Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

The manuscript presents the optical properties of directly deposited films of gold nanoparticles (AuNPs) prepared by ultrasonic spray pyrolysis technology. Four samples were produced, with an AuNPs deposition time of 15 min, 30 min, 1h and 4h on the glass substrate. The morphological characterization of the deposited films showed that the size of the first deposited AuNPs is between 10 and 20 nm, while with a longer duration of the deposition process, larger clusters of AuNPs grow by coalescence and aggregation. The prepared layers were optically characterised with Ultraviolet–visible spectroscopy (UV-vis) and ellipsometry. The ellipsometric measurements showed an increasingly denser and thicker effective thickness of the AuNPs layers. The extinction spectra display a clear local surface plasmonic resonance (LSPR) signature (peak 520-540 nm), indicating the presence of isolated particles in all samples. For all AuNPs layers, the imaginary part of both ε// and ε⏊ is dominated by a central peak around 2.2 eV corresponding to the LSPR of isolated particles and a high-energy shoulder due to Au interband transitions. It is shown that, as the density of particles increases, the extinction cross section grows over the whole spectral range where measurements are taken. Thus response can be explained with an enhanced electromagnetic response among AuNPs, that can be connected to the increase of particle density but also by the formation of clusters and irregular structures.

Safe water is a global public health concern amid increasing scarcity and pollution. Bottled water production and consumption contribute to these problems. This study examines tap water consumption in Italy, assessing associated sociodemographic factors and related health outcomes such as obesity and self-perceived health status. Data from the Italian National Statistics Institute's "Aspects of daily life" survey (N=45,597) were analyzed. Covariates included education, age, gender, economic status, region, concerns about waste and climate change, consumption of carbonated drinks excluding water, alcohol consumption, consumption of vegetables, consumption of snacks, body mass index, and self-perceived health status. Bivariate analyses and mixed-effect logistic regression models explored the associations. People who drink tap water were 19,674 with a higher prevalence in people aged 45 to 59 old, people with a graduate/post-graduate degree diploma, with optimal economic resources, and concerned about waste production and climate change, coming from the North-East regions of Italy. Underweight people showed a higher prevalence of TW assumption as well as those who drink less than occasionally carbonated drinks, drink alcohol, consume vegetables more than once a day, and snacks less than once a week with a satisfying level perceived health status. Regressions showed that all age classes are less likely to drink tap water than people younger than 20 years old. The category with “inadequate” economic resources is more likely to consume tap water. Low educational classes show a low likelihood of consuming tap water as well as Islands. A concern about waste production and climate change is associated with an increased likelihood of assuming tap water. Tap water consumption was negatively associate with obesity but not with a satisfactory Self-perceived health status. Insights from this study can inform public health strategies.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

As a new plant slope protection technology, living stumps can effectively improve slope stability. The current study attemptes to investigate the mechanical characteristics of the root system of living stumps and their reinforcement mechanism on slopes by carrying out a three-dimensional living stump slope modeling test. Using ABS materials, a 3D model of a living elm stump was created by 3D printing and a slope model test was carried out. The reinforcement mechanism of the living stump was studied through a combination of model testing and numerical simulation. The results indicate that, due to the presence of living stumps in the lower and middle parts of the slope, the maximum shear stress area of the soil moved to a deeper direction. The stress state of the soil around the living stump was effectively improved due to the existence of the lateral root system.Living stumps in the lower part of the slope cross the potential sliding surface and transferred the soil shear stress gradually to the root system through root-soil interaction. Moreover, the tap roots and lateral roots of living stumps form a robust spatial structure that bears the shear stress of soil together, thus increasing the stability of the slope.

Due to the growth of tourism, mining and manufacturing, economy of the Hainan Island, southern China has swiftly expanded, but also poses a risk of soil pollution by mercury (Hg) due to the traffic and mineral processing. In order to investigate the characteristics of soil Hg pollution in the Hainan Island and assess the health risk, a total of 239 samples were gathered from five representative regions across the island. A vehicle-mounted potable mercury analyzer was used to measure the atmospheric Hg and soil Hg concentrations in the collected samples. The results indicate that the soil Hg concentration of the five sub-study areas exhibits notable fluctuations, which was found to be influenced by various factors, including wind direction, mining activities, and economic development conditions. The degree of Hg pollution was assessed using both the Single Pollution Index Method and the Geoaccumulation Index Method. The results showed that although nearly half of the sampling points were contaminated, the current soil Hg level does not pose a non-carcinogenic risk to human health.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

Floods are a common natural disaster whose severity in terms of duration, water resource volume, peak and accumulated rainfall-based damage are likely to differ significantly for different geographical regions. In this paper, we first propose a novel hourly flood index (SWRI24−hr−S), derived from normalising the existing 24-hourly water resources index (WRI24−hr−S) in literature, to monitor flash flood risks on an hourly scale. The proposed SWRI24−hr−S is adopted to identify a flood situation and derive its characteristics, such as the duration (D), volume (V) and peak (Q). The comprehensive result analysis establishes the practical utility of SWRI24−hr−S in identifying flood situations at seven study sites in Fiji between 2014 and 2018 and deriving their characteristics (i.e., D, V, and Q). Secondly, this study develops a vine copula-probabilistic risk analysis system that models the joint distribution of flood characteristics (i.e., D, V, and Q) to extract their joint exceedance probability for the seven study sites in Fiji, enabling probabilistic flood risk assessment. The vine copula approach, particularly suited to Fiji’s study sites, introduces a novel probabilistic framework for flood risk assessment. The results show moderate differences in the spatial patterns of joint exceedance probability of flood characteristics in different combination scenarios generated by the proposed vine copula approach. In the worst-case scenario, the probability of any flood event occurring where the flood volume, peak and duration are likely to exceed the 95th-quantile value (representing an extreme flood event) is found to be less than 5% for all study sites. The proposed hourly flood index and the vine copula approach can be feasible and cost-effective tools for flood risk monitoring and assessment. The methodologies proposed in this study can be applied to other data-scarce regions where only rainfall data is available, offering crucial information for flood risk monitoring, assessment, and the development of effective mitigation strategies.

Authorities and governmental bodies strongly emphasize the importance of residents preparing for natural disasters, particularly underscoring the significance of readiness for geophysical hazards like earthquakes. In this study, which represents comparative quantitative research, the levels and predictors of the impact on preparedness for earthquake-induced disasters in South-Eastern Europe countries such as Montenegro, North Macedonia, and Serbia are examined. Using the snowball sampling technique (online questionnaire), a survey of 1245 respondents (Montenegro (n = 400), North Macedonia (n = 345), and Serbia (n = 500) was conducted from February 2023 to February 2024. The paper is based on the central hypothesis that the most significant predictor of earthquake preparedness in Montenegro, North Macedonia, and Serbia is age, followed by gender and education. Multivariate regression analysis was used to determine the extent to which five scores of the subscales (household preparedness, community preparedness, disaster preparation, earthquake risk awareness, reinforced house) were associated with seventh demographic and socio-economic variables. In addition to the mentioned analysis, other statistical analyses such as T-test, one-way ANOVA analysis, and Pearson correlation were also utilized. The results indicate that age emerges as a predictor in various aspects of earthquake-induced disaster preparedness and awareness in most models, followed by education. These findings confirm the significance of respondents' age in determining levels of preparedness and earthquake awareness. Overall, in North Macedonia, respondents recorded the highest ratings (M = 3.52) for household preparedness for earthquakes, compared to Montenegro (M = 2.98) and Serbia (M = 3.26), where the lowest ratings were recorded. Research findings, taking into account cultural characteristics, can serve as a basis for the development of targeted interventions, strategies, policies, and programs aimed at improving the level of societal preparedness for earthquake-induced disasters.

Rubber compounds based on styrene-butadiene rubber, ethylene-propylene-diene-monomer rubber and the combinations of both rubbers were cured with different sulfur and peroxide curing systems. In sulfur curing systems, two type of accelerators, namely N-cyclohexyl-2-benzothiazole sulfenamide, tetramethylthiuram disulfide and combinations of both accelerators were used. In peroxide curing systems, dicumyl peroxide, and combination of dicumyl peroxide with zinc diacrylate or zinc dimethacrylate, respectively were applied. The work was focused on investigation of the curing system composition as well as type of the rubber or rubbers combinations on curing process, cross-link density and physical-mechanical properties of vulcanizates. The dynamic-mechanical properties on the selected vulcanizates were examined, too. The result revealed correlation between the cross-link density and physical-mechanical properties. Similarly, there was recorded certain correlation between cross-linking degree and glass transition temperature. The tensile strength of vulcanizates based on rubbers combinations was higher when compared to that based on pure rubbers, which points out the fact that by rubbers combination, not only the features of both elastomers can be combined, but also improved tensile characteristics can be achieved. When compared to vulcanizates cured with dicumyl peroxide, materials cured with sulfur system exhibited higher tensile strength. By application of co-agents in peroxide vulcanization, the tensile strength overcame the tensile behavior of sulfur cured vulcanizates.

Dolichandrone spathacea is a rare and endangered semi-mangrove plant species with an extremely small population, naturally distributed only in Zhanjiang City and the east coast of Hainan Island, China. Regrettably, the present situation of the D. spathacea population in China has not yet been carefully investigated. In this study, we aim to evaluate the current resource status and population dynamic characteristics of D. spathacea on Hainan Island, China, in order to propose sustainable conservation and management strategies for future ecological restoration of its natural population. Our results show that D. spathacea on Hainan Island can be divided into four populations. All the D. spathacea populations present a state of overall dispersion, local concentration, and occasionally sporadic existence, and they exist in geographical isolation. The young, middle, and old D. spathacea plants account for 20.42%, 66.20%, and 13.38%, respectively, indicating that the overall age class of the D. spathacea population on Hainan Island belongs to a declining type. Furthermore, instead of temporal structure, we chose diameter at breast height (DBH) to establish a static life table, draw a population survival curve, and quantify the future development trend through population dynamic analysis and time-series prediction. These results directly point out that the D. spathacea population on Hainan Island is sensitive to external disturbances and possesses two main increases in mortality rate—namely, in its juvenile and mature stages—due to weak vitality, competition, and anthropogenic interferences, which are the most important reasons for its endangered status. Depending on the current conditions of the D. spathacea population, we should conserve and expand mature trees in situ, preserve their germplasm resources, rehabilitate their habitats to promote provenance restoration, and conduct artificial cultivation and spreading planting in order to realize the sustainable conservation and management of D. spathacea.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.

The worldwide competition to vaccinate against COVID-19 has highlighted the importance of immunization measures in containing the virus. Saudi Arabia, like the rest of the globe, must assess socio-demographic subtleties, chronic illnesses, vaccination effects, and public health policy implications as it navigates this complicated environment. This cross-sectional study examined Saudi COVID-19 vaccine in many ways. It examined the socio-demographic makeup of vaccine recipients, the prevalence of chronic conditions in this population, vaccine administration patterns, post-vaccination side effects, and vaccine-infection rates. A questionnaire-based online survey of 401 participants ensured gender, nationality, age, weight, and educational diversity. We analyzed vaccine manufacturer choice for each dosage, side effects after the first and second doses, and chronic diseases in the sample. Pfizer/BioNTech vaccines are preferred for all three doses, reflecting worldwide vaccination acceptance patterns. Side effects were not significantly different between vaccination kinds. Interestingly, immunization reduced infection rates, demonstrating the efficacy of COVID-19 vaccines. The data fills important information gaps and illuminates Saudi COVID-19 vaccination kinetics. These data support the global preference for mRNA vaccines, demonstrating the faith in this breakthrough technology. They also sponsor COVID-19 vaccine safety and effectiveness studies. The dramatic drop in infection rates among vaccinated people shows how vaccinations suppress the pandemic. These findings inform Saudi Arabia's immunization efforts. As booster doses become more common, long-term vaccination research is crucial. Vaccine reluctance, especially in certain demographics, must be addressed. Due to vaccines' protective potential, equitable vaccine distribution and large immunization programs are essential for herd immunity and pandemic management. This thorough cross-sectional study helps policymakers and healthcare practitioners build successful and inclusive COVID-19 immunization regimens in Saudi Arabia.

Background: COVID-19 has impacted Indian engineering institutions (EIs) enormously. It has tightened its knot around EIs that forced their previous half-shut shades completely down to prevent the risk of spreading COVID-19. In such a situation, fetching new enrollments on EI campuses is a difficult and challenging task, as students’ behavior and family preferences have changed drastically due to mental stress and emotions attached to them. Historically, during crisis situations, institutions have struggled to return to the normal track. Consequently, it becomes a prerequisite to examine the choice characteristics influencing the selection of EI during the COVID-19 pandemic to make it ‘normal’ for ‘new’ enrollments. The purpose of this study is to critically examine choice characteristics that affect students’ choice for EI and consequently to explore relationships between institutions’ characteristics and the suitability of EI during the COVID-19 pandemic across students’ characteristics. Quantitative research, conducted through a self-reported survey composed of a closed-ended structured questionnaire, was purposefully incorporated into the students who recently were enrolled in EIs (batch years 2020-2021) belonging to the North Maharashtra region of India. Results:The findings of this study revealed dissimilarities across students’ characteristics regarding the suitability of EIs under pandemic conditions. Regression analysis revealed that EI characteristics such as proximity, image and reputation, quality education and curriculum delivery have significantly contributed to suitability under COVID-19. At the micro level, multiple relationships were noted between EI characteristics and the suitability of EI under the pandemic across students’ characteristics. Conclusion:Bringing ‘normality’ to ‘new’ enrollments totally depends on EI’s resilience in meeting the needs of diversity in the COVID-19 pandemic situation, which repositions themselves to govern student-centric strategies instituted for the overall suitability of EI under pandemic conditions. The study has successfully demonstrated how choice characteristics can be executed to regulate the ‘suitability’ of EI under the COVID-19 pandemic for the inclusion of diversity. It is useful for policy makers and academicians to reposition EIs that fetch diversity during the pandemic. This study is the first to provide insights into the performance of choice characteristics and their relationship with the suitability of EIs under a pandemic and can be a yardstick in administering new enrollments.

