV of a lone adult in July 2019 and the same (photo-identified) whale with a neonate in August, confirming local parturition. Combined with earlier data we hypothesize that the Antofagasta Region may be a calving and nursing ground for the CPe subpopulation. Given the intense shipping traffic and fishing activities around the Mejillones Peninsula and Antofagasta port, priorly recommended marine spatial planning to help avoid net entanglements and vessel collisions of fin and humpback whales would also contribute to the conservation of the CPe stock of southern right whale.

In this work, it is analyzed a Digital Signal Processor, DSP, based One Cycle Control, OCC, strategy for a Power Factor Corrector, PFC, rectifier, which presents Common-mode Voltage, CMV, immunity. The proposed strategy utilizes an emulated-resistance-controller in closed-loop configuration to set up dc-link voltage and achieve unity power factor, UPF. It is shown that if PFC can achieve UPF condition and if phase voltage is only affected by CMV, then phase current is free from CMV, as well as a lead-lag compensator, LLC, to average phase current. Another possible condition is also analyzed. The proposal is verified by simulation and experiments.

The eddy current loss should be optimized to be as less as possible for the stability of permanent magnet in high speed permanent magnet synchronous motor (HSPMSM) rotor and ensure the high efficiency and low temperature of the motor. This paper analyzes the eddy current distribution in rotor, with consideration of the conflict of the thickness of sleeve and diameter of the rotor, calculating the eddy current loss (ECL) and the thermal distribution via Separation of variables method for solving Maxwell's equations with analytical hieratical model of ECL constructed. The optimization result of ECL of the HSPMSM whose power and rated speed is 30kw 48000r/min can be got by multi-objective optimization method, combined weighting coefficient method and traversal algorithm based on chaotic local search particle swarm optimization (CLSPSO), utilizing ECL analytical model and other analytical constraints. Related experiment and measurement has been implemented with new approach of loss separation.

In this study, we applied a central composite design to estimate independent variables and establish optimal conditions of filtration rate and feces production that enhance filtration of suspended organic matter by the freshwater mussels Sinanodonta woodiana. The results indicated that statistical design methodology offers an efficient and feasible approach for high filtration and low feces production condition optimization. The proposed model equation takes into account the quantitative effect of variables and also the influence of interactions among variables on mussel filtration rate. Under the optimal experimental conditions (mussel size, 13.0 ± 0.2 cm; water current, 17.5 L/h), the experimental filtration rate of 4.47 ± 1.82 L/mussel/h showed a degree of correspondence with the predicted value of 8.4 L/mussel/h, which verified the practicability of this optimum strategy.

Building a new power plant to address the growing demand for power due to population concentration in the metropolitan area is one of the world's major concerns. However, since a large power plant can not be located around the city due to burden of economic cost, building power plant outside metropolitan and cities is necessary. Therefore, new power generation facilities are promoting policies to provide distributed generator(DG) with a small capacity relatively near the metropolitan. When the DG (photovoltaic, wind farm, etc.) is connected with the grid using medium voltage direct current (MVDC) system, voltage sourced converter(VSC) should supply reactive power to the grid, because of fault ride through(FRT) operation in grid fault. If the voltage drop is severe, the converter should be disconnected from the grid immediately without supplying the reactive power, resulting in a considerable economic loss. In general, superconducting fault current limiter(SFCL) is introduced as a measure to enhance FRT capability. In this paper, we use trigger type SFCL which protects superconducting element and reduces low voltage. On the other hand, the active power unbalance of the DC-link and the DC voltage rise due to the reactive power supply of the grid-side converter. The rise of the DC voltage causes the P (active power), Q (reactive power) control of the converter to deviate, causing malfunction and damage of the DC equipment. Therefore, the rise of the DC voltage must be prevented. In this paper, we consider the suppression the DC voltage rising caused by the FRT operation through the active power tracking control (APTC).

Adjustable frequency converters are widely used in modern automated asynchronous drives due to their high efficiency and high responsiveness control strategies. Control algorithms for frequency converters are divided into two main groups: constant frequency commutation and random frequency commutation. Research results on various commutation frequencies, conducted using Matlab/Simulink software, show that the use of random frequency commutation provides better efficiency by significantly reducing the amplitude of harmonic oscillations at different frequencies, with a reduction in switching losses in transistors. Currently, a converter with random frequency commutation is being researched and applied in the direct torque control system. The traditional direct control system, based on a two-level inverter, is widely used due to its simplicity and ease of implementation. However, this method results in the output current of the two-level converter, supplied to the motor stator, having many harmonic distortions, leading to strong torque fluctuations regardless of the rotation speed and ultimately causing additional losses in the stator windings and reducing the motor's lifespan. To enhance the efficiency of automated asynchronous drives, this article presents an algorithm for a direct control system based on a three-level NPC inverter using a PI speed regulator. The proposed algorithm's research is validated in the Matlab/Simulink environment. The research results show that in the absence of harmonic filtering, the stator current harmonic distortion coefficient is approximately 11%, and torque fluctuations are less than 5% of the resistive torque. The fluctuations between the two capacitors remain almost unchanged throughout the entire process.

The three-dimensional structure of Gulf of Mexico’s warm-core rings, detaching from the Loop Current, is investigated using satellite altimetry and a large set of ARGO float profiles. Reconstruction of the Loop Current rings (LCRs) vertical structure from sea surface height observations is made possible by the use of the gravest empirical modes method (GEM). The GEMs are transfer functions that associate a value of temperature and salinity for each variable pair {dynamic height;pressure}, and are computed by estimating an empirical relationship between dynamic height and the vertical thermohaline structure of the ocean. Between 1993 and 2021, 40 LCRs were detected in the altimetry and their three-dimensional thermohaline structure was reconstructed, as well as a number of dynamically relevant variables (geostrophic and cyclogeostrophic velocity, relative vorticity, potential vorticity, available potential energy and kinetic energy density etc.). The structure of a typical LCR was computed by fitting an analytical stream function to the LCRs dynamic height signature and reconstructing its vertical structure with the GEM. The total heat and salt contents and energy of each LCR were computed and their cumulative effect on the Gulf of Mexico’s heat, salt and energy balance is discussed. We show that LCRs have a dramatic impact on these balances and estimate that residual surface heat fluxes of -13 Wm−2 are necessary to compensate their heat input, while the fresh water outflow of the Mississippi river approximately compensates for their salt excess input. An average energy dissipation of O[10−10−10−9] Wkg−1 would be necessary to balance their energy input.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

