As the energy efficiency demands for future buildings become increasingly stringent, preliminary assessments of energy consumption are mandatory. These are possible only through numerical simulations, whose reliability crucially depends on boundary conditions. We therefore investigate their role in numerical estimates for the usage of geothermal energy, performing annual simulations of transient heat transfer for a building employing a geothermal heat pump plant and energy piles. Starting from actual measurements, we solve the heat equations in 2D and 3D using COMSOL Multiphysics and IDA-ICE, and discover a negligible impact of the multiregional ground surface boundary conditions. Moreover, we verify that the thermal mass of the soil medium induces a small vertical temperature gradient on the piles surface. We also find a roughly constant temperature on each horizontal cross-section, with nearly identical values if the average temperature is integrated over the full plane or evaluated at one single point. Calculating the yearly heating need for an entire building we then show that the chosen upper boundary condition affects the energy balance dramatically. Using directly the pipes’ outlet temperature induces a 54% overestimation of the heat flux, while the exact ground surface temperature above the piles reduces the error to 0.03%.

The energy efficiency of ice hockey arenas is a central concern for the administrations, as these buildings are well known to consume a large amount of energy. Since they are composite, complex systems, solutions to such a problem can be approached from many different areas, from managerial to technological to more strictly physical. In this paper we consider heat transfer processes in an ice hockey hall, during operating conditions, with a bottom-up approach based upon on-site measurements. Detailed heat flux, relative humidity and temperature data for the ice pad and the indoor air are used for a heat balance calculation in the steady-state regime, which quantifies the impact of each single heat source. We then solve the heat conduction equation for the ice pad in transient regime, and obtain a generic analytical formula for the temperature profile that can be used in practical applications. We then apply this formula to the resurfacing process for validation, and find good agreement with an analogous numerical solution. Since it is given with implicit initial condition and boundary conditions, it can be used not only in ice hockey halls, but in a large variety of engineering applications.

Heat emitters constitute the primary devices used in space heating and cover a fundamental role in the energy efficient use of buildings. In the search for an optimized design, heating devices should be compared with a benchmark emitter with maximum heat emission efficiency. However, such an ideal heater still needs to be defined. In this paper we perform an analysis of heat transfer in a European reference room, considering room side effects of thermal radiation and computing the induced operative temperature both analytically and numerically. By means of functional optimization, we analyse trends such as the variation of operative temperature with radiator panel dimensions, finding optimal configurations. In order to make our definitions as general as possible, we address panel radiators, convectors, underfloor (UFH) and ceiling heater. We obtain analytical formulas for the operative temperature induced by panel radiators and identify the 10-type as our ideal radiator, while the UFH provides the best performance overall. Regarding specifically UFH and ceiling heaters, we find optimal sizes that identify the according ideal emitters. The analytical method and quantitative results reported in this paper can be generalized and adopted in most studies concerning the efficiency of different heat emitter types in building enclosures.

Estimating heat emission losses of heating systems is an important task of energy efficiency assessments in buildings. To this aim, the present international standards contain tabulated values for different emitter and control system configurations, without however explaining how to compute the effect of increased setpoint temperatures on the system losses. Moreover, the effects of each component are treated as independent, while e.g. vertical stratification and temperature control of the system are cross-related. In this paper we attempt to fill this gap by proposing a calculation method to calculate the product category specific setpoint variations for space heating emitters, accounting for the overall heat balance in the enclosure and including the cross-correlations of each component as well. The emission losses of a heating system are computed using a temperature setpoint variation method that is imposed on annual energy calculations. This complements the procedure presented in the Standard EN15316-2, also providing the possibility to use product-specific values of setpoint variations instead of tabulated values. As the main finding of the study, the calculation process is defined for a European Reference Room, namely for a specific enclosure that allows an accurate and transparent evaluation of the total setpoint variation. The product-specific values of setpoint variations are calculated from measured vertical stratification and control parameters with an annual simulation model of the European Reference Room. The total setpoint variations were simulated for a set of heat emitters and controllers in order to quantify and compare the energy performance of a new and an old type building located in Strasbourg. We find that the total setpoint variation required to overcome emission losses is up to 2.00 °C in the old building and 1.20 °C in the new building, corresponding respectively to an increase in total heating energy usage of up to 22% and 20%.

Large office buildings are responsible for a substantial portion of energy consumption in urban districts. However, thorough assessments regarding the Nordic countries are still lacking. In this paper we analyse the largest dataset to date for a Nordic office building, by considering a case study located in Stockholm, Sweden, that is occupied by nearly a thousand employees.Distinguishing the lighting and occupants’ appliances energy use from heating and cooling, we can estimate the impact of occupancy without any schedule data. A standard frequentist analysis is compared with Bayesian inference, and the according regression formulas are listed in tables that are easy to implement into building performance simulations (BPS). Monthly as well as seasonal correlations are addressed, showing the critical importance of occupancy.A simple method, grounded on the power drain measurements aimed at generating boundary conditions for the BPS, is also introduced; it shows how, for this type of data and number of occupants, no more complexities are needed in order to obtain reliable predictions. For an average year, we overestimate the measured cumulative consumption by only 4.7%. The model can be easily generalised to a variety of datasets.