Globally, workplace stress and anxiety are at an all-time high, with 42% of employees experiencing daily work-related stress and anxiety. Drawing from workplace anxiety (WA) theory (Cheng & McCarthy, 2018), we advance a model that considers four job demands – role ambiguity, work overload, job insecurity, and work-home conflict – as sources of daily WA, and in turn the downstream effects of WA on psychological capital (PsyCap). Our model posits gender as a moderator of the association between job demands and WA, and digital technology characteristics as moderators of the association between WA and PsyCap. We tested our predictions on a sample of 162 South African employees. Consistent with our predictions, we found positive effects of job demands on WA, with the relationship being stronger for females. Contrary to expectations, we found positive effects of WA on PsyCap, suggesting an adaptive function of WA. Perceived ease of use of digital technology moderated the association between WA and PsyCap, such that the association was strong at higher levels of perceived ease of use. This research advances our understanding of the sources of WA, the adaptive function of WA, and predictors of PsyCap. Broadly, our study adds to understanding emotions’ impact on workplace behavior.

Polarimetric features extracted from polarimetric synthetic aperture radar (PolSAR) images contain abundant scattering information of objects. Utilizing this information for PolSAR image classification can improve accuracy and enhance object monitoring. Although significant progress has been achieved in related research, there are still issues such as insufficient utilization of polarimetric information and features. In this paper, a deep learning classification method based on polarimetric channel power features for PolSAR is proposed. The distinctive characteristic of this method is that the polarimetric features inputted into the deep learning network are the power values of polarimetric channels, where these channels are treated equivalently and contain complete polarimetric information. In terms of experimental comparative study, besides polarimetric power combinations, three different data input schemes were employed as data for the input end of the convolutional neural network (CNN), taking into account existing research. The neural networks utilizes the extracted polarimetric features to classify images, and the classification accuracy analysis is employed to compare the strengths and weaknesses of different input schemes. It is worth mentioning that the polarized characteristics of the data input scheme mentioned in this article have been derived through rigorous mathematical deduction, and each polarimetric feature has clear physical meaning. By testing different data input schemes on the Gaofen-3 (GF-3) PolSAR image, the experimental results show that the method proposed in this article outperforms existing methods and can improve the accuracy of classification to a certain extent, validating the effectiveness of this method in large-scale area classification.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

The Planetary Roller Screw Mechanisms (PRSMs), alongside Ball Screw Mechanisms (BSMs) and Electromechanical Actuators (EMAs), occupies a pivotal role in advancing the precision and efficiency of various industrial applications, including aerospace, automotive, and high-precision machining tools. Despite their critical advantages such as high load capacity, superior precision, and extended lifespan, the deployment of PRSMs in complex operational conditions reveals a landscape rife with challenges and opportunities for further research. This comprehensive review endeavors to dissect the multifaceted aspects of PRSMs, focusing on their mechanics and dynamics, tribology and thermal behavior, and the paramount importance of reliability and condition monitoring. By synthesizing current research findings, this paper highlights the significant advancements in understanding the static and dynamic characteristics of PRSMs, the intricate interplay between lubrication conditions and wear mechanisms, and the critical role of thermal effects on operational performance. Moreover, it delves into the dynamic models that address the impact of manufacturing imperfections, such as waviness and defects, on the reliability of these mechanisms. Despite the strides made, the review identifies critical gaps in the existing literature, particularly under conditions of extreme temperatures, large deformations, and multifaceted loads, advocating for a holistic approach to research. By proposing integrated thermo-mechanical models and emphasizing the need for empirical validations, this paper outlines a roadmap for future studies aimed at facilitating the development of more robust and reliable PRSMs, capable of meeting the demands of complex operational scenarios and advancing the field of high-precision applications in aerospace, robotics, and beyond.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

Abstract: To explore the interrelationship between groundwater microbial communities and hydrochemical characteristics in Mancheng district, Baoding city, samples from karst groundwater and porous groundwater were collected respectively. The hydrochemical analysis and 16s RNA gene V4-V5 region sequencing method were used to detail the water environmental characteristics and microbial community distribution pattern in the study area. The hydrochemical results reveal significant differences in major ion contents and other hydrochemical indices between karst water and porous water. Microbial community analysis demonstrates that Proteobacteria, Actinobacteria, and Firmicutes are the dominant taxa in both types of water bodies, but their proportions vary significantly in different water bodies. The difference in microbial communities between karst water and porous water reflects the influence of environmental factors such as ion concentration and pH on microbial distribution. Redundancy analysis (RDA) indicates significant associations between microbial community composition and environmental factors in both types of groundwater environments. Studying the distribution pattern of microbial communities and the connection with environmental factors in two types of groundwater provides important basis for interpreting the functional roles of microbes in groundwater ecosystems.

Background Frequent presenters (FPs) define a group of individual who visit hospital emergency depart-ment (ED) frequently for urgent care. Many among the group present with main diagnosis of mental health conditions. This group of individual tend to use ED resources disproportionally and significantly affect overall healthcare outcome. No previous reviews have examined the profiles of FPs with mental health conditions. Aims This study aims to identify the key socio-demographic and clinical characteristics of patients who frequently present to ED with mental health primary diagnosis by performing systemic review from existing literature. Method PRISMA guideline was used. PubMed, PsycINFO, Scopus and Web of Science (WOS) were searched in May 2023. A manual search on reference list of included articles were conducted at same time. Covidence was used to perform extraction and screening, completed by two authors independently. Inclusion and exclusion criteria were defined. Results The abstracts of 3341 non-duplicate articles were screened with 40 full texts assessed for eligi-bility. 20 studies were included from 2004-2022 conducted in 6 countries with total patient number of 25688 (52% male, 48% female, mean age 40.7 years old). 27% were unemployed, 20% married, 41% homeless, and 17% had tertiary or above education. 44% had history of substance abuse or alcohol dependence. Top 3 diagnosis are found to be anxiety disorders (44%), depressive disorders (39%) and schizophrenia spectrum and other psychotic disorders (33%). Conclusion On average, FPs are middle aged and equally prevalent in both gender. Current data lacks rep-resentation for gender diverse group. They are significantly associated with high rate of unem-ployment, homelessness, lower than average education level, and being single. Anxiety disor-der, depressive disorder, and schizophrenia spectrum disorders are the most common clinical diagnosis associated with the group.

In China, there is an increasing need for greater genetic diversity in maize (Zea mays L.) germplasm and hybrids appropriate for mechanical harvesting. In order to test and distinguish American maize inbred lines with exceptional combining ability, four Chinese maize inbred lines (Chang7-2, Zheng 58, four-144 and four-287) were used to judge the combining ability and heterosis of 16 USA inbred lines by a NCII genetic mating method. The results showed that among the American inbred lines, 6M502A, LH208, NL001, LH212Ht, PHW51, FBLA and LH181 expressed good GCA for yield characteristics; while RS710, PHP76, FBLA, and PHJ89 showed excellent GCA for machine harvesting characteristics. Five hybrids (NL001 × Chang7-2, LH212Ht × Chang7-2, FBLA × four-144, LH181 × four-287, PHK93 × four-287) had better SCA values for yield characteristics, at 1.69, 1.07, 1.48, 1.84 and 1.05, respectively; while NL001 × Chang 7-2, 6M502A × Chang7-2, LH212Ht × Chang7-2, LH181 × four-287, PHW51 × Chang7-2 had better TCA values for yield characteristics, at 3.03, 2.80, 2.41, 2.19 and 1.91, respectively; NL001 × Chang7-2, 6M502A × Chang7-2, LH212Ht × Chang7-2, LH181 × four-287, PHW51 × Chang7-2 showed excellent Control Heterosis values, with 21.48%, 19.64%, 15.93%, 14.05% and 11.60% increases, respectively, compared to the check and potential for future utilization in Inner Mongolian corn production.

The concepts of fractional calculus and the related techniques have been gaining momentum in circuit system fields, and an increasing body of evidence suggests that fractional-order characteristics are widely distributed in electronic components. In this paper, we consider the fractional characteristics of non-solid aluminum electrolytic capacitors and focus on the nonlinear dynamic characteristics of peak-current-mode controlled (PCMC) dc-dc boost converters with such components. In the work, we establish a piecewise smooth non-commensurate fractional-order model to describe the converter, in which the fractional-order equivalent impedance model of capacitors is adopted and the detailed control loop is considered. In order to analyze the converter, we use the fractional Adams-Bashforth-Moulton typed method (F-ABM) and stroboscopic map technique to obtain the time-domain solutions and the bifurcation diagram. The results of bifurcation diagrams indicate that, with the change of different parameters, the converter enters chaotic state through period doubling bifurcation. In order to provide empirical evidence for the nonlinear dynamic analysis, we consider both circuit-level simulation and experiments in the work, the results of which further confirm the results of theoretical analysis.

The unique qualities of areas with natural landscape features help provide sustainability. Moreover, their different vegetation covers and ecosystems contribute to the preservation of their visual attraction. In recent years, the demand for natural areas has not only been seen at a recreational level, but has also become associated with the conservation and sustainability of those areas. Although the concept of sustainability is expressed from an ecological point of view, studies indicate that the visual aspect is also an important component. Thus, in this study, a visual quality assessment was carried out which considered both objective and subjective evaluations of different habitat types. Efteni lake-wetland and Melen Ağzı dunes (Düzce), Anzer, Ayder, and Çat Düzü highlands (Rize), and Sultanmurat and Taşli highlands (Trabzon) were selected as the study areas. A visual quality analysis was conducted with a total of 43 participants (23 students, 16 local inhabitants and four lecturers) in order establish their preferences in areas with different landscape characteristics. For the determination of the visual qualifications of these areas, a total of 24 photographs showing typical images representing each habitat type (three photographs for each) were employed. Taking perceptual parameters into consideration, assessment of visual quality was made according to the points given to each photo by the participants. Consequently, differences in visual quality were found to be influenced by the demographic status of the participants, differences in habitat types, recreational trends and the conservation status of the habitats.

This paper examines the effect of the aggregate type on concrete strength and more specifically how the petrographic characteristics of various aggregate rocks as well as their physico-mechanical properties influences the durability of C 25/30 strength class concrete. The studied aggregate rocks are derived from Veria-Naousa and Edessa ophiolitic complexes as well as granodiorite and albitite rocks from their surrounding areas in central Macedonia (Greece). Concretes are produced with constant volume proportions, workability, mixing and curing conditions using different sizes of each aggregate type. Aggregates were mixed both in dry and water saturated states in concretes. Six different types of aggregates were examined and classified in three district groups according to their physicomechanical properties, petrographic characteristics and surface texture. The classification in groups after the concrete compressive strength test verified the initial classification in the same three groups. Group I (ultramafic rocks) presents the lowest concrete strengths, depending on their high alteration degree and the low mechanical properties of ultramafic aggregates. Group II (mafic rocks and granodiorite) presents a wide range of concrete strengths, depending on different petrographic characteristics and mechanical properties. Group III (albite rocks) presents the highest concrete strengths, depending on their lowest alteration degree and their highest mechanical properties. Therefore mineralogy and microstructure of the coarse aggregates affects the final strength of the concrete specimens.

The Smart Angel connected medical device allows ambulatory surgery patients to monitor their health by taking their own blood pressure and oxygen levels and by answering a health questionnaire from home. This preventive device must necessarily be "usable" by patients with different profiles. The objective of this article is, therefore, to better understand the links between certain characteristics of potential patients and usability. We conducted an experimental study involving thirty-six participants, investigating the effects of four patient characteristics (i.e. age, education, technophilia and health literacy) on usability measured in terms of effectiveness, efficiency, and satisfaction. The results show a moderate correlation between age, health literacy and usability. However, there is a weak correlation between technophilia and usability and no relationship between the level of education and usability. This study provides theoretical insights into the effects of user characteristics by means of personas in usability (ISO 9241-11).

Heavy metal pollution in the aquatic water bodies via the discharge of various toxic heavy metals from industrial effluents has been a major concern in the present era. Various physical and chemical processes are available to solve this problem of heavy metal pollution. Biosorption is considered as a potential alternative for the removal of heavy metals from waste waters as compared to other conventional processes. In the present work, biosorption of Cu(II), Cr(VI), Pb(II) and Zn(II) ions from aqueous solutions was carried out by using peels of Citrus aurantifolia. The peels were found to be efficient in the biosorption of all four metal ions under study. The biosorption process was found to be influenced by factors like contact time, temperature, pH, turbidity as well as biosorbent dose. Further, the change in characteristics of Citrus aurantifolia after biosorption process was studied by using E-SEM, EDAX and FT-IR analysis. The adsorption isotherm studies revealed that Freundlich isotherm model showed better fir to experimental data as compared to Langmuir isotherm model. The results were found to be significant statistically. The regeneration of biosorbent was carried out by desorption study by using certain eluents.