To clarify the relationships among critical temperature, critical magnetic field, and critical current density, this paper describes many-body interactions of quantum magnetic fluxes (i.e., vortices) and calculates pinning-related critical current density. All calculations are analytically derived, without numerical or fitting methods. Afteralculating a magnetic flux quantum mass, we theoretically obtain the critical temperature in a many-body interaction scenario (which can be handled by our established method). We also derive the critical magnetic field and inherent critical current density at each critical temperature. Finally, we determine the pinning-related critical current density with self-fields. The relationships between the critical magnetic field and critical temperature, inherent critical current density and critical temperature, and pinning critical current density and temperature were consistent with experimental observations. From the critical current density and critical magnetic field, we clarified the magnetic field transition. It appears that a magnetic flux quantum collapses when the lattice of magnetic flux quanta melts. Our results, combined with our previously published papers, provide a comprehensive understanding of the transition points in high-T_c cuprates.

Eddy current testing can be used to interrogate steels but it is hampered by the lift-off distance of the sensor. Previously, the lift-off point of intersection (LOI) feature has been found for the pulsed eddy current (PEC) testing. In this paper, a lift-off invariant inductance (LII) feature is proposed for the multi-frequency eddy current (MEC) testing, which merely targets the ferromagnetic steels. That is, at a certain working frequency, the measured inductance signal is found nearly immune to the lift-off distance of the sensor. Such working frequency and inductance are termed as the lift-off invariant frequency (LIF) and LII. Through simulations and experimental measurements of different steels under the multi-frequency manner, the LII has been verified to be merely related to the sensor parameters and independent of different steels. By referring to the LIF of the test piece and using an iterative inverse solver, one of the steel properties (either the electrical conductivity or magnetic permeability) can be reconstructed with a high accuracy.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

Humpback whales perform long migrations from their breeding and nursing areas at low latitudes to feeding grounds at high latitudes. Nonetheless this strictly dichotomous paradigm of migration is challenged by accumulating examples of occasional or regular feeding in tropical or subtropical areas for several stocks worldwide. Here we report multiple lines of evidence of IWC ‘Stock G’ humpback whales feeding in coastal waters at low latitudes of the Southeast Pacific Ocean. Lunge-feeding behavior was observed in Ecuador, while both lunge- and trap-feeding in pursuit of Peruvian anchovy was documented in northern Chile. Five records of substantial defecation in a key breeding ground in Ecuador also demonstrates local foraging. In addition mark-recapture analysis of one individual feeding at high and mid latitudes of Chile suggested potential site fidelity to two foraging areas. Whether these behaviors are novel due to changes in prey distribution, intensifying competition for food from a growing humpback whale population, or rather reflect vastly increased research effort in a poorly studied region, remains unknown. Further research into the feeding ecology of 'Stock G' should help reveal historic and potentially novel feeding grounds, prey composition and precise migration paths.

In view of the preparation for a post-LHC collider, the high-energy physics (HEP) community started from 2010 to discuss various options, including the use of HTS for very high field dipoles. Therefore, a small program was set in Europe aiming at exploring the possibility of using HTS for accelerator quality magnets. Based on various EU funded programs, though at modest levels, has enabled the European community of accelerator magnets to start getting experience in HTS and addressing a few issues. The program was based on use of REBCO tapes to form 10 kA Roebel cables, to be used to wind small dipoles of 30-40 mm aperture in the 5 T range. The dipoles are designed to be later inserted in a background dipole field (in Nb3Sn), to reach eventually a field level in the 16-20 T range, beyond the reach of LTS. The program is currently underway: more than 1 km tape of high performance (Je &gt; 500 A/mm2 at 20 T, 4.2 K has been manufactured and characterized, various 30 m long Roebel cables have been assembled and validated up to 13 kA, a few dipoles have been wound and tested, reaching at present 4.5 T in stand-alone (while a dipole made from race track coils with no-bore exceeded 5 T using stacked tape cable) and a test in a background field is being organized.

Electromagnetic sensors have been used for inspecting small surface defects of metals. Based on the eddy-current thin-skin regime, a revised algorithm is proposed for a triple-coil drive-pickup eddy-current sensor scanning over long surface crack slots (10 mm) with different rotary angles. The method is validated by the voltage measurement of the designed EC sensor scanning over a benchmark (ferromagnetic) steel with surface defects of different depths and rotary angles. With an additional sensing coil for the designed EC sensor, the defect angle (or orientation) can be measured without spatially and coaxially rotating the excitation coil. By referring to the voltage change (due to the defect) diagram (voltage sum versus voltage different) of two sensing pairs, the rotary angle of the surface crack is retrieved with a maximum residual deviation of 3.5 %.

Two opposed p–n diodes are connected with another junction that causes cancellation of the electric field in the depletion layer of each diode by the field of the other diode. This derived quantum diode is called the A system. Another dual diode, constructed by the same process but with the p- and n-types positioned as duality, called the B system. When a bias voltage is applied between the A and B systems, Lorentz conservation imparts a momentum (i.e., a wave number) to the carriers in the absence of any internal voltage. Thus, a superconducting bias current density appears without the need for cooling. The reappearances of electron–hole pairs on the junction surfaces are assumed to be described by entire wavefunctions normalized by the band gap. Based on the bias superconducting current, NOT and NAND gates were constructed from the quantum diode systems. Numerical calculations revealed that the constant phases of the entire wavefunctions of the p-and n-types converged. Accordingly, it was clarified that Bose–Einstein condensation and the Meissner effect (described by the London equation) occurred in the quantum diode systems. Moreover, the systems exhibited rectification characteristics and a switching speed of the order of 10^-14 s. Combining this switching property with the large bias superconducting current (of the order of several V), we developed NOT and NAND gates with direct quantum correlations among many qubits, which are unaffected by random and thermal noises. These gates have memorization and initialization properties and are compatible with existing and accumulating programing algorithms. Moreover, when harvesting a divergent current output from these systems, the bias superconducting current and memorization property preserve the formed quantum correlations.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

Prestrained at 5% and 15% duplex stainless steel UNS S32750 specimens have been subjected to electropulsing treatments with current density of 100 A/mm2 and 200 A/mm2 and 100 and 500 pulses for each current density value. Corrosion tests, X-ray diffraction, microhardness and residual stresses were collected before and after the electropulsing treatments. Tensile tests were performed after the electropulsing treatments in order to compare the mechanical response to the reference tensile tests performed before the pulsing treatments. Increase in fracture strain was observed after the pulsing treatment in comparison to the reference tensile tests. A decrease in microhardness was also observed after the electropulsing treatments for both degrees of prestrain. Electropulsing treatment almost eliminates the work-hardened state in the 5% prestrained specimens while partially recovered the 15% prestrained material increasing both uniform and fracture strain. The bulk temperature of the samples remained the same for all the duration of the treatments. The effect are to be addressed to a combined effect of the increase in atomic flux due to the electrical current and local joule heating in correspondence of crystal defects. Electropulsing treatment applied to metallic alloys is a promising technique to reduce the work hardening state without the need of annealing treatments in a dedicated furnace.

