Today, dental implantology is a reliable technique for the treatment of partial and total edentulism. The fixing of dentures on dental implants can be achieved by a number of different techniques. The choice of technique depends on the specific needs of the patient, the condition of the jawbone and the design of the prosthesis itself. Currently, the two most common types of prosthetic abutment connections are cemented or screwed connections, both of which have disadvantages and ad-vantages. The aim of this study is to analyze, with Finite Element Analysis (FEA), a new Cone Morse connection system between the prosthesis and implant. The connection retention has been analyzed by adopting three different approaches: analytical, in vitro and the FEA method. The systems formed by abutment, healing-cap, and crown with three different inclination conditions were modeled in 3D: 0°, 15° and 30°. With Ansys finite element software, the effect of tilt on system retention was studied. The FEA analysis showed comparable results with in vitro studies regarding the retention strength for an abutment-cap system with a taper of 4°, obtaining 66.6 N compared to 68 N calculated through an in vitro study. The inclination of the abutment affects the retention of the system because the hole made on the surface of the abutment, decreases the contact area between the components. The Cone Morse prosthesis implant connection system is the most stable and efficient system compared to the threaded or cemented system. Retention is influenced by factors such as abutment conicity, insertion strength and the contact surface be-tween components.

Primary stability is an important factor for dental implant success. In the past years, a new method for bone site preparation was introduced, named osseodensification (OD). OD produces a condensation of the trabecular portion of the bone, increasing bone-to-implant contact and primary stability. This study aims to compare the effect of OD in cylindrical and conical implants to conventional instrumentation. A total of 40 implants, divided in 4 groups, were placed in porcine tibia: cylindrical conventional (1a); cylindrical OD (1b); conical conventional (2a); and conical OD (2b). Each implant was measured for implant stability quotient (ISQ), insertion torque (IT) and removal torque (RT). Group 2b showed the higher values for each of the evaluated parameters; groups 1b and 2b showed better results than 1a and 2a, respectively. Regarding IT and RT, group 1b achieved higher values than group 2a, but not for ISQ. The inter-groups comparison showed significant difference between groups 1a vs 2a, 1a vs 2b and 1b vs 2b for ISQ, and 1a vs 1b and 1a vs 2b for RT analysis. OD resulted in improved ISQ, IT and RT of both cylindrical and conical implants. Conical implants groups showed higher ISQ, but cylindrical OD resulted in higher IT and RT, compared to conical conventional ones.

Extreme atrophy of the maxilla poses still challenging for the clinicians. Some of the techniques used could be complex, risky, expensive, time consuming and should be performed, preferably, only by skilled surgeons. Most the commonly used techniques have been reported to have very high success percentages; however, sometimes complications may occur. In this regard, Premaxillary Device (PD) is a technique that has been devised to render more simple the reconstruction of extremely atrophic maxilla, trying to avoid more complicated and risky surgical procedures. Finite Element Analysis (FEA) allows evaluation of several differen aspects of dental implant biomechanics. Our results showed that the use of PD allows an optimal distribution of the stresses on the basal bone, avoiding tension peaks that could determine bone resorption or, even, implant failure. ANSYS has been used to perform this type of localized finite element analysis; with this type of analysis, it was possible to analyze the peri-crestal area of the plant more precisely and the PD through a more accurate reconstruction of the mesh element, which allowed us to mathematically solve the FEA solution. A most favorable biomechanical behavior has been found for the materials such as titanium alloys and reduce stress levels for bone, implants, screws, and abutments. Moreover, the stress values did not exceed bone strength limits for basal bone and titanium alloy. In conclusion, from a biomechanical point of view, PD could be considered a viable alternative for rehabilitation of severe atrophic maxilla.

Peri-implant bone resorption has been reported around some implants after loading and this could create problems for the long-term stability of peri-implant soft and hard tissues. The causes are still not completely known, but a relevant importance could be assumed by the presence of a bacterial contamination at the micro-gap level of the implant-abutment junction. In this regard, external and internal implant-abutment assemblies have been shown to be much more permeable to bacterial colonization than Cone-Morse or conical connections. A subcrestal implant placement could have aesthetic advantages allowing a better prosthetic emergence profile. In literature controversial experimental and clinical results have been reported about bone resorption around implants placed equicrestally and subcrestally. Interestingly, Finite Element Analysis (FEA) studies revealed to be extremely useful for assessing the peri-implant bone strain and stress. Thus, the aim of this study was a FEA evaluation of implants with a Cone-Morse implant-abutment assembly (Implacil De Bortoli, São Paulo, Brazil) inserted into a bone block model (width: 10 mm, vertical height: 17.5 mm, thickness of the cortical area: 1.5 mm) mimicking equicrestal and subcrestal placements (1 and 2 mm). The results demonstrated that maximum stresses were observed within the cortical bone around the equicrestally placed implants, the lowest in the implant placed 2-mm subcrestally and intermediate stresses within the implant placed 1-mm subcrestally. Cortical bone was more stressed under lateral loads than axial loads. In conclusion, this FEA study suggested that implant placement at -1 mm could be recommended.

Keywords: artificial bone; conical implants; cylindrical implants; dental implants; implant stability quotient; insertion torque; polyurethane; post-extraction sites; removal torque.