Humans are exposed to the environmental pollutants 2, 4-dichlorophenol (2, 4-DCP) and 2, 5-dichlorophenol (2, 5-DCP) through air, use of water and consuming products. In this study, we evaluated the urinary concentrations of these compounds in Korean people from the age of 18 to 69 years by making use of the data from the Korean National Human Biomonitoring Survey that was completed in 2009. Of 1,865 representative Koreans, 63.4% and 97.9% were found to have concentrations of 2, 4-DCP and 2, 5-DCP > 0.05 μg/L (limit of detection) in their urine. The geometric mean urinary concentrations were 0.14 μg/L (confidence interval of 95% = 0.13–0.16) and 0.44 μg/L (confidence interval = 0.41–0.48), respectively. It was fond that the adjusted proportional changes in 2, 4-DCP concentrations were significantly associated with body mass index, whereas those of 2, 5-DCP concentrations were influenced by place of residence. From these findings, it is evident that most adults in Korea have levels of 2, 4-DCP and 2, 5-DCP that are detectable in their urine and burden of these compounds on their bodies varies depending on numerous demographic factors.

With the rapid development of cities in northwest China, there has been an increasing focus on groundwater pollution in plateau cities, specifically the common occurrence of nitrate pollution. The special climatic, geological, and geomorphological characteristics of plateau and river valley cities contribute to distinct groundwater chemical characteristics. Therefore, the formation and evolution process of groundwater nitrate contamination differs from that of plain cities. To explore these issues, we conducted an analysis of eight major ions in various groups of water samples from rivers, springs, and groundwater in Haidong. By utilizing factor analysis and correlation analysis, we were able to identify the characteristics and formation of groundwater chemistry and nitrate pollution in Haidong. Our findings reveal that the chemical characteristics of groundwater in Haidong are primarily controlled by rock weathering, mineral dissolution, and evaporation, leading to the formation of highly mineralized groundwater. Additionally, the excessive nitrate content in certain areas is a result of domestic sewage discharge and agricultural fertilizer use, exceeding Chinese drinking water health standards. Furthermore, for cities located in valleys, the geological structure significantly impacts the nitrate content of groundwater in different regions. Areas with obstructed groundwater flow tend to have higher nitrate levels, while regions with unobstructed groundwater experience lower nitrate concentrations. Notably, shallow groundxwater is more vulnerable to nitrate pollution compared to deep groundwater. This study holds great significance in understanding the chemical characteristics of groundwater and the formation and evolution of nitrate pollution in highland river valley cities.

What would compel a composer to set the same poem twice? Ludwig van Beethoven first set the text of Christoph Tiedge’s “An Die Hoffnung” (to Hope) between 1804 and 1805, and would later set the poem again, using even more of the text in 1815. While seeking context clues from what is known of his biography is crucial, another avenue of study lies within the pieces themselves. Through the study of key characteristics during Beethoven’s lifetime in addition to what biographical information we know, we can infer Beethoven’s intentions with each setting of the text and how this reflects his changing relationship to the text of “An Die Hoffnung”.

This study investigated the anatomical characteristics and pulp quality of tapped Styrax sumatrana wood to facilitate its further utilization. The transverse surface of the tapped S. sumatrana was light or greyish brown in the sapwood and reddish brown in the heartwood. The resin canals of the tapped wood were formed along the growth rings at the boundaries between the heartwood and sapwood. Furthermore, microscopic analyses revealed an irregular outline and rounded epithelial cells at the edges of the intercellular traumatic resin canal (TC). Approximately 8–16 epithelial cells surrounded the resin canals. The fibers in the tapped S. sumatrana were generally thin-walled, whereas those near the TC were thick-walled. Moreover, S. sumatrana were diffuse-porous and exhibited intermediately distinct or indistinct growth ring boundaries. The vessels were mainly in radial multiples and clusters of 3–5. In addition, they showed a diagonal-to-radial pattern arrangement and a few tangential bands. Deposits were observed in some vessels in the tapped part but were absent in the untapped part. The fiber length of the tapped S. sumatrana wood was classified as moderate to extensive and categorized as 2nd grade pulp quality. Finally, the cell walls were classified as thin to moderate.

The goal of our article was to systematize studies that investigated the impact of living conditions in large national regions on individual alcohol consumption. We sought publications on the research topic in PubMed, Google Scholar, OpenGrey, Crossref and eLibrary databases from the moment they were created until December 31, 2021. After removal of duplicates and unsuitable publications, and full-text review of remaining published sources, the final sample included 81 publications. The majority of ultimately selected papers were published after 2010, represented the United States of America, and considered samples of children and youths, either the younger population or the general adult population. High quality was characteristic for 19 studies, while satisfactory quality was exhibited by 46 publications. The most consistent associations with individual alcohol consumption were revealed for the legislative environment (especially for integral scales and indices), alcohol pricing policy, the prevalence of alcohol consumption and binge drinking in the population, and unemployment rate. Among the shortcomings of the reviewed articles, we should mention the prevailing assessment of the impact of only one type of regional characteristics, as well as the lack of studies analyzing the interaction of environmental influence at the territorial level of different scales. Protocol PROSPERO CRD42021234874.

Stratocumulus (Sc) is the most common cloud type in China. Sc clouds may or may not be accompanied by various types of precipitation that are representative of different macro- and microphysical characteristics. The finely resolved CloudSat data products are used in this study to quantitatively investigate the macro- and microphysical characteristics of precipitating and non-precipitating Sc (PS and NPS, respectively) clouds over Eastern China (EC). Based on statistical information extracted from the CloudSat data, Sc clouds are highly likely to occur alone, in association with liquid precipitation, or in association with drizzle over 25.65% of EC. The cloud bases of NPS clouds are higher than those of PS clouds, although the latter display higher cloud top heights and thicker cloud thicknesses. The spatial distributions of microphysical characteristics differ between PS and NPS clouds. The magnitudes of microphysical characteristics in NPS clouds are relatively small and decrease with height, whereas the magnitudes of microphysical characteristics in PS clouds are relatively large and peak in response to certain circulation patterns and over certain terrain. The variations in microphysical characteristics in Sc clouds with height and contoured frequency by altitude diagrams (CFADs) of radar reflectivity may indicate that different microphysical processes operate in PS and NPS clouds. In NPS clouds, hydrometeor particles accumulate by coalescence as they rise; once the particles are too large to be supported by updrafts, the cloud droplets form raindrops. In PS clouds, raindrops increase continuously in size via collision-coalescence processes as they fall. The levels between 2.5 and 3.0 km represent the space where particles grow most rapidly. Particles are affected by updrafts and accumulate at levels between 2.5 and 1.0 km as height decreases.

The physical properties of coal reservoirs are the main restrictions to exploration and development of CBM. The study of the physical characteristics of coal reservoirs and their controlling factors is of great significance to the safe and efficient development and utilization of CBM resources in the mining area. The Pingdingshan No. 10 coal mine was chosen for this study because of its better gas production effect at the test wells. The reservoir properties of the main coal seams of the No. 10 coal mine were tested and analyzed to comprehensively evaluate the reservoir properties. The results indicate that (1) The gas content and methane purity of the No. 4 coal seam are significantly higher than the No. 2 seam, and therefore they have better development potential than the No. 2 seam; (2) The average adsorption time of the No. 2 coal seam is less than that of the No. 4 seam, making it easier to reach the peak production capacity of CBM wells in the short term, but is not conducive to long-term stable production of CBM. The Langmuir volume of the No. 2 coal seam samples was significantly greater than for the No. 4 coal seam; however, the No. 4 coal seam contains about three times the amount of gas in the No. 2 seam; (3) All three coal seams have high porosity, which is favorable for large amounts of CBM adsorption and storage. Micropores predominate, transitional pores are less frequent, and a few mesopores occur; macropores are the least common. Samples from the No. 4 seam contained the highest proportion of micropores; (4) Organic pores were common in the all coal samples, with pore diameters not more than 30 µm, mainly concentrated between 50.5 and 1000 nm. Microfractures with aperture less than 70 nm were relatively frequent, mainly in the 50–65 nm range. A large number of the nanoscale microfractures were curved or jagged; (5) Fractures in the No. 2 and No. 4 coal seam samples with widths of 50 nm to 20 µm were more developed, and many were filled with kaolinite, quartz and other minerals; (6) The samples contained mostly layered silicate minerals (kaolinite), with hard granular minerals (quartz) next, and a very small quantity of iron-type minerals such as siderite and pyrite in dendritic form. The results of this study can provide a reference basis for the large-scale development and utilization of subsequent CBM wells.

Fresh water is valuable nonrenewable resource and plays an important role of maintaining economic and social development. Condisering its large population and consumption potential, water resources deficit will certainly impede basic industries sustainable development of China in the near future. Application of sewage irrigation, to some extent, was regarded as an alternative way to solve the problem of agricultural irrigation water shortage in some areas (such as North China). However, accompanied with extensive implementation of sewage irrigation, some problems on sewage irrigation in agriculture are gradually obvious, especially serious pollution and destruction for farmland. In this paper, the effects of sewage irrigation on soil physical (soil bulk density, soil resistance to penetration and field capacity), chemical (pH, soil organic matter, nitrogen, phosphrous, patassium, heavy metal and organic pollutants) and biological characteristics (soil microorganism and enzyme activities) of farmland in China were systematically reviewed on the base of the current utilization status of China’s farmland sewage irrigation and some feasible suggestions were put forward to the development prospect for the future. This review will be beneficial for promoting healthy development of sewage irrigation and providing theoretical support for reclamation and high efficiency of effluents in China.

Most malignant ovarian germ cell tumors (MOGTCs) have a very good prognosis and can be cured by chemotherapy, with yolk sac tumors (OYSTs) having the worse prognosis among MOGCTs. These tumors are rare and can benefit in the next future from specific therapeutic strategies after failure of platinum-based first-line and salvage regimens. In collaboration with EORTC SPECTA, we have developed a project to explore the molecular characteristics of OYST. The pilot part of the project was performed using retrospective samples and ten OYST patients including relapsed and disease free patients. The molecular analysis was performed using FoundationOne CDx. For each patient, the following variables are described in the molecular report provided by FMI (Fondation Medicine Incorporation): alteration type (SNV, deletion), actionable gene alteration, therapies approved in EU (patient's tumor type and other tumor types), tumor mutational burden (TMB) and microsatellite instability (MSI) status. A total of 10 patients with OYST diagnosed between 2007 and 2017 were analyzed. Four patients (40%) had a molecular alteration, according to the FMI test. A subset of three patients (33.3% of all patient) harbored targetable (KRAS, KIT, ARID1A) oncogenic mutations. Two patients at relapse harbored a targetable mutation. In this retrospective study, we were able to identify clinically relevant molecular alterations for all relapsed patients with molecular analysis. Dedicated studies are needed to demonstrate if they could benefit from specific therapeutic strategies after failure of platinum-based first-line and salvage regimens and if the presence of a molecular alteration could be linked to patients’ outcome.

Spirit of science is one of the important components of science education theory. It not only directly affects the level of science education, but also indirectly affects the selection, education and evaluation of scientific researchers, and the development of science and technology in a country or region. Although more than a century ago, the researchers began to discuss the topic of spirit of science. However, to date, the research of the definition, attribute, structural model and its characteristics of the spirit of science has not yet made a breakthrough. Based on the detailed literature review, the related theoretical analysis and the research of the structural model of the spirit of science, this paper puts forward the new definition, the attribute and the establishment of the structural model of the spirit of science, and analyzes the match the situation from new structural model of the spirit of science and the scientific nature published by the American Society for the Advancement of Science. The results of this study are of great significance for raising the level of scientific education and cultivating future scientific researchers, enhancing their motivation and skills in innovation in scientific research and promoting the development of future scientific undertakings.

In recent years, the economies of many countries of the world are in a situation of intense shock processes. The current situation urgently needs to change the economic paradigm in the near future, which objectively requires the development of new conceptual models. The purpose of the paper is to develop the basic theoretical provisions of a new macroeconomics based on impulse and jump processes. Research problems are the following: 1) to describe the main types of impulse and jump functions with examples from economic theory and practice; 2) to perform an analytical representation of impulse and jump functions; 3) to select macroeconomic characteristics for the analysis of rapidly changing processes in the economy; 4) to create models and mechanisms for predicting impulsive and abrupt changes in macroeconomics. The approaches to the development of macroeconomic theory and its methods proposed in the article are not associated with the use of evolutionary continuous functions, for example, power functions, which is typical for many canonical macroeconomic models. These approaches do not include management decisions to achieve optimal values of given target functions, which is typical for recursive macroeconomic models of dynamic programming. This article is about formulating the foundations of macroeconomic theory and its methods, which, with some degree of accuracy, could give a forecast about the impending possibility of abrupt changes (impulse, shock, jump, stepwise and others) in the macroeconomic situation. The research methodology is statistical analysis, special methods for studying impulse and jump processes developed by the author. As a result of the study, the main provisions of the macroeconomic theory based on rapid impulse and spasmodic changes were formulated, approaches were outlined for constructing the tools of this theory, problems and tasks for further research were identified.

Halloysite nanotubes (HNTs) are natural occurring mineral clay nanotubes that have excellent application potential in different fields. However, HNTs are heterogeneous in size, surface charge and formation of surfacial hydrogen bond, which lead to weak affinity and aggregation at a certain extent. It is very important to modify the HNTs’ surface to expand its applications. In this review, the structural characteristics, performance and the related applications of surface-modified HNTs are reviewed. We focus on the surface-modified variation of HNTs, the effects of surface modification on the materials and related applications in various regions. In addition, future prospects and the meaning of surface modification were also discussed in HNTs studies. This review provides a reference for the application of HNTs modifications in the field of new nanomaterials.