The purpose of this paper is to explore which financial performance indicators (FPIs) evaluate the level of supply chain capability (SCC) that explicitly touches all of the business functions and processes within and beyond the company. The authors investigated nine FPIs that were selected from the financial statements of 155 companies within nine industries. The authors find that suitable FPIs to measure SCC for shareholders’ value are return-on-assets (ROA), days-sales-outstanding (DSO), and current ratio (CR). This means that higher ROA, shortened DSO, and an appropriate level of CR could reach a sustainable supply chain. These results will help the industry to avert a major disruption in supply chain processes and activities using suitable financial performance indicators.

The characterization of thin-film solar cells is of huge importance for obtaining high open-circuit voltage and low recombination rates from the interfaces or within the bulk of the main materials. Among the many electrical characterization techniques, the two- and four-wire probe using the Cascade instrument is of interest since the resistance of the wires, and the electrical contacts can be excluded by the additional two wires in 4-wire probe configuration. In this paper, both two and four-point probes configuration are employed to characterize the CIGS chalcogenide thin-film solar cells. The two-wire probe has been used to measure the current-voltage characteristics of the cell which results in a huge internal resistance. Therefore, the four-wire connection is also used to eliminate the lead resistance to enhance the characterization’s accuracy. The load resistance in the two-wire probe diminishes the photogenerated current density at smaller voltage ranges. In contrast, the proposed four-wire probe collects more current at higher voltages due to enhanced carrier collection efficiency from contact electrodes. The current conduction mechanism is also identified at every voltage region represented by the value of the ideality factor of that voltage region. It is observed that a long time given to the charge collection results in increased current density at a higher voltage. According to the results and device characteristics, a novel double-diode model is suggested to extract the saturation current density, shunt and series resistances and the ideality factor of the cells. These cells are shown to be efficient in terms of low recombination at the interfaces and with lower series resistance as the quality of the materials is in its most possible conductive form. The measured internal resistance and saturation current density and ideality factor of the two measurement configuration is measured and compared.

We construct families of ground state representations of the U(1)-current net and of the Virasoro nets Vir_c with central charge c ≥ 1. We show that these representations are not covariant with respect to the original dilations, and those on the U(1)-current net are not solitonic. Furthermore, by going to the dual net of with respect to the ground state representations of Vir_c, one obtains possibly new family of Möbius covariant nets on S¹.

A computational methodology for the hydrodynamic analysis of horizontal axis marine current turbines is presented. The approach is based on a boundary integral equation method for inviscid flows originally developed for marine propellers and adapted here to describe the flow features that characterize hydrokinetic turbines. To this purpose, semi-analytical trailing wake and viscous-flow correction models are introduced. A validation study is performed by comparing hydrodynamic performance predictions with two experimental test cases and with results from other numerical models in the literature. The capability of the proposed methodology to correctly describe turbine thrust and power over a wide range of operating conditions is discussed. Viscosity effects associated to blade flow separation and stall are taken into account and predicted thrust and power are comparable with results of blade element methods that are largely used in the design of marine current turbines. The accuracy of numerical predictions tend to reduce in cases where turbine blades operate in off-design conditions.

A three-dimensional, unstructured grid, hydrodynamic and suspended-sediment transport model (i.e., SELFE-SED) was developed to simulate temporal and spatial variations of suspended sediment and was applied to the subtropical subalpine Tsuei-Feng Lake (TFL) of Taiwan. The model was validated with measured water level and suspended‑sediment concentration in 2009, 2010, and 2011. The overall model simulation results are in quantitative agreement with the observational data. The validated model was then applied to explore the most important parameter that affects the suspended-sediment concentration and to investigate the effect of wind stress on the mean current and suspended‑sediment distribution in this shallow lake. Modeling results of sensitivity analysis reveal that the settling velocity is a crucial parameter and erosion rate is less important in the suspended-sediment transport model. Remarkable lake circulation was found based on the strength of wind speed and wind direction. Strong wind would result in higher mean current in the top layer and suspended-sediment distribution in the top and bottom layers. This study demonstrated that the wind stress played a significant influence on mean circulation and suspended-sediment transport in a shallow lake.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

The presence of escaped fish in aquaculture facilities as a result of harsh meteorological conditions (more pressing in a face of climate change) requires a better understanding of these dynamical behaviour through vigilant monitoring and validated numerical models. In this context, data from strain, stress sensors as well as meteorological and current sensors installed at an aquaculture farm in the Region of Murcia (Spain) were collected, processed and analysed. Among them, first results about the relationship between load and currents sensors are presented. Due to the complexity of the time series, various analyses were conducted to examine their interrelation, encompassing regression analysis of raw data and data segmented into different time intervals. Through this analysis, it was observed that employing distinct time windows better elucidated the data variability. Furthermore, an optimal data window of 240 data was identified, demonstrating significantly improved explanatory power, with the coefficient of determination (R2) increasing by approximately 0.8 depending on the section. This pave the way for optimizing the monitoring features that must be carried out to relate cause-and-effect variables in the behaviour of these off-shore infrastructures.