Demand for development of the convergence industry, research studies on electrical conductivity, thermal characteristics, semiconductors, motors, and batteries using special materials have come to the fore. Meanwhile, molybdenum (Mo) exhibits relatively small inorganic qualities, and the thermal conductivity rate is applied to various fields. In this study, in-depth characteristics were considered regarding the concentration of thermal characteristics, IR car terminal characteristics, and IR ve-hicles. This study calculated each phase temperature of the molybdenum sputtered specimens in the steady state according to the heat transfer theory. When the molybdenum-sputtered fabric’s metal layer pointed to the outside air, the heat transfer rate (Q) was high at 5748.3W, In contrast, if the molybdenum sputtered film’s metal layer of the pointed toward the heat source, the heat transfer rate (Q) was low at 187.1W. As a result of measuring the IR transmittance, the infrared transmit-tance of the molybdenum sputtering-treated sample was significantly reduced compared to the untreated sample. In the case of untreated samples, the transmittance ranged from 92.7 to 42.0%. When only the cross part was treated with molybdenum sputtering and the molybdenum surface was directed toward the IR irradiator, the IR transmittance was 66.8~0.7%. It is believed that the molybdenum sputtering polyamide samples produced in this study can be applied to multifunc-tional military wear, biosignal detection sensors, semiconductor products, batteries, etc., by utilizing excellent electrical properties, stealth functions, IR blocking properties, and lightness for infrared thermal imaging detectors.

In this paper, the main physicochemical characteristics and evolutionary laws of microbial community structure during the fermentation of aged vinegar were discussed, and the correlation between Cuqu and microorganisms and physicochemical characteristics during fermentation was explored. The results showed that there are significant differences in genera at different stages of fermentation, the main dominant bacteria in R1 are Bacillus, Lactobacillus, Aspergillus and Issatchenkia. At R2 fermentation stage, Lactobacillus, Acetobacter and Saccharomyces showed an upward trend and finally became absolute advantage bacteria. The main genus of bacteria at the end of overall fermentation is Aspergillus. Correlation analysis shows that in Cuqu, the bacterial genera that are significantly positively and negatively correlated with reducing sugars and amino acid nitrogen are the same, while the bacterial genera that are significantly positively and negatively correlated with pH and saccharification power are the same. During the fermentation process, pH, reducing sugar and saccharification ability are mainly positively correlated with bacterial genera. And research has found that during the fermentation process, the overall correlation between fungal communities and physicochemical characteristics is weaker compared to bacteria.

Carbon, which exists in large quantities on Earth, is a material with interesting properties, and many studies have been conducted since the past. In particular, nano-sized carbon allotropes are called carbon nanomaterials, and many studies are currently underway. Among them, carbon nanowall (CNW) is a structure in which graphene of sp2 bond is grown vertically, CNW have outstanding strength, can be highly electrically conducting or semiconducting, have a large specific surface area per unit mass. Electrical, chemical, physical properties of these CNW is modified by parameter such as surface density, height and thickness of it. Those have great effect on CNW and can be adjusted as growth interlayer. It was confirmed that the molybdenum disulfide (MoS2) interlayer synthesized by radio frequency (RF) magnetron sputtering altered the morphological characteristics such as the shaped edge of the CNW, the pores diameter and density. Through these studies, we confirmed the effect of MoS2 on the morphological characteristics of CNW. This opens the door to improving the performance of electrodes and devices.

Abstract. Indonesia has developed several superior soybean varieties. Each soybean variety has different physical and chemical properties that can affect processed products and soybean quality. The purpose of this study was to determine the physical, chemical, and functional properties of three superior early-maturing soybean varieties. The research was conducted in Maros, Indonesia in 2022 by planting the Dega-1, Grobogan, and Gepak Kuning varieties and repeated them 6 times. The yields of the three soybean varieties Dega-1, Grobogan, and Gepak Kuning were taken at 1 kg each and 3 repeated, then further analysis of chemical compounds is carried out in the laboratory. The results showed that for physical characteristics, the largest seed size was in Dega-1 (18.57 g per 100 seeds) and the smallest in Gepak Kuning (8.29 g). The highest bulk density of soybean seeds was in the Grobogan and Dega-1 varieties (0.79 kg per m3) and the lowest was in Gepak Kuning (0.77 kg per m3 ), and the lowest number of damaged seeds was in Dega-1 (6.67%) and the highest in Grobogan (11.33). %). Chemical characteristics, highest protein content in Gepak Kuning (39.72%) and lowest in Dega-1 (36.62%), lowest fat content in Dega-1 (12.63%) and highest in Gepak Kuning (14.49%), highest phosphorus content in Gepak Kuning (0.59%) and the lowest was in Grobogan (0.53%), the highest calcium content was in Gepak Kuning (0.40%), and the highest FFA value was in Dega-1 (0.93) and the lowest in Gepak Kuning (0.81). Based on physical properties, Dega-1 is the best compared to the other two soybeans. Meanwhile, based on the size of starch granules, Gepak Kuning gave the best results. For chemical characteristics, in general, GepakKuning has the best quality compared to Grobogan and Dega-1. It can be concluded that Gepak Kuning has the most potential to be developed in supporting food and non-food products, especially in Indonesia.

Three new species of the Sequester group of Pteromalus (Habrocytus) (Hymenoptera: Pteromalidae: Pteromalinae), Pteromalus (Habrocytus) boleensis Yan et Li sp. nov., Pteromalus (Habrocytus) longepedicelus Yan et Li sp. nov., and Pteromalus (Habrocytus) robustus Yan et Li sp. nov. are described and illustrated based on adult morphology and molecular data from Xinjiang, China. The DNA barcodes (ITS2) of Pteromalus (Habrocytus) boleensis sp. nov. and Pteromalus (Habrocytus) robustus sp. nov. have been generated and compared with all existing sequences of the Sequester species group. The results of morphological taxonomy and molecular identification are consistent. A key to all known species of the Sequester group in the world is provided.

Rapeseed (Brassica napus L.) is one of the most oil crop, and its commercial value is contingent upon its agronomic characteristics and oil quality. In this study, 73,226 single nucleotide polymorphisms (SNPs) across 95 rapeseed mutant lines derived from gamma rays and their original cultivar (‘Tamra’) obtained from genotyping-by-sequencing (GBS) was investigated gene ontology (GO) analysis and genome-wide association study (GWAS). GWAS was conducted on agronomic (plant height, ear length, thousand seed weight and seed yield) and oil (fatty acid and crude fat) traits. GO analysis showed that many genes displaying SNPs were involved in cellular processes, intracellular anatomical structures and organic cyclic compound binding. A total of 149 significant SNPs were associated with the agronomic traits (76 SNPs) and oil traits (73 SNPs). Bna.A05p02350D (SFGH) and Bna.C02p22490D (MDN1) were selected as novel candid genes for thousand seed weight. In addition, Bna.C03p14350D (EXO70) and Bna.A09p05630D (PI4Kα1) were selected as novel candidate genes for the erucic acid and crude fat content, respectively. These findings could facilitate the identification of optimal genotypes for breeding new cultivars, and association studies represent an economically efficient tool for mutant screening and the selection of elite rapeseed-breeding lines.

The fluid seepage in local-saturated zone of subgrade promotes the migration of fine particles in the filler, resulting in the change of pore structure and morphology of the filler and the deformation of solid skeleton, which affects the fluid seepage characteristics. Repeatedly, the muddy interlayer, mud pumping and other diseases are finally formed. Based on the theory of two-phase seepage, the theory of porous media seepage, and the principle of effective stress in porous media, a two-phase fluid-solid coupling mathematical model in local-saturated zone of subgrade considering the effect of fine particles migration is established. The mathematical model is numerically calculated with the software COMSOL Multiphysics○R, the two-phase seepage characteristics and the deformation characteristics of the solid skeleton in local-saturated zone of the subgrade are studied. The research results show that due to the continuous erosion and migration of fine particles in local-saturated zone of the subgrade, the volume fraction of fine particles first increases then decreases and finally becomes stable with the increase of time. And the volume fraction of fine particles for the upper part of the subgrade is larger than that for the lower part of the subgrade. The porosity, the velocity of fluid, the velocity of fine particles, and the permeability show a trend of increasing first and then stabilizing with time; the pore water pressure has no significant changes with time. The vertical displacement increase first and then decrease slightly with the increase of time, and finally tend to be stable. For a filler with a larger initial volume fraction of fine particles, the maximum value of the volume fraction of fine particles caused by fluid seepage is larger, and the time required to reach the maximum value is shorter. It can be concluded that in actual engineering, the volume fraction of fine particles in the subgrade filler should be minimized on the premise that the filler gradation meets the requirements of the specification.

Health comprises physical, mental and social dimensions whose interactions influence users’ experiences. Health experiences are within the context of environments. These contexts are definitive contributors to experiences – primarily because of the link to social dimensions as human beings - psychological and economic. Therefore, the study aims to investigate health resort users’ psycho-social and socio-economic characteristics to improve their access to quality healthcare. The objectives are identifying the socio-economic characteristics of an inclusive health resort, analysing the psycho-social characteristics of the inclusive health resort user, and analysing the effects of users’ psycho-social and socio-economic characteristics on their access to healthcare. The study employs the mixed research method (qualitative and quantitative). The researchers engaged in a pragmatic research philosophy that underscores positivist and interpretivist paradigms. The data collection instruments include survey questionnaires, an interview guide with a digital recorder, a direct participant observation schedule, field notes and photographs. The data analysis process involves the clustering and categorisation of data and examining concepts and themes. The research findings show a correlation between the users’ socio-economic status and access to quality healthcare in an inclusive health resort. The result further reveals that psycho-social and socio-economic characteristics of health resort users are quality healthcare access predictors. Therefore, the users’ social, psychological, and economic status should play a vital role in the design of an inclusive health resort by all stakeholders.

Glaciers in northern Pakistan are a prime source of fresh water, providing headwater in the Indus River System and serving as a lifeline to millions of people in the region. These glaciers undergo continuous changes by melting due to global warming or accumulation due to snowfall/precipitation at higher altitudes. In this study, we used remote sensing data to quantify glacier changes in spatiotemporal variability in the past three decades. Five glaciers in the Gilgit region (near the junction of the Hindukush and Karakoram Mountains) with an extent of less than 5 square kilometers were selected, namely Phakor glacier, Karamber glacier, East Gammu glacier, Bhort glacier, and Bad-e-Swat glacier. The fluctuations in these glaciers were monitored using a digital elevation model (DEM) and a cloud-free continuous series of Landsat satellite pictures from the minimal snow cover season. The annual climatic trends were studied through spatially interpolated gridded climate data WοrldClim version-1 climate database for 1970 – 2000. We used it to study the variations of minimum and maximum temperature, solar radiation, and precipitation by preparing sub-sets from the original global grids. The temporal assessment of Bhort, Bad-e-Sawat, East Gammu, Karamber, and other rivers was also carried out. It is observed that the glaciers in the Gilgit watershed are rather stable. The little variability of glaciers is due to their geographic condition, altitude, topography, and orientation. The mapped glacier classes have been validated to check the accuracy assessment through an error matrix method. The kappa coefficient from the error matrix has been calculated to be 84 %. The study makes a critical input to a greater understanding of watershed controlling and hydrological processes in the upper Indus catchment's Gilgit watershed.

Background: Kawasaki disease (KD) is a form of vasculitis that primarily affects children under the age of 5 years old. Patients may be missed diagnosis when initial clinical symptoms do not fulfill the traditional criteria. We aimed to analyze factors that clinicians could use to differentiate febrile children suspected of KD. Method: We retrospectively enrolled a total of 83 febrile children who were initially suspected of KD, but they did not meet the American Heart Association (AHA) criteria for a diagnosis. However, some of these patients were diagnosed with KD during their second visit. We analyzed patients' characteristics, clinical symptoms, and laboratory data. Results: In total, 50 patients were enrolled in the study. Of those, ten patients were diagnosed with KD on their second visit (group 1), while the other 40 patients still did not fit a KD diagnosis (group 2). A patient with a neutrophil to lymphocyte ratio greater than 1.33 combined with a C-reactive protein more than 33 mg/L was more likely to have KD. Conclusion: Among patients suspected of KD that did not initially meet the criteria, clinicians should pay special attention to elevated neutrophil-to-lymphocyte ratios and CRP levels and closely follow up such patients.

A comprehensive understanding of the connotation and basic characteristics of campus culture in vocational colleges is a prerequisite for ensuring their sustainable development. Campus culture in vocational colleges is a concentrated reflection of their educational philosophy, ideal beliefs, and value pursuits. It possesses basic characteristics such as practicality, vocational orientation, ethics, contemporaneity, integration, and regionality.

A single fracture is the basic unit of fracture medium, and the roughness of fracture wall surface is an important factor influencing hydraulic characteristics of the flow in bedrock fracture. However, effects of the shape and density of roughness elements (various bulges/pits on rough fracture wall surfaces) on water flow in a single rough fracture have not been thoroughly discovered. Thus the water flow in single fracture with different shapes and densities of roughness elements was simulated by using Fluent software in this study. The results show that in wider fractures the flow rate mainly depends on fracture aperture, while in narrow and close fracture medium the surface roughness of fracture wall is the main factor of head loss of seepage; there is a negative power exponential relation between the hydraulic gradient index and the average fracture aperture, i.e. with the increase of fracture aperture, the relative roughness of fracture and the influence weight of hydraulic gradient both decrease; and in symmetrical-uncoupled fractures there is a super-cubic relation between the discharge per unit width and average aperture. Above results would help to deepen the understanding of rough fracture seepage.

A phosphate/molybdate and cerium-modified phosphate/molybdate conversion coatings were deposited on a carbon steel surface and their protective and self-healing abilities were evaluated. Surface morphology and inner structure of the coatings were examined using FE-SEM-FIB and TEM techniques, chemical composition and element distribution depth profiles in conversion layers were determined using EDX measurements, whereas XPS was applied for the analysis of Mo and Ce oxidation states. Voltammetric measurements and EIS were performed to assess the corrosion behavior of the samples. The higher protective and stronger self-healing abilities were found for phosphate/molybdate/cerium conversion coating deposited in a sulphate-containing solution. This was attributed to higher values of both: total cerium and Ce(IV) content in the conversion layer as well as to lower number of structural defects in the coating. It was demonstrated that the micro-structural characteristics of protective coatings are also important in determining self-healing abilities.

The Suter curves for Wh and Wm characteristics of collected and the first time presented Four-quadrant (4Q) diagrams of 11 radial pump-turbine models with different specific speeds (nq=24.34, nq=24.8, nq=27, nq=28.6, nq=38, nq=41.6, nq=41.9, nq=43.83, nq=50, nq=56, and nq=64.04) are given in the paper, as well as the Suter curves for 2 pump models (nq=25, and nq=41.8) which were already published in the literature. These 11+2 curves were analyzed to establish a certain universal law of behavior in dependence on the specific speed. For the determination of existing laws in behavior, the fitting procedure using the Regression and Spline methods was used. The paper presents a research plan and structures that include: data collection of four-quadrant diagrams for models of pump-turbines and pumps with different specific speeds (nq), the procedure of recalculation of Four-quadrant diagrams of the models into Suter curves for Wh and Wm characteristics, the definition of the optimal point for the pump and turbine operating mode in pump-turbine models for different specific speeds, and developing numerical models in the MATLAB program to obtain the Universal Equation for the Wh and Wm characteristics. The scientific contribution of this paper is the firstly published original mathematical curve named Universal Equation for the Wh and Wm characteristics for radial pumps and pump-turbines. Application of the equation has been demonstrated at the pumping station where two radial pumps are installed. The calculation of transient processes was performed using the numerical model developed by the authors in the mathematical program MATLAB. Comparison of the transition process results has been made for the two cases - when input data in the numerical model have been firstly used with the values of Suter curves for Wh and Wm characteristics obtained by recalculation from the Four-quadrant operating characteristics (Q11, n11, M11) of model’s specific speed, and then secondly with the values of the Suter curves for Wh and Wm characteristics obtained from the Universal Equation.

In order to study the hydrothermal behavior of cotton fiber, the carbonization process and structural evolution of discarded cotton fiber (WCF) under hydrothermal conditions were discussed use microcrystalline cellulose (MCC) and glucose as model compounds. The results showed that high temperature was beneficial to the hydrolysis of discarded cotton fiber, and the yield of the sugar was 4.5% which was lower than that of MCC 6.51%. WFC and MCC are carbonized in 240~260 ℃ and 220~240 ℃ respectively, while the carbonation temperature of glucose is lower than 220 ℃. The quality ratio of C/O in WCF and glucose hydrothermal products is 5.79 and 5.85 respectively; three kinds of hydrothermal carbonization products have similar crystal structure and oxygen-containing functional groups, and the WCF carbonization products contain a lot of irregular particles while the main products of glucose carbonization are 0.5 μm carbon microspheres (CMCC). The results show that glucose is an important intermediate product of WCF hydrolysis carbonation, and there are two main paths of cotton fiber hydrothermal carbonization: some cotton fibers are completely hydrolyzed into glucose and the nucleation is formed, and then the carbon microspheres are grown; for the other part, the glucose ring of the polysaccharide oligosaccharide formed by the incomplete hydrolysis of cotton fiber in the hydrothermal environment of high temperature and pressure breaks, then forms the particulate matters.

Small and medium-sized enterprises (SMEs) help and support the country in financial and business aspects and employs in the country, overcomes unemployment, and creates job opportunities in different sectors of the country. The study aims to know the entrepreneurial-specific factors like age, gender, education, experience, and skills used as predictors for access to financing of small firms in Khyber Pakhtunkhwa. The questionnaire is used for data collection, and about 204 questionnaires were distributed, of which 192 returned and analyzed through binary logistic regression. The study results reveal that age and level of education have been found significant while gender, experience and skills have insignificant with the access to finance in Khyber Pakhtunkhwa, Pakistan.

A numerical method using combined detached-eddy simulation (DES) and cavitation model considering the rotation effect is used for unsteady cavitation flow field of the centrifugal pump. Closed type pump test system was established to obtain the pump performance and pressure pulsation characteristics under different flow rates and cavitation condition, which provide boundary conditions and verification of calculations. Based on the calculation results of the unsteady flow field of the centrifugal pump cavitation, the entropy generation analysis of the flow field and the pressure fluctuation characteristics were carried out. Then the relationship between cavitation and the deterioration of the centrifugal pump performance and the generation of the unstable operation excitation force was tried to reveal. The internal energy loss is mainly concentrated in the impeller, volute, and pump cavity area, which accounts for more than 85% of the total entropy generation. The characteristic frequency of about 0.333 Strouhal Number appears at the volute tongue due to the cavitation flow spread downstream.

In this paper, four lithological parameters, i.e. thermal conductivity, particle size, porosity and saturation, are investigated by combining experimental observations with numerical simulations to study the influence laws and mechanisms of action on the combustion process of methane hydrate sediments. The variation of combustion characteristics parameters such as flame height, effective combustion ratio and dimensionless discharge water mass with the lithological parameters are studied. In addition, the combustion mechanism of lithologic parameters on methane hydrate deposits is revealed. Combining the experimental results and simulation calculations, to optimize the combustion of methane hydrate sediments, it is recommended to use methane hydrate sediment samples with high saturation and low thermal conductivity, while the oxidant concentration and porosity of methane hydrate sediment samples should be increased.

In the interaction of the rolling stock and the upper structure of the railway track, intense dynamic loads occur. They have a destructive effect both on the parts of the rolling stock and on the elements of the superstructure of the track. In order to develop a durable, rational and reliably functioning design of cars and locomotives with good dynamic properties and good indicators of the impact of rolling stock on the railway track, along with theoretical computational studies, experimental studies are also required, which are usually the final stage in the design and implementation of rolling stock or modernization of existing ones. Locomotives and wagons in order to improve their strength and dynamic performance. The article presents the results of field tests to determine the dynamic performance of the type CKD6e diesel locomotive. The description of the preparation of the CKD6e shunting locomotive for testing is given. An analysis of the dynamic performance of a diesel locomotive during the passage of turnouts, on a straight section of the track and in a curve with a radius of 400 m, was carried out. The studies performed showed that the minimum value of the stability factor against wheel derailment on a straight section of the track is significantly higher than the standard value. The experimentally obtained ratio of frame forces to the static load from the wheelset on the rails, the coefficients of vertical dynamics of the first and second stages of suspension and the coefficient of stability against derailment of the wheel from the rail, registered on the track section in a curve with a radius of 400 m) meet the current requirements. A calculation scheme and equations of vertical oscillations are proposed, an analysis is carried out according to the graphs of movements of bogies and a locomotive body when moving along irregularities of different lengths at different speeds.

Temperature is the abiotic factors that strongly influence the biology and behavior of insects. Thus, we assessed the development of the egg parasitoids, Ooencyrtus submetallicus and Telenomus podisi, parasitizing eggs of the brown stinkbug, Euschistus heros, at different temperatures, in addition to estimating the average number of generations using temperature records for seven representative soybean producing regions in Brazil. The comparative biology study conducted evidenced that O. submetallicus and T. podisi had similar percentages of parasitism and emergence, life cycle duration (egg-adult), and longevity. The sex ratio and the number of adult parasitoid emerged per parasitized egg was superior for O. submetallicus. The study of thermal requirements evaluated temperatures of 16, 19, 22, 25, 28, 31, and 33 °C. Ooencyrtus submetallicus and T. podisi developed at temperatures between 16 and 31°C. The lower temperature (Tb) threshold for O. submetallicus and T. podisi was 9.3° and 6.7°C, while the thermal constant (K) was 336.9 and 272.7 degree days, respectively. The estimated average number of generations per year for both parasitoids was greater than the pest E. heros. Ooencyrtus submetallicus and T. podisi exhibited the same biological capacity to parasitize and to develop parasitizing E. heros eggs under laboratory studied conditions. The temperature range between 16° and 33 °C was favourable for the development of both parasitoids parasitizing E. heros eggs.

The purpose of the article is to determine the peculiarities of using of teaching elements of research-based training at the Institute of Human Sciences of Borys Grinchenko Kyiv University. Based on the focus group methodology, the authors identify the key methodological characteristics of research-based training, which have been put into basis of analysis of educational programs for the purpose of determining the application of tasks that contribute to the development of research skills of students. The study used a method of focus group. Its purpose was to obtain the necessary information from the participants to describe the methodological basis and justification of methods, forms, indicators, etc. of research-based training system among people who are competent, have experience in this field. After that, the method of "theoretical sampling" was used, which enabled to formulate generalized characteristics according to the results of focus groups. The practical value of the study is determination of the methodological characteristics of research-based training which is the basis for the application of tasks by university teachers that promote the development of research competence of students. The research is one of the first attempts to determine the methodological characteristics of research-based training in Ukraine.

One of the modern methods of improving operating characteristics of titanium and titanium-based alloys under conditions of friction and increased contact loads is the method of ion-plasma nitriding. The effect of nitriding of VT5 alloy (Al 4,5-6,7 %, V to 1,2 %, Mo to 0,8 % − analogue 3.7115) in the plasma of a glow discharge excited in a hollow cathode on its tribological characteristics in pairs with different materials in T-1 fuel and under dry friction conditions has been studied. For research and tribological tests, samples of VT5 alloy were nitrided in the plasma of a glow discharge excited in a hollow cathode at a temperature of 975 ± 15°C and a pressure of 58 ± 2 PA in a nitrogen-argon gas mixture with a nitrogen content of 78 %. Studies of samples of VT5 alloy after nitriding showed that the surface roughness Ra was in the range of 0.58-0.64, and the surface hardness HV5 was 525 ± 20 kgf/mm² at a base hardness of 325 ± 15 kgf/mm². Tribological tests were performed on a friction machine 2070 SMT-1 according to the scheme "cube - roller". Tests under conditions of friction with oil were performed at a load of 200 N. The sliding speed during the tests was 1.3 m/s, the test time was 75 sec. The test under dry friction conditions was carried out at a load of 100 N and a sliding speed of 0.785 m/s, the test time was 30 minutes. Low wear ability in relation to the nitrided titanium alloy VT5 (<2.4x10^-4 mm³/s), as well as friction coefficients at the level of 0.08 to 0.12 in the order of their growth had bronze VB-23NTS (Pd 18–22 %, Ni 3–4 %, Zn 3–4 %, Sb 3–4 %, P 0.15–0.3) r.O10C2N3, VB-24 (Sb 4.7–6, 2 %, P 0.4–0.9), steel 1.3505, cast iron GGG80, cemented steel 20Cr3MoWV.

By using various skill scores and spatial characteristics of spatial verification methods and tradi-tional techniques of the model evaluation tool (MET, V10.0.0), the gridded precipitation obser-vation CMPAV (V2.0) and three datasets that derived from local (LOC), Shanghai (SHA), and Grapes (GRA) model respectively are conducted to assess the 3 lead day rainfall forecast with 0.5-day intervals during summer of 2020 over central east China. Results have shown that LOC generally outperforms the other two for most skill scores but usually with relatively larger un-certainties than SHA, and it has the least displacement errors for moderate rainfall among the three datasets. However, the rainfall of GRA has been heavily underestimated and accompanied with large displacement error. Both LOC and SHA have shown almost equitable abilities in forecasting convection and rainstorms of the large area but with a slightly over-forecast of local convection, while LOC likely over-forecasts the local rainstorms. In addition, SHA slightly favors over-forecast on a broad scale range and a broad threshold range, and LOC slightly misses the rainfall exceeding 100 mm. Generally, for a broadly comparative evaluation on rainfall, the popular dichotomous methods should be recommended under considering reasonable classifi-cation of thresholds if the accuracy is highly demanded. And most spatial methods should be suggested to conduct with proper pre-handling of non-rainfall event cases. Especially, the veri-fications including spatial characteristic difference information could be recommended in a computationally sufficient environment.

Rainfall is a major climate parameter whose variation in space and time influences activities in different weather sensitive sectors such as agriculture, transport, and energy among others. Therefore, accurately forecasting rainfall is of paramount importance to the development of these sectors. In this regard, this study sought to contribute to quantitative forecasting of rainfall over Eastern Uganda through assessing the Weather Research and Forecasting model’s ability to simulate the intra–seasonal characteristics of the September to December rain season. These were: onset and cessation dates; wet days and lengths of the wet spells. The data used in the study included daily ground rainfall observations and lateral and boundary conditions data from the National Centers for Environmental Prediction (NCEP) final analysis at 1 0 horizontal resolution and at a temporal resolution of 6 hours for the entire study period were used to initialize the Weather Research and Forecasting (WRF) model. The study considered four weather synoptic weather stations namely; Jinja, Serere, Soroti and Tororo. The results show that the WRF model generally simulated fewer wet days at each station except for Tororo. Also, the WRF model simulated earlier onset and cessation dates of the rainfall season and overestimated the length of the wet spells.