This study focuses on the modification of ion-exchange membranes by incorporating phosphorylated dendrimer into sulfonated polytetrafluoroethylene membranes to enhance specific selectivity between mono-/divalent ions, using the Ca2+/Na+ pair as an example. The research employs mechanical, physico-chemical, and electrochemical analyses to explore the effects of P-H20 incorporation on membrane properties. Bulk modification significantly increases membrane selectivity towards calcium ions (specific permselectivity coefficient rises from 1.5 to 7.2), while maintaining the same level of the limiting current density. Other findings indicate that bulk modification significantly changes the transport-channel structure of the membrane and alters the mechanism of over-limiting mass transfer. The over-limiting current for the pristine membrane is mainly due to non-equilibrium electroconvection, while modified membranes actively participate in the water-splitting reaction, leading to the suppression of the electroconvection. Despite this drawback, the decrease of the over-limiting potential drop results in a decrease in specific energy consumption from 0.11 to 0.07 kWh/mol. In the under-limiting current mode, the specific energy consumption for all studied membranes remains within the same limits of 0.02-0.03 kWh/mol.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.

The functional and neurophysiological distinction between dorsal and ventral hippocampus affects also GABAergic inhibition. In line with his notion, ventral CA1 pyramidal cells displayed a more dynamic and effective response to inhibitory input compared to their dorsal counterparts. We posit that this difference is effected by the dorsal-ventral gradient of activin A, a member of the transforming growth factor-β family, which is increasingly recognized for its modulatory role in brain regions involved in cognitive functions and affective behavior. Lending credence to this hypothesis, we found that in slices from transgenic mice expressing a dominant-negative mutant of activin receptor IB (dnActRIB), inhibitory transmission was enhanced only in CA1 neurons of dorsal hippocampus, where basal activin A level is much higher than in ventral hippocampus. We next asked how a rise in endogenous activin A would affect GABAergic inhibition along the longitudinal axis of the hippocampus. We performed ex vivo recordings from wild type and dnActRIB mice after overnight exposure to an enriched environment (EE), which engenders a robust increase in activing A levels in both dorsal and ventral hippocampi. Compared to control mice from standard cages, the behaviorally induced surge in activin A produced a decline in ventral inhibition, an effect that was absent in slices from dnActRIB mice. Underscoring the essential role of activin in the EE-associated modulation of ventral inhibition, this effect was mimicked by acute application of recombinant activin A in control slices. In summary, both genetic and behavioral manipulations of activin receptor signaling affected the dorsal-ventral difference in synaptic inhibition, suggesting that activin A regulates the strength of GABAergic inhibition in a region-specific fashion.

Porous ferroelectric lead zirconate-titanate (PZT) films are a promising material for various electronics applications. This study focuses on understanding how structure-directing agent (polyvinylpyrrolidone) can change structure and electrical properties of porous PZT films prepared by chemical solution deposition. The films with various porosity up to ~ 40 vol.% and pore connectivity changing from 3-0 to 3-3 were prepared and studied by capacitance-voltage, dielectric hysteresis, transient current, photocurrent, and local current techniques. We have found that the linear decrease in the material volume in a porous film is not the only factor governing film properties. The key role in changing electrical properties plays the creation of new internal grain boundaries. This research expands the understanding of physical phenomena in porous ferroelectric films and may enable the development of new materials and devices.

In this paper, based on the pseudo-totem pole (PTP) circuit, a family of five-level PTP dual boost converters (PDBC) is proposed. Dual boost converter has some unique advantages such as no bridge arm shoot-through risk and no switch body diode reverse recovery problem, so that it has a good application prospect. Compared with conventional three-level PTP converters, PDBCs has higher power density, higher efficiency, and low voltage and current stress. The topological derivation process, working principle, modulation and strategy of the topology are analyzed firstly. Further, the number of power devices, the switches voltage and current stress of the proposed topology is analyzed. Finally, a representative five-level PDBC experimental prototype is designed with AC input 220V/50Hz, DC output 400V/1kW, and peak efficiency of 98.27%. The experimental results show that the five-level PDBC proposed in this paper has higher efficiency and verify the correctness of the topology.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Aphasia is one of the most socially disabling post-stroke deficits. Although traditional therapies have been shown to induce adequate clinical improvement, aphasic symptoms often persist. Therefore, new rehabilitation techniques which act as a substitute or as an adjunct to traditional approaches are urgently needed. The present review provides an overview of the efficacy and safety of the most innovative approaches which have been proposed over the last twenty years. First, we examined the effectiveness of the pharmacological approach, principally used as an adjunct to language therapy, reporting the mechanism of action of each single drug for the recovery of aphasia. Results are conflicting but promising. Secondly, we discussed the application of Virtual Reality (VR) which has been proved to be useful since it potentiates the ecological validity of the language therapy by using virtual contexts which simulate real-life everyday contexts. Finally, we focused on the use of Transcranial Direct Current Stimulation (tDCS), both discussing its applications at the cortical level and highlighting a new perspective, which considers the possibility to extend the use of tDCS over the motor regions. Although the review revels an extraordinary variability among the different studies, substantial agreement has been reached on some general principles, such as the necessity to consider tDCS only as an adjunct to traditional language therapy.

This paper presents a concise exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been developed and deployed to synthesize the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that in spite of the fact that analytical methods may involve fair amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods.

Using co-precipitation to synthesize (CeO2)0.95(Y2O3)0.05 (YDC) and solid reaction method to synthesize (CeO2)0.75(ZrO2)0.25 (ZDC), and the characterization for both crystal structure and micro-structure of the two materials was conducted with X-ray diffraction (XRD) and scanning electron microscope (SEM) methods. Prepare the YDC and ZDC based limited current O2 sensor by employing platinum pasting bonding method. Sensing characteristics of the sensor were obtained at different conditions and study on the impact of temperature, O2 concentration as well as water vapor pressure on the sensing characteristics had been conducted. XRD results show that the phase structure of both YDC and ZDC is cubic phase. SEM results show that both YDC and ZDC layers are dense layers, which are then qualified to be the composition materials of the sensor. This limited current O2 sensor shows good sensing performance and conforms to the Knudsen model. Log(IL•T) depends linearly on 1000/T with R2 of 0.9904, IL depends linearly on x(O2) with R2 of 0.9726 and sensing characteristics are not affected by p(H2O).

There have been several cases of large-scale wind generators (WGs) tripping off caused by untimely fault removing in recent years. Currently, the discoordination between the box-type transformer fuse protection (BTFP) and two-section collecting line current protection (CLCP) brings a security risk to wind farm. In order to ensure the selectivity, the first section (Sec-I) CLCP should be set a enough interval that is longer than the fuse melting time, and another interval is set for the Sec-II CLCP, which weakens the speed of the CLCP. When a fault occurs on the collecting line, there is no doubt that WGs cannot work too long in abnormal operation, which may cause WGs to be placed off the grid. For a power system with high penetration of wind power, large-scale WGs tripping off will cause a great power shortage, and affect the stability of the power system. The selectivity and sensitivity of the CLCP is analyzed in detail to make the CLCP speed better. Considering the fault ride-through ability of WGs, the fault clear time is an important factor to lead to large-scale WGs tripping off. Two main works are done in this paper. The first is to accelerate the speed of the Sec-I CLCP though reducing the protection zone. Another one is introduce the risk assessment module into the CLCP, which not only improve the speed of the CLCP but also ensure the safety of the wind farm during faults. According to the deference in trip-off causes of WGs, the matching functions are created to assess the trip-off risk of WGs on the spot. In the case of fault, the trip-off risk indicators of WGs are timely updated to data sharing center and open to the CLCPs. The set of risk indicators is divided into several subsets according to the risk range. The dynamic changes of the subsets during fault help to improved CLCP scheme. This scheme can accelerate protection speed based on the increasing risk of large-scale WGs tripping off in wind farms. Compared with traditional CLCP, this approach can make the CLCP combines selectivity and speed better based on the analysis of the ride- through ability of WGs.

Inherent in every Active Magnetic Bearing (AMB) are differences between the expected geometric axes and the actual magnetic axes due to a combination of discrepancies, including physical variation from manufacturing tolerances and misalignment from mechanical assembly, fringing and leakage effects, as well as variations in magnetic material properties within a single AMB. A method is presented here for locating the magnetic axes of an AMB that will facilitate the accurate characterization of the bearing air gaps for potential improvement in field tuning, performance analyses and certain shaft force measurement techniques. This paper presents an extension of the application of the bias current perturbation method for the determination of the magnetic center [4] to the determination of magnetic axes for the further development of accurate current-based force measurement techniques [1].

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

The design of a mixed-mode proportional-integral-derivative (PID) controller circuit using current-feedback operational amplifiers (CFOAs) as active components is proposed. With the same circuit topology, the proposed configuration of three CFOAs, four resistors, and two capacitors is capable of performing the PID controller in all four operation modes: namely voltage mode, trans-admittance mode, current mode, and trans-impedance mode. Numerous mathematical analyses are conducted to determine the controller performance under ideal and non-ideal conditions. Additionally, the mixed-mode second-order lowpass filter is suggested, and also used to examine the workability of the proposed mixed-mode PID controller in a feedback control structure. The proposed PID controller is implemented with the commercially available IC-type CFOA AD844, and the simulation results are presented to illustrate the functionality of the controller and its closed-loop control system.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

Optimizing input parameters not only improves production efficiency and processing quality but also plays a crucial role in the development of green manufacturing engineering practices. The aim of the present study is to conduct a comparative evaluation at cutting performance and machinability process during the turning of AISI 4340 steel under different cooling conditions. The study analyses cutting operations during turning using dry, minimum quantity lubrication (MQL), and nano-MQL. As control parameters in the experiments, three different cooling types, cutting speed (100, 150, 200 m/min), and feed rate (0.1, 0.15, 0.20 mm/rev) levels were applied. The experiment results present that the optimal output values are found as Vb=0.15 mm, Ra=0.81µm, 88.1 dB for sound intensity, and I=4.18 A for current. Moreover, variance analysis (ANOVA) was performed to determine the effects of input parameters on response values. Under dry, MQL, and nano-MQL processing conditions, parameters affecting tool wear, surface roughness, current by the motor shaft, and sound level were examined in detail, along with the chip morphology. The responses obtained were optimized according to the Taguchi S/N method. As a result of optimization, it was concluded that the optimum values for cutting conditions (A3B1C1) were nano-MQL cooling and V=100 m/min, f=0.1 mm/rev cutting. Last but not least, it was observed that there was a 13% improvement in tool wear, 7% in current, 9% in surface roughness, and 8% in sound intensity compared to the standard conditions. In conclusion, it was determined that nano-MQL and the lowest level of cutting and feed rate values provided the optimum results.

This paper presents a comprehensive evaluation of metal foam employment within polymer electrolyte fuel cells (PEFCs) and compares it with conventional serpentine channels from both experiment viewpoints and computational fluid dynamics simulation. The experiments are designed to study the effects of material, area density, compression ratio, and final thickness of metal foam. Additionally, the influence of housing plate material and relative humidity (RH) is also tested for the first time. The results reveal that at RH=75-100%, the best distributor design is nickel foam with a compression ratio of 70%, a final thickness of 0.5mm, and SS-304 housing plate, which delivers 3110 mA cm^-2 as limiting current density that is scarce in the literature. The PEFC with this foam distributor shows a 10% improvement in maximum power density and 45% in limiting current density compared to the serpentine channel case. While at RH=30%, the same foam flow field with a final thickness of 1mm is a superior option. The experiments also indicate that maximum power density increases by 23% as the compression ratio rises from 0 to 70%, while reducing final thickness from 1 to 0.5 mm causes a 19% enhancement in cell performance. Simulation results reveal that metal foam is more successful in evenly reactant distribution so that the average oxygen mass fraction at the cathode catalyst layer is increased by 38% in the metal foam case compared to the serpentine channel.

We communicate the theoretical results in the study of utilizing the quantum phenomena in optical current for quantum computation in the context of high precision voltage measurements. These results can be used around computation by quantum sampling and quantum communication as the basis for further research and physical implementations. We propose a Main Optical Setup (MOS) for such computation which allows to make a superstructure to implement specific computations and algorithms. To create MOS we used the nonlinear units (e.g., beta- barium borate crystal), arranged in series, powered with pulsed laser pump, and ended with the beam splitter to generate the output state of a number of entangled photon pairs. The computation is made by propagation of entanglement with beam splitters applied crossword and adjustable phase shifters that are tools for parameter steering. We show how to implement the series of cosine-based components on the example of two-component case. The results opens a broad area for future research in the area of building quantum optimizer using the quantum sampling methods and in the area of high precision temporal measurement of voltage, which is the important process for building high-fidelity devices.