In the natural environment, sand accumulation and desertification can influence the efficiency of photovoltaic arrays. In this study, PV module output characteristics were examined under different sand particle size, varying sand densities and inclination angles, and at wind speeds of 5m/s, 10m/s, and 15m/s. Both theoretical and experimental results showed that the output power of the module declines with increasing sand density. As the sand particle size increases, the module maximum output power rises and then stabilizes. The two control variables, namely sand density and sand particle size, influence the module temperature and light transmittance distinctly. Contrary to the impact of sand density on the module filling factor curve, the module filling factor exhibits varying trends under different sand particle sizes. Additionally, the pattern of the module filling factor as a function of sand density contrasts with that of the module temperature under analogous conditions. Specifically, when the sand density on the PV module surface increases from 0 to 40g/m², there is a 32.2% reduction in maximum output power. At a wind speed of 15m/s, this reduction was found consistent across all wind speed categories. Furthermore, the trend of the module filling factor rel-ative to sand accumulation density contrasts with the module temperature trend under analogous conditions. Notably, the filling factor reached its apex at a sand accumulation density of 35g/m², which corresponded to the module temperature's nadir during the experiment.

Weather surveillance radars routinely detect smoke of various origin. Of particular significance to the meteorological community are wildfires in forests and/or prairies. For example, one responsibility of the National Weather Service in the USA is to forecast fire outlooks as well as to monitor wild fire evolution. Polarimetric variables have enabled relatively easy recognitions of smoke plumes in data fields of weather radars. Presented here are the fields of these variables from smoke plumes caused by grass fire, brush fire, and forest fire. Histograms of polarimetric data from plumes contrast these three cases. Most of the data are from the polarimetric Weather Surveillance Radar 1988 Doppler (WSR-88D aka Nexrad, 10 cm wavelength) hence the wavelength does not influence these comparisons. Nevertheless, in one case simultaneous observations of a plume by the operational Terminal Doppler Weather Radar (TDWR, 5 cm wavelength) and a WSR-88D is used to infer backscattering characteristic and hence sizes of dominant contributors to the returns. In addition, comparisons with observations by other investigators of plumes from urban area but at a 5 cm wavelength are made. To interpret some measurements Computational Electromagnetics (CEM) tools are applied.

Bulukumba Regency, South Sulawesi, Indonesia is one of the centres for whiteleg shrimp, Litopenaeus vannamei production that applies intensive technology. However, no information has been obtained regarding the characteristics and status of water quality in coastal areas with environmentally friendly concepts and the potential to receive a waste load. The study aimed to determine the performance of whiteleg shrimp culture in relation to temporal and spatial aspects and characteristic and water quality status. Measurement and sampling of water were carried out before stocking/initial of culture whiteleg shrimp (rainy season) and end of culture/after harvesting of whiteleg shrimp (dry season) at two locations in the coastal area of ​​Bulukumba Regency, namely Bonto Bahari Subdistrict (BB) and Gantarang Subdistrict (GT). Variables measured and analyzed included temperature, salinity, pH, dissolved oxygen, nitrate, nitrite, ammonia, phosphate, total suspended solids, and total organic matter. Data analysis with descriptive statistics, multivariate statistics, and non-parametric statistics. The Storet (Storage and Retrieval) method was used to determine the water quality status. The results showed that the culture of whiteleg shrimp was technology-intensive with a stocking density of 110 - 220 ind/m² with productivity between 13.9 - 44.4 tons/ha/cycle. The predicted waste load of N is 28.00 tons/cycle and P reaches 6.61 tons/cycle. Another result was that changes in water quality status during the rainy season were classified as moderately polluted at the BB location and complying quality standards at the GT location, while in the dry season, both locations were categorized as heavily polluted. Variables of water quality that caused the decrease in water quality status in both locations (BB and GT) were observed to increase salinity, nitrate concentration, and ammonia concentration. However, there was a decrease in dissolved oxygen concentration in the dry season.

Molecular and morphological properties of poly(vinyl chloride) grains produced by suspension polymerization of VCM in the presence of a mixture of three kind of initiators (i.e. fast, mild and slow) (named as Cok process) was experimentally investigated in a pilot-scale reactor. The results obtained here were initially compared with a isothermal regular process (named as control process) and then with those obtained already for other productivity-enhancing polymerization techniques (i.e. nonisothermal and fast initiator dosage process). The results showed that, in contrast to nonisothermal and fast initiator dosage process, the addition of initators mixture at the beginning of the reaction has the smallest influence on molecular weight and polydispersity index compared to control process. It is obvioused that Cok-PVC grains have the lowest cold plasticizer absorption and porosity among these mentioned processes. Scanning electron microscopy (SEM) showed that the particles produced by Cok process are more regularly shaped, with a smoother surface compared with the control product. According to the literatures, all three productivity-enhancing techniques lead to an apparent quality enhancement, higher flowability and greater bulk density of final grains. While both processes of continous initiator dosage and nonisothermal polymerization broaden the particle size distribution of final PVC grains, applying initiator mixture produces particles with the same particle size distribution as control process. The SEM images processing showed that Cok process deccelerates the formation of a three-dimensional skeleton of primary particles relative to the control polymerization. In comparison with nonisothermal trajectory and continous fast initiator dosage system, the Cok polymerization process leads to the most delay of motionless conversions and fusion time as well.

Polysaccharide from Ficus carica L. (FCP) exert multiple biological activities, as a biological macromolecule, the available knowledge about the specific structures and mechanisms of biological activity of purified 'Brunswick' fig polysaccharide is currently limited. In the present study, by chemical purification and characteristics identified via specific instruments, and then the impact of FCP on the immunomodulation activity in vitro and in vivo was examined. Structural char-acteristics showed that the molecular weight of the FCP was determined to be 127.5 kDa, the primary monosaccharides present in the FCP were galacturonic acid (GalA), arabinose (Ara), galactose (Gal), rhamnose (Rha), glucose (Glc), and xylose (Xyl) at a ratio of 0.321:0.287:0.269:0.091:0.013:0.011. Based on the investigation of in vitro immunomodulatory ac-tivity, FCP was found to stimulate the production of NO, TNF-α, and IL-6 and increased the pi-nocytic activity of macrophages. Further analysis revealed that FCP activated macrophages by interacting with toll-like receptor 4 (TLR4). Moreover, the in vivo test results indicate that FCP showed significant increase serum pro-inflammatory factors in immunosuppressed mice. Overall, this study suggests that FCP has the potential to be utilized as a novel immunomodulator in the pharmaceutical and functional food industries.

Soil transverse isotropy results in different stiffness characteristics in the horizontal and vertical directions. However, the effect is usually neglected in the seismic motion analysis. In this study, an equivalent linear anisotropic soil model was established based on the finite element method and investigated the impact of anisotropic parameters on ground motion at the site under various seismic wave inputs. It is found that the anisotropic parameters have a more significant effect for the seismic waves with the dominant frequency closer to the fundamental frequency of the site. As an example, the soil dynamic parameters in Shanghai Yangshan Port were calibrated by a series of bending elements, resonance columns, and cyclic triaxial tests. The influences of anisotropy on the peak ground acceleration (PGA) and response spectrum are studied for Yangshan Port. Addi-tionally, the standard design response spectra considering the soil anisotropy were provided. A comparison reveals that the existing isotropic design response spectrum may lead to dangerous seismic design for the structures at Yangshan port.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

This study focuses on traffic condition analysis, especially in under developing country India and makes more visible of traffic flow by using traffic flow theory in order to understand real traffic condition. India is one of rapid economic growing countries and large market with second largest population 1.3 billion in 2018. On the other hand, there are social issues such as environment air pollution and global warming by traffic CO2 emission of transportation. This kind of condition is not only in India, but in other South East Asia and Africa in future. From recent more than one-month traffic observation in a typical major city Ahmedabad in Gujarat state, which has about 8 million population and industrialized city. In terms of traffic data collection, 14 CCTV cameras are used in the city. Based on multiple traffic cameras monitoring, author found the unique traffic flow characteristics and compares traffic flow theory. In this study, it is described what is key parameters to show real traffic congestion condition and how these congestion occurs.

Background: Gastrointestinal stromal tumors (GIST) are rare mesenchymal neoplasms of the gastrointestinal tract (GIT) that represent approximately 1 to 2 percent of primary gastrointestinal (GI) cancers. Owing to their rarity, very little is known about the overall epidemiology and prognostic factors of the pathology. The purpose of this study is to investigate the clinical characteristics, survival outcomes, and independent prognostic factors of patients with GIST in the past decade. Methods: A total of 2,374 patients diagnosed with GIST, between 2010 and 2017, were ultimately enrolled in our study by retrieving the Surveillance, Epidemiology, and End Results (SEER) database. We analyzed demographics, clinical characteristics, and overall mortality (OM) as well as cancer-specific mortality (CSM) of GIST. Variables with a p value < 0.01 in the univariate Cox regression were incorporated into the multivariate Cox model to determine the independent prognostic factors, with a hazard ratio (HR) of greater than 1 representing adverse prognostic factors. Results: Multivariate cox proportional hazard regression analyses of factors affecting all-cause mortality and GIST related mortality among US patients between 2010 and 2017 revealed higher overall mortality in Non-Hispanic Blacks (HR= 1.516, 95% CI 1.172-1.961, p= 0.002), age 80+ (HR= 9.783, 95% CI4.185-22.868, p= 0), followed by age 60-79 (HR= 3.408, 95% CI 1.488-7.807, p=0.004); male patients (HR= 1.795 , 95% CI 1.461-2.206, p=0); advanced disease with distant metastasis (HR= 3.865 , 95% CI 2.977-5.019, p=0), followed by regional involvement by both direct extension and lymph node involvement (HR= 3.853, 95% CI 1.551-9.57, p=0.004); and widowed patients (HR= 1.975, 95% CI 1.494-2.61, p= 0), followed by single patients (HR= 1.53, 95% CI 1.154-2.028, p=0.003). The highest CSM was observed in the same groups, except widowed patients and patients aged 60-79. The highest CSM was also observed among patients that underwent chemotherapy (HR= 1.687, 95% CI 1.19-2.392, p= 0.003). Conclusion: In this United States population-based retrospective cohort study using the SEER database, we found that non-Hispanic blacks, male patients, and patients older than 60 years have a higher mortality with GIST. Furthermore, patients who received chemotherapy have a higher GIST specific mortality and married patients had a lower mortality. However, we do not know to what extent these independent prognostic factors interact with each other to influence mortality. This study paves the way for future studies addressing those interactions. The results of this study may help treating clinicians to identify patient populations associated with dismal prognosis as those may require closer follow-up and more intensive therapy; furthermore, with married patients having a better survival, we hope to encourage clinicians to involve family members of the affected patients early in the disease course as the social support might impact the prognosis.

The goal of our study was to examine the effect of regional characteristics of living environment on individual a priori and a posteriori dietary patterns of the Russian population. For the analysis, we used cross-sectional data from the Epidemiology of Cardiovascular Diseases in the Regions of the Russian Federation study of 2013-2014. The sample included 18,054 men and women 25-64 years of age from 12 regions. Based on the frequency of consumption of basic foods, four a posteriori empirical dietary patterns (EDPs), along with an a priori cardioprotective dietary pattern (CPDP) were identified. To describe the regional living environment, 5 regional indices were used. The adherence to the meat-based EDP was directly associated with deterioration of social living conditions and the more northerly location of the region of residence. The probability of CPDP increased with deterioration of social living conditions, an aggravation of demographic crisis, higher industrial development of the region, as well as with a decline in the economic development of the region, income and economic inequality of the population. We detected some gender-dependent differences in associations. The revealed patterns reflect the national dietary preferences of Russians, and regional indices characterize the effect of living environment.

The development in the field of ceramics has been increasing over the past several decades. Among all of the dental ceramics, zirconia ceramics show very good mechanical properties and a significant improvement in mechanical function. However, it is properly established that each step of the fabrication process of zirconia ceramics must be controlled to achieve the expected mechanical properties. These steps include the block constructing, sintering process, machining and surface processing. Recent advances have focused on zirconia ceramics in forming and sintering processes, mechanical properties, combining with various materials, and on surface processing. All these items provide conceptions about the formability and machinability of the zirconia. Until now, very excellent studies have been done to specify the evolution of microstructures, phase and mechanical properties of zirconia ceramics during the sintering process. However, more studies are required in this field. This paper aims to demonstrate general views and various studies in the field of zirconia ceramics. The properties, applications and tests performed and the recent developments in the field of zirconia bioceramics are discussed.

This paper uses the spatial analysis software GeoDa as a tool, takes GRP (Gross regional product) of Sichuan Province in 2012 and 2018 as the dependent variable, and takes the city (autonomous prefecture) factor-driven, investment-driven and innovation-driven indicators as the dependent variable to explore the impact of innovation activities on regional economic development and the spatial distribution characteristics of regional economy. Through the comparison of the global correlation and local correlation, this paper explores the crux of the regional economic polarization and unbalanced development, and puts forward some measures to solve the existing economic development problems, such as cultivating and improving the regional industrial dependence, accelerating the regional transportation accessibility and convenience, and constructing the regional collaborative innovation system, So as to achieve the strategic goal of the construction of innovative Province in Sichuan Province.