Electromagnetic eddy current sensors are commonly used to identify and quantify the surface notches of metals. However, the unintentional tilt of eddy current sensors affects results of size profiling, particularly for the depth profiling. In this paper, based on the eddy current thin-skin regime, a revised algorithm has been proposed for the analytical voltage or impedance of a tilted driver–pickup eddy current sensor scanning across a long ideal notch. Considering the resolution of the measurement, the bespoke driver–pickup, also termed as transmitter-receiver (T-R) sensor is designed with a small mean radius of 1 mm. Besides, the T-R sensor is connected to the electromagnetic instrument and controlled by a scanning stage with high spatial travel resolution , with a limit of 0.2 μm and selected as 0.25 mm. Experiments have been out on the voltage imaging of an aluminium sheet with 7 machined long notches of different depths using T-R sensor under different tilt angles. By fitting the measured voltage (both real and imaginary part) with proposed analytical algorithms, the depth profiling of notches is less affected by the tilt angle of sensors. From the results, the depth of notches can be retrieved within a deviation of 10 % for tilt angles up to 60 degrees.

A new approach to fabricate TiNi surfaces combining the advantages of both monolithic and porous materials for implants is used in this work. New materials were obtained by depositing a porous TiNi powder onto monolithic TiNi plates followed by sintering at 1200°C. Then, further modification of the material surface with a high-current-pulsed electron beam (HCPEB) was carried out. Three materials obtained (one after sintering and two after subsequent beam treatment by 20 and 30 pulses, respectively) were studied by XRD, SEM, EDX, EIS methods, profilometry and OCP measurements. Structural and compositional changes caused by HCPEB treatment were investigated. Surface properties of the samples during their storage in saline for 10 days were studied and a model experiment with cell growth (MCF-7) was carried out for the sample unmodified with electron beam to detect cell appearance on different surface locations.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Our earlier work has tentatively shown that the hierarchy of fermion masses and mixing angles follows from the universal behavior of nonlinear dynamics. In this brief sequel we survey a similar scenario in which the Cabibbo angle arises from the nonlinear dynamics of charged-current interactions.

Wall–stabilized arcs dominated by nozzle–ablation are key elements of self–blast circuit breakers. In the present study, high–current arcs were investigated using a model circuit breaker (MCB) in CO2 as gas alternative to SF6 and in addition a long polytetrafluoroethylene nozzle under ambient conditions for stronger ablation. The assets of different methods for optical investigation were demonstrated, e.g. high-speed imaging with channel filters and optical emission spectroscopy. Particularly the phase near current zero (CZ) crossing was studied in two steps. In the first step using high-speed cameras, radial temperature profiles have been determined until 0.4 ms before CZ in the nozzle. Broad temperature profiles with a maximum of 9400 K have been obtained from analysis of fluorine lines. In the second step, the spectroscopic sensitivity was increased using an intensified CCD camera, allowing single-shot measurements until few microseconds before CZ in the MCB. Ionic carbon and atomic oxygen emission were analyzed using absolute intensities and normal maximum. The arc was constricted and the maximum temperature decreased from &gt;18000 K at 0.3 ms to about 11000 K at 0.010 ms before CZ. The arc plasma needs about 0.5-1.0 ms after both the ignition phase and the current zero crossing to be completely dominated by the ablated wall material.

Purpose: Dysarthria, a neurological injury of the motor component of the speech circuitry, is of common consequences of traumatic brain injury (TBI). Palilalia is a speech disorder characterized by involuntary repetition of words, phrases, or sentences. Based on the evidence supporting the effectiveness of transcranial direct current stimulation (tDCS) in some speech and language disorders, we hypothesized that using tDCS would enhances the effectiveness of speech therapy in a client with chronic dysarthria following TBI. Method: We applied the constructs of the “Be Clear” protocol, a relatively new approach in speech therapy in dysarthria, together with tDCS on a chronic subject who affected by dysarthria and palilalia after TBI. Since there was no research on the use of tDCS in such cases, regions of interest (ROIs) were identified based on deviant brain electrophysiological patterns in speech tasks and resting state compared with normal expected patterns using the Quantitative Electroencephalography (QEEG) analysis. Results: Measures of perceptual assessments of intelligibility, an important index in the assessment of dysarthria, ​​were superior to the primary protocol results immediately and 4 months after intervention. We did not find any factor other than the use of tDCS to justify this superiority. The percentage of repeated words, an index in palilalia assessment, had a remarkable improvement immediately after intervention but fell somewhat after 4 months. We justified this case with subcortical origins of palilalia. Conclusion: Our present case-based findings suggested that applying tDCS together with speech therapy may improve intelligibility in similar case profiles as compared to traditional speech therapy. To reconfirm the effectiveness of the above approach in cases with dysarthria following TBI, more investigation need to be pursued.

This paper presents a control algorithm for soft-switching series LC converters. The conventional voltage-to-voltage controller is split into a master and a slave controller. The master controller implements constant-current-constant-voltage (CCCV) control, required for demanding applications, i.e. lithium battery charging or laboratory power supplies. It defines the set-current for the open-loop current slave controller, which generates the PWM parameters. The power supply achieves fast large-signal responses, e.g. from 5 V to 24 V, where 95% of the target value is reached in less than 400 µs. The design is evaluated extensively in simulation and on a prototype. A consensus between simulation and measurement is achieved.

Tidal stream energy is a low carbon energy source. Tidal stream turbines operate in a turbulent environment, and the effect of the structure between the turbine and seabed on this environment is not fully understood. An experimental study using 1:72 scale models based on a commercial turbine design was carried out to study the support structure influence on turbulence intensity around turbine blades. The study was conducted using the wave-current tank at LABIMA, University of Florence. A realistic flow environment (ambient turbulent intensity = 11%) was established. Turbulence intensity was measured upstream and downstream of a turbine mounted on two different support structures (one resembling a commercial design, the other the same with an additional vertical element), in order to quantify any variation in turbulence and performance between the support structures. Turbine drive power was used to calculate power generation. Acoustic Doppler Velocimetry was used to record and calculate upstream and downstream turbulence intensity. In otherwise identical conditions, performance variation of only 4% was observed between two support structures. Turbulent intensity at 1, 3 and 5 blade diameters, both upstream and downstream, showed variation up to 21% between the two cases. The additional turbulent structures generated by the additional element of the second support structure appears to cause this effect, and the upstream propagation of turbulent intensity is believed to be permitted by surface waves. This result is significant for the prediction of turbine array performance.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

Maxwell’s equations are valid only for a stationary observation point, therefore, to adequately describe real processes so far we have had to move to a moving reference frame. This paper presents the equations of electrodynamics for the moving observation point, it is shown that plane and spherical electromagnetic waves are their solutions, while the spherical wave propagates only outward, which cannot be said about Maxwell’s equations. The fields of uniformly moving charges are also solutions of the equations. Now there is no need to move to a moving reference frame, to use four-dimensional space and covariant form of equations. The question of finding a universal form of the equations that allows a solution in the form of the field of an arbitrarily moving charge remains open. This raises the question of the existence of a two-parameter group of transformations of electromagnetic fields along with the known one-parameter group has been posed. The phenomena derived from the equations, which make an additional contribution to the phase overrun in the Aharonov-Bohm effect are considered. The equation of motion of a charged particle in an electromagnetic field without simplifying approximations is considered, which allows us to take into account the radiation effects. It is shown that the fields in a moving observation point depend on its velocity and acceleration. In particular, although in a constant uniform electric field a force qE acts on a motionless charged particle, but on the same motionless but not fixed particle the force 4/3qE acts already, because it has a nonzero acceleration and the electric field at this point is larger. As the speed increases, the field decreases, and when it reaches the speed of light, when the particle stops accelerating, the force again becomes equal to qE The principle of operation of an unconventional alternator in a constant electric field and its corresponding engine, as well as new types of direct and impulse current generators, predicted by the equations, are described.

Severe Acute Respiratory Syndrome Coronavirus 2(SARS-CoV-2) is the virus that caused COVID-19 around the world. The disease starts off as a flu-like symptom and then eventually spreads in the human body.Infections are easily transmitted from human to human which makes it more severe among individuals. SARS-CoV-2 virus is in the same family of viruses SARS and MERS.As of today, there is no approved vaccine that can cure COVID-19. However, potential treatments showing promising improvement results among affected COVID-19 patients. In this review, the effectiveness of the current treatments for COVID-19 has been explored.

Bioelectrocatalysis provides the intrinsic catalytic-functions of redox enzymes to non-specific electrode reactions and is the most important and basic concept for biosensors. This review starts by describing fundamental characteristics of bioelectrocatalytic reactions in mediated and direct electron transfer types from a theoretical viewpoint and summarizes amperometric biosensors based on multi-enzymatic cascades and for multi-analyte detection. The review also introduces prospective aspects of two new concepts of biosensors: mass-transfer-controlled (pseudo)steady-state amperometry at microelectrodes with enhanced enzymatic activity without calibration curves and potentiometric coulometry at enzyme/mediator-immobilized biosensors for absolute determination.

Various types of electroconductive additives were evaluated for high C-rate capability in an attempt to extend practical application of high-areal-capacity lithium–sulfur batteries that employ an aluminum-foam current collector. Carbon nanofibers (CNFs) were found to be the most effective additive, with the ability to attain a high-sulfur-loading of 40 mg cm−2. A CNF-containing cell exhibited gravimetric capacities of 1094 and 758 mAh gsulfur−1 (46.8 and 32.4 mAh cm−2) at 0.05 and 0.1 C-rate, respectively, in an ether-based electrolyte. Because a CNF-containing slurry exhibits low viscosity even at a high solid ratio, it could be filled into the aluminum foam. Additionally, a lithium–sulfur battery with high-sulfur-loading had an energy density of ~120 Wh kg−1, a value that was calculated from the weight of the components of the cathode, anode, current collectors, electrolyte, and separator. Assuming that the amount of electrolyte decreases and that the energy density of cells accumulate, a theoretical energy density of 522 Wh kg−1 was estimated. Moreover, it was found that even if a high-areal-capacity was achieved, the discharge capacity converged at a high C-rate, unless there was an improvement in ion diffusion in the bulk electrolyte. This is considered a limitation of sulfur cathodes with high-sulfur-loading.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

We report on ground-based measurements of the atmospheric electric field (Ez= -Potential Gradient (PG)) and current density (Jz) that were conducted at two locations in Israel. One is the Emilio Segre cosmic ray station located on Mt. Hermon (34.45 N, 2020 m AMSL) located in northern Israel near the Syrian-Lebanon border and at the other at the Wise astronomical observatory in the Negev desert highland plateau of southern Israel (31.18 N, 870 m AMSL). We searched for possible effects of strong, short-term solar events on the potential gradient and the vertical current density, as disruption to the Global Electric Circuit are often observed following strong solar events. The first case study (St. Patrick Day, 17 March 2015) was classified as the strongest event of 2015. The second case study (8 Sep 2017) was categorized as the strongest event of 2017 and one of the twenty strongest events on record to date. The results show that the electrical parameters measured at ground level at both stations were not affected during the two massive proton events and the ensuing geomagnetic storms. The magnetospheric shielding in lower latitudes is strong enough to shield against flux of energetic particles from solar events, obscuring any impact that may be noticeable above the local daily variations induced by local meteorological conditions (aerosol concentrations, clouds, high humidity, and wind speed) which were investigated as well.

Smart grids are seeing an increase in renewable energy and an enormous introduction of advanced power electronics, increasing the number of disturbance sources. This requires improving the accuracy of measurement systems capable of acquiring data for use in power system monitoring applications. Rogowski Coils (RCs) and Merging Units (MUs) are being widely deployed in controlling, metering, and monitoring of digital power systems. Because the performance of digital measurement devices has a direct influence on power measurement accuracy, it is critical to perform a laboratory calibration of these measurement instruments before they are installed in any project. To determine the magnitude and phase displacement errors of the RC+MU under normal and abnormal operating conditions, this article presents a comprehensive laboratory digital calibration system constructed from precise, readily available commercial products such as a fluxgate current transducer and a National Instrument. In addition, the analysis of measurement chain is affected by sources of uncertainty is discussed. The tests yield findings that are consistent with the relevant standards.