To realize the utilization of peanut shell, this study investigates the combustion behavior, chemical kinetics, and thermodynamic parameters of peanut shell using TGA under atmospheric air. Results indicate that increasing the heating rate leads to higher ignition, burnout, and peak temperatures, as observed in the TG/DTG curves shifting to the right. Analysis of combustion performance parameters suggest that higher heating rates can enhance combustion performances. Kinetic analysis using two model-free methods, KAS and FWO, shows that the activation energy (Eα) ranges from 93.30 to 109.65 kJ/mol for FWO and 89.72 to 103.88 kJ/mol for KAS. The data fit well with coefficient of determination values (R2) close to 1. Pre-exponential factors using FWO range from 2.19×106 to 8.06×107 s–1, and for KAS range from9.72×105 to 2.25×107 s–1. Thermodynamic analysis indicates a low-energy barrier (≤ ±6 kJ/mol) between activation energy and enthalpy changes, suggesting easy reaction initiation. Furthermore, variations in enthalpy (ΔH), Gibbs free energy (ΔG), and entropy (ΔS) upon conversion (α) suggest that peanut shell combustion is endothermic and non-spontaneous, with the generation of more homogeneous or well-ordered products as combustion progresses. These findings offer a theoretical basis and data support for the further utilization of agricultural biomass.

The heat generated during the startup process of dry gas seals, such as the friction heat of the asperities, viscous shear heat, and the expansion heat of the gas film, easily leads to seal failure and endangers the stable operation of turbomachinery. This study combines the statistically modified contact model and the average Reynolds equation by considering the adiabatic index and the microscale effects of dry gas seals to explore the heat generation characteristics of dry gas seals formed in series at multiple times. In particular, the change laws and influencing factors among the components, including the friction heat of asperities and the shear heat and expansion heat of the gas film and total heat, are investigated. A comparative analysis indicates that the slip flow effect increases the total heat during the startup process. The friction heat is much greater than expansion heat and shear heat. Despite constant acceleration, exponential acceleration, or Harrision acceleration, the heat changes are uneven during the startup process. In particular, the heat changes sharply in the early stage and gently in the later stage. The Harrision acceleration mode is the most conducive to sealing stability.

The Gulong shale oil reservoir is formed in freshwater to slightly saline lacustrine basins, mainly consisting of pure shale geological structure, which is quite different from other shale reservoirs around the world. Currently, the development of Gulong shale oil mainly relies on hydraulic fracturing, while the subsequent shut-in period for imbibition has been proven to be an effective method for enhancing shale oil recovery. To clarify the characteristics of fluid occurrence space and the variation of fluid occurrence during saltwater imbibition in Gulong shale, this paper carried out porosity and permeability tests on Gulong shale cores, and analyzed the fluid occurrence space characteristics and imbibition oil recovery based on nuclear magnetic resonance (NMR). In the porosity and permeability tests, the porosity measured by saturation method was calibrated using NMR T2 spectra. Combined with the identification of fractures in shale cores using micro-CT and the analysis of porosity and permeability parameters, it was found that the permeability of shale cores was related to the development of fractures in shale cores. Through the testing and analysis of NMR T1-T2 two-dimensional spectra of the shale cores before and after saturation with oil, it was found that the shale mainly contains heavy oil, light oil, and clay-bound water, and they were distributed in different positions in the T1-T2 spectrum. Finally, the T1-T2 two-dimensional spectra of the shale core at different imbibition stages were analyzed, and it was found that the saltwater mainly entered the minuscule inorganic pores of clay minerals during the imbibition process, and squeezed the larger-sized inorganic pores containing light oil through the hydration expansion effect, thus expelling the light oil from the shale core and achieving the purpose of enhanced oil recovery.

Facing the tasks and challenges going forward, a pilot of the Indonesian Naval Aviation Center was required to be brave in taking risks, especially in carrying out its main tasks, so it was expected that a pilot of the Indonesian Naval Aviation Center had intelligence, especially in finding appropriate solutions and alternatives to address every task challenges dynamics in situations that often changed quickly. The purpose of this study was to identify the personal character and performance that should be owned by the pilot of the Indonesian Naval Aviation Center. This research used a qualitative approach with a contextual and constructional meta-analysis study method. The results of this meta-analysis study concluded that in line with the essence of personal character that is defined as the personal aspects of a work that allows workers to achieve superior performance. These personal aspects include nature, emotive-motives, value systems, attitudes, knowledge, and skills, where the personal character would produce an optimal performance on a pilot of the Indonesian Naval Aviation Center.

Фундук является одним из самых ценных орехов в мире благодаря своим уникальным органолептическим свойствам и питательным характеристикам. Данная работа была направлена ​​на анализ некоторых физико-химических свойств различных сортов фундука, выращиваемых в Закаталы (Азербайджан), а именно Ата-баба, Эльбари, Топкара, Фирован, Насими, Галиб, Мирзебейли, Тала, Даш финтик, Барли, Азери и Сачагли. В целом результаты показали статистически значимые различия между изучаемыми сортами. Плотность ядер в зависимости от сортов фундука варьировала от 0,71 г/см ³ (азери) до 1,03 г/см ^{3 .}(Сачакли). Очищенные плоды Дашфиндыг в среднем были тяжелее (1,64±0,34 г), а очищенные плоды Насими, Калиб, Мирзебейли и Сачакли в среднем легче (0,8±0,23 г, 0,8±0,31 г, 0,8±0,20 г и 0,80 г). ±0,09 г соответственно.В неочищенном виде самыми тяжелыми были орехи Дашфиндык (3,70±0,34 г), а самыми легкими из всех сортов были орехи Насими и Калиб (2,0±0,48 г и 2,0±0,36 г соответственно). - орехи баба составляют 49 масс./ядро, %, у остальных изученных сортов - 33,3-45,3 мас.%. Орехи насими имеют округлую форму (в экваториальной зоне); талы, ата-баба, фирован и азери - округло-продолговатые; топкара , Барли и Даш финдык – продолговатые; Эльбари, Калиб, Мирзебейли и Сачакли – удлиненные. Фирован, Тала и Топкара имеют более толстую скорлупу. Ата-баба значительно опережает другие сорта по выходу ядер (490 кг/1 т орехов) , На втором месте по этому показателю находится Тала (453 кг/1 тонна орехов), на третьем – Топкара (433 кг/1 тонна орехов). По максимальной жирности выделены сорта Мирзебейли (77,00±2,20 г/100 г ядер) и Фирован (75,0±3,08 г/100 ядер), по белку - Сачакли (16,02±0,50 г/100 ядер) и Ата-баба ( выделено 15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора. 50 ед/100 ядер) и Ата-баба (15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора. 50 ед/100 ядер) и Ата-баба (15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора.

Satellite measurements are one of the main sources of data on the state of the marine environment. To obtain information about the sea brightness coefficient , it is needed to correctly carry out atmospheric correction. In the presence of dust aerosol over the Black Sea, physically incorrect values of the spectral brightness coefficient often occur, and specifically negative values in the IR region of the spectrum. The main objective of the study is to evaluate the influence of dust aerosol on the spectral dependence of sea brightness, based on analytical calculations from the transfer theory using the principle of plane-parallel layers and results of validation of AERONET-OC field and remote sensing data. The work analyzes spectral dependence of the first error eigenvector of the standard atmospheric correction in the presence of dust aerosol. As result it is given that with an absorbing aerosol, the atmospheric correction error is described by the spectral course of molecular scattering, i.e. close to

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

Liver cirrhosis leads to hepatic dysfunction and life-threatening conditions. Though clinical efficacy of autologous bone marrow-drived mesenchymal stem cells (BM-MSC) transplantation in alcoholic cirrhosis (AC) was demonstrated, the relevant mechanism has not been elucidated. We aimed to identify predictive factors and gene/pathways for responders after autologous BM-MSC transplantation. Fifty-five patients with biopsy-proven AC underwent autologous BM-MSC transplantation. The characteristics of responders who showed improvement in fibrosis score (≥ 1) after transplantation were compared with those of non-responders. BM-MSCs were analyzed with cDNA microarrays to identify genes and pathways that were differentially expressed in responder after transplantation. Thirty-three patients (66%) were responders. In the multivariate analysis, initial high Laennec score (p=0.007, odds ratio 3.73) and performance of BM-MSC transplantation (p=0.033, odds ratio 5.75) were predictive factors for responder. Three genes (olfactory receptor 2L8, microRNA4520-2, and chloride intracellular channel protein 3) were upregulated in responders and 11 metabolic pathways (inositol phosphate, ATP-binding cassette transporters, protein kinase signaling, extracellular matrix-receptor interaction, endocytosis, phagosome, hematopoietic cell lineage, adipocytokine, peroxisome proliferator-activated receptor, fat digestion/absorption, and insulin resistance) were upregulated in non-responders (p<0.05). BM-MSC transplantation is warranted treatment for AC patients with high Laennec score. Cell-based therapy utilizing response-relating genes or pathway can be treatment candidate.

The purpose of this study was to see how feeding cotton gin trash (CGT) as an alternative meal affected the growth performance, carcass features, and meat quality of Mecheri ram lambs. A growth performance trial was conducted with thirty-two weaned Mecheri ram lambs from four months to nine months (180 days) of marketing age and assigned into four groups (T1, T2, T3 and T4) of eight animals in each group. The lambs were fed with CGT at 0 (T1), 25 (T2), 50 (T3) and 75 (T4) per cent inclusion levels in the roughage portion at 60:40 roughage: concentrate ratio. All the group of animals were fed on dry matter requirement basis at four per cent of their body weight. The lambs fed with 75 (T4) and 50 (T3) per cent inclusion level of CGT showed signifi-cantly (P<0.01) higher total body weight gain (kg) than T1 (14.54) and T2 (15.05) groups. The av-erage daily gain (g) of lambs in T3 (99.24) and T4 (105.51) were significantly (P<0.01) higher than T1 (80.77) and T2 (83.61) groups. Over the course of the 180-day trial period, there was no statisti-cally significant difference in the average DMI (g) between the groups (P>0.05), however the lambs in T4 demonstrated higher feed efficiency (7.4) than the T1 (9.3) group. The slaughter studies revealed that the lambs in T4 followed by T3 group registered significantly (P<0.01) higher hot carcass weight, dressing percentage and Meat: Bone ratio than T2 and T1 group ani-mals. The weights of the liver, spleen, head, stomach, and intestines empty were considerably (P<0.05) larger in the T3 and T4 groups than in the other groups, although there was no signifi-cant (P>0.05) difference in the weights of edible and inedible offals. Meanwhile, there were no significant variations (P>0.05) in pH, water holding capacity, shear force value, sensory charac-teristics, or proximate composition of meat across treatment groups. In accordance to the find-ings, CGT can be added up to 75% of the roughage component in sheep feed as an effective un-conventional supplementation, as it improves body weight, feed efficiency, and carcass characteristics in Mecheri ram lambs.

Vibro-fluidized dry coal beneficiation involves the unavoidable mixing of -1 mm coal dust into the fluidized bed, which compromises the stability and homogeneity of the bed density and reduces the effectiveness of fine-grained coal separation. In order to understand the features of coal powder separation and mixing (-1 mm) in a vibrating fluidized bed, as well as to achieve a uniform and stable bed density, a wide-grained dense medium consisting of -1 mm coal dust and 0.3-0.15 mm magnetite powder was homogeneously mixed in this work. The degree of density separation in the entire bed was examined, as well as the local mixing properties of the Wide-grained Dense Medium. It was discovered that when low vibrational energy was introduced at the same gas velocity, particle separation was enhanced in comparison to the usual fluidized bed. Little bubbles were found to ensnare fine coal dust and migrate upward, increasing density separation. The introduction of high vibrational energy leads to particle disorder within the bed and an increase in the level of particle mixing. The beneficial effects of vibration on the bed are diminished when the gas velocity is gradually increased under specified vibration circumstances. This causes big bubbles to develop more frequently, which increases particle mixing. Among them, the 1-0.5 mm fine-grained coal exhibits the best mixing state; it is less impacted by variations in air velocity and vibration levels, whereas the -0.5 mm coal dust is more affected by each of these variables. Furthermore, a wide range of air velocity regulation without a significant segregation state change was discovered to be achievable by the particle system under vibration circumstances of f=25Hz A=1mm and f=25Hz A=2mm.

In order to effectively utilize red mud, an aluminum industrial waste, the stabilized soil material was developed using nano-SiO2 synergistically modified red mud, and the strength characteristics of the stabilized soil were analyzed to clarify the feasibility of such stabilized soil serves as a road base material. Through different combination schemes, the effects of different nano-SiO2 and cement contents on the strength of the stabilized materials were explored. The test results show that: in the synergistic modification of nano-SiO2 and cement, nano-SiO2 can significantly improve the early unconfined compressive strength of red mud-based stabilized soil; in the synergistic modification of nano-SiO2, gypsum and cement, the 7-d unconfined compressive strength of red mud-based stabilized soil is greater than 2 MPa, which meets the strength requirements of road base materials and shows the superiority of synergism. The nominal stress-strain curves are divided into five stages: compressed and compacted stage, elastic deformation stage, plastic deformation stage, damage deformation stage and residual deformation stage. The macroscopic compressive damage pattern of the specimens shows that the modified red mud-based stabilized soil mostly exhibits brittle damage.

This paper examines the influence of the petrographic characteristics of sandstones from Klepa Nafpaktias (Greece) on their suitability in construction (concrete) and energy storage applications. For this scope, ten sandstones were collected in order to study their petrographic characteristics using petrographic microscope and a GIS software as well as their basic physical, mechanical and physicochemical properties. Concrete specimens (C25/30) were produced with constant volume proportions, workability, mixing and curing conditions using different sizes of each aggregate type. Aggregates were mixed both in dry and water saturated states in concrete. Three different types of sandstone aggregates were examined and classified in three district groups according to their physicomechanical properties, petrographic characteristics and surface texture. The classification in groups after the concrete compressive strength test (UCS) verified the initial classification in the same three groups relative to their grain size from coarse to fine grained. As the grain size decreases their physicomechanical and physicochemical properties are getting better resulting in higher concrete strength values (25 to 32 MPa). Furthermore, the proposed ratio C/A (crystals/ mm2) seems to influence the aggregate properties which constitute critical factors for the final concrete strength, presenting the more fine grained sandstones as the most suitable for concrete aggregates. Concerning the use of Klepa Nafpaktias sandstones as potential energy reservoirs, the studied sandstones have the appropriate physicochemical properties for the implementation of a financially feasible CO₂ capture and storage scenario.

The corrected mechanism model of battery voltammetric function is helpful to guide the development and application of battery. There are two scientific issues that need to be answered: First, how many mechanisms do batteries have; Second, how to establish the mechanism model separately under the overlapping of these mechanisms. Volt-ampere characteristics of both linear state and nonlinear state exist; the monotonic decreasing of volt-ampere characteristics indicates that the battery have only three kinds of mechanisms. Without changing the basic form of the function and under the principle of the mechanism function’s working region considered, we propose a mechanism function which satisfies the monotonic decreasing characteristic of the voltammetric curve of battery, via the derivative law of each mechanism function in the voltammetric function of battery. By using the voltammetric data, the obtained cell mechanism function can accurately predict the potential (current or voltage) when the independent variable of the cell is zero, and provide the theoretical basis for the internal working mechanism of the cell, which can guide the practice.

The study provide insights into the technological characteristics of green practices adoption and the potential benefits they offer in terms of socio-economic development, environmental and public health. The study adopted a cross-sectional research design. A structured questionnaire was developed to collect quantitative data from the participants. The questionnaire include closed-ended questions, Likert scale items, and demographic questions. Both stratified and simple random sampling techniques were employed to select the study participants (government officials, employees, managers, and community members). A total of 321 copies of questionnaires were duly filled and returned. The collected data were analyze using descriptive statistics, such as frequencies, percentages, mean, and standard deviation, were used to summarize the data and provide an overview of the key variables related to green practices adoption. The findings indicate that the manufacturing company in Ogun State, Nigeria, has shown moderate commitment to adopting green practices. While there is room for improvement in certain areas, such as waste-to-energy technologies and green building practices. Additionally, green practices have positively influenced employee well-being and community health, while aligning with the company's commitment to safeguarding the environment and public health.

Among endocrine cancers, thyroid carcinoma is the most prevalent type of cancer. It's prevalence has been increased throughout the world during the last decades, which shows great regional variations. Considering the increasing prevalence and occurrence of thyroid cancer cases, in this study we: Among endocrine cancers, thyroid carcinoma is the most prevalent type of cancer. It's prevalence has been increased throughout the world during the last decades, which shows great regional variations. Considering the increasing prevalence and occurrence of thyroid cancer cases, in this study we decided to evaluate the clinical and pathological charactristics of this endocrine system cancer in the population of thyroid cancer patients reffered to imam Khomeini Hospital in Sari between March 2014 and March 2021. decided to evaluate the clinical and pathological charactristics of this endocrine system cancer in the population of thyroid cancer patients reffered to imam Khomeini Hospital in Sari between March 2014 and March 2021.

The emergence of acute, severe non hepA–E hepatitis of unknown etiology (ASHUE) has attracted global concern owing to the very young age of the patients and its unknown etiology. Although this condition has been linked to several possible causes, including viral infection, drugs, and/or toxin exposure, the exact cause remains unknown; this makes treatment recommendations very difficult. In this review, we summarize recent updates on the clinical manifestations, complemented with laboratory results, case numbers with the global distribution and other epidemiological characteristics, and the possible etiologies. We also provide the proposed actions that could be undertaken to control and prevent further spread of this hepatitis. Since many etiological and pathological aspects of the acute non hepA–E hepatitis remain unclear, further research is needed to minimize the severe impact of this disease.

The automobile industry is often believed to be moving towards electric vehicles. Hybrid electric vehicles (HEVs) and electric vehicles (EVs) are anticipated to dominate the automotive industry. Regenerative braking is one of the modern approaches that recharge the battery by extracting the kinetic energy from the braking thus improving the vehicle range. However, the rate of current supplied by regenerative braking to the battery is a major concern as lithium-ion (Li-ion) is susceptible to failure due to the intensity of the charging-discharging rate, and operating temperature. So, this review article focuses on the effect of regenerative braking on the life of the battery and measures being taken to protect the battery from higher charging during regenerative braking. Various research articles are considered for observing the effect of regenerative braking on battery life. It is found that longer duration charging current obtained from regenerative braking that is irrespective of current intensity is the prominent factor of battery deterioration. If the SOC and the temperature are not in the optimal range, the Lithium plating rate increases. However, a higher level of regenerative braking increases the battery life even at high SOC and temperature by reducing the Depth of Discharge (DOD) and by using shorter recharging periods.

Higher order femtoscopy measured to examine the heat exchanger characterization of the fluid debris produced in the collisions and investigated a remarkable suppression in the bosons interferences measurement. The analogous suppression can be analyzed to explore the coherence of boson thermal particle production sources at unprecedented energies. We illustrate the particles emissions from radiated sources with statistical coherence which induce the thermal particles interferences to probe the peculiarity of the heated sources as well as the distinctions about the heat exchangers in the collisions at higher temperature. We perspicacious that the bosons seem to the pertinent aspirant of heat exchanger, and the normalized three particles correlators evaluate the existence of such hybrid phases significantly. The key point of this research is that we analyze the three particles correlations with their normalized correlations by difference equations to determine the characteristics of heat exchanger and its applications. With such distinctive and efficient approach, we observe a significant difference in the correlation functions at higher temperature and momenta regimes.

Low-temperature accumulation is one of the essential stages in the growth process of woody ornamental plants. In this study, two different low-temperature treatments, 6℃ and 10℃, were used to analyze the effects of different low-temperature treatments on dormancy release and flowering of the 'Gulihong' plant using artificial low temperatures. Based on the experimental results, four typical early-blooming Prunus mume cultivars widely planted in Yangling area of Henan Province, China, including 'Zaoyudie', 'Zaohualve', 'Nanjing gongfen', and 'Gulihong', were selected as the experimental materials. The effects of low-temperature accumulation on the flowering characteristics of different cultivars were analyzed using a 6℃ artificial low-temperature treatment. The suitable cultivation temperature for early-blooming P. mume cultivars was screened to provide a theoretical basis for further exploration of P. mume bonsai cultivation techniques. The results showed that the flowering rate, flower diameter, flowering quantity, flowering uniformity, and bud development in the 6℃ treatment were significantly better than those in the 10℃ treatment. The flowering rate and quality of different cultivars gradually increased with the accumulation of low-temperature. Therefore, chill accumulation plays a significant role in promoting flowering quality.

In view of the inability to directly and accurately obtain the athlete's aerodynamic force during take-off phase through wind tunnel test, the athlete's aerodynamic force and surrounding flow field form under different take-off postures are obtained through numerical simulation research, and the effects of different take-off modes on the aerodynamic characteristics during take-off in ski jumping are discussed. The multi-body system composed of the athlete and skis was selected as the research objects. By using partially averaged Navier-Stokes (PANS) turbulence model and 3D numerical simulation of computational fluid dynamics (CFD), the aerodynamic characteristics of the athlete under different take-off postures were predicted. Take-off modes include knee-push-hip (KPH) mode and hip-drive-knee (HDK) mode, and the hip joint angle of HDK mode is significantly greater than KPH mode. First, the aerodynamic force ratio of the athlete’s torso and legs is obviously large. Although the aerodynamic force of arms themselves is not obvious, they have a great impact on the overall aerodynamic characteristics of the athlete, so the posture of arms cannot be ignored. Then, the total drag and moment of HDK mode are significantly higher than that of KPH mode, and the lift-to-drag ratio of HDK mode is significantly lower than that of KPH mode. At first the total lift of HDK mode is higher than that of KPH mode, but in the last attitude the total lift of HDK mode does not rise but fall, and finally the total lift of HDK mode is lower than KPH mode. The aerodynamic characteristics change dramatically during take-off phase, and the aerodynamic characteristics of the two take-off modes are quite different, and these changes and differences are difficult to be observed in real training and competition site. KPH mode has obvious aerodynamic advantage over HDK mode. During the take-off process, the athlete should increasethe force generated by the knee joint extension and appropriately reduce the speed of hip joint extension, and control the using force order of the lower limb joints, and push hip joint extension by knee joint extension, in order to avoid issues such as the hip joint angle is too large, the hip joint extension angle is too fast, the center of gravity is to back and other problems. Studying the aerodynamic characteristics during the take-off phase provides valuable insights for athletes to achieve favorable flight postures after take-off, offering scientific guidance to improve training strategies and enhance competitive performance.

Because of the large number of parameters that interact in their function, determining dynamic regime parameters as well as the mode of function of amplifying stages is an extremely complex problem. This paper describes a LabVIEW application for studying the functioning of an ampli-fier in various connections. The user selects the generator's parameters, the type of connection and its parameters, as well as the electric charge characteristics. The application can determine both the stage characteristics and the Bode characteristics. The amplifier's stability zone, as well as its gain and phase, are determined based on these characteristics. An important advantage of this application is that the design of the amplifier stage can be made starting from some param-eters that the amplifier can establish, from which the values of components can be determined. In order to validate the simulation results using the LabVIEW application, a specialized program Multisim was used, as well as experimental measurements using the Electronics Explorer Board. Both Multisim and Electronics Explorer Board can determine Bode characteristics. In both simu-lations and experimental amplifiers, the same schemes with the same transistor was used. The application can be used for educational purposes as well as to design the amplifier's stage to achieve specific parameters.

The post-harvest processes of coffee are widely accepted as key factors in determining the quality of the product. In the Cauca department, Southwestern Colombia, this stage is carried out empirically by farmers in the region, using old methods that do not assure consistent quality. This study proposes to determine the best post-harvest temperature and time conditions for coffee produced in the region. For this purpose, we carried the fermentation and honey process out on different coffee samples of the Coffea Arabica species of the Castillo variety. Subsequently, the cup profile quality of the coffee samples was determined by a sensory evaluation by experts. Finally, we applied descriptive statistical techniques to the resulting data and principal component analysis and hierarchical cluster analysis to find similarities between the samples. The results suggest that the honey process gets better evaluations in the cup profile over any condition of temperature and fermentation time.

Yersiniosis is a common zoonotic enteral disease among humans, which has been linked to pigs and contaminated food, especially pork. Studies on yersiniosis in pets are very scarce. In this study, we performed pheno- and genotypic characterization of 50 Yersinia strains isolated from pets in Finland between 2012 and 2023. Y. enterocolitica 4/O:3/ST135, the most common type in human yersiniosis, was also the most common Y. enterocolitica type (68%) found in clinical faecal samples in our study. Also, human pathogenic Y. enterocolitica 2/O:9/ST139 and Y. pseudotuberculosis O:1/ST9 and O:1/ST42 strains carrying all essential pathogenic genes were identified. Three Y. enterocolitica 4/O:3/ST9 strains were multi-drug resistant and two of them were highly related showing one allelic difference (AD) with core-genome multi-locus sequence typing. Non-pathogenic, genotypically highly diverse Y. enterocolitica 1A strains, showing more than 1000 ADs and missing the essential virulence genes, were also recognized in dogs and cats. Our study demonstrates that pets can excrete human pathogenic Y. enterocolitica and Y. pseudotuberculosis in their faeces and may serve as an infection source for human yersiniosis, especially in families with small children in close contact with their pets.

Alginate extraction is from seaweed, and lignin separation is from by-product corn (stalks and leaves). Alginate/lignin is a synthetic polymer rich in biological activity of great interest. Antioxidant activities of alginate/lignin were evaluated, such as total antioxidant activity, reducing power activity, DPPH free radical scavenging activity, and α – glucosidase inhibition activity. The test of anticancer activity was on four cell lines (Hep G2, fibroblast, MCF-7, and NCI H460). Determination of physical-chemistry characteristics of alginate/lignin was through FTIR, DSC, SEM_EDS, SEM_EDS mapping, XRD, XRF, and 1H-NMR. A study of acute toxicity of alginate/lignin was on Swiss albino mice. The results showed alginate/lignin possessed antioxidant activity such as total antioxidant activity, reducing power activity, especially, α – glucosidase inhibition activity, and no free radical scavenging activity. Alginate/lignin did not be typical in cancer cell lines. Alginate/lignin existed in a thermally stable regular spherical shape in the investigated thermal region. Some specific functional groups of alginate and lignin did not exist in alginate/lignin crystal. Elements such as C, O, Na, and S were popular in the alginate/lignin structure. LD0 and LD100 of alginate/lignin in mice were 3.91 g/kg and 9.77 g/kg, respectively. Alginate/lignin is the potential for application as pharmaceutical materials, functional foods, and supporting diabetes treatment.