Theta oscillations generated in hippocampal (HPC) and cortical neuronal networks are involved in various aspects of brain function, including sensorimotor integration, movement planning, memory formation and attention. Disruptions of theta rhythms are present in individuals with various disorders, including epilepsy and Alzheimer’s disease. Theta rhythm generation involves a specific interplay between cellular (ionic) and network (synaptic) mechanisms. HCN channels are theta modulators, and several medications are known to enhance their activity. We investigated how different doses of lamotrigine (LTG), an HCN channel activator, and antiepileptic and neuroprotective agent, would affect hippocampal theta rhythms in acute HPC slices (in vitro) and anaesthetized rats (in vivo). Whole-cell patch clamp recordings revealed that LTG decreased GABAA-fast transmission in CA3 and CA1 cells, in vitro. In addition, LTG directly depressed CA3 and CA1 pyramidal neuron excitability. These effects were partially blocked by ZD 7288, a selective HCN blocker, and are consistent with decreased excitability associated with antiepileptic actions. Lamotrigine also depressed hippocampal theta oscillations in vitro, also consistent with its neuronal depressant effects. In contrast, it exerted an opposite, enhancing effect, on theta recorded in vivo. The contradictory in vivo and in vitro results indicate that LTG increases ascending theta activating medial septum/entorhinal synaptic inputs that over-power the depressant effects seen in hippocampal neurons. These results provide new insights into LTG actions and indicate an opportunity to develop more precise therapeutics for the treatment of dementias, memory disorders and epilepsy.

There is a growing use of High Voltage Direct Current (HVDC) globally due to the many advantages of Direct Current (DC) transmission systems over Alternating Current (AC) transmission, including enabling transmission over long distances, higher transmission capacity and efficiency. Moreover, HVDC systems can be a great enabler in the transition to a low carbon electrical power system which is an important objective in today’s society. The objectives of the paper are to give a comprehensive overview of HVDC technology, its development, and present status, and to discuss its salient features, limitations and applications.

Previously, a conductivity invariance phenomena (CIP) has been discovered – at a certain lift-off, the inductance change of the sensor due to a test sample is immune to conductivity variations, i.e. the inductance – lift-off curve passes through a common point at a certain lift-off, termed as conductivity invariance lift-off. However, this conductivity invariance lift-off is fixed for a particular sensor setup, which is not convenient for various sample conditions. In this paper, we propose using two parameters in the coil design – the horizontal and vertical distances between the transmitter and the receiver to control the conductivity invariance lift-off. The relationship between these two parameters and the conductivity invariance lift-off is investigated by simulation and experiments and it has been found that there is an approximate linear relationship between these two parameters and the conductivity invariance lift-off. This is useful for applications where the measurements have restrictions on lift-off, e.g. uneven coating thickness which limits the range of the lift-off of probe during the measurements. Therefore, based on this relationship, it can be easier to adjust the configuration of the probe for a better inspection of the test samples.

Recently, several research groups have reported on anomalous enhancement of the self-field critical currents, Ic(sf,T), at low temperatures in superconductor/Dirac-cone material/superconductor (S/DCM/S) junctions. Some papers attributed the enhancement to the low-energy Andreev bound states arising from winding of the electronic wave function around DCM. In this paper, Ic(sf,T) in S/DCM/S junctions have been analyzed by two approaches: modified Ambegaokar-Baratoff and ballistic Titov-Beenakker models. It is shown that the ballistic model is an inadequate tool to analyze experimental data from S/DCM/S junctions. The primary mechanism for limiting superconducting current in S/DCM/S junctions is different from the conventional view that the latter is the maximum value within the order parameter phase variation. Thus, there is a need to develop a new model for self-field critical currents in S/DCM/S systems.

JBIR-99 is a secondary metabolite of marine fungi that has been shown to possess strong antibiotic activity. An efficient approach using a combination of size exclusion chromatography with a Sephadex LH-20 and high-speed counter-current chromatography (HSCCC) has been successfully developed for the isolation and purification of a polyketide from the solid-state fermentation of Meyerozyma guilliermondii. The active compound was isolated with purity >95% by HSCCC using an optimized solvent system composed of petroleum ether–ethyl acetate– 95% ethanol–water (5:3:5:3, v/v/v/v) after size exclusion chromatography. This compound was successfully purified in the quantity of 68 mg from 120 mg of the crude extract. The structure of JBIR-99 was elucidated and assigned by 1D, 2D NMR spectroscopic, and positive HRESITOFMS. Moreover, the relative configuration of compound JBIR-99, displaying a quite complex multi-ring structure, is determined by X-ray crystallography for the first time. The purification method developed for JBIR-99 will facilitate the further investigation and development of this antibiotic agent as a lead compound. Furthermore, it is suggested that the combination of size exclusion chromatography and HSCCC could be more widely applied for the isolation and purification of polyketides from marine fungi.

The Doubly-Fed Induction Generator (DFIG) has significant features in comparison with Fixed Speed Wind Turbine (FSWT), which has popularized its application in power system. Due to partial rated back-to-back converters in the DFIG, Fault Ride-Through (FRT) capability improvement is one of the great subjects regarding new grid code requirements. To enhance the FRT capability of the DFIG, many studies have been carried out. Fault current limiting devices as one of the techniques are utilized to limit the current level and protect switches of the back-to-back converter from over-current damage. In this paper, a review is done based on fault current limiting characteristic of the proposed fault current limiting devices Therefore, Fault Current Limiters (FCLs) and Series Dynamic Braking Resistors (SDBRs) are mainly taken into account. Operation of all configurations including their advantages and disadvantages is explained. Impedance type and the fault current limiting devices’ location are two important factors, which significantly affect the DFIG behaviour in the fault condition. These two factors are basically studied by the simulation and their effects on the key parameters of the DFIG are investigated. Finally, future works in respect to the FCL application in the FRT improvement of the DFIG have also been discussed.

Master equations define the dynamics that govern the time evolution of various physical processes on lattices. In the continuum limit, master equations lead to Fokker-Planck partial differential equations that represent the dynamics of physical systems in continuous spaces. Over the last few decades, nonlinear Fokker-Planck equations have become very popular in condensed matter physics and in statistical physics. Numerical solutions of these equations require the use of discretization schemes. However, the discrete evolution equation obtained by the discretization of a Fokker-Planck partial differential equation depends on the specific discretization scheme. In general, the discretized form is different from the master equation that has generated the respective Fokker-Planck equation in the continuum limit. Therefore, the knowledge of the master equation associated with a given Fokker-Planck equation is extremely important for the correct numerical integration of the latter, since it provides a unique, physically motivated discretization scheme. This paper shows that the Kinetic Interaction Principle (KIP) that governs the particle kinetics of many body systems, introduced in [G. Kaniadakis, Physica A 296, 405 (2001)], univocally defines a very simple master equation that in the continuum limit yields the nonlinear Fokker-Planck equation in its most general form